armv8/ls2085a: Expose all DDR region(s) to Linux
PATCH 16/20 armv8/ls2085a: Expose all DDR region(s) to Linux
From: Bhupesh Sharma <[email protected]>
This patch allows u-boot to expose the complete DDR region(s) to Linux (after subtracting the memory hidden via MEM_TOP_HIDE mechanism).
This allows the u-boot to support the 48-bit VA support provided by ARM64 Linux in flavors 3.18 and above, by passing the appropriate 'memory' DTS nodes.
Signed-off-by Bhupesh Sharma <[email protected]>
Signed-off-by Prabhakar Kushwaha <[email protected]>
--- board/freescale/ls2085a/README | 11 +++++++++++ board/freescale/ls2085a/ls2085a.c | 15 +++++++++------ board/freescale/ls2085aqds/README | 19 +++++++++++++++++++ board/freescale/ls2085aqds/ls2085aqds.c | 15 +++++++++------ board/freescale/ls2085ardb/README | 11 +++++++++++ board/freescale/ls2085ardb/ls2085ardb.c | 15 +++++++++------ 6 files changed, 68 insertions(+), 18 deletions(-)
board/freescale/ls2085a/README +11 -0
@@ -14,3 +14,14 @@ Memory map from core's view Other addresses are either reserved, or not used directly by u-boot. This list should be updated when more addresses are used. + +Booting Linux flavors which do not support 48-bit VA (< Linux 3.18) +------------------------------------------------------------------- +One needs to use appropriate bootargs to boot Linux flavors which do +not support 48-bit VA (for e.g. < Linux 3.18) by appending mem=2048M, as shown +below: + +=> setenv bootargs 'console=ttyS1,115200 root=/dev/ram + earlycon=uart8250,mmio,0x21c0600,115200 default_hugepagesz=2m hugepagesz=2m + hugepages=16 mem=2048M' +
board/freescale/ls2085a/ls2085a.c +9 -6
@@ -127,15 +127,18 @@ void fdt_fixup_board_enet(void *fdt)#ifdef CONFIG_OF_BOARD_SETUP int ft_board_setup (void *blob,bd_t *bd) { -phys_addr_t base; -phys_size_t size; +u64 base[CONFIG_NR_DRAM_BANKS ]; +u64 size[CONFIG_NR_DRAM_BANKS ];ft_cpu_setup (blob, bd); -/* limit the memory size to bank 1 until Linux can handle 40-bit PA */ - base =getenv_bootm_low (); - size =getenv_bootm_size (); -fdt_fixup_memory (blob, (u64 )base, (u64 )size); +/* fixup DT for the two GPP DDR banks */ + base[0 ] = gd->bd->bi_dram[0 ].start; + size[0 ] = gd->bd->bi_dram[0 ].size; + base[1 ] = gd->bd->bi_dram[1 ].start; + size[1 ] = gd->bd->bi_dram[1 ].size; + +fdt_fixup_memory_banks (blob, base, size,2 );#ifdef CONFIG_FSL_MC_ENET fdt_fixup_board_enet (blob);
board/freescale/ls2085aqds/README +19 -0
@@ -127,3 +127,22 @@ b) NOR boot c) NAND boot d) SD boot e) QSPI boot + +Environment Variables +--------------------- +- mcboottimeout: MC boot timeout in milliseconds. If this variable is not defined + the value CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS will be assumed. + +- mcmemsize: MC DRAM block size. If this variable is not defined + the value CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE will be assumed. + +Booting Linux flavors which do not support 48-bit VA (< Linux 3.18) +------------------------------------------------------------------- +One needs to use appropriate bootargs to boot Linux flavors which do +not support 48-bit VA (for e.g. < Linux 3.18) by appending mem=2048M, as shown +below: + +=> setenv bootargs 'console=ttyS1,115200 root=/dev/ram + earlycon=uart8250,mmio,0x21c0600,115200 default_hugepagesz=2m hugepagesz=2m + hugepages=16 mem=2048M' +
board/freescale/ls2085aqds/ls2085aqds.c +9 -6
@@ -244,15 +244,18 @@ void fdt_fixup_board_enet(void *fdt)#ifdef CONFIG_OF_BOARD_SETUP int ft_board_setup (void *blob,bd_t *bd) { -phys_addr_t base; -phys_size_t size; +u64 base[CONFIG_NR_DRAM_BANKS ]; +u64 size[CONFIG_NR_DRAM_BANKS ];ft_cpu_setup (blob, bd); -/* limit the memory size to bank 1 until Linux can handle 40-bit PA */ - base =getenv_bootm_low (); - size =getenv_bootm_size (); -fdt_fixup_memory (blob, (u64 )base, (u64 )size); +/* fixup DT for the two GPP DDR banks */ + base[0 ] = gd->bd->bi_dram[0 ].start; + size[0 ] = gd->bd->bi_dram[0 ].size; + base[1 ] = gd->bd->bi_dram[1 ].start; + size[1 ] = gd->bd->bi_dram[1 ].size; + +fdt_fixup_memory_banks (blob, base, size,2 );#ifdef CONFIG_FSL_MC_ENET fdt_fixup_board_enet (blob);
board/freescale/ls2085ardb/README +11 -0
@@ -107,3 +107,14 @@ Booting Options --------------- a) NOR boot b) NAND boot + +Booting Linux flavors which do not support 48-bit VA (< Linux 3.18) +------------------------------------------------------------------- +One needs to use appropriate bootargs to boot Linux flavors which do +not support 48-bit VA (for e.g. < Linux 3.18) by appending mem=2048M, as shown +below: + +=> setenv bootargs 'console=ttyS1,115200 root=/dev/ram + earlycon=uart8250,mmio,0x21c0600,115200 default_hugepagesz=2m hugepagesz=2m + hugepages=16 mem=2048M' +
board/freescale/ls2085ardb/ls2085ardb.c +9 -6
@@ -241,15 +241,18 @@ void fdt_fixup_board_enet(void *fdt)#ifdef CONFIG_OF_BOARD_SETUP int ft_board_setup (void *blob,bd_t *bd) { -phys_addr_t base; -phys_size_t size; +u64 base[CONFIG_NR_DRAM_BANKS ]; +u64 size[CONFIG_NR_DRAM_BANKS ];ft_cpu_setup (blob, bd); -/* limit the memory size to bank 1 until Linux can handle 40-bit PA */ - base =getenv_bootm_low (); - size =getenv_bootm_size (); -fdt_fixup_memory (blob, (u64 )base, (u64 )size); +/* fixup DT for the two GPP DDR banks */ + base[0 ] = gd->bd->bi_dram[0 ].start; + size[0 ] = gd->bd->bi_dram[0 ].size; + base[1 ] = gd->bd->bi_dram[1 ].start; + size[1 ] = gd->bd->bi_dram[1 ].size; + +fdt_fixup_memory_banks (blob, base, size,2 );#ifdef CONFIG_FSL_MC_ENET fdt_fixup_board_enet (blob);
Signature · 1 line
1.9.1