SPMI regulator driver

new file mode 100644
index 000000000000..75b4604bad07
@@ -0,0 +1,121 @@
+Qualcomm SPMI Regulators
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+			"qcom,pm8841-regulators"
+			"qcom,pm8916-regulators"
+			"qcom,pm8941-regulators"
+
+- interrupts:
+	Usage: optional
+	Value type: <prop-encoded-array>
+	Definition: List of OCP interrupts.
+
+- interrupt-names:
+	Usage: required if 'interrupts' property present
+	Value type: <string-array>
+	Definition: List of strings defining the names of the
+		    interrupts in the 'interrupts' property 1-to-1.
+		    Supported values are "ocp-<regulator_name>", where
+		    <regulator_name> corresponds to a voltage switch
+		    type regulator.
+
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+- vdd_s5-supply:
+- vdd_s6-supply:
+- vdd_s7-supply:
+- vdd_s8-supply:
+	Usage: optional (pm8841 only)
+	Value type: <phandle>
+	Definition: Reference to regulator supplying the input pin, as
+		    described in the data sheet.
+
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+- vdd_l1_l3-supply:
+- vdd_l2-supply:
+- vdd_l4_l5_l6-supply:
+- vdd_l7-supply:
+- vdd_l8_l11_l14_l15_l16-supply:
+- vdd_l9_l10_l12_l13_l17_l18-supply:
+	Usage: optional (pm8916 only)
+	Value type: <phandle>
+	Definition: Reference to regulator supplying the input pin, as
+		    described in the data sheet.
+
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_l1_l3-supply:
+- vdd_l2_lvs_1_2_3-supply:
+- vdd_l4_l11-supply:
+- vdd_l5_l7-supply:
+- vdd_l6_l12_l14_l15-supply:
+- vdd_l8_l16_l18_19-supply:
+- vdd_l9_l10_l17_l22-supply:
+- vdd_l13_l20_l23_l24-supply:
+- vdd_l21-supply:
+- vin_5vs-supply:
+	Usage: optional (pm8941 only)
+	Value type: <phandle>
+	Definition: Reference to regulator supplying the input pin, as
+		    described in the data sheet.
+
+
+The regulator node houses sub-nodes for each regulator within the device. Each
+sub-node is identified using the node's name, with valid values listed for each
+of the PMICs below.
+
+pm8841:
+	s1, s2, s3, s4, s5, s6, s7, s8
+
+pm8916:
+	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
+	l14, l15, l16, l17, l18
+
+pm8941:
+	s1, s2, s3, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14,
+	l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
+	mvs1, mvs2
+
+The content of each sub-node is defined by the standard binding for regulators -
+see regulator.txt - with additional custom properties described below:
+
+- regulator-initial-mode:
+	Usage: optional
+	Value type: <u32>
+	Descrption: 1 = Set initial mode to high power mode (HPM), also referred
+		    to as NPM.  HPM consumes more ground current than LPM, but
+		    it can source significantly higher load current. HPM is not
+		    available on boost type regulators. For voltage switch type
+		    regulators, HPM implies that over current protection and
+		    soft start are active all the time. 0 = Set initial mode to
+		    low power mode (LPM).
+
+Example:
+
+	regulators {
+		compatible = "qcom,pm8941-regulators";
+		vdd_l1_l3-supply = <&s1>;
+
+		s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1400000>;
+		};
+
+		...
+
+		l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		....
+	};

index 7707b989a246..441525ab0cec 100644
@@ -524,6 +524,17 @@ config REGULATOR_QCOM_SMD_RPM
 	  Qualcomm RPM as a module. The module will be named
 	  "qcom_smd-regulator".
 
+config REGULATOR_QCOM_SPMI
+	tristate "Qualcomm SPMI regulator driver"
+	depends on SPMI || COMPILE_TEST
+	help
+	  If you say yes to this option, support will be included for the
+	  regulators found in Qualcomm SPMI PMICs.
+
+	  Say M here if you want to include support for the regulators on the
+	  Qualcomm SPMI PMICs as a module. The module will be named
+	  "qcom_spmi-regulator".
+
 config REGULATOR_RC5T583
 	tristate "RICOH RC5T583 Power regulators"
 	depends on MFD_RC5T583

index da9be8851e01..b737d30d1476 100644
@@ -62,6 +62,7 @@ obj-$(CONFIG_REGULATOR_MC13XXX_CORE) +=  mc13xxx-regulator-core.o
 obj-$(CONFIG_REGULATOR_MT6397)	+= mt6397-regulator.o
 obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o
 obj-$(CONFIG_REGULATOR_QCOM_SMD_RPM) += qcom_smd-regulator.o
+obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o
 obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
 obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
 obj-$(CONFIG_REGULATOR_PWM) += pwm-regulator.o

index abb26b58c83e..553d2d0fe6d9 100644
@@ -37,6 +37,8 @@ Optional properties:
 - regulator-initial-mode: initial operating mode. The set of possible operating
   modes depends on the capabilities of every hardware so each device binding
   documentation explains which values the regulator supports.
+- regulator-system-load: Load in uA present on regulator that is not captured by
+  any consumer request.
 
 Deprecated properties:
 - regulator-compatible: If a regulator chip contains multiple

index 553d2d0fe6d9..6c79fd70ab5a 100644
@@ -39,6 +39,7 @@ Optional properties:
   documentation explains which values the regulator supports.
 - regulator-system-load: Load in uA present on regulator that is not captured by
   any consumer request.
+- regulator-pull-down: Enable pull down resistor when the regulator is disabled.
 
 Deprecated properties:
 - regulator-compatible: If a regulator chip contains multiple

index 6c79fd70ab5a..4b1df61ccbd7 100644
@@ -19,6 +19,7 @@ Optional properties:
   design requires. This property describes the total system ramp time
   required due to the combination of internal ramping of the regulator itself,
   and board design issues such as trace capacitance and load on the supply.
+- regulator-soft-start: Enable soft start so that voltage ramps slowly
 - regulator-state-mem sub-root node for Suspend-to-RAM mode
   : suspend to memory, the device goes to sleep, but all data stored in memory,
   only some external interrupt can wake the device.

index 4b1df61ccbd7..e29db73e55f4 100644
@@ -7,6 +7,7 @@ Optional properties:
 - regulator-microvolt-offset: Offset applied to voltages to compensate for voltage drops
 - regulator-min-microamp: smallest current consumers may set
 - regulator-max-microamp: largest current consumers may set
+- regulator-input-current-limit-microamp: maximum input current regulator allows
 - regulator-always-on: boolean, regulator should never be disabled
 - regulator-boot-on: bootloader/firmware enabled regulator
 - regulator-allow-bypass: allow the regulator to go into bypass mode

index 75b4604bad07..ab01a152e930 100644
@@ -99,6 +99,68 @@ see regulator.txt - with additional custom properties described below:
 		    soft start are active all the time. 0 = Set initial mode to
 		    low power mode (LPM).
 
+- qcom,auto-mode-enable:
+	Usage: optional
+	Value type: <u32>
+	Description: 1 = Enable automatic hardware selection of regulator
+			 mode (HPM vs LPM); not available on boost type
+			 regulators. 0 = Disable auto mode selection.
+
+- qcom,ocp-enable:
+	Usage: optional
+	Value type: <u32>
+	Description: 1 = Allow over current protection (OCP) to be enabled for
+		     voltage switch type regulators so that they latch off
+		     automatically when over current is detected. OCP is
+		     enabled when in HPM or auto mode.  0 = Disable OCP.
+
+- qcom,ocp-max-retries:
+	Usage: optional
+	Value type: <u32>
+	Description: Maximum number of times to try toggling a voltage switch
+		     off and back on as a result of consecutive over current
+		     events.
+
+- qcom,ocp-retry-delay:
+	Usage: optional
+	Value type: <u32>
+	Description: Time to delay in milliseconds between each voltage switch
+		     toggle after an over current event takes place.
+
+- qcom,pin-ctrl-enable:
+	Usage: optional
+	Value type: <u32>
+	Description: Bit mask specifying which hardware pins should be used to
+		     enable the regulator, if any; supported bits are:
+			0 = ignore all hardware enable signals
+			BIT(0) = follow HW0_EN signal
+			BIT(1) = follow HW1_EN signal
+			BIT(2) = follow HW2_EN signal
+			BIT(3) = follow HW3_EN signal
+
+- qcom,pin-ctrl-hpm:
+	Usage: optional
+	Value type: <u32>
+	Description: Bit mask specifying which hardware pins should be used to
+		     force the regulator into high power mode, if any;
+		     supported bits are:
+			0 = ignore all hardware enable signals
+			BIT(0) = follow HW0_EN signal
+			BIT(1) = follow HW1_EN signal
+			BIT(2) = follow HW2_EN signal
+			BIT(3) = follow HW3_EN signal
+			BIT(4) = follow PMIC awake state
+
+- qcom,vs-soft-start-strength:
+	Usage: optional
+	Value type: <u32>
+	Description: This property sets the soft start strength for voltage
+		     switch type regulators; supported values are:
+			0 = 0.05 uA
+			1 = 0.25 uA
+			2 = 0.55 uA
+			3 = 0.75 uA
+
 Example:
 
 	regulators {