fm10k: use dma_set_mask_and_coherent in fm10k_probe
Subsystems (2)
PATCH 1/1 fm10k: use dma_set_mask_and_coherent in fm10k_probe
This patch cleans up the use of dma_get_required_mask and uses the simpler dma_set_mask_and_coherent function instead of doing these as separate steps.
I removed the dma_get_required_mask call because based on some minimal testing it appears that either (a) we're not doing the right thing with the call or (b) we don't need it anyways. If the value returned is <48bits, we'll end up trying with 48 bits anyways. If it's over 48bits, fm10k can't support that anyways, and we should try 48bits. If 48bits fails, we'll fallback to 32bits. This cleans up some very funky code.
- rc2
* add back goto err_dma
- rc3
* use %d for error code printf
--- drivers/net/ethernet/intel/fm10k/fm10k_pci.c | 24 ++++++------------------ 1 file changed, 6 insertions(+), 18 deletions(-)
drivers/net/ethernet/intel/fm10k/fm10k_pci.c +6 -18
@@ -1741,30 +1741,18 @@ static int fm10k_probe(struct pci_dev *pdev,struct fm10k_intfc *interface;struct fm10k_hw *hw;int err; -u64 dma_mask; err =pci_enable_device_mem (pdev);if (err)return err; -/* By default fm10k only supports a 48 bit DMA mask */ - dma_mask =DMA_BIT_MASK (48 ) |dma_get_required_mask (&pdev->dev); - -if ((dma_mask <=DMA_BIT_MASK (32 )) || -dma_set_mask_and_coherent (&pdev->dev, dma_mask)) { - dma_mask &=DMA_BIT_MASK (32 ); - + err =dma_set_mask_and_coherent (&pdev->dev,DMA_BIT_MASK (48 )); +if (err) err =dma_set_mask_and_coherent (&pdev->dev,DMA_BIT_MASK (32 )); - err =dma_set_mask (&pdev->dev,DMA_BIT_MASK (32 )); -if (err) { - err =dma_set_coherent_mask (&pdev->dev, -DMA_BIT_MASK (32 )); -if (err) { -dev_err (&pdev->dev, -"No usable DMA configuration, aborting\n" ); - goto err_dma; - } - } +if (err) { +dev_err (&pdev->dev, +"DMA configuration failed: %d\n" , err); + goto err_dma; } err = pci_request_selected_regions(pdev,
Signature · 1 line
2.4.2
Singh
PATCH 1/1 fm10k: use dma_set_mask_and_coherent in fm10k_probe
-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On Behalf Of Jacob Keller
Sent: Tuesday, June 16, 2015 1:42 PM
To: Intel Wired LAN <[email protected]>
Subject: [Intel-wired-lan] [PATCH rc3] fm10k: use dma_set_mask_and_coherent in fm10k_probe
This patch cleans up the use of dma_get_required_mask and uses the simpler dma_set_mask_and_coherent function instead of doing these as separate steps.
I removed the dma_get_required_mask call because based on some minimal testing it appears that either (a) we're not doing the right thing with the call or (b) we don't need it anyways. If the value returned is <48bits, we'll end up trying with 48 bits anyways. If it's over 48bits, fm10k can't support that anyways, and we should try 48bits. If 48bits fails, we'll fallback to 32bits. This cleans up some very funky code.
- rc2
* add back goto err_dma
- rc3
* use %d for error code printf
---
_______________________________________________
Intel-wired-lan mailing list
Intel-wired-lan at lists.osuosl.org
http://lists.osuosl.org/mailman/listinfo/intel-wired-lan