drm/i915: VLV/CHV DPLL workarounds and cleanups
Subsystems (2)
cover drm/i915: VLV/CHV DPLL workarounds and cleanups
From: Ville Syrjälä <[email protected]>
While trawling the w/a database I spotted a workaround we didn't have related to CHV DPLL pixel multiuplier setting. So I set forth to implement it, and while doing that I ended up cleaning up the VLV/CHV DPLL handling a bit. This also touched the DSI code a bit and while testing that I noticed some problems with out DSI PLL handling so I included a fix for those.
Ville Syrjälä (9):
drm/i915: Keep GMCH DPLL VGA mode always disabled drm/i915: Apply OCD to VLV/CHV DPLL defines
drm/i915: Simplify CHV pipe A power well code drm/i915: Refactor VLV display power well init/deinit drm/i915: Clear out DPLL state from pipe config in DSI get config drm/i915: Move DPLL ref/cri/VGA mode frobbing to the disp2d well
enable
drm/i915: Make {vlv,chv}_{disable,update}_pll() more similar drm/i915: Implement WaPixelRepeatModeFixForC0:chv drm/i915: Disable DSI PLL before reconfiguring it
drivers/gpu/drm/i915/i915_drv.h | 7 ++ drivers/gpu/drm/i915/i915_reg.h | 9 ++- drivers/gpu/drm/i915/intel_display.c | 99 +++++++++++++++------------- drivers/gpu/drm/i915/intel_dsi.c | 16 ++--- drivers/gpu/drm/i915/intel_runtime_pm.c | 110 +++++++++++++++----------------- 5 files changed, 124 insertions(+), 117 deletions(-)
Signature · 6 lines
2.3.6 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 1/9 drm/i915: Keep GMCH DPLL VGA mode always disabled
From: Ville Syrjälä <[email protected]>
We disable the DPLL VGA mode when enabling the DPLL, but we enaable it again when disabling the DPLL. Having VGA mode enabled even in unused DPLLs can cause problems for CHV, so it seems wiser to always keep it disabled. And let's just do that on all GMCH platforms to keep things as similar as possible between them.
--- drivers/gpu/drm/i915/intel_display.c | 8 +++++--- drivers/gpu/drm/i915/intel_dsi.c | 2 +- drivers/gpu/drm/i915/intel_runtime_pm.c | 8 ++++---- 3 files changed, 10 insertions(+), 8 deletions(-)
drivers/gpu/drm/i915/intel_display.c +5 -3
@@ -1774,13 +1774,13 @@ static void i9xx_disable_pll(struct intel_crtc *crtc)/* Make sure the pipe isn't still relying on us */ assert_pipe_disabled (dev_priv, pipe); -I915_WRITE (DPLL (pipe),0 ); +I915_WRITE (DPLL (pipe),DPLL_VGA_MODE_DIS );POSTING_READ (DPLL (pipe)); }static void vlv_disable_pll (struct drm_i915_private *dev_priv,enum pipe pipe) { -u32 val =0 ; +u32 val;/* Make sure the pipe isn't still relying on us */ assert_pipe_disabled (dev_priv, pipe);
@@ -1789,6 +1789,7 @@ static void vlv_disable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)* Leave integrated clock source and reference clock enabled for pipe B. * The latter is needed for VGA hotplug / manual detection. */ + val =DPLL_VGA_MODE_DIS ;if (pipe ==PIPE_B ) val =DPLL_INTEGRATED_CRI_CLK_VLV |DPLL_REFA_CLK_ENABLE_VLV ;I915_WRITE (DPLL (pipe), val);
@@ -1805,7 +1806,8 @@ static void chv_disable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)assert_pipe_disabled (dev_priv, pipe);/* Set PLL en = 0 */ - val =DPLL_SSC_REF_CLOCK_CHV |DPLL_REFA_CLK_ENABLE_VLV ; + val =DPLL_SSC_REF_CLOCK_CHV | +DPLL_REFA_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ;if (pipe !=PIPE_A ) val |=DPLL_INTEGRATED_CRI_CLK_VLV ;I915_WRITE (DPLL (pipe), val);
drivers/gpu/drm/i915/intel_dsi.c +1 -1
@@ -427,7 +427,7 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* update the hw state for DPLL */ intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_CLOCK_VLV | -DPLL_REFA_CLK_ENABLE_VLV ; +DPLL_REFA_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;
drivers/gpu/drm/i915/intel_runtime_pm.c +4 -4
@@ -882,7 +882,7 @@ static void vlv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv,* display and the reference clock for VGA * hotplug / manual detection. */ -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) | +I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS |DPLL_REFA_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV );udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */
@@ -933,13 +933,13 @@ static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv,*/ if (power_well->data ==PUNIT_POWER_WELL_DPIO_CMN_BC ) { phy =DPIO_PHY0 ; -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) | +I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS |DPLL_REFA_CLK_ENABLE_VLV ); -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) | +I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS |DPLL_REFA_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); }else { phy =DPIO_PHY1 ; -I915_WRITE (DPLL (PIPE_C ),I915_READ (DPLL (PIPE_C )) | +I915_WRITE (DPLL (PIPE_C ),I915_READ (DPLL (PIPE_C )) |DPLL_VGA_MODE_DIS |DPLL_REFA_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); }udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */
Signature · 6 lines
2.3.6 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 1/9] drm/i915: Keep GMCH DPLL VGA mode always disabled
Quoted 86 lines · On 6/29/2015 5:55 PM, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
We disable the DPLL VGA mode when enabling the DPLL, but we enaable it again when disabling the DPLL. Having VGA mode enabled even in unused DPLLs can cause problems for CHV, so it seems wiser to always keep it disabled. And let's just do that on all GMCH platforms to keep things as similar as possible between them.
Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_display.c | 8 +++++--- drivers/gpu/drm/i915/intel_dsi.c | 2 +- drivers/gpu/drm/i915/intel_runtime_pm.c | 8 ++++---- 3 files changed, 10 insertions(+), 8 deletions(-)drivers/gpu/drm/i915/intel_display.c +5
-3@@ -1774,13 +1774,13 @@ static void i9xx_disable_pll(struct intel_crtc *crtc)/* Make sure the pipe isn't still relying on us */ assert_pipe_disabled (dev_priv, pipe); -I915_WRITE (DPLL (pipe),0 ); +I915_WRITE (DPLL (pipe),DPLL_VGA_MODE_DIS );POSTING_READ (DPLL (pipe)); }static void vlv_disable_pll (struct drm_i915_private *dev_priv,enum pipe pipe) { -u32 val =0 ; +u32 val;/* Make sure the pipe isn't still relying on us */ assert_pipe_disabled (dev_priv, pipe);@@ -1789,6 +1789,7 @@ static void vlv_disable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)* Leave integrated clock source and reference clock enabled for pipe B. * The latter is needed for VGA hotplug / manual detection. */ + val =DPLL_VGA_MODE_DIS ;if (pipe ==PIPE_B ) val =DPLL_INTEGRATED_CRI_CLK_VLV |DPLL_REFA_CLK_ENABLE_VLV ;I915_WRITE (DPLL (pipe), val);@@ -1805,7 +1806,8 @@ static void chv_disable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)assert_pipe_disabled (dev_priv, pipe);/* Set PLL en = 0 */ - val =DPLL_SSC_REF_CLOCK_CHV |DPLL_REFA_CLK_ENABLE_VLV ; + val =DPLL_SSC_REF_CLOCK_CHV | +DPLL_REFA_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ;if (pipe !=PIPE_A ) val |=DPLL_INTEGRATED_CRI_CLK_VLV ;I915_WRITE (DPLL (pipe), val);drivers/gpu/drm/i915/intel_dsi.c +1
-1@@ -427,7 +427,7 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* update the hw state for DPLL */ intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_CLOCK_VLV | -DPLL_REFA_CLK_ENABLE_VLV ; +DPLL_REFA_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;drivers/gpu/drm/i915/intel_runtime_pm.c +2
-2@@ -882,7 +882,7 @@ static void vlv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv,* display and the reference clock for VGA * hotplug / manual detection. */ -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) | +I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS |DPLL_REFA_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV );udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */ @@ -933,13 +933,13 @@ static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv,*/ if (power_well->data ==PUNIT_POWER_WELL_DPIO_CMN_BC ) { phy =DPIO_PHY0 ; -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) | +I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS |DPLL_REFA_CLK_ENABLE_VLV );
drivers/gpu/drm/i915/intel_runtime_pm.c static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv, · line 945
Quoted 10 lines
drivers/gpu/drm/i915/intel_runtime_pm.c +2
-2-I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) | +I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS |DPLL_REFA_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); }else { phy =DPIO_PHY1 ; -I915_WRITE (DPLL (PIPE_C ),I915_READ (DPLL (PIPE_C )) | +I915_WRITE (DPLL (PIPE_C ),I915_READ (DPLL (PIPE_C )) |DPLL_VGA_MODE_DIS |DPLL_REFA_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); }udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */
since we keep DPLL_VGA_MODE_DIS always set, even during disable is this needed explicitly again here ? other than this i am fine with this.
Signature · 7 lines
regards, Sivakumar _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 1/9] drm/i915: Keep GMCH DPLL VGA mode always disabled
Quoted 101 lines · Sivakumar Thulasimani
Quoted 86 lines · On 6/29/2015 5:55 PM, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
We disable the DPLL VGA mode when enabling the DPLL, but we enaable it again when disabling the DPLL. Having VGA mode enabled even in unused DPLLs can cause problems for CHV, so it seems wiser to always keep it disabled. And let's just do that on all GMCH platforms to keep things as similar as possible between them.
Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_display.c | 8 +++++--- drivers/gpu/drm/i915/intel_dsi.c | 2 +- drivers/gpu/drm/i915/intel_runtime_pm.c | 8 ++++---- 3 files changed, 10 insertions(+), 8 deletions(-)drivers/gpu/drm/i915/intel_display.c +5
-3@@ -1774,13 +1774,13 @@ static void i9xx_disable_pll(struct intel_crtc *crtc)/* Make sure the pipe isn't still relying on us */ assert_pipe_disabled (dev_priv, pipe); -I915_WRITE (DPLL (pipe),0 ); +I915_WRITE (DPLL (pipe),DPLL_VGA_MODE_DIS );POSTING_READ (DPLL (pipe)); }static void vlv_disable_pll (struct drm_i915_private *dev_priv,enum pipe pipe) { -u32 val =0 ; +u32 val;/* Make sure the pipe isn't still relying on us */ assert_pipe_disabled (dev_priv, pipe);@@ -1789,6 +1789,7 @@ static void vlv_disable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)* Leave integrated clock source and reference clock enabled for pipe B. * The latter is needed for VGA hotplug / manual detection. */ + val =DPLL_VGA_MODE_DIS ;if (pipe ==PIPE_B ) val =DPLL_INTEGRATED_CRI_CLK_VLV |DPLL_REFA_CLK_ENABLE_VLV ;I915_WRITE (DPLL (pipe), val);@@ -1805,7 +1806,8 @@ static void chv_disable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)assert_pipe_disabled (dev_priv, pipe);/* Set PLL en = 0 */ - val =DPLL_SSC_REF_CLOCK_CHV |DPLL_REFA_CLK_ENABLE_VLV ; + val =DPLL_SSC_REF_CLOCK_CHV | +DPLL_REFA_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ;if (pipe !=PIPE_A ) val |=DPLL_INTEGRATED_CRI_CLK_VLV ;I915_WRITE (DPLL (pipe), val);drivers/gpu/drm/i915/intel_dsi.c +1
-1@@ -427,7 +427,7 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* update the hw state for DPLL */ intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_CLOCK_VLV | -DPLL_REFA_CLK_ENABLE_VLV ; +DPLL_REFA_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;drivers/gpu/drm/i915/intel_runtime_pm.c +2
-2@@ -882,7 +882,7 @@ static void vlv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv,* display and the reference clock for VGA * hotplug / manual detection. */ -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) | +I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS |DPLL_REFA_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV );udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */ @@ -933,13 +933,13 @@ static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv,*/ if (power_well->data ==PUNIT_POWER_WELL_DPIO_CMN_BC ) { phy =DPIO_PHY0 ; -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) | +I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS |DPLL_REFA_CLK_ENABLE_VLV );drivers/gpu/drm/i915/intel_runtime_pm.c static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv, · line 945
Quoted 10 lines
drivers/gpu/drm/i915/intel_runtime_pm.c +2
-2-I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) | +I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS |DPLL_REFA_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); }else { phy =DPIO_PHY1 ; -I915_WRITE (DPLL (PIPE_C ),I915_READ (DPLL (PIPE_C )) | +I915_WRITE (DPLL (PIPE_C ),I915_READ (DPLL (PIPE_C )) |DPLL_VGA_MODE_DIS |DPLL_REFA_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); }udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */ since we keep
DPLL_VGA_MODE_DISalways set, even during disable is this needed explicitly again here ? other than this i am fine with this.
Quoted 1 line
Reviewed-by Sivakumar Thulasimani <[email protected]>
Yes we still need this because during driver init the BIOS may have left it enabled, and the register loses state when the disp2d/pipe-a power well goes down and the poweron default has VGA mode enabled.
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 2/9 drm/i915: Apply OCD to VLV/CHV DPLL defines
In reply to [email protected]From: Ville Syrjälä <[email protected]>
Drop the spurious 'A' from the VLV/CHV ref clock enable define, and add the "REF" to the VLV ref clock selection bit. Also s/CLOCK/CLK/ for extra consistency.
--- drivers/gpu/drm/i915/i915_reg.h | 6 +++--- drivers/gpu/drm/i915/intel_display.c | 14 +++++++------- drivers/gpu/drm/i915/intel_dsi.c | 6 +++--- drivers/gpu/drm/i915/intel_runtime_pm.c | 8 ++++---- 4 files changed, 17 insertions(+), 17 deletions(-)
drivers/gpu/drm/i915/i915_reg.h +3 -3
@@ -2127,7 +2127,7 @@ enum skl_disp_power_wells {#define DPLL_DVO_2X_MODE (1 << 30)#define DPLL_EXT_BUFFER_ENABLE_VLV (1 << 30)#define DPLL_SYNCLOCK_ENABLE (1 << 29) -#define DPLL_REFA_CLK_ENABLE_VLV (1 << 29) +#define DPLL_REF_CLK_ENABLE_VLV (1 << 29)#define DPLL_VGA_MODE_DIS (1 << 28)#define DPLLB_MODE_DAC_SERIAL (1 << 26)/* i915 */ #define DPLLB_MODE_LVDS (2 << 26)/* i915 */
@@ -2141,8 +2141,8 @@ enum skl_disp_power_wells {#define DPLL_FPA01_P1_POST_DIV_MASK_PINEVIEW 0x00ff8000/* Pineview */ #define DPLL_LOCK_VLV (1<<15)#define DPLL_INTEGRATED_CRI_CLK_VLV (1<<14) -#define DPLL_INTEGRATED_CLOCK_VLV (1<<13) -#define DPLL_SSC_REF_CLOCK_CHV (1<<13) +#define DPLL_INTEGRATED_REF_CLK_VLV (1<<13) +#define DPLL_SSC_REF_CLK_CHV (1<<13)#define DPLL_PORTC_READY_MASK (0xf << 4)#define DPLL_PORTB_READY_MASK (0xf)
drivers/gpu/drm/i915/intel_display.c +7 -7
@@ -1791,7 +1791,7 @@ static void vlv_disable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)*/ val =DPLL_VGA_MODE_DIS ;if (pipe ==PIPE_B ) - val =DPLL_INTEGRATED_CRI_CLK_VLV |DPLL_REFA_CLK_ENABLE_VLV ; + val =DPLL_INTEGRATED_CRI_CLK_VLV |DPLL_REF_CLK_ENABLE_VLV ;I915_WRITE (DPLL (pipe), val);POSTING_READ (DPLL (pipe));
@@ -1806,8 +1806,8 @@ static void chv_disable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)assert_pipe_disabled (dev_priv, pipe);/* Set PLL en = 0 */ - val =DPLL_SSC_REF_CLOCK_CHV | -DPLL_REFA_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; + val =DPLL_SSC_REF_CLK_CHV | +DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ;if (pipe !=PIPE_A ) val |=DPLL_INTEGRATED_CRI_CLK_VLV ;I915_WRITE (DPLL (pipe), val);
@@ -7198,8 +7198,8 @@ static void vlv_update_pll(struct intel_crtc *crtc,* clock for pipe B, since VGA hotplug / manual detection depends * on it. */ - dpll =DPLL_EXT_BUFFER_ENABLE_VLV |DPLL_REFA_CLK_ENABLE_VLV | -DPLL_VGA_MODE_DIS |DPLL_INTEGRATED_CLOCK_VLV ; + dpll =DPLL_EXT_BUFFER_ENABLE_VLV |DPLL_REF_CLK_ENABLE_VLV | +DPLL_VGA_MODE_DIS |DPLL_INTEGRATED_REF_CLK_VLV ;/* We should never disable this, set it here for state tracking */ if (crtc->pipe ==PIPE_B ) dpll |=DPLL_INTEGRATED_CRI_CLK_VLV ;
@@ -7305,8 +7305,8 @@ static void vlv_prepare_pll(struct intel_crtc *crtc,static void chv_update_pll (struct intel_crtc *crtc,struct intel_crtc_state *pipe_config) { - pipe_config->dpll_hw_state.dpll =DPLL_SSC_REF_CLOCK_CHV | -DPLL_REFA_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS | + pipe_config->dpll_hw_state.dpll =DPLL_SSC_REF_CLK_CHV | +DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS |DPLL_VCO_ENABLE ;if (crtc->pipe !=PIPE_A ) pipe_config->dpll_hw_state.dpll |=DPLL_INTEGRATED_CRI_CLK_VLV ;
drivers/gpu/drm/i915/intel_dsi.c +3 -3
@@ -422,12 +422,12 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* Disable DPOunit clock gating, can stall pipe * and we need DPLL REFA always enabled */ tmp =I915_READ (DPLL (pipe)); - tmp |=DPLL_REFA_CLK_ENABLE_VLV ; + tmp |=DPLL_REF_CLK_ENABLE_VLV ;I915_WRITE (DPLL (pipe), tmp);/* update the hw state for DPLL */ - intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_CLOCK_VLV | -DPLL_REFA_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; + intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_REF_CLK_VLV | +DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;
drivers/gpu/drm/i915/intel_runtime_pm.c +4 -4
@@ -883,7 +883,7 @@ static void vlv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv,* hotplug / manual detection. */ I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS | -DPLL_REFA_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); +DPLL_REF_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV );udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */ vlv_set_power_well (dev_priv, power_well, true);
@@ -934,13 +934,13 @@ static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv,if (power_well->data ==PUNIT_POWER_WELL_DPIO_CMN_BC ) { phy =DPIO_PHY0 ;I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS | -DPLL_REFA_CLK_ENABLE_VLV ); +DPLL_REF_CLK_ENABLE_VLV );I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS | -DPLL_REFA_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); +DPLL_REF_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); }else { phy =DPIO_PHY1 ;I915_WRITE (DPLL (PIPE_C ),I915_READ (DPLL (PIPE_C )) |DPLL_VGA_MODE_DIS | -DPLL_REFA_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); +DPLL_REF_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); }udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */ vlv_set_power_well (dev_priv, power_well, true);
Signature · 6 lines
2.3.6 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/9] drm/i915: Apply OCD to VLV/CHV DPLL defines
Quoted 134 lines · On 6/29/2015 5:55 PM, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
Drop the spurious 'A' from the VLV/CHV ref clock enable define, and add the "REF" to the VLV ref clock selection bit. Also s/CLOCK/CLK/ for extra consistency.
Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/i915_reg.h | 6 +++--- drivers/gpu/drm/i915/intel_display.c | 14 +++++++------- drivers/gpu/drm/i915/intel_dsi.c | 6 +++--- drivers/gpu/drm/i915/intel_runtime_pm.c | 8 ++++---- 4 files changed, 17 insertions(+), 17 deletions(-)drivers/gpu/drm/i915/i915_reg.h +3
-3@@ -2127,7 +2127,7 @@ enum skl_disp_power_wells {#define DPLL_DVO_2X_MODE (1 << 30)#define DPLL_EXT_BUFFER_ENABLE_VLV (1 << 30)#define DPLL_SYNCLOCK_ENABLE (1 << 29) -#define DPLL_REFA_CLK_ENABLE_VLV (1 << 29) +#define DPLL_REF_CLK_ENABLE_VLV (1 << 29)#define DPLL_VGA_MODE_DIS (1 << 28)#define DPLLB_MODE_DAC_SERIAL (1 << 26)/* i915 */ #define DPLLB_MODE_LVDS (2 << 26)/* i915 */ @@ -2141,8 +2141,8 @@ enum skl_disp_power_wells {#define DPLL_FPA01_P1_POST_DIV_MASK_PINEVIEW 0x00ff8000/* Pineview */ #define DPLL_LOCK_VLV (1<<15)#define DPLL_INTEGRATED_CRI_CLK_VLV (1<<14) -#define DPLL_INTEGRATED_CLOCK_VLV (1<<13) -#define DPLL_SSC_REF_CLOCK_CHV (1<<13) +#define DPLL_INTEGRATED_REF_CLK_VLV (1<<13) +#define DPLL_SSC_REF_CLK_CHV (1<<13)#define DPLL_PORTC_READY_MASK (0xf << 4)#define DPLL_PORTB_READY_MASK (0xf)drivers/gpu/drm/i915/intel_display.c +7
-7@@ -1791,7 +1791,7 @@ static void vlv_disable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)*/ val =DPLL_VGA_MODE_DIS ;if (pipe ==PIPE_B ) - val =DPLL_INTEGRATED_CRI_CLK_VLV |DPLL_REFA_CLK_ENABLE_VLV ; + val =DPLL_INTEGRATED_CRI_CLK_VLV |DPLL_REF_CLK_ENABLE_VLV ;I915_WRITE (DPLL (pipe), val);POSTING_READ (DPLL (pipe));@@ -1806,8 +1806,8 @@ static void chv_disable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)assert_pipe_disabled (dev_priv, pipe);/* Set PLL en = 0 */ - val =DPLL_SSC_REF_CLOCK_CHV | -DPLL_REFA_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; + val =DPLL_SSC_REF_CLK_CHV | +DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ;if (pipe !=PIPE_A ) val |=DPLL_INTEGRATED_CRI_CLK_VLV ;I915_WRITE (DPLL (pipe), val);@@ -7198,8 +7198,8 @@ static void vlv_update_pll(struct intel_crtc *crtc,* clock for pipe B, since VGA hotplug / manual detection depends * on it. */ - dpll =DPLL_EXT_BUFFER_ENABLE_VLV |DPLL_REFA_CLK_ENABLE_VLV | -DPLL_VGA_MODE_DIS |DPLL_INTEGRATED_CLOCK_VLV ; + dpll =DPLL_EXT_BUFFER_ENABLE_VLV |DPLL_REF_CLK_ENABLE_VLV | +DPLL_VGA_MODE_DIS |DPLL_INTEGRATED_REF_CLK_VLV ;/* We should never disable this, set it here for state tracking */ if (crtc->pipe ==PIPE_B ) dpll |=DPLL_INTEGRATED_CRI_CLK_VLV ;@@ -7305,8 +7305,8 @@ static void vlv_prepare_pll(struct intel_crtc *crtc,static void chv_update_pll (struct intel_crtc *crtc,struct intel_crtc_state *pipe_config) { - pipe_config->dpll_hw_state.dpll =DPLL_SSC_REF_CLOCK_CHV | -DPLL_REFA_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS | + pipe_config->dpll_hw_state.dpll =DPLL_SSC_REF_CLK_CHV | +DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS |DPLL_VCO_ENABLE ;if (crtc->pipe !=PIPE_A ) pipe_config->dpll_hw_state.dpll |=DPLL_INTEGRATED_CRI_CLK_VLV ;drivers/gpu/drm/i915/intel_dsi.c +3
-3@@ -422,12 +422,12 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* Disable DPOunit clock gating, can stall pipe * and we need DPLL REFA always enabled */ tmp =I915_READ (DPLL (pipe)); - tmp |=DPLL_REFA_CLK_ENABLE_VLV ; + tmp |=DPLL_REF_CLK_ENABLE_VLV ;I915_WRITE (DPLL (pipe), tmp);/* update the hw state for DPLL */ - intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_CLOCK_VLV | -DPLL_REFA_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; + intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_REF_CLK_VLV | +DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;drivers/gpu/drm/i915/intel_runtime_pm.c +4
-4@@ -883,7 +883,7 @@ static void vlv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv,* hotplug / manual detection. */ I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS | -DPLL_REFA_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); +DPLL_REF_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV );udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */ vlv_set_power_well (dev_priv, power_well, true);@@ -934,13 +934,13 @@ static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv,if (power_well->data ==PUNIT_POWER_WELL_DPIO_CMN_BC ) { phy =DPIO_PHY0 ;I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS | -DPLL_REFA_CLK_ENABLE_VLV ); +DPLL_REF_CLK_ENABLE_VLV );I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS | -DPLL_REFA_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); +DPLL_REF_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); }else { phy =DPIO_PHY1 ;I915_WRITE (DPLL (PIPE_C ),I915_READ (DPLL (PIPE_C )) |DPLL_VGA_MODE_DIS | -DPLL_REFA_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); +DPLL_REF_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); }udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */ vlv_set_power_well (dev_priv, power_well, true);
Signature · 7 lines
regards, Sivakumar _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 3/9 drm/i915: Simplify CHV pipe A power well code
In reply to [email protected]From: Ville Syrjälä <[email protected]>
The pipe A power well is the "disp2d" well on CHV and pipe B and C wells don't even exist. Thereforce we can remove the checks for pipe A vs. others and just assume it's always pipe A.
--- drivers/gpu/drm/i915/intel_runtime_pm.c | 47 ++++++++++++++------------------- 1 file changed, 20 insertions(+), 27 deletions(-)
drivers/gpu/drm/i915/intel_runtime_pm.c +20 -27
@@ -1042,53 +1042,46 @@ out:static void chv_pipe_power_well_sync_hw (struct drm_i915_private *dev_priv,struct i915_power_well *power_well) { +WARN_ON_ONCE (power_well->data !=PIPE_A ); +chv_set_pipe_power_well (dev_priv, power_well, power_well->count >0 ); }static void chv_pipe_power_well_enable (struct drm_i915_private *dev_priv,struct i915_power_well *power_well) { -WARN_ON_ONCE (power_well->data !=PIPE_A && - power_well->data !=PIPE_B && - power_well->data !=PIPE_C ); +WARN_ON_ONCE (power_well->data !=PIPE_A );chv_set_pipe_power_well (dev_priv, power_well, true); -if (power_well->data ==PIPE_A ) { -spin_lock_irq (&dev_priv->irq_lock); -valleyview_enable_display_irqs (dev_priv); -spin_unlock_irq (&dev_priv->irq_lock); +spin_lock_irq (&dev_priv->irq_lock); +valleyview_enable_display_irqs (dev_priv); +spin_unlock_irq (&dev_priv->irq_lock); -/* -* During driver initialization/resume we can avoid restoring the -* part of the HW/SW state that will be inited anyway explicitly. -*/ -if (dev_priv->power_domains.initializing) -return ; +/* +* During driver initialization/resume we can avoid restoring the +* part of the HW/SW state that will be inited anyway explicitly. +*/ +if (dev_priv->power_domains.initializing) +return ; -intel_hpd_init (dev_priv); +intel_hpd_init (dev_priv); -i915_redisable_vga_power_on (dev_priv->dev); - } +i915_redisable_vga_power_on (dev_priv->dev); }static void chv_pipe_power_well_disable (struct drm_i915_private *dev_priv,struct i915_power_well *power_well) { -WARN_ON_ONCE (power_well->data !=PIPE_A && - power_well->data !=PIPE_B && - power_well->data !=PIPE_C ); - -if (power_well->data ==PIPE_A ) { -spin_lock_irq (&dev_priv->irq_lock); -valleyview_disable_display_irqs (dev_priv); -spin_unlock_irq (&dev_priv->irq_lock); - } +WARN_ON_ONCE (power_well->data !=PIPE_A ); + +spin_lock_irq (&dev_priv->irq_lock); +valleyview_disable_display_irqs (dev_priv); +spin_unlock_irq (&dev_priv->irq_lock);chv_set_pipe_power_well (dev_priv, power_well, false); -if (power_well->data ==PIPE_A ) -vlv_power_sequencer_reset (dev_priv); +vlv_power_sequencer_reset (dev_priv); }/**
Signature · 6 lines
2.3.6 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 3/9] drm/i915: Simplify CHV pipe A power well code
Quoted 89 lines · On 6/29/2015 5:55 PM, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
The pipe A power well is the "disp2d" well on CHV and pipe B and C wells don't even exist. Thereforce we can remove the checks for pipe A vs. others and just assume it's always pipe A.
Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_runtime_pm.c | 47 ++++++++++++++------------------- 1 file changed, 20 insertions(+), 27 deletions(-)drivers/gpu/drm/i915/intel_runtime_pm.c +20
-27@@ -1042,53 +1042,46 @@ out:static void chv_pipe_power_well_sync_hw (struct drm_i915_private *dev_priv,struct i915_power_well *power_well) { +WARN_ON_ONCE (power_well->data !=PIPE_A ); +chv_set_pipe_power_well (dev_priv, power_well, power_well->count >0 ); }static void chv_pipe_power_well_enable (struct drm_i915_private *dev_priv,struct i915_power_well *power_well) { -WARN_ON_ONCE (power_well->data !=PIPE_A && - power_well->data !=PIPE_B && - power_well->data !=PIPE_C ); +WARN_ON_ONCE (power_well->data !=PIPE_A );chv_set_pipe_power_well (dev_priv, power_well, true); -if (power_well->data ==PIPE_A ) { -spin_lock_irq (&dev_priv->irq_lock); -valleyview_enable_display_irqs (dev_priv); -spin_unlock_irq (&dev_priv->irq_lock); +spin_lock_irq (&dev_priv->irq_lock); +valleyview_enable_display_irqs (dev_priv); +spin_unlock_irq (&dev_priv->irq_lock); -/* -* During driver initialization/resume we can avoid restoring the -* part of the HW/SW state that will be inited anyway explicitly. -*/ -if (dev_priv->power_domains.initializing) -return ; +/* +* During driver initialization/resume we can avoid restoring the +* part of the HW/SW state that will be inited anyway explicitly. +*/ +if (dev_priv->power_domains.initializing) +return ; -intel_hpd_init (dev_priv); +intel_hpd_init (dev_priv); -i915_redisable_vga_power_on (dev_priv->dev); - } +i915_redisable_vga_power_on (dev_priv->dev); }static void chv_pipe_power_well_disable (struct drm_i915_private *dev_priv,struct i915_power_well *power_well) { -WARN_ON_ONCE (power_well->data !=PIPE_A && - power_well->data !=PIPE_B && - power_well->data !=PIPE_C ); - -if (power_well->data ==PIPE_A ) { -spin_lock_irq (&dev_priv->irq_lock); -valleyview_disable_display_irqs (dev_priv); -spin_unlock_irq (&dev_priv->irq_lock); - } +WARN_ON_ONCE (power_well->data !=PIPE_A ); + +spin_lock_irq (&dev_priv->irq_lock); +valleyview_disable_display_irqs (dev_priv); +spin_unlock_irq (&dev_priv->irq_lock);chv_set_pipe_power_well (dev_priv, power_well, false); -if (power_well->data ==PIPE_A ) -vlv_power_sequencer_reset (dev_priv); +vlv_power_sequencer_reset (dev_priv); }/**
Signature · 2 lines
regards, Sivakumar
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 4/9 drm/i915: Refactor VLV display power well init/deinit
In reply to [email protected]From: Ville Syrjälä <[email protected]>
We do the exact same steps around the disp2d/pipe A power well enable/disable on VLV and CHV. Refactor the shared code into some helpers.
Note that this means we now call vlv_power_sequencer_reset() before turning off the power well, whereas before we did it after. That doesn't matter though since vlv_power_sequencer_reset() just resets the power sequencer software tracking and doesn't touch the hardware at all.
--- drivers/gpu/drm/i915/intel_runtime_pm.c | 52 +++++++++++++++------------------ 1 file changed, 23 insertions(+), 29 deletions(-)
drivers/gpu/drm/i915/intel_runtime_pm.c +23 -29
@@ -835,12 +835,8 @@ static bool vlv_power_well_enabled(struct drm_i915_private *dev_priv,return enabled; } -static void vlv_display_power_well_enable (struct drm_i915_private *dev_priv, -struct i915_power_well *power_well) +static void vlv_display_power_well_init (struct drm_i915_private *dev_priv) { -WARN_ON_ONCE (power_well->data !=PUNIT_POWER_WELL_DISP2D ); - -vlv_set_power_well (dev_priv, power_well, true);spin_lock_irq (&dev_priv->irq_lock);valleyview_enable_display_irqs (dev_priv);
@@ -858,18 +854,33 @@ static void vlv_display_power_well_enable(struct drm_i915_private *dev_priv,i915_redisable_vga_power_on (dev_priv->dev); } +static void vlv_display_power_well_deinit (struct drm_i915_private *dev_priv) +{ +spin_lock_irq (&dev_priv->irq_lock); +valleyview_disable_display_irqs (dev_priv); +spin_unlock_irq (&dev_priv->irq_lock); + +vlv_power_sequencer_reset (dev_priv); +} + +static void vlv_display_power_well_enable (struct drm_i915_private *dev_priv, +struct i915_power_well *power_well) +{ +WARN_ON_ONCE (power_well->data !=PUNIT_POWER_WELL_DISP2D ); + +vlv_set_power_well (dev_priv, power_well, true); + +vlv_display_power_well_init (dev_priv); +} +static void vlv_display_power_well_disable (struct drm_i915_private *dev_priv,struct i915_power_well *power_well) {WARN_ON_ONCE (power_well->data !=PUNIT_POWER_WELL_DISP2D ); -spin_lock_irq (&dev_priv->irq_lock); -valleyview_disable_display_irqs (dev_priv); -spin_unlock_irq (&dev_priv->irq_lock); +vlv_display_power_well_deinit (dev_priv);vlv_set_power_well (dev_priv, power_well, false); - -vlv_power_sequencer_reset (dev_priv); } static void vlv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv,
@@ -1054,20 +1065,7 @@ static void chv_pipe_power_well_enable(struct drm_i915_private *dev_priv,chv_set_pipe_power_well (dev_priv, power_well, true); -spin_lock_irq (&dev_priv->irq_lock); -valleyview_enable_display_irqs (dev_priv); -spin_unlock_irq (&dev_priv->irq_lock); - -/* -* During driver initialization/resume we can avoid restoring the -* part of the HW/SW state that will be inited anyway explicitly. -*/ -if (dev_priv->power_domains.initializing) -return ; - -intel_hpd_init (dev_priv); - -i915_redisable_vga_power_on (dev_priv->dev); +vlv_display_power_well_init (dev_priv); } static void chv_pipe_power_well_disable(struct drm_i915_private *dev_priv,
@@ -1075,13 +1073,9 @@ static void chv_pipe_power_well_disable(struct drm_i915_private *dev_priv, {WARN_ON_ONCE (power_well->data !=PIPE_A ); -spin_lock_irq (&dev_priv->irq_lock); -valleyview_disable_display_irqs (dev_priv); -spin_unlock_irq (&dev_priv->irq_lock); +vlv_display_power_well_deinit (dev_priv);chv_set_pipe_power_well (dev_priv, power_well, false); - -vlv_power_sequencer_reset (dev_priv); }/**
Signature · 6 lines
2.3.6 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/9] drm/i915: Refactor VLV display power well init/deinit
Quoted 111 lines · On 6/29/2015 5:55 PM, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
We do the exact same steps around the disp2d/pipe A power well enable/disable on VLV and CHV. Refactor the shared code into some helpers.
Note that this means we now call
vlv_power_sequencer_reset()before turning off the power well, whereas before we did it after. That doesn't matter though sincevlv_power_sequencer_reset()just resets the power sequencer software tracking and doesn't touch the hardware at all.Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_runtime_pm.c | 52 +++++++++++++++------------------ 1 file changed, 23 insertions(+), 29 deletions(-)drivers/gpu/drm/i915/intel_runtime_pm.c +23
-29@@ -835,12 +835,8 @@ static bool vlv_power_well_enabled(struct drm_i915_private *dev_priv,return enabled; } -static void vlv_display_power_well_enable (struct drm_i915_private *dev_priv, -struct i915_power_well *power_well) +static void vlv_display_power_well_init (struct drm_i915_private *dev_priv) { -WARN_ON_ONCE (power_well->data !=PUNIT_POWER_WELL_DISP2D ); - -vlv_set_power_well (dev_priv, power_well, true);spin_lock_irq (&dev_priv->irq_lock);valleyview_enable_display_irqs (dev_priv);@@ -858,18 +854,33 @@ static void vlv_display_power_well_enable(struct drm_i915_private *dev_priv,i915_redisable_vga_power_on (dev_priv->dev); } +static void vlv_display_power_well_deinit (struct drm_i915_private *dev_priv) +{ +spin_lock_irq (&dev_priv->irq_lock); +valleyview_disable_display_irqs (dev_priv); +spin_unlock_irq (&dev_priv->irq_lock); + +vlv_power_sequencer_reset (dev_priv); +} + +static void vlv_display_power_well_enable (struct drm_i915_private *dev_priv, +struct i915_power_well *power_well) +{ +WARN_ON_ONCE (power_well->data !=PUNIT_POWER_WELL_DISP2D ); + +vlv_set_power_well (dev_priv, power_well, true); + +vlv_display_power_well_init (dev_priv); +} +static void vlv_display_power_well_disable (struct drm_i915_private *dev_priv,struct i915_power_well *power_well) {WARN_ON_ONCE (power_well->data !=PUNIT_POWER_WELL_DISP2D ); -spin_lock_irq (&dev_priv->irq_lock); -valleyview_disable_display_irqs (dev_priv); -spin_unlock_irq (&dev_priv->irq_lock); +vlv_display_power_well_deinit (dev_priv);vlv_set_power_well (dev_priv, power_well, false); - -vlv_power_sequencer_reset (dev_priv); } static void vlv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv,@@ -1054,20 +1065,7 @@ static void chv_pipe_power_well_enable(struct drm_i915_private *dev_priv,chv_set_pipe_power_well (dev_priv, power_well, true); -spin_lock_irq (&dev_priv->irq_lock); -valleyview_enable_display_irqs (dev_priv); -spin_unlock_irq (&dev_priv->irq_lock); - -/* -* During driver initialization/resume we can avoid restoring the -* part of the HW/SW state that will be inited anyway explicitly. -*/ -if (dev_priv->power_domains.initializing) -return ; - -intel_hpd_init (dev_priv); - -i915_redisable_vga_power_on (dev_priv->dev); +vlv_display_power_well_init (dev_priv); } static void chv_pipe_power_well_disable(struct drm_i915_private *dev_priv,@@ -1075,13 +1073,9 @@ static void chv_pipe_power_well_disable(struct drm_i915_private *dev_priv, {WARN_ON_ONCE (power_well->data !=PIPE_A ); -spin_lock_irq (&dev_priv->irq_lock); -valleyview_disable_display_irqs (dev_priv); -spin_unlock_irq (&dev_priv->irq_lock); +vlv_display_power_well_deinit (dev_priv);chv_set_pipe_power_well (dev_priv, power_well, false); - -vlv_power_sequencer_reset (dev_priv); }/**
Signature · 2 lines
regards, Sivakumar
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 5/9 drm/i915: Clear out DPLL state from pipe config in DSI get config
In reply to [email protected]From: Ville Syrjälä <[email protected]>
VLV/CHV don't use the DPLL with DSI, so just clear out the DPLL state from the pipe_config in intel_dsi_get_config(). This avoids spurious state checker warnings. We already did it this way for DPLL_MD, but do it for DPLL too.
Toss in a WARN to intel_dsi_pre_enable() to make sure the ref clocks are enabled however. Supposedly they have some meaning to DSI too. We now keep the ref clocks always enabled while the disp2d well is enabled.
--- drivers/gpu/drm/i915/intel_dsi.c | 15 +++++---------- 1 file changed, 5 insertions(+), 10 deletions(-)
drivers/gpu/drm/i915/intel_dsi.c +5 -10
@@ -421,18 +421,12 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* Disable DPOunit clock gating, can stall pipe * and we need DPLL REFA always enabled */ - tmp =I915_READ (DPLL (pipe)); - tmp |=DPLL_REF_CLK_ENABLE_VLV ; -I915_WRITE (DPLL (pipe), tmp); - -/* update the hw state for DPLL */ - intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_REF_CLK_VLV | -DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; - tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;I915_WRITE (DSPCLK_GATE_D , tmp); +WARN_ON ((I915_READ (DPLL (pipe)) &DPLL_REF_CLK_ENABLE_VLV ) ==0 ); +/* put device in ready state */ intel_dsi_device_ready (encoder);
@@ -635,9 +629,10 @@ static void intel_dsi_get_config(struct intel_encoder *encoder,DRM_DEBUG_KMS ("\n" );/* -* DPLL_MD is not used in case of DSI, reading will get some default value -* set dpll_md = 0 +* DPLL is not used in case of DSI, reading will getsome default value. +* Clear the state to keep the state checker happy. */ + pipe_config->dpll_hw_state.dpll =0 ; pipe_config->dpll_hw_state.dpll_md =0 ; pclk =vlv_get_dsi_pclk (encoder, pipe_config->pipe_bpp);
Signature · 6 lines
2.3.6 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/9] drm/i915: Clear out DPLL state from pipe config in DSI get config
Quoted 43 lines · On Mon, Jun 29, 2015 at 03:25:52PM +0300, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
VLV/CHV don't use the DPLL with DSI, so just clear out the DPLL state from the
pipe_configinintel_dsi_get_config(). This avoids spurious state checker warnings. We already did it this way forDPLL_MD, but do it for DPLL too.Toss in a WARN to
intel_dsi_pre_enable()to make sure the ref clocks are enabled however. Supposedly they have some meaning to DSI too. We now keep the ref clocks always enabled while the disp2d well is enabled.Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_dsi.c | 15 +++++---------- 1 file changed, 5 insertions(+), 10 deletions(-)drivers/gpu/drm/i915/intel_dsi.c +2
-8@@ -421,18 +421,12 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* Disable DPOunit clock gating, can stall pipe * and we need DPLL REFA always enabled */ - tmp =I915_READ (DPLL (pipe)); - tmp |=DPLL_REF_CLK_ENABLE_VLV ; -I915_WRITE (DPLL (pipe), tmp); - -/* update the hw state for DPLL */ - intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_REF_CLK_VLV | -DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; - tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;I915_WRITE (DSPCLK_GATE_D , tmp); +WARN_ON ((I915_READ (DPLL (pipe)) &DPLL_REF_CLK_ENABLE_VLV ) ==0 ); +/* put device in ready state */ intel_dsi_device_ready (encoder);
drivers/gpu/drm/i915/intel_dsi.c static void intel_dsi_get_config(struct intel_encoder *encoder, · line 636
Quoted 10 lines
drivers/gpu/drm/i915/intel_dsi.c +3
-2@@ -635,9 +629,10 @@ static void intel_dsi_get_config(struct intel_encoder *encoder,DRM_DEBUG_KMS ("\n" );/* -* DPLL_MD is not used in case of DSI, reading will get some default value -* set dpll_md = 0 +* DPLL is not used in case of DSI, reading will getsome default value. +* Clear the state to keep the state checker happy. */ + pipe_config->dpll_hw_state.dpll =0 ; pipe_config->dpll_hw_state.dpll_md =0 ;
State configs are supposed to be kzallocated. Needing this indicates a pretty serious bug - I'd vote to instead also ditch the dpll_md line and fix the offender.
-Daniel
Quoted 9 lines
drivers/gpu/drm/i915/intel_dsi.c +0
-0pclk =vlv_get_dsi_pclk (encoder, pipe_config->pipe_bpp);Signature · 6 lines
2.3.6 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 7 lines
Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/9] drm/i915: Clear out DPLL state from pipe config in DSI get config
Quoted 46 lines · Daniel Vetter
Quoted 45 lines · On Mon, Jun 29, 2015 at 03:25:52PM +0300, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
VLV/CHV don't use the DPLL with DSI, so just clear out the DPLL state from the
pipe_configinintel_dsi_get_config(). This avoids spurious state checker warnings. We already did it this way forDPLL_MD, but do it for DPLL too.Toss in a WARN to
intel_dsi_pre_enable()to make sure the ref clocks are enabled however. Supposedly they have some meaning to DSI too. We now keep the ref clocks always enabled while the disp2d well is enabled.Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_dsi.c | 15 +++++---------- 1 file changed, 5 insertions(+), 10 deletions(-)drivers/gpu/drm/i915/intel_dsi.c +2
-8@@ -421,18 +421,12 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* Disable DPOunit clock gating, can stall pipe * and we need DPLL REFA always enabled */ - tmp =I915_READ (DPLL (pipe)); - tmp |=DPLL_REF_CLK_ENABLE_VLV ; -I915_WRITE (DPLL (pipe), tmp); - -/* update the hw state for DPLL */ - intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_REF_CLK_VLV | -DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; - tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;I915_WRITE (DSPCLK_GATE_D , tmp); +WARN_ON ((I915_READ (DPLL (pipe)) &DPLL_REF_CLK_ENABLE_VLV ) ==0 ); +/* put device in ready state */ intel_dsi_device_ready (encoder);@@ -635,9 +629,10 @@ static void intel_dsi_get_config(struct intel_encoder *encoder,DRM_DEBUG_KMS ("\n" );
Quoted 12 lines
drivers/gpu/drm/i915/intel_dsi.c static void intel_dsi_get_config(struct intel_encoder *encoder, · line 636
Quoted 8 lines
drivers/gpu/drm/i915/intel_dsi.c +3
-2/* -* DPLL_MD is not used in case of DSI, reading will get some default value -* set dpll_md = 0 +* DPLL is not used in case of DSI, reading will getsome default value. +* Clear the state to keep the state checker happy. */ + pipe_config->dpll_hw_state.dpll =0 ; pipe_config->dpll_hw_state.dpll_md =0 ;State configs are supposed to be kzallocated. Needing this indicates a pretty serious bug - I'd vote to instead also ditch the
dpll_mdline and fix the offender.
There is no offender really. We read out the DPLL state before we know which ports are active and hence can't tell at that point if the information is really relevant.
The alternative would be to explicitly program the DPLL to a specific state for DSI. That is, we could just call {vlv,chv}_disable_pll() from crtc_enable when the pipe is driving a DSI port), and have intel_dsi_compute_config() fill in an identical state.
Quoted 16 lines
-Daniel
Quoted 9 lines
drivers/gpu/drm/i915/intel_dsi.c +0
-0pclk =vlv_get_dsi_pclk (encoder, pipe_config->pipe_bpp);Signature · 6 lines
2.3.6 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfxSignature · 3 lines
Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/9] drm/i915: Clear out DPLL state from pipe config in DSI get config
Quoted 60 lines · Ville Syrjälä
Quoted 46 lines · Daniel Vetter
Quoted 45 lines · On Mon, Jun 29, 2015 at 03:25:52PM +0300, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
VLV/CHV don't use the DPLL with DSI, so just clear out the DPLL state from the
pipe_configinintel_dsi_get_config(). This avoids spurious state checker warnings. We already did it this way forDPLL_MD, but do it for DPLL too.Toss in a WARN to
intel_dsi_pre_enable()to make sure the ref clocks are enabled however. Supposedly they have some meaning to DSI too. We now keep the ref clocks always enabled while the disp2d well is enabled.Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_dsi.c | 15 +++++---------- 1 file changed, 5 insertions(+), 10 deletions(-)drivers/gpu/drm/i915/intel_dsi.c +2
-8@@ -421,18 +421,12 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* Disable DPOunit clock gating, can stall pipe * and we need DPLL REFA always enabled */ - tmp =I915_READ (DPLL (pipe)); - tmp |=DPLL_REF_CLK_ENABLE_VLV ; -I915_WRITE (DPLL (pipe), tmp); - -/* update the hw state for DPLL */ - intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_REF_CLK_VLV | -DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; - tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;I915_WRITE (DSPCLK_GATE_D , tmp); +WARN_ON ((I915_READ (DPLL (pipe)) &DPLL_REF_CLK_ENABLE_VLV ) ==0 ); +/* put device in ready state */ intel_dsi_device_ready (encoder);@@ -635,9 +629,10 @@ static void intel_dsi_get_config(struct intel_encoder *encoder,DRM_DEBUG_KMS ("\n" );Quoted 12 lines
drivers/gpu/drm/i915/intel_dsi.c static void intel_dsi_get_config(struct intel_encoder *encoder, · line 636
Quoted 8 lines
drivers/gpu/drm/i915/intel_dsi.c +3
-2/* -* DPLL_MD is not used in case of DSI, reading will get some default value -* set dpll_md = 0 +* DPLL is not used in case of DSI, reading will getsome default value. +* Clear the state to keep the state checker happy. */ + pipe_config->dpll_hw_state.dpll =0 ; pipe_config->dpll_hw_state.dpll_md =0 ;State configs are supposed to be kzallocated. Needing this indicates a pretty serious bug - I'd vote to instead also ditch the
dpll_mdline and fix the offender.
Quoted 8 lines
There is no offender really. We read out the DPLL state before we know which ports are active and hence can't tell at that point if the information is really relevant.
The alternative would be to explicitly program the DPLL to a specific state for DSI. That is, we could just call {vlv,chv}_disable_pll() from
crtc_enablewhen the pipe is driving a DSI port), and haveintel_dsi_compute_config()fill in an identical state.
Or I suppose we could move clock readout to the encoder .get_config() entirely.
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/9] drm/i915: Clear out DPLL state from pipe config in DSI get config
Quoted 61 lines · Ville Syrjälä
Quoted 60 lines · Ville Syrjälä
Quoted 58 lines · Daniel Vetter
Quoted 43 lines · On Mon, Jun 29, 2015 at 03:25:52PM +0300, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
VLV/CHV don't use the DPLL with DSI, so just clear out the DPLL state from the
pipe_configinintel_dsi_get_config(). This avoids spurious state checker warnings. We already did it this way forDPLL_MD, but do it for DPLL too.Toss in a WARN to
intel_dsi_pre_enable()to make sure the ref clocks are enabled however. Supposedly they have some meaning to DSI too. We now keep the ref clocks always enabled while the disp2d well is enabled.Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_dsi.c | 15 +++++---------- 1 file changed, 5 insertions(+), 10 deletions(-)drivers/gpu/drm/i915/intel_dsi.c +2
-8@@ -421,18 +421,12 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* Disable DPOunit clock gating, can stall pipe * and we need DPLL REFA always enabled */ - tmp =I915_READ (DPLL (pipe)); - tmp |=DPLL_REF_CLK_ENABLE_VLV ; -I915_WRITE (DPLL (pipe), tmp); - -/* update the hw state for DPLL */ - intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_REF_CLK_VLV | -DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; - tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;I915_WRITE (DSPCLK_GATE_D , tmp); +WARN_ON ((I915_READ (DPLL (pipe)) &DPLL_REF_CLK_ENABLE_VLV ) ==0 ); +/* put device in ready state */ intel_dsi_device_ready (encoder);drivers/gpu/drm/i915/intel_dsi.c static void intel_dsi_get_config(struct intel_encoder *encoder, · line 636
Quoted 10 lines
drivers/gpu/drm/i915/intel_dsi.c +3
-2@@ -635,9 +629,10 @@ static void intel_dsi_get_config(struct intel_encoder *encoder,DRM_DEBUG_KMS ("\n" );/* -* DPLL_MD is not used in case of DSI, reading will get some default value -* set dpll_md = 0 +* DPLL is not used in case of DSI, reading will getsome default value. +* Clear the state to keep the state checker happy. */ + pipe_config->dpll_hw_state.dpll =0 ; pipe_config->dpll_hw_state.dpll_md =0 ;State configs are supposed to be kzallocated. Needing this indicates a pretty serious bug - I'd vote to instead also ditch the
dpll_mdline and fix the offender.
Quoted 3 lines
Quoted 3 lines
There is no offender really. We read out the DPLL state before we know which ports are active and hence can't tell at that point if the information is really relevant.
So the bios leaves the DPLL enabled even when using a DSI port? Or do we miss to check some routing bits in get_clock?
Quoted 7 lines
Quoted 4 lines
The alternative would be to explicitly program the DPLL to a specific state for DSI. That is, we could just call {vlv,chv}_disable_pll() from
crtc_enablewhen the pipe is driving a DSI port), and haveintel_dsi_compute_config()fill in an identical state.Or I suppose we could move clock readout to the encoder .get_config() entirely.
Yeah either that or do a crtc sanitize to fixup the DPLL that's somehow enabled but not needed. Either option is imo clearer than cleaning out state that we've read.
-Daniel
Signature · 7 lines
Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/9] drm/i915: Clear out DPLL state from pipe config in DSI get config
Quoted 62 lines · Daniel Vetter
Quoted 61 lines · Ville Syrjälä
Quoted 60 lines · Ville Syrjälä
Quoted 58 lines · Daniel Vetter
Quoted 43 lines · On Mon, Jun 29, 2015 at 03:25:52PM +0300, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
VLV/CHV don't use the DPLL with DSI, so just clear out the DPLL state from the
pipe_configinintel_dsi_get_config(). This avoids spurious state checker warnings. We already did it this way forDPLL_MD, but do it for DPLL too.Toss in a WARN to
intel_dsi_pre_enable()to make sure the ref clocks are enabled however. Supposedly they have some meaning to DSI too. We now keep the ref clocks always enabled while the disp2d well is enabled.Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_dsi.c | 15 +++++---------- 1 file changed, 5 insertions(+), 10 deletions(-)drivers/gpu/drm/i915/intel_dsi.c +2
-8@@ -421,18 +421,12 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* Disable DPOunit clock gating, can stall pipe * and we need DPLL REFA always enabled */ - tmp =I915_READ (DPLL (pipe)); - tmp |=DPLL_REF_CLK_ENABLE_VLV ; -I915_WRITE (DPLL (pipe), tmp); - -/* update the hw state for DPLL */ - intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_REF_CLK_VLV | -DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; - tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;I915_WRITE (DSPCLK_GATE_D , tmp); +WARN_ON ((I915_READ (DPLL (pipe)) &DPLL_REF_CLK_ENABLE_VLV ) ==0 ); +/* put device in ready state */ intel_dsi_device_ready (encoder);drivers/gpu/drm/i915/intel_dsi.c static void intel_dsi_get_config(struct intel_encoder *encoder, · line 636
Quoted 10 lines
drivers/gpu/drm/i915/intel_dsi.c +3
-2@@ -635,9 +629,10 @@ static void intel_dsi_get_config(struct intel_encoder *encoder,DRM_DEBUG_KMS ("\n" );/* -* DPLL_MD is not used in case of DSI, reading will get some default value -* set dpll_md = 0 +* DPLL is not used in case of DSI, reading will getsome default value. +* Clear the state to keep the state checker happy. */ + pipe_config->dpll_hw_state.dpll =0 ; pipe_config->dpll_hw_state.dpll_md =0 ;State configs are supposed to be kzallocated. Needing this indicates a pretty serious bug - I'd vote to instead also ditch the
dpll_mdline and fix the offender.
Quoted 6 lines
Quoted 3 lines
Quoted 3 lines
There is no offender really. We read out the DPLL state before we know which ports are active and hence can't tell at that point if the information is really relevant.
So the bios leaves the DPLL enabled even when using a DSI port? Or do we miss to check some routing bits in
get_clock?
Not necessarily enabled, but there are other bits in there that could be left in any state basically. The DSI port simply doesn't care.
Quoted 10 lines
Quoted 7 lines
Quoted 4 lines
The alternative would be to explicitly program the DPLL to a specific state for DSI. That is, we could just call {vlv,chv}_disable_pll() from
crtc_enablewhen the pipe is driving a DSI port), and haveintel_dsi_compute_config()fill in an identical state.Or I suppose we could move clock readout to the encoder .get_config() entirely.
Yeah either that or do a crtc sanitize to fixup the DPLL that's somehow enabled but not needed.
To do that properly we should just expose all the PLLs as "shared" PLLs. I don't really want to add a VLV/CHV specific hack for that.
Quoted 7 lines
Either option is imo clearer than cleaning out
state that we've read.
-DanielSignature · 3 lines
Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/9] drm/i915: Clear out DPLL state from pipe config in DSI get config
Quoted 67 lines · Ville Syrjälä
Quoted 66 lines · Daniel Vetter
Quoted 64 lines · Ville Syrjälä
Quoted 63 lines · Ville Syrjälä
Quoted 46 lines · Daniel Vetter
Quoted 45 lines · On Mon, Jun 29, 2015 at 03:25:52PM +0300, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
VLV/CHV don't use the DPLL with DSI, so just clear out the DPLL state from the
pipe_configinintel_dsi_get_config(). This avoids spurious state checker warnings. We already did it this way forDPLL_MD, but do it for DPLL too.Toss in a WARN to
intel_dsi_pre_enable()to make sure the ref clocks are enabled however. Supposedly they have some meaning to DSI too. We now keep the ref clocks always enabled while the disp2d well is enabled.Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_dsi.c | 15 +++++---------- 1 file changed, 5 insertions(+), 10 deletions(-)drivers/gpu/drm/i915/intel_dsi.c +2
-8@@ -421,18 +421,12 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* Disable DPOunit clock gating, can stall pipe * and we need DPLL REFA always enabled */ - tmp =I915_READ (DPLL (pipe)); - tmp |=DPLL_REF_CLK_ENABLE_VLV ; -I915_WRITE (DPLL (pipe), tmp); - -/* update the hw state for DPLL */ - intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_REF_CLK_VLV | -DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; - tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;I915_WRITE (DSPCLK_GATE_D , tmp); +WARN_ON ((I915_READ (DPLL (pipe)) &DPLL_REF_CLK_ENABLE_VLV ) ==0 ); +/* put device in ready state */ intel_dsi_device_ready (encoder);@@ -635,9 +629,10 @@ static void intel_dsi_get_config(struct intel_encoder *encoder,DRM_DEBUG_KMS ("\n" );Quoted 12 lines
drivers/gpu/drm/i915/intel_dsi.c static void intel_dsi_get_config(struct intel_encoder *encoder, · line 636
Quoted 8 lines
drivers/gpu/drm/i915/intel_dsi.c +3
-2/* -* DPLL_MD is not used in case of DSI, reading will get some default value -* set dpll_md = 0 +* DPLL is not used in case of DSI, reading will getsome default value. +* Clear the state to keep the state checker happy. */ + pipe_config->dpll_hw_state.dpll =0 ; pipe_config->dpll_hw_state.dpll_md =0 ;State configs are supposed to be kzallocated. Needing this indicates a pretty serious bug - I'd vote to instead also ditch the
dpll_mdline and fix the offender.There is no offender really. We read out the DPLL state before we know which ports are active and hence can't tell at that point if the information is really relevant.
Quoted 5 lines
Quoted 2 lines
So the bios leaves the DPLL enabled even when using a DSI port? Or do we miss to check some routing bits in
get_clock?Not necessarily enabled, but there are other bits in there that could be left in any state basically. The DSI port simply doesn't care.
If the enable bit is what's gating things here then we should just forgo reading out any dpll register state if that's not set. Looking at the vlv/chv state readout code that seems to be the trouble - there's nothing guarding the register reads into the pipe_config at all. Didn't matter pre-vlv without dsi since enable pipe should imply enabled dpll, but obviously won't work correctly with dsi. Can you please spin such a patch and remove the hacks here from dsi_get_config?
-Daniel
Signature · 7 lines
Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/9] drm/i915: Clear out DPLL state from pipe config in DSI get config
Quoted 69 lines · Daniel Vetter
Quoted 61 lines · Ville Syrjälä
Quoted 60 lines · Daniel Vetter
Quoted 59 lines · Ville Syrjälä
Quoted 58 lines · Ville Syrjälä
Quoted 57 lines · Daniel Vetter
Quoted 43 lines · On Mon, Jun 29, 2015 at 03:25:52PM +0300, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
VLV/CHV don't use the DPLL with DSI, so just clear out the DPLL state from the
pipe_configinintel_dsi_get_config(). This avoids spurious state checker warnings. We already did it this way forDPLL_MD, but do it for DPLL too.Toss in a WARN to
intel_dsi_pre_enable()to make sure the ref clocks are enabled however. Supposedly they have some meaning to DSI too. We now keep the ref clocks always enabled while the disp2d well is enabled.Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_dsi.c | 15 +++++---------- 1 file changed, 5 insertions(+), 10 deletions(-)drivers/gpu/drm/i915/intel_dsi.c +2
-8@@ -421,18 +421,12 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* Disable DPOunit clock gating, can stall pipe * and we need DPLL REFA always enabled */ - tmp =I915_READ (DPLL (pipe)); - tmp |=DPLL_REF_CLK_ENABLE_VLV ; -I915_WRITE (DPLL (pipe), tmp); - -/* update the hw state for DPLL */ - intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_REF_CLK_VLV | -DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; - tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;I915_WRITE (DSPCLK_GATE_D , tmp); +WARN_ON ((I915_READ (DPLL (pipe)) &DPLL_REF_CLK_ENABLE_VLV ) ==0 ); +/* put device in ready state */ intel_dsi_device_ready (encoder);drivers/gpu/drm/i915/intel_dsi.c static void intel_dsi_get_config(struct intel_encoder *encoder, · line 636
Quoted 10 lines
drivers/gpu/drm/i915/intel_dsi.c +3
-2@@ -635,9 +629,10 @@ static void intel_dsi_get_config(struct intel_encoder *encoder,DRM_DEBUG_KMS ("\n" );/* -* DPLL_MD is not used in case of DSI, reading will get some default value -* set dpll_md = 0 +* DPLL is not used in case of DSI, reading will getsome default value. +* Clear the state to keep the state checker happy. */ + pipe_config->dpll_hw_state.dpll =0 ; pipe_config->dpll_hw_state.dpll_md =0 ;State configs are supposed to be kzallocated. Needing this indicates a pretty serious bug - I'd vote to instead also ditch the
dpll_mdline and fix the offender.Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
Quoted 3 lines
There is no offender really. We read out the DPLL state before we know which ports are active and hence can't tell at that point if the information is really relevant.
So the bios leaves the DPLL enabled even when using a DSI port? Or do we miss to check some routing bits in
get_clock?Not necessarily enabled, but there are other bits in there that could be left in any state basically. The DSI port simply doesn't care.
Quoted 8 lines
If the enable bit is what's gating things here then we should just forgo reading out any dpll register state if that's not set. Looking at the vlv/chv state readout code that seems to be the trouble - there's nothing guarding the register reads into the
pipe_configat all. Didn't matter pre-vlv without dsi since enable pipe should imply enabled dpll, but obviously won't work correctly with dsi. Can you please spin such a patch and remove the hacks here fromdsi_get_config?
-Daniel
Not sure i understand the point of contention here, just noticed this after i gave my RB :) so my justification on why this is proper is that DSI is not supposed to touch DPLL register any place we access dpll_hw_state.dpll is under !is_dsi check so that ensures that we dont program DPLL register for dsi panel. it was wrong to have originally modfied DPLL register inside intel_dsi_pre_enable so removal is fine. setting it to zero in intel_dsi_get_config is of no impact since any place we write back the contents of dpll_hw_state is past the !is_dsi check is never consumed by anyone as long as the CRTC uses DSI.
Signature · 7 lines
regards, Sivakumar _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/9] drm/i915: Clear out DPLL state from pipe config in DSI get config
Quoted 76 lines · Sivakumar Thulasimani
Quoted 65 lines · Daniel Vetter
Quoted 57 lines · Ville Syrjälä
Quoted 56 lines · Daniel Vetter
Quoted 55 lines · Ville Syrjälä
Quoted 54 lines · Ville Syrjälä
Quoted 53 lines · Daniel Vetter
Quoted 40 lines · On Mon, Jun 29, 2015 at 03:25:52PM +0300, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
VLV/CHV don't use the DPLL with DSI, so just clear out the DPLL state from the
pipe_configinintel_dsi_get_config(). This avoids spurious state checker warnings. We already did it this way forDPLL_MD, but do it for DPLL too.Toss in a WARN to
intel_dsi_pre_enable()to make sure the ref clocks are enabled however. Supposedly they have some meaning to DSI too. We now keep the ref clocks always enabled while the disp2d well is enabled.Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_dsi.c | 15 +++++---------- 1 file changed, 5 insertions(+), 10 deletions(-)drivers/gpu/drm/i915/intel_dsi.c +2
-8@@ -421,18 +421,12 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* Disable DPOunit clock gating, can stall pipe * and we need DPLL REFA always enabled */ - tmp =I915_READ (DPLL (pipe)); - tmp |=DPLL_REF_CLK_ENABLE_VLV ; -I915_WRITE (DPLL (pipe), tmp); - -/* update the hw state for DPLL */ - intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_REF_CLK_VLV | -DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; - tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;I915_WRITE (DSPCLK_GATE_D , tmp); +WARN_ON ((I915_READ (DPLL (pipe)) &DPLL_REF_CLK_ENABLE_VLV ) ==0 ); +/* put device in ready state */ intel_dsi_device_ready (encoder);drivers/gpu/drm/i915/intel_dsi.c static void intel_dsi_get_config(struct intel_encoder *encoder, · line 635
Quoted 9 lines
drivers/gpu/drm/i915/intel_dsi.c +3
-2@@ -635,9 +629,10 @@ static void intel_dsi_get_config(struct intel_encoder *encoder,DRM_DEBUG_KMS ("\n" );/* -* DPLL_MD is not used in case of DSI, reading will get some default value -* set dpll_md = 0 +* DPLL is not used in case of DSI, reading will getsome default value. +* Clear the state to keep the state checker happy. */ + pipe_config->dpll_hw_state.dpll =0 ; pipe_config->dpll_hw_state.dpll_md =0 ;State configs are supposed to be kzallocated. Needing this indicates a pretty serious bug - I'd vote to instead also ditch the
dpll_mdline and fix the offender.Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
Quoted 3 lines
There is no offender really. We read out the DPLL state before we know which ports are active and hence can't tell at that point if the information is really relevant.
So the bios leaves the DPLL enabled even when using a DSI port? Or do we miss to check some routing bits in
get_clock?Not necessarily enabled, but there are other bits in there that could be left in any state basically. The DSI port simply doesn't care.
Quoted 8 lines
If the enable bit is what's gating things here then we should just forgo reading out any dpll register state if that's not set. Looking at the vlv/chv state readout code that seems to be the trouble - there's nothing guarding the register reads into the
pipe_configat all. Didn't matter pre-vlv without dsi since enable pipe should imply enabled dpll, but obviously won't work correctly with dsi. Can you please spin such a patch and remove the hacks here fromdsi_get_config?
-Daniel
Quoted 13 lines
Not sure i understand the point of contention here, just noticed this after i gave my RB :)
so my justification on why this is proper is that DSI is not supposed to touch DPLL register
any place we access dpll_hw_state.dpll is under !is_dsi check so that ensures that we dont
program DPLL register for dsi panel. it was wrong to have originally modfied DPLL register
insideintel_dsi_pre_enableso removal is fine. setting it to zero inintel_dsi_get_config
is of no impact since any place we write back the contents ofdpll_hw_stateis past the
!is_dsi check is never consumed by anyone as long as the CRTC uses DSI.
Ok, let's try a patch. Does the below work y/n? I've merged the patches up to this one to dinq meanwhile, but I'd really like to close this first. If it works I can rebase this patch here myself. Diff below is based on -nightly with the above patch, so if you want to test on top of it you also have to remove the dpll = 0; line too ofc.
Thanks, Daniel
drivers/gpu/drm/i915/intel_display.c +4 -0
@@ -8079,6 +8079,10 @@ static bool i9xx_get_pipe_config(struct intel_crtc *crtc,i9xx_get_pfit_config (crtc, pipe_config); + tmp =I915_READ (DPLL (crtc->pipe)); +if (!(tmp &DPLL_VCO_ENABLE )) +return true; +if (INTEL_INFO (dev)->gen >=4 ) { tmp =I915_READ (DPLL_MD (crtc->pipe)); pipe_config->pixel_multiplier =
drivers/gpu/drm/i915/intel_dsi.c +0 -6
@@ -621,12 +621,6 @@ static void intel_dsi_get_config(struct intel_encoder *encoder,u32 pclk;DRM_DEBUG_KMS ("\n" ); -/* -* DPLL_MD is not used in case of DSI, reading will get some default value -* set dpll_md = 0 -*/ - pipe_config->dpll_hw_state.dpll_md =0 ; - pclk =vlv_get_dsi_pclk (encoder, pipe_config->pipe_bpp);if (!pclk)return ;
Signature · 7 lines
Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/9] drm/i915: Clear out DPLL state from pipe config in DSI get config
Quoted 119 lines · Daniel Vetter
Quoted 75 lines · Sivakumar Thulasimani
Quoted 65 lines · Daniel Vetter
Quoted 57 lines · Ville Syrjälä
Quoted 56 lines · Daniel Vetter
Quoted 55 lines · Ville Syrjälä
Quoted 54 lines · Ville Syrjälä
Quoted 53 lines · Daniel Vetter
Quoted 40 lines · On Mon, Jun 29, 2015 at 03:25:52PM +0300, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
VLV/CHV don't use the DPLL with DSI, so just clear out the DPLL state from the
pipe_configinintel_dsi_get_config(). This avoids spurious state checker warnings. We already did it this way forDPLL_MD, but do it for DPLL too.Toss in a WARN to
intel_dsi_pre_enable()to make sure the ref clocks are enabled however. Supposedly they have some meaning to DSI too. We now keep the ref clocks always enabled while the disp2d well is enabled.Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_dsi.c | 15 +++++---------- 1 file changed, 5 insertions(+), 10 deletions(-)drivers/gpu/drm/i915/intel_dsi.c +2
-8@@ -421,18 +421,12 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* Disable DPOunit clock gating, can stall pipe * and we need DPLL REFA always enabled */ - tmp =I915_READ (DPLL (pipe)); - tmp |=DPLL_REF_CLK_ENABLE_VLV ; -I915_WRITE (DPLL (pipe), tmp); - -/* update the hw state for DPLL */ - intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_REF_CLK_VLV | -DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; - tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;I915_WRITE (DSPCLK_GATE_D , tmp); +WARN_ON ((I915_READ (DPLL (pipe)) &DPLL_REF_CLK_ENABLE_VLV ) ==0 ); +/* put device in ready state */ intel_dsi_device_ready (encoder);drivers/gpu/drm/i915/intel_dsi.c static void intel_dsi_get_config(struct intel_encoder *encoder, · line 635
Quoted 9 lines
drivers/gpu/drm/i915/intel_dsi.c +3
-2@@ -635,9 +629,10 @@ static void intel_dsi_get_config(struct intel_encoder *encoder,DRM_DEBUG_KMS ("\n" );/* -* DPLL_MD is not used in case of DSI, reading will get some default value -* set dpll_md = 0 +* DPLL is not used in case of DSI, reading will getsome default value. +* Clear the state to keep the state checker happy. */ + pipe_config->dpll_hw_state.dpll =0 ; pipe_config->dpll_hw_state.dpll_md =0 ;State configs are supposed to be kzallocated. Needing this indicates a pretty serious bug - I'd vote to instead also ditch the
dpll_mdline and fix the offender.Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
Quoted 3 lines
There is no offender really. We read out the DPLL state before we know which ports are active and hence can't tell at that point if the information is really relevant.
So the bios leaves the DPLL enabled even when using a DSI port? Or do we miss to check some routing bits in
get_clock?Not necessarily enabled, but there are other bits in there that could be left in any state basically. The DSI port simply doesn't care.
Quoted 8 lines
If the enable bit is what's gating things here then we should just forgo reading out any dpll register state if that's not set. Looking at the vlv/chv state readout code that seems to be the trouble - there's nothing guarding the register reads into the
pipe_configat all. Didn't matter pre-vlv without dsi since enable pipe should imply enabled dpll, but obviously won't work correctly with dsi. Can you please spin such a patch and remove the hacks here fromdsi_get_config?
-DanielQuoted 13 lines
Not sure i understand the point of contention here, just noticed this after i gave my RB :)
so my justification on why this is proper is that DSI is not supposed to touch DPLL register
any place we access dpll_hw_state.dpll is under !is_dsi check so that ensures that we dont
program DPLL register for dsi panel. it was wrong to have originally modfied DPLL register
insideintel_dsi_pre_enableso removal is fine. setting it to zero inintel_dsi_get_config
is of no impact since any place we write back the contents ofdpll_hw_stateis past the
!is_dsi check is never consumed by anyone as long as the CRTC uses DSI.Ok, let's try a patch. Does the below work y/n? I've merged the patches up to this one to dinq meanwhile, but I'd really like to close this first. If it works I can rebase this patch here myself. Diff below is based on -nightly with the above patch, so if you want to test on top of it you also have to remove the dpll = 0; line too ofc.
Thanks, Daniel
drivers/gpu/drm/i915/intel_display.c +4
-0@@ -8079,6 +8079,10 @@ static bool i9xx_get_pipe_config(struct intel_crtc *crtc,i9xx_get_pfit_config (crtc, pipe_config); + tmp =I915_READ (DPLL (crtc->pipe)); +if (!(tmp &DPLL_VCO_ENABLE )) +return true; +if (INTEL_INFO (dev)->gen >=4 ) { tmp =I915_READ (DPLL_MD (crtc->pipe)); pipe_config->pixel_multiplier =drivers/gpu/drm/i915/intel_dsi.c +0
-0@@ -621,12 +621,6 @@ static void intel_dsi_get_config(struct intel_encoder *encoder,u32 pclk;DRM_DEBUG_KMS ("\n" );
drivers/gpu/drm/i915/intel_dsi.c static void intel_dsi_get_config(struct intel_encoder *encoder, · line 626
Quoted 10 lines
drivers/gpu/drm/i915/intel_dsi.c +0
-6-/* -* DPLL_MD is not used in case of DSI, reading will get some default value -* set dpll_md = 0 -*/ - pipe_config->dpll_hw_state.dpll_md =0 ; - pclk =vlv_get_dsi_pclk (encoder, pipe_config->pipe_bpp);if (!pclk)return ;
i am fine with this patch.
Signature · 7 lines
regards, Sivakumar _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/9] drm/i915: Clear out DPLL state from pipe config in DSI get config
Quoted 122 lines · Sivakumar Thulasimani
Quoted 119 lines · Daniel Vetter
Quoted 75 lines · Sivakumar Thulasimani
Quoted 65 lines · Daniel Vetter
Quoted 57 lines · Ville Syrjälä
Quoted 56 lines · Daniel Vetter
Quoted 55 lines · Ville Syrjälä
Quoted 54 lines · Ville Syrjälä
Quoted 53 lines · Daniel Vetter
Quoted 40 lines · On Mon, Jun 29, 2015 at 03:25:52PM +0300, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
VLV/CHV don't use the DPLL with DSI, so just clear out the DPLL state from the
pipe_configinintel_dsi_get_config(). This avoids spurious state checker warnings. We already did it this way forDPLL_MD, but do it for DPLL too.Toss in a WARN to
intel_dsi_pre_enable()to make sure the ref clocks are enabled however. Supposedly they have some meaning to DSI too. We now keep the ref clocks always enabled while the disp2d well is enabled.Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_dsi.c | 15 +++++---------- 1 file changed, 5 insertions(+), 10 deletions(-)drivers/gpu/drm/i915/intel_dsi.c +2
-8@@ -421,18 +421,12 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* Disable DPOunit clock gating, can stall pipe * and we need DPLL REFA always enabled */ - tmp =I915_READ (DPLL (pipe)); - tmp |=DPLL_REF_CLK_ENABLE_VLV ; -I915_WRITE (DPLL (pipe), tmp); - -/* update the hw state for DPLL */ - intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_REF_CLK_VLV | -DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; - tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;I915_WRITE (DSPCLK_GATE_D , tmp); +WARN_ON ((I915_READ (DPLL (pipe)) &DPLL_REF_CLK_ENABLE_VLV ) ==0 ); +/* put device in ready state */ intel_dsi_device_ready (encoder);drivers/gpu/drm/i915/intel_dsi.c static void intel_dsi_get_config(struct intel_encoder *encoder, · line 635
Quoted 9 lines
drivers/gpu/drm/i915/intel_dsi.c +3
-2@@ -635,9 +629,10 @@ static void intel_dsi_get_config(struct intel_encoder *encoder,DRM_DEBUG_KMS ("\n" );/* -* DPLL_MD is not used in case of DSI, reading will get some default value -* set dpll_md = 0 +* DPLL is not used in case of DSI, reading will getsome default value. +* Clear the state to keep the state checker happy. */ + pipe_config->dpll_hw_state.dpll =0 ; pipe_config->dpll_hw_state.dpll_md =0 ;State configs are supposed to be kzallocated. Needing this indicates a pretty serious bug - I'd vote to instead also ditch the
dpll_mdline and fix the offender.Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
Quoted 3 lines
There is no offender really. We read out the DPLL state before we know which ports are active and hence can't tell at that point if the information is really relevant.
So the bios leaves the DPLL enabled even when using a DSI port? Or do we miss to check some routing bits in
get_clock?Not necessarily enabled, but there are other bits in there that could be left in any state basically. The DSI port simply doesn't care.
Quoted 8 lines
If the enable bit is what's gating things here then we should just forgo reading out any dpll register state if that's not set. Looking at the vlv/chv state readout code that seems to be the trouble - there's nothing guarding the register reads into the
pipe_configat all. Didn't matter pre-vlv without dsi since enable pipe should imply enabled dpll, but obviously won't work correctly with dsi. Can you please spin such a patch and remove the hacks here fromdsi_get_config?
-DanielQuoted 13 lines
Not sure i understand the point of contention here, just noticed this after i gave my RB :)
so my justification on why this is proper is that DSI is not supposed to touch DPLL register
any place we access dpll_hw_state.dpll is under !is_dsi check so that ensures that we dont
program DPLL register for dsi panel. it was wrong to have originally modfied DPLL register
insideintel_dsi_pre_enableso removal is fine. setting it to zero inintel_dsi_get_config
is of no impact since any place we write back the contents ofdpll_hw_stateis past the
!is_dsi check is never consumed by anyone as long as the CRTC uses DSI.Ok, let's try a patch. Does the below work y/n? I've merged the patches up to this one to dinq meanwhile, but I'd really like to close this first. If it works I can rebase this patch here myself. Diff below is based on -nightly with the above patch, so if you want to test on top of it you also have to remove the dpll = 0; line too ofc.
Thanks, Daniel
drivers/gpu/drm/i915/intel_display.c +4
-0@@ -8079,6 +8079,10 @@ static bool i9xx_get_pipe_config(struct intel_crtc *crtc,i9xx_get_pfit_config (crtc, pipe_config); + tmp =I915_READ (DPLL (crtc->pipe)); +if (!(tmp &DPLL_VCO_ENABLE )) +return true; +if (INTEL_INFO (dev)->gen >=4 ) { tmp =I915_READ (DPLL_MD (crtc->pipe)); pipe_config->pixel_multiplier =drivers/gpu/drm/i915/intel_dsi.c +0
-2@@ -621,12 +621,6 @@ static void intel_dsi_get_config(struct intel_encoder *encoder,u32 pclk;DRM_DEBUG_KMS ("\n" ); -/* -* DPLL_MD is not used in case of DSI, reading will get some default value
Quoted 8 lines
drivers/gpu/drm/i915/intel_dsi.c static void intel_dsi_get_config(struct intel_encoder *encoder, · line 626
Quoted 7 lines
drivers/gpu/drm/i915/intel_dsi.c +0
-4-* set dpll_md = 0 -*/ - pipe_config->dpll_hw_state.dpll_md =0 ; - pclk =vlv_get_dsi_pclk (encoder, pipe_config->pipe_bpp);if (!pclk)return ;i am fine with this patch.
Is that a tested-by/reviewed-by? I don't have a byt nor cht here, so this is completely untested.
-Daniel
Signature · 7 lines
Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/9] drm/i915: Clear out DPLL state from pipe config in DSI get config
In reply to [email protected]Quoted 55 lines · On 6/29/2015 5:55 PM, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
VLV/CHV don't use the DPLL with DSI, so just clear out the DPLL state from the
pipe_configinintel_dsi_get_config(). This avoids spurious state checker warnings. We already did it this way forDPLL_MD, but do it for DPLL too.Toss in a WARN to
intel_dsi_pre_enable()to make sure the ref clocks are enabled however. Supposedly they have some meaning to DSI too. We now keep the ref clocks always enabled while the disp2d well is enabled.Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_dsi.c | 15 +++++---------- 1 file changed, 5 insertions(+), 10 deletions(-)drivers/gpu/drm/i915/intel_dsi.c +5
-10@@ -421,18 +421,12 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)/* Disable DPOunit clock gating, can stall pipe * and we need DPLL REFA always enabled */ - tmp =I915_READ (DPLL (pipe)); - tmp |=DPLL_REF_CLK_ENABLE_VLV ; -I915_WRITE (DPLL (pipe), tmp); - -/* update the hw state for DPLL */ - intel_crtc->config->dpll_hw_state.dpll =DPLL_INTEGRATED_REF_CLK_VLV | -DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; - tmp =I915_READ (DSPCLK_GATE_D ); tmp |=DPOUNIT_CLOCK_GATE_DISABLE ;I915_WRITE (DSPCLK_GATE_D , tmp); +WARN_ON ((I915_READ (DPLL (pipe)) &DPLL_REF_CLK_ENABLE_VLV ) ==0 ); +/* put device in ready state */ intel_dsi_device_ready (encoder);@@ -635,9 +629,10 @@ static void intel_dsi_get_config(struct intel_encoder *encoder,DRM_DEBUG_KMS ("\n" );/* -* DPLL_MD is not used in case of DSI, reading will get some default value -* set dpll_md = 0 +* DPLL is not used in case of DSI, reading will getsome default value. +* Clear the state to keep the state checker happy. */ + pipe_config->dpll_hw_state.dpll =0 ; pipe_config->dpll_hw_state.dpll_md =0 ; pclk =vlv_get_dsi_pclk (encoder, pipe_config->pipe_bpp);
Signature · 2 lines
regards, Sivakumar
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 6/9 drm/i915: Move DPLL ref/cri/VGA mode frobbing to the disp2d well enable
In reply to [email protected]From: Ville Syrjälä <[email protected]>
Bunch of stuff needs the DPLL ref/cri clocks on both VLV and CHV, and having VGA mode enabled causes some problems for CHV. So let's just pull the code to configure those bits into the disp2d well enable hook. With the DPLL disable code also fixed to leave those bits alone we should now have a consistent DPLL state all the time even if the DPLL is disabled.
This also neatly removes some duplicated code between the VLV and CHV codepaths.
--- drivers/gpu/drm/i915/intel_runtime_pm.c | 45 ++++++++++++++++++--------------- 1 file changed, 24 insertions(+), 21 deletions(-)
drivers/gpu/drm/i915/intel_runtime_pm.c +24 -21
@@ -837,6 +837,25 @@ static bool vlv_power_well_enabled(struct drm_i915_private *dev_priv,static void vlv_display_power_well_init (struct drm_i915_private *dev_priv) { +enum pipe pipe; + +/* +* Enable the CRI clock source so we can get at the +* display and the reference clock for VGA +* hotplug / manual detection. Supposedly DSI also +* needs the ref clock up and running. +* +* CHV DPLL B/C have some issues if VGA mode is enabled. +*/ +for_each_pipe (dev_priv->dev, pipe) { +u32 val =I915_READ (DPLL (pipe)); + + val |=DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; +if (pipe !=PIPE_A ) + val |=DPLL_INTEGRATED_CRI_CLK_VLV ; + +I915_WRITE (DPLL (pipe), val); + }spin_lock_irq (&dev_priv->irq_lock);valleyview_enable_display_irqs (dev_priv);
@@ -888,13 +907,7 @@ static void vlv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv, {WARN_ON_ONCE (power_well->data !=PUNIT_POWER_WELL_DPIO_CMN_BC ); -/* -* Enable the CRI clock source so we can get at the -* display and the reference clock for VGA -* hotplug / manual detection. -*/ -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS | -DPLL_REF_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); +/* since ref/cri clock was enabled */ udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */ vlv_set_power_well (dev_priv, power_well, true);
@@ -937,22 +950,12 @@ static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv,WARN_ON_ONCE (power_well->data !=PUNIT_POWER_WELL_DPIO_CMN_BC && power_well->data !=PUNIT_POWER_WELL_DPIO_CMN_D ); -/* -* Enable the CRI clock source so we can get at the -* display and the reference clock for VGA -* hotplug / manual detection. -*/ -if (power_well->data ==PUNIT_POWER_WELL_DPIO_CMN_BC ) { +if (power_well->data ==PUNIT_POWER_WELL_DPIO_CMN_BC ) phy =DPIO_PHY0 ; -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS | -DPLL_REF_CLK_ENABLE_VLV ); -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS | -DPLL_REF_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); - }else { +else phy =DPIO_PHY1 ; -I915_WRITE (DPLL (PIPE_C ),I915_READ (DPLL (PIPE_C )) |DPLL_VGA_MODE_DIS | -DPLL_REF_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); - } + +/* since ref/cri clock was enabled */ udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */ vlv_set_power_well (dev_priv, power_well, true);
Signature · 6 lines
2.3.6 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 6/9] drm/i915: Move DPLL ref/cri/VGA mode frobbing to the disp2d well enable
Quoted 89 lines · On 6/29/2015 5:55 PM, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
Bunch of stuff needs the DPLL ref/cri clocks on both VLV and CHV, and having VGA mode enabled causes some problems for CHV. So let's just pull the code to configure those bits into the disp2d well enable hook. With the DPLL disable code also fixed to leave those bits alone we should now have a consistent DPLL state all the time even if the DPLL is disabled.
This also neatly removes some duplicated code between the VLV and CHV codepaths.
Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_runtime_pm.c | 45 ++++++++++++++++++--------------- 1 file changed, 24 insertions(+), 21 deletions(-)drivers/gpu/drm/i915/intel_runtime_pm.c +24
-21@@ -837,6 +837,25 @@ static bool vlv_power_well_enabled(struct drm_i915_private *dev_priv,static void vlv_display_power_well_init (struct drm_i915_private *dev_priv) { +enum pipe pipe; + +/* +* Enable the CRI clock source so we can get at the +* display and the reference clock for VGA +* hotplug / manual detection. Supposedly DSI also +* needs the ref clock up and running. +* +* CHV DPLL B/C have some issues if VGA mode is enabled. +*/ +for_each_pipe (dev_priv->dev, pipe) { +u32 val =I915_READ (DPLL (pipe)); + + val |=DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; +if (pipe !=PIPE_A ) + val |=DPLL_INTEGRATED_CRI_CLK_VLV ; + +I915_WRITE (DPLL (pipe), val); + }spin_lock_irq (&dev_priv->irq_lock);valleyview_enable_display_irqs (dev_priv);@@ -888,13 +907,7 @@ static void vlv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv, {WARN_ON_ONCE (power_well->data !=PUNIT_POWER_WELL_DPIO_CMN_BC ); -/* -* Enable the CRI clock source so we can get at the -* display and the reference clock for VGA -* hotplug / manual detection. -*/ -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS | -DPLL_REF_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); +/* since ref/cri clock was enabled */ udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */ vlv_set_power_well (dev_priv, power_well, true);@@ -937,22 +950,12 @@ static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv,WARN_ON_ONCE (power_well->data !=PUNIT_POWER_WELL_DPIO_CMN_BC && power_well->data !=PUNIT_POWER_WELL_DPIO_CMN_D ); -/* -* Enable the CRI clock source so we can get at the -* display and the reference clock for VGA -* hotplug / manual detection. -*/ -if (power_well->data ==PUNIT_POWER_WELL_DPIO_CMN_BC ) { +if (power_well->data ==PUNIT_POWER_WELL_DPIO_CMN_BC ) phy =DPIO_PHY0 ; -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS | -DPLL_REF_CLK_ENABLE_VLV ); -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS | -DPLL_REF_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); - }else { +else phy =DPIO_PHY1 ; -I915_WRITE (DPLL (PIPE_C ),I915_READ (DPLL (PIPE_C )) |DPLL_VGA_MODE_DIS | -DPLL_REF_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); - } + +/* since ref/cri clock was enabled */ udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */ vlv_set_power_well (dev_priv, power_well, true);
Signature · 2 lines
regards, Sivakumar
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Daniel Vetter
AppliedRe: [PATCH 6/9] drm/i915: Move DPLL ref/cri/VGA mode frobbing to the disp2d well enable
Queued for -next to resolve conflicts in another series, thanks for the patch. -Daniel
Quoted 98 lines · Sivakumar Thulasimani
Reviewed-by Sivakumar Thulasimani <[email protected]>Quoted 83 lines · On 6/29/2015 5:55 PM, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
Bunch of stuff needs the DPLL ref/cri clocks on both VLV and CHV, and having VGA mode enabled causes some problems for CHV. So let's just pull the code to configure those bits into the disp2d well enable hook. With the DPLL disable code also fixed to leave those bits alone we should now have a consistent DPLL state all the time even if the DPLL is disabled.
This also neatly removes some duplicated code between the VLV and CHV codepaths.
Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_runtime_pm.c | 45 ++++++++++++++++++--------------- 1 file changed, 24 insertions(+), 21 deletions(-)drivers/gpu/drm/i915/intel_runtime_pm.c +24
-21@@ -837,6 +837,25 @@ static bool vlv_power_well_enabled(struct drm_i915_private *dev_priv,static void vlv_display_power_well_init (struct drm_i915_private *dev_priv) { +enum pipe pipe; + +/* +* Enable the CRI clock source so we can get at the +* display and the reference clock for VGA +* hotplug / manual detection. Supposedly DSI also +* needs the ref clock up and running. +* +* CHV DPLL B/C have some issues if VGA mode is enabled. +*/ +for_each_pipe (dev_priv->dev, pipe) { +u32 val =I915_READ (DPLL (pipe)); + + val |=DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; +if (pipe !=PIPE_A ) + val |=DPLL_INTEGRATED_CRI_CLK_VLV ; + +I915_WRITE (DPLL (pipe), val); + }spin_lock_irq (&dev_priv->irq_lock);valleyview_enable_display_irqs (dev_priv);@@ -888,13 +907,7 @@ static void vlv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv, {WARN_ON_ONCE (power_well->data !=PUNIT_POWER_WELL_DPIO_CMN_BC ); -/* -* Enable the CRI clock source so we can get at the -* display and the reference clock for VGA -* hotplug / manual detection. -*/ -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS | -DPLL_REF_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); +/* since ref/cri clock was enabled */ udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */ vlv_set_power_well (dev_priv, power_well, true);@@ -937,22 +950,12 @@ static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv,WARN_ON_ONCE (power_well->data !=PUNIT_POWER_WELL_DPIO_CMN_BC && power_well->data !=PUNIT_POWER_WELL_DPIO_CMN_D ); -/* -* Enable the CRI clock source so we can get at the -* display and the reference clock for VGA -* hotplug / manual detection. -*/ -if (power_well->data ==PUNIT_POWER_WELL_DPIO_CMN_BC ) { +if (power_well->data ==PUNIT_POWER_WELL_DPIO_CMN_BC ) phy =DPIO_PHY0 ; -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS | -DPLL_REF_CLK_ENABLE_VLV ); -I915_WRITE (DPLL (PIPE_B ),I915_READ (DPLL (PIPE_B )) |DPLL_VGA_MODE_DIS | -DPLL_REF_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); - }else { +else phy =DPIO_PHY1 ; -I915_WRITE (DPLL (PIPE_C ),I915_READ (DPLL (PIPE_C )) |DPLL_VGA_MODE_DIS | -DPLL_REF_CLK_ENABLE_VLV |DPLL_INTEGRATED_CRI_CLK_VLV ); - } + +/* since ref/cri clock was enabled */ udelay (1 );/* >10ns for cmnreset, >0ns for sidereset */ vlv_set_power_well (dev_priv, power_well, true);Signature · 8 lines
regards, Sivakumar _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 7 lines
Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 7/9 drm/i915: Make {vlv, chv}_{disable, update}_pll() more similar
In reply to [email protected]From: Ville Syrjälä <[email protected]>
The VLV and CHV DPLL disable and update are almost identical in how the DPLL/DPLL_MD registers need to be set up. But the code looks more different than it really is. Try to bring them into line.
--- drivers/gpu/drm/i915/intel_display.c | 63 ++++++++++++++---------------------- 1 file changed, 25 insertions(+), 38 deletions(-)
drivers/gpu/drm/i915/intel_display.c +25 -38
@@ -1785,16 +1785,13 @@ static void vlv_disable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)/* Make sure the pipe isn't still relying on us */ assert_pipe_disabled (dev_priv, pipe); -/* -* Leave integrated clock source and reference clock enabled for pipe B. -* The latter is needed for VGA hotplug / manual detection. -*/ - val =DPLL_VGA_MODE_DIS ; -if (pipe ==PIPE_B ) - val =DPLL_INTEGRATED_CRI_CLK_VLV |DPLL_REF_CLK_ENABLE_VLV ; + val =DPLL_INTEGRATED_REF_CLK_VLV | +DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ; +if (pipe !=PIPE_A ) + val |=DPLL_INTEGRATED_CRI_CLK_VLV ; +I915_WRITE (DPLL (pipe), val);POSTING_READ (DPLL (pipe)); - }static void chv_disable_pll (struct drm_i915_private *dev_priv,enum pipe pipe)
@@ -1805,11 +1802,11 @@ static void chv_disable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)/* Make sure the pipe isn't still relying on us */ assert_pipe_disabled (dev_priv, pipe); -/* Set PLL en = 0 */ val =DPLL_SSC_REF_CLK_CHV |DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS ;if (pipe !=PIPE_A ) val |=DPLL_INTEGRATED_CRI_CLK_VLV ; +I915_WRITE (DPLL (pipe), val);POSTING_READ (DPLL (pipe));
@@ -7191,24 +7188,27 @@ void intel_dp_set_m_n(struct intel_crtc *crtc, enum link_m_n_set m_n)static void vlv_update_pll (struct intel_crtc *crtc,struct intel_crtc_state *pipe_config) { -u32 dpll, dpll_md; + pipe_config->dpll_hw_state.dpll =DPLL_INTEGRATED_REF_CLK_VLV | +DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS | +DPLL_VCO_ENABLE |DPLL_EXT_BUFFER_ENABLE_VLV ; +if (crtc->pipe !=PIPE_A ) + pipe_config->dpll_hw_state.dpll |=DPLL_INTEGRATED_CRI_CLK_VLV ; -/* -* Enable DPIO clock input. We should never disable the reference -* clock for pipe B, since VGA hotplug / manual detection depends -* on it. -*/ - dpll =DPLL_EXT_BUFFER_ENABLE_VLV |DPLL_REF_CLK_ENABLE_VLV | -DPLL_VGA_MODE_DIS |DPLL_INTEGRATED_REF_CLK_VLV ; -/* We should never disable this, set it here for state tracking */ -if (crtc->pipe ==PIPE_B ) - dpll |=DPLL_INTEGRATED_CRI_CLK_VLV ; - dpll |=DPLL_VCO_ENABLE ; - pipe_config->dpll_hw_state.dpll = dpll; + pipe_config->dpll_hw_state.dpll_md = + (pipe_config->pixel_multiplier -1 ) <<DPLL_MD_UDI_MULTIPLIER_SHIFT ; +} + +static void chv_update_pll (struct intel_crtc *crtc, +struct intel_crtc_state *pipe_config) +{ + pipe_config->dpll_hw_state.dpll =DPLL_SSC_REF_CLK_CHV | +DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS | +DPLL_VCO_ENABLE ; +if (crtc->pipe !=PIPE_A ) + pipe_config->dpll_hw_state.dpll |=DPLL_INTEGRATED_CRI_CLK_VLV ; - dpll_md = (pipe_config->pixel_multiplier -1 ) - <<DPLL_MD_UDI_MULTIPLIER_SHIFT ; - pipe_config->dpll_hw_state.dpll_md = dpll_md; + pipe_config->dpll_hw_state.dpll_md = + (pipe_config->pixel_multiplier -1 ) <<DPLL_MD_UDI_MULTIPLIER_SHIFT ; } static void vlv_prepare_pll(struct intel_crtc *crtc,
@@ -7302,19 +7302,6 @@ static void vlv_prepare_pll(struct intel_crtc *crtc,mutex_unlock (&dev_priv->sb_lock); } -static void chv_update_pll (struct intel_crtc *crtc, -struct intel_crtc_state *pipe_config) -{ - pipe_config->dpll_hw_state.dpll =DPLL_SSC_REF_CLK_CHV | -DPLL_REF_CLK_ENABLE_VLV |DPLL_VGA_MODE_DIS | -DPLL_VCO_ENABLE ; -if (crtc->pipe !=PIPE_A ) - pipe_config->dpll_hw_state.dpll |=DPLL_INTEGRATED_CRI_CLK_VLV ; - - pipe_config->dpll_hw_state.dpll_md = - (pipe_config->pixel_multiplier -1 ) <<DPLL_MD_UDI_MULTIPLIER_SHIFT ; -} -static void chv_prepare_pll (struct intel_crtc *crtc,const struct intel_crtc_state *pipe_config) {
Signature · 6 lines
2.3.6 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 8/9 drm/i915: Implement WaPixelRepeatModeFixForC0:chv
In reply to [email protected]From: Ville Syrjälä <[email protected]>
DPLL_MD(PIPE_C) is AWOL on CHV. Instead of fixing it someone added chicken bits to propagate the pixel multiplier from DPLL_MD(PIPE_B) to either pipe B or C. So do that to make pixel repeat work on pipes B and C. Pipe A is fine without any tricks.
Fortunately the pixel repeat propagation appears to be a oneshot operation, so once the value has been written we can clear the chicken bits. So it is still possible to drive pipe B and C with different pixel multipliers simultaneosly.
Looks like DPLL_VGA_MODE_DIS must also be set in DPLL(PIPE_B) for this to work. But since we keep that bit always set in all DPLLs there's no problem.
This of course means we can't reliably read out the pixel multiplier for pipes B and C. That would make the state checker unhappy, so I added shadow copies of those registers in to dev_priv. The other option would have been to skip pixel multiplier, dpll_md an dotclock checks entirely on CHV, but that feels like a serious loss of cross checking, so just pretending that we have working DPLL MD registers seemed better. Obviously with the shadow copies we can't detect if the pixel multiplier was properly configured, nor can we take over its state from the BIOS, but hopefully people won't have displays that would be limitd to such crappy modes.
There is one strange flicker still remaining. It's visible on pipe C/HDMID when HDMIB is enabled while driven by pipe B. It doesn't occur if pipe A drives HDMIB, nor is there any glitch on pipe B/HDMIB when port C/HDMID starts up. I don't have a board with HDMIC so not sure if it happens there too. So I'm not sure if it's somehow tied in with this strange linkage between pipe B and C. Sadly I was unable to find an enable sequence that would avoid the glitch, but at least it's not fatal ie. the output recovers afterwards.
--- drivers/gpu/drm/i915/i915_drv.h | 7 +++++++ drivers/gpu/drm/i915/i915_reg.h | 3 +++ drivers/gpu/drm/i915/intel_display.c | 30 ++++++++++++++++++++++++++---- 3 files changed, 36 insertions(+), 4 deletions(-)
drivers/gpu/drm/i915/i915_drv.h +7 -0
@@ -1851,7 +1851,14 @@ struct drm_i915_private {u32 fdi_rx_config; +/* Shadow for DISPLAY_PHY_CONTROL which can't be safely read */ u32 chv_phy_control; +/* +* Shadows for CHV DPLL_MD regs to keep the state +* checker somewhat working in the presence hardware +* crappiness (can't read out DPLL_MD for pipes B & C). +*/ +u32 chv_dpll_md[I915_MAX_PIPES ];u32 suspend_count;struct i915_suspend_saved_registers regfile;
drivers/gpu/drm/i915/i915_reg.h +3 -0
@@ -4580,6 +4580,9 @@ enum skl_disp_power_wells {#define CBR1_VLV (VLV_DISPLAY_BASE + 0x70400)#define CBR_PND_DEADLINE_DISABLE (1<<31) +#define CBR4_VLV (VLV_DISPLAY_BASE + 0x70450) +#define CBR_DPLLBMD_PIPE_C (1<<29) +#define CBR_DPLLBMD_PIPE_B (1<<18)/* FIFO watermark sizes etc */ #define G4X_FIFO_LINE_SIZE 64
drivers/gpu/drm/i915/intel_display.c +26 -4
@@ -1667,9 +1667,27 @@ static void chv_enable_pll(struct intel_crtc *crtc,if (wait_for (((I915_READ (DPLL (pipe)) &DPLL_LOCK_VLV ) ==DPLL_LOCK_VLV ),1 ))DRM_ERROR ("PLL %d failed to lock\n" , pipe); -/* not sure when this should be written */ -I915_WRITE (DPLL_MD (pipe), pipe_config->dpll_hw_state.dpll_md); -POSTING_READ (DPLL_MD (pipe)); +if (pipe !=PIPE_A ) { +/* +* WaPixelRepeatModeFixForC0:chv +* +* DPLLCMD is AWOL. Use chicken bits to propagate +* the value from DPLLBMD to either pipe B or C. +*/ +I915_WRITE (CBR4_VLV , pipe ==PIPE_B ?CBR_DPLLBMD_PIPE_B :CBR_DPLLBMD_PIPE_C ); +I915_WRITE (DPLL_MD (PIPE_B ), pipe_config->dpll_hw_state.dpll_md); +I915_WRITE (CBR4_VLV ,0 ); + dev_priv->chv_dpll_md[pipe] = pipe_config->dpll_hw_state.dpll_md; + +/* +* DPLLB VGA mode also seems to cause problems. +* We should always have it disabled. +*/ +WARN_ON ((I915_READ (DPLL (PIPE_B )) &DPLL_VGA_MODE_DIS ) ==0 ); + }else { +I915_WRITE (DPLL_MD (pipe), pipe_config->dpll_hw_state.dpll_md); +POSTING_READ (DPLL_MD (pipe)); + } }static int intel_num_dvo_pipes (struct drm_device *dev)
@@ -8065,7 +8083,11 @@ static bool i9xx_get_pipe_config(struct intel_crtc *crtc,i9xx_get_pfit_config (crtc, pipe_config);if (INTEL_INFO (dev)->gen >=4 ) { - tmp =I915_READ (DPLL_MD (crtc->pipe)); +/* No way to read it out on pipes B and C */ +if (IS_CHERRYVIEW (dev) && crtc->pipe !=PIPE_A ) + tmp = dev_priv->chv_dpll_md[crtc->pipe]; +else + tmp =I915_READ (DPLL_MD (crtc->pipe)); pipe_config->pixel_multiplier = ((tmp &DPLL_MD_UDI_MULTIPLIER_MASK ) >>DPLL_MD_UDI_MULTIPLIER_SHIFT ) +1 ;
Signature · 6 lines
2.3.6 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 8/9] drm/i915: Implement WaPixelRepeatModeFixForC0:chv
Quoted 115 lines · On 6/29/2015 5:55 PM, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
DPLL_MD(PIPE_C)is AWOL on CHV. Instead of fixing it someone added chicken bits to propagate the pixel multiplier fromDPLL_MD(PIPE_B)to either pipe B or C. So do that to make pixel repeat work on pipes B and C. Pipe A is fine without any tricks.Fortunately the pixel repeat propagation appears to be a oneshot operation, so once the value has been written we can clear the chicken bits. So it is still possible to drive pipe B and C with different pixel multipliers simultaneosly.
Looks like
DPLL_VGA_MODE_DISmust also be set inDPLL(PIPE_B)for this to work. But since we keep that bit always set in all DPLLs there's no problem.This of course means we can't reliably read out the pixel multiplier for pipes B and C. That would make the state checker unhappy, so I added shadow copies of those registers in to
dev_priv. The other option would have been to skip pixel multiplier,dpll_mdan dotclock checks entirely on CHV, but that feels like a serious loss of cross checking, so just pretending that we have working DPLL MD registers seemed better. Obviously with the shadow copies we can't detect if the pixel multiplier was properly configured, nor can we take over its state from the BIOS, but hopefully people won't have displays that would be limitd to such crappy modes.There is one strange flicker still remaining. It's visible on pipe C/HDMID when HDMIB is enabled while driven by pipe B. It doesn't occur if pipe A drives HDMIB, nor is there any glitch on pipe B/HDMIB when port C/HDMID starts up. I don't have a board with HDMIC so not sure if it happens there too. So I'm not sure if it's somehow tied in with this strange linkage between pipe B and C. Sadly I was unable to find an enable sequence that would avoid the glitch, but at least it's not fatal ie. the output recovers afterwards.
Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 7 +++++++ drivers/gpu/drm/i915/i915_reg.h | 3 +++ drivers/gpu/drm/i915/intel_display.c | 30 ++++++++++++++++++++++++++---- 3 files changed, 36 insertions(+), 4 deletions(-)drivers/gpu/drm/i915/i915_drv.h +7
-0@@ -1851,7 +1851,14 @@ struct drm_i915_private {u32 fdi_rx_config; +/* Shadow for DISPLAY_PHY_CONTROL which can't be safely read */ u32 chv_phy_control; +/* +* Shadows for CHV DPLL_MD regs to keep the state +* checker somewhat working in the presence hardware +* crappiness (can't read out DPLL_MD for pipes B & C). +*/ +u32 chv_dpll_md[I915_MAX_PIPES ];u32 suspend_count;struct i915_suspend_saved_registers regfile;drivers/gpu/drm/i915/i915_reg.h +3
-0@@ -4580,6 +4580,9 @@ enum skl_disp_power_wells {#define CBR1_VLV (VLV_DISPLAY_BASE + 0x70400)#define CBR_PND_DEADLINE_DISABLE (1<<31) +#define CBR4_VLV (VLV_DISPLAY_BASE + 0x70450) +#define CBR_DPLLBMD_PIPE_C (1<<29) +#define CBR_DPLLBMD_PIPE_B (1<<18)/* FIFO watermark sizes etc */ #define G4X_FIFO_LINE_SIZE 64drivers/gpu/drm/i915/intel_display.c +21
-3@@ -1667,9 +1667,27 @@ static void chv_enable_pll(struct intel_crtc *crtc,if (wait_for (((I915_READ (DPLL (pipe)) &DPLL_LOCK_VLV ) ==DPLL_LOCK_VLV ),1 ))DRM_ERROR ("PLL %d failed to lock\n" , pipe); -/* not sure when this should be written */ -I915_WRITE (DPLL_MD (pipe), pipe_config->dpll_hw_state.dpll_md); -POSTING_READ (DPLL_MD (pipe)); +if (pipe !=PIPE_A ) { +/* +* WaPixelRepeatModeFixForC0:chv +* +* DPLLCMD is AWOL. Use chicken bits to propagate +* the value from DPLLBMD to either pipe B or C. +*/ +I915_WRITE (CBR4_VLV , pipe ==PIPE_B ?CBR_DPLLBMD_PIPE_B :CBR_DPLLBMD_PIPE_C ); +I915_WRITE (DPLL_MD (PIPE_B ), pipe_config->dpll_hw_state.dpll_md); +I915_WRITE (CBR4_VLV ,0 ); + dev_priv->chv_dpll_md[pipe] = pipe_config->dpll_hw_state.dpll_md; + +/* +* DPLLB VGA mode also seems to cause problems. +* We should always have it disabled. +*/ +WARN_ON ((I915_READ (DPLL (PIPE_B )) &DPLL_VGA_MODE_DIS ) ==0 ); + }else { +I915_WRITE (DPLL_MD (pipe), pipe_config->dpll_hw_state.dpll_md); +POSTING_READ (DPLL_MD (pipe)); + } }static int intel_num_dvo_pipes (struct drm_device *dev)@@ -8065,7 +8083,11 @@ static bool i9xx_get_pipe_config(struct intel_crtc *crtc,i9xx_get_pfit_config (crtc, pipe_config);
drivers/gpu/drm/i915/intel_display.c static bool i9xx_get_pipe_config(struct intel_crtc *crtc, · line 8093
Quoted 10 lines
drivers/gpu/drm/i915/intel_display.c +5
-1if (INTEL_INFO (dev)->gen >=4 ) { - tmp =I915_READ (DPLL_MD (crtc->pipe)); +/* No way to read it out on pipes B and C */ +if (IS_CHERRYVIEW (dev) && crtc->pipe !=PIPE_A ) + tmp = dev_priv->chv_dpll_md[crtc->pipe]; +else + tmp =I915_READ (DPLL_MD (crtc->pipe)); pipe_config->pixel_multiplier = ((tmp &DPLL_MD_UDI_MULTIPLIER_MASK ) >>DPLL_MD_UDI_MULTIPLIER_SHIFT ) +1 ;
correct me if my understanding is wrong, the only place we used to read pixel_multiplier was in i9xx_get_pipe_config and we have replaced even that with dev_priv variables ? so the first time we get pipe_config will it return 0 ?
i assume the right thing here is to read the CBR4_VLV and check if the current pipe is enabled, if so return the value in DPLL_MD(PIPE_B) as required.
On a side note, we should calculate pixel_multiplier as part of compute_dpll instead of depending on GOP/VBIOS programmed values.
Signature · 7 lines
regards, Sivakumar _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 8/9] drm/i915: Implement WaPixelRepeatModeFixForC0:chv
Quoted 118 lines · Sivakumar Thulasimani
Quoted 115 lines · On 6/29/2015 5:55 PM, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
DPLL_MD(PIPE_C)is AWOL on CHV. Instead of fixing it someone added chicken bits to propagate the pixel multiplier fromDPLL_MD(PIPE_B)to either pipe B or C. So do that to make pixel repeat work on pipes B and C. Pipe A is fine without any tricks.Fortunately the pixel repeat propagation appears to be a oneshot operation, so once the value has been written we can clear the chicken bits. So it is still possible to drive pipe B and C with different pixel multipliers simultaneosly.
Looks like
DPLL_VGA_MODE_DISmust also be set inDPLL(PIPE_B)for this to work. But since we keep that bit always set in all DPLLs there's no problem.This of course means we can't reliably read out the pixel multiplier for pipes B and C. That would make the state checker unhappy, so I added shadow copies of those registers in to
dev_priv. The other option would have been to skip pixel multiplier,dpll_mdan dotclock checks entirely on CHV, but that feels like a serious loss of cross checking, so just pretending that we have working DPLL MD registers seemed better. Obviously with the shadow copies we can't detect if the pixel multiplier was properly configured, nor can we take over its state from the BIOS, but hopefully people won't have displays that would be limitd to such crappy modes.There is one strange flicker still remaining. It's visible on pipe C/HDMID when HDMIB is enabled while driven by pipe B. It doesn't occur if pipe A drives HDMIB, nor is there any glitch on pipe B/HDMIB when port C/HDMID starts up. I don't have a board with HDMIC so not sure if it happens there too. So I'm not sure if it's somehow tied in with this strange linkage between pipe B and C. Sadly I was unable to find an enable sequence that would avoid the glitch, but at least it's not fatal ie. the output recovers afterwards.
Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 7 +++++++ drivers/gpu/drm/i915/i915_reg.h | 3 +++ drivers/gpu/drm/i915/intel_display.c | 30 ++++++++++++++++++++++++++---- 3 files changed, 36 insertions(+), 4 deletions(-)drivers/gpu/drm/i915/i915_drv.h +7
-0@@ -1851,7 +1851,14 @@ struct drm_i915_private {u32 fdi_rx_config; +/* Shadow for DISPLAY_PHY_CONTROL which can't be safely read */ u32 chv_phy_control; +/* +* Shadows for CHV DPLL_MD regs to keep the state +* checker somewhat working in the presence hardware +* crappiness (can't read out DPLL_MD for pipes B & C). +*/ +u32 chv_dpll_md[I915_MAX_PIPES ];u32 suspend_count;struct i915_suspend_saved_registers regfile;drivers/gpu/drm/i915/i915_reg.h +3
-0@@ -4580,6 +4580,9 @@ enum skl_disp_power_wells {#define CBR1_VLV (VLV_DISPLAY_BASE + 0x70400)#define CBR_PND_DEADLINE_DISABLE (1<<31) +#define CBR4_VLV (VLV_DISPLAY_BASE + 0x70450) +#define CBR_DPLLBMD_PIPE_C (1<<29) +#define CBR_DPLLBMD_PIPE_B (1<<18)/* FIFO watermark sizes etc */ #define G4X_FIFO_LINE_SIZE 64drivers/gpu/drm/i915/intel_display.c +21
-3@@ -1667,9 +1667,27 @@ static void chv_enable_pll(struct intel_crtc *crtc,if (wait_for (((I915_READ (DPLL (pipe)) &DPLL_LOCK_VLV ) ==DPLL_LOCK_VLV ),1 ))DRM_ERROR ("PLL %d failed to lock\n" , pipe); -/* not sure when this should be written */ -I915_WRITE (DPLL_MD (pipe), pipe_config->dpll_hw_state.dpll_md); -POSTING_READ (DPLL_MD (pipe)); +if (pipe !=PIPE_A ) { +/* +* WaPixelRepeatModeFixForC0:chv +* +* DPLLCMD is AWOL. Use chicken bits to propagate +* the value from DPLLBMD to either pipe B or C. +*/ +I915_WRITE (CBR4_VLV , pipe ==PIPE_B ?CBR_DPLLBMD_PIPE_B :CBR_DPLLBMD_PIPE_C ); +I915_WRITE (DPLL_MD (PIPE_B ), pipe_config->dpll_hw_state.dpll_md); +I915_WRITE (CBR4_VLV ,0 ); + dev_priv->chv_dpll_md[pipe] = pipe_config->dpll_hw_state.dpll_md; + +/* +* DPLLB VGA mode also seems to cause problems. +* We should always have it disabled. +*/ +WARN_ON ((I915_READ (DPLL (PIPE_B )) &DPLL_VGA_MODE_DIS ) ==0 ); + }else { +I915_WRITE (DPLL_MD (pipe), pipe_config->dpll_hw_state.dpll_md); +POSTING_READ (DPLL_MD (pipe)); + } }static int intel_num_dvo_pipes (struct drm_device *dev)@@ -8065,7 +8083,11 @@ static bool i9xx_get_pipe_config(struct intel_crtc *crtc,i9xx_get_pfit_config (crtc, pipe_config);
Quoted 15 lines
drivers/gpu/drm/i915/intel_display.c static bool i9xx_get_pipe_config(struct intel_crtc *crtc, · line 8093
Quoted 10 lines
drivers/gpu/drm/i915/intel_display.c +5
-1if (INTEL_INFO (dev)->gen >=4 ) { - tmp =I915_READ (DPLL_MD (crtc->pipe)); +/* No way to read it out on pipes B and C */ +if (IS_CHERRYVIEW (dev) && crtc->pipe !=PIPE_A ) + tmp = dev_priv->chv_dpll_md[crtc->pipe]; +else + tmp =I915_READ (DPLL_MD (crtc->pipe)); pipe_config->pixel_multiplier = ((tmp &DPLL_MD_UDI_MULTIPLIER_MASK ) >>DPLL_MD_UDI_MULTIPLIER_SHIFT ) +1 ;correct me if my understanding is wrong, the only place we used to read
pixel_multiplierwas ini9xx_get_pipe_configand we have replaced even that withdev_privvariables ? so the first time
we getpipe_configwill it return 0 ?
Yes. Which means 1x multiplier.
Quoted 3 lines
i assume the right thing here is to read the
CBR4_VLVand check if the current pipe is enabled,
if so return the value inDPLL_MD(PIPE_B)as required.
That won't work since the pixel multiplier update is a one-shot operation. We migth be able to read the value back from one pipe by looking at CBR4_VLV if the chicken bit for the pipe was left enabled after the value was set, but there's no way to read back the value for the second pipe. If both chicken bits are cleared in CBR4_VLV (which is how I implemeted it) we can't read back the value for either pipe.
Quoted 3 lines
On a side note, we should calculate
pixel_multiplieras part ofcompute_dpllinstead of depending
on GOP/VBIOS programmed values.
It's computed as part of encoder->compute_config().
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 9/9 drm/i915: Disable DSI PLL before reconfiguring it
In reply to [email protected]From: Ville Syrjälä <[email protected]>
The BIOS maybe leave the DSI PLL enabled even if the port is disabled. The PLL doesn't seem to like being reconfigured while it's enabled so make sure it's disabled before doing that.
The better fix would be to expose all PLLs independently of their ports so that we could disable any unused ones during the sanitize phase. But this seems like an OK short term solution.
--- drivers/gpu/drm/i915/intel_dsi.c | 1 + 1 file changed, 1 insertion(+)
drivers/gpu/drm/i915/intel_dsi.c +1 -0
@@ -907,6 +907,7 @@ static void intel_dsi_pre_pll_enable(struct intel_encoder *encoder)intel_dsi_prepare (encoder); +vlv_disable_dsi_pll (encoder);vlv_enable_dsi_pll (encoder); }
Signature · 6 lines
2.3.6 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 9/9] drm/i915: Disable DSI PLL before reconfiguring it
Quoted 27 lines · On 6/29/2015 5:55 PM, [email protected] wrote:
From: Ville Syrjälä <[email protected]>
The BIOS maybe leave the DSI PLL enabled even if the port is disabled. The PLL doesn't seem to like being reconfigured while it's enabled so make sure it's disabled before doing that.
The better fix would be to expose all PLLs independently of their ports so that we could disable any unused ones during the sanitize phase. But this seems like an OK short term solution.
Signed-off-by Ville Syrjälä <[email protected]>--- drivers/gpu/drm/i915/intel_dsi.c | 1 + 1 file changed, 1 insertion(+)drivers/gpu/drm/i915/intel_dsi.c +1
-0@@ -907,6 +907,7 @@ static void intel_dsi_pre_pll_enable(struct intel_encoder *encoder)intel_dsi_prepare (encoder); +vlv_disable_dsi_pll (encoder);vlv_enable_dsi_pll (encoder); }
Signature · 2 lines
regards, Sivakumar
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx