Skip to contentSkip to conversation

usb: Move xhci_pme_quirk() behind an #ifdef CONFIG_PM, as it is not used when it's not defined

PATCH In review Tomer Barletz 2 participants 3 messages Aug 18, 2015 – Aug 27, 2015

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 usb: Move xhci_pme_quirk() behind an #ifdef CONFIG_PM, as it is not used when it's not defined

---
 drivers/usb/host/xhci-pci.c | 90 ++++++++++++++++++++++-----------------------
 1 file changed, 45 insertions(+), 45 deletions(-)
drivers/usb/host/xhci-pci.c +45 -45
index 5590eac..c79d336 100644
@@ -180,51 +180,6 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
 				"QUIRK: Resetting on resume");
 }
 
-/*
- * In some Intel xHCI controllers, in order to get D3 working,
- * through a vendor specific SSIC CONFIG register at offset 0x883c,
- * SSIC PORT need to be marked as "unused" before putting xHCI
- * into D3. After D3 exit, the SSIC port need to be marked as "used".
- * Without this change, xHCI might not enter D3 state.
- * Make sure PME works on some Intel xHCI controllers by writing 1 to clear
- * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4
- */
-static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend)
-{
-	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
-	struct pci_dev		*pdev = to_pci_dev(hcd->self.controller);
-	u32 val;
-	void __iomem *reg;
-
-	if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
-		 pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) {
-
-		reg = (void __iomem *) xhci->cap_regs + PORT2_SSIC_CONFIG_REG2;
-
-		/* Notify SSIC that SSIC profile programming is not done */
-		val = readl(reg) & ~PROG_DONE;
-		writel(val, reg);
-
-		/* Mark SSIC port as unused(suspend) or used(resume) */
-		val = readl(reg);
-		if (suspend)
-			val |= SSIC_PORT_UNUSED;
-		else
-			val &= ~SSIC_PORT_UNUSED;
-		writel(val, reg);
-
-		/* Notify SSIC that SSIC profile programming is done */
-		val = readl(reg) | PROG_DONE;
-		writel(val, reg);
-		readl(reg);
-	}
-
-	reg = (void __iomem *) xhci->cap_regs + 0x80a4;
-	val = readl(reg);
-	writel(val | BIT(28), reg);
-	readl(reg);
-}
-
 #ifdef CONFIG_ACPI
 static void xhci_pme_acpi_rtd3_enable(struct pci_dev *dev)
 {
@@ -345,6 +300,51 @@ static void xhci_pci_remove(struct pci_dev *dev)
 }
 
 #ifdef CONFIG_PM
+/*
+ * In some Intel xHCI controllers, in order to get D3 working,
+ * through a vendor specific SSIC CONFIG register at offset 0x883c,
+ * SSIC PORT need to be marked as "unused" before putting xHCI
+ * into D3. After D3 exit, the SSIC port need to be marked as "used".
+ * Without this change, xHCI might not enter D3 state.
+ * Make sure PME works on some Intel xHCI controllers by writing 1 to clear
+ * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4
+ */
+static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend)
+{
+	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
+	struct pci_dev		*pdev = to_pci_dev(hcd->self.controller);
+	u32 val;
+	void __iomem *reg;
+
+	if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
+		 pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) {
+
+		reg = (void __iomem *) xhci->cap_regs + PORT2_SSIC_CONFIG_REG2;
+
+		/* Notify SSIC that SSIC profile programming is not done */
+		val = readl(reg) & ~PROG_DONE;
+		writel(val, reg);
+
+		/* Mark SSIC port as unused(suspend) or used(resume) */
+		val = readl(reg);
+		if (suspend)
+			val |= SSIC_PORT_UNUSED;
+		else
+			val &= ~SSIC_PORT_UNUSED;
+		writel(val, reg);
+
+		/* Notify SSIC that SSIC profile programming is done */
+		val = readl(reg) | PROG_DONE;
+		writel(val, reg);
+		readl(reg);
+	}
+
+	reg = (void __iomem *) xhci->cap_regs + 0x80a4;
+	val = readl(reg);
+	writel(val | BIT(28), reg);
+	readl(reg);
+}
+
 static int xhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup)
 {
 	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
Signature · 1 line
2.4.3
#1 lore raw

Ping.

Quoted 116 lines · Tomer Barletz
---
 drivers/usb/host/xhci-pci.c | 90 ++++++++++++++++++++++-----------------------
 1 file changed, 45 insertions(+), 45 deletions(-)
drivers/usb/host/xhci-pci.c +45 -46
index 5590eac..c79d336 100644
@@ -180,51 +180,6 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
                                "QUIRK: Resetting on resume");
 }
 
-/*
- * In some Intel xHCI controllers, in order to get D3 working,
- * through a vendor specific SSIC CONFIG register at offset 0x883c,
- * SSIC PORT need to be marked as "unused" before putting xHCI
- * into D3. After D3 exit, the SSIC port need to be marked as "used".
- * Without this change, xHCI might not enter D3 state.
- * Make sure PME works on some Intel xHCI controllers by writing 1 to clear
- * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4
- */
-static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend)
-{
-       struct xhci_hcd *xhci = hcd_to_xhci(hcd);
-       struct pci_dev          *pdev = to_pci_dev(hcd->self.controller);
-       u32 val;
-       void __iomem *reg;
-
-       if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
-                pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) {
-
-               reg = (void __iomem *) xhci->cap_regs + PORT2_SSIC_CONFIG_REG2;
-
-               /* Notify SSIC that SSIC profile programming is not done */
-               val = readl(reg) & ~PROG_DONE;
-               writel(val, reg);
-
-               /* Mark SSIC port as unused(suspend) or used(resume) */
-               val = readl(reg);
-               if (suspend)
-                       val |= SSIC_PORT_UNUSED;
-               else
-                       val &= ~SSIC_PORT_UNUSED;
-               writel(val, reg);
-
-               /* Notify SSIC that SSIC profile programming is done */
-               val = readl(reg) | PROG_DONE;
-               writel(val, reg);
-               readl(reg);
-       }
-
-       reg = (void __iomem *) xhci->cap_regs + 0x80a4;
-       val = readl(reg);
-       writel(val | BIT(28), reg);
-       readl(reg);
-}
-
 #ifdef CONFIG_ACPI
 static void xhci_pme_acpi_rtd3_enable(struct pci_dev *dev)
 {
@@ -345,6 +300,51 @@ static void xhci_pci_remove(struct pci_dev *dev)
 }
 
 #ifdef CONFIG_PM
+/*
+ * In some Intel xHCI controllers, in order to get D3 working,
+ * through a vendor specific SSIC CONFIG register at offset 0x883c,
+ * SSIC PORT need to be marked as "unused" before putting xHCI
+ * into D3. After D3 exit, the SSIC port need to be marked as "used".
+ * Without this change, xHCI might not enter D3 state.
+ * Make sure PME works on some Intel xHCI controllers by writing 1 to clear
+ * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4
+ */
+static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend)
+{
+       struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+       struct pci_dev          *pdev = to_pci_dev(hcd->self.controller);
+       u32 val;
+       void __iomem *reg;
+
+       if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
+                pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) {
+
+               reg = (void __iomem *) xhci->cap_regs + PORT2_SSIC_CONFIG_REG2;
+
+               /* Notify SSIC that SSIC profile programming is not done */
+               val = readl(reg) & ~PROG_DONE;
+               writel(val, reg);
+
+               /* Mark SSIC port as unused(suspend) or used(resume) */
+               val = readl(reg);
+               if (suspend)
+                       val |= SSIC_PORT_UNUSED;
+               else
+                       val &= ~SSIC_PORT_UNUSED;
+               writel(val, reg);
+
+               /* Notify SSIC that SSIC profile programming is done */
+               val = readl(reg) | PROG_DONE;
+               writel(val, reg);
+               readl(reg);
+       }
+
+       reg = (void __iomem *) xhci->cap_regs + 0x80a4;
+       val = readl(reg);
+       writel(val | BIT(28), reg);
+       readl(reg);
+}
+
 static int xhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup)
 {
        struct xhci_hcd *xhci = hcd_to_xhci(hcd);
--

2.4.3

#2 lore raw
Quoted 2 lines · Tomer Barletz

Ping.

Ah, yes, makes sense.
I'll add it

-Mathias