dts: zc770-xm010: Enable zynq qspi controller node
Subsystems (3)
PATCH v5 7/16 dts: zc770-xm010: Enable zynq qspi controller node
Enabled zynq qspi controller node for zc770-xm010 board.
=> sf probe 0 -- bus1 for selecting qspi controller => sf probe 1 -- bus0 for selecting spi controller
---
Changes for v2. v3, v4:
- none
Changes for v5:
- Make qspi as spi0
arch/arm/dts/zynq-zc770-xm010.dts | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)
arch/arm/dts/zynq-zc770-xm010.dts +6 -1
@@ -16,7 +16,8 @@ ethernet0 = &gem0; i2c0 = &i2c0; serial0 = &uart1; - spi0 = &spi1; + spi0 = &qspi; + spi1 = &spi1; }; chosen {
@@ -53,6 +54,10 @@ }; }; +&qspi { + status = "okay"; +}; + &can0 { status = "okay"; };
Signature · 1 line
1.9.1
PATCH v5 13/16 spi: Kconfig: Add Zynq QSPI controller entry
Add Zynq QSPI controller Kconfig entry.
---
Changes for v2. v3, v4:
- none
Changes for v5:
- Remove TARGET_XILINX_ZYNQMP
drivers/spi/Kconfig | 9 +++++++++ 1 file changed, 9 insertions(+)
drivers/spi/Kconfig +9 -0
@@ -131,6 +131,15 @@ config ZYNQ_SPI access the SPI NOR flash on platforms embedding this Zynq SPI IP core. +config ZYNQ_QSPI + bool "Zynq QSPI driver" + depends on ARCH_ZYNQ + help + Enable the Zynq Quad-SPI (QSPI) driver. This driver can be + used to access the SPI NOR flash on platforms embedding this + Zynq QSPI IP core. This IP is used to connect the flash in + 4-bit qspi, 8-bit dual stacked and shared 4-bit dual parallel. + endif # if DM_SPI config FSL_ESPI
Signature · 1 line
1.9.1
PATCH v5 13/16 spi: Kconfig: Add Zynq QSPI controller entry
Quoted 6 lines · Jagan Teki
Add Zynq QSPI controller
Kconfigentry.Signed-off-by Jagan Teki <[email protected]>Reviewed-by Simon Glass <[email protected]>Cc Michal Simek <[email protected]>Cc Siva Durga Prasad Paladugu <[email protected]>
Quoted 9 lines
---
Changes for v2. v3, v4:
- none
Changes for v5:
- RemoveTARGET_XILINX_ZYNQMPdrivers/spi/Kconfig | 9 +++++++++ 1 file changed, 9 insertions(+)
Thanks,
Michal
PATCH v5 13/16 spi: Kconfig: Add Zynq QSPI controller entry
Quoted 13 lines · Michal Simek
Quoted 12 lines · Jagan Teki
Add Zynq QSPI controller
Kconfigentry.Signed-off-by Jagan Teki <[email protected]>Reviewed-by Simon Glass <[email protected]>Cc Michal Simek <[email protected]>Cc Siva Durga Prasad Paladugu <[email protected]>---
Changes for v2. v3, v4:
- none
Changes for v5:
- RemoveTARGET_XILINX_ZYNQMP
Quoted 5 lines
Quoted 3 lines
drivers/spi/Kconfig | 9 +++++++++ 1 file changed, 9 insertions(+)Acked-by Michal Simek <[email protected]>
Applied to u-boot-spi/master
thanks!
Signature · 1 line
Jagan | openedev.
PATCH v5 7/16 dts: zc770-xm010: Enable zynq qspi controller node
In reply to Jagan TekiQuoted 9 lines · Jagan Teki
Enabled zynq qspi controller node for zc770-xm010 board.
=> sf probe 0 -- bus1 for selecting qspi controller => sf probe 1 -- bus0 for selecting spi controller
Signed-off-by Jagan Teki <[email protected]>Cc Simon Glass <[email protected]>Cc Siva Durga Prasad Paladugu <[email protected]>Cc Michal Simek <[email protected]>
Quoted 8 lines
---
Changes for v2. v3, v4:
- none
Changes for v5:
- Make qspi as spi0arch/arm/dts/zynq-zc770-xm010.dts | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)
Thanks,
Michal
PATCH v5 7/16 dts: zc770-xm010: Enable zynq qspi controller node
Quoted 16 lines · Michal Simek
Quoted 15 lines · Jagan Teki
Enabled zynq qspi controller node for zc770-xm010 board.
=> sf probe 0 -- bus1 for selecting qspi controller => sf probe 1 -- bus0 for selecting spi controller
Signed-off-by Jagan Teki <[email protected]>Cc Simon Glass <[email protected]>Cc Siva Durga Prasad Paladugu <[email protected]>Cc Michal Simek <[email protected]>---
Changes for v2. v3, v4:
- none
Changes for v5:
- Make qspi as spi0
Quoted 4 lines
Quoted 2 lines
arch/arm/dts/zynq-zc770-xm010.dts | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)Acked-by Michal Simek <[email protected]>
Applied to u-boot-spi/master
thanks!
Signature · 1 line
Jagan | openedev.