Skip to contentSkip to conversation

Mediatek xHCI support

PATCH Superseded Chunfeng Yun 5 participants 19 messages Sep 8, 2015 – Oct 6, 2015

Subsystems (6)

v7 of 12 Superseded Latest is v12 →

lore
Share & tools
lore

Chunfeng Yun

author maintainer
#0 lore raw

v7 cover Mediatek xHCI support

The patch supports MediaTek's xHCI controller.

There are some differences from xHCI spec:
1. The interval is specified in 250 * 8ns increments for Interrupt Moderation Interval(IMODI) of the Interrupter Moderation(IMOD) register, it is 8 times as much as that defined in xHCI spec.

2. For the value of TD Size in Normal TRB, MTK's xHCI controller defines a number of packets that remain to be transferred for a TD after processing all Max packets in all previous TRBs,that means don't include the current TRB's, but in xHCI spec it includes the current ones.

3. To minimize the scheduling effort for synchronous endpoints in xHC, the MTK architecture defines some extra SW scheduling parameters for HW. According to these parameters provided by SW, the xHC can easily decide whether a synchronous endpoint should be scheduled in a specific uFrame. The extra SW scheduling parameters are put into reserved DWs in Slot and Endpoint Context. And a bandwidth scheduler algorithm is added to support such feature.

A usb3.0 phy driver is also added which used by mt65xx SoCs platform, it supports two usb2.0 ports and one usb3.0 port.

Change in v7:
1. remove xHCI timing setting which only for FPGA
2. revise xHCI scheduler algorithms
3. replace "usb" by "USB" in xHCI binding file

Change in v6:
1. get register base address of port in probe instead of of_xlate
2. enable clock in phy_init instead of probe

Change in v5:
1. descripte more exactly for each specifiers in xHCI binding
2. make use of new multi-phy feature for phy driver

Change in v4:
1. descripte more exactly for each specifiers in binding file
2. use BIT() to define a bit mask mcro

Change in v3:
1. implement generic phy
2. move opperations for IPPC and wakeup from phy driver to xHCI driver
3. seperate quirk functions into a single C file to fix up dependence issue

Change in v2:
1. Rebase to 4.2-rc1
2. Remove probe phy before add usb_hcd patch from this series due to 4.2-rc1 already fix this issue
3. add xhci mac clocks
4. add suspend/resume
5. support remote wakeup

Chunfeng Yun (5):
dt-bindings: Add usb3.0 phy binding for MT65xx SoCs
dt-bindings: Add a binding for Mediatek xHCI host controller
usb: phy: add usb3.0 phy driver for mt65xx SoCs
xhci: mediatek: support MTK xHCI host controller
arm64: dts: mediatek: add xHCI & usb phy for mt8173

 .../devicetree/bindings/phy/phy-mt65xx-usb.txt     |  69 ++
 .../devicetree/bindings/usb/mt8173-xhci.txt        |  52 ++
 arch/arm64/boot/dts/mediatek/mt8173-evb.dts        |  16 +
 arch/arm64/boot/dts/mediatek/mt8173.dtsi           |  44 ++
 drivers/phy/Kconfig                                |   9 +
 drivers/phy/Makefile                               |   1 +
 drivers/phy/phy-mt65xx-usb3.c                      | 456 ++++++++++++
 drivers/usb/host/Kconfig                           |   9 +
 drivers/usb/host/Makefile                          |   4 +
 drivers/usb/host/xhci-mtk-sch.c                    | 449 ++++++++++++
 drivers/usb/host/xhci-mtk.c                        | 765 +++++++++++++++++++++
 drivers/usb/host/xhci-mtk.h                        | 121 ++++
 drivers/usb/host/xhci-ring.c                       |  35 +-
 drivers/usb/host/xhci.c                            |  19 +-
 drivers/usb/host/xhci.h                            |   1 +
 15 files changed, 2043 insertions(+), 7 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
 create mode 100644 Documentation/devicetree/bindings/usb/mt8173-xhci.txt
 create mode 100644 drivers/phy/phy-mt65xx-usb3.c
 create mode 100644 drivers/usb/host/xhci-mtk-sch.c
 create mode 100644 drivers/usb/host/xhci-mtk.c
 create mode 100644 drivers/usb/host/xhci-mtk.h

--
1.8.1.1.dirty

author maintainer
#1 lore raw

PATCH v7 1/5 dt-bindings: Add usb3.0 phy binding for MT65xx SoCs

add a DT binding documentation of usb3.0 phy for MT65xx SoCs from Mediatek.

---
 .../devicetree/bindings/phy/phy-mt65xx-usb.txt     | 69 ++++++++++++++++++++++
 1 file changed, 69 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt new file +69 -0
new file mode 100644
index 0000000..5812d20
@@ -0,0 +1,69 @@
+mt65xx USB3.0 PHY binding
+--------------------------
+
+This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
+
+Required properties (controller (parent) node):
+ - compatible	: should be "mediatek,mt8173-u3phy"
+ - reg		: offset and length of register for phy, exclude port's
+		  register.
+ - clocks	: a list of phandle + clock-specifier pairs, one for each
+		  entry in clock-names
+ - clock-names	: must contain
+		  "u3phya_ref": for reference clock of usb3.0 analog phy.
+
+Required nodes	: a sub-node is required for each port the controller
+		  provides. Address range information including the usual
+		  'reg' property is used inside these nodes to describe
+		  the controller's topology. These nodes are translated
+		  by the driver's .xlate() function.
+
+Required properties (port (child) node):
+- reg		: address and length of the register set for the port.
+- #phy-cells	: should be 1 (See second example)
+		  cell after port phandle is phy type from:
+			- PHY_TYPE_USB2
+			- PHY_TYPE_USB3
+
+Example:
+
+u3phy: usb-phy at 11290000 {
+	compatible = "mediatek,mt8173-u3phy";
+	reg = <0 0x11290000 0 0x800>;
+	clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+	clock-names = "u3phya_ref";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	ranges;
+	status = "okay";
+
+	phy_port0: port at 11290800 {
+		reg = <0 0x11290800 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+
+	phy_port1: port at 11291000 {
+		reg = <0 0x11291000 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+};
+
+Specifying phy control of devices
+---------------------------------
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type;
+phy-names for each port are optional.
+
+Example:
+
+#include <dt-bindings/phy/phy.h>
+
+usb30: usb at 11270000 {
+	...
+	phys = <&phy_port0 PHY_TYPE_USB3>;
+	phy-names = "usb3-0";
+	...
+};
Signature · 1 line
1.8.1.1.dirty
maintainer Acked-by on v7 1/5
#2 lore raw

Re: [PATCH v7 1/5] dt-bindings: Add usb3.0 phy binding for MT65xx SoCs

Quoted 4 lines · Chunfeng Yun

add a DT binding documentation of usb3.0 phy for MT65xx SoCs from Mediatek.

One comment, otherwise:

Quoted 20 lines
---
 .../devicetree/bindings/phy/phy-mt65xx-usb.txt     | 69 ++++++++++++++++++++++
 1 file changed, 69 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt new file +9 -0
new file mode 100644
index 0000000..5812d20
@@ -0,0 +1,69 @@
+mt65xx USB3.0 PHY binding
+--------------------------
+
+This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
+
+Required properties (controller (parent) node):
+ - compatible	: should be "mediatek,mt8173-u3phy"
+ - reg		: offset and length of register for phy, exclude port's
+		  register.

Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt line 19

Quoted 10 lines
Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt new file +10 -0
+ - clocks	: a list of phandle + clock-specifier pairs, one for each
+		  entry in clock-names
+ - clock-names	: must contain
+		  "u3phya_ref": for reference clock of usb3.0 analog phy.
+
+Required nodes	: a sub-node is required for each port the controller
+		  provides. Address range information including the usual
+		  'reg' property is used inside these nodes to describe
+		  the controller's topology. These nodes are translated
+		  by the driver's .xlate() function.

The last sentence is Linux specific. Please remove.

Quoted 51 lines
Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt new file +50 -0
+
+Required properties (port (child) node):
+- reg		: address and length of the register set for the port.
+- #phy-cells	: should be 1 (See second example)
+		  cell after port phandle is phy type from:
+			- PHY_TYPE_USB2
+			- PHY_TYPE_USB3
+
+Example:
+
+u3phy: usb-phy at 11290000 {
+	compatible = "mediatek,mt8173-u3phy";
+	reg = <0 0x11290000 0 0x800>;
+	clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+	clock-names = "u3phya_ref";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	ranges;
+	status = "okay";
+
+	phy_port0: port at 11290800 {
+		reg = <0 0x11290800 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+
+	phy_port1: port at 11291000 {
+		reg = <0 0x11291000 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+};
+
+Specifying phy control of devices
+---------------------------------
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type;
+phy-names for each port are optional.
+
+Example:
+
+#include <dt-bindings/phy/phy.h>
+
+usb30: usb at 11270000 {
+	...
+	phys = <&phy_port0 PHY_TYPE_USB3>;
+	phy-names = "usb3-0";
+	...
+};
author maintainer
#3 lore raw

Re: [PATCH v7 1/5] dt-bindings: Add usb3.0 phy binding for MT65xx SoCs

Hi,

Quoted 34 lines · Rob Herring
Quoted 4 lines · Chunfeng Yun

add a DT binding documentation of usb3.0 phy for MT65xx SoCs from Mediatek.

One comment, otherwise:

Quoted 24 lines
---
 .../devicetree/bindings/phy/phy-mt65xx-usb.txt     | 69 ++++++++++++++++++++++
 1 file changed, 69 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt new file +13 -0
new file mode 100644
index 0000000..5812d20
@@ -0,0 +1,69 @@
+mt65xx USB3.0 PHY binding
+--------------------------
+
+This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
+
+Required properties (controller (parent) node):
+ - compatible	: should be "mediatek,mt8173-u3phy"
+ - reg		: offset and length of register for phy, exclude port's
+		  register.
+ - clocks	: a list of phandle + clock-specifier pairs, one for each
+		  entry in clock-names
+ - clock-names	: must contain
+		  "u3phya_ref": for reference clock of usb3.0 analog phy.
Quoted 9 lines

Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt line 19

Quoted 6 lines
Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt new file +6 -0
+
+Required nodes	: a sub-node is required for each port the controller
+		  provides. Address range information including the usual
+		  'reg' property is used inside these nodes to describe
+		  the controller's topology. These nodes are translated
+		  by the driver's .xlate() function.

The last sentence is Linux specific. Please remove.

Ok, I will remove it later. Thanks

Quoted 52 lines
Quoted 51 lines
Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt new file +50 -0
+
+Required properties (port (child) node):
+- reg		: address and length of the register set for the port.
+- #phy-cells	: should be 1 (See second example)
+		  cell after port phandle is phy type from:
+			- PHY_TYPE_USB2
+			- PHY_TYPE_USB3
+
+Example:
+
+u3phy: usb-phy at 11290000 {
+	compatible = "mediatek,mt8173-u3phy";
+	reg = <0 0x11290000 0 0x800>;
+	clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+	clock-names = "u3phya_ref";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	ranges;
+	status = "okay";
+
+	phy_port0: port at 11290800 {
+		reg = <0 0x11290800 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+
+	phy_port1: port at 11291000 {
+		reg = <0 0x11291000 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+};
+
+Specifying phy control of devices
+---------------------------------
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type;
+phy-names for each port are optional.
+
+Example:
+
+#include <dt-bindings/phy/phy.h>
+
+usb30: usb at 11270000 {
+	...
+	phys = <&phy_port0 PHY_TYPE_USB3>;
+	phy-names = "usb3-0";
+	...
+};
maintainer Acked-by on v7 1/5
#4 lore raw

Re: [PATCH v7 1/5] dt-bindings: Add usb3.0 phy binding for MT65xx SoCs

In reply to Chunfeng Yun
Quoted 4 lines · Chunfeng Yun

add a DT binding documentation of usb3.0 phy for MT65xx SoCs from Mediatek.

Quoted 81 lines
---
 .../devicetree/bindings/phy/phy-mt65xx-usb.txt     | 69 ++++++++++++++++++++++
 1 file changed, 69 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt new file +69 -0
new file mode 100644
index 0000000..5812d20
@@ -0,0 +1,69 @@
+mt65xx USB3.0 PHY binding
+--------------------------
+
+This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
+
+Required properties (controller (parent) node):
+ - compatible	: should be "mediatek,mt8173-u3phy"
+ - reg		: offset and length of register for phy, exclude port's
+		  register.
+ - clocks	: a list of phandle + clock-specifier pairs, one for each
+		  entry in clock-names
+ - clock-names	: must contain
+		  "u3phya_ref": for reference clock of usb3.0 analog phy.
+
+Required nodes	: a sub-node is required for each port the controller
+		  provides. Address range information including the usual
+		  'reg' property is used inside these nodes to describe
+		  the controller's topology. These nodes are translated
+		  by the driver's .xlate() function.
+
+Required properties (port (child) node):
+- reg		: address and length of the register set for the port.
+- #phy-cells	: should be 1 (See second example)
+		  cell after port phandle is phy type from:
+			- PHY_TYPE_USB2
+			- PHY_TYPE_USB3
+
+Example:
+
+u3phy: usb-phy at 11290000 {
+	compatible = "mediatek,mt8173-u3phy";
+	reg = <0 0x11290000 0 0x800>;
+	clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+	clock-names = "u3phya_ref";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	ranges;
+	status = "okay";
+
+	phy_port0: port at 11290800 {
+		reg = <0 0x11290800 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+
+	phy_port1: port at 11291000 {
+		reg = <0 0x11291000 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+};
+
+Specifying phy control of devices
+---------------------------------
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type;
+phy-names for each port are optional.
+
+Example:
+
+#include <dt-bindings/phy/phy.h>
+
+usb30: usb at 11270000 {
+	...
+	phys = <&phy_port0 PHY_TYPE_USB3>;
+	phy-names = "usb3-0";
+	...
+};
author maintainer
#5 lore raw

PATCH v7 2/5 dt-bindings: Add a binding for Mediatek xHCI host controller

In reply to Chunfeng Yun

add a DT binding documentation of xHCI host controller for the MT8173 SoC from Mediatek.

---
 .../devicetree/bindings/usb/mt8173-xhci.txt        | 52 ++++++++++++++++++++++
 1 file changed, 52 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/usb/mt8173-xhci.txt
Documentation/devicetree/bindings/usb/mt8173-xhci.txt new file +52 -0
new file mode 100644
index 0000000..d851bf1
@@ -0,0 +1,52 @@
+MT8173 xHCI
+
+The device node for Mediatek SOC USB3.0 host controller
+
+Required properties:
+ - compatible : should contain "mediatek,mt8173-xhci"
+ - reg : specifies physical base address and size of the registers,
+	the first one for MAC, the second for IPPC
+ - interrupts : interrupt used by the controller
+ - power-domains : a phandle to USB power domain node to control USB's
+	mtcmos
+ - vusb33-supply : regulator of USB avdd3.3v
+
+ - clocks : a list of phandle + clock-specifier pairs, one for each
+	entry in clock-names
+ - clock-names : must contain
+	"sys_ck": for clock of xHCI MAC
+	"wakeup_deb_p0": for USB wakeup debounce clock of port0
+	"wakeup_deb_p0": for USB wakeup debounce clock of port1
+
+ - phys : a list of phandle + phy specifier pairs
+ - usb3-lpm-capable : supports USB3.0 LPM
+ - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup
+	control register
+ - mediatek,wakeup-src : 1: ip sleep wakeup mode; 2: line state wakeup
+	mode; Others means don't enable wakeup source of USB
+
+Optional properties:
+ - vbus-supply : reference to the VBUS regulator;
+
+Example:
+usb30: usb at 11270000 {
+	compatible = "mediatek,mt8173-xhci";
+	reg = <0 0x11270000 0 0x1000>,
+	      <0 0x11280700 0 0x0100>;
+	interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+	power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+	clocks = <&topckgen CLK_TOP_USB30_SEL>,
+		 <&pericfg CLK_PERI_USB0>,
+		 <&pericfg CLK_PERI_USB1>;
+	clock-names = "sys_ck",
+		      "wakeup_deb_p0",
+		      "wakeup_deb_p1";
+	phys = <&phy_port0 PHY_TYPE_USB3>,
+	       <&phy_port1 PHY_TYPE_USB2>;
+	vusb33-supply = <&mt6397_vusb_reg>;
+	vbus-supply = <&usb_p1_vbus>;
+	usb3-lpm-capable;
+	mediatek,syscon-wakeup = <&pericfg>;
+	mediatek,wakeup-src = <1>;
+	status = "okay";
+};
Signature · 1 line
1.8.1.1.dirty
maintainer
#6 lore raw

Re: [PATCH v7 2/5] dt-bindings: Add a binding for Mediatek xHCI host controller

Quoted 29 lines · Chunfeng Yun

add a DT binding documentation of xHCI host controller for the MT8173 SoC from Mediatek.

---
 .../devicetree/bindings/usb/mt8173-xhci.txt        | 52 ++++++++++++++++++++++
 1 file changed, 52 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/usb/mt8173-xhci.txt
Documentation/devicetree/bindings/usb/mt8173-xhci.txt new file +14 -0
new file mode 100644
index 0000000..d851bf1
@@ -0,0 +1,52 @@
+MT8173 xHCI
+
+The device node for Mediatek SOC USB3.0 host controller
+
+Required properties:
+ - compatible : should contain "mediatek,mt8173-xhci"
+ - reg : specifies physical base address and size of the registers,
+	the first one for MAC, the second for IPPC
+ - interrupts : interrupt used by the controller
+ - power-domains : a phandle to USB power domain node to control USB's
+	mtcmos
+ - vusb33-supply : regulator of USB avdd3.3v
+
+ - clocks : a list of phandle + clock-specifier pairs, one for each

Documentation/devicetree/bindings/usb/mt8173-xhci.txt line 24

Quoted 10 lines
Documentation/devicetree/bindings/usb/mt8173-xhci.txt new file +10 -0
+	entry in clock-names
+ - clock-names : must contain
+	"sys_ck": for clock of xHCI MAC
+	"wakeup_deb_p0": for USB wakeup debounce clock of port0
+	"wakeup_deb_p0": for USB wakeup debounce clock of port1
+
+ - phys : a list of phandle + phy specifier pairs
+ - usb3-lpm-capable : supports USB3.0 LPM
+ - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup
+	control register

Wake-up should probably be done in some generic way. That said, I don't have a specific suggestion other than make it optional.

Documentation/devicetree/bindings/usb/mt8173-xhci.txt line 26

Quoted 2 lines
Documentation/devicetree/bindings/usb/mt8173-xhci.txt new file +2 -0
+ - mediatek,wakeup-src : 1: ip sleep wakeup mode; 2: line state wakeup
+	mode; Others means don't enable wakeup source of USB

This should be optional rather than any other value meaning disabled.

Quoted 27 lines
Documentation/devicetree/bindings/usb/mt8173-xhci.txt new file +26 -0
+
+Optional properties:
+ - vbus-supply : reference to the VBUS regulator;
+
+Example:
+usb30: usb at 11270000 {
+	compatible = "mediatek,mt8173-xhci";
+	reg = <0 0x11270000 0 0x1000>,
+	      <0 0x11280700 0 0x0100>;
+	interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+	power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+	clocks = <&topckgen CLK_TOP_USB30_SEL>,
+		 <&pericfg CLK_PERI_USB0>,
+		 <&pericfg CLK_PERI_USB1>;
+	clock-names = "sys_ck",
+		      "wakeup_deb_p0",
+		      "wakeup_deb_p1";
+	phys = <&phy_port0 PHY_TYPE_USB3>,
+	       <&phy_port1 PHY_TYPE_USB2>;
+	vusb33-supply = <&mt6397_vusb_reg>;
+	vbus-supply = <&usb_p1_vbus>;
+	usb3-lpm-capable;
+	mediatek,syscon-wakeup = <&pericfg>;
+	mediatek,wakeup-src = <1>;
+	status = "okay";
+};
author maintainer
#7 lore raw

Re: [PATCH v7 2/5] dt-bindings: Add a binding for Mediatek xHCI host controller

Quoted 44 lines · Rob Herring
Quoted 29 lines · Chunfeng Yun

add a DT binding documentation of xHCI host controller for the MT8173 SoC from Mediatek.

---
 .../devicetree/bindings/usb/mt8173-xhci.txt        | 52 ++++++++++++++++++++++
 1 file changed, 52 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/usb/mt8173-xhci.txt
Documentation/devicetree/bindings/usb/mt8173-xhci.txt new file +14 -0
new file mode 100644
index 0000000..d851bf1
@@ -0,0 +1,52 @@
+MT8173 xHCI
+
+The device node for Mediatek SOC USB3.0 host controller
+
+Required properties:
+ - compatible : should contain "mediatek,mt8173-xhci"
+ - reg : specifies physical base address and size of the registers,
+	the first one for MAC, the second for IPPC
+ - interrupts : interrupt used by the controller
+ - power-domains : a phandle to USB power domain node to control USB's
+	mtcmos
+ - vusb33-supply : regulator of USB avdd3.3v
+
+ - clocks : a list of phandle + clock-specifier pairs, one for each

Documentation/devicetree/bindings/usb/mt8173-xhci.txt line 24

Quoted 10 lines
Documentation/devicetree/bindings/usb/mt8173-xhci.txt new file +10 -0
+	entry in clock-names
+ - clock-names : must contain
+	"sys_ck": for clock of xHCI MAC
+	"wakeup_deb_p0": for USB wakeup debounce clock of port0
+	"wakeup_deb_p0": for USB wakeup debounce clock of port1
+
+ - phys : a list of phandle + phy specifier pairs
+ - usb3-lpm-capable : supports USB3.0 LPM
+ - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup
+	control register

Wake-up should probably be done in some generic way. That said, I don't have a specific suggestion other than make it optional.

Quoted 5 lines

Documentation/devicetree/bindings/usb/mt8173-xhci.txt line 26

Quoted 2 lines
Documentation/devicetree/bindings/usb/mt8173-xhci.txt new file +2 -0
+ - mediatek,wakeup-src : 1: ip sleep wakeup mode; 2: line state wakeup
+	mode; Others means don't enable wakeup source of USB

This should be optional rather than any other value meaning disabled.

Ok, "mediatek,wakeup-src" and "mediatek,syscon-wakeup" properties will be put into optional.

Thanks a lot

Quoted 28 lines
Quoted 27 lines
Documentation/devicetree/bindings/usb/mt8173-xhci.txt new file +26 -0
+
+Optional properties:
+ - vbus-supply : reference to the VBUS regulator;
+
+Example:
+usb30: usb at 11270000 {
+	compatible = "mediatek,mt8173-xhci";
+	reg = <0 0x11270000 0 0x1000>,
+	      <0 0x11280700 0 0x0100>;
+	interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+	power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+	clocks = <&topckgen CLK_TOP_USB30_SEL>,
+		 <&pericfg CLK_PERI_USB0>,
+		 <&pericfg CLK_PERI_USB1>;
+	clock-names = "sys_ck",
+		      "wakeup_deb_p0",
+		      "wakeup_deb_p1";
+	phys = <&phy_port0 PHY_TYPE_USB3>,
+	       <&phy_port1 PHY_TYPE_USB2>;
+	vusb33-supply = <&mt6397_vusb_reg>;
+	vbus-supply = <&usb_p1_vbus>;
+	usb3-lpm-capable;
+	mediatek,syscon-wakeup = <&pericfg>;
+	mediatek,wakeup-src = <1>;
+	status = "okay";
+};
author maintainer
#8 lore raw

PATCH v7 3/5 usb: phy: add usb3.0 phy driver for mt65xx SoCs

In reply to Chunfeng Yun

support usb3.0 phy of mt65xx SoCs

---
 drivers/phy/Kconfig           |   9 +
 drivers/phy/Makefile          |   1 +
 drivers/phy/phy-mt65xx-usb3.c | 456 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 466 insertions(+)
 create mode 100644 drivers/phy/phy-mt65xx-usb3.c
drivers/phy/Kconfig +9 -0
index c0e6ede..019cf8b 100644
@@ -193,6 +193,15 @@ config PHY_HIX5HD2_SATA
 	help
 	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
 
+config PHY_MT65XX_USB3
+	tristate "Mediatek USB3.0 PHY Driver"
+	depends on ARCH_MEDIATEK && OF
+	select GENERIC_PHY
+	help
+	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
+	  for mt65xx SoCs. it supports two usb2.0 ports and
+	  one usb3.0 port.
+
 config PHY_SUN4I_USB
 	tristate "Allwinner sunxi SoC USB PHY driver"
 	depends on ARCH_SUNXI && HAS_IOMEM && OF
drivers/phy/Makefile +1 -0
index f344e1b..3ceff2a 100644
@@ -22,6 +22,7 @@ obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
 obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
 obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
 obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
+obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
 obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
 obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
 obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
drivers/phy/phy-mt65xx-usb3.c new file +456 -0

456 lines not on this page · raw message

Signature · 1 line
1.8.1.1.dirty
author maintainer
#9 lore raw

PATCH v7 4/5 xhci: mediatek: support MTK xHCI host controller

In reply to Chunfeng Yun

There some vendor quirks for MTK xhci host controller:
1. It defines some extra SW scheduling parameters for HW to minimize the scheduling effort for synchronous and interrupt endpoints. The parameters are put into reseved DWs of slot context and endpoint context.
2. Its IMODI unit for Interrupter Moderation register is 8 times as much as that defined in xHCI spec.
3. Its TDS in Normal TRB defines a number of packets that remains to be transferred for a TD after processing all Max packets in all previous TRBs.

---
 drivers/usb/host/Kconfig        |   9 +
 drivers/usb/host/Makefile       |   4 +
 drivers/usb/host/xhci-mtk-sch.c | 449 +++++++++++++++++++++++
 drivers/usb/host/xhci-mtk.c     | 765 ++++++++++++++++++++++++++++++++++++++++
 drivers/usb/host/xhci-mtk.h     | 121 +++++++
 drivers/usb/host/xhci-ring.c    |  35 +-
 drivers/usb/host/xhci.c         |  19 +-
 drivers/usb/host/xhci.h         |   1 +
 8 files changed, 1396 insertions(+), 7 deletions(-)
 create mode 100644 drivers/usb/host/xhci-mtk-sch.c
 create mode 100644 drivers/usb/host/xhci-mtk.c
 create mode 100644 drivers/usb/host/xhci-mtk.h
drivers/usb/host/Kconfig +9 -0
index 8afc3c1..358ab6d 100644
@@ -34,6 +34,15 @@ config USB_XHCI_PCI
 config USB_XHCI_PLATFORM
 	tristate
 
+config USB_XHCI_MTK
+	tristate "xHCI support for Mediatek MT65xx"
+	select MFD_SYSCON
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	---help---
+	  Say 'Y' to enable the support for the xHCI host controller
+	  found in Mediatek MT65xx SoCs.
+	  If unsure, say N.
+
 config USB_XHCI_MVEBU
 	tristate "xHCI support for Marvell Armada 375/38x"
 	select USB_XHCI_PLATFORM
drivers/usb/host/Makefile +4 -0
index 754efaa..00401f9 100644
@@ -13,6 +13,9 @@ fhci-$(CONFIG_FHCI_DEBUG) += fhci-dbg.o
 xhci-hcd-y := xhci.o xhci-mem.o
 xhci-hcd-y += xhci-ring.o xhci-hub.o xhci-dbg.o
 xhci-hcd-y += xhci-trace.o
+ifneq ($(CONFIG_USB_XHCI_MTK), )
+	xhci-hcd-y += xhci-mtk-sch.o
+endif
 
 xhci-plat-hcd-y := xhci-plat.o
 ifneq ($(CONFIG_USB_XHCI_MVEBU), )
@@ -30,6 +33,7 @@ endif
 
 obj-$(CONFIG_USB_XHCI_PCI)	+= xhci-pci.o
 obj-$(CONFIG_USB_XHCI_PLATFORM) += xhci-plat-hcd.o
+obj-$(CONFIG_USB_XHCI_MTK)	+= xhci-mtk.o
 
 obj-$(CONFIG_USB_EHCI_HCD)	+= ehci-hcd.o
 obj-$(CONFIG_USB_EHCI_PCI)	+= ehci-pci.o
drivers/usb/host/xhci-mtk-sch.c new file +449 -0

449 lines not on this page · raw message

drivers/usb/host/xhci-mtk.c new file +765 -0

765 lines not on this page · raw message

drivers/usb/host/xhci-mtk.h new file +121 -0

121 lines not on this page · raw message

drivers/usb/host/xhci-ring.c +29 -6
index 94416ff..73997a0 100644
@@ -68,6 +68,7 @@
 #include <linux/slab.h>
 #include "xhci.h"
 #include "xhci-trace.h"
+#include "xhci-mtk.h"
 
 /*
  * Returns zero if the TRB isn't in this segment, otherwise it returns the DMA
@@ -3131,9 +3132,14 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 
 		/* Set the TRB length, TD size, and interrupter fields. */
 		if (xhci->hci_version < 0x100) {
-			remainder = xhci_td_remainder(
+			if (xhci->quirks & XHCI_MTK_HOST) {
+				remainder = xhci_mtk_td_remainder_quirk(
+					running_total, trb_buff_len, urb);
+			} else {
+				remainder = xhci_td_remainder(
 					urb->transfer_buffer_length -
 					running_total);
+			}
 		} else {
 			remainder = xhci_v1_0_td_remainder(running_total,
 					trb_buff_len, total_packet_count, urb,
@@ -3286,9 +3292,14 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 
 		/* Set the TRB length, TD size, and interrupter fields. */
 		if (xhci->hci_version < 0x100) {
-			remainder = xhci_td_remainder(
+			if (xhci->quirks & XHCI_MTK_HOST) {
+				remainder = xhci_mtk_td_remainder_quirk(
+					running_total, trb_buff_len, urb);
+			} else {
+				remainder = xhci_td_remainder(
 					urb->transfer_buffer_length -
 					running_total);
+			}
 		} else {
 			remainder = xhci_v1_0_td_remainder(running_total,
 					trb_buff_len, total_packet_count, urb,
@@ -3383,7 +3394,7 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 		field |= 0x1;
 
 	/* xHCI 1.0 6.4.1.2.1: Transfer Type field */
-	if (xhci->hci_version == 0x100) {
+	if ((xhci->hci_version == 0x100) || (xhci->quirks & XHCI_MTK_HOST)) {
 		if (urb->transfer_buffer_length > 0) {
 			if (setup->bRequestType & USB_DIR_IN)
 				field |= TRB_TX_TYPE(TRB_DATA_IN);
@@ -3407,8 +3418,14 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 		field = TRB_TYPE(TRB_DATA);
 
 	length_field = TRB_LEN(urb->transfer_buffer_length) |
-		xhci_td_remainder(urb->transfer_buffer_length) |
 		TRB_INTR_TARGET(0);
+
+	if (xhci->quirks & XHCI_MTK_HOST)
+		length_field |= xhci_mtk_td_remainder_quirk(0,
+				urb->transfer_buffer_length, urb);
+	else
+		length_field |= xhci_td_remainder(urb->transfer_buffer_length);
+
 	if (urb->transfer_buffer_length > 0) {
 		if (setup->bRequestType & USB_DIR_IN)
 			field |= TRB_DIR_IN;
@@ -3632,8 +3649,14 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 
 			/* Set the TRB length, TD size, & interrupter fields. */
 			if (xhci->hci_version < 0x100) {
-				remainder = xhci_td_remainder(
-						td_len - running_total);
+				if (xhci->quirks & XHCI_MTK_HOST) {
+					remainder = xhci_mtk_td_remainder_quirk(
+						running_total, trb_buff_len,
+						urb);
+				} else {
+					remainder = xhci_td_remainder(
+							td_len - running_total);
+				}
 			} else {
 				remainder = xhci_v1_0_td_remainder(
 						running_total, trb_buff_len,
drivers/usb/host/xhci.c +18 -1
index 7da0d60..209fc8a 100644
@@ -31,6 +31,7 @@
 
 #include "xhci.h"
 #include "xhci-trace.h"
+#include "xhci-mtk.h"
 
 #define DRIVER_AUTHOR "Sarah Sharp"
 #define DRIVER_DESC "'eXtensible' Host Controller (xHC) Driver"
@@ -623,7 +624,11 @@ int xhci_run(struct usb_hcd *hcd)
 			"// Set the interrupt modulation register");
 	temp = readl(&xhci->ir_set->irq_control);
 	temp &= ~ER_IRQ_INTERVAL_MASK;
-	temp |= (u32) 160;
+	/*
+	 * the increment interval is 8 times as much as that defined
+	 * in xHCI spec on MTK's controller
+	 */
+	temp |= (u32) ((xhci->quirks & XHCI_MTK_HOST) ? 20 : 160);
 	writel(temp, &xhci->ir_set->irq_control);
 
 	/* Set the HCD state before we enable the irqs */
@@ -1688,6 +1693,9 @@ int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 
 	xhci_endpoint_zero(xhci, xhci->devs[udev->slot_id], ep);
 
+	if (xhci->quirks & XHCI_MTK_HOST)
+		xhci_mtk_drop_ep_quirk(hcd, udev, ep);
+
 	xhci_dbg(xhci, "drop ep 0x%x, slot id %d, new drop flags = %#x, new add flags = %#x\n",
 			(unsigned int) ep->desc.bEndpointAddress,
 			udev->slot_id,
@@ -1783,6 +1791,15 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 		return -ENOMEM;
 	}
 
+	if (xhci->quirks & XHCI_MTK_HOST) {
+		ret = xhci_mtk_add_ep_quirk(hcd, udev, ep);
+		if (ret < 0) {
+			xhci_free_or_cache_endpoint_ring(xhci,
+				virt_dev, ep_index);
+			return ret;
+		}
+	}
+
 	ctrl_ctx->add_flags |= cpu_to_le32(added_ctxs);
 	new_add_flags = le32_to_cpu(ctrl_ctx->add_flags);
 
drivers/usb/host/xhci.h +1 -0
index 31e46cc..d257ce3 100644
@@ -1567,6 +1567,7 @@ struct xhci_hcd {
 /* For controllers with a broken beyond repair streams implementation */
 #define XHCI_BROKEN_STREAMS	(1 << 19)
 #define XHCI_PME_STUCK_QUIRK	(1 << 20)
+#define XHCI_MTK_HOST		(1 << 21)
 	unsigned int		num_active_eps;
 	unsigned int		limit_active_eps;
 	/* There are two roothubs to keep track of bus suspend info for */
Signature · 1 line
1.8.1.1.dirty
maintainer
#10 lore raw

Re: [PATCH v7 4/5] xhci: mediatek: support MTK xHCI host controller

Hi

Quoted 11 lines · Chunfeng Yun

There some vendor quirks for MTK xhci host controller:
1. It defines some extra SW scheduling parameters for HW to minimize the scheduling effort for synchronous and interrupt endpoints. The parameters are put into reseved DWs of slot context and endpoint context.
2. Its IMODI unit for Interrupter Moderation register is 8 times as much as that defined in xHCI spec.
3. Its TDS in Normal TRB defines a number of packets that remains to be transferred for a TD after processing all Max packets in all previous TRBs.

I just rewrote and unified the the xhci TD remainder functions, now we got only one xhci_td_remainder() function which should be more suitable for quirks.

You can add the quirk directly to it, no need to duplicate the whole function.

-Mathias

#11 lore raw

PATCH 1/1 xhci: create one unified function to calculate TRB TD remainder.

xhci versions 1.0 and later report the untransferred data remaining in a TD a bit differently than older hosts.

We used to have separate functions for these, and needed to check host
version before calling the right function.

Now Mediatek host has an additional quirk on how it uses the TD Size field for remaining data. To prevent yet another function for calculating remainder we instead want to make one quirk friendly unified function.

---
 drivers/usb/host/xhci-ring.c | 106 ++++++++++++++++++-------------------------
 drivers/usb/host/xhci.h      |   2 +
 2 files changed, 46 insertions(+), 62 deletions(-)
drivers/usb/host/xhci-ring.c +44 -62
index a47a1e8..57f40a1 100644
@@ -3020,21 +3020,6 @@ int xhci_queue_intr_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 }
 
 /*
- * The TD size is the number of bytes remaining in the TD (including this TRB),
- * right shifted by 10.
- * It must fit in bits 21:17, so it can't be bigger than 31.
- */
-static u32 xhci_td_remainder(unsigned int remainder)
-{
-	u32 max = (1 << (21 - 17 + 1)) - 1;
-
-	if ((remainder >> 10) >= max)
-		return max << 17;
-	else
-		return (remainder >> 10) << 17;
-}
-
-/*
  * For xHCI 1.0 host controllers, TD size is the number of max packet sized
  * packets remaining in the TD (*not* including this TRB).
  *
@@ -3046,30 +3031,36 @@ static u32 xhci_td_remainder(unsigned int remainder)
  *
  * TD size = total_packet_count - packets_transferred
  *
- * It must fit in bits 21:17, so it can't be bigger than 31.
+ * For xHCI 0.96 and older, TD size field should be the remaining bytes
+ * including this TRB, right shifted by 10
+ *
+ * For all hosts it must fit in bits 21:17, so it can't be bigger than 31.
+ * This is taken care of in the TRB_TD_SIZE() macro
+ *
  * The last TRB in a TD must have the TD size set to zero.
  */
-static u32 xhci_v1_0_td_remainder(int running_total, int trb_buff_len,
-		unsigned int total_packet_count, struct urb *urb,
-		unsigned int num_trbs_left)
+static u32 xhci_td_remainder(struct xhci_hcd *xhci, int transferred,
+			      int trb_buff_len, unsigned int td_total_len,
+			      struct urb *urb, unsigned int num_trbs_left)
 {
-	int packets_transferred;
+	u32 maxp, total_packet_count;
+
+	if (xhci->hci_version < 0x100)
+		return ((td_total_len - transferred) >> 10);
+
+	maxp = GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
+	total_packet_count = DIV_ROUND_UP(td_total_len, maxp);
 
 	/* One TRB with a zero-length data packet. */
-	if (num_trbs_left == 0 || (running_total == 0 && trb_buff_len == 0))
+	if (num_trbs_left == 0 || (transferred == 0 && trb_buff_len == 0) ||
+	    trb_buff_len == td_total_len)
 		return 0;
 
-	/* All the TRB queueing functions don't count the current TRB in
-	 * running_total.
-	 */
-	packets_transferred = (running_total + trb_buff_len) /
-		GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
-
-	if ((total_packet_count - packets_transferred) > 31)
-		return 31 << 17;
-	return (total_packet_count - packets_transferred) << 17;
+	/* Queueing functions don't count the current TRB into transferred */
+	return (total_packet_count - ((transferred + trb_buff_len) / maxp));
 }
 
+
 static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 		struct urb *urb, int slot_id, unsigned int ep_index)
 {
@@ -3191,17 +3182,12 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 		}
 
 		/* Set the TRB length, TD size, and interrupter fields. */
-		if (xhci->hci_version < 0x100) {
-			remainder = xhci_td_remainder(
-					urb->transfer_buffer_length -
-					running_total);
-		} else {
-			remainder = xhci_v1_0_td_remainder(running_total,
-					trb_buff_len, total_packet_count, urb,
-					num_trbs - 1);
-		}
+		remainder = xhci_td_remainder(xhci, running_total, trb_buff_len,
+					   urb->transfer_buffer_length,
+					   urb, num_trbs - 1);
+
 		length_field = TRB_LEN(trb_buff_len) |
-			remainder |
+			TRB_TD_SIZE(remainder) |
 			TRB_INTR_TARGET(0);
 
 		if (num_trbs > 1)
@@ -3364,17 +3350,12 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 			field |= TRB_ISP;
 
 		/* Set the TRB length, TD size, and interrupter fields. */
-		if (xhci->hci_version < 0x100) {
-			remainder = xhci_td_remainder(
-					urb->transfer_buffer_length -
-					running_total);
-		} else {
-			remainder = xhci_v1_0_td_remainder(running_total,
-					trb_buff_len, total_packet_count, urb,
-					num_trbs - 1);
-		}
+		remainder = xhci_td_remainder(xhci, running_total, trb_buff_len,
+					   urb->transfer_buffer_length,
+					   urb, num_trbs - 1);
+
 		length_field = TRB_LEN(trb_buff_len) |
-			remainder |
+			TRB_TD_SIZE(remainder) |
 			TRB_INTR_TARGET(0);
 
 		if (num_trbs > 1)
@@ -3412,7 +3393,7 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 	struct usb_ctrlrequest *setup;
 	struct xhci_generic_trb *start_trb;
 	int start_cycle;
-	u32 field, length_field;
+	u32 field, length_field, remainder;
 	struct urb_priv *urb_priv;
 	struct xhci_td *td;
 
@@ -3485,9 +3466,15 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 	else
 		field = TRB_TYPE(TRB_DATA);
 
+	remainder = xhci_td_remainder(xhci, 0,
+				   urb->transfer_buffer_length,
+				   urb->transfer_buffer_length,
+				   urb, 1);
+
 	length_field = TRB_LEN(urb->transfer_buffer_length) |
-		xhci_td_remainder(urb->transfer_buffer_length) |
+		TRB_TD_SIZE(remainder) |
 		TRB_INTR_TARGET(0);
+
 	if (urb->transfer_buffer_length > 0) {
 		if (setup->bRequestType & USB_DIR_IN)
 			field |= TRB_DIR_IN;
@@ -3816,17 +3803,12 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 				trb_buff_len = td_remain_len;
 
 			/* Set the TRB length, TD size, & interrupter fields. */
-			if (xhci->hci_version < 0x100) {
-				remainder = xhci_td_remainder(
-						td_len - running_total);
-			} else {
-				remainder = xhci_v1_0_td_remainder(
-						running_total, trb_buff_len,
-						total_packet_count, urb,
-						(trbs_per_td - j - 1));
-			}
+			remainder = xhci_td_remainder(xhci, running_total,
+						   trb_buff_len, td_len,
+						   urb, trbs_per_td - j - 1);
+
 			length_field = TRB_LEN(trb_buff_len) |
-				remainder |
+				TRB_TD_SIZE(remainder) |
 				TRB_INTR_TARGET(0);
 
 			queue_trb(xhci, ep_ring, more_trbs_coming,
drivers/usb/host/xhci.h +2 -0
index dbda41e..ea8b904 100644
@@ -1136,6 +1136,8 @@ enum xhci_setup_dev {
 /* Normal TRB fields */
 /* transfer_len bitmasks - bits 0:16 */
 #define	TRB_LEN(p)		((p) & 0x1ffff)
+/* TD Size, packets remaining in this TD, bits 21:17 (5 bits, so max 31) */
+#define TRB_TD_SIZE(p)          (min((p), (u32)31) << 17)
 /* Interrupter Target - which MSI-X vector to target the completion event at */
 #define TRB_INTR_TARGET(p)	(((p) & 0x3ff) << 22)
 #define GET_INTR_TARGET(p)	(((p) >> 22) & 0x3ff)
Signature · 1 line
1.9.1
#12 lore raw

Re: [PATCH] xhci: create one unified function to calculate TRB TD remainder.

Quoted 4 lines · Mathias Nyman

Now Mediatek host has an additional quirk on how it uses the TD Size field for remaining data. To prevent yet another function for calculating
remainder we instead want to make one quirk friendly unified function.

Could you clarify whether this replaces an existing quirk or renders unnecessary the introduction of a new quirk, because that decides whether this patch must go into stable.

Regards
Oliver

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html

#13 lore raw

Re: [PATCH] xhci: create one unified function to calculate TRB TD remainder.

Quoted 10 lines · Oliver Neukum
Quoted 4 lines · Mathias Nyman

Now Mediatek host has an additional quirk on how it uses the TD Size field for remaining data. To prevent yet another function for calculating
remainder we instead want to make one quirk friendly unified function.

Could you clarify whether this replaces an existing quirk or renders unnecessary the introduction of a new quirk, because that decides whether this patch must go into stable.

Neither :)

This patch will simplify the quirk Mediatek wants to include in their patchseries.

After this patch the TD size part of the mediatek quirk can be reduced to maybe a couple lines in total.
Yet another version of the Mediatek patcheries will be needed after this, but it will be 50 - 100 lines shorter.

This patch is basically just code refactoring, enabling easier quirking.

It seems I need to do some rewording of the commit message of this patch as well

-Mathias

author maintainer
#14 lore raw

Re: [PATCH] xhci: create one unified function to calculate TRB TD remainder.

In reply to Mathias Nyman

Hi,

Quoted 67 lines · Mathias Nyman

xhci versions 1.0 and later report the untransferred data remaining in a TD a bit differently than older hosts.

We used to have separate functions for these, and needed to check host
version before calling the right function.

Now Mediatek host has an additional quirk on how it uses the TD Size field for remaining data. To prevent yet another function for calculating remainder we instead want to make one quirk friendly unified function.

---
 drivers/usb/host/xhci-ring.c | 106 ++++++++++++++++++-------------------------
 drivers/usb/host/xhci.h      |   2 +
 2 files changed, 46 insertions(+), 62 deletions(-)
drivers/usb/host/xhci-ring.c +13 -20
index a47a1e8..57f40a1 100644
@@ -3020,21 +3020,6 @@ int xhci_queue_intr_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 }
 
 /*
- * The TD size is the number of bytes remaining in the TD (including this TRB),
- * right shifted by 10.
- * It must fit in bits 21:17, so it can't be bigger than 31.
- */
-static u32 xhci_td_remainder(unsigned int remainder)
-{
-	u32 max = (1 << (21 - 17 + 1)) - 1;
-
-	if ((remainder >> 10) >= max)
-		return max << 17;
-	else
-		return (remainder >> 10) << 17;
-}
-
-/*
  * For xHCI 1.0 host controllers, TD size is the number of max packet sized
  * packets remaining in the TD (*not* including this TRB).
  *
@@ -3046,30 +3031,36 @@ static u32 xhci_td_remainder(unsigned int remainder)
  *
  * TD size = total_packet_count - packets_transferred
  *
- * It must fit in bits 21:17, so it can't be bigger than 31.
+ * For xHCI 0.96 and older, TD size field should be the remaining bytes
+ * including this TRB, right shifted by 10
+ *
+ * For all hosts it must fit in bits 21:17, so it can't be bigger than 31.
+ * This is taken care of in the TRB_TD_SIZE() macro
+ *
  * The last TRB in a TD must have the TD size set to zero.
  */
-static u32 xhci_v1_0_td_remainder(int running_total, int trb_buff_len,
-		unsigned int total_packet_count, struct urb *urb,
-		unsigned int num_trbs_left)
+static u32 xhci_td_remainder(struct xhci_hcd *xhci, int transferred,
+			      int trb_buff_len, unsigned int td_total_len,
+			      struct urb *urb, unsigned int num_trbs_left)
 {
-	int packets_transferred;
+	u32 maxp, total_packet_count;
+
+	if (xhci->hci_version < 0x100)
+		return ((td_total_len - transferred) >> 10);

drivers/usb/host/xhci-ring.c static u32 xhci_td_remainder(unsigned int remainder) · line 3058

Quoted 10 lines
drivers/usb/host/xhci-ring.c +5 -1
+
+	maxp = GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
+	total_packet_count = DIV_ROUND_UP(td_total_len, maxp);
 
 	/* One TRB with a zero-length data packet. */
-	if (num_trbs_left == 0 || (running_total == 0 && trb_buff_len == 0))
+	if (num_trbs_left == 0 || (transferred == 0 && trb_buff_len == 0) ||
+	    trb_buff_len == td_total_len)
 		return 0;
 

I think when trb_buff_len == td_total_len, the TD only needs one trb, so num_trbs_left will equal to 0; that means no need add this condition.

Quoted 117 lines
drivers/usb/host/xhci-ring.c +26 -41
-	/* All the TRB queueing functions don't count the current TRB in
-	 * running_total.
-	 */
-	packets_transferred = (running_total + trb_buff_len) /
-		GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
-
-	if ((total_packet_count - packets_transferred) > 31)
-		return 31 << 17;
-	return (total_packet_count - packets_transferred) << 17;
+	/* Queueing functions don't count the current TRB into transferred */
+	return (total_packet_count - ((transferred + trb_buff_len) / maxp));
 }
 
+
 static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 		struct urb *urb, int slot_id, unsigned int ep_index)
 {
@@ -3191,17 +3182,12 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 		}
 
 		/* Set the TRB length, TD size, and interrupter fields. */
-		if (xhci->hci_version < 0x100) {
-			remainder = xhci_td_remainder(
-					urb->transfer_buffer_length -
-					running_total);
-		} else {
-			remainder = xhci_v1_0_td_remainder(running_total,
-					trb_buff_len, total_packet_count, urb,
-					num_trbs - 1);
-		}
+		remainder = xhci_td_remainder(xhci, running_total, trb_buff_len,
+					   urb->transfer_buffer_length,
+					   urb, num_trbs - 1);
+
 		length_field = TRB_LEN(trb_buff_len) |
-			remainder |
+			TRB_TD_SIZE(remainder) |
 			TRB_INTR_TARGET(0);
 
 		if (num_trbs > 1)
@@ -3364,17 +3350,12 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 			field |= TRB_ISP;
 
 		/* Set the TRB length, TD size, and interrupter fields. */
-		if (xhci->hci_version < 0x100) {
-			remainder = xhci_td_remainder(
-					urb->transfer_buffer_length -
-					running_total);
-		} else {
-			remainder = xhci_v1_0_td_remainder(running_total,
-					trb_buff_len, total_packet_count, urb,
-					num_trbs - 1);
-		}
+		remainder = xhci_td_remainder(xhci, running_total, trb_buff_len,
+					   urb->transfer_buffer_length,
+					   urb, num_trbs - 1);
+
 		length_field = TRB_LEN(trb_buff_len) |
-			remainder |
+			TRB_TD_SIZE(remainder) |
 			TRB_INTR_TARGET(0);
 
 		if (num_trbs > 1)
@@ -3412,7 +3393,7 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 	struct usb_ctrlrequest *setup;
 	struct xhci_generic_trb *start_trb;
 	int start_cycle;
-	u32 field, length_field;
+	u32 field, length_field, remainder;
 	struct urb_priv *urb_priv;
 	struct xhci_td *td;
 
@@ -3485,9 +3466,15 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 	else
 		field = TRB_TYPE(TRB_DATA);
 
+	remainder = xhci_td_remainder(xhci, 0,
+				   urb->transfer_buffer_length,
+				   urb->transfer_buffer_length,
+				   urb, 1);
+
 	length_field = TRB_LEN(urb->transfer_buffer_length) |
-		xhci_td_remainder(urb->transfer_buffer_length) |
+		TRB_TD_SIZE(remainder) |
 		TRB_INTR_TARGET(0);
+
 	if (urb->transfer_buffer_length > 0) {
 		if (setup->bRequestType & USB_DIR_IN)
 			field |= TRB_DIR_IN;
@@ -3816,17 +3803,12 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 				trb_buff_len = td_remain_len;
 
 			/* Set the TRB length, TD size, & interrupter fields. */
-			if (xhci->hci_version < 0x100) {
-				remainder = xhci_td_remainder(
-						td_len - running_total);
-			} else {
-				remainder = xhci_v1_0_td_remainder(
-						running_total, trb_buff_len,
-						total_packet_count, urb,
-						(trbs_per_td - j - 1));
-			}
+			remainder = xhci_td_remainder(xhci, running_total,
+						   trb_buff_len, td_len,
+						   urb, trbs_per_td - j - 1);
+
 			length_field = TRB_LEN(trb_buff_len) |
-				remainder |
+				TRB_TD_SIZE(remainder) |
 				TRB_INTR_TARGET(0);
 
 			queue_trb(xhci, ep_ring, more_trbs_coming,
drivers/usb/host/xhci.h +0 -0
index dbda41e..ea8b904 100644

drivers/usb/host/xhci.h enum xhci_setup_dev { · line 1143

Quoted 8 lines
drivers/usb/host/xhci.h +2 -0
@@ -1136,6 +1136,8 @@ enum xhci_setup_dev {
 /* Normal TRB fields */
 /* transfer_len bitmasks - bits 0:16 */
 #define	TRB_LEN(p)		((p) & 0x1ffff)
+/* TD Size, packets remaining in this TD, bits 21:17 (5 bits, so max 31) */
+#define TRB_TD_SIZE(p)          (min((p), (u32)31) << 17)
 /* Interrupter Target - which MSI-X vector to target the completion event at */
 #define TRB_INTR_TARGET(p)	(((p) & 0x3ff) << 22)
 #define GET_INTR_TARGET(p)	(((p) >> 22) & 0x3ff)

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html

#15 lore raw

Re: [PATCH] xhci: create one unified function to calculate TRB TD remainder.

Quoted 73 lines · chunfeng yun

Hi,

Quoted 71 lines · Mathias Nyman

xhci versions 1.0 and later report the untransferred data remaining in a TD a bit differently than older hosts.

We used to have separate functions for these, and needed to check host
version before calling the right function.

Now Mediatek host has an additional quirk on how it uses the TD Size field for remaining data. To prevent yet another function for calculating remainder we instead want to make one quirk friendly unified function.

---
  drivers/usb/host/xhci-ring.c | 106 ++++++++++++++++++-------------------------
  drivers/usb/host/xhci.h      |   2 +
  2 files changed, 46 insertions(+), 62 deletions(-)
drivers/usb/host/xhci-ring.c +16 -20
index a47a1e8..57f40a1 100644
@@ -3020,21 +3020,6 @@ int xhci_queue_intr_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
  }
 
  /*
- * The TD size is the number of bytes remaining in the TD (including this TRB),
- * right shifted by 10.
- * It must fit in bits 21:17, so it can't be bigger than 31.
- */
-static u32 xhci_td_remainder(unsigned int remainder)
-{
-	u32 max = (1 << (21 - 17 + 1)) - 1;
-
-	if ((remainder >> 10) >= max)
-		return max << 17;
-	else
-		return (remainder >> 10) << 17;
-}
-
-/*
   * For xHCI 1.0 host controllers, TD size is the number of max packet sized
   * packets remaining in the TD (*not* including this TRB).
   *
@@ -3046,30 +3031,36 @@ static u32 xhci_td_remainder(unsigned int remainder)
   *
   * TD size = total_packet_count - packets_transferred
   *
- * It must fit in bits 21:17, so it can't be bigger than 31.
+ * For xHCI 0.96 and older, TD size field should be the remaining bytes
+ * including this TRB, right shifted by 10
+ *
+ * For all hosts it must fit in bits 21:17, so it can't be bigger than 31.
+ * This is taken care of in the TRB_TD_SIZE() macro
+ *
   * The last TRB in a TD must have the TD size set to zero.
   */
-static u32 xhci_v1_0_td_remainder(int running_total, int trb_buff_len,
-		unsigned int total_packet_count, struct urb *urb,
-		unsigned int num_trbs_left)
+static u32 xhci_td_remainder(struct xhci_hcd *xhci, int transferred,
+			      int trb_buff_len, unsigned int td_total_len,
+			      struct urb *urb, unsigned int num_trbs_left)
  {
-	int packets_transferred;
+	u32 maxp, total_packet_count;
+
+	if (xhci->hci_version < 0x100)
+		return ((td_total_len - transferred) >> 10);
+
+	maxp = GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
+	total_packet_count = DIV_ROUND_UP(td_total_len, maxp);
 
Quoted 9 lines

drivers/usb/host/xhci-ring.c static u32 xhci_td_remainder(unsigned int remainder) · line 3058

Quoted 6 lines
drivers/usb/host/xhci-ring.c +2 -1
  	/* One TRB with a zero-length data packet. */
-	if (num_trbs_left == 0 || (running_total == 0 && trb_buff_len == 0))
+	if (num_trbs_left == 0 || (transferred == 0 && trb_buff_len == 0) ||
+	    trb_buff_len == td_total_len)
  		return 0;
 

I think when trb_buff_len == td_total_len, the TD only needs one trb, so num_trbs_left will equal to 0; that means no need add this condition.

Sorry about the really long delay, I had to focus on other things for a while.

You're right, but I didn't want to change the functionality of the old code.

For some reason the old code called xhci_td_remainder() for both older (0.9) and newer (>= 1.0) xhci hosts in the control transfer case.
I wanted the outcome to stay the same as with the old code, With the old code the TD size of a control tranfers was usually 0, without the additional check we would end up with a remainder of "1". (as num_trbs_left is one)

This should enable easier TD size quirking for control transfers

I'll add the tested-by tag you sent in a later mail

-Mathias

author maintainer
#16 lore raw

Re: [PATCH] xhci: create one unified function to calculate TRB TD remainder.

In reply to Mathias Nyman

Hi,

It works ok when I add MTK's quirk into xhci_td_remainder(), and test it by usb camera, udisk, usb ethernet adapter, and hub.

Quoted 202 lines · Mathias Nyman

xhci versions 1.0 and later report the untransferred data remaining in a TD a bit differently than older hosts.

We used to have separate functions for these, and needed to check host
version before calling the right function.

Now Mediatek host has an additional quirk on how it uses the TD Size field for remaining data. To prevent yet another function for calculating remainder we instead want to make one quirk friendly unified function.

---
 drivers/usb/host/xhci-ring.c | 106 ++++++++++++++++++-------------------------
 drivers/usb/host/xhci.h      |   2 +
 2 files changed, 46 insertions(+), 62 deletions(-)
drivers/usb/host/xhci-ring.c +44 -62
index a47a1e8..57f40a1 100644
@@ -3020,21 +3020,6 @@ int xhci_queue_intr_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 }
 
 /*
- * The TD size is the number of bytes remaining in the TD (including this TRB),
- * right shifted by 10.
- * It must fit in bits 21:17, so it can't be bigger than 31.
- */
-static u32 xhci_td_remainder(unsigned int remainder)
-{
-	u32 max = (1 << (21 - 17 + 1)) - 1;
-
-	if ((remainder >> 10) >= max)
-		return max << 17;
-	else
-		return (remainder >> 10) << 17;
-}
-
-/*
  * For xHCI 1.0 host controllers, TD size is the number of max packet sized
  * packets remaining in the TD (*not* including this TRB).
  *
@@ -3046,30 +3031,36 @@ static u32 xhci_td_remainder(unsigned int remainder)
  *
  * TD size = total_packet_count - packets_transferred
  *
- * It must fit in bits 21:17, so it can't be bigger than 31.
+ * For xHCI 0.96 and older, TD size field should be the remaining bytes
+ * including this TRB, right shifted by 10
+ *
+ * For all hosts it must fit in bits 21:17, so it can't be bigger than 31.
+ * This is taken care of in the TRB_TD_SIZE() macro
+ *
  * The last TRB in a TD must have the TD size set to zero.
  */
-static u32 xhci_v1_0_td_remainder(int running_total, int trb_buff_len,
-		unsigned int total_packet_count, struct urb *urb,
-		unsigned int num_trbs_left)
+static u32 xhci_td_remainder(struct xhci_hcd *xhci, int transferred,
+			      int trb_buff_len, unsigned int td_total_len,
+			      struct urb *urb, unsigned int num_trbs_left)
 {
-	int packets_transferred;
+	u32 maxp, total_packet_count;
+
+	if (xhci->hci_version < 0x100)
+		return ((td_total_len - transferred) >> 10);
+
+	maxp = GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
+	total_packet_count = DIV_ROUND_UP(td_total_len, maxp);
 
 	/* One TRB with a zero-length data packet. */
-	if (num_trbs_left == 0 || (running_total == 0 && trb_buff_len == 0))
+	if (num_trbs_left == 0 || (transferred == 0 && trb_buff_len == 0) ||
+	    trb_buff_len == td_total_len)
 		return 0;
 
-	/* All the TRB queueing functions don't count the current TRB in
-	 * running_total.
-	 */
-	packets_transferred = (running_total + trb_buff_len) /
-		GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
-
-	if ((total_packet_count - packets_transferred) > 31)
-		return 31 << 17;
-	return (total_packet_count - packets_transferred) << 17;
+	/* Queueing functions don't count the current TRB into transferred */
+	return (total_packet_count - ((transferred + trb_buff_len) / maxp));
 }
 
+
 static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 		struct urb *urb, int slot_id, unsigned int ep_index)
 {
@@ -3191,17 +3182,12 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 		}
 
 		/* Set the TRB length, TD size, and interrupter fields. */
-		if (xhci->hci_version < 0x100) {
-			remainder = xhci_td_remainder(
-					urb->transfer_buffer_length -
-					running_total);
-		} else {
-			remainder = xhci_v1_0_td_remainder(running_total,
-					trb_buff_len, total_packet_count, urb,
-					num_trbs - 1);
-		}
+		remainder = xhci_td_remainder(xhci, running_total, trb_buff_len,
+					   urb->transfer_buffer_length,
+					   urb, num_trbs - 1);
+
 		length_field = TRB_LEN(trb_buff_len) |
-			remainder |
+			TRB_TD_SIZE(remainder) |
 			TRB_INTR_TARGET(0);
 
 		if (num_trbs > 1)
@@ -3364,17 +3350,12 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 			field |= TRB_ISP;
 
 		/* Set the TRB length, TD size, and interrupter fields. */
-		if (xhci->hci_version < 0x100) {
-			remainder = xhci_td_remainder(
-					urb->transfer_buffer_length -
-					running_total);
-		} else {
-			remainder = xhci_v1_0_td_remainder(running_total,
-					trb_buff_len, total_packet_count, urb,
-					num_trbs - 1);
-		}
+		remainder = xhci_td_remainder(xhci, running_total, trb_buff_len,
+					   urb->transfer_buffer_length,
+					   urb, num_trbs - 1);
+
 		length_field = TRB_LEN(trb_buff_len) |
-			remainder |
+			TRB_TD_SIZE(remainder) |
 			TRB_INTR_TARGET(0);
 
 		if (num_trbs > 1)
@@ -3412,7 +3393,7 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 	struct usb_ctrlrequest *setup;
 	struct xhci_generic_trb *start_trb;
 	int start_cycle;
-	u32 field, length_field;
+	u32 field, length_field, remainder;
 	struct urb_priv *urb_priv;
 	struct xhci_td *td;
 
@@ -3485,9 +3466,15 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 	else
 		field = TRB_TYPE(TRB_DATA);
 
+	remainder = xhci_td_remainder(xhci, 0,
+				   urb->transfer_buffer_length,
+				   urb->transfer_buffer_length,
+				   urb, 1);
+
 	length_field = TRB_LEN(urb->transfer_buffer_length) |
-		xhci_td_remainder(urb->transfer_buffer_length) |
+		TRB_TD_SIZE(remainder) |
 		TRB_INTR_TARGET(0);
+
 	if (urb->transfer_buffer_length > 0) {
 		if (setup->bRequestType & USB_DIR_IN)
 			field |= TRB_DIR_IN;
@@ -3816,17 +3803,12 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 				trb_buff_len = td_remain_len;
 
 			/* Set the TRB length, TD size, & interrupter fields. */
-			if (xhci->hci_version < 0x100) {
-				remainder = xhci_td_remainder(
-						td_len - running_total);
-			} else {
-				remainder = xhci_v1_0_td_remainder(
-						running_total, trb_buff_len,
-						total_packet_count, urb,
-						(trbs_per_td - j - 1));
-			}
+			remainder = xhci_td_remainder(xhci, running_total,
+						   trb_buff_len, td_len,
+						   urb, trbs_per_td - j - 1);
+
 			length_field = TRB_LEN(trb_buff_len) |
-				remainder |
+				TRB_TD_SIZE(remainder) |
 				TRB_INTR_TARGET(0);
 
 			queue_trb(xhci, ep_ring, more_trbs_coming,
drivers/usb/host/xhci.h +2 -0
index dbda41e..ea8b904 100644
@@ -1136,6 +1136,8 @@ enum xhci_setup_dev {
 /* Normal TRB fields */
 /* transfer_len bitmasks - bits 0:16 */
 #define	TRB_LEN(p)		((p) & 0x1ffff)
+/* TD Size, packets remaining in this TD, bits 21:17 (5 bits, so max 31) */
+#define TRB_TD_SIZE(p)          (min((p), (u32)31) << 17)
 /* Interrupter Target - which MSI-X vector to target the completion event at */
 #define TRB_INTR_TARGET(p)	(((p) & 0x3ff) << 22)
 #define GET_INTR_TARGET(p)	(((p) >> 22) & 0x3ff)
author maintainer Tested-by on v1 1/1
#17 lore raw

Re: [PATCH] xhci: create one unified function to calculate TRB TD remainder.

In reply to Mathias Nyman
Quoted 6 lines · Mathias Nyman

xhci versions 1.0 and later report the untransferred data remaining in a TD a bit differently than older hosts.

We used to have separate functions for these, and needed to check host
version before calling the right function.

Quoted 6 lines

Now Mediatek host has an additional quirk on how it uses the TD Size field for remaining data. To prevent yet another function for calculating remainder we instead want to make one quirk friendly unified function.

---

Quoted 190 lines
 drivers/usb/host/xhci-ring.c | 106 ++++++++++++++++++-------------------------
 drivers/usb/host/xhci.h      |   2 +
 2 files changed, 46 insertions(+), 62 deletions(-)
drivers/usb/host/xhci-ring.c +44 -62
index a47a1e8..57f40a1 100644
@@ -3020,21 +3020,6 @@ int xhci_queue_intr_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 }
 
 /*
- * The TD size is the number of bytes remaining in the TD (including this TRB),
- * right shifted by 10.
- * It must fit in bits 21:17, so it can't be bigger than 31.
- */
-static u32 xhci_td_remainder(unsigned int remainder)
-{
-	u32 max = (1 << (21 - 17 + 1)) - 1;
-
-	if ((remainder >> 10) >= max)
-		return max << 17;
-	else
-		return (remainder >> 10) << 17;
-}
-
-/*
  * For xHCI 1.0 host controllers, TD size is the number of max packet sized
  * packets remaining in the TD (*not* including this TRB).
  *
@@ -3046,30 +3031,36 @@ static u32 xhci_td_remainder(unsigned int remainder)
  *
  * TD size = total_packet_count - packets_transferred
  *
- * It must fit in bits 21:17, so it can't be bigger than 31.
+ * For xHCI 0.96 and older, TD size field should be the remaining bytes
+ * including this TRB, right shifted by 10
+ *
+ * For all hosts it must fit in bits 21:17, so it can't be bigger than 31.
+ * This is taken care of in the TRB_TD_SIZE() macro
+ *
  * The last TRB in a TD must have the TD size set to zero.
  */
-static u32 xhci_v1_0_td_remainder(int running_total, int trb_buff_len,
-		unsigned int total_packet_count, struct urb *urb,
-		unsigned int num_trbs_left)
+static u32 xhci_td_remainder(struct xhci_hcd *xhci, int transferred,
+			      int trb_buff_len, unsigned int td_total_len,
+			      struct urb *urb, unsigned int num_trbs_left)
 {
-	int packets_transferred;
+	u32 maxp, total_packet_count;
+
+	if (xhci->hci_version < 0x100)
+		return ((td_total_len - transferred) >> 10);
+
+	maxp = GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
+	total_packet_count = DIV_ROUND_UP(td_total_len, maxp);
 
 	/* One TRB with a zero-length data packet. */
-	if (num_trbs_left == 0 || (running_total == 0 && trb_buff_len == 0))
+	if (num_trbs_left == 0 || (transferred == 0 && trb_buff_len == 0) ||
+	    trb_buff_len == td_total_len)
 		return 0;
 
-	/* All the TRB queueing functions don't count the current TRB in
-	 * running_total.
-	 */
-	packets_transferred = (running_total + trb_buff_len) /
-		GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
-
-	if ((total_packet_count - packets_transferred) > 31)
-		return 31 << 17;
-	return (total_packet_count - packets_transferred) << 17;
+	/* Queueing functions don't count the current TRB into transferred */
+	return (total_packet_count - ((transferred + trb_buff_len) / maxp));
 }
 
+
 static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 		struct urb *urb, int slot_id, unsigned int ep_index)
 {
@@ -3191,17 +3182,12 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 		}
 
 		/* Set the TRB length, TD size, and interrupter fields. */
-		if (xhci->hci_version < 0x100) {
-			remainder = xhci_td_remainder(
-					urb->transfer_buffer_length -
-					running_total);
-		} else {
-			remainder = xhci_v1_0_td_remainder(running_total,
-					trb_buff_len, total_packet_count, urb,
-					num_trbs - 1);
-		}
+		remainder = xhci_td_remainder(xhci, running_total, trb_buff_len,
+					   urb->transfer_buffer_length,
+					   urb, num_trbs - 1);
+
 		length_field = TRB_LEN(trb_buff_len) |
-			remainder |
+			TRB_TD_SIZE(remainder) |
 			TRB_INTR_TARGET(0);
 
 		if (num_trbs > 1)
@@ -3364,17 +3350,12 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 			field |= TRB_ISP;
 
 		/* Set the TRB length, TD size, and interrupter fields. */
-		if (xhci->hci_version < 0x100) {
-			remainder = xhci_td_remainder(
-					urb->transfer_buffer_length -
-					running_total);
-		} else {
-			remainder = xhci_v1_0_td_remainder(running_total,
-					trb_buff_len, total_packet_count, urb,
-					num_trbs - 1);
-		}
+		remainder = xhci_td_remainder(xhci, running_total, trb_buff_len,
+					   urb->transfer_buffer_length,
+					   urb, num_trbs - 1);
+
 		length_field = TRB_LEN(trb_buff_len) |
-			remainder |
+			TRB_TD_SIZE(remainder) |
 			TRB_INTR_TARGET(0);
 
 		if (num_trbs > 1)
@@ -3412,7 +3393,7 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 	struct usb_ctrlrequest *setup;
 	struct xhci_generic_trb *start_trb;
 	int start_cycle;
-	u32 field, length_field;
+	u32 field, length_field, remainder;
 	struct urb_priv *urb_priv;
 	struct xhci_td *td;
 
@@ -3485,9 +3466,15 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 	else
 		field = TRB_TYPE(TRB_DATA);
 
+	remainder = xhci_td_remainder(xhci, 0,
+				   urb->transfer_buffer_length,
+				   urb->transfer_buffer_length,
+				   urb, 1);
+
 	length_field = TRB_LEN(urb->transfer_buffer_length) |
-		xhci_td_remainder(urb->transfer_buffer_length) |
+		TRB_TD_SIZE(remainder) |
 		TRB_INTR_TARGET(0);
+
 	if (urb->transfer_buffer_length > 0) {
 		if (setup->bRequestType & USB_DIR_IN)
 			field |= TRB_DIR_IN;
@@ -3816,17 +3803,12 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 				trb_buff_len = td_remain_len;
 
 			/* Set the TRB length, TD size, & interrupter fields. */
-			if (xhci->hci_version < 0x100) {
-				remainder = xhci_td_remainder(
-						td_len - running_total);
-			} else {
-				remainder = xhci_v1_0_td_remainder(
-						running_total, trb_buff_len,
-						total_packet_count, urb,
-						(trbs_per_td - j - 1));
-			}
+			remainder = xhci_td_remainder(xhci, running_total,
+						   trb_buff_len, td_len,
+						   urb, trbs_per_td - j - 1);
+
 			length_field = TRB_LEN(trb_buff_len) |
-				remainder |
+				TRB_TD_SIZE(remainder) |
 				TRB_INTR_TARGET(0);
 
 			queue_trb(xhci, ep_ring, more_trbs_coming,
drivers/usb/host/xhci.h +2 -0
index dbda41e..ea8b904 100644
@@ -1136,6 +1136,8 @@ enum xhci_setup_dev {
 /* Normal TRB fields */
 /* transfer_len bitmasks - bits 0:16 */
 #define	TRB_LEN(p)		((p) & 0x1ffff)
+/* TD Size, packets remaining in this TD, bits 21:17 (5 bits, so max 31) */
+#define TRB_TD_SIZE(p)          (min((p), (u32)31) << 17)
 /* Interrupter Target - which MSI-X vector to target the completion event at */
 #define TRB_INTR_TARGET(p)	(((p) & 0x3ff) << 22)
 #define GET_INTR_TARGET(p)	(((p) >> 22) & 0x3ff)
author maintainer
#18 lore raw

PATCH v7 5/5 arm64: dts: mediatek: add xHCI & usb phy for mt8173

In reply to Chunfeng Yun

add xHCI and phy drivers for MT8173-EVB

---
 arch/arm64/boot/dts/mediatek/mt8173-evb.dts | 16 +++++++++++
 arch/arm64/boot/dts/mediatek/mt8173.dtsi    | 44 +++++++++++++++++++++++++++++
 2 files changed, 60 insertions(+)
arch/arm64/boot/dts/mediatek/mt8173-evb.dts +16 -0
index f433c21..112f3f3 100644
@@ -13,6 +13,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "mt8173.dtsi"
 
 / {
@@ -32,6 +33,15 @@
 	};
 
 	chosen { };
+
+	usb_p1_vbus: regulator at 0 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&pio 130 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 };
 
 &pwrap {
@@ -211,3 +221,9 @@
 &uart0 {
 	status = "okay";
 };
+
+&usb30 {
+	vusb33-supply = <&mt6397_vusb_reg>;
+	vbus-supply = <&usb_p1_vbus>;
+	mediatek,wakeup-src = <1>;
+};
arch/arm64/boot/dts/mediatek/mt8173.dtsi +44 -0

56 lines not on this page · raw message

Signature · 1 line
1.8.1.1.dirty