Skip to contentSkip to conversation

ASoC: simple-card: Update clocks binding for simple-card DAI subnodes

RFC PATCH In review Jyri Sarha 2 participants 4 messages Sep 11, 2015 – Oct 6, 2015 3 messages not in the archive

Subsystems (2)
lore
Share & tools
lore

Jyri Sarha

author
#0 lore raw

RFC PATCH 1/1 ASoC: simple-card: Update clocks binding for simple-card DAI subnodes

The updated binding provides a way to set clock-ID and direction parameters for DAI drivers set_sysclk() call back.

---
I proposed something similar about a year ago, but Mark rejected that at the time. This RFC is to start that discussion again. This time before I do any code changes.

Best regards,
Jyri

 Documentation/devicetree/bindings/sound/simple-card.txt | 17 ++++++++++++++++-
 1 file changed, 16 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/sound/simple-card.txt +16 -1
index cf3979e..d10bf2d 100644
@@ -76,6 +76,7 @@ Optional CPU/CODEC subnodes properties:
 - dai-tdm-slot-num			: Please refer to tdm-slot.txt.
 - dai-tdm-slot-width			: Please refer to tdm-slot.txt.
 - clocks / system-clock-frequency	: specify subnode's clock if needed.
+
 					  it can be specified via "clocks" if system has
 					  clock node (= common clock), or "system-clock-frequency"
 					  (if system doens't support common clock)
@@ -83,7 +84,21 @@ Optional CPU/CODEC subnodes properties:
 					  enabled with clk_prepare_enable()
 					  in dai startup() and disabled with
 					  clk_disable_unprepare() in dai
-					  shutdown().
+					  shutdown(). "system-clock-frequency" 
+					  can also be an array if more than one
+					  clock is described.
+- clock-ids				: An array of clock ID integers,
+					  preferrably defined in DT header.
+					  Each entry corresponds to the same
+					  index postion first in "clocks" and
+					  after the end of clocks array to
+					  "system-clock-frequency" array.
+- clock-dirs				: An array of integers describing
+					  clock directions: CLK_IN (= 0) or
+					  OUT (= 1). Entries in the array
+					  refer to clocks in the same way as
+					  in clock-ids property.
+
 
 Example 1 - single DAI link:
 
Signature · 6 lines
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

A message that is not in the archive (sent off-list or not yet received): 1441977482-29215-1-git-send-email-jsarha-l0cyMroinI0@public.gmane.org

#2 lore raw
Quoted 6 lines · Jyri Sarha

The updated binding provides a way to set clock-ID and direction parameters for DAI drivers set_sysclk() call back.

I proposed something similar about a year ago, but Mark rejected that at the time. This RFC is to start that discussion again. This time before I do any code changes.

What's the use case again? Can we address this by converting the relevant drivers to the clock API (or improving their clock API support)?

A message that is not in the archive (sent off-list or not yet received): [email protected]

author
#4 lore raw
Quoted 5 lines · Mark Brown
Quoted 2 lines · Jyri Sarha

The updated binding provides a way to set clock-ID and direction parameters for DAI drivers set_sysclk() call back.

Quoted 8 lines
Quoted 3 lines

I proposed something similar about a year ago, but Mark rejected that at the time. This RFC is to start that discussion again. This time before I do any code changes.

What's the use case again? Can we address this by converting the relevant drivers to the clock API (or improving their clock API support)?

Sorry, I forgot to reply this earlier. The reason why we need this is the way McASP driver uses and provides clocks for different purposes. The most pressing need is to be able to select if we want to use some external clock pin as an input for McASP clock divider that produces the i2s bit-clock or if we want to use McASP's internal clock source.

There are several other things this binding would allow us, and others with flexible i2s HW, to do. Some TI codecs would also benefit from a flexible way of describing the used clock configuration, but Peter know that part better.

I tried to make the binding as flexible and generic as possible. But I do not currently see any immediate need for more than one set_sysclk() call per dai. I just did not see any reason to not allow it either.

Best regards,
Jyri
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html

A message that is not in the archive (sent off-list or not yet received): [email protected]

#6 lore raw
Quoted 12 lines · Jyri Sarha
Quoted 3 lines · Mark Brown

What's the use case again? Can we address this by converting the relevant drivers to the clock API (or improving their clock API support)?

Sorry, I forgot to reply this earlier. The reason why we need this is the way McASP driver uses and provides clocks for different purposes. The most pressing need is to be able to select if we want to use some external clock pin as an input for McASP clock divider that produces the i2s bit-clock or if we want to use McASP's internal clock source.

Quoted 8 lines

There are several other things this binding would allow us, and others with flexible i2s HW, to do. Some TI codecs would also benefit from a flexible way of describing the used clock configuration, but Peter know that part better.

I tried to make the binding as flexible and generic as possible. But I do not currently see any immediate need for more than one set_sysclk() call per dai. I just did not see any reason to not allow it either.

This explains why you want to do this but what about the clock API portion of the question - it would be good to move the ASoC clocking more into the clock API, this would help integration with wider clock trees.