Skip to contentSkip to conversation

PCI: Add pci_enable_atomic_request

PATCH In review Jay Cornwall 2 participants 9 messages Sep 24, 2015 – May 16, 2016 PCI

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 PCI: Add pci_enable_atomic_request

The PCIe 3.0 AtomicOp (6.15) feature allows atomic transctions to be requested by, routed through and completed by PCIe components. Routing and completion do not require software support. Component support for each is detectable via the DEVCAP2 register.

AtomicOp requests are permitted only if a component's DEVCTL2.ATOMICOP_REQUESTER_ENABLE field is set. This capability cannot be detected but is a no-op if set on a component with no support. These requests can only be serviced if the upstream components support AtomicOp completion and/or routing to a component which does.

A concrete example is the AMD Fiji-class GPU, which is specified to support AtomicOp requests, routed through a PLX 8747 switch (advertising AtomicOp routing) to a Haswell host bridge (advertising AtomicOp completion support). When AtomicOp requests are disabled the GPU logs attempts to initiate requests to an MMIO register for debugging.

Add pci_enable_atomic_request for per-device control over AtomicOp requests. Upstream bridges are checked for AtomicOp routing capability and the call fails if any lack this capability. The root port is checked for AtomicOp completion capabilities and the call fails if it does not support any. Routes to other PCIe components are not checked for AtomicOp routing and completion capabilities.

v2: Check for AtomicOp route to root port with AtomicOp completion
v3: Style fixes

---
 drivers/pci/pci.c             | 70 +++++++++++++++++++++++++++++++++++++++++++
 include/linux/pci.h           |  1 +
 include/uapi/linux/pci_regs.h |  5 ++++
 3 files changed, 76 insertions(+)
drivers/pci/pci.c +70 -0
index 6a9a111..edc56e4 100644
@@ -2453,6 +2453,76 @@ bool pci_acs_path_enabled(struct pci_dev *start,
 }
 
 /**
+ * pci_enable_atomic_request - enable or disable AtomicOp requester
+ * @dev: the PCI device
+ *
+ * Return 0 if the device is capable of generating AtomicOp requests,
+ * all upstream bridges support AtomicOp routing, and the root port supports
+ * 32-bit, 64-bit and/or 128-bit AtomicOp completion, or negative otherwise.
+ */
+int pci_enable_atomic_request(struct pci_dev *dev)
+{
+	struct pci_bus *bus = dev->bus;
+
+	if (!pci_is_pcie(dev))
+		return -EINVAL;
+
+	switch (pci_pcie_type(dev)) {
+	/*
+	 * PCIe 3.0, 6.15 specifies that endpoints and root ports are permitted
+	 * to implement AtomicOp requester capabilities.
+	 */
+	case PCI_EXP_TYPE_ENDPOINT:
+	case PCI_EXP_TYPE_LEG_END:
+	case PCI_EXP_TYPE_RC_END:
+	case PCI_EXP_TYPE_ROOT_PORT:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	while (bus->parent) {
+		struct pci_dev *bridge = bus->self;
+		u32 cap;
+
+		pcie_capability_read_dword(bridge, PCI_EXP_DEVCAP2, &cap);
+
+		switch (pci_pcie_type(bridge)) {
+		/*
+		 * Upstream, downstream and root ports may implement AtomicOp
+		 * routing capabilities. AtomicOp routing via a root port is
+		 * not considered.
+		 */
+		case PCI_EXP_TYPE_UPSTREAM:
+		case PCI_EXP_TYPE_DOWNSTREAM:
+			if (!(cap & PCI_EXP_DEVCAP2_ATOMIC_ROUTING))
+				return -EINVAL;
+			break;
+
+		/*
+		 * Root ports are permitted to implement AtomicOp completion
+		 * capabilities.
+		 */
+		case PCI_EXP_TYPE_ROOT_PORT:
+			if (!(cap & (PCI_EXP_DEVCAP2_ATOMIC_COMP32 |
+				     PCI_EXP_DEVCAP2_ATOMIC_COMP64 |
+				     PCI_EXP_DEVCAP2_ATOMIC_COMP128)))
+				return -EINVAL;
+			break;
+		}
+
+
+		bus = bus->parent;
+	}
+
+	pcie_capability_set_word(dev, PCI_EXP_DEVCTL2,
+				 PCI_EXP_DEVCTL2_ATOMICOP_REQ);
+
+	return 0;
+}
+EXPORT_SYMBOL(pci_enable_atomic_request);
+
+/**
  * pci_swizzle_interrupt_pin - swizzle INTx for device behind bridge
  * @dev: the PCI device
  * @pin: the INTx pin (1=INTA, 2=INTB, 3=INTC, 4=INTD)
include/linux/pci.h +1 -0
index e90eb22..4e50003 100644
@@ -1801,6 +1801,7 @@ void pci_request_acs(void);
 bool pci_acs_enabled(struct pci_dev *pdev, u16 acs_flags);
 bool pci_acs_path_enabled(struct pci_dev *start,
 			  struct pci_dev *end, u16 acs_flags);
+int pci_enable_atomic_request(struct pci_dev *dev);
 
 #define PCI_VPD_LRDT			0x80	/* Large Resource Data Type */
 #define PCI_VPD_LRDT_ID(x)		((x) | PCI_VPD_LRDT)
include/uapi/linux/pci_regs.h +5 -0
index 413417f..013c2bd 100644
@@ -571,6 +571,10 @@
  */
 #define PCI_EXP_DEVCAP2		36	/* Device Capabilities 2 */
 #define  PCI_EXP_DEVCAP2_ARI		0x00000020 /* Alternative Routing-ID */
+#define  PCI_EXP_DEVCAP2_ATOMIC_ROUTING	0x00000040 /* AtomicOp routing */
+#define  PCI_EXP_DEVCAP2_ATOMIC_COMP32	0x00000080 /* 32b AtomicOp completion */
+#define  PCI_EXP_DEVCAP2_ATOMIC_COMP64	0x00000100 /* 64b AtomicOp completion */
+#define  PCI_EXP_DEVCAP2_ATOMIC_COMP128	0x00000200 /* 128b AtomicOp completion*/
 #define  PCI_EXP_DEVCAP2_LTR		0x00000800 /* Latency tolerance reporting */
 #define  PCI_EXP_DEVCAP2_OBFF_MASK	0x000c0000 /* OBFF support mechanism */
 #define  PCI_EXP_DEVCAP2_OBFF_MSG	0x00040000 /* New message signaling */
@@ -578,6 +582,7 @@
 #define PCI_EXP_DEVCTL2		40	/* Device Control 2 */
 #define  PCI_EXP_DEVCTL2_COMP_TIMEOUT	0x000f	/* Completion Timeout Value */
 #define  PCI_EXP_DEVCTL2_ARI		0x0020	/* Alternative Routing-ID */
+#define  PCI_EXP_DEVCTL2_ATOMICOP_REQ	0x0040	/* Allow AtomicOp requests */
 #define  PCI_EXP_DEVCTL2_IDO_REQ_EN	0x0100	/* Allow IDO for requests */
 #define  PCI_EXP_DEVCTL2_IDO_CMP_EN	0x0200	/* Allow IDO for completions */
 #define  PCI_EXP_DEVCTL2_LTR_EN		0x0400	/* Enable LTR mechanism */
Signature · 1 line
1.9.1
#1 lore raw
Quoted 24 lines · Jay Cornwall

The PCIe 3.0 AtomicOp (6.15) feature allows atomic transctions to be requested by, routed through and completed by PCIe components. Routing and completion do not require software support. Component support for each is detectable via the DEVCAP2 register.

AtomicOp requests are permitted only if a component's DEVCTL2.ATOMICOP_REQUESTER_ENABLE field is set. This capability cannot be detected but is a no-op if set on a component with no support. These requests can only be serviced if the upstream components support AtomicOp completion and/or routing to a component which does.

A concrete example is the AMD Fiji-class GPU, which is specified to support AtomicOp requests, routed through a PLX 8747 switch (advertising AtomicOp routing) to a Haswell host bridge (advertising AtomicOp completion support). When AtomicOp requests are disabled the GPU logs attempts to initiate requests to an MMIO register for debugging.

Add pci_enable_atomic_request for per-device control over AtomicOp requests. Upstream bridges are checked for AtomicOp routing capability and the call fails if any lack this capability. The root port is checked for AtomicOp completion capabilities and the call fails if it does not support any. Routes to other PCIe components are not checked for AtomicOp routing and completion capabilities.

Quoted 4 lines

v2: Check for AtomicOp route to root port with AtomicOp completion
v3: Style fixes

Hi Jay,

Is there a user for this new functionality? I don't like to add things that have no apparent user.

Bjorn

Quoted 129 lines
---
 drivers/pci/pci.c             | 70 +++++++++++++++++++++++++++++++++++++++++++
 include/linux/pci.h           |  1 +
 include/uapi/linux/pci_regs.h |  5 ++++
 3 files changed, 76 insertions(+)
drivers/pci/pci.c +70 -0
index 6a9a111..edc56e4 100644
@@ -2453,6 +2453,76 @@ bool pci_acs_path_enabled(struct pci_dev *start,
 }
 
 /**
+ * pci_enable_atomic_request - enable or disable AtomicOp requester
+ * @dev: the PCI device
+ *
+ * Return 0 if the device is capable of generating AtomicOp requests,
+ * all upstream bridges support AtomicOp routing, and the root port supports
+ * 32-bit, 64-bit and/or 128-bit AtomicOp completion, or negative otherwise.
+ */
+int pci_enable_atomic_request(struct pci_dev *dev)
+{
+	struct pci_bus *bus = dev->bus;
+
+	if (!pci_is_pcie(dev))
+		return -EINVAL;
+
+	switch (pci_pcie_type(dev)) {
+	/*
+	 * PCIe 3.0, 6.15 specifies that endpoints and root ports are permitted
+	 * to implement AtomicOp requester capabilities.
+	 */
+	case PCI_EXP_TYPE_ENDPOINT:
+	case PCI_EXP_TYPE_LEG_END:
+	case PCI_EXP_TYPE_RC_END:
+	case PCI_EXP_TYPE_ROOT_PORT:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	while (bus->parent) {
+		struct pci_dev *bridge = bus->self;
+		u32 cap;
+
+		pcie_capability_read_dword(bridge, PCI_EXP_DEVCAP2, &cap);
+
+		switch (pci_pcie_type(bridge)) {
+		/*
+		 * Upstream, downstream and root ports may implement AtomicOp
+		 * routing capabilities. AtomicOp routing via a root port is
+		 * not considered.
+		 */
+		case PCI_EXP_TYPE_UPSTREAM:
+		case PCI_EXP_TYPE_DOWNSTREAM:
+			if (!(cap & PCI_EXP_DEVCAP2_ATOMIC_ROUTING))
+				return -EINVAL;
+			break;
+
+		/*
+		 * Root ports are permitted to implement AtomicOp completion
+		 * capabilities.
+		 */
+		case PCI_EXP_TYPE_ROOT_PORT:
+			if (!(cap & (PCI_EXP_DEVCAP2_ATOMIC_COMP32 |
+				     PCI_EXP_DEVCAP2_ATOMIC_COMP64 |
+				     PCI_EXP_DEVCAP2_ATOMIC_COMP128)))
+				return -EINVAL;
+			break;
+		}
+
+
+		bus = bus->parent;
+	}
+
+	pcie_capability_set_word(dev, PCI_EXP_DEVCTL2,
+				 PCI_EXP_DEVCTL2_ATOMICOP_REQ);
+
+	return 0;
+}
+EXPORT_SYMBOL(pci_enable_atomic_request);
+
+/**
  * pci_swizzle_interrupt_pin - swizzle INTx for device behind bridge
  * @dev: the PCI device
  * @pin: the INTx pin (1=INTA, 2=INTB, 3=INTC, 4=INTD)
include/linux/pci.h +1 -0
index e90eb22..4e50003 100644
@@ -1801,6 +1801,7 @@ void pci_request_acs(void);
 bool pci_acs_enabled(struct pci_dev *pdev, u16 acs_flags);
 bool pci_acs_path_enabled(struct pci_dev *start,
 			  struct pci_dev *end, u16 acs_flags);
+int pci_enable_atomic_request(struct pci_dev *dev);
 
 #define PCI_VPD_LRDT			0x80	/* Large Resource Data Type */
 #define PCI_VPD_LRDT_ID(x)		((x) | PCI_VPD_LRDT)
include/uapi/linux/pci_regs.h +5 -0
index 413417f..013c2bd 100644
@@ -571,6 +571,10 @@
  */
 #define PCI_EXP_DEVCAP2		36	/* Device Capabilities 2 */
 #define  PCI_EXP_DEVCAP2_ARI		0x00000020 /* Alternative Routing-ID */
+#define  PCI_EXP_DEVCAP2_ATOMIC_ROUTING	0x00000040 /* AtomicOp routing */
+#define  PCI_EXP_DEVCAP2_ATOMIC_COMP32	0x00000080 /* 32b AtomicOp completion */
+#define  PCI_EXP_DEVCAP2_ATOMIC_COMP64	0x00000100 /* 64b AtomicOp completion */
+#define  PCI_EXP_DEVCAP2_ATOMIC_COMP128	0x00000200 /* 128b AtomicOp completion*/
 #define  PCI_EXP_DEVCAP2_LTR		0x00000800 /* Latency tolerance reporting */
 #define  PCI_EXP_DEVCAP2_OBFF_MASK	0x000c0000 /* OBFF support mechanism */
 #define  PCI_EXP_DEVCAP2_OBFF_MSG	0x00040000 /* New message signaling */
@@ -578,6 +582,7 @@
 #define PCI_EXP_DEVCTL2		40	/* Device Control 2 */
 #define  PCI_EXP_DEVCTL2_COMP_TIMEOUT	0x000f	/* Completion Timeout Value */
 #define  PCI_EXP_DEVCTL2_ARI		0x0020	/* Alternative Routing-ID */
+#define  PCI_EXP_DEVCTL2_ATOMICOP_REQ	0x0040	/* Allow AtomicOp requests */
 #define  PCI_EXP_DEVCTL2_IDO_REQ_EN	0x0100	/* Allow IDO for requests */
 #define  PCI_EXP_DEVCTL2_IDO_CMP_EN	0x0200	/* Allow IDO for completions */
 #define  PCI_EXP_DEVCTL2_LTR_EN		0x0400	/* Enable LTR mechanism */
Signature · 6 lines
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
#2 lore raw
Quoted 28 lines · Bjorn Helgaas
Quoted 27 lines · Jay Cornwall

The PCIe 3.0 AtomicOp (6.15) feature allows atomic transctions to be requested by, routed through and completed by PCIe components. Routing and completion do not require software support. Component support for each is detectable via the DEVCAP2 register.

AtomicOp requests are permitted only if a component's DEVCTL2.ATOMICOP_REQUESTER_ENABLE field is set. This capability cannot be detected but is a no-op if set on a component with no support. These requests can only be serviced if the upstream components support AtomicOp completion and/or routing to a component which does.

A concrete example is the AMD Fiji-class GPU, which is specified to support AtomicOp requests, routed through a PLX 8747 switch (advertising AtomicOp routing) to a Haswell host bridge (advertising AtomicOp completion support). When AtomicOp requests are disabled the GPU logs attempts to initiate requests to an MMIO register for debugging.

Add pci_enable_atomic_request for per-device control over AtomicOp requests. Upstream bridges are checked for AtomicOp routing capability and the call fails if any lack this capability. The root port is checked for AtomicOp completion capabilities and the call fails if it does not support any. Routes to other PCIe components are not checked for AtomicOp routing and completion capabilities.

v2: Check for AtomicOp route to root port with AtomicOp completion
v3: Style fixes

Quoted 8 lines
Quoted 1 line

Hi Jay,

Is there a user for this new functionality? I don't like to add things that have no apparent user.

Bjorn

The client for this code is scheduled to be upstreamed in drm/amdgpu, but we have some internal restructuring to complete before a patchset will be available.

If you'd prefer, I can resubmit this patch as part of that series when it is ready.

Quoted 146 lines
Quoted 146 lines
---
 drivers/pci/pci.c             | 70 
+++++++++++++++++++++++++++++++++++++++++++
 include/linux/pci.h           |  1 +
 include/uapi/linux/pci_regs.h |  5 ++++
 3 files changed, 76 insertions(+)
drivers/pci/pci.c +5 -0
index 6a9a111..edc56e4 100644
@@ -2453,6 +2453,76 @@ bool pci_acs_path_enabled(struct pci_dev 
 *start,
 }
 
 /**
+ * pci_enable_atomic_request - enable or disable AtomicOp requester
+ * @dev: the PCI device
+ *
+ * Return 0 if the device is capable of generating AtomicOp requests,
+ * all upstream bridges support AtomicOp routing, and the root port 

supports
+ * 32-bit, 64-bit and/or 128-bit AtomicOp completion, or negative otherwise.
+ */

drivers/pci/pci.c +10 -0
+int pci_enable_atomic_request(struct pci_dev *dev)
+{
+	struct pci_bus *bus = dev->bus;
+
+	if (!pci_is_pcie(dev))
+		return -EINVAL;
+
+	switch (pci_pcie_type(dev)) {
+	/*
+	 * PCIe 3.0, 6.15 specifies that endpoints and root ports are 

permitted

drivers/pci/pci.c +53 -0
+	 * to implement AtomicOp requester capabilities.
+	 */
+	case PCI_EXP_TYPE_ENDPOINT:
+	case PCI_EXP_TYPE_LEG_END:
+	case PCI_EXP_TYPE_RC_END:
+	case PCI_EXP_TYPE_ROOT_PORT:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	while (bus->parent) {
+		struct pci_dev *bridge = bus->self;
+		u32 cap;
+
+		pcie_capability_read_dword(bridge, PCI_EXP_DEVCAP2, &cap);
+
+		switch (pci_pcie_type(bridge)) {
+		/*
+		 * Upstream, downstream and root ports may implement AtomicOp
+		 * routing capabilities. AtomicOp routing via a root port is
+		 * not considered.
+		 */
+		case PCI_EXP_TYPE_UPSTREAM:
+		case PCI_EXP_TYPE_DOWNSTREAM:
+			if (!(cap & PCI_EXP_DEVCAP2_ATOMIC_ROUTING))
+				return -EINVAL;
+			break;
+
+		/*
+		 * Root ports are permitted to implement AtomicOp completion
+		 * capabilities.
+		 */
+		case PCI_EXP_TYPE_ROOT_PORT:
+			if (!(cap & (PCI_EXP_DEVCAP2_ATOMIC_COMP32 |
+				     PCI_EXP_DEVCAP2_ATOMIC_COMP64 |
+				     PCI_EXP_DEVCAP2_ATOMIC_COMP128)))
+				return -EINVAL;
+			break;
+		}
+
+
+		bus = bus->parent;
+	}
+
+	pcie_capability_set_word(dev, PCI_EXP_DEVCTL2,
+				 PCI_EXP_DEVCTL2_ATOMICOP_REQ);
+
+	return 0;
+}
+EXPORT_SYMBOL(pci_enable_atomic_request);
+
+/**
  * pci_swizzle_interrupt_pin - swizzle INTx for device behind bridge
  * @dev: the PCI device
  * @pin: the INTx pin (1=INTA, 2=INTB, 3=INTC, 4=INTD)
include/linux/pci.h +1 -0
index e90eb22..4e50003 100644
@@ -1801,6 +1801,7 @@ void pci_request_acs(void);
 bool pci_acs_enabled(struct pci_dev *pdev, u16 acs_flags);
 bool pci_acs_path_enabled(struct pci_dev *start,
 			  struct pci_dev *end, u16 acs_flags);
+int pci_enable_atomic_request(struct pci_dev *dev);
 
 #define PCI_VPD_LRDT			0x80	/* Large Resource Data Type */
 #define PCI_VPD_LRDT_ID(x)		((x) | PCI_VPD_LRDT)
include/uapi/linux/pci_regs.h +1 -0
index 413417f..013c2bd 100644
@@ -571,6 +571,10 @@
  */
 #define PCI_EXP_DEVCAP2		36	/* Device Capabilities 2 */
 #define  PCI_EXP_DEVCAP2_ARI		0x00000020 /* Alternative Routing-ID */
+#define  PCI_EXP_DEVCAP2_ATOMIC_ROUTING	0x00000040 /* AtomicOp 

routing */
+#define PCI_EXP_DEVCAP2_ATOMIC_COMP32 0x00000080 /* 32b AtomicOp
completion */
+#define PCI_EXP_DEVCAP2_ATOMIC_COMP64 0x00000100 /* 64b AtomicOp
completion */
+#define PCI_EXP_DEVCAP2_ATOMIC_COMP128 0x00000200 /* 128b AtomicOp
completion*/
#define PCI_EXP_DEVCAP2_LTR 0x00000800 /* Latency tolerance
reporting */
#define PCI_EXP_DEVCAP2_OBFF_MASK 0x000c0000 /* OBFF support
mechanism */
#define PCI_EXP_DEVCAP2_OBFF_MSG 0x00040000 /* New message signaling
*/

include/uapi/linux/pci_regs.h +0 -0
@@ -578,6 +582,7 @@
 #define PCI_EXP_DEVCTL2		40	/* Device Control 2 */
 #define  PCI_EXP_DEVCTL2_COMP_TIMEOUT	0x000f	/* Completion Timeout 

Value */
#define PCI_EXP_DEVCTL2_ARI 0x0020 /* Alternative Routing-ID */
+#define PCI_EXP_DEVCTL2_ATOMICOP_REQ 0x0040 /* Allow AtomicOp
requests */
#define PCI_EXP_DEVCTL2_IDO_REQ_EN 0x0100 /* Allow IDO for requests
*/
#define PCI_EXP_DEVCTL2_IDO_CMP_EN 0x0200 /* Allow IDO for
completions */
#define PCI_EXP_DEVCTL2_LTR_EN 0x0400 /* Enable LTR mechanism */
--
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Signature · 1 line
Jay Cornwall
#3 lore raw
Quoted 50 lines · Jay Cornwall
Quoted 49 lines · Bjorn Helgaas
Quoted 38 lines · Jay Cornwall

The PCIe 3.0 AtomicOp (6.15) feature allows atomic transctions to be requested
by, routed through and completed by PCIe components. Routing and completion
do not require software support. Component support for each is detectable via
the DEVCAP2 register.

AtomicOp requests are permitted only if a component's DEVCTL2.ATOMICOP_REQUESTER_ENABLE field is set. This capability cannot be
detected but is a no-op if set on a component with no support. These requests
can only be serviced if the upstream components support AtomicOp completion
and/or routing to a component which does.

A concrete example is the AMD Fiji-class GPU, which is specified to support
AtomicOp requests, routed through a PLX 8747 switch (advertising AtomicOp
routing) to a Haswell host bridge (advertising AtomicOp completion support).
When AtomicOp requests are disabled the GPU logs attempts to initiate requests
to an MMIO register for debugging.

Add pci_enable_atomic_request for per-device control over AtomicOp requests.
Upstream bridges are checked for AtomicOp routing capability and the call
fails if any lack this capability. The root port is checked for AtomicOp
completion capabilities and the call fails if it does not support any. Routes to other PCIe components are not checked for AtomicOp routing and
completion capabilities.

Quoted 4 lines

v2: Check for AtomicOp route to root port with AtomicOp completion
v3: Style fixes

Hi Jay,

Is there a user for this new functionality? I don't like to add things that have no apparent user.

Quoted 8 lines
Quoted 1 line

Bjorn

The client for this code is scheduled to be upstreamed in drm/amdgpu, but we have some internal restructuring to complete before a patchset will be available.

If you'd prefer, I can resubmit this patch as part of that series when it is ready.

Yeah, that'd be great, why don't we do that. Thanks!

Bjorn

#4 lore raw
Quoted 57 lines · Bjorn Helgaas
Quoted 56 lines · Jay Cornwall
Quoted 42 lines · Bjorn Helgaas
Quoted 41 lines · Jay Cornwall

The PCIe 3.0 AtomicOp (6.15) feature allows atomic transctions to be requested
by, routed through and completed by PCIe components. Routing and completion
do not require software support. Component support for each is detectable via
the DEVCAP2 register.

AtomicOp requests are permitted only if a component's DEVCTL2.ATOMICOP_REQUESTER_ENABLE field is set. This capability cannot be
detected but is a no-op if set on a component with no support. These requests
can only be serviced if the upstream components support AtomicOp completion
and/or routing to a component which does.

A concrete example is the AMD Fiji-class GPU, which is specified to support
AtomicOp requests, routed through a PLX 8747 switch (advertising AtomicOp
routing) to a Haswell host bridge (advertising AtomicOp completion support).
When AtomicOp requests are disabled the GPU logs attempts to initiate requests
to an MMIO register for debugging.

Add pci_enable_atomic_request for per-device control over AtomicOp requests.
Upstream bridges are checked for AtomicOp routing capability and the call
fails if any lack this capability. The root port is checked for AtomicOp
completion capabilities and the call fails if it does not support any. Routes to other PCIe components are not checked for AtomicOp routing and
completion capabilities.

v2: Check for AtomicOp route to root port with AtomicOp completion
v3: Style fixes

Quoted 8 lines
Quoted 1 line

Hi Jay,

Is there a user for this new functionality? I don't like to add things that have no apparent user.

Bjorn

The client for this code is scheduled to be upstreamed in drm/amdgpu, but we have some internal restructuring to complete before a patchset will be available.

Quoted 6 lines
Quoted 2 lines

If you'd prefer, I can resubmit this patch as part of that series when it is ready.

Yeah, that'd be great, why don't we do that. Thanks!

Bjorn

We've been testing this prior to upstreaming the client code and ran into a problem. When the client driver (amdgpu) is running within a virtual machine on the physical PCI function (not SR-IOV) the hypervisor virtualizes the PCI configuration space and blocks writes to DEVCTL2.ATOMICOP_REQUESTER_ENABLE.

I think the host is intended to manage the PCI configuration space in this model. The client driver cannot run simultaneously on the host and guest. This appears to leave the PCI subsystem as the remaining opportunity to enable this feature.

Would you object to calling pci_enable_atomic_request unconditionally in pci_init_capabilites? On most PCIe devices this should be a no-op but I don't see a way to check for this in the AtomicOp specification.

Signature · 1 line
Jay Cornwall
#5 lore raw
Quoted 71 lines · Jay Cornwall
Quoted 57 lines · Bjorn Helgaas
Quoted 56 lines · Jay Cornwall
Quoted 42 lines · Bjorn Helgaas
Quoted 41 lines · Jay Cornwall

The PCIe 3.0 AtomicOp (6.15) feature allows atomic transctions to be requested
by, routed through and completed by PCIe components. Routing and completion
do not require software support. Component support for each is detectable via
the DEVCAP2 register.

AtomicOp requests are permitted only if a component's DEVCTL2.ATOMICOP_REQUESTER_ENABLE field is set. This capability cannot be
detected but is a no-op if set on a component with no support. These requests
can only be serviced if the upstream components support AtomicOp completion
and/or routing to a component which does.

A concrete example is the AMD Fiji-class GPU, which is specified to support
AtomicOp requests, routed through a PLX 8747 switch (advertising AtomicOp
routing) to a Haswell host bridge (advertising AtomicOp completion support).
When AtomicOp requests are disabled the GPU logs attempts to initiate requests
to an MMIO register for debugging.

Add pci_enable_atomic_request for per-device control over AtomicOp requests.
Upstream bridges are checked for AtomicOp routing capability and the call
fails if any lack this capability. The root port is checked for AtomicOp
completion capabilities and the call fails if it does not support any. Routes to other PCIe components are not checked for AtomicOp routing and
completion capabilities.

v2: Check for AtomicOp route to root port with AtomicOp completion
v3: Style fixes

Quoted 8 lines
Quoted 1 line

Hi Jay,

Is there a user for this new functionality? I don't like to add things that have no apparent user.

Bjorn

The client for this code is scheduled to be upstreamed in drm/amdgpu, but we have some internal restructuring to complete before a patchset will be available.

Quoted 6 lines
Quoted 2 lines

If you'd prefer, I can resubmit this patch as part of that series when it is ready.

Yeah, that'd be great, why don't we do that. Thanks!

Bjorn

We've been testing this prior to upstreaming the client code and ran into a problem. When the client driver (amdgpu) is running within a virtual machine on the physical PCI function (not SR-IOV) the hypervisor virtualizes the PCI configuration space and blocks writes to DEVCTL2.ATOMICOP_REQUESTER_ENABLE.

Quoted 8 lines

I think the host is intended to manage the PCI configuration space in this model. The client driver cannot run simultaneously on the host and guest. This appears to leave the PCI subsystem as the remaining opportunity to enable this feature.

Would you object to calling pci_enable_atomic_request unconditionally in pci_init_capabilites? On most PCIe devices this should be a no-op but I don't see a way to check for this in the AtomicOp specification.

Did you get a chance to look at this?

We're trying to figure out which pieces to upstream for the client (drm/amdgpu) driver. If localising this setting to drivers/pci is acceptable then we can remove the call to pci_enable_atomic_request. If not, we'll have to leave the PCI passthrough case unsupported and upstream the original change with the call to it from drm/amdgpu.

Thanks,

Signature · 1 line
Jay Cornwall
#6 lore raw
In reply to Jay Cornwall
Quoted 76 lines · Jay Cornwall
Quoted 57 lines · Bjorn Helgaas
Quoted 56 lines · Jay Cornwall
Quoted 42 lines · Bjorn Helgaas
Quoted 41 lines · Jay Cornwall

The PCIe 3.0 AtomicOp (6.15) feature allows atomic transctions to be requested
by, routed through and completed by PCIe components. Routing and completion
do not require software support. Component support for each is detectable via
the DEVCAP2 register.

AtomicOp requests are permitted only if a component's DEVCTL2.ATOMICOP_REQUESTER_ENABLE field is set. This capability cannot be
detected but is a no-op if set on a component with no support. These requests
can only be serviced if the upstream components support AtomicOp completion
and/or routing to a component which does.

A concrete example is the AMD Fiji-class GPU, which is specified to support
AtomicOp requests, routed through a PLX 8747 switch (advertising AtomicOp
routing) to a Haswell host bridge (advertising AtomicOp completion support).
When AtomicOp requests are disabled the GPU logs attempts to initiate requests
to an MMIO register for debugging.

Add pci_enable_atomic_request for per-device control over AtomicOp requests.
Upstream bridges are checked for AtomicOp routing capability and the call
fails if any lack this capability. The root port is checked for AtomicOp
completion capabilities and the call fails if it does not support any. Routes to other PCIe components are not checked for AtomicOp routing and
completion capabilities.

v2: Check for AtomicOp route to root port with AtomicOp completion
v3: Style fixes

Quoted 8 lines
Quoted 1 line

Hi Jay,

Is there a user for this new functionality? I don't like to add things that have no apparent user.

Bjorn

The client for this code is scheduled to be upstreamed in drm/amdgpu, but we have some internal restructuring to complete before a patchset will be available.

Quoted 6 lines
Quoted 2 lines

If you'd prefer, I can resubmit this patch as part of that series when it is ready.

Yeah, that'd be great, why don't we do that. Thanks!

Bjorn

We've been testing this prior to upstreaming the client code and ran into a problem. When the client driver (amdgpu) is running within a virtual machine on the physical PCI function (not SR-IOV) the hypervisor virtualizes the PCI configuration space and blocks writes to DEVCTL2.ATOMICOP_REQUESTER_ENABLE.

I think the host is intended to manage the PCI configuration space in this model. The client driver cannot run simultaneously on the host and guest. This appears to leave the PCI subsystem as the remaining opportunity to enable this feature.

Quoted 4 lines

Would you object to calling pci_enable_atomic_request unconditionally in pci_init_capabilites? On most PCIe devices this should be a no-op but I don't see a way to check for this in the AtomicOp specification.

The spec says "discovery of AtomicOp Requester capabilities is outside the scope of this specification" [PCIe r3.0, sec 6.15], so I think the intent is that a driver knows the capability of the device and enables and uses AtomicOps when appropriate.

Once enabled in Device Control 2, a device's use of AtomicOps is competely device-specific. In many cases, the device probably doesn't support AtomicOps, so enabling them would be a no-op. But there could be devices where AtomicOps are nominally supported but untested or broken. Even if we didn't change their drivers, those devices could start using AtomicOps, so I'm not comfortable with the PCI core enabling AtomicOp requests indiscriminately.

I don't know anything about the interface between the hypervisor and the client driver. Is there any opportunity for an ioctl or sysfs file or anything whereby the client could ask the hypervisor to enable AtomicOps?

Bjorn

#7 lore raw
In reply to Jay Cornwall
Quoted 40 lines · Jay Cornwall

The PCIe 3.0 AtomicOp (6.15) feature allows atomic transctions to be requested by, routed through and completed by PCIe components. Routing and completion do not require software support. Component support for each is detectable via the DEVCAP2 register.

AtomicOp requests are permitted only if a component's DEVCTL2.ATOMICOP_REQUESTER_ENABLE field is set. This capability cannot be detected but is a no-op if set on a component with no support. These requests can only be serviced if the upstream components support AtomicOp completion and/or routing to a component which does.

A concrete example is the AMD Fiji-class GPU, which is specified to support AtomicOp requests, routed through a PLX 8747 switch (advertising AtomicOp routing) to a Haswell host bridge (advertising AtomicOp completion support). When AtomicOp requests are disabled the GPU logs attempts to initiate requests to an MMIO register for debugging.

Add pci_enable_atomic_request for per-device control over AtomicOp requests. Upstream bridges are checked for AtomicOp routing capability and the call fails if any lack this capability. The root port is checked for AtomicOp completion capabilities and the call fails if it does not support any. Routes to other PCIe components are not checked for AtomicOp routing and completion capabilities.

v2: Check for AtomicOp route to root port with AtomicOp completion
v3: Style fixes

---
 drivers/pci/pci.c             | 70 +++++++++++++++++++++++++++++++++++++++++++
 include/linux/pci.h           |  1 +
 include/uapi/linux/pci_regs.h |  5 ++++
 3 files changed, 76 insertions(+)
drivers/pci/pci.c +0 -0
index 6a9a111..edc56e4 100644
@@ -2453,6 +2453,76 @@ bool pci_acs_path_enabled(struct pci_dev *start,
 }

drivers/pci/pci.c bool pci_acs_path_enabled(struct pci_dev *start, · line 2463

Quoted 10 lines
drivers/pci/pci.c +8 -0
 
 /**
+ * pci_enable_atomic_request - enable or disable AtomicOp requester
+ * @dev: the PCI device
+ *
+ * Return 0 if the device is capable of generating AtomicOp requests,
+ * all upstream bridges support AtomicOp routing, and the root port supports
+ * 32-bit, 64-bit and/or 128-bit AtomicOp completion, or negative otherwise.
+ */
+int pci_enable_atomic_request(struct pci_dev *dev)

This interface only works for Endpoints that want to generate AtomicOps targeting the Root Complex. We should make this explicit, e.g., by naming it "pci_enable_atomic_ops_to_root" or something.

If we wanted anything else (host-to-device or device-to-device), then we would need to know both ends (requester and completer) before we could figure out whether AtomicOps were even possible.

Quoted 9 lines
drivers/pci/pci.c +9 -0
+{
+	struct pci_bus *bus = dev->bus;
+
+	if (!pci_is_pcie(dev))
+		return -EINVAL;
+
+	switch (pci_pcie_type(dev)) {
+	/*
+	 * PCIe 3.0, 6.15 specifies that endpoints and root ports are permitted

drivers/pci/pci.c bool pci_acs_path_enabled(struct pci_dev *start, · line 2482

Quoted 10 lines
drivers/pci/pci.c +10 -0
+	 * to implement AtomicOp requester capabilities.
+	 */
+	case PCI_EXP_TYPE_ENDPOINT:
+	case PCI_EXP_TYPE_LEG_END:
+	case PCI_EXP_TYPE_RC_END:
+	case PCI_EXP_TYPE_ROOT_PORT:
+		break;
+	default:
+		return -EINVAL;
+	}

This should be a little stricter: we should return error unless "dev" is an Endpoint.

Quoted 6 lines
drivers/pci/pci.c +6 -0
+	while (bus->parent) {
+		struct pci_dev *bridge = bus->self;
+		u32 cap;
+
+		pcie_capability_read_dword(bridge, PCI_EXP_DEVCAP2, &cap);
+

drivers/pci/pci.c bool pci_acs_path_enabled(struct pci_dev *start, · line 2499

Quoted 10 lines
drivers/pci/pci.c +10 -0
+		switch (pci_pcie_type(bridge)) {
+		/*
+		 * Upstream, downstream and root ports may implement AtomicOp
+		 * routing capabilities. AtomicOp routing via a root port is
+		 * not considered.
+		 */
+		case PCI_EXP_TYPE_UPSTREAM:
+		case PCI_EXP_TYPE_DOWNSTREAM:
+			if (!(cap & PCI_EXP_DEVCAP2_ATOMIC_ROUTING))
+				return -EINVAL;

I think we also need to check the AtomicOp Egress Blocking bit. I think this is only applicable for Upstream Ports (Downstream Ports will *receive* AtomicOps from an Endpoint, but egress toward the Root Complex should only be via an Upstream Port).

Side note: we should add "lspci" support for AtomicOp capabilities and control. This can be done any time and isn't dependent on any kernel changes.

Quoted 71 lines
drivers/pci/pci.c +26 -0
+			break;
+
+		/*
+		 * Root ports are permitted to implement AtomicOp completion
+		 * capabilities.
+		 */
+		case PCI_EXP_TYPE_ROOT_PORT:
+			if (!(cap & (PCI_EXP_DEVCAP2_ATOMIC_COMP32 |
+				     PCI_EXP_DEVCAP2_ATOMIC_COMP64 |
+				     PCI_EXP_DEVCAP2_ATOMIC_COMP128)))
+				return -EINVAL;
+			break;
+		}
+
+
+		bus = bus->parent;
+	}
+
+	pcie_capability_set_word(dev, PCI_EXP_DEVCTL2,
+				 PCI_EXP_DEVCTL2_ATOMICOP_REQ);
+
+	return 0;
+}
+EXPORT_SYMBOL(pci_enable_atomic_request);
+
+/**
  * pci_swizzle_interrupt_pin - swizzle INTx for device behind bridge
  * @dev: the PCI device
  * @pin: the INTx pin (1=INTA, 2=INTB, 3=INTC, 4=INTD)
include/linux/pci.h +1 -0
index e90eb22..4e50003 100644
@@ -1801,6 +1801,7 @@ void pci_request_acs(void);
 bool pci_acs_enabled(struct pci_dev *pdev, u16 acs_flags);
 bool pci_acs_path_enabled(struct pci_dev *start,
 			  struct pci_dev *end, u16 acs_flags);
+int pci_enable_atomic_request(struct pci_dev *dev);
 
 #define PCI_VPD_LRDT			0x80	/* Large Resource Data Type */
 #define PCI_VPD_LRDT_ID(x)		((x) | PCI_VPD_LRDT)
include/uapi/linux/pci_regs.h +5 -0
index 413417f..013c2bd 100644
@@ -571,6 +571,10 @@
  */
 #define PCI_EXP_DEVCAP2		36	/* Device Capabilities 2 */
 #define  PCI_EXP_DEVCAP2_ARI		0x00000020 /* Alternative Routing-ID */
+#define  PCI_EXP_DEVCAP2_ATOMIC_ROUTING	0x00000040 /* AtomicOp routing */
+#define  PCI_EXP_DEVCAP2_ATOMIC_COMP32	0x00000080 /* 32b AtomicOp completion */
+#define  PCI_EXP_DEVCAP2_ATOMIC_COMP64	0x00000100 /* 64b AtomicOp completion */
+#define  PCI_EXP_DEVCAP2_ATOMIC_COMP128	0x00000200 /* 128b AtomicOp completion*/
 #define  PCI_EXP_DEVCAP2_LTR		0x00000800 /* Latency tolerance reporting */
 #define  PCI_EXP_DEVCAP2_OBFF_MASK	0x000c0000 /* OBFF support mechanism */
 #define  PCI_EXP_DEVCAP2_OBFF_MSG	0x00040000 /* New message signaling */
@@ -578,6 +582,7 @@
 #define PCI_EXP_DEVCTL2		40	/* Device Control 2 */
 #define  PCI_EXP_DEVCTL2_COMP_TIMEOUT	0x000f	/* Completion Timeout Value */
 #define  PCI_EXP_DEVCTL2_ARI		0x0020	/* Alternative Routing-ID */
+#define  PCI_EXP_DEVCTL2_ATOMICOP_REQ	0x0040	/* Allow AtomicOp requests */
 #define  PCI_EXP_DEVCTL2_IDO_REQ_EN	0x0100	/* Allow IDO for requests */
 #define  PCI_EXP_DEVCTL2_IDO_CMP_EN	0x0200	/* Allow IDO for completions */
 #define  PCI_EXP_DEVCTL2_LTR_EN		0x0400	/* Enable LTR mechanism */
Signature · 6 lines
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
#8 lore raw
Quoted 192 lines · Bjorn Helgaas
Quoted 49 lines · Jay Cornwall

The PCIe 3.0 AtomicOp (6.15) feature allows atomic transctions to be requested by, routed through and completed by PCIe components. Routing and completion do not require software support. Component support for each is detectable via the DEVCAP2 register.

AtomicOp requests are permitted only if a component's DEVCTL2.ATOMICOP_REQUESTER_ENABLE field is set. This capability cannot be detected but is a no-op if set on a component with no support. These requests can only be serviced if the upstream components support AtomicOp completion and/or routing to a component which does.

A concrete example is the AMD Fiji-class GPU, which is specified to support AtomicOp requests, routed through a PLX 8747 switch (advertising AtomicOp routing) to a Haswell host bridge (advertising AtomicOp completion support). When AtomicOp requests are disabled the GPU logs attempts to initiate requests to an MMIO register for debugging.

Add pci_enable_atomic_request for per-device control over AtomicOp requests. Upstream bridges are checked for AtomicOp routing capability and the call fails if any lack this capability. The root port is checked for AtomicOp completion capabilities and the call fails if it does not support any. Routes to other PCIe components are not checked for AtomicOp routing and completion capabilities.

v2: Check for AtomicOp route to root port with AtomicOp completion
v3: Style fixes

---
 drivers/pci/pci.c             | 70 
+++++++++++++++++++++++++++++++++++++++++++
 include/linux/pci.h           |  1 +
 include/uapi/linux/pci_regs.h |  5 ++++
 3 files changed, 76 insertions(+)
drivers/pci/pci.c +5 -0
index 6a9a111..edc56e4 100644
@@ -2453,6 +2453,76 @@ bool pci_acs_path_enabled(struct pci_dev 
 *start,
 }
 
 /**
+ * pci_enable_atomic_request - enable or disable AtomicOp requester
+ * @dev: the PCI device
+ *
+ * Return 0 if the device is capable of generating AtomicOp requests,
+ * all upstream bridges support AtomicOp routing, and the root port 
Quoted 5 lines

supports
+ * 32-bit, 64-bit and/or 128-bit AtomicOp completion, or negative otherwise.
+ */
+int pci_enable_atomic_request(struct pci_dev *dev)

This interface only works for Endpoints that want to generate AtomicOps targeting the Root Complex. We should make this explicit, e.g., by naming it "pci_enable_atomic_ops_to_root" or something.

If we wanted anything else (host-to-device or device-to-device), then we would need to know both ends (requester and completer) before we could figure out whether AtomicOps were even possible.

Quoted 10 lines
drivers/pci/pci.c +9 -0
+{
+	struct pci_bus *bus = dev->bus;
+
+	if (!pci_is_pcie(dev))
+		return -EINVAL;
+
+	switch (pci_pcie_type(dev)) {
+	/*
+	 * PCIe 3.0, 6.15 specifies that endpoints and root ports are 

permitted

drivers/pci/pci.c bool pci_acs_path_enabled(struct pci_dev *start, · line 2482

Quoted 10 lines
drivers/pci/pci.c +10 -0
+	 * to implement AtomicOp requester capabilities.
+	 */
+	case PCI_EXP_TYPE_ENDPOINT:
+	case PCI_EXP_TYPE_LEG_END:
+	case PCI_EXP_TYPE_RC_END:
+	case PCI_EXP_TYPE_ROOT_PORT:
+		break;
+	default:
+		return -EINVAL;
+	}

This should be a little stricter: we should return error unless "dev" is an Endpoint.

Quoted 6 lines
drivers/pci/pci.c +6 -0
+	while (bus->parent) {
+		struct pci_dev *bridge = bus->self;
+		u32 cap;
+
+		pcie_capability_read_dword(bridge, PCI_EXP_DEVCAP2, &cap);
+

drivers/pci/pci.c bool pci_acs_path_enabled(struct pci_dev *start, · line 2499

Quoted 10 lines
drivers/pci/pci.c +10 -0
+		switch (pci_pcie_type(bridge)) {
+		/*
+		 * Upstream, downstream and root ports may implement AtomicOp
+		 * routing capabilities. AtomicOp routing via a root port is
+		 * not considered.
+		 */
+		case PCI_EXP_TYPE_UPSTREAM:
+		case PCI_EXP_TYPE_DOWNSTREAM:
+			if (!(cap & PCI_EXP_DEVCAP2_ATOMIC_ROUTING))
+				return -EINVAL;

I think we also need to check the AtomicOp Egress Blocking bit. I think this is only applicable for Upstream Ports (Downstream Ports will *receive* AtomicOps from an Endpoint, but egress toward the Root Complex should only be via an Upstream Port).

Side note: we should add "lspci" support for AtomicOp capabilities and control. This can be done any time and isn't dependent on any kernel changes.

Quoted 78 lines
drivers/pci/pci.c +26 -0
+			break;
+
+		/*
+		 * Root ports are permitted to implement AtomicOp completion
+		 * capabilities.
+		 */
+		case PCI_EXP_TYPE_ROOT_PORT:
+			if (!(cap & (PCI_EXP_DEVCAP2_ATOMIC_COMP32 |
+				     PCI_EXP_DEVCAP2_ATOMIC_COMP64 |
+				     PCI_EXP_DEVCAP2_ATOMIC_COMP128)))
+				return -EINVAL;
+			break;
+		}
+
+
+		bus = bus->parent;
+	}
+
+	pcie_capability_set_word(dev, PCI_EXP_DEVCTL2,
+				 PCI_EXP_DEVCTL2_ATOMICOP_REQ);
+
+	return 0;
+}
+EXPORT_SYMBOL(pci_enable_atomic_request);
+
+/**
  * pci_swizzle_interrupt_pin - swizzle INTx for device behind bridge
  * @dev: the PCI device
  * @pin: the INTx pin (1=INTA, 2=INTB, 3=INTC, 4=INTD)
include/linux/pci.h +1 -0
index e90eb22..4e50003 100644
@@ -1801,6 +1801,7 @@ void pci_request_acs(void);
 bool pci_acs_enabled(struct pci_dev *pdev, u16 acs_flags);
 bool pci_acs_path_enabled(struct pci_dev *start,
 			  struct pci_dev *end, u16 acs_flags);
+int pci_enable_atomic_request(struct pci_dev *dev);
 
 #define PCI_VPD_LRDT			0x80	/* Large Resource Data Type */
 #define PCI_VPD_LRDT_ID(x)		((x) | PCI_VPD_LRDT)
include/uapi/linux/pci_regs.h +1 -0
index 413417f..013c2bd 100644
@@ -571,6 +571,10 @@
  */
 #define PCI_EXP_DEVCAP2		36	/* Device Capabilities 2 */
 #define  PCI_EXP_DEVCAP2_ARI		0x00000020 /* Alternative Routing-ID */
+#define  PCI_EXP_DEVCAP2_ATOMIC_ROUTING	0x00000040 /* AtomicOp 

routing */
+#define PCI_EXP_DEVCAP2_ATOMIC_COMP32 0x00000080 /* 32b AtomicOp
completion */
+#define PCI_EXP_DEVCAP2_ATOMIC_COMP64 0x00000100 /* 64b AtomicOp
completion */
+#define PCI_EXP_DEVCAP2_ATOMIC_COMP128 0x00000200 /* 128b AtomicOp
completion*/
#define PCI_EXP_DEVCAP2_LTR 0x00000800 /* Latency tolerance
reporting */
#define PCI_EXP_DEVCAP2_OBFF_MASK 0x000c0000 /* OBFF support
mechanism */
#define PCI_EXP_DEVCAP2_OBFF_MSG 0x00040000 /* New message signaling
*/

include/uapi/linux/pci_regs.h +0 -0
@@ -578,6 +582,7 @@
 #define PCI_EXP_DEVCTL2		40	/* Device Control 2 */
 #define  PCI_EXP_DEVCTL2_COMP_TIMEOUT	0x000f	/* Completion Timeout 

Value */
#define PCI_EXP_DEVCTL2_ARI 0x0020 /* Alternative Routing-ID */
+#define PCI_EXP_DEVCTL2_ATOMICOP_REQ 0x0040 /* Allow AtomicOp
requests */
#define PCI_EXP_DEVCTL2_IDO_REQ_EN 0x0100 /* Allow IDO for requests
*/
#define PCI_EXP_DEVCTL2_IDO_CMP_EN 0x0200 /* Allow IDO for
completions */
#define PCI_EXP_DEVCTL2_LTR_EN 0x0400 /* Enable LTR mechanism */
--
1.9.1

Quoted 4 lines
Quoted 4 lines

--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Thanks, I'll send a V4 along with the client patchset once it's ready for upstreaming.

Signature · 1 line
Jay Cornwall