sunxi: Fix sorting of boards in MAINTAINERS
Subsystems (2)
PATCH v2 1/2 sunxi: Fix sorting of boards in MAINTAINERS
--- board/sunxi/MAINTAINERS | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
board/sunxi/MAINTAINERS +1 -1
@@ -29,11 +29,11 @@ F: configs/mk802_a10s_defconfig F: configs/q8_a13_tablet_defconfig F: configs/r7-tv-dongle_defconfig F: configs/UTOO_P66_defconfig +F: configs/Wobo_i5_defconfig F: include/configs/sun6i.h F: configs/CSQ_CS908_defconfig F: configs/Mele_A1000G_quad_defconfig F: configs/Mele_M9_defconfig -F: configs/Wobo_i5_defconfig F: include/configs/sun7i.h F: configs/A20-OLinuXino_MICRO_defconfig F: configs/Bananapi_defconfig
Signature · 1 line
2.5.0
PATCH v2 2/2 sunxi: Add defconfig for the Sinovoip BPI-M2 board
The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features 1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver, stereo headphone jack and hdmi video output.
The dts changes are identical to the dts files submitted upstream.
A few notes on the use if dldo and aldo regulators. DLDO1 is used for Vdd for the ethernet phy, ALDO2 is used for AVdd for the ethernet phy. ALDO1 is used to power the sdio wifi module.
--- arch/arm/dts/Makefile | 3 +- arch/arm/dts/sun6i-a31.dtsi | 18 +++ arch/arm/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 194 ++++++++++++++++++++++++++++ board/sunxi/MAINTAINERS | 1 + configs/Sinovoip_BPI_M2_defconfig | 18 +++ 5 files changed, 233 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/sun6i-a31s-sinovoip-bpi-m2.dts create mode 100644 configs/Sinovoip_BPI_M2_defconfig
arch/arm/dts/Makefile +2 -1
@@ -124,7 +124,8 @@ dtb-$(CONFIG_MACH_SUN6I) += \ sun6i-a31-mele-a1000g-quad.dtb \ sun6i-a31-mixtile-loftq.dtb \ sun6i-a31s-cs908.dtb \ - sun6i-a31s-primo81.dtb + sun6i-a31s-primo81.dtb \ + sun6i-a31s-sinovoip-bpi-m2.dtb dtb-$(CONFIG_MACH_SUN7I) += \ sun7i-a20-ainol-aw1.dtb \ sun7i-a20-bananapi.dtb \
arch/arm/dts/sun6i-a31.dtsi +18 -0
@@ -659,6 +659,24 @@ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + mmc2_pins_a: mmc2 at 0 { + allwinner,pins = "PC6", "PC7", "PC8", "PC9", + "PC10", "PC11"; + allwinner,function = "mmc2"; + allwinner,drive = <SUN4I_PINCTRL_30_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + mmc2_8bit_emmc_pins: mmc2 at 1 { + allwinner,pins = "PC6", "PC7", "PC8", "PC9", + "PC10", "PC11", "PC12", + "PC13", "PC14", "PC15", + "PC24"; + allwinner,function = "mmc2"; + allwinner,drive = <SUN4I_PINCTRL_30_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + gmac_pins_mii_a: gmac_mii at 0 { allwinner,pins = "PA0", "PA1", "PA2", "PA3", "PA8", "PA9", "PA11",
arch/arm/dts/sun6i-a31s-sinovoip-bpi-m2.dts new file +194 -0
194 lines not on this page · raw message
board/sunxi/MAINTAINERS +1 -0
@@ -34,6 +34,7 @@ F: include/configs/sun6i.h F: configs/CSQ_CS908_defconfig F: configs/Mele_A1000G_quad_defconfig F: configs/Mele_M9_defconfig +F: configs/Sinovoip_BPI_M2_defconfig F: include/configs/sun7i.h F: configs/A20-OLinuXino_MICRO_defconfig F: configs/Bananapi_defconfig
configs/Sinovoip_BPI_M2_defconfig new file +18 -0
@@ -0,0 +1,18 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_MACH_SUN6I=y +CONFIG_DRAM_CLK=432 +CONFIG_USB1_VBUS_PIN="" +CONFIG_USB2_VBUS_PIN="" +CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31s-sinovoip-bpi-m2" +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_SPL=y +CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII" +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_FPGA is not set +CONFIG_ETH_DESIGNWARE=y +CONFIG_AXP_DLDO1_VOLT=3000 +CONFIG_AXP_ALDO1_VOLT=3300 +CONFIG_AXP_ALDO2_VOLT=1800 +CONFIG_USB_EHCI_HCD=y
Signature · 1 line
2.5.0
PATCH v2 2/2 sunxi: Add defconfig for the Sinovoip BPI-M2 board
Quoted 5 lines · Hans de Goede
The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features 1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver,
stereo headphone jack and hdmi video output.
Quoted 7 lines
The dts changes are identical to the dts files submitted upstream.
A few notes on the use if dldo and aldo regulators. DLDO1 is used for Vdd for the ethernet phy, ALDO2 is used for AVdd for the ethernet phy. ALDO1 is used to power the sdio wifi module.
Signed-off-by Hans de Goede <[email protected]>
and for the 1/2 as well, which hardly needs an ack IMHO.