Skip to contentSkip to conversation

ARM: dts: Add Advantech board support

PATCH Superseded Akshay Bhat 3 participants 17 messages Nov 5, 2015 – Nov 10, 2015

Subsystems (3)

v2 of 8 Superseded Latest is v8 →

lore
Share & tools
lore
#0 lore raw

v2 cover ARM: dts: Add Advantech board support

This series aims to add Advantech BA-16 module (iMX6 based) and GE board support. Patches 7 to 10 correspond to the v2 changes.

This series has been tested against linux-next tag next-20151105.

Modifications:
v1->v2:
- Move entries from pinctrl_hog to relevant groups as suggested by Lucas Stash
- Remove unused PCIe power-on-gpio entry as suggested by Lucas Stash
- Remove always-on from regulators that do not need to be always-on as suggested by Lucas Stash
- Enable support for mma8453
- Add vendor prefix for General Electric Company as suggested by Martin Donnelly
- Update Copyright information as suggest by Martin Donnelly

History:
--------
[v1]: http://lists.infradead.org/pipermail/linux-arm-kernel/2015-October/381872.html

Akshay Bhat (8):
of: Add vendor prefix for Advantech Corporation
ARM: dts: imx: Add support for Advantech/GE B450v3
ARM: dts: imx: Add support for Advantech/GE B650v3
ARM: dts: imx: Add support for Advantech/GE B850v3
of: Add vendor prefix for General Electric Company
ARM: dts: imx: Update vendor info for GE Bx50v3 boards
ARM: dts: imx: Add mma8453 support
ARM: dts: imx6q-ba16: Cleanup pinctrl and LDO

Justin Waters (2):
ARM: dts: imx: Add Advantech BA-16 Qseven module
ARM: dts: imx: Add support for Advantech/GE Bx50v3

 .../devicetree/bindings/vendor-prefixes.txt        |   2 +
 arch/arm/boot/dts/Makefile                         |   3 +
 arch/arm/boot/dts/imx6q-b450v3.dts                 |  75 +++
 arch/arm/boot/dts/imx6q-b650v3.dts                 |  74 +++
 arch/arm/boot/dts/imx6q-b850v3.dts                 | 122 +++++
 arch/arm/boot/dts/imx6q-ba16.dtsi                  | 584 +++++++++++++++++++++
 arch/arm/boot/dts/imx6q-bx50v3.dtsi                | 211 ++++++++
 7 files changed, 1071 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-b450v3.dts
 create mode 100644 arch/arm/boot/dts/imx6q-b650v3.dts
 create mode 100644 arch/arm/boot/dts/imx6q-b850v3.dts
 create mode 100644 arch/arm/boot/dts/imx6q-ba16.dtsi
 create mode 100644 arch/arm/boot/dts/imx6q-bx50v3.dtsi
Signature · 1 line
2.6.2
#1 lore raw

PATCH v2 1/10 of: Add vendor prefix for Advantech Corporation

This patch adds vendor prefix for Advantech Corporation.

Website: http://www.advantech.com/

---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/vendor-prefixes.txt +1 -0
index 55df1d4..2b3c5ac 100644
@@ -10,6 +10,7 @@ ad	Avionic Design GmbH
 adapteva	Adapteva, Inc.
 adh	AD Holdings Plc.
 adi	Analog Devices, Inc.
+adv	Advantech Corporation
 aeroflexgaisler	Aeroflex Gaisler AB
 al	Annapurna Labs
 allwinner	Allwinner Technology Co., Ltd.
Signature · 1 line
2.6.2
maintainer
#2 lore raw

PATCH v2 1/10 of: Add vendor prefix for Advantech Corporation

Quoted 13 lines · Akshay Bhat

This patch adds vendor prefix for Advantech Corporation.

Website: http://www.advantech.com/

---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/vendor-prefixes.txt +0 -0
index 55df1d4..2b3c5ac 100644

Documentation/devicetree/bindings/vendor-prefixes.txt ad Avionic Design GmbH · line 13

Quoted 4 lines
Documentation/devicetree/bindings/vendor-prefixes.txt +1 -0
@@ -10,6 +10,7 @@ ad	Avionic Design GmbH
 adapteva	Adapteva, Inc.
 adh	AD Holdings Plc.
 adi	Analog Devices, Inc.
+adv	Advantech Corporation

adv is a bit short. I think it would be better to go with "advantech".

Rob

Quoted 6 lines
Documentation/devicetree/bindings/vendor-prefixes.txt +0 -0
 aeroflexgaisler	Aeroflex Gaisler AB
 al	Annapurna Labs
 allwinner	Allwinner Technology Co., Ltd.
Signature · 1 line
2.6.2
#3 lore raw

PATCH v2 1/10 of: Add vendor prefix for Advantech Corporation

Quoted 21 lines · Rob Herring
Quoted 13 lines · Akshay Bhat

This patch adds vendor prefix for Advantech Corporation.

Website: http://www.advantech.com/

---
  Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
  1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/vendor-prefixes.txt +0 -0
index 55df1d4..2b3c5ac 100644

Documentation/devicetree/bindings/vendor-prefixes.txt ad Avionic Design GmbH · line 13

Quoted 4 lines
Documentation/devicetree/bindings/vendor-prefixes.txt +1 -0
@@ -10,6 +10,7 @@ ad	Avionic Design GmbH
  adapteva	Adapteva, Inc.
  adh	AD Holdings Plc.
  adi	Analog Devices, Inc.
+adv	Advantech Corporation

adv is a bit short. I think it would be better to go with "advantech".

Quoted 2 lines

Rob

Fixed in v3.

http://lists.infradead.org/pipermail/linux-arm-kernel/2015-November/384203.html

Quoted 6 lines
Quoted 6 lines
Documentation/devicetree/bindings/vendor-prefixes.txt +0 -1
  aeroflexgaisler	Aeroflex Gaisler AB
  al	Annapurna Labs
  allwinner	Allwinner Technology Co., Ltd.
--

2.6.2

#4 lore raw

PATCH v2 2/10 ARM: dts: imx: Add Advantech BA-16 Qseven module

In reply to Akshay Bhat

From: Justin Waters <[email protected]>

Add support for Advantech BA-16 module based on iMX6D processor

http://www2.advantech.com/products/medical_computing_system/dms-ba16/mod_64aa1566-169c-483d-97c8-c2c22c163fc3.aspx

---
 arch/arm/boot/dts/imx6q-ba16.dtsi | 559 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 559 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-ba16.dtsi
arch/arm/boot/dts/imx6q-ba16.dtsi new file +559 -0
new file mode 100644
index 0000000..3d47039
@@ -0,0 +1,559 @@
+/*
+ * Support for imx6 based Advantech DMS-BA16 Qseven module
+ *
+ * Copyright 2015 Timesys Corporation.
+ * Copyright 2015 GE Healthcare.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "imx6q.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	memory {
+		reg = <0x10000000 0x40000000>;
+	};
+
+	clocks {
+		clk24m: clk24m {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <24000000>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_usb_otg_vbus: regulator at 1 {
+			compatible = "regulator-fixed";
+			regulator-name = "usb_otg_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+		};
+
+		reg_usb_h1_vbus: regulator at 2 {
+			compatible = "regulator-fixed";
+			regulator-name = "usb_h1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+		};
+
+		reg_1p8v: regulator at 3 {
+			compatible = "regulator-fixed";
+			regulator-name = "1P8V";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		reg_3p3v: regulator at 4 {
+			compatible = "regulator-fixed";
+			regulator-name = "3P3V";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		lvds_ppen: regulator at 5 {
+			compatible = "regulator-fixed";
+			regulator-name = "lvds_ppen";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+			gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000>;
+		brightness-levels = <  0   1   2   3   4   5   6   7   8   9
+				      10  11  12  13  14  15  16  17  18  19
+				      20  21  22  23  24  25  26  27  28  29
+				      30  31  32  33  34  35  36  37  38  39
+				      40  41  42  43  44  45  46  47  48  49
+				      50  51  52  53  54  55  56  57  58  59
+				      60  61  62  63  64  65  66  67  68  69
+				      70  71  72  73  74  75  76  77  78  79
+				      80  81  82  83  84  85  86  87  88  89
+				      90  91  92  93  94  95  96  97  98  99
+				     100 101 102 103 104 105 106 107 108 109
+				     110 111 112 113 114 115 116 117 118 119
+				     120 121 122 123 124 125 126 127 128 129
+				     130 131 132 133 134 135 136 137 138 139
+				     140 141 142 143 144 145 146 147 148 149
+				     150 151 152 153 154 155 156 157 158 159
+				     160 161 162 163 164 165 166 167 168 169
+				     170 171 172 173 174 175 176 177 178 179
+				     180 181 182 183 184 185 186 187 188 189
+				     190 191 192 193 194 195 196 197 198 199
+				     200 201 202 203 204 205 206 207 208 209
+				     210 211 212 213 214 215 216 217 218 219
+				     220 221 222 223 224 225 226 227 228 229
+				     230 231 232 233 234 235 236 237 238 239
+				     240 241 242 243 244 245 246 247 248 249
+				     250 251 252 253 254 255>;
+		default-brightness-level = <255>;
+		enable-gpios = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		power-supply = <&lvds_ppen>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&ecspi1 {
+	fsl,spi-num-chipselects = <1>;
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash: n25q032 at 0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+		partition at 0 {
+			label = "U-Boot";
+			reg = <0x0 0xC0000>;
+		};
+		partition at C0000 {
+			label = "env";
+			reg = <0xC0000 0x10000>;
+		};
+		partition at D0000 {
+			label = "spare";
+			reg = <0xD0000 0x130000>;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	pmic at 58 {
+		compatible = "dlg,da9063";
+		reg = <0x58>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			vdd_bcore1: bcore1 {
+				regulator-min-microvolt = <1420000>;
+				regulator-max-microvolt = <1420000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vdd_bcore2: bcore2 {
+				regulator-min-microvolt = <1420000>;
+				regulator-max-microvolt = <1420000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vdd_bpro: bpro {
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vdd_bmem: bmem {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vdd_bio: bio {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vdd_bperi: bperi {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vdd_ldo1: ldo1 {
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <1860000>;
+			};
+
+			vdd_ldo2: ldo2 {
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <1860000>;
+			};
+
+			vdd_ldo3: ldo3 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <3440000>;
+			};
+
+			vdd_ldo4: ldo4 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <3440000>;
+			};
+
+			vdd_ldo5: ldo5 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vdd_ldo6: ldo6 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vdd_ldo7: ldo7 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vdd_ldo8: ldo8 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vdd_ldo9: ldo9 {
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vdd_ldo10: ldo10 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vdd_ldo11: ldo11 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	imx6q-ba16 {
+		pinctrl_hog: hoggrp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_4__GPIO1_IO04    0x80000000	/* uSDHC2 CD */
+				MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x80000000	/* uSDHC4 CD */
+				MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x80000000	/* uSDHC4 SDIO PWR */
+				MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x80000000	/* uSDHC4 SDIO WP */
+				MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x80000000	/* uSDHC4 SDIO LED */
+				MX6QDL_PAD_EIM_EB2__GPIO2_IO30   0x80000000	/* SPI1 CS */
+				MX6QDL_PAD_GPIO_17__GPIO7_IO12   0x80000000	/* PCIe Reset */
+				MX6QDL_PAD_GPIO_5__GPIO1_IO05    0x80000000	/* PCIe Wake */
+				MX6QDL_PAD_GPIO_0__CCM_CLKO1     0x130b0	/* FEC CLK */
+				MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x80000000	/* FEC Reset */
+				MX6QDL_PAD_NANDF_D0__GPIO2_IO00  0x80000000	/* GPIO0 */
+				MX6QDL_PAD_NANDF_D1__GPIO2_IO01  0x80000000	/* GPIO1 */
+				MX6QDL_PAD_NANDF_D2__GPIO2_IO02  0x80000000	/* GPIO2 */
+				MX6QDL_PAD_NANDF_D3__GPIO2_IO03  0x80000000	/* GPIO3 */
+				MX6QDL_PAD_NANDF_D4__GPIO2_IO04  0x80000000	/* GPIO4 */
+				MX6QDL_PAD_NANDF_D5__GPIO2_IO05  0x80000000	/* GPIO5 */
+				MX6QDL_PAD_NANDF_D6__GPIO2_IO06  0x80000000	/* GPIO6 */
+				MX6QDL_PAD_NANDF_D7__GPIO2_IO07  0x80000000	/* GPIO7 */
+				MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x80000000	/* CAM_PWDN */
+				MX6QDL_PAD_GPIO_2__GPIO1_IO02    0x80000000	/* CAM_RST */
+				MX6QDL_PAD_GPIO_9__WDOG1_B       0x80000000	/* Watchdog out */
+				MX6QDL_PAD_GPIO_16__GPIO7_IO11   0x80000000	/* HUB_RESET */
+				MX6QDL_PAD_GPIO_18__GPIO7_IO13   0x80000000	/* PMIC Interrupt */
+				MX6QDL_PAD_GPIO_19__GPIO4_IO05   0x80000000	/* AR8033 Interrupt */
+				MX6QDL_PAD_KEY_ROW2__GPIO4_IO11  0x80000000	/* SUS_S3_OUT */
+				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15  0x80000000	/* BLEN_OUT */
+				MX6QDL_PAD_EIM_D22__GPIO3_IO22   0x80000000	/* LVDS_PPEN_OUT */
+				MX6QDL_PAD_KEY_COL2__GPIO4_IO10  0x80000000	/* RTC_INT */
+			>;
+		};
+
+		pinctrl_usdhc4: usdhc4grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_CMD__SD4_CMD    0x17059
+				MX6QDL_PAD_SD4_CLK__SD4_CLK    0x17059
+				MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+				MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+				MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+				MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+				MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
+				MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
+				MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
+				MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
+			>;
+		};
+
+		pinctrl_ecspi1: ecspi1grp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+				MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+				MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+			>;
+		};
+
+		pinctrl_ecspi5: ecspi5rp-1 {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT0__ECSPI5_MISO	0x80000000
+				MX6QDL_PAD_SD1_CMD__ECSPI5_MOSI		0x80000000
+				MX6QDL_PAD_SD1_CLK__ECSPI5_SCLK		0x80000000
+				MX6QDL_PAD_SD1_DAT1__GPIO1_IO17		0x80000000
+			>;
+		};
+
+		pinctrl_pwm1: pwm1grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm2: pwm2grp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_1__PWM2_OUT 0x1b0b1
+			>;
+		};
+
+		pinctrl_usbotg: usbotggrp {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+			>;
+		};
+
+		pinctrl_i2c1: i2c1grp {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+				MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+			>;
+		};
+
+		pinctrl_i2c2: i2c2grp {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+				MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+			>;
+		};
+
+		pinctrl_i2c3: i2c3grp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+				MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+			>;
+		};
+
+		pinctrl_uart3: uart3grp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+				MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+				MX6QDL_PAD_EIM_D23__UART3_CTS_B   0x1b0b1
+				MX6QDL_PAD_EIM_D31__UART3_RTS_B   0x1b0b1
+			>;
+		};
+
+		pinctrl_uart4: uart4grp {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+				MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+			>;
+		};
+
+		pinctrl_usdhc2: usdhc2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD2_CMD__SD2_CMD    0x17059
+				MX6QDL_PAD_SD2_CLK__SD2_CLK    0x10059
+				MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+				MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+				MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+				MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+			>;
+		};
+
+		pinctrl_usdhc3: usdhc3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD3_CMD__SD3_CMD    0x17059
+				MX6QDL_PAD_SD3_CLK__SD3_CLK    0x10059
+				MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+				MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+				MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+				MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+				MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
+				MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
+				MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
+				MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
+			>;
+		};
+
+		pinctrl_usdhc3_reset: usdhc3grp-reset {
+			fsl,pins = <
+				MX6QDL_PAD_SD3_RST__SD3_RESET   0x170F9
+			>;
+		};
+
+		pinctrl_audmux: audmux {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT20__AUD4_TXC  0x130b0
+				MX6QDL_PAD_DISP0_DAT21__AUD4_TXD  0x130b0
+				MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
+				MX6QDL_PAD_DISP0_DAT23__AUD4_RXD  0x130b0
+			>;
+		};
+
+		pinctrl_enet: pinctrl_enet {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_MDIO__ENET_MDIO       0x100b0
+				MX6QDL_PAD_ENET_MDC__ENET_MDC         0x100b0
+				MX6QDL_PAD_RGMII_TXC__RGMII_TXC       0x100b0
+				MX6QDL_PAD_RGMII_TD0__RGMII_TD0       0x100b0
+				MX6QDL_PAD_RGMII_TD1__RGMII_TD1       0x100b0
+				MX6QDL_PAD_RGMII_TD2__RGMII_TD2       0x100b0
+				MX6QDL_PAD_RGMII_TD3__RGMII_TD3       0x100b0
+				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x100b0
+				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK  0x100b0
+				MX6QDL_PAD_RGMII_RXC__RGMII_RXC       0x1b0b0
+				MX6QDL_PAD_RGMII_RD0__RGMII_RD0       0x1b0b0
+				MX6QDL_PAD_RGMII_RD1__RGMII_RD1       0x1b0b0
+				MX6QDL_PAD_RGMII_RD2__RGMII_RD2       0x1b0b0
+				MX6QDL_PAD_RGMII_RD3__RGMII_RD3       0x1b0b0
+				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+			>;
+		};
+	};
+};
+
+&pcie {
+	power-on-gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+	reset-gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&ssi1 {
+	fsl,mode = "i2s-master";
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	fsl,uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	reset-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	enable-sdio-wakeup;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3 &pinctrl_usdhc3_reset>;
+	bus-width = <8>;
+	vmmc-supply = <&vdd_bperi>;
+	vqmmc-supply = <&vdd_bio>;
+	non-removable;
+	keep-power-in-suspend;
+	status = "okay";
+};
Signature · 1 line
2.6.2
#5 lore raw

PATCH v2 3/10 ARM: dts: imx: Add support for Advantech/GE Bx50v3

In reply to Akshay Bhat

From: Justin Waters <[email protected]>

Advantech has 3 carrier boards (B450v3, B650v3, B850v3) which use the Advantech BA-16 module (based on iMX6D). This file has the devicetree entries that are common to all 3 boards.

---
 arch/arm/boot/dts/imx6q-bx50v3.dtsi | 206 ++++++++++++++++++++++++++++++++++++
 1 file changed, 206 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-bx50v3.dtsi
arch/arm/boot/dts/imx6q-bx50v3.dtsi new file +206 -0
new file mode 100644
index 0000000..e9d97ee
@@ -0,0 +1,206 @@
+/*
+ * Copyright 2015 Timesys Corporation.
+ * Copyright 2015 GE Healthcare.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "imx6q-ba16.dtsi"
+
+/ {
+	regulators {
+		/* regulator for wl18xx on sdhc4 */
+		wl18xx_vmmc: regulator at 6 {
+			compatible = "regulator-fixed";
+			regulator-name = "vwl1807";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&pca9539 3 GPIO_ACTIVE_HIGH>;
+			startup-delay-us = <70000>;
+			enable-active-high;
+		};
+
+		reg_wlan: regulator at 7 {
+			compatible = "regulator-fixed";
+			regulator-name = "3P3V_wlan";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio6 14 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx6q-ba16-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx6q-ba16-sgtl5000";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <4>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mclk: clock at 0 {
+			compatible = "fixed-clock";
+			reg = <0>;
+			#clock-cells = <0>;
+			clock-frequency = <22000000>;
+		};
+	};
+};
+
+&i2c1 {
+	pca9547: mux at 70 {
+		compatible = "nxp,pca9547";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mux_i2c3: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			ads7830: ads7830 at 48 {
+				compatible = "ti,ads7830";
+				reg = <0x48>;
+			};
+		};
+
+		mux_i2c4: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+
+			eeprom: eeprom at 50 {
+				compatible = "atmel,24c08";
+				reg = <0x50>;
+			};
+
+			mpl3115: mpl3115 at 60 {
+				compatible = "fsl,mpl3115";
+				reg = <0x60>;
+			};
+		};
+
+		mux_i2c5: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+		};
+
+		mux_i2c6: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			codec: sgtl5000 at 0a {
+				compatible = "fsl,sgtl5000";
+				reg = <0x0a>;
+				clocks = <&mclk>;
+				VDDA-supply = <&reg_1p8v>;
+				VDDIO-supply = <&reg_3p3v>;
+			};
+		};
+
+		mux_i2c7: i2c at 4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+
+			pca9539: pca9539 at 74 {
+				compatible = "nxp,pca9539";
+				reg = <0x74>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				interrupt-parent = <&gpio2>;
+				interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+			};
+		};
+
+		mux_i2c8: i2c at 5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x5>;
+
+			igb at 49 {
+				compatible = "intel,igb";
+				reg = <0x49>;
+			};
+
+			igb at 61 {
+				compatible = "intel,igb";
+				reg = <0x61>;
+			};
+		};
+
+		mux_i2c9: i2c at 6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6>;
+		};
+
+		mux_i2c10: i2c at 7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x7>;
+		};
+	};
+};
+
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <4>;
+	vmmc-supply = <&wl18xx_vmmc>;
+	no-1-8-v;
+	non-removable;
+	enable-sdio-wakeup;
+	keep-power-in-suspend;
+	cap-power-off-card;
+	max-frequency = <25000000>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore at 0 {
+		compatible = "ti,wl1837";
+		reg = <2>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <6 IRQ_TYPE_LEVEL_HIGH>;
+		tcxo-clock-frequency = <26000000>;
+	};
+};
+
+&ecspi5 {
+	fsl,spi-num-chipselects = <1>;
+	cs-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi5>;
+	status = "okay";
+
+	m25_eeprom: m25p80 at 0 {
+		compatible = "atmel,at25";
+		spi-max-frequency = <20000000>;
+		size = <0x8000>;
+		pagesize = <64>;
+		reg = <0>;
+		address-width = <16>;
+	};
+};
Signature · 1 line
2.6.2
#6 lore raw

PATCH v2 4/10 ARM: dts: imx: Add support for Advantech/GE B450v3

In reply to Akshay Bhat

Add support for Advantech/GE B450v3 board.

---
 arch/arm/boot/dts/Makefile         |  1 +
 arch/arm/boot/dts/imx6q-b450v3.dts | 75 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 76 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-b450v3.dts
arch/arm/boot/dts/Makefile +1 -0
index 30bbc37..b3330fe 100644
@@ -310,6 +310,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-wandboard-revb1.dtb \
 	imx6q-apf6dev.dtb \
 	imx6q-arm2.dtb \
+	imx6q-b450v3.dtb \
 	imx6q-cm-fx6.dtb \
 	imx6q-cubox-i.dtb \
 	imx6q-dfi-fs700-m60.dtb \
arch/arm/boot/dts/imx6q-b450v3.dts new file +75 -0

75 lines not on this page · raw message

Signature · 1 line
2.6.2
#7 lore raw

PATCH v2 5/10 ARM: dts: imx: Add support for Advantech/GE B650v3

In reply to Akshay Bhat

Add support for Advantech/GE B650v3 board.

---
 arch/arm/boot/dts/Makefile         |  1 +
 arch/arm/boot/dts/imx6q-b650v3.dts | 74 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 75 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-b650v3.dts
arch/arm/boot/dts/Makefile +1 -0
index b3330fe..e2df9f8 100644
@@ -311,6 +311,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-apf6dev.dtb \
 	imx6q-arm2.dtb \
 	imx6q-b450v3.dtb \
+	imx6q-b650v3.dtb \
 	imx6q-cm-fx6.dtb \
 	imx6q-cubox-i.dtb \
 	imx6q-dfi-fs700-m60.dtb \
arch/arm/boot/dts/imx6q-b650v3.dts new file +74 -0

74 lines not on this page · raw message

Signature · 1 line
2.6.2
#8 lore raw

PATCH v2 6/10 ARM: dts: imx: Add support for Advantech/GE B850v3

In reply to Akshay Bhat

Add support for Advantech/GE B850v3 board.

---
 arch/arm/boot/dts/Makefile         |   1 +
 arch/arm/boot/dts/imx6q-b850v3.dts | 122 +++++++++++++++++++++++++++++++++++++
 2 files changed, 123 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-b850v3.dts
arch/arm/boot/dts/Makefile +1 -0
index e2df9f8..7ad1eb8 100644
@@ -312,6 +312,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-arm2.dtb \
 	imx6q-b450v3.dtb \
 	imx6q-b650v3.dtb \
+	imx6q-b850v3.dtb \
 	imx6q-cm-fx6.dtb \
 	imx6q-cubox-i.dtb \
 	imx6q-dfi-fs700-m60.dtb \
arch/arm/boot/dts/imx6q-b850v3.dts new file +122 -0

122 lines not on this page · raw message

Signature · 1 line
2.6.2
#9 lore raw

PATCH v2 7/10 of: Add vendor prefix for General Electric Company

In reply to Akshay Bhat

This patch adds vendor prefix for General Electric Company

---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/vendor-prefixes.txt +1 -0
index 2b3c5ac..71dcbd5 100644
@@ -87,6 +87,7 @@ fcs	Fairchild Semiconductor
 firefly	Firefly
 focaltech	FocalTech Systems Co.,Ltd
 fsl	Freescale Semiconductor
+ge	General Electric Company
 GEFanuc	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
 gef	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
 geniatech	Geniatech, Inc.
Signature · 1 line
2.6.2
maintainer
#10 lore raw

PATCH v2 7/10 of: Add vendor prefix for General Electric Company

Quoted 12 lines · Akshay Bhat

This patch adds vendor prefix for General Electric Company

---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/vendor-prefixes.txt +0 -0
index 2b3c5ac..71dcbd5 100644

Documentation/devicetree/bindings/vendor-prefixes.txt fcs Fairchild Semiconductor · line 90

Quoted 4 lines
Documentation/devicetree/bindings/vendor-prefixes.txt +1 -0
@@ -87,6 +87,7 @@ fcs	Fairchild Semiconductor
 firefly	Firefly
 focaltech	FocalTech Systems Co.,Ltd
 fsl	Freescale Semiconductor
+ge	General Electric Company

This is short too, but it is well known and the stock ticker so:

Quoted 6 lines
Documentation/devicetree/bindings/vendor-prefixes.txt +0 -0
 GEFanuc	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
 gef	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
 geniatech	Geniatech, Inc.
Signature · 1 line
2.6.2
#11 lore raw

PATCH v2 7/10 of: Add vendor prefix for General Electric Company

In reply to Akshay Bhat

Am Donnerstag, den 05.11.2015, 13:13 -0500 schrieb Akshay Bhat:

Quoted 3 lines

This patch adds vendor prefix for General Electric Company

This patch should move to the beginning of the series.

Quoted 16 lines
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/vendor-prefixes.txt +1 -0
index 2b3c5ac..71dcbd5 100644
@@ -87,6 +87,7 @@ fcs	Fairchild Semiconductor
 firefly	Firefly
 focaltech	FocalTech Systems Co.,Ltd
 fsl	Freescale Semiconductor
+ge	General Electric Company
 GEFanuc	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
 gef	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
 geniatech	Geniatech, Inc.
Signature · 2 lines
Pengutronix e.K.             | Lucas Stach                 |
Industrial Linux Solutions   | http://www.pengutronix.de/  |
#12 lore raw

PATCH v2 8/10 ARM: dts: imx: Update vendor info for GE Bx50v3 boards

In reply to Akshay Bhat

Update vendor and copyright info for GE Bx50v3 boards

---
 arch/arm/boot/dts/imx6q-b450v3.dts | 4 ++--
 arch/arm/boot/dts/imx6q-b650v3.dts | 4 ++--
 arch/arm/boot/dts/imx6q-b850v3.dts | 4 ++--
 3 files changed, 6 insertions(+), 6 deletions(-)
arch/arm/boot/dts/imx6q-b450v3.dts +2 -2
index d63d9e1..efe9c1e 100644
@@ -1,6 +1,6 @@
 /*
  * Copyright 2015 Timesys Corporation.
- * Copyright 2015 GE Healthcare.
+ * Copyright 2015 General Electric Company
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License
@@ -16,7 +16,7 @@
 
 / {
 	model = "Advantech MX6Q B450V3 QSeven Board";
-	compatible = "adv,imx6q-b450v3", "adv,imx6q-ba16", "fsl,imx6q";
+	compatible = "ge,imx6q-b450v3", "adv,imx6q-ba16", "fsl,imx6q";
 
 	chosen {
 		stdout-path = &uart3;
arch/arm/boot/dts/imx6q-b650v3.dts +2 -2
index 29cbdb0..d40efa9 100644
@@ -1,6 +1,6 @@
 /*
  * Copyright 2015 Timesys Corporation.
- * Copyright 2015 GE Healthcare.
+ * Copyright 2015 General Electric Company
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License
@@ -16,7 +16,7 @@
 
 / {
 	model = "Advantech MX6Q B650V3 QSeven Board";
-	compatible = "adv,imx6q-b650v3", "adv,imx6q-ba16", "fsl,imx6q";
+	compatible = "ge,imx6q-b650v3", "adv,imx6q-ba16", "fsl,imx6q";
 
 	chosen {
 		stdout-path = &uart3;
arch/arm/boot/dts/imx6q-b850v3.dts +2 -2
index be6c0da..a77f392 100644
@@ -1,6 +1,6 @@
 /*
  * Copyright 2015 Timesys Corporation.
- * Copyright 2015 GE Healthcare.
+ * Copyright 2015 General Electric Company
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License
@@ -16,7 +16,7 @@
 
 / {
 	model = "Advantech MX6Q B850V3 QSeven Board";
-	compatible = "adv,imx6q-b850v3", "adv,imx6q-ba16", "fsl,imx6q";
+	compatible = "ge,imx6q-b850v3", "adv,imx6q-ba16", "fsl,imx6q";
 
 	chosen {
 		stdout-path = &uart3;
Signature · 1 line
2.6.2
#13 lore raw

PATCH v2 8/10 ARM: dts: imx: Update vendor info for GE Bx50v3 boards

Am Donnerstag, den 05.11.2015, 13:13 -0500 schrieb Akshay Bhat:

Quoted 3 lines

Update vendor and copyright info for GE Bx50v3 boards

This one and the following patches should be folded into the patches introducing the files being patched here. They fix the original patches and it makes no sense to merge patches with slightly wrong DTs, just to immediately following up with patches to fix things.

Regards,
Lucas

Quoted 69 lines
---
 arch/arm/boot/dts/imx6q-b450v3.dts | 4 ++--
 arch/arm/boot/dts/imx6q-b650v3.dts | 4 ++--
 arch/arm/boot/dts/imx6q-b850v3.dts | 4 ++--
 3 files changed, 6 insertions(+), 6 deletions(-)
arch/arm/boot/dts/imx6q-b450v3.dts +2 -2
index d63d9e1..efe9c1e 100644
@@ -1,6 +1,6 @@
 /*
  * Copyright 2015 Timesys Corporation.
- * Copyright 2015 GE Healthcare.
+ * Copyright 2015 General Electric Company
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License
@@ -16,7 +16,7 @@
 
 / {
 	model = "Advantech MX6Q B450V3 QSeven Board";
-	compatible = "adv,imx6q-b450v3", "adv,imx6q-ba16", "fsl,imx6q";
+	compatible = "ge,imx6q-b450v3", "adv,imx6q-ba16", "fsl,imx6q";
 
 	chosen {
 		stdout-path = &uart3;
arch/arm/boot/dts/imx6q-b650v3.dts +2 -2
index 29cbdb0..d40efa9 100644
@@ -1,6 +1,6 @@
 /*
  * Copyright 2015 Timesys Corporation.
- * Copyright 2015 GE Healthcare.
+ * Copyright 2015 General Electric Company
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License
@@ -16,7 +16,7 @@
 
 / {
 	model = "Advantech MX6Q B650V3 QSeven Board";
-	compatible = "adv,imx6q-b650v3", "adv,imx6q-ba16", "fsl,imx6q";
+	compatible = "ge,imx6q-b650v3", "adv,imx6q-ba16", "fsl,imx6q";
 
 	chosen {
 		stdout-path = &uart3;
arch/arm/boot/dts/imx6q-b850v3.dts +2 -2
index be6c0da..a77f392 100644
@@ -1,6 +1,6 @@
 /*
  * Copyright 2015 Timesys Corporation.
- * Copyright 2015 GE Healthcare.
+ * Copyright 2015 General Electric Company
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License
@@ -16,7 +16,7 @@
 
 / {
 	model = "Advantech MX6Q B850V3 QSeven Board";
-	compatible = "adv,imx6q-b850v3", "adv,imx6q-ba16", "fsl,imx6q";
+	compatible = "ge,imx6q-b850v3", "adv,imx6q-ba16", "fsl,imx6q";
 
 	chosen {
 		stdout-path = &uart3;
Signature · 2 lines
Pengutronix e.K.             | Lucas Stach                 |
Industrial Linux Solutions   | http://www.pengutronix.de/  |
#14 lore raw

PATCH v2 8/10 ARM: dts: imx: Update vendor info for GE Bx50v3 boards

Quoted 5 lines · Lucas Stach

Am Donnerstag, den 05.11.2015, 13:13 -0500 schrieb Akshay Bhat:

Quoted 3 lines

Update vendor and copyright info for GE Bx50v3 boards

Quoted 8 lines

This one and the following patches should be folded into the patches introducing the files being patched here. They fix the original patches and it makes no sense to merge patches with slightly wrong DTs, just to immediately following up with patches to fix things.

Regards,
Lucas

Fixed in v3.

http://lists.infradead.org/pipermail/linux-arm-kernel/2015-November/384202.html

#15 lore raw

PATCH v2 9/10 ARM: dts: imx: Add mma8453 support

In reply to Akshay Bhat
---
 arch/arm/boot/dts/imx6q-bx50v3.dtsi | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)
arch/arm/boot/dts/imx6q-bx50v3.dtsi +6 -1
index e9d97ee..2715cd9 100644
@@ -1,6 +1,6 @@
 /*
  * Copyright 2015 Timesys Corporation.
- * Copyright 2015 GE Healthcare.
+ * Copyright 2015 General Electric Company
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License
@@ -79,6 +79,11 @@
 				compatible = "ti,ads7830";
 				reg = <0x48>;
 			};
+
+			mma8453: mma8453 at 1c {
+				compatible = "fsl,mma8453";
+				reg = <0x1c>;
+			};
 		};
 
 		mux_i2c4: i2c at 1 {
Signature · 1 line
2.6.2
#16 lore raw

PATCH v2 10/10 ARM: dts: imx6q-ba16: Cleanup pinctrl and LDO

In reply to Akshay Bhat

Incorporate feedback from Lucas Stash
- Move entries from pinctrl_hog to relevant groups
- Remove unused PCIe power-on-gpio entry
- Remove always-on from regulators that do not need to be always-on

---
 arch/arm/boot/dts/imx6q-ba16.dtsi | 85 +++++++++++++++++++++++++--------------
 1 file changed, 55 insertions(+), 30 deletions(-)
arch/arm/boot/dts/imx6q-ba16.dtsi +55 -30
index 3d47039..d0c4568 100644
@@ -2,7 +2,7 @@
  * Support for imx6 based Advantech DMS-BA16 Qseven module
  *
  * Copyright 2015 Timesys Corporation.
- * Copyright 2015 GE Healthcare.
+ * Copyright 2015 General Electric Company
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License
@@ -73,6 +73,8 @@
 	};
 
 	backlight {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_display>;
 		compatible = "pwm-backlight";
 		pwms = <&pwm1 0 5000000>;
 		brightness-levels = <  0   1   2   3   4   5   6   7   8   9
@@ -176,6 +178,8 @@
 	pmic@58 {
 		compatible = "dlg,da9063";
 		reg = <0x58>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio7>;
 		interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
 
@@ -245,43 +249,31 @@
 			vdd_ldo5: ldo5 {
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <3600000>;
-				regulator-always-on;
-				regulator-boot-on;
 			};
 
 			vdd_ldo6: ldo6 {
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <3600000>;
-				regulator-always-on;
-				regulator-boot-on;
 			};
 
 			vdd_ldo7: ldo7 {
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <3600000>;
-				regulator-always-on;
-				regulator-boot-on;
 			};
 
 			vdd_ldo8: ldo8 {
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <3600000>;
-				regulator-always-on;
-				regulator-boot-on;
 			};
 
 			vdd_ldo9: ldo9 {
 				regulator-min-microvolt = <950000>;
 				regulator-max-microvolt = <3600000>;
-				regulator-always-on;
-				regulator-boot-on;
 			};
 
 			vdd_ldo10: ldo10 {
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <3600000>;
-				regulator-always-on;
-				regulator-boot-on;
 			};
 
 			vdd_ldo11: ldo11 {
@@ -301,16 +293,6 @@
 	imx6q-ba16 {
 		pinctrl_hog: hoggrp {
 			fsl,pins = <
-				MX6QDL_PAD_GPIO_4__GPIO1_IO04    0x80000000	/* uSDHC2 CD */
-				MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x80000000	/* uSDHC4 CD */
-				MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x80000000	/* uSDHC4 SDIO PWR */
-				MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x80000000	/* uSDHC4 SDIO WP */
-				MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x80000000	/* uSDHC4 SDIO LED */
-				MX6QDL_PAD_EIM_EB2__GPIO2_IO30   0x80000000	/* SPI1 CS */
-				MX6QDL_PAD_GPIO_17__GPIO7_IO12   0x80000000	/* PCIe Reset */
-				MX6QDL_PAD_GPIO_5__GPIO1_IO05    0x80000000	/* PCIe Wake */
-				MX6QDL_PAD_GPIO_0__CCM_CLKO1     0x130b0	/* FEC CLK */
-				MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x80000000	/* FEC Reset */
 				MX6QDL_PAD_NANDF_D0__GPIO2_IO00  0x80000000	/* GPIO0 */
 				MX6QDL_PAD_NANDF_D1__GPIO2_IO01  0x80000000	/* GPIO1 */
 				MX6QDL_PAD_NANDF_D2__GPIO2_IO02  0x80000000	/* GPIO2 */
@@ -321,17 +303,44 @@
 				MX6QDL_PAD_NANDF_D7__GPIO2_IO07  0x80000000	/* GPIO7 */
 				MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x80000000	/* CAM_PWDN */
 				MX6QDL_PAD_GPIO_2__GPIO1_IO02    0x80000000	/* CAM_RST */
-				MX6QDL_PAD_GPIO_9__WDOG1_B       0x80000000	/* Watchdog out */
-				MX6QDL_PAD_GPIO_16__GPIO7_IO11   0x80000000	/* HUB_RESET */
-				MX6QDL_PAD_GPIO_18__GPIO7_IO13   0x80000000	/* PMIC Interrupt */
-				MX6QDL_PAD_GPIO_19__GPIO4_IO05   0x80000000	/* AR8033 Interrupt */
+				MX6QDL_PAD_GPIO_0__CCM_CLKO1     0x130b0	/* CAM CLK */
 				MX6QDL_PAD_KEY_ROW2__GPIO4_IO11  0x80000000	/* SUS_S3_OUT */
-				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15  0x80000000	/* BLEN_OUT */
-				MX6QDL_PAD_EIM_D22__GPIO3_IO22   0x80000000	/* LVDS_PPEN_OUT */
 				MX6QDL_PAD_KEY_COL2__GPIO4_IO10  0x80000000	/* RTC_INT */
 			>;
 		};
 
+		pinctrl_wdog: wdoggrp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_9__WDOG1_B       0x80000000	/* Watchdog out */
+			>;
+		};
+
+		pinctrl_pmic: pmicgrp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_18__GPIO7_IO13   0x80000000	/* PMIC Interrupt */
+			>;
+		};
+
+		pinctrl_usbhub: usbhubgrp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_16__GPIO7_IO11   0x80000000	/* HUB_RESET */
+			>;
+		};
+
+		pinctrl_pcie: pciegrp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_17__GPIO7_IO12   0x80000000	/* PCIe Reset */
+				MX6QDL_PAD_GPIO_5__GPIO1_IO05    0x80000000	/* PCIe Wake */
+			>;
+		};
+
+		pinctrl_display: dispgrp {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15  0x80000000 /* BLEN_OUT */
+				MX6QDL_PAD_EIM_D22__GPIO3_IO22   0x80000000 /* LVDS_PPEN_OUT */
+			>;
+		};
+
 		pinctrl_usdhc4: usdhc4grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD4_CMD__SD4_CMD    0x17059
@@ -344,6 +353,10 @@
 				MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
 				MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
 				MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
+				MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x80000000 /* uSDHC4 CD */
+				MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x80000000 /* uSDHC4 SDIO PWR */
+				MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x80000000 /* uSDHC4 SDIO WP */
+				MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x80000000 /* uSDHC4 SDIO LED */
 			>;
 		};
 
@@ -352,6 +365,7 @@
 				MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
 				MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
 				MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+				MX6QDL_PAD_EIM_EB2__GPIO2_IO30	0x80000000 /* SPI1 CS */
 			>;
 		};
 
@@ -427,6 +441,7 @@
 				MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
 				MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
 				MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+				MX6QDL_PAD_GPIO_4__GPIO1_IO04  0x80000000 /* uSDHC2 CD */
 			>;
 		};
 
@@ -477,13 +492,16 @@
 				MX6QDL_PAD_RGMII_RD2__RGMII_RD2       0x1b0b0
 				MX6QDL_PAD_RGMII_RD3__RGMII_RD3       0x1b0b0
 				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+				MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28     0x80000000 /* FEC Reset */
+				MX6QDL_PAD_GPIO_19__GPIO4_IO05        0x80000000 /* AR8033 Interrupt */
 			>;
 		};
 	};
 };
 
 &pcie {
-	power-on-gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
 	reset-gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
@@ -524,6 +542,8 @@
 };
 
 &usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbhub>;
 	vbus-supply = <&reg_usb_h1_vbus>;
 	reset-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
 	status = "okay";
@@ -557,3 +577,8 @@
 	keep-power-in-suspend;
 	status = "okay";
 };
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+};
Signature · 1 line
2.6.2