Skip to contentSkip to conversation

i40e: Remove CONFIG_I40E_VXLAN

PATCH Superseded Anjali Singhai Jain 4 participants 16 messages Nov 10, 2015 – Nov 11, 2015

Subsystems (9)

v4 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

PATCH v4 1/6 i40e: Remove CONFIG_I40E_VXLAN

If the kernel flag CONFIG_VXLAN is true or CONFIG_VXLAN_MODULE is true, enable VXLAN offload in the driver.

v2: Fix bisection error for this patch series.

---
 drivers/net/ethernet/intel/i40e/i40e.h      |  2 --
 drivers/net/ethernet/intel/i40e/i40e_main.c | 10 ++--------
 2 files changed, 2 insertions(+), 10 deletions(-)
drivers/net/ethernet/intel/i40e/i40e.h +0 -2
index 8ed759e..6c4d154 100644
@@ -282,11 +282,9 @@ struct i40e_pf {
 	u32 fd_atr_cnt;
 	u32 fd_tcp_rule;
 
-#if IS_ENABLED(CONFIG_VXLAN)
 	__be16  vxlan_ports[I40E_MAX_PF_UDP_OFFLOAD_PORTS];
 	u16 pending_vxlan_bitmap;
 
-#endif
 	enum i40e_interrupt_policy int_policy;
 	u16 rx_itr_default;
 	u16 tx_itr_default;
drivers/net/ethernet/intel/i40e/i40e_main.c +2 -8
index b447af6..0235a8a 100644
@@ -6990,13 +6990,13 @@ static void i40e_handle_mdd_event(struct i40e_pf *pf)
 	i40e_flush(hw);
 }
 
-#if IS_ENABLED(CONFIG_VXLAN)
 /**
  * i40e_sync_vxlan_filters_subtask - Sync the VSI filter list with HW
  * @pf: board private structure
  **/
 static void i40e_sync_vxlan_filters_subtask(struct i40e_pf *pf)
 {
+#if IS_ENABLED(CONFIG_VXLAN)
 	struct i40e_hw *hw = &pf->hw;
 	i40e_status ret;
 	__be16 port;
@@ -7030,9 +7030,9 @@ static void i40e_sync_vxlan_filters_subtask(struct i40e_pf *pf)
 			}
 		}
 	}
+#endif
 }
 
-#endif
 /**
  * i40e_service_task - Run the driver's async subtasks
  * @work: pointer to work_struct containing our data
@@ -7057,9 +7057,7 @@ static void i40e_service_task(struct work_struct *work)
 	i40e_watchdog_subtask(pf);
 	i40e_fdir_reinit_subtask(pf);
 	i40e_sync_filters_subtask(pf);
-#if IS_ENABLED(CONFIG_VXLAN)
 	i40e_sync_vxlan_filters_subtask(pf);
-#endif
 	i40e_clean_adminq_subtask(pf);
 
 	i40e_service_event_complete(pf);
@@ -8433,7 +8431,6 @@ static int i40e_set_features(struct net_device *netdev,
 	return 0;
 }
 
-#if IS_ENABLED(CONFIG_VXLAN)
 /**
  * i40e_get_vxlan_port_idx - Lookup a possibly offloaded for Rx UDP port
  * @pf: board private structure
@@ -8528,7 +8525,6 @@ static void i40e_del_vxlan_port(struct net_device *netdev,
 	}
 }
 
-#endif
 static int i40e_get_phys_port_id(struct net_device *netdev,
 				 struct netdev_phys_item_id *ppid)
 {
@@ -8753,10 +8749,8 @@ static const struct net_device_ops i40e_netdev_ops = {
 	.ndo_get_vf_config	= i40e_ndo_get_vf_config,
 	.ndo_set_vf_link_state	= i40e_ndo_set_vf_link_state,
 	.ndo_set_vf_spoofchk	= i40e_ndo_set_vf_spoofchk,
-#if IS_ENABLED(CONFIG_VXLAN)
 	.ndo_add_vxlan_port	= i40e_add_vxlan_port,
 	.ndo_del_vxlan_port	= i40e_del_vxlan_port,
-#endif
 	.ndo_get_phys_port_id	= i40e_get_phys_port_id,
 	.ndo_fdb_add		= i40e_ndo_fdb_add,
 	.ndo_features_check	= i40e_features_check,
Signature · 1 line
1.8.1.4
#1 lore raw

PATCH v4 2/6 net: Generalize udp based tunnel offload

Replace add/del ndo ops for vxlan_port with tunnel_port so that all UDP based tunnels can use the same ndo op. Add a parameter to pass tunnel type to the ndo_op.

Change all drivers to use the generalized udp tunnel offload

Patch was compile tested with x86_64_defconfig.

---
 drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c | 15 ++++++---
 drivers/net/ethernet/broadcom/bnxt/bnxt.c        | 15 ++++++---
 drivers/net/ethernet/emulex/benet/be_main.c      | 15 ++++++---
 drivers/net/ethernet/intel/fm10k/fm10k_netdev.c  | 27 ++++++++++++----
 drivers/net/ethernet/intel/i40e/i40e_main.c      | 41 +++++++++++++++++-------
 drivers/net/ethernet/intel/ixgbe/ixgbe_main.c    | 17 +++++++---
 drivers/net/ethernet/mellanox/mlx4/en_netdev.c   | 21 ++++++++----
 drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c | 17 +++++++---
 drivers/net/vxlan.c                              | 20 ++++++------
 include/linux/netdevice.h                        | 39 ++++++++++++----------
 include/net/udp_tunnel.h                         |  5 +++
 11 files changed, 161 insertions(+), 71 deletions(-)
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c +11 -4
index f1d62d5..3a863dc 100644
@@ -47,6 +47,7 @@
 #include <net/ip.h>
 #include <net/ipv6.h>
 #include <net/tcp.h>
+#include <net/udp_tunnel.h>
 #include <net/vxlan.h>
 #include <net/checksum.h>
 #include <net/ip6_checksum.h>
@@ -10124,11 +10125,14 @@ static void __bnx2x_add_vxlan_port(struct bnx2x *bp, u16 port)
 }
 
 static void bnx2x_add_vxlan_port(struct net_device *netdev,
-				 sa_family_t sa_family, __be16 port)
+				 sa_family_t sa_family, __be16 port,
+				 u32 type)
 {
 	struct bnx2x *bp = netdev_priv(netdev);
 	u16 t_port = ntohs(port);
 
+	if (type != UDP_TUNNEL_VXLAN)
+		return;
 	__bnx2x_add_vxlan_port(bp, t_port);
 }
 
@@ -10152,11 +10156,14 @@ static void __bnx2x_del_vxlan_port(struct bnx2x *bp, u16 port)
 }
 
 static void bnx2x_del_vxlan_port(struct net_device *netdev,
-				 sa_family_t sa_family, __be16 port)
+				 sa_family_t sa_family, __be16 port,
+				 u32 type)
 {
 	struct bnx2x *bp = netdev_priv(netdev);
 	u16 t_port = ntohs(port);
 
+	if (type != UDP_TUNNEL_VXLAN)
+		return;
 	__bnx2x_del_vxlan_port(bp, t_port);
 }
 #endif
@@ -13011,8 +13018,8 @@ static const struct net_device_ops bnx2x_netdev_ops = {
 	.ndo_set_vf_link_state	= bnx2x_set_vf_link_state,
 	.ndo_features_check	= bnx2x_features_check,
 #ifdef CONFIG_BNX2X_VXLAN
-	.ndo_add_vxlan_port	= bnx2x_add_vxlan_port,
-	.ndo_del_vxlan_port	= bnx2x_del_vxlan_port,
+	.ndo_add_udp_tunnel_port	= bnx2x_add_vxlan_port,
+	.ndo_del_udp_tunnel_port	= bnx2x_del_vxlan_port,
 #endif
 };
 
drivers/net/ethernet/broadcom/bnxt/bnxt.c +11 -4
index 6c2e0c6..af68428 100644
@@ -39,6 +39,7 @@
 #include <net/ip6_checksum.h>
 #if defined(CONFIG_VXLAN) || defined(CONFIG_VXLAN_MODULE)
 #include <net/vxlan.h>
+#include <net/udp_tunnel.h>
 #endif
 #ifdef CONFIG_NET_RX_BUSY_POLL
 #include <net/busy_poll.h>
@@ -5409,7 +5410,7 @@ static void bnxt_cfg_ntp_filters(struct bnxt *bp)
 #endif /* CONFIG_RFS_ACCEL */
 
 static void bnxt_add_vxlan_port(struct net_device *dev, sa_family_t sa_family,
-				__be16 port)
+				__be16 port, u32 type)
 {
 	struct bnxt *bp = netdev_priv(dev);
 
@@ -5419,6 +5420,9 @@ static void bnxt_add_vxlan_port(struct net_device *dev, sa_family_t sa_family,
 	if (sa_family != AF_INET6 && sa_family != AF_INET)
 		return;
 
+	if (type != UDP_TUNNEL_VXLAN)
+		return;
+
 	if (bp->vxlan_port_cnt && bp->vxlan_port != port)
 		return;
 
@@ -5431,7 +5435,7 @@ static void bnxt_add_vxlan_port(struct net_device *dev, sa_family_t sa_family,
 }
 
 static void bnxt_del_vxlan_port(struct net_device *dev, sa_family_t sa_family,
-				__be16 port)
+				__be16 port, u32 type)
 {
 	struct bnxt *bp = netdev_priv(dev);
 
@@ -5441,6 +5445,9 @@ static void bnxt_del_vxlan_port(struct net_device *dev, sa_family_t sa_family,
 	if (sa_family != AF_INET6 && sa_family != AF_INET)
 		return;
 
+	if (type != UDP_TUNNEL_VXLAN)
+		return;
+
 	if (bp->vxlan_port_cnt && bp->vxlan_port == port) {
 		bp->vxlan_port_cnt--;
 
@@ -5479,8 +5486,8 @@ static const struct net_device_ops bnxt_netdev_ops = {
 #ifdef CONFIG_RFS_ACCEL
 	.ndo_rx_flow_steer	= bnxt_rx_flow_steer,
 #endif
-	.ndo_add_vxlan_port	= bnxt_add_vxlan_port,
-	.ndo_del_vxlan_port	= bnxt_del_vxlan_port,
+	.ndo_add_udp_tunnel_port	= bnxt_add_vxlan_port,
+	.ndo_del_udp_tunnel_port	= bnxt_del_vxlan_port,
 #ifdef CONFIG_NET_RX_BUSY_POLL
 	.ndo_busy_poll		= bnxt_busy_poll,
 #endif
drivers/net/ethernet/emulex/benet/be_main.c +11 -4
index eb48a97..6af9f27 100644
@@ -23,6 +23,7 @@
 #include <linux/aer.h>
 #include <linux/if_bridge.h>
 #include <net/busy_poll.h>
+#include <net/udp_tunnel.h>
 #include <net/vxlan.h>
 
 MODULE_VERSION(DRV_VER);
@@ -5177,12 +5178,15 @@ static int be_ndo_bridge_getlink(struct sk_buff *skb, u32 pid, u32 seq,
  * until after all the tunnels are removed.
  */
 static void be_add_vxlan_port(struct net_device *netdev, sa_family_t sa_family,
-			      __be16 port)
+			      __be16 port, u32 type)
 {
 	struct be_adapter *adapter = netdev_priv(netdev);
 	struct device *dev = &adapter->pdev->dev;
 	int status;
 
+	if (type != UDP_TUNNEL_VXLAN)
+		return;
+
 	if (lancer_chip(adapter) || BEx_chip(adapter) || be_is_mc(adapter))
 		return;
 
@@ -5231,10 +5235,13 @@ err:
 }
 
 static void be_del_vxlan_port(struct net_device *netdev, sa_family_t sa_family,
-			      __be16 port)
+			      __be16 port, u32 type)
 {
 	struct be_adapter *adapter = netdev_priv(netdev);
 
+	if (type != UDP_TUNNEL_VXLAN)
+		return;
+
 	if (lancer_chip(adapter) || BEx_chip(adapter) || be_is_mc(adapter))
 		return;
 
@@ -5344,8 +5351,8 @@ static const struct net_device_ops be_netdev_ops = {
 	.ndo_busy_poll		= be_busy_poll,
 #endif
 #ifdef CONFIG_BE2NET_VXLAN
-	.ndo_add_vxlan_port	= be_add_vxlan_port,
-	.ndo_del_vxlan_port	= be_del_vxlan_port,
+	.ndo_add_udp_tunnel_port	= be_add_vxlan_port,
+	.ndo_del_udp_tunnel_port	= be_del_vxlan_port,
 	.ndo_features_check	= be_features_check,
 #endif
 	.ndo_get_phys_port_id   = be_get_phys_port_id,
drivers/net/ethernet/intel/fm10k/fm10k_netdev.c +21 -6
index 722ac52..bf7af95 100644
@@ -21,6 +21,7 @@
 #include "fm10k.h"
 #include <linux/vmalloc.h>
 #if IS_ENABLED(CONFIG_FM10K_VXLAN)
+#include <net/udp_tunnel.h>
 #include <net/vxlan.h>
 #endif /* CONFIG_FM10K_VXLAN */
 
@@ -439,18 +440,24 @@ static void fm10k_restore_vxlan_port(struct fm10k_intfc *interface)
  * @netdev: network interface device structure
  * @sa_family: Address family of new port
  * @port: port number used for VXLAN
+ * @type: Tunnel type
  *
- * This funciton is called when a new VXLAN interface has added a new port
+ * This function is called when a new VXLAN interface has added a new port
  * number to the range that is currently in use for VXLAN.  The new port
  * number is always added to the tail so that the port number list should
  * match the order in which the ports were allocated.  The head of the list
  * is always used as the VXLAN port number for offloads.
  **/
 static void fm10k_add_vxlan_port(struct net_device *dev,
-				 sa_family_t sa_family, __be16 port) {
+				 sa_family_t sa_family, __be16 port,
+				 u32 type) {
+#if IS_ENABLED(CONFIG_FM10K_VXLAN)
 	struct fm10k_intfc *interface = netdev_priv(dev);
 	struct fm10k_vxlan_port *vxlan_port;
 
+	if (type != UDP_TUNNEL_VXLAN)
+		return;
+
 	/* only the PF supports configuring tunnels */
 	if (interface->hw.mac.type != fm10k_mac_pf)
 		return;
@@ -476,6 +483,7 @@ insert_tail:
 	list_add_tail(&vxlan_port->list, &interface->vxlan_port);
 
 	fm10k_restore_vxlan_port(interface);
+#endif
 }
 
 /**
@@ -483,17 +491,23 @@ insert_tail:
  * @netdev: network interface device structure
  * @sa_family: Address family of freed port
  * @port: port number used for VXLAN
+ * @type: Tunnel type
  *
- * This funciton is called when a new VXLAN interface has freed a port
+ * This function is called when a new VXLAN interface has freed a port
  * number from the range that is currently in use for VXLAN.  The freed
  * port is removed from the list and the new head is used to determine
  * the port number for offloads.
  **/
 static void fm10k_del_vxlan_port(struct net_device *dev,
-				 sa_family_t sa_family, __be16 port) {
+				 sa_family_t sa_family, __be16 port,
+				 u32 type) {
+#if IS_ENABLED(CONFIG_FM10K_VXLAN)
 	struct fm10k_intfc *interface = netdev_priv(dev);
 	struct fm10k_vxlan_port *vxlan_port;
 
+	if (type != UDP_TUNNEL_VXLAN)
+		return;
+
 	if (interface->hw.mac.type != fm10k_mac_pf)
 		return;
 
@@ -508,6 +522,7 @@ static void fm10k_del_vxlan_port(struct net_device *dev,
 	}
 
 	fm10k_restore_vxlan_port(interface);
+#endif
 }
 
 /**
@@ -1389,8 +1404,8 @@ static const struct net_device_ops fm10k_netdev_ops = {
 	.ndo_set_vf_vlan	= fm10k_ndo_set_vf_vlan,
 	.ndo_set_vf_rate	= fm10k_ndo_set_vf_bw,
 	.ndo_get_vf_config	= fm10k_ndo_get_vf_config,
-	.ndo_add_vxlan_port	= fm10k_add_vxlan_port,
-	.ndo_del_vxlan_port	= fm10k_del_vxlan_port,
+	.ndo_add_udp_tunnel_port	= fm10k_add_vxlan_port,
+	.ndo_del_udp_tunnel_port	= fm10k_del_vxlan_port,
 	.ndo_do_ioctl		= fm10k_ioctl,
 	.ndo_dfwd_add_station	= fm10k_dfwd_add_station,
 	.ndo_dfwd_del_station	= fm10k_dfwd_del_station,
drivers/net/ethernet/intel/i40e/i40e_main.c +29 -12

99 lines not on this page · raw message

drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +13 -4
index f5730dd..d7ad9d9 100644
@@ -50,6 +50,7 @@
 #include <linux/if_bridge.h>
 #include <linux/prefetch.h>
 #include <scsi/fc/fc_fcoe.h>
+#include <net/udp_tunnel.h>
 #include <net/vxlan.h>
 
 #ifdef CONFIG_OF
@@ -8312,14 +8313,18 @@ static int ixgbe_set_features(struct net_device *netdev,
  * @dev: The port's netdev
  * @sa_family: Socket Family that VXLAN is notifiying us about
  * @port: New UDP port number that VXLAN started listening to
+ * @type: Tunnel type
  **/
 static void ixgbe_add_vxlan_port(struct net_device *dev, sa_family_t sa_family,
-				 __be16 port)
+				 __be16 port, u32 type)
 {
 	struct ixgbe_adapter *adapter = netdev_priv(dev);
 	struct ixgbe_hw *hw = &adapter->hw;
 	u16 new_port = ntohs(port);
 
+	if (type != UDP_TUNNEL_VXLAN)
+		return;
+
 	if (!(adapter->flags & IXGBE_FLAG_VXLAN_OFFLOAD_CAPABLE))
 		return;
 
@@ -8345,13 +8350,17 @@ static void ixgbe_add_vxlan_port(struct net_device *dev, sa_family_t sa_family,
  * @dev: The port's netdev
  * @sa_family: Socket Family that VXLAN is notifying us about
  * @port: UDP port number that VXLAN stopped listening to
+ * @type: Tunnel type
  **/
 static void ixgbe_del_vxlan_port(struct net_device *dev, sa_family_t sa_family,
-				 __be16 port)
+				 __be16 port, u32 type)
 {
 	struct ixgbe_adapter *adapter = netdev_priv(dev);
 	u16 new_port = ntohs(port);
 
+	if (type != UDP_TUNNEL_VXLAN)
+		return;
+
 	if (!(adapter->flags & IXGBE_FLAG_VXLAN_OFFLOAD_CAPABLE))
 		return;
 
@@ -8663,8 +8672,8 @@ static const struct net_device_ops ixgbe_netdev_ops = {
 	.ndo_dfwd_add_station	= ixgbe_fwd_add,
 	.ndo_dfwd_del_station	= ixgbe_fwd_del,
 #ifdef CONFIG_IXGBE_VXLAN
-	.ndo_add_vxlan_port	= ixgbe_add_vxlan_port,
-	.ndo_del_vxlan_port	= ixgbe_del_vxlan_port,
+	.ndo_add_udp_tunnel_port	= ixgbe_add_vxlan_port,
+	.ndo_del_udp_tunnel_port	= ixgbe_del_vxlan_port,
 #endif /* CONFIG_IXGBE_VXLAN */
 	.ndo_features_check	= ixgbe_features_check,
 };
drivers/net/ethernet/mellanox/mlx4/en_netdev.c +15 -6
index 886e1bc..bd8f240 100644
@@ -39,6 +39,7 @@
 #include <linux/hash.h>
 #include <net/ip.h>
 #include <net/busy_poll.h>
+#include <net/udp_tunnel.h>
 #include <net/vxlan.h>
 
 #include <linux/mlx4/driver.h>
@@ -2402,11 +2403,15 @@ static void mlx4_en_del_vxlan_offloads(struct work_struct *work)
 }
 
 static void mlx4_en_add_vxlan_port(struct  net_device *dev,
-				   sa_family_t sa_family, __be16 port)
+				   sa_family_t sa_family, __be16 port,
+				   u32 type)
 {
 	struct mlx4_en_priv *priv = netdev_priv(dev);
 	__be16 current_port;
 
+	if (type != UDP_TUNNEL_VXLAN)
+		return;
+
 	if (priv->mdev->dev->caps.tunnel_offload_mode != MLX4_TUNNEL_OFFLOAD_MODE_VXLAN)
 		return;
 
@@ -2425,11 +2430,15 @@ static void mlx4_en_add_vxlan_port(struct  net_device *dev,
 }
 
 static void mlx4_en_del_vxlan_port(struct  net_device *dev,
-				   sa_family_t sa_family, __be16 port)
+				   sa_family_t sa_family, __be16 port,
+				   u32 type)
 {
 	struct mlx4_en_priv *priv = netdev_priv(dev);
 	__be16 current_port;
 
+	if (type != UDP_TUNNEL_VXLAN)
+		return;
+
 	if (priv->mdev->dev->caps.tunnel_offload_mode != MLX4_TUNNEL_OFFLOAD_MODE_VXLAN)
 		return;
 
@@ -2509,8 +2518,8 @@ static const struct net_device_ops mlx4_netdev_ops = {
 #endif
 	.ndo_get_phys_port_id	= mlx4_en_get_phys_port_id,
 #ifdef CONFIG_MLX4_EN_VXLAN
-	.ndo_add_vxlan_port	= mlx4_en_add_vxlan_port,
-	.ndo_del_vxlan_port	= mlx4_en_del_vxlan_port,
+	.ndo_add_udp_tunnel_port	= mlx4_en_add_vxlan_port,
+	.ndo_del_udp_tunnel_port	= mlx4_en_del_vxlan_port,
 	.ndo_features_check	= mlx4_en_features_check,
 #endif
 	.ndo_set_tx_maxrate	= mlx4_en_set_tx_maxrate,
@@ -2547,8 +2556,8 @@ static const struct net_device_ops mlx4_netdev_ops_master = {
 #endif
 	.ndo_get_phys_port_id	= mlx4_en_get_phys_port_id,
 #ifdef CONFIG_MLX4_EN_VXLAN
-	.ndo_add_vxlan_port	= mlx4_en_add_vxlan_port,
-	.ndo_del_vxlan_port	= mlx4_en_del_vxlan_port,
+	.ndo_add_udp_tunnel_port	= mlx4_en_add_vxlan_port,
+	.ndo_del_udp_tunnel_port	= mlx4_en_del_vxlan_port,
 	.ndo_features_check	= mlx4_en_features_check,
 #endif
 	.ndo_set_tx_maxrate	= mlx4_en_set_tx_maxrate,
drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c +13 -4
index d448145..18d384f 100644
@@ -17,6 +17,7 @@
 #include <linux/log2.h>
 #include <linux/pci.h>
 #ifdef CONFIG_QLCNIC_VXLAN
+#include <net/udp_tunnel.h>
 #include <net/vxlan.h>
 #endif
 
@@ -475,11 +476,15 @@ static int qlcnic_get_phys_port_id(struct net_device *netdev,
 
 #ifdef CONFIG_QLCNIC_VXLAN
 static void qlcnic_add_vxlan_port(struct net_device *netdev,
-				  sa_family_t sa_family, __be16 port)
+				  sa_family_t sa_family, __be16 port,
+				  u32 type)
 {
 	struct qlcnic_adapter *adapter = netdev_priv(netdev);
 	struct qlcnic_hardware_context *ahw = adapter->ahw;
 
+	if (type != UDP_TUNNEL_VXLAN)
+		return;
+
 	/* Adapter supports only one VXLAN port. Use very first port
 	 * for enabling offload
 	 */
@@ -497,11 +502,15 @@ static void qlcnic_add_vxlan_port(struct net_device *netdev,
 }
 
 static void qlcnic_del_vxlan_port(struct net_device *netdev,
-				  sa_family_t sa_family, __be16 port)
+				  sa_family_t sa_family, __be16 port,
+				  u32 type)
 {
 	struct qlcnic_adapter *adapter = netdev_priv(netdev);
 	struct qlcnic_hardware_context *ahw = adapter->ahw;
 
+	if (type != UDP_TUNNEL_VXLAN)
+		return;
+
 	if (!qlcnic_encap_rx_offload(adapter) || !ahw->vxlan_port_count ||
 	    (ahw->vxlan_port != ntohs(port)))
 		return;
@@ -539,8 +548,8 @@ static const struct net_device_ops qlcnic_netdev_ops = {
 	.ndo_fdb_dump		= qlcnic_fdb_dump,
 	.ndo_get_phys_port_id	= qlcnic_get_phys_port_id,
 #ifdef CONFIG_QLCNIC_VXLAN
-	.ndo_add_vxlan_port	= qlcnic_add_vxlan_port,
-	.ndo_del_vxlan_port	= qlcnic_del_vxlan_port,
+	.ndo_add_udp_tunnel_port	= qlcnic_add_vxlan_port,
+	.ndo_del_udp_tunnel_port	= qlcnic_del_vxlan_port,
 	.ndo_features_check	= qlcnic_features_check,
 #endif
 #ifdef CONFIG_NET_POLL_CONTROLLER
drivers/net/vxlan.c +10 -10
index 6369a57..463f41a 100644
@@ -628,9 +628,9 @@ static void vxlan_notify_add_rx_port(struct vxlan_sock *vs)
 
 	rcu_read_lock();
 	for_each_netdev_rcu(net, dev) {
-		if (dev->netdev_ops->ndo_add_vxlan_port)
-			dev->netdev_ops->ndo_add_vxlan_port(dev, sa_family,
-							    port);
+		if (dev->netdev_ops->ndo_add_udp_tunnel_port)
+			dev->netdev_ops->ndo_add_udp_tunnel_port(dev, sa_family,
+							port, UDP_TUNNEL_VXLAN);
 	}
 	rcu_read_unlock();
 }
@@ -646,9 +646,9 @@ static void vxlan_notify_del_rx_port(struct vxlan_sock *vs)
 
 	rcu_read_lock();
 	for_each_netdev_rcu(net, dev) {
-		if (dev->netdev_ops->ndo_del_vxlan_port)
-			dev->netdev_ops->ndo_del_vxlan_port(dev, sa_family,
-							    port);
+		if (dev->netdev_ops->ndo_del_udp_tunnel_port)
+			dev->netdev_ops->ndo_del_udp_tunnel_port(dev, sa_family,
+							port, UDP_TUNNEL_VXLAN);
 	}
 	rcu_read_unlock();
 
@@ -2422,9 +2422,9 @@ static struct device_type vxlan_type = {
 	.name = "vxlan",
 };
 
-/* Calls the ndo_add_vxlan_port of the caller in order to
+/* Calls the ndo_add_udp_tunnel_port of the caller in order to
  * supply the listening VXLAN udp ports. Callers are expected
- * to implement the ndo_add_vxlan_port.
+ * to implement the ndo_add_udp_tunnel_port.
  */
 void vxlan_get_rx_port(struct net_device *dev)
 {
@@ -2440,8 +2440,8 @@ void vxlan_get_rx_port(struct net_device *dev)
 		hlist_for_each_entry_rcu(vs, &vn->sock_list[i], hlist) {
 			port = inet_sk(vs->sock->sk)->inet_sport;
 			sa_family = vxlan_get_sk_family(vs);
-			dev->netdev_ops->ndo_add_vxlan_port(dev, sa_family,
-							    port);
+			dev->netdev_ops->ndo_add_udp_tunnel_port(dev, sa_family,
+							port, UDP_TUNNEL_VXLAN);
 		}
 	}
 	spin_unlock(&vn->sock_lock);
include/linux/netdevice.h +22 -17
index 4ac653b..dbbab3b 100644
@@ -1004,18 +1004,24 @@ typedef u16 (*select_queue_fallback_t)(struct net_device *dev,
  *	not implement this, it is assumed that the hw is not able to have
  *	multiple net devices on single physical port.
  *
- * void (*ndo_add_vxlan_port)(struct  net_device *dev,
- *			      sa_family_t sa_family, __be16 port);
- *	Called by vxlan to notiy a driver about the UDP port and socket
- *	address family that vxlan is listnening to. It is called only when
- *	a new port starts listening. The operation is protected by the
- *	vxlan_net->sock_lock.
- *
- * void (*ndo_del_vxlan_port)(struct  net_device *dev,
- *			      sa_family_t sa_family, __be16 port);
- *	Called by vxlan to notify the driver about a UDP port and socket
- *	address family that vxlan is not listening to anymore. The operation
- *	is protected by the vxlan_net->sock_lock.
+ * void (*ndo_add_udp_tunnel_port)(struct  net_device *dev,
+ *			      sa_family_t sa_family, __be16 port, u32 type);
+ *	Called by UDP based tunnel modules to notify a driver about a UDP
+ *	port and socket address family that the tunnel is listening to. It is
+ *	called only when a new port starts listening. The operation is
+ *	protected by tunnel socket sock_lock which is per tunnel type.
+ *	If the driver implementation shares resources between different types
+ *	of tunnels, it should implement it's own locking to safeguard against
+ *	simultaneous access.
+ *
+ * void (*ndo_del_udp_tunnel_port)(struct  net_device *dev,
+ *			      sa_family_t sa_family, __be16 port, u32 type);
+ *	Called by UDP based tunnel modules to notify the driver about a UDP port
+ *	and socket address family that tunnel is not listening to anymore.
+ *	The operation is protected protected by tunnel socket sock_lock which
+ *	is per tunnel type. If the driver implementation shares resources
+ *	between different types of tunnels, it should implement it's own locking
+ *	to safeguard against simultaneous access.
  *
  * void* (*ndo_dfwd_add_station)(struct net_device *pdev,
  *				 struct net_device *dev)
@@ -1209,13 +1215,12 @@ struct net_device_ops {
 							struct netdev_phys_item_id *ppid);
 	int			(*ndo_get_phys_port_name)(struct net_device *dev,
 							  char *name, size_t len);
-	void			(*ndo_add_vxlan_port)(struct  net_device *dev,
+	void			(*ndo_add_udp_tunnel_port)(struct  net_device *dev,
 						      sa_family_t sa_family,
-						      __be16 port);
-	void			(*ndo_del_vxlan_port)(struct  net_device *dev,
+						      __be16 port, u32 type);
+	void			(*ndo_del_udp_tunnel_port)(struct  net_device *dev,
 						      sa_family_t sa_family,
-						      __be16 port);
-
+						      __be16 port, u32 type);
 	void*			(*ndo_dfwd_add_station)(struct net_device *pdev,
 							struct net_device *dev);
 	void			(*ndo_dfwd_del_station)(struct net_device *pdev,
include/net/udp_tunnel.h +5 -0
index cb2f89f..eb44d5f 100644
@@ -9,6 +9,11 @@
 #include <net/addrconf.h>
 #endif
 
+enum udp_tunnel_type {
+	UDP_TUNNEL_VXLAN,
+	UDP_TUNNEL_GENEVE,
+};
+
 struct udp_port_cfg {
 	u8			family;
 
Signature · 1 line
1.8.1.4
#2 lore raw

PATCH v4 3/6 i40e: Generalize the flow for udp based tunnels

In reply to Anjali Singhai Jain

This patch generalizes the driver flow to make room for more than just VXLAN tunnel by defining a common data structure with tunnel type.

---
 drivers/net/ethernet/intel/i40e/i40e.h      | 11 ++++--
 drivers/net/ethernet/intel/i40e/i40e_main.c | 54 ++++++++++++++++-------------
 drivers/net/ethernet/intel/i40e/i40e_txrx.c |  6 ++--
 drivers/net/ethernet/intel/i40e/i40e_txrx.h |  2 +-
 4 files changed, 41 insertions(+), 32 deletions(-)
drivers/net/ethernet/intel/i40e/i40e.h +8 -3
index 6c4d154..c24008f 100644
@@ -246,6 +246,11 @@ struct i40e_tc_configuration {
 	struct i40e_tc_info tc_info[I40E_MAX_TRAFFIC_CLASS];
 };
 
+struct i40e_udp_port_config {
+	__be16 index;
+	u8 type;
+};
+
 /* struct that defines the Ethernet device */
 struct i40e_pf {
 	struct pci_dev *pdev;
@@ -282,8 +287,8 @@ struct i40e_pf {
 	u32 fd_atr_cnt;
 	u32 fd_tcp_rule;
 
-	__be16  vxlan_ports[I40E_MAX_PF_UDP_OFFLOAD_PORTS];
-	u16 pending_vxlan_bitmap;
+	struct i40e_udp_port_config udp_ports[I40E_MAX_PF_UDP_OFFLOAD_PORTS];
+	u16 pending_udp_bitmap;
 
 	enum i40e_interrupt_policy int_policy;
 	u16 rx_itr_default;
@@ -321,7 +326,7 @@ struct i40e_pf {
 #define I40E_FLAG_FD_ATR_ENABLED		BIT_ULL(22)
 #define I40E_FLAG_PTP				BIT_ULL(25)
 #define I40E_FLAG_MFP_ENABLED			BIT_ULL(26)
-#define I40E_FLAG_VXLAN_FILTER_SYNC		BIT_ULL(27)
+#define I40E_FLAG_UDP_FILTER_SYNC              BIT_ULL(27)
 #define I40E_FLAG_PORT_ID_VALID			BIT_ULL(28)
 #define I40E_FLAG_DCB_CAPABLE			BIT_ULL(29)
 #define I40E_FLAG_RSS_AQ_CAPABLE		BIT_ULL(31)
drivers/net/ethernet/intel/i40e/i40e_main.c +29 -25

141 lines not on this page · raw message

drivers/net/ethernet/intel/i40e/i40e_txrx.c +3 -3
index d67ac85..2729a48 100644
@@ -2006,7 +2006,7 @@ static void i40e_atr(struct i40e_ring *tx_ring, struct sk_buff *skb,
 	if (!(tx_flags & (I40E_TX_FLAGS_IPV4 | I40E_TX_FLAGS_IPV6)))
 		return;
 
-	if (!(tx_flags & I40E_TX_FLAGS_VXLAN_TUNNEL)) {
+	if (!(tx_flags & I40E_TX_FLAGS_UDP_TUNNEL)) {
 		/* snag network header to get L4 type and address */
 		hdr.network = skb_network_header(skb);
 
@@ -2091,7 +2091,7 @@ static void i40e_atr(struct i40e_ring *tx_ring, struct sk_buff *skb,
 		     I40E_TXD_FLTR_QW1_FD_STATUS_SHIFT;
 
 	dtype_cmd |= I40E_TXD_FLTR_QW1_CNT_ENA_MASK;
-	if (!(tx_flags & I40E_TX_FLAGS_VXLAN_TUNNEL))
+	if (!(tx_flags & I40E_TX_FLAGS_UDP_TUNNEL))
 		dtype_cmd |=
 			((u32)I40E_FD_ATR_STAT_IDX(pf->hw.pf_id) <<
 			I40E_TXD_FLTR_QW1_CNTINDEX_SHIFT) &
@@ -2324,7 +2324,7 @@ static void i40e_tx_enable_csum(struct sk_buff *skb, u32 *tx_flags,
 			oudph = udp_hdr(skb);
 			oiph = ip_hdr(skb);
 			l4_tunnel = I40E_TXD_CTX_UDP_TUNNELING;
-			*tx_flags |= I40E_TX_FLAGS_VXLAN_TUNNEL;
+			*tx_flags |= I40E_TX_FLAGS_UDP_TUNNEL;
 			break;
 		case IPPROTO_GRE:
 			l4_tunnel = I40E_TXD_CTX_GRE_TUNNELING;
drivers/net/ethernet/intel/i40e/i40e_txrx.h +1 -1
index dccc1eb..3f081e2 100644
@@ -163,7 +163,7 @@ enum i40e_dyn_idx_t {
 #define I40E_TX_FLAGS_FSO		BIT(7)
 #define I40E_TX_FLAGS_TSYN		BIT(8)
 #define I40E_TX_FLAGS_FD_SB		BIT(9)
-#define I40E_TX_FLAGS_VXLAN_TUNNEL	BIT(10)
+#define I40E_TX_FLAGS_UDP_TUNNEL	BIT(10)
 #define I40E_TX_FLAGS_VLAN_MASK		0xffff0000
 #define I40E_TX_FLAGS_VLAN_PRIO_MASK	0xe0000000
 #define I40E_TX_FLAGS_VLAN_PRIO_SHIFT	29
Signature · 1 line
1.8.1.4
#3 lore raw

PATCH v4 3/6 i40e: Generalize the flow for udp based tunnels

Quoted 11 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On Behalf Of Anjali Singhai Jain
Sent: Tuesday, November 10, 2015 9:57 AM
To: intel-wired-lan at lists.osuosl.org
Subject: [Intel-wired-lan] [PATCH v4 3/6] i40e: Generalize the flow for udp based tunnels

This patch generalizes the driver flow to make room for more than just VXLAN tunnel by defining a common data structure with tunnel type.

Quoted 8 lines
---
 drivers/net/ethernet/intel/i40e/i40e.h      | 11 ++++--
 drivers/net/ethernet/intel/i40e/i40e_main.c | 54 ++++++++++++++++-------
------  drivers/net/ethernet/intel/i40e/i40e_txrx.c |  6 ++--
drivers/net/ethernet/intel/i40e/i40e_txrx.h |  2 +-
 4 files changed, 41 insertions(+), 32 deletions(-)

Patch code changes correctly applied

#4 lore raw

PATCH v4 4/6 geneve: Add geneve udp port offload for ethernet

In reply to Anjali Singhai Jain

Call ndo_ops to add/del UDP ports to a device that supports geneve offload.

---
 drivers/net/geneve.c | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)
drivers/net/geneve.c +23 -0
index de5c30c..f77db6ab 100644
@@ -371,8 +371,11 @@ static struct socket *geneve_create_sock(struct net *net, bool ipv6,
 
 static void geneve_notify_add_rx_port(struct geneve_sock *gs)
 {
+	struct net_device *dev;
 	struct sock *sk = gs->sock->sk;
+	struct net *net = sock_net(sk);
 	sa_family_t sa_family = sk->sk_family;
+	__be16 port = inet_sk(sk)->inet_sport;
 	int err;
 
 	if (sa_family == AF_INET) {
@@ -381,6 +384,14 @@ static void geneve_notify_add_rx_port(struct geneve_sock *gs)
 			pr_warn("geneve: udp_add_offload failed with status %d\n",
 				err);
 	}
+	rcu_read_lock();
+	for_each_netdev_rcu(net, dev) {
+		if (dev->netdev_ops->ndo_add_udp_tunnel_port)
+			dev->netdev_ops->ndo_add_udp_tunnel_port(dev,
+					       sa_family,
+					       port, UDP_TUNNEL_GENEVE);
+	}
+	rcu_read_unlock();
 }
 
 static int geneve_hlen(struct genevehdr *gh)
@@ -521,8 +532,20 @@ static struct geneve_sock *geneve_socket_create(struct net *net, __be16 port,
 
 static void geneve_notify_del_rx_port(struct geneve_sock *gs)
 {
+	struct net_device *dev;
 	struct sock *sk = gs->sock->sk;
+	struct net *net = sock_net(sk);
 	sa_family_t sa_family = sk->sk_family;
+	__be16 port = inet_sk(sk)->inet_sport;
+
+	rcu_read_lock();
+	for_each_netdev_rcu(net, dev) {
+		if (dev->netdev_ops->ndo_del_udp_tunnel_port)
+			dev->netdev_ops->ndo_del_udp_tunnel_port(dev,
+					       sa_family,
+					       port, UDP_TUNNEL_GENEVE);
+	}
+	rcu_read_unlock();
 
 	if (sa_family == AF_INET)
 		udp_del_offload(&gs->udp_offloads);
Signature · 1 line
1.8.1.4
#5 lore raw

PATCH v4 5/6 i40e:Add geneve tunnel offload support

In reply to Anjali Singhai Jain

This patch adds driver hooks to implement ndo_ops to add/del udp port in the HW to identify GENEVE tunnels.

Also cleans up the features_check path now that we support multiple udp based tunnels.

Add a spin_lock to guard the common data structure for the udp based tunnels.

---
 drivers/net/ethernet/intel/i40e/i40e.h      |  2 +
 drivers/net/ethernet/intel/i40e/i40e_main.c | 61 ++++++++++++++++++++++-------
 drivers/net/ethernet/intel/i40e/i40e_txrx.c |  2 +-
 3 files changed, 50 insertions(+), 15 deletions(-)
drivers/net/ethernet/intel/i40e/i40e.h +2 -0
index c24008f..08a0a00 100644
@@ -338,6 +338,7 @@ struct i40e_pf {
 #define I40E_FLAG_MULTIPLE_TCP_UDP_RSS_PCTYPE	BIT_ULL(38)
 #define I40E_FLAG_LINK_POLLING_ENABLED		BIT_ULL(39)
 #define I40E_FLAG_VEB_MODE_ENABLED		BIT_ULL(40)
+#define I40E_FLAG_GENEVE_OFFLOAD_CAPABLE	BIT_ULL(41)
 #define I40E_FLAG_NO_PCI_LINK_CHECK		BIT_ULL(42)
 
 	/* tracks features that get auto disabled by errors */
@@ -422,6 +423,7 @@ struct i40e_pf {
 
 	u32 ioremap_len;
 	u32 fd_inv;
+	spinlock_t udp_tunnel_lock;
 };
 
 struct i40e_mac_filter {
drivers/net/ethernet/intel/i40e/i40e_main.c +47 -14

191 lines not on this page · raw message

drivers/net/ethernet/intel/i40e/i40e_txrx.c +1 -1
index 2729a48..5dfe15c 100644
@@ -1383,7 +1383,7 @@ static inline void i40e_rx_checksum(struct i40e_vsi *vsi,
 	if (rx_error & BIT(I40E_RX_DESC_ERROR_PPRS_SHIFT))
 		return;
 
-	/* If VXLAN traffic has an outer UDPv4 checksum we need to check
+	/* If VXLAN/GENEVE traffic has an outer UDPv4 checksum we need to check
 	 * it in the driver, hardware does not do it for us.
 	 * Since L3L4P bit was set we assume a valid IHL value (>=5)
 	 * so the total length of IPv4 header is IHL*4 bytes
Signature · 1 line
1.8.1.4
#6 lore raw

PATCH v4 5/6 i40e:Add geneve tunnel offload support

Quoted 17 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On Behalf Of Anjali Singhai Jain
Sent: Tuesday, November 10, 2015 9:57 AM
To: intel-wired-lan at lists.osuosl.org
Subject: [Intel-wired-lan] [PATCH v4 5/6] i40e:Add geneve tunnel offload support

This patch adds driver hooks to implement ndo_ops to add/del udp port in the HW to identify GENEVE tunnels.

Also cleans up the features_check path now that we support multiple udp based tunnels.

Add a spin_lock to guard the common data structure for the udp based tunnels.

Quoted 8 lines
---
 drivers/net/ethernet/intel/i40e/i40e.h      |  2 +
 drivers/net/ethernet/intel/i40e/i40e_main.c | 61
++++++++++++++++++++++-------
drivers/net/ethernet/intel/i40e/i40e_txrx.c |  2 +-
 3 files changed, 50 insertions(+), 15 deletions(-)

Patch code changes correctly applied

#7 lore raw

PATCH v4 6/6 net: Add a generic udp_offload_get_port function

In reply to Anjali Singhai Jain

The new function udp_offload_get_port replaces vxlan_get_rx_port().
This is a generic function that will help replay all udp tunnel ports irrespective of tunnel type. This way when new udp tunnels get added this function need not change.

Note: Drivers besides i40e are compile tested with this change.

v2: fix a compile issue with redefinition of the function.

---
 drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c |  5 +++--
 drivers/net/ethernet/broadcom/bnxt/bnxt.c        |  3 ++-
 drivers/net/ethernet/emulex/benet/be_main.c      |  3 ++-
 drivers/net/ethernet/intel/fm10k/fm10k_netdev.c  |  3 ++-
 drivers/net/ethernet/intel/i40e/i40e_main.c      |  5 ++---
 drivers/net/ethernet/intel/ixgbe/ixgbe_main.c    |  5 +++--
 drivers/net/ethernet/mellanox/mlx4/en_netdev.c   |  3 ++-
 drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c |  3 ++-
 drivers/net/vxlan.c                              | 28 ++----------------------
 include/linux/netdevice.h                        |  2 ++
 include/net/protocol.h                           |  2 ++
 include/net/vxlan.h                              |  8 -------
 net/ipv4/udp_offload.c                           | 25 +++++++++++++++++++++
 13 files changed, 49 insertions(+), 46 deletions(-)
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c +3 -2
index 3a863dc..299dca7 100644
@@ -60,6 +60,7 @@
 #include <linux/semaphore.h>
 #include <linux/stringify.h>
 #include <linux/vmalloc.h>
+#include <net/protocol.h>
 
 #include "bnx2x.h"
 #include "bnx2x_init.h"
@@ -10293,7 +10294,7 @@ sp_rtnl_not_reset:
 			netdev_info(bp->dev,
 				    "Deleted vxlan dest port %d", port);
 			bp->vxlan_dst_port = 0;
-			vxlan_get_rx_port(bp->dev);
+			udp_offload_get_port(bp->dev);
 		}
 	}
 #endif
@@ -12499,7 +12500,7 @@ static int bnx2x_open(struct net_device *dev)
 
 #ifdef CONFIG_BNX2X_VXLAN
 	if (IS_PF(bp))
-		vxlan_get_rx_port(dev);
+		udp_offload_get_port(dev);
 #endif
 
 	return 0;
drivers/net/ethernet/broadcom/bnxt/bnxt.c +2 -1
index af68428..47184d0 100644
@@ -39,6 +39,7 @@
 #include <net/ip6_checksum.h>
 #if defined(CONFIG_VXLAN) || defined(CONFIG_VXLAN_MODULE)
 #include <net/vxlan.h>
+#include <net/protocol.h>
 #include <net/udp_tunnel.h>
 #endif
 #ifdef CONFIG_NET_RX_BUSY_POLL
@@ -4579,7 +4580,7 @@ static int __bnxt_open_nic(struct bnxt *bp, bool irq_re_init, bool link_re_init)
 
 	if (irq_re_init) {
 #if defined(CONFIG_VXLAN) || defined(CONFIG_VXLAN_MODULE)
-		vxlan_get_rx_port(bp->dev);
+		udp_offload_get_port(bp->dev);
 #endif
 		if (!bnxt_hwrm_tunnel_dst_port_alloc(
 				bp, htons(0x17c1),
drivers/net/ethernet/emulex/benet/be_main.c +2 -1
index 6af9f27..5d579eb 100644
@@ -25,6 +25,7 @@
 #include <net/busy_poll.h>
 #include <net/udp_tunnel.h>
 #include <net/vxlan.h>
+#include <net/protocol.h>
 
 MODULE_VERSION(DRV_VER);
 MODULE_DESCRIPTION(DRV_DESC " " DRV_VER);
@@ -3606,7 +3607,7 @@ static int be_open(struct net_device *netdev)
 
 #ifdef CONFIG_BE2NET_VXLAN
 	if (skyhawk_chip(adapter))
-		vxlan_get_rx_port(netdev);
+		udp_offload_get_port(netdev);
 #endif
 
 	return 0;
drivers/net/ethernet/intel/fm10k/fm10k_netdev.c +2 -1
index bf7af95..cefa5ab 100644
@@ -23,6 +23,7 @@
 #if IS_ENABLED(CONFIG_FM10K_VXLAN)
 #include <net/udp_tunnel.h>
 #include <net/vxlan.h>
+#include <net/protocol.h>
 #endif /* CONFIG_FM10K_VXLAN */
 
 /**
@@ -573,7 +574,7 @@ int fm10k_open(struct net_device *netdev)
 
 #if IS_ENABLED(CONFIG_FM10K_VXLAN)
 	/* update VXLAN port configuration */
-	vxlan_get_rx_port(netdev);
+	udp_offload_get_port(netdev);
 
 #endif
 	fm10k_up(interface);
drivers/net/ethernet/intel/i40e/i40e_main.c +2 -3
index 1ce65a1..73fc27a 100644
@@ -34,6 +34,7 @@
 #if IS_ENABLED(CONFIG_GENEVE)
 #include <net/geneve.h>
 #endif
+#include <net/protocol.h>
 
 const char i40e_driver_name[] = "i40e";
 static const char i40e_driver_string[] =
@@ -5298,9 +5299,7 @@ int i40e_open(struct net_device *netdev)
 						       TCP_FLAG_CWR) >> 16);
 	wr32(&pf->hw, I40E_GLLAN_TSOMSK_L, be32_to_cpu(TCP_FLAG_CWR) >> 16);
 
-#if IS_ENABLED(CONFIG_VXLAN)
-	vxlan_get_rx_port(netdev);
-#endif
+	udp_offload_get_port(netdev);
 
 	return 0;
 }
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +3 -2
index d7ad9d9..137a637 100644
@@ -52,6 +52,7 @@
 #include <scsi/fc/fc_fcoe.h>
 #include <net/udp_tunnel.h>
 #include <net/vxlan.h>
+#include <net/protocol.h>
 
 #ifdef CONFIG_OF
 #include <linux/of_net.h>
@@ -6039,7 +6040,7 @@ static int ixgbe_open(struct net_device *netdev)
 
 	ixgbe_clear_vxlan_port(adapter);
 #ifdef CONFIG_IXGBE_VXLAN
-	vxlan_get_rx_port(netdev);
+	udp_offload_get_port(netdev);
 #endif
 
 	return 0;
@@ -7118,7 +7119,7 @@ static void ixgbe_service_task(struct work_struct *work)
 #ifdef CONFIG_IXGBE_VXLAN
 	if (adapter->flags2 & IXGBE_FLAG2_VXLAN_REREG_NEEDED) {
 		adapter->flags2 &= ~IXGBE_FLAG2_VXLAN_REREG_NEEDED;
-		vxlan_get_rx_port(adapter->netdev);
+		udp_offload_get_port(adapter->netdev);
 	}
 #endif /* CONFIG_IXGBE_VXLAN */
 	ixgbe_reset_subtask(adapter);
drivers/net/ethernet/mellanox/mlx4/en_netdev.c +2 -1
index bd8f240..ffc43bb 100644
@@ -41,6 +41,7 @@
 #include <net/busy_poll.h>
 #include <net/udp_tunnel.h>
 #include <net/vxlan.h>
+#include <net/protocol.h>
 
 #include <linux/mlx4/driver.h>
 #include <linux/mlx4/device.h>
@@ -1714,7 +1715,7 @@ int mlx4_en_start_port(struct net_device *dev)
 
 #ifdef CONFIG_MLX4_EN_VXLAN
 	if (priv->mdev->dev->caps.tunnel_offload_mode == MLX4_TUNNEL_OFFLOAD_MODE_VXLAN)
-		vxlan_get_rx_port(dev);
+		udp_offload_get_port(dev);
 #endif
 	priv->port_up = true;
 	netif_tx_start_all_queues(dev);
drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c +2 -1
index 18d384f..203b328 100644
@@ -19,6 +19,7 @@
 #ifdef CONFIG_QLCNIC_VXLAN
 #include <net/udp_tunnel.h>
 #include <net/vxlan.h>
+#include <net/protocol.h>
 #endif
 
 #include "qlcnic.h"
@@ -2025,7 +2026,7 @@ qlcnic_attach(struct qlcnic_adapter *adapter)
 
 #ifdef CONFIG_QLCNIC_VXLAN
 	if (qlcnic_encap_rx_offload(adapter))
-		vxlan_get_rx_port(netdev);
+		udp_offload_get_port(netdev);
 #endif
 
 	adapter->is_up = QLCNIC_ADAPTER_UP_MAGIC;
drivers/net/vxlan.c +2 -26
index 463f41a..2ccb15f 100644
@@ -2422,32 +2422,6 @@ static struct device_type vxlan_type = {
 	.name = "vxlan",
 };
 
-/* Calls the ndo_add_udp_tunnel_port of the caller in order to
- * supply the listening VXLAN udp ports. Callers are expected
- * to implement the ndo_add_udp_tunnel_port.
- */
-void vxlan_get_rx_port(struct net_device *dev)
-{
-	struct vxlan_sock *vs;
-	struct net *net = dev_net(dev);
-	struct vxlan_net *vn = net_generic(net, vxlan_net_id);
-	sa_family_t sa_family;
-	__be16 port;
-	unsigned int i;
-
-	spin_lock(&vn->sock_lock);
-	for (i = 0; i < PORT_HASH_SIZE; ++i) {
-		hlist_for_each_entry_rcu(vs, &vn->sock_list[i], hlist) {
-			port = inet_sk(vs->sock->sk)->inet_sport;
-			sa_family = vxlan_get_sk_family(vs);
-			dev->netdev_ops->ndo_add_udp_tunnel_port(dev, sa_family,
-							port, UDP_TUNNEL_VXLAN);
-		}
-	}
-	spin_unlock(&vn->sock_lock);
-}
-EXPORT_SYMBOL_GPL(vxlan_get_rx_port);
-
 /* Initialize the device structure. */
 static void vxlan_setup(struct net_device *dev)
 {
@@ -2636,6 +2610,8 @@ static struct vxlan_sock *vxlan_socket_create(struct net *net, bool ipv6,
 
 	/* Initialize the vxlan udp offloads structure */
 	vs->udp_offloads.port = port;
+	vs->udp_offloads.tunnel_type = UDP_TUNNEL_VXLAN;
+	vs->udp_offloads.family = ipv6 ? AF_INET6 : AF_INET;
 	vs->udp_offloads.callbacks.gro_receive  = vxlan_gro_receive;
 	vs->udp_offloads.callbacks.gro_complete = vxlan_gro_complete;
 
include/linux/netdevice.h +2 -0
index dbbab3b..cfe6201 100644
@@ -2059,6 +2059,8 @@ struct udp_offload_callbacks {
 
 struct udp_offload {
 	__be16			 port;
+	u8			 tunnel_type;
+	u8			 family;
 	u8			 ipproto;
 	struct udp_offload_callbacks callbacks;
 };
include/net/protocol.h +2 -0
index d6fcc1f..738bfc6 100644
@@ -110,6 +110,8 @@ void inet_unregister_protosw(struct inet_protosw *p);
 int  udp_add_offload(struct udp_offload *prot);
 void udp_del_offload(struct udp_offload *prot);
 
+void udp_offload_get_port(struct net_device *dev);
+
 #if IS_ENABLED(CONFIG_IPV6)
 int inet6_add_protocol(const struct inet6_protocol *prot, unsigned char num);
 int inet6_del_protocol(const struct inet6_protocol *prot, unsigned char num);
include/net/vxlan.h +0 -8
index c1c899c..926455e 100644
@@ -242,14 +242,6 @@ static inline netdev_features_t vxlan_features_check(struct sk_buff *skb,
 /* IPv6 header + UDP + VXLAN + Ethernet header */
 #define VXLAN6_HEADROOM (40 + 8 + 8 + 14)
 
-#if IS_ENABLED(CONFIG_VXLAN)
-void vxlan_get_rx_port(struct net_device *netdev);
-#else
-static inline void vxlan_get_rx_port(struct net_device *netdev)
-{
-}
-#endif
-
 static inline unsigned short vxlan_get_sk_family(struct vxlan_sock *vs)
 {
 	return vs->sock->sk->sk_family;
net/ipv4/udp_offload.c +25 -0
index f938616..30aa84c 100644
@@ -290,6 +290,31 @@ unlock:
 }
 EXPORT_SYMBOL(udp_del_offload);
 
+void udp_offload_get_port(struct net_device *dev)
+{
+#if IS_ENABLED(CONFIG_VXLAN) || IS_ENABLED(CONFIG_GENEVE)
+	struct udp_offload_priv __rcu **head = &udp_offload_base;
+	struct udp_offload_priv *uo_priv;
+	struct udp_offload *uo;
+
+	rcu_read_lock();
+	uo_priv = rcu_dereference(udp_offload_base);
+	for (; uo_priv != NULL; uo_priv = rcu_dereference(uo_priv->next)) {
+		/* call the right add port */
+		uo = uo_priv->offload;
+		if (uo && dev->netdev_ops->ndo_add_udp_tunnel_port)
+			dev->netdev_ops->ndo_add_udp_tunnel_port(dev,
+							uo->family,
+							uo->port,
+							uo->tunnel_type);
+
+		head = &uo_priv->next;
+	}
+	rcu_read_unlock();
+#endif
+}
+EXPORT_SYMBOL(udp_offload_get_port);
+
 struct sk_buff **udp_gro_receive(struct sk_buff **head, struct sk_buff *skb,
 				 struct udphdr *uh)
 {
Signature · 1 line
1.8.1.4
#8 lore raw

PATCH v4 6/6 net: Add a generic udp_offload_get_port function

Quoted 10 lines · Anjali Singhai Jain

The new function udp_offload_get_port replaces vxlan_get_rx_port().
This is a generic function that will help replay all udp tunnel ports irrespective of tunnel type. This way when new udp tunnels get added this function need not change.

Note: Drivers besides i40e are compile tested with this change.

v2: fix a compile issue with redefinition of the function.

I don't think that the locking is safe in the patch. The original vxlan_get_rx_port() held vn->sock_lock while calling into drivers but the new udp_offload_get_port() doesn't hold anything except for RCU. i40e is protected because you introduced a new spinlock but I don't think the same thing hold true for other drivers, even if they are only handling VXLAN. There's no guarantee that they are in a safe context when they call this function vs. calls from adding new tunnel ports. Based on our previous conversation about RTNL, I think there are existing drivers that don't meet this so we would have to add new locks to every driver supporting this.

I believe that is really quite simple to just call ndo_add_udp_tunnel_port() from udp_add_offload() while udp_offload_lock() is held (and the opposite on delete). We could also hold this instead of RCU in udp_offload_get_port(). At that point, we wouldn't need any new locking in drivers so I think that this would be simplest and cleanest path forward.

net/ipv4/udp_offload.c unlock: · line 295

Quoted 10 lines

index f938616..30aa84c 100644

net/ipv4/udp_offload.c +3 -0
@@ -290,6 +290,31 @@ unlock:
 }
 EXPORT_SYMBOL(udp_del_offload);
 
+void udp_offload_get_port(struct net_device *dev)
+{
+#if IS_ENABLED(CONFIG_VXLAN) || IS_ENABLED(CONFIG_GENEVE)

I think it is better to not check for VXLAN or Geneve here. This is generic code so it shouldn't make any assumptions about what protocols it is supporting.

#9 lore raw

PATCH v4 6/6 net: Add a generic udp_offload_get_port function

In reply to Anjali Singhai Jain
Quoted 10 lines · Anjali Singhai Jain

The new function udp_offload_get_port replaces vxlan_get_rx_port().
This is a generic function that will help replay all udp tunnel ports irrespective of tunnel type. This way when new udp tunnels get added this function need not change.

Note: Drivers besides i40e are compile tested with this change.

v2: fix a compile issue with redefinition of the function.

I don't think that the locking is safe in the patch. The original vxlan_get_rx_port() held vn->sock_lock while calling into drivers but the new udp_offload_get_port() doesn't hold anything except for RCU. i40e is protected because you introduced a new spinlock but I don't think the same thing hold true for other drivers, even if they are only handling VXLAN. There's no guarantee that they are in a safe context when they call this function vs. calls from adding new tunnel ports. Based on our previous conversation about RTNL, I think there are existing drivers that don't meet this so we would have to add new locks to every driver supporting this.

I believe that is really quite simple to just call ndo_add_udp_tunnel_port() from udp_add_offload() while udp_offload_lock() is held (and the opposite on delete). We could also hold this instead of RCU in udp_offload_get_port(). At that point, we wouldn't need any new locking in drivers so I think that this would be simplest and cleanest path forward.

net/ipv4/udp_offload.c unlock: · line 295

Quoted 10 lines

index f938616..30aa84c 100644

net/ipv4/udp_offload.c +3 -0
@@ -290,6 +290,31 @@ unlock:
 }
 EXPORT_SYMBOL(udp_del_offload);
 
+void udp_offload_get_port(struct net_device *dev)
+{
+#if IS_ENABLED(CONFIG_VXLAN) || IS_ENABLED(CONFIG_GENEVE)

I think it is better to not check for VXLAN or Geneve here. This is generic code so it shouldn't make any assumptions about what protocols it is supporting.

#10 lore raw

PATCH v4 1/6 i40e: Remove CONFIG_I40E_VXLAN

In reply to Anjali Singhai Jain

Hi Anjali,

Quoted 41 lines · Anjali Singhai Jain

If the kernel flag CONFIG_VXLAN is true or CONFIG_VXLAN_MODULE is true,
enable VXLAN offload in the driver.

v2: Fix bisection error for this patch series.

---
?drivers/net/ethernet/intel/i40e/i40e.h??????|??2 -- ?drivers/net/ethernet/intel/i40e/i40e_main.c | 10 ++-------- ?2 files changed, 2 insertions(+), 10 deletions(-)

drivers/net/ethernet/intel/i40e/i40e.h +0 -0
index 8ed759e..6c4d154 100644
@@ -282,11 +282,9 @@ struct i40e_pf {
 ?	u32 fd_atr_cnt;
 ?	u32 fd_tcp_rule;

?
-#if IS_ENABLED(CONFIG_VXLAN)
? __be16??vxlan_ports[I40E_MAX_PF_UDP_OFFLOAD_PORTS];
? u16 pending_vxlan_bitmap;
?
-#endif
? enum i40e_interrupt_policy int_policy;
? u16 rx_itr_default;
? u16 tx_itr_default;

drivers/net/ethernet/intel/i40e/i40e_main.c +0 -0
index b447af6..0235a8a 100644
@@ -6990,13 +6990,13 @@ static void i40e_handle_mdd_event(struct
 i40e_pf *pf)
 ?	i40e_flush(hw);
 ?}

?
-#if IS_ENABLED(CONFIG_VXLAN)

Quoted 8 lines

?/**
? * i40e_sync_vxlan_filters_subtask - Sync the VSI filter list with HW
? * @pf: board private structure
? **/
?static void i40e_sync_vxlan_filters_subtask(struct i40e_pf *pf) ?{
+#if IS_ENABLED(CONFIG_VXLAN)

Direct use of CONFIG_VXLAN is not going to work. What happens in the case where CONFIG_VXLAN=m and CONFIG_I40E=y?

The kernel will load i40e as it loads itself at boot and vxlan module will not get included (because i40e isn't a module so it doesn't run depmod etc) and then it will run and try to call vxlan code and fail because of an unknown symbol since vxlan won't have been started yet.

This is the entire reason why CONFIG_XXX_VXLAN exists. The alternative is to use select VXLAN and force VXLAN on when we enable I40E.

That's the primary reason why we can't directly use CONFIG_VXLAN as a check in driver code.

Regards,
Jake

Quoted 57 lines

? struct i40e_hw *hw = &pf->hw;
? i40e_status ret;
? __be16 port;

drivers/net/ethernet/intel/i40e/i40e_main.c +1 -0
@@ -7030,9 +7030,9 @@ static void
 i40e_sync_vxlan_filters_subtask(struct i40e_pf *pf)
 ?			}
 ?		}
 ?	}
+#endif
 ?}

?
-#endif
?/**
? * i40e_service_task - Run the driver's async subtasks ? * @work: pointer to work_struct containing our data

drivers/net/ethernet/intel/i40e/i40e_main.c +0 -2
@@ -7057,9 +7057,7 @@ static void i40e_service_task(struct
 work_struct *work)
 ?	i40e_watchdog_subtask(pf);
 ?	i40e_fdir_reinit_subtask(pf);
 ?	i40e_sync_filters_subtask(pf);
-#if IS_ENABLED(CONFIG_VXLAN)
 ?	i40e_sync_vxlan_filters_subtask(pf);
-#endif
 ?	i40e_clean_adminq_subtask(pf);

?
? i40e_service_event_complete(pf);

drivers/net/ethernet/intel/i40e/i40e_main.c +0 -0
@@ -8433,7 +8431,6 @@ static int i40e_set_features(struct net_device
 *netdev,
 ?	return 0;
 ?}

?
-#if IS_ENABLED(CONFIG_VXLAN)
?/**
? * i40e_get_vxlan_port_idx - Lookup a possibly offloaded for Rx UDP port
? * @pf: board private structure

drivers/net/ethernet/intel/i40e/i40e_main.c +0 -0
@@ -8528,7 +8525,6 @@ static void i40e_del_vxlan_port(struct
 net_device *netdev,
 ?	}
 ?}

?
-#endif
?static int i40e_get_phys_port_id(struct net_device *netdev,
? ?struct netdev_phys_item_id *ppid)
?{

drivers/net/ethernet/intel/i40e/i40e_main.c +0 -2
@@ -8753,10 +8749,8 @@ static const struct net_device_ops
 i40e_netdev_ops = {
 ?	.ndo_get_vf_config	= i40e_ndo_get_vf_config,
 ?	.ndo_set_vf_link_state	= i40e_ndo_set_vf_link_state,
 ?	.ndo_set_vf_spoofchk	= i40e_ndo_set_vf_spoofchk,
-#if IS_ENABLED(CONFIG_VXLAN)
 ?	.ndo_add_vxlan_port	= i40e_add_vxlan_port,
 ?	.ndo_del_vxlan_port	= i40e_del_vxlan_port,
-#endif
 ?	.ndo_get_phys_port_id	= i40e_get_phys_port_id,
 ?	.ndo_fdb_add		= i40e_ndo_fdb_add,

? .ndo_features_check = i40e_features_check,

#11 lore raw

PATCH v4 1/6 i40e: Remove CONFIG_I40E_VXLAN

Jake this patch doesn't change the use of CONFIG_VXLAN in our driver to guard against a potential issue that you pointed out. Our driver had already changed to using CONFIG_VXLAN in a previous patch.

But I believe that we will still be okay in the scenario that VXLAN module is not loaded because of two reasons
1) We check a flag in sync_vsi_filters if a filter was added or deleted before proceeding to do anything and that will return very quickly from the function when VXLAN or GENEVE module is not loaded.
2) udp_offload_get_port function has empty definitions in the base kernel that will always exist even when the module is not loaded.

Having said that, I am still going to make sure that it's not an issue with a previous patch for our driver. Although the shift to using udp_offload_get_port with this patch series will help alleviate that issue.

Anjali

Quoted 131 lines

-----Original Message-----
From: Keller, Jacob E
Sent: Tuesday, November 10, 2015 10:01 AM
To: intel-wired-lan at lists.osuosl.org; Singhai, Anjali
Subject: Re: [Intel-wired-lan] [PATCH v4 1/6] i40e: Remove CONFIG_I40E_VXLAN

Hi Anjali,

Quoted 40 lines · Anjali Singhai Jain

If the kernel flag CONFIG_VXLAN is true or CONFIG_VXLAN_MODULE is true, enable VXLAN offload in the driver.

v2: Fix bisection error for this patch series.

---
?drivers/net/ethernet/intel/i40e/i40e.h??????|??2 -- ?drivers/net/ethernet/intel/i40e/i40e_main.c | 10 ++-------- ?2 files changed, 2 insertions(+), 10 deletions(-)

drivers/net/ethernet/intel/i40e/i40e.h +0 -2
index 8ed759e..6c4d154 100644
@@ -282,11 +282,9 @@ struct i40e_pf {
 ?	u32 fd_atr_cnt;
 ?	u32 fd_tcp_rule;
 
-#if IS_ENABLED(CONFIG_VXLAN)
 ?	__be16??vxlan_ports[I40E_MAX_PF_UDP_OFFLOAD_PORTS];
 ?	u16 pending_vxlan_bitmap;
 
-#endif
 ?	enum i40e_interrupt_policy int_policy;
 ?	u16 rx_itr_default;
 ?	u16 tx_itr_default;
drivers/net/ethernet/intel/i40e/i40e_main.c +0 -1
index b447af6..0235a8a 100644
@@ -6990,13 +6990,13 @@ static void i40e_handle_mdd_event(struct
 i40e_pf *pf)
 ?	i40e_flush(hw);
 ?}
 
-#if IS_ENABLED(CONFIG_VXLAN)
Quoted 7 lines

?/**
? * i40e_sync_vxlan_filters_subtask - Sync the VSI filter list with HW ? * @pf: board private structure
? **/
?static void i40e_sync_vxlan_filters_subtask(struct i40e_pf *pf) ?{
+#if IS_ENABLED(CONFIG_VXLAN)

Direct use of CONFIG_VXLAN is not going to work. What happens in the case where CONFIG_VXLAN=m and CONFIG_I40E=y?

The kernel will load i40e as it loads itself at boot and vxlan module will not get included (because i40e isn't a module so it doesn't run depmod etc) and then it will run and try to call vxlan code and fail because of an unknown symbol since vxlan won't have been started yet.

This is the entire reason why CONFIG_XXX_VXLAN exists. The alternative is to use select VXLAN and force VXLAN on when we enable I40E.

That's the primary reason why we can't directly use CONFIG_VXLAN as a check in driver code.

Regards,
Jake

Quoted 56 lines

? struct i40e_hw *hw = &pf->hw;
? i40e_status ret;
? __be16 port;

drivers/net/ethernet/intel/i40e/i40e_main.c +1 -1
@@ -7030,9 +7030,9 @@ static void
 i40e_sync_vxlan_filters_subtask(struct i40e_pf *pf)
 ?			}
 ?		}
 ?	}
+#endif
 ?}
 
-#endif

?/**
? * i40e_service_task - Run the driver's async subtasks ? * @work: pointer to work_struct containing our data @@ -7057,9 +7057,7 @@ static void i40e_service_task(struct work_struct *work)
? i40e_watchdog_subtask(pf);
? i40e_fdir_reinit_subtask(pf);
? i40e_sync_filters_subtask(pf);
-#if IS_ENABLED(CONFIG_VXLAN)
? i40e_sync_vxlan_filters_subtask(pf);
-#endif
? i40e_clean_adminq_subtask(pf);

? i40e_service_event_complete(pf);

drivers/net/ethernet/intel/i40e/i40e_main.c +0 -1
@@ -8433,7 +8431,6 @@ static int i40e_set_features(struct net_device
 *netdev,
 ?	return 0;
 ?}
 
-#if IS_ENABLED(CONFIG_VXLAN)

?/**
? * i40e_get_vxlan_port_idx - Lookup a possibly offloaded for Rx UDP port
? * @pf: board private structure

drivers/net/ethernet/intel/i40e/i40e_main.c +0 -1
@@ -8528,7 +8525,6 @@ static void i40e_del_vxlan_port(struct
 net_device *netdev,
 ?	}
 ?}
 
-#endif
 ?static int i40e_get_phys_port_id(struct net_device *netdev,
 ?				?struct netdev_phys_item_id *ppid)

?{

drivers/net/ethernet/intel/i40e/i40e_main.c +0 -2
@@ -8753,10 +8749,8 @@ static const struct net_device_ops
 i40e_netdev_ops = {
 ?	.ndo_get_vf_config	= i40e_ndo_get_vf_config,
 ?	.ndo_set_vf_link_state	= i40e_ndo_set_vf_link_state,
 ?	.ndo_set_vf_spoofchk	= i40e_ndo_set_vf_spoofchk,
-#if IS_ENABLED(CONFIG_VXLAN)
 ?	.ndo_add_vxlan_port	= i40e_add_vxlan_port,
 ?	.ndo_del_vxlan_port	= i40e_del_vxlan_port,
-#endif
 ?	.ndo_get_phys_port_id	= i40e_get_phys_port_id,
 ?	.ndo_fdb_add		= i40e_ndo_fdb_add,

? .ndo_features_check = i40e_features_check,

#12 lore raw

PATCH v4 1/6 i40e: Remove CONFIG_I40E_VXLAN

Ok. That should work, but a quick check would be helpful.

Regards,
Jake

Quoted 163 lines · Anjali

Jake this patch doesn't change the use of CONFIG_VXLAN in our driver to guard against a potential issue that you pointed out. Our driver had already changed to using CONFIG_VXLAN in a previous patch.

But I believe that we will still be okay in the scenario that VXLAN module is not loaded because of two reasons
1) We check a flag in sync_vsi_filters if a filter was added or deleted before proceeding to do anything and that will return very quickly from the function when VXLAN or GENEVE module is not loaded.
2) udp_offload_get_port function has empty definitions in the base kernel that will always exist even when the module is not loaded.

Having said that, I am still going to make sure that it's not an issue with a previous patch for our driver. Although the shift to using udp_offload_get_port with this patch series will help alleviate that issue.

Anjali

Quoted 143 lines

-----Original Message-----
From: Keller, Jacob E
Sent: Tuesday, November 10, 2015 10:01 AM
To: intel-wired-lan at lists.osuosl.org; Singhai, Anjali
Subject: Re: [Intel-wired-lan] [PATCH v4 1/6] i40e: Remove CONFIG_I40E_VXLAN

Hi Anjali,

Quoted 40 lines · Anjali Singhai Jain

If the kernel flag CONFIG_VXLAN is true or CONFIG_VXLAN_MODULE is true, enable VXLAN offload in the driver.

v2: Fix bisection error for this patch series.

---
?drivers/net/ethernet/intel/i40e/i40e.h??????|??2 -- ?drivers/net/ethernet/intel/i40e/i40e_main.c | 10 ++-------- ?2 files changed, 2 insertions(+), 10 deletions(-)

drivers/net/ethernet/intel/i40e/i40e.h +0 -2
index 8ed759e..6c4d154 100644
@@ -282,11 +282,9 @@ struct i40e_pf {
 ?	u32 fd_atr_cnt;
 ?	u32 fd_tcp_rule;
 
-#if IS_ENABLED(CONFIG_VXLAN)
 ?	__be16??vxlan_ports[I40E_MAX_PF_UDP_OFFLOAD_PORTS];
 ?	u16 pending_vxlan_bitmap;
 
-#endif
 ?	enum i40e_interrupt_policy int_policy;
 ?	u16 rx_itr_default;
 ?	u16 tx_itr_default;
drivers/net/ethernet/intel/i40e/i40e_main.c +0 -1
index b447af6..0235a8a 100644
@@ -6990,13 +6990,13 @@ static void i40e_handle_mdd_event(struct
 i40e_pf *pf)
 ?	i40e_flush(hw);
 ?}
 
-#if IS_ENABLED(CONFIG_VXLAN)
Quoted 8 lines

?/**
? * i40e_sync_vxlan_filters_subtask - Sync the VSI filter list with HW
? * @pf: board private structure
? **/
?static void i40e_sync_vxlan_filters_subtask(struct i40e_pf *pf) ?{
+#if IS_ENABLED(CONFIG_VXLAN)

Direct use of CONFIG_VXLAN is not going to work. What happens in the case
where CONFIG_VXLAN=m and CONFIG_I40E=y?

The kernel will load i40e as it loads itself at boot and vxlan module will not get
included (because i40e isn't a module so it doesn't run depmod etc) and then
it will run and try to call vxlan code and fail because of an unknown symbol
since vxlan won't have been started yet.

This is the entire reason why CONFIG_XXX_VXLAN exists. The alternative is
to use select VXLAN and force VXLAN on when we enable I40E.

That's the primary reason why we can't directly use CONFIG_VXLAN as a
check in driver code.

Regards,
Jake

Quoted 61 lines

? struct i40e_hw *hw = &pf->hw;
? i40e_status ret;
? __be16 port;

drivers/net/ethernet/intel/i40e/i40e_main.c +1 -1
@@ -7030,9 +7030,9 @@ static void
 i40e_sync_vxlan_filters_subtask(struct i40e_pf *pf)
 ?			}
 ?		}
 ?	}
+#endif
 ?}
 
-#endif

?/**
? * i40e_service_task - Run the driver's async subtasks ? * @work: pointer to work_struct containing our data @@ -7057,9 +7057,7 @@ static void i40e_service_task(struct work_struct *work)
? i40e_watchdog_subtask(pf);
? i40e_fdir_reinit_subtask(pf);
? i40e_sync_filters_subtask(pf);
-#if IS_ENABLED(CONFIG_VXLAN)
? i40e_sync_vxlan_filters_subtask(pf);
-#endif
? i40e_clean_adminq_subtask(pf);

? i40e_service_event_complete(pf);

drivers/net/ethernet/intel/i40e/i40e_main.c +0 -0
@@ -8433,7 +8431,6 @@ static int i40e_set_features(struct

net_device
*netdev,
? return 0;
?}

-#if IS_ENABLED(CONFIG_VXLAN)
?/**
? * i40e_get_vxlan_port_idx - Lookup a possibly offloaded for Rx UDP
port
? * @pf: board private structure

drivers/net/ethernet/intel/i40e/i40e_main.c +0 -1
@@ -8528,7 +8525,6 @@ static void i40e_del_vxlan_port(struct
 net_device *netdev,
 ?	}
 ?}
 
-#endif
 ?static int i40e_get_phys_port_id(struct net_device *netdev,

? ?struct netdev_phys_item_id
*ppid)
?{

drivers/net/ethernet/intel/i40e/i40e_main.c +0 -0
@@ -8753,10 +8749,8 @@ static const struct net_device_ops
 i40e_netdev_ops = {
 ?	.ndo_get_vf_config	= i40e_ndo_get_vf_config,

? .ndo_set_vf_link_state =
i40e_ndo_set_vf_link_state,
? .ndo_set_vf_spoofchk = i40e_ndo_set_vf_spoofchk,
-#if IS_ENABLED(CONFIG_VXLAN)
? .ndo_add_vxlan_port = i40e_add_vxlan_port,
? .ndo_del_vxlan_port = i40e_del_vxlan_port,
-#endif
? .ndo_get_phys_port_id = i40e_get_phys_port_id,
? .ndo_fdb_add = i40e_ndo_fdb_add,
? .ndo_features_check = i40e_features_check,

#13 lore raw

PATCH v4 1/6 i40e: Remove CONFIG_I40E_VXLAN

Ok, So I did do a check. This series does fix the issue where we no more have to worry about whether VXLAN or GENEVE is a module and the driver is in-built since udp_offload_get_port will always be defined.. But we will have to actually drop the previous patch that changes the driver to start using CONFIG_VXLAN, and rebase this patch series.

I will go ahead and do that.

Anjali

Quoted 169 lines

-----Original Message-----
From: Keller, Jacob E
Sent: Tuesday, November 10, 2015 11:23 AM
To: intel-wired-lan at lists.osuosl.org; Singhai, Anjali
Subject: Re: [Intel-wired-lan] [PATCH v4 1/6] i40e: Remove CONFIG_I40E_VXLAN

Ok. That should work, but a quick check would be helpful.

Regards,
Jake

Quoted 156 lines · Anjali

Jake this patch doesn't change the use of CONFIG_VXLAN in our driver to guard against a potential issue that you pointed out. Our driver had already changed to using CONFIG_VXLAN in a previous patch.

But I believe that we will still be okay in the scenario that VXLAN module is not loaded because of two reasons
1) We check a flag in sync_vsi_filters if a filter was added or deleted before proceeding to do anything and that will return very quickly from the function when VXLAN or GENEVE module is not loaded.
2) udp_offload_get_port function has empty definitions in the base kernel that will always exist even when the module is not loaded.

Having said that, I am still going to make sure that it's not an issue with a previous patch for our driver. Although the shift to using udp_offload_get_port with this patch series will help alleviate that issue.

Anjali

Quoted 136 lines

-----Original Message-----
From: Keller, Jacob E
Sent: Tuesday, November 10, 2015 10:01 AM
To: intel-wired-lan at lists.osuosl.org; Singhai, Anjali
Subject: Re: [Intel-wired-lan] [PATCH v4 1/6] i40e: Remove CONFIG_I40E_VXLAN

Hi Anjali,

Quoted 40 lines · Anjali Singhai Jain

If the kernel flag CONFIG_VXLAN is true or CONFIG_VXLAN_MODULE is true, enable VXLAN offload in the driver.

v2: Fix bisection error for this patch series.

---
?drivers/net/ethernet/intel/i40e/i40e.h??????|??2 -- ?drivers/net/ethernet/intel/i40e/i40e_main.c | 10 ++-------- ?2 files changed, 2 insertions(+), 10 deletions(-)

drivers/net/ethernet/intel/i40e/i40e.h +0 -2
index 8ed759e..6c4d154 100644
@@ -282,11 +282,9 @@ struct i40e_pf {
 ?	u32 fd_atr_cnt;
 ?	u32 fd_tcp_rule;
 
-#if IS_ENABLED(CONFIG_VXLAN)
 ?	__be16??vxlan_ports[I40E_MAX_PF_UDP_OFFLOAD_PORTS];
 ?	u16 pending_vxlan_bitmap;
 
-#endif
 ?	enum i40e_interrupt_policy int_policy;
 ?	u16 rx_itr_default;
 ?	u16 tx_itr_default;
drivers/net/ethernet/intel/i40e/i40e_main.c +0 -1
index b447af6..0235a8a 100644
@@ -6990,13 +6990,13 @@ static void i40e_handle_mdd_event(struct
 i40e_pf *pf)
 ?	i40e_flush(hw);
 ?}
 
-#if IS_ENABLED(CONFIG_VXLAN)
Quoted 8 lines

?/**
? * i40e_sync_vxlan_filters_subtask - Sync the VSI filter list with HW
? * @pf: board private structure
? **/
?static void i40e_sync_vxlan_filters_subtask(struct i40e_pf *pf) ?{
+#if IS_ENABLED(CONFIG_VXLAN)

Direct use of CONFIG_VXLAN is not going to work. What happens in the case where CONFIG_VXLAN=m and CONFIG_I40E=y?

The kernel will load i40e as it loads itself at boot and vxlan module will not get included (because i40e isn't a module so it doesn't run depmod etc) and then it will run and try to call vxlan code and fail because of an unknown symbol since vxlan won't have been started yet.

This is the entire reason why CONFIG_XXX_VXLAN exists. The alternative is to use select VXLAN and force VXLAN on when we enable I40E.

That's the primary reason why we can't directly use CONFIG_VXLAN as a check in driver code.

Regards,
Jake

Quoted 58 lines

? struct i40e_hw *hw = &pf->hw;
? i40e_status ret;
? __be16 port;

drivers/net/ethernet/intel/i40e/i40e_main.c +1 -1
@@ -7030,9 +7030,9 @@ static void
 i40e_sync_vxlan_filters_subtask(struct i40e_pf *pf)
 ?			}
 ?		}
 ?	}
+#endif
 ?}
 
-#endif

?/**
? * i40e_service_task - Run the driver's async subtasks ? * @work: pointer to work_struct containing our data @@ -7057,9 +7057,7 @@ static void i40e_service_task(struct work_struct *work)
? i40e_watchdog_subtask(pf);
? i40e_fdir_reinit_subtask(pf);
? i40e_sync_filters_subtask(pf);
-#if IS_ENABLED(CONFIG_VXLAN)
? i40e_sync_vxlan_filters_subtask(pf);
-#endif
? i40e_clean_adminq_subtask(pf);

? i40e_service_event_complete(pf); @@ -8433,7 +8431,6 @@ static
int i40e_set_features(struct net_device *netdev,
? return 0;
?}

-#if IS_ENABLED(CONFIG_VXLAN)
?/**
? * i40e_get_vxlan_port_idx - Lookup a possibly offloaded for Rx UDP port
? * @pf: board private structure

drivers/net/ethernet/intel/i40e/i40e_main.c +0 -1
@@ -8528,7 +8525,6 @@ static void i40e_del_vxlan_port(struct
 net_device *netdev,
 ?	}
 ?}
 
-#endif
 ?static int i40e_get_phys_port_id(struct net_device *netdev,

? ?struct netdev_phys_item_id
*ppid)
?{

drivers/net/ethernet/intel/i40e/i40e_main.c +0 -0
@@ -8753,10 +8749,8 @@ static const struct net_device_ops
 i40e_netdev_ops = {
 ?	.ndo_get_vf_config	= i40e_ndo_get_vf_config,

? .ndo_set_vf_link_state =
i40e_ndo_set_vf_link_state,
? .ndo_set_vf_spoofchk = i40e_ndo_set_vf_spoofchk,
-#if IS_ENABLED(CONFIG_VXLAN)
? .ndo_add_vxlan_port = i40e_add_vxlan_port,
? .ndo_del_vxlan_port = i40e_del_vxlan_port,
-#endif
? .ndo_get_phys_port_id = i40e_get_phys_port_id,
? .ndo_fdb_add = i40e_ndo_fdb_add,
? .ndo_features_check = i40e_features_check,

#14 lore raw

PATCH v4 1/6 i40e: Remove CONFIG_I40E_VXLAN

In reply to Anjali Singhai Jain
Quoted 10 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On Behalf Of Anjali Singhai Jain
Sent: Tuesday, November 10, 2015 9:57 AM
To: intel-wired-lan at lists.osuosl.org
Subject: [Intel-wired-lan] [PATCH v4 1/6] i40e: Remove CONFIG_I40E_VXLAN

If the kernel flag CONFIG_VXLAN is true or CONFIG_VXLAN_MODULE is true, enable VXLAN offload in the driver.

Quoted 8 lines

v2: Fix bisection error for this patch series.

---
 drivers/net/ethernet/intel/i40e/i40e.h      |  2 --
 drivers/net/ethernet/intel/i40e/i40e_main.c | 10 ++--------
 2 files changed, 2 insertions(+), 10 deletions(-)

Patch code changes altered by subesquent patch

#15 lore raw

PATCH v4 1/6 i40e: Remove CONFIG_I40E_VXLAN

In reply to Anjali Singhai Jain
Quoted 10 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On Behalf Of Anjali Singhai Jain
Sent: Tuesday, November 10, 2015 9:57 AM
To: intel-wired-lan at lists.osuosl.org
Subject: [Intel-wired-lan] [PATCH v4 1/6] i40e: Remove CONFIG_I40E_VXLAN

If the kernel flag CONFIG_VXLAN is true or CONFIG_VXLAN_MODULE is true, enable VXLAN offload in the driver.

Quoted 8 lines

v2: Fix bisection error for this patch series.

---
 drivers/net/ethernet/intel/i40e/i40e.h      |  2 --
 drivers/net/ethernet/intel/i40e/i40e_main.c | 10 ++--------
 2 files changed, 2 insertions(+), 10 deletions(-)