MIPS: ath79: skip pbl lowlevel init if running from RAM
v2 cover MIPS: ath79: skip pbl lowlevel init if running from RAM
Changes since v1:
* fix commit messages (thanks to Dmitry Smagin);
* assume that tplink-mr3020's ROM start address is 0xbf000000;
* add 'Tested-by: Yegor Yefremov <[email protected]>'.
Antony Pavlov (2):
MIPS: black-swift: skip pbl lowlevel init if running from RAM
MIPS: tplink-mr3020: skip pbl lowlevel init if running from RAM
Oleksij Rempel (1):
MIPS: pbl: add pbl_blt macro
arch/mips/boards/black-swift/include/board/board_pbl_start.h | 3 +++ .../boards/tplink-mr3020/include/board/board_pbl_start.h | 3 +++ arch/mips/include/asm/pbl_macros.h | 12 ++++++++++++ 3 files changed, 18 insertions(+)
Signature · 7 lines
2.6.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH v2 1/3 MIPS: pbl: add pbl_blt macro
From: Oleksij Rempel <[email protected]>
Barebox' PBL is able to initialize SoC's memory controller, but it can be used only if PBL runs from ROM or on-chip SRAM. MIPS architecture standard boot vector is 0xbfc00000
so on most MIPS SoCs all addresses higher than 0xbfc00000 belong to boot ROM or on-chip SRAM. Thus there's a
simple criterion to check if PBL runs from ROM: just
check if current PC is higher than 0xbfc00000.
Some MIPS boards have ROM start address lower than 0xbfc00000 so it's reasonable to make ROM start address checking board-dependant.
The pbl_blt macro checks if current pc is lower than the first argument (ROM start address). If so then next instruction executed is defined by the second argument of the macro.
--- arch/mips/include/asm/pbl_macros.h | 12 ++++++++++++ 1 file changed, 12 insertions(+)
arch/mips/include/asm/pbl_macros.h +12 -0
@@ -60,6 +60,18 @@ .set pop .endm + .macro pbl_blt addr label tmp + .set push + .set noreorder + move \tmp, ra # preserve ra beforehand + bal 253f + nop +253: + bltu ra, \addr, \label + move ra, \tmp # restore ra + .set pop + .endm + .macro pbl_sleep reg count .set push .set noreorder
Signature · 7 lines
2.6.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH v2 2/3 MIPS: black-swift: skip pbl lowlevel init if running from RAM
In reply to Antony PavlovBlack Swift has 16 MiB flash boot ROM. The standard board's bootloader (U-Boot_mod) remaps boot ROM to 0xbf000000.
--- arch/mips/boards/black-swift/include/board/board_pbl_start.h | 3 +++ 1 file changed, 3 insertions(+)
arch/mips/boards/black-swift/include/board/board_pbl_start.h +3 -0
@@ -28,9 +28,12 @@mips_disable_interrupts + pbl_blt 0xbf000000 skip_pll_ram_config t8 + pbl_ar9331_pll pbl_ar9331_ddr2_config +skip_pll_ram_config: pbl_ar9331_uart_enable debug_ll_ar9331_init mips_nmon
Signature · 7 lines
2.6.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH v2 3/3 MIPS: tplink-mr3020: skip pbl lowlevel init if running from RAM
In reply to Antony PavlovTP-Link MR3020 has 4 MiB flash boot ROM.
Usually boot ROM is mapped to 0xbfc00000. However, as AR9331 allows to remap boot ROM to 0xbf000000 it's better to assume that boot ROM starts at 0xbf000000.
--- arch/mips/boards/tplink-mr3020/include/board/board_pbl_start.h | 3 +++ 1 file changed, 3 insertions(+)
arch/mips/boards/tplink-mr3020/include/board/board_pbl_start.h +3 -0
@@ -28,9 +28,12 @@mips_disable_interrupts + pbl_blt 0xbf000000 skip_pll_ram_config t8 + pbl_ar9331_pll pbl_ar9331_ddr1_config +skip_pll_ram_config: pbl_ar9331_uart_enable debug_ll_ar9331_init mips_nmon
Signature · 7 lines
2.6.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Sascha Hauer
AppliedQuoted 10 lines · Antony Pavlov
Changes since v1:
* fix commit messages (thanks to Dmitry Smagin);
* assume that tplink-mr3020's ROM start address is0xbf000000;
* add 'Tested-by: Yegor Yefremov <[email protected]>'.Antony Pavlov (2):
MIPS: black-swift: skip pbl lowlevel init if running from RAM
MIPS: tplink-mr3020: skip pbl lowlevel init if running from RAM
Quoted 7 lines
Oleksij Rempel (1):
MIPS: pbl: addpbl_bltmacroarch/mips/boards/black-swift/include/board/board_pbl_start.h | 3 +++ .../boards/tplink-mr3020/include/board/board_pbl_start.h | 3 +++ arch/mips/include/asm/pbl_macros.h | 12 ++++++++++++ 3 files changed, 18 insertions(+)
Applied, thanks
Sascha
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox