Skip to contentSkip to conversation

Fix typo: firstly -> first.

PATCH In review Vagrant Cascadian 3 participants 3 messages Nov 24, 2015 – Dec 6, 2015

Subsystems (3)
Block layer Memory technology devices (MTD) NAND flash
lore
Share & tools
lore

Vagrant Cascadian

author
#0 lore raw

PATCH 1/1 Fix typo: firstly -> first.

Signed-off-by Vagrant Cascadian <[email protected]>

---

 drivers/block/ahci.c           | 4 ++--
 drivers/mtd/nand/pxa3xx_nand.c | 2 +-
 drivers/serial/serial.c        | 2 +-
 3 files changed, 4 insertions(+), 4 deletions(-)
drivers/block/ahci.c +2 -2
index 734fdcc..5efa821 100644
@@ -818,7 +818,7 @@ static int ata_scsiop_read_capacity10(ccb *pccb)
 	if (!ataid[pccb->target]) {
 		printf("scsi_ahci: SCSI READ CAPACITY10 command failure. "
 		       "\tNo ATA info!\n"
-		       "\tPlease run SCSI command INQUIRY firstly!\n");
+		       "\tPlease run SCSI command INQUIRY first!\n");
 		return -EPERM;
 	}
 

@@ -847,7 +847,7 @@ static int ata_scsiop_read_capacity16(ccb *pccb)
 	if (!ataid[pccb->target]) {
 		printf("scsi_ahci: SCSI READ CAPACITY16 command failure. "
 		       "\tNo ATA info!\n"
-		       "\tPlease run SCSI command INQUIRY firstly!\n");
+		       "\tPlease run SCSI command INQUIRY first!\n");
 		return -EPERM;
 	}
drivers/mtd/nand/pxa3xx_nand.c +1 -1
index 1565a9a..f65b499 100644
@@ -451,7 +451,7 @@ static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info,
 }
 
 /**
- * NOTE: it is a must to set ND_RUN firstly, then write
+ * NOTE: it is a must to set ND_RUN first, then write
  * command buffer, otherwise, it does not work.
  * We enable all the interrupt at the same time, and
  * let pxa3xx_nand_irq to handle all logic.
drivers/serial/serial.c +1 -1
index 422d3ae..f1bd15b 100644
@@ -527,7 +527,7 @@ static const int bauds[] = CONFIG_SYS_BAUDRATE_TABLE;
  *
  * Do a loopback test of the currently selected serial port. This
  * function is only useful in the context of the POST testing framwork.
- * The serial port is firstly configured into loopback mode and then
+ * The serial port is first configured into loopback mode and then
  * characters are sent through it.
  *
  * Returns 0 on success, value otherwise.
Signature · 1 line
2.1.4
#2 lore raw
In reply to Vagrant Cascadian
Quoted 2 lines · Vagrant Cascadian
Signed-off-by Vagrant Cascadian <[email protected]>
Acked-by Marek Vasut <[email protected]>

Applied to u-boot/master, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20151206/32040be8/attachment.sig>