Skip to contentSkip to conversation

xhci: Fix memory leak in xhci_pme_acpi_rtd3_enable()

PATCH New Mathias Nyman 1 participant 2 messages Dec 4, 2015 1 message not in the archive

Subsystems (3)
lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

#1 lore raw

PATCH 1/2 xhci: Fix memory leak in xhci_pme_acpi_rtd3_enable()

From: Mika Westerberg <[email protected]>

There is a memory leak because acpi_evaluate_dsm() actually returns an object which the caller is supposed to release. Fix this by calling ACPI_FREE() for the returned object (this expands to kfree() so passing NULL there is fine as well).

While there correct indentation in !CONFIG_ACPI case.

---
 drivers/usb/host/xhci-pci.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)
drivers/usb/host/xhci-pci.c +6 -2
index 17f6897..c621090 100644
@@ -188,10 +188,14 @@ static void xhci_pme_acpi_rtd3_enable(struct pci_dev *dev)
 		0xb7, 0x0c, 0x34, 0xac,	0x01, 0xe9, 0xbf, 0x45,
 		0xb7, 0xe6, 0x2b, 0x34, 0xec, 0x93, 0x1e, 0x23,
 	};
-	acpi_evaluate_dsm(ACPI_HANDLE(&dev->dev), intel_dsm_uuid, 3, 1, NULL);
+	union acpi_object *obj;
+
+	obj = acpi_evaluate_dsm(ACPI_HANDLE(&dev->dev), intel_dsm_uuid, 3, 1,
+				NULL);
+	ACPI_FREE(obj);
 }
 #else
-	static void xhci_pme_acpi_rtd3_enable(struct pci_dev *dev) { }
+static void xhci_pme_acpi_rtd3_enable(struct pci_dev *dev) { }
 #endif /* CONFIG_ACPI */
 
 /* called during probe() after chip reset completes */
Signature · 1 line
1.9.1
#2 lore raw

PATCH 2/2 usb: xhci: fix config fail of FS hub behind a HS hub with MTT

In reply to a message not in the archive

From: Chunfeng Yun <[email protected]>

if a full speed hub connects to a high speed hub which supports MTT, the MTT field of its slot context will be set to 1 when xHCI driver setups an xHCI virtual device in xhci_setup_addressable_virt_dev(); once usb core fetch its hub descriptor, and need to update the xHC's internal data structures for the device, the HUB field of its slot context will be set to 1 too, meanwhile MTT is also set before, this will cause configure endpoint command fail, so in the case, we should clear MTT to 0 for full speed hub according to section 6.2.2

---
 drivers/usb/host/xhci.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/usb/host/xhci.c +8 -0
index dfa44d3..3f91270 100644
@@ -4778,8 +4778,16 @@ int xhci_update_hub_device(struct usb_hcd *hcd, struct usb_device *hdev,
 	ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG);
 	slot_ctx = xhci_get_slot_ctx(xhci, config_cmd->in_ctx);
 	slot_ctx->dev_info |= cpu_to_le32(DEV_HUB);
+	/*
+	 * refer to section 6.2.2: MTT should be 0 for full speed hub,
+	 * but it may be already set to 1 when setup an xHCI virtual
+	 * device, so clear it anyway.
+	 */
 	if (tt->multi)
 		slot_ctx->dev_info |= cpu_to_le32(DEV_MTT);
+	else if (hdev->speed == USB_SPEED_FULL)
+		slot_ctx->dev_info &= cpu_to_le32(~DEV_MTT);
+
 	if (xhci->hci_version > 0x95) {
 		xhci_dbg(xhci, "xHCI version %x needs hub "
 				"TT think time and number of ports\n",
Signature · 1 line
1.9.1