drm/i915: Correct max delay for HDMI hotplug live status checking
Subsystems (2)
PATCH 1/1 drm/i915: Correct max delay for HDMI hotplug live status checking
The total delay of HDMI hotplug detecting with 30ms should have been split into a resolution of 3 retries of 10ms each, for the worst cases. But it still suffered from only waiting 10ms at most in intel_hdmi_detect(). This patch corrects it by reading hotplug status with 4 times at most for 30ms delay.
--- drivers/gpu/drm/i915/intel_hdmi.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) mode change 100644 => 100755 drivers/gpu/drm/i915/intel_hdmi.c
drivers/gpu/drm/i915/intel_hdmi.c +5 -2
@@ -1387,16 +1387,19 @@ intel_hdmi_detect(struct drm_connector *connector, bool force)struct intel_hdmi *intel_hdmi =intel_attached_hdmi (connector);struct drm_i915_private *dev_priv =to_i915 (connector->dev);bool live_status = false; -unsigned int retry =3 ; +// read hotplug status 4 times at most for 30ms delay (3 retries of 10ms each) +unsigned int retry =4 ;DRM_DEBUG_KMS ("[CONNECTOR:%d:%s]\n" , connector->base.id, connector->name);intel_display_power_get (dev_priv,POWER_DOMAIN_GMBUS ); -while (!live_status && --retry) { +while (!live_status && retry--) { live_status =intel_digital_port_connected (dev_priv,hdmi_to_dig_port (intel_hdmi)); +if (live_status || !retry) +break ;mdelay (10 ); }
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
How about following instead of two levels of check in the while loop:
unsigned int retry = 3;
do {
live_status = intel_digital_port_connected(dev_priv,
hdmi_to_dig_port(intel_hdmi));
if (live_status)
break;
mdelay(10);
} while (--retry);Regards,
Sonika
-----Original Message-----
From: Intel-gfx [mailto:[email protected]] On Behalf Of Wang, Gary C
Sent: Friday, December 11, 2015 7:39 AM
To: [email protected]
Subject: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
The total delay of HDMI hotplug detecting with 30ms should have been split into a resolution of 3 retries of 10ms each, for the worst cases. But it still suffered from only waiting 10ms at most in intel_hdmi_detect(). This patch corrects it by reading hotplug status with 4 times at most for 30ms delay.
--- drivers/gpu/drm/i915/intel_hdmi.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) mode change 100644 => 100755 drivers/gpu/drm/i915/intel_hdmi.c
drivers/gpu/drm/i915/intel_hdmi.c +5 -2
@@ -1387,16 +1387,19 @@ intel_hdmi_detect(struct drm_connector *connector, bool force)struct intel_hdmi *intel_hdmi =intel_attached_hdmi (connector);struct drm_i915_private *dev_priv =to_i915 (connector->dev);bool live_status = false; -unsigned int retry =3 ; +// read hotplug status 4 times at most for 30ms delay (3 retries of 10ms each) +unsigned int retry =4 ;DRM_DEBUG_KMS ("[CONNECTOR:%d:%s]\n" , connector->base.id, connector->name);intel_display_power_get (dev_priv,POWER_DOMAIN_GMBUS ); -while (!live_status && --retry) { +while (!live_status && retry--) { live_status =intel_digital_port_connected (dev_priv,hdmi_to_dig_port (intel_hdmi)); +if (live_status || !retry) +break ;mdelay (10 ); }
--
1.9.1
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Wang, Gary C
Reviewed-by Cooper ChiouHi Sonika,
Thanks for your comment, and it's more readability on code.
But it only delay 2 integration of each 10ms among checking hot-plug with 3 times. Could I change it to following snippet code to read hotplug_status 4 times at most for 3 integration 10ms delay?
unsigned int retry = 3;
do {
live_status = intel_digital_port_connected(dev_priv,
hdmi_to_dig_port(intel_hdmi));
if (live_status || !retry)
break;
mdelay(10);
} while (retry--);Thanks!
Gary
-----Original Message-----
From: Jindal, Sonika
Sent: Friday, December 11, 2015 1:05 PM
To: Wang, Gary C <[email protected]>; [email protected]
Subject: RE: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
How about following instead of two levels of check in the while loop:
unsigned int retry = 3;
do {
live_status = intel_digital_port_connected(dev_priv,
hdmi_to_dig_port(intel_hdmi));
if (live_status)
break;
mdelay(10);
} while (--retry);Regards,
Sonika
-----Original Message-----
From: Intel-gfx [mailto:[email protected]] On Behalf Of Wang, Gary C
Sent: Friday, December 11, 2015 7:39 AM
To: [email protected]
Subject: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
The total delay of HDMI hotplug detecting with 30ms should have been split into a resolution of 3 retries of 10ms each, for the worst cases. But it still suffered from only waiting 10ms at most in intel_hdmi_detect(). This patch corrects it by reading hotplug status with 4 times at most for 30ms delay.
--- drivers/gpu/drm/i915/intel_hdmi.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) mode change 100644 => 100755 drivers/gpu/drm/i915/intel_hdmi.c
drivers/gpu/drm/i915/intel_hdmi.c +5 -2
@@ -1387,16 +1387,19 @@ intel_hdmi_detect(struct drm_connector *connector, bool force)struct intel_hdmi *intel_hdmi =intel_attached_hdmi (connector);struct drm_i915_private *dev_priv =to_i915 (connector->dev);bool live_status = false; -unsigned int retry =3 ; +// read hotplug status 4 times at most for 30ms delay (3 retries of 10ms each) +unsigned int retry =4 ;DRM_DEBUG_KMS ("[CONNECTOR:%d:%s]\n" , connector->base.id, connector->name);intel_display_power_get (dev_priv,POWER_DOMAIN_GMBUS ); -while (!live_status && --retry) { +while (!live_status && retry--) { live_status =intel_digital_port_connected (dev_priv,hdmi_to_dig_port (intel_hdmi)); +if (live_status || !retry) +break ;mdelay (10 ); }
--
1.9.1
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Jindal, Sonika
Reviewed-by Cooper ChiouSure.
Can you please also post your findings about different panels taking different time to settle the live status so that we know that this increase in retrials is helping you with multiple monitors?
Regards,
Sonika
-----Original Message-----
From: Wang, Gary C
Sent: Friday, December 11, 2015 11:34 AM
To: Jindal, Sonika <[email protected]>; [email protected]
Subject: RE: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
Hi Sonika,
Thanks for your comment, and it's more readability on code.
But it only delay 2 integration of each 10ms among checking hot-plug with 3 times. Could I change it to following snippet code to read hotplug_status 4 times at most for 3 integration 10ms delay?
unsigned int retry = 3;
do {
live_status = intel_digital_port_connected(dev_priv,
hdmi_to_dig_port(intel_hdmi));
if (live_status || !retry)
break;
mdelay(10);
} while (retry--);Thanks!
Gary
-----Original Message-----
From: Jindal, Sonika
Sent: Friday, December 11, 2015 1:05 PM
To: Wang, Gary C <[email protected]>; [email protected]
Subject: RE: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
How about following instead of two levels of check in the while loop:
unsigned int retry = 3;
do {
live_status = intel_digital_port_connected(dev_priv,
hdmi_to_dig_port(intel_hdmi));
if (live_status)
break;
mdelay(10);
} while (--retry);Regards,
Sonika
-----Original Message-----
From: Intel-gfx [mailto:[email protected]] On Behalf Of Wang, Gary C
Sent: Friday, December 11, 2015 7:39 AM
To: [email protected]
Subject: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
The total delay of HDMI hotplug detecting with 30ms should have been split into a resolution of 3 retries of 10ms each, for the worst cases. But it still suffered from only waiting 10ms at most in intel_hdmi_detect(). This patch corrects it by reading hotplug status with 4 times at most for 30ms delay.
--- drivers/gpu/drm/i915/intel_hdmi.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) mode change 100644 => 100755 drivers/gpu/drm/i915/intel_hdmi.c
drivers/gpu/drm/i915/intel_hdmi.c +5 -2
@@ -1387,16 +1387,19 @@ intel_hdmi_detect(struct drm_connector *connector, bool force)struct intel_hdmi *intel_hdmi =intel_attached_hdmi (connector);struct drm_i915_private *dev_priv =to_i915 (connector->dev);bool live_status = false; -unsigned int retry =3 ; +// read hotplug status 4 times at most for 30ms delay (3 retries of 10ms each) +unsigned int retry =4 ;DRM_DEBUG_KMS ("[CONNECTOR:%d:%s]\n" , connector->base.id, connector->name);intel_display_power_get (dev_priv,POWER_DOMAIN_GMBUS ); -while (!live_status && --retry) { +while (!live_status && retry--) { live_status =intel_digital_port_connected (dev_priv,hdmi_to_dig_port (intel_hdmi)); +if (live_status || !retry) +break ;mdelay (10 ); }
--
1.9.1
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Wang, Gary C
Reviewed-by Cooper ChiouNo problem.
Please refer following information.
Lenovo Mode: L246 1xwA (4/30 failed, necessary hot-plug delay: 58/40/60/40ms) Philips Model : HH2AP (9/30 failed, necessary hot-plug delay: 80/50/50/60/46/40/58/58/39ms) BENQ Model:ET-0035-N (6/30 failed, necessary hot-plug delay: 60/50/50/80/80/40ms) DELL Model:U2713HM (2/30 failed, necessary hot-plug delay: 58/59ms)
HP Model: HP-LP2475w (5/30 failed, necessary hot-plug delay: 70/50/40/60/40ms)
Those test were based on following test-case (test continually with 30 test cycles),
1. HDMI display correctly
2. Un-plug/re-plug HDMI cable
3. Wait for one sec
Thanks for your review!
Gary
-----Original Message-----
From: Jindal, Sonika
Sent: Friday, December 11, 2015 2:18 PM
To: Wang, Gary C <[email protected]>; [email protected]
Subject: RE: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
Sure.
Can you please also post your findings about different panels taking different time to settle the live status so that we know that this increase in retrials is helping you with multiple monitors?
Regards,
Sonika
-----Original Message-----
From: Wang, Gary C
Sent: Friday, December 11, 2015 11:34 AM
To: Jindal, Sonika <[email protected]>; [email protected]
Subject: RE: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
Hi Sonika,
Thanks for your comment, and it's more readability on code.
But it only delay 2 integration of each 10ms among checking hot-plug with 3 times. Could I change it to following snippet code to read hotplug_status 4 times at most for 3 integration 10ms delay?
unsigned int retry = 3;
do {
live_status = intel_digital_port_connected(dev_priv,
hdmi_to_dig_port(intel_hdmi));
if (live_status || !retry)
break;
mdelay(10);
} while (retry--);Thanks!
Gary
-----Original Message-----
From: Jindal, Sonika
Sent: Friday, December 11, 2015 1:05 PM
To: Wang, Gary C <[email protected]>; [email protected]
Subject: RE: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
How about following instead of two levels of check in the while loop:
unsigned int retry = 3;
do {
live_status = intel_digital_port_connected(dev_priv,
hdmi_to_dig_port(intel_hdmi));
if (live_status)
break;
mdelay(10);
} while (--retry);Regards,
Sonika
-----Original Message-----
From: Intel-gfx [mailto:[email protected]] On Behalf Of Wang, Gary C
Sent: Friday, December 11, 2015 7:39 AM
To: [email protected]
Subject: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
The total delay of HDMI hotplug detecting with 30ms should have been split into a resolution of 3 retries of 10ms each, for the worst cases. But it still suffered from only waiting 10ms at most in intel_hdmi_detect(). This patch corrects it by reading hotplug status with 4 times at most for 30ms delay.
--- drivers/gpu/drm/i915/intel_hdmi.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) mode change 100644 => 100755 drivers/gpu/drm/i915/intel_hdmi.c
drivers/gpu/drm/i915/intel_hdmi.c +5 -2
@@ -1387,16 +1387,19 @@ intel_hdmi_detect(struct drm_connector *connector, bool force)struct intel_hdmi *intel_hdmi =intel_attached_hdmi (connector);struct drm_i915_private *dev_priv =to_i915 (connector->dev);bool live_status = false; -unsigned int retry =3 ; +// read hotplug status 4 times at most for 30ms delay (3 retries of 10ms each) +unsigned int retry =4 ;DRM_DEBUG_KMS ("[CONNECTOR:%d:%s]\n" , connector->base.id, connector->name);intel_display_power_get (dev_priv,POWER_DOMAIN_GMBUS ); -while (!live_status && --retry) { +while (!live_status && retry--) { live_status =intel_digital_port_connected (dev_priv,hdmi_to_dig_port (intel_hdmi)); +if (live_status || !retry) +break ;mdelay (10 ); }
--
1.9.1
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Wang, Gary C
Reviewed-by Cooper ChiouI will upload new version of patch for review. Thanks!
-----Original Message-----
From: Intel-gfx [mailto:[email protected]] On Behalf Of Wang, Gary C
Sent: Friday, December 11, 2015 2:23 PM
To: Jindal, Sonika <[email protected]>; [email protected]
Subject: Re: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
No problem.
Please refer following information.
Lenovo Mode: L246 1xwA (4/30 failed, necessary hot-plug delay: 58/40/60/40ms) Philips Model : HH2AP (9/30 failed, necessary hot-plug delay: 80/50/50/60/46/40/58/58/39ms) BENQ Model:ET-0035-N (6/30 failed, necessary hot-plug delay: 60/50/50/80/80/40ms) DELL Model:U2713HM (2/30 failed, necessary hot-plug delay: 58/59ms) HP Model: HP-LP2475w (5/30 failed, necessary hot-plug delay: 70/50/40/60/40ms)
Those test were based on following test-case (test continually with 30 test cycles), 1. HDMI display correctly 2. Un-plug/re-plug HDMI cable 3. Wait for one sec
Thanks for your review!
Gary
-----Original Message-----
From: Jindal, Sonika
Sent: Friday, December 11, 2015 2:18 PM
To: Wang, Gary C <[email protected]>; [email protected]
Subject: RE: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
Sure.
Can you please also post your findings about different panels taking different time to settle the live status so that we know that this increase in retrials is helping you with multiple monitors?
Regards,
Sonika
-----Original Message-----
From: Wang, Gary C
Sent: Friday, December 11, 2015 11:34 AM
To: Jindal, Sonika <[email protected]>; [email protected]
Subject: RE: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
Hi Sonika,
Thanks for your comment, and it's more readability on code.
But it only delay 2 integration of each 10ms among checking hot-plug with 3 times. Could I change it to following snippet code to read hotplug_status 4 times at most for 3 integration 10ms delay?
unsigned int retry = 3;
do {
live_status = intel_digital_port_connected(dev_priv,
hdmi_to_dig_port(intel_hdmi));
if (live_status || !retry)
break;
mdelay(10);
} while (retry--);Thanks!
Gary
-----Original Message-----
From: Jindal, Sonika
Sent: Friday, December 11, 2015 1:05 PM
To: Wang, Gary C <[email protected]>; [email protected]
Subject: RE: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
How about following instead of two levels of check in the while loop:
unsigned int retry = 3;
do {
live_status = intel_digital_port_connected(dev_priv,
hdmi_to_dig_port(intel_hdmi));
if (live_status)
break;
mdelay(10);
} while (--retry);Regards,
Sonika
-----Original Message-----
From: Intel-gfx [mailto:[email protected]] On Behalf Of Wang, Gary C
Sent: Friday, December 11, 2015 7:39 AM
To: [email protected]
Subject: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
The total delay of HDMI hotplug detecting with 30ms should have been split into a resolution of 3 retries of 10ms each, for the worst cases. But it still suffered from only waiting 10ms at most in intel_hdmi_detect(). This patch corrects it by reading hotplug status with 4 times at most for 30ms delay.
--- drivers/gpu/drm/i915/intel_hdmi.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) mode change 100644 => 100755 drivers/gpu/drm/i915/intel_hdmi.c
drivers/gpu/drm/i915/intel_hdmi.c +5 -2
@@ -1387,16 +1387,19 @@ intel_hdmi_detect(struct drm_connector *connector, bool force)struct intel_hdmi *intel_hdmi =intel_attached_hdmi (connector);struct drm_i915_private *dev_priv =to_i915 (connector->dev);bool live_status = false; -unsigned int retry =3 ; +// read hotplug status 4 times at most for 30ms delay (3 retries of 10ms each) +unsigned int retry =4 ;DRM_DEBUG_KMS ("[CONNECTOR:%d:%s]\n" , connector->base.id, connector->name);intel_display_power_get (dev_priv,POWER_DOMAIN_GMBUS ); -while (!live_status && --retry) { +while (!live_status && retry--) { live_status =intel_digital_port_connected (dev_priv,hdmi_to_dig_port (intel_hdmi)); +if (live_status || !retry) +break ;mdelay (10 ); }
--
1.9.1
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 85 lines · Gary C
I will upload new version of patch for review. Thanks!
-----Original Message-----
From: Intel-gfx [mailto:[email protected]] On Behalf Of Wang, Gary C
Sent: Friday, December 11, 2015 2:23 PM
To: Jindal, Sonika <[email protected]>; [email protected]
Subject: Re: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checkingNo problem.
Please refer following information.
Lenovo Mode: L246 1xwA (4/30 failed, necessary hot-plug delay: 58/40/60/40ms) Philips Model : HH2AP (9/30 failed, necessary hot-plug delay: 80/50/50/60/46/40/58/58/39ms) BENQ Model:ET-0035-N (6/30 failed, necessary hot-plug delay: 60/50/50/80/80/40ms) DELL Model:U2713HM (2/30 failed, necessary hot-plug delay: 58/59ms) HP Model: HP-LP2475w (5/30 failed, necessary hot-plug delay: 70/50/40/60/40ms)Those test were based on following test-case (test continually with 30 test cycles), 1. HDMI display correctly 2. Un-plug/re-plug HDMI cable 3. Wait for one sec
Thanks for your review!
Gary
-----Original Message-----
From: Jindal, Sonika
Sent: Friday, December 11, 2015 2:18 PM
To: Wang, Gary C <[email protected]>; [email protected]
Subject: RE: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checkingSure.
Can you please also post your findings about different panels taking different time to settle the live status so that we know that this increase in retrials is helping you with multiple monitors?Regards,
Sonika-----Original Message-----
From: Wang, Gary C
Sent: Friday, December 11, 2015 11:34 AM
To: Jindal, Sonika <[email protected]>; [email protected]
Subject: RE: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checkingHi Sonika,
Thanks for your comment, and it's more readability on code.
But it only delay 2 integration of each 10ms among checking hot-plug with 3 times. Could I change it to following snippet code to read
hotplug_status4 times at most for 3 integration 10ms delay?unsigned int retry = 3; do { live_status = intel_digital_port_connected(dev_priv, hdmi_to_dig_port(intel_hdmi)); if (live_status || !retry) break; mdelay(10); } while (retry--);Thanks!
Gary
-----Original Message-----
From: Jindal, Sonika
Sent: Friday, December 11, 2015 1:05 PM
To: Wang, Gary C <[email protected]>; [email protected]
Subject: RE: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checkingHow about following instead of two levels of check in the while loop:
unsigned int retry = 3;
do { live_status = intel_digital_port_connected(dev_priv, hdmi_to_dig_port(intel_hdmi)); if (live_status) break; mdelay(10); } while (--retry);Regards,
Sonika-----Original Message-----
From: Intel-gfx [mailto:[email protected]] On Behalf Of Wang, Gary C
Sent: Friday, December 11, 2015 7:39 AM
To: [email protected]
Subject: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
Quoted 5 lines
The total delay of HDMI hotplug detecting with 30ms should have been split into a resolution of 3 retries of 10ms each, for the worst cases. But it still suffered from only waiting 10ms at most in
intel_hdmi_detect(). This patch corrects it by reading hotplug status with 4 times at most for 30ms delay.Reviewed-by Cooper Chiou <[email protected]>Cc Gavin Hindman <[email protected]>Signed-off-by Gary Wang <[email protected]>
Can we please have less top-posting when reviewing patches? I can't really read the above with my bare-knuckles console mail client I use for reading patch mailing lists ;-)
Quoted 11 lines
--- drivers/gpu/drm/i915/intel_hdmi.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) mode change 100644 => 100755 drivers/gpu/drm/i915/intel_hdmi.cdrivers/gpu/drm/i915/intel_hdmi.c +0
-0
drivers/gpu/drm/i915/intel_hdmi.c intel_hdmi_detect(struct drm_connector *connector, bool force) · line 1390
Quoted 5 lines
drivers/gpu/drm/i915/intel_hdmi.c +1
-1@@ -1387,16 +1387,19 @@ intel_hdmi_detect(struct drm_connector *connector, bool force)struct intel_hdmi *intel_hdmi =intel_attached_hdmi (connector);struct drm_i915_private *dev_priv =to_i915 (connector->dev);bool live_status = false; -unsigned int retry =3 ; +// read hotplug status 4 times at most for 30ms delay (3 retries of 10ms each)
Please no C++ comments, also your code should be self-explanatory enough that this is obvious.
Quoted 4 lines
drivers/gpu/drm/i915/intel_hdmi.c +1
-0+unsigned int retry =4 ;DRM_DEBUG_KMS ("[CONNECTOR:%d:%s]\n" , connector->base.id, connector->name);
drivers/gpu/drm/i915/intel_hdmi.c intel_hdmi_detect(struct drm_connector *connector, bool force) · line 1403
Quoted 10 lines
drivers/gpu/drm/i915/intel_hdmi.c +3
-1intel_display_power_get (dev_priv,POWER_DOMAIN_GMBUS ); -while (!live_status && --retry) { +while (!live_status && retry--) { live_status =intel_digital_port_connected (dev_priv,hdmi_to_dig_port (intel_hdmi)); +if (live_status || !retry) +break ;mdelay (10 );
Whiel at it please review my patch to switch this one to an msleep - it's not nice to kill the battery with a busy loop like this. -Daniel
Quoted 17 lines
drivers/gpu/drm/i915/intel_hdmi.c +0
-1} --1.9.1
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 7 lines
Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
I totally agree on Ville and Daniel's comments and am sorry for incorrect text format of some description.
Following code should be more clear. It only delays 3 times (30ms delay) at most for checking hot-plug status.
- unsigned int retry = 3;
+ unsigned int retry;
DRM_DEBUG_KMS("[CONNECTOR:%d:%s]\n",
connector->base.id, connector->name);- while (!live_status && --retry) {
+ for (retry = 3; retry >= 0; retry--) {
live_status = intel_digital_port_connected(dev_priv,
hdmi_to_dig_port(intel_hdmi));
- mdelay(10);
+ if (live_status || !retry)
+ break;
+ msleep(10);
}
if (!live_status)BTW, I list again for hot-plug delay test on my BSW platform. It seems to be not enough with 30ms delay for some old HDMI monitor,
Please refer following information for my BSW platform,
1. Lenovo Mode: L246 1xwA (4/30 failed, necessary hot-plug delay: 58/40/60/40ms) ,
2. Philips Model : HH2AP (9/30 failed, necessary hot-plug delay: 80/50/50/60/46/40/58/58/39ms) ,
3. BENQ Model:ET-0035-N (6/30 failed, necessary hot-plug delay: 60/50/50/80/80/40ms) ,
4. DELL Model:U2713HM (2/30 failed, necessary hot-plug delay: 58/59ms) ,
5. HP Model: HP-LP2475w (5/30 failed, necessary hot-plug delay: 70/50/40/60/40ms),
Those test were based on following test-case (test continually with 30 test cycles)
1. HDMI display correctly
2. Un-plug/re-plug HDMI cable
3. Wait for one sec
Thanks!
Gary
-----Original Message-----
From: Daniel Vetter [mailto:[email protected]] On Behalf Of Daniel Vetter
Sent: Saturday, December 12, 2015 2:43 AM
To: Wang, Gary C <[email protected]>
Cc: Jindal, Sonika <[email protected]>; [email protected]
Subject: Re: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
Quoted 104 lines · Gary C
I will upload new version of patch for review. Thanks!
-----Original Message-----
From: Intel-gfx [mailto:[email protected]] On Behalf Of Wang, Gary C
Sent: Friday, December 11, 2015 2:23 PM
To: Jindal, Sonika <[email protected]>; [email protected]
Subject: Re: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checkingNo problem.
Please refer following information.
Lenovo Mode: L246 1xwA (4/30 failed, necessary hot-plug delay:
58/40/60/40ms) Philips Model : HH2AP (9/30 failed, necessary hot-plug
delay: 80/50/50/60/46/40/58/58/39ms) BENQ Model:ET-0035-N (6/30 failed, necessary hot-plug delay: 60/50/50/80/80/40ms) DELL Model:U2713HM (2/30 failed, necessary hot-plug delay: 58/59ms) HP
Model: HP-LP2475w (5/30 failed, necessary hot-plug delay:
70/50/40/60/40ms)Those test were based on following test-case (test continually with 30 test cycles), 1. HDMI display correctly 2. Un-plug/re-plug HDMI cable
3. Wait for one secThanks for your review!
Gary
-----Original Message-----
From: Jindal, Sonika
Sent: Friday, December 11, 2015 2:18 PM
To: Wang, Gary C <[email protected]>; [email protected]
Subject: RE: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checkingSure.
Can you please also post your findings about different panels taking different time to settle the live status so that we know that this increase in retrials is helping you with multiple monitors?Regards,
Sonika-----Original Message-----
From: Wang, Gary C
Sent: Friday, December 11, 2015 11:34 AM
To: Jindal, Sonika <[email protected]>; [email protected]
Subject: RE: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checkingHi Sonika,
Thanks for your comment, and it's more readability on code.
But it only delay 2 integration of each 10ms among checking hot-plug with 3 times. Could I change it to following snippet code to read
hotplug_status4 times at most for 3 integration 10ms delay?unsigned int retry = 3; do { live_status = intel_digital_port_connected(dev_priv, hdmi_to_dig_port(intel_hdmi)); if (live_status || !retry) break; mdelay(10); } while (retry--);Thanks!
Gary
-----Original Message-----
From: Jindal, Sonika
Sent: Friday, December 11, 2015 1:05 PM
To: Wang, Gary C <[email protected]>; [email protected]
Subject: RE: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checkingHow about following instead of two levels of check in the while loop:
unsigned int retry = 3;
do { live_status = intel_digital_port_connected(dev_priv, hdmi_to_dig_port(intel_hdmi)); if (live_status) break; mdelay(10); } while (--retry);Regards,
Sonika-----Original Message-----
From: Intel-gfx [mailto:[email protected]] On Behalf Of Wang, Gary C
Sent: Friday, December 11, 2015 7:39 AM
To: [email protected]
Subject: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checking
Quoted 5 lines
The total delay of HDMI hotplug detecting with 30ms should have been split into a resolution of 3 retries of 10ms each, for the worst cases. But it still suffered from only waiting 10ms at most in
intel_hdmi_detect(). This patch corrects it by reading hotplug status with 4 times at most for 30ms delay.Reviewed-by Cooper Chiou <[email protected]>Cc Gavin Hindman <[email protected]>Signed-off-by Gary Wang <[email protected]>
Can we please have less top-posting when reviewing patches? I can't really read the above with my bare-knuckles console mail client I use for reading patch mailing lists ;-)
Quoted 13 lines
--- drivers/gpu/drm/i915/intel_hdmi.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) mode change 100644=> 100755
drivers/gpu/drm/i915/intel_hdmi.cdrivers/gpu/drm/i915/intel_hdmi.c +0
-0
drivers/gpu/drm/i915/intel_hdmi.c intel_hdmi_detect(struct drm_connector *connector, bool force) · line 1391
Quoted 6 lines
drivers/gpu/drm/i915/intel_hdmi.c +2
-1@@ -1387,16 +1387,19 @@ intel_hdmi_detect(struct drm_connector *connector, bool force)struct intel_hdmi *intel_hdmi =intel_attached_hdmi (connector);struct drm_i915_private *dev_priv =to_i915 (connector->dev);bool live_status = false; -unsigned int retry =3 ; +// read hotplug status 4 times at most for 30ms delay (3 retries of +10ms each)
Please no C++ comments, also your code should be self-explanatory enough that this is obvious.
Quoted 4 lines
drivers/gpu/drm/i915/intel_hdmi.c +1
-0+unsigned int retry =4 ;DRM_DEBUG_KMS ("[CONNECTOR:%d:%s]\n" , connector->base.id, connector->name);
drivers/gpu/drm/i915/intel_hdmi.c intel_hdmi_detect(struct drm_connector *connector, bool force) · line 1403
Quoted 10 lines
drivers/gpu/drm/i915/intel_hdmi.c +3
-1intel_display_power_get (dev_priv,POWER_DOMAIN_GMBUS ); -while (!live_status && --retry) { +while (!live_status && retry--) { live_status =intel_digital_port_connected (dev_priv,hdmi_to_dig_port (intel_hdmi)); +if (live_status || !retry) +break ;mdelay (10 );
Whiel at it please review my patch to switch this one to an msleep - it's not nice to kill the battery with a busy loop like this. -Daniel
Quoted 5 lines
drivers/gpu/drm/i915/intel_hdmi.c +0
-1} --1.9.1
Quoted 12 lines
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 11 lines · Sonika
How about following instead of two levels of check in the while loop:
unsigned int retry = 3;
do { live_status = intel_digital_port_connected(dev_priv, hdmi_to_dig_port(intel_hdmi)); if (live_status) break; mdelay(10); } while (--retry);
How about a straight up for loop instead?
Quoted 58 lines
Regards,
Sonika-----Original Message-----
From: Intel-gfx [mailto:[email protected]] On Behalf Of Wang, Gary C
Sent: Friday, December 11, 2015 7:39 AM
To: [email protected]
Subject: [Intel-gfx] [PATCH] drm/i915: Correct max delay for HDMI hotplug live status checkingThe total delay of HDMI hotplug detecting with 30ms should have been split into a resolution of 3 retries of 10ms each, for the worst cases. But it still suffered from only waiting 10ms at most in
intel_hdmi_detect(). This patch corrects it by reading hotplug status with 4 times at most for 30ms delay.Reviewed-by Cooper Chiou <[email protected]>Cc Gavin Hindman <[email protected]>Signed-off-by Gary Wang <[email protected]>--- drivers/gpu/drm/i915/intel_hdmi.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) mode change 100644 => 100755 drivers/gpu/drm/i915/intel_hdmi.cdrivers/gpu/drm/i915/intel_hdmi.c +5
-3@@ -1387,16 +1387,19 @@ intel_hdmi_detect(struct drm_connector *connector, bool force)struct intel_hdmi *intel_hdmi =intel_attached_hdmi (connector);struct drm_i915_private *dev_priv =to_i915 (connector->dev);bool live_status = false; -unsigned int retry =3 ; +// read hotplug status 4 times at most for 30ms delay (3 retries of 10ms each) +unsigned int retry =4 ;DRM_DEBUG_KMS ("[CONNECTOR:%d:%s]\n" , connector->base.id, connector->name);intel_display_power_get (dev_priv,POWER_DOMAIN_GMBUS ); -while (!live_status && --retry) { +while (!live_status && retry--) { live_status =intel_digital_port_connected (dev_priv,hdmi_to_dig_port (intel_hdmi)); +if (live_status || !retry) +break ;mdelay (10 ); } --1.9.1
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx