IIO version of INA2xx
v4 cover IIO version of INA2xx
v4:
* squash previous small fixes into one patch and catch up with fixes from linux-iio git, 'testing' branch.
* fix endianness hint by the use of IIO_CPU, following Andrew's comment
* fix spacing issue.
* add separate ABI documentation entry
v3 and earlier : see http://www.spinics.net/lists/linux-iio/msg22100.html
Marc Titinger (2):
iio: ina2xx: add support for TI INA2xx Power Monitors
iio: ina2xx: add ABI documentation entry sysfs-bus-iio-ina2xx-adc
Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc | 24 + drivers/iio/adc/Kconfig | 10 + drivers/iio/adc/Makefile | 1 + drivers/iio/adc/ina2xx-adc.c | 745 +++++++++++++++++++++ 4 files changed, 780 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc create mode 100644 drivers/iio/adc/ina2xx-adc.c
Signature · 1 line
1.9.1
PATCH v4 1/2 iio: ina2xx: add support for TI INA2xx Power Monitors
in SOFTWARE buffer mode, a kthread will capture the active scan_elements into a kfifo, then compute the remaining time until the next capture tick and do an active wait (udelay).
This will produce a stream of up to fours channels plus a 64bits timestamps (ns).
Tested with ina226, on BeagleBoneBlack.
Datasheet: http://www.ti.com/lit/gpn/ina226
--- drivers/iio/adc/Kconfig | 10 + drivers/iio/adc/Makefile | 1 + drivers/iio/adc/ina2xx-adc.c | 745 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 756 insertions(+) create mode 100644 drivers/iio/adc/ina2xx-adc.c
drivers/iio/adc/Kconfig +10 -0
@@ -170,6 +170,16 @@ config EXYNOS_ADC of SoCs for drivers such as the touchscreen and hwmon to use to share this resource. +config INA2XX_ADC + tristate "Texas Instruments INA2xx Power Monitors IIO driver" + depends on I2C && !SENSORS_INA2XX + select REGMAP_I2C + select IIO_BUFFER + select IIO_KFIFO_BUF + help + Say yes here to build support for TI INA2xx family of Power Monitors. + This driver is mutually exclusive with the HWMON version. + config LP8788_ADC tristate "LP8788 ADC driver" depends on MFD_LP8788
drivers/iio/adc/Makefile +1 -0
@@ -19,6 +19,7 @@ obj-$(CONFIG_BERLIN2_ADC) += berlin2-adc.o obj-$(CONFIG_DA9150_GPADC) += da9150-gpadc.o obj-$(CONFIG_CC10001_ADC) += cc10001_adc.o obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o +obj-$(CONFIG_INA2XX_ADC) += ina2xx-adc.o obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o obj-$(CONFIG_MAX1027) += max1027.o obj-$(CONFIG_MAX1363) += max1363.o
drivers/iio/adc/ina2xx-adc.c new file +745 -0
745 lines not on this page · raw message
Signature · 1 line
1.9.1
PATCH v4 2/2 iio: ina2xx: add ABI documentation entry sysfs-bus-iio-ina2xx-adc
In reply to Marc TitingerDocumentation for attributes:
* in_allow_async_readout
* in_shunt_resistor
--- Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc | 24 ++++++++++++++++++++++ 1 file changed, 24 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc
Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc new file +24 -0
@@ -0,0 +1,24 @@ +What: /sys/bus/iio/devices/iio:deviceX/in_allow_async_readout +Date: December 2015 +KernelVersion: 4.4 +Contact: [email protected] +Description: + By default (value '0'), the capture thread checks for the Conversion + Ready Flag to being set prior to committing a new value to the sample + buffer. This synchronizes the in-chip conversion rate with the + in-driver readout rate at the cost of an additional register read. + + Writing '1' will remove the polling for the Conversion Ready Flags to + save the additional i2c transaction, which will improve the bandwidth + available for reading data. However, samples can be occasionally skipped + or repeated, depending on the beat between the capture and conversion + rates. + +What: /sys/bus/iio/devices/iio:deviceX/in_shunt_resistor +Date: December 2015 +KernelVersion: 4.4 +Contact: [email protected] +Description: + The value of the shunt resistor may be known only at runtime fom an + eeprom content read by a client application. This attribute allows to + set its value in ohms.
Signature · 1 line
1.9.1
Jonathan Cameron
maintainerQuoted 13 lines · Marc Titinger
v4:
* squash previous small fixes into one patch and catch up with fixes from linux-iio git, 'testing' branch.
* fix endianness hint by the use ofIIO_CPU, following Andrew's comment
* fix spacing issue.
* add separate ABI documentation entryv3 and earlier : see http://www.spinics.net/lists/linux-iio/msg22100.html
Marc Titinger (2):
iio: ina2xx: add support for TI INA2xx Power Monitors
iio: ina2xx: add ABI documentation entry sysfs-bus-iio-ina2xx-adc
Quoted 8 lines
Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc | 24 + drivers/iio/adc/Kconfig | 10 + drivers/iio/adc/Makefile | 1 + drivers/iio/adc/ina2xx-adc.c | 745 +++++++++++++++++++++ 4 files changed, 780 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc create mode 100644 drivers/iio/adc/ina2xx-adc.c
The togreg branch to which I applied the previous is a non rebasing tree and a pull request went out to Greg so a new complete version is no use now.
Jonathan Cameron
maintainerQuoted 22 lines · Jonathan Cameron
Quoted 13 lines · Marc Titinger
v4:
* squash previous small fixes into one patch and catch up with fixes from linux-iio git, 'testing' branch.
* fix endianness hint by the use ofIIO_CPU, following Andrew's comment
* fix spacing issue.
* add separate ABI documentation entryv3 and earlier : see http://www.spinics.net/lists/linux-iio/msg22100.html
Marc Titinger (2):
iio: ina2xx: add support for TI INA2xx Power Monitors
iio: ina2xx: add ABI documentation entry sysfs-bus-iio-ina2xx-adcQuoted 8 lines
Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc | 24 + drivers/iio/adc/Kconfig | 10 + drivers/iio/adc/Makefile | 1 + drivers/iio/adc/ina2xx-adc.c | 745 +++++++++++++++++++++ 4 files changed, 780 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc create mode 100644 drivers/iio/adc/ina2xx-adc.c
Quoted 4 lines
The togreg branch to which I applied the previous is a non rebasing tree and a pull request went out to Greg so a new complete version is no use now.
I've just put together a patch to fixup the wrong endianness issue and applied it to the togreg branch of iio.git as I'm preparing a pull request and want this fixed as this will be the last pull of this cycle.
Jonathan
Quoted 6 lines
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html