drm/i915/bxt: Save/Restore Backlight registers when PG0 is gated
Subsystems (2)
PATCH 1/1 drm/i915/bxt: Save/Restore Backlight registers when PG0 is gated
Currently Backlight registers which are associated with Power Well 0 are not being saved before gating the power well for S0ix. Hence, upon resume from S0ix, these registers are not being restored. Due to this, the display has resumed and since there is no backlight, nothing is seen. Patch fixes this issue by saving/restoring BLC registers for S0ix.
--- drivers/gpu/drm/i915/intel_drv.h | 4 ++++ drivers/gpu/drm/i915/intel_panel.c | 18 ++++++++++++++++++ 2 files changed, 22 insertions(+)
drivers/gpu/drm/i915/intel_drv.h +4 -0
@@ -193,6 +193,10 @@ struct intel_panel { uint32_t hz);void (*power)(struct intel_connector *,bool enable); } backlight; + +u32 blc_pwm_ctl; +u32 blc_pwm_freq; +u32 blc_pwm_duty; };struct intel_connector {
drivers/gpu/drm/i915/intel_panel.c +18 -0
@@ -816,6 +816,16 @@ static void bxt_disable_backlight(struct intel_connector *connector) val &= ~UTIL_PIN_ENABLE ;I915_WRITE (UTIL_PIN_CTL , val); } + +/* Saving BLC registers for PG0 gating */ + panel->blc_pwm_ctl = +I915_READ (BXT_BLC_PWM_CTL (panel->backlight.controller)); + panel->blc_pwm_freq = +I915_READ (BXT_BLC_PWM_FREQ (panel->backlight.controller)); + panel->blc_pwm_duty = +I915_READ (BXT_BLC_PWM_DUTY (panel->backlight.controller)); + + }static void pwm_disable_backlight (struct intel_connector *connector)
@@ -1050,6 +1060,14 @@ static void bxt_enable_backlight(struct intel_connector *connector)enum pipe pipe =intel_get_pipe_from_connector (connector);u32 pwm_ctl, val; +/* Restore BLC registers if PG0 was gated */ +I915_WRITE (BXT_BLC_PWM_CTL (panel->backlight.controller), + panel->blc_pwm_ctl); +I915_WRITE (BXT_BLC_PWM_FREQ (panel->backlight.controller), + panel->blc_pwm_freq); +I915_WRITE (BXT_BLC_PWM_DUTY (panel->backlight.controller), + panel->blc_pwm_duty); +/* To use 2nd set of backlight registers, utility pin has to be * enabled with PWM mode. * The field should only be changed when the utility pin is disabled
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✗ warning: Fi.CI.BAT
== Summary ==
== Summary ==
Built on 79686f613b3955a4ed09cee936e7f70ec4e61b67 drm-intel-nightly: 2015y-12m-30d-11h-59m-54s UTC integration manifest
Test kms_flip:
Subgroup basic-flip-vs-dpms:
dmesg-warn -> PASS (ilk-hp8440p)
Subgroup basic-flip-vs-modeset:
dmesg-warn -> PASS (skl-i5k-2)
dmesg-warn -> PASS (bsw-nuc-2)
dmesg-warn -> PASS (ilk-hp8440p)
Test kms_pipe_crc_basic:
Subgroup read-crc-pipe-a:
dmesg-warn -> PASS (snb-x220t)
dmesg-warn -> PASS (byt-nuc)
Subgroup read-crc-pipe-b:
pass -> DMESG-WARN (snb-dellxps)
Subgroup suspend-read-crc-pipe-b:
pass -> DMESG-WARN (snb-x220t)
Test kms_setmode:
Subgroup basic-clone-single-crtc:
dmesg-warn -> PASS (snb-dellxps)bdw-nuci7 total:132 pass:121 dwarn:2 dfail:0 fail:0 skip:9 bdw-ultra total:132 pass:124 dwarn:2 dfail:0 fail:0 skip:6 bsw-nuc-2 total:135 pass:114 dwarn:1 dfail:0 fail:0 skip:20 byt-nuc total:135 pass:120 dwarn:2 dfail:0 fail:0 skip:13 hsw-brixbox total:135 pass:126 dwarn:2 dfail:0 fail:0 skip:7 hsw-gt2 total:135 pass:130 dwarn:1 dfail:0 fail:0 skip:4 hsw-xps12 total:132 pass:125 dwarn:3 dfail:0 fail:0 skip:4 ilk-hp8440p total:135 pass:100 dwarn:0 dfail:0 fail:0 skip:35 ivb-t430s total:135 pass:127 dwarn:2 dfail:0 fail:0 skip:6 skl-i5k-2 total:135 pass:124 dwarn:3 dfail:0 fail:0 skip:8 skl-i7k-2 total:135 pass:124 dwarn:3 dfail:0 fail:0 skip:8 snb-dellxps total:135 pass:121 dwarn:2 dfail:0 fail:0 skip:12 snb-x220t total:135 pass:121 dwarn:2 dfail:0 fail:1 skip:11
Results at /archive/results/CI_IGT_test/Patchwork_975/
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Jani Nikula
maintainerQuoted 5 lines · Vidya Srinivas
Currently Backlight registers which are associated with Power Well 0 are not being saved before gating the power well for S0ix. Hence, upon resume from S0ix, these registers are not being restored. Due to this, the display has resumed and since there is no backlight, nothing is seen. Patch fixes this issue by saving/restoring BLC registers for S0ix.
No, this is not the approach.
The backlight disable/enable hooks should handle this by always writing the full state of the registers on enable. Doing blind register copies (and read-modify-writes) is what we've been trying to get rid of across the driver.
BR,
Jani.
Quoted 59 lines
Signed-off-by A.Sunil Kamath <[email protected]>Signed-off-by Vidya Srinivas <[email protected]>--- drivers/gpu/drm/i915/intel_drv.h | 4 ++++ drivers/gpu/drm/i915/intel_panel.c | 18 ++++++++++++++++++ 2 files changed, 22 insertions(+)drivers/gpu/drm/i915/intel_drv.h +4
-0@@ -193,6 +193,10 @@ struct intel_panel { uint32_t hz);void (*power)(struct intel_connector *,bool enable); } backlight; + +u32 blc_pwm_ctl; +u32 blc_pwm_freq; +u32 blc_pwm_duty; };struct intel_connector {drivers/gpu/drm/i915/intel_panel.c +18
-0@@ -816,6 +816,16 @@ static void bxt_disable_backlight(struct intel_connector *connector) val &= ~UTIL_PIN_ENABLE ;I915_WRITE (UTIL_PIN_CTL , val); } + +/* Saving BLC registers for PG0 gating */ + panel->blc_pwm_ctl = +I915_READ (BXT_BLC_PWM_CTL (panel->backlight.controller)); + panel->blc_pwm_freq = +I915_READ (BXT_BLC_PWM_FREQ (panel->backlight.controller)); + panel->blc_pwm_duty = +I915_READ (BXT_BLC_PWM_DUTY (panel->backlight.controller)); + + }static void pwm_disable_backlight (struct intel_connector *connector)@@ -1050,6 +1060,14 @@ static void bxt_enable_backlight(struct intel_connector *connector)enum pipe pipe =intel_get_pipe_from_connector (connector);u32 pwm_ctl, val; +/* Restore BLC registers if PG0 was gated */ +I915_WRITE (BXT_BLC_PWM_CTL (panel->backlight.controller), + panel->blc_pwm_ctl); +I915_WRITE (BXT_BLC_PWM_FREQ (panel->backlight.controller), + panel->blc_pwm_freq); +I915_WRITE (BXT_BLC_PWM_DUTY (panel->backlight.controller), + panel->blc_pwm_duty); +/* To use 2nd set of backlight registers, utility pin has to be * enabled with PWM mode. * The field should only be changed when the utility pin is disabled
Signature · 5 lines
Jani Nikula, Intel Open Source Technology Center _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Jani Nikula
maintainerQuoted 7 lines · Jani Nikula
Quoted 5 lines · Vidya Srinivas
Currently Backlight registers which are associated with Power Well 0 are not being saved before gating the power well for S0ix. Hence, upon resume from S0ix, these registers are not being restored. Due to this, the display has resumed and since there is no backlight, nothing is seen. Patch fixes this issue by saving/restoring BLC registers for S0ix.
Quoted 6 lines
No, this is not the approach.
The backlight disable/enable hooks should handle this by always writing the full state of the registers on enable. Doing blind register copies (and read-modify-writes) is what we've been trying to get rid of across the driver.
To be more specific, we *already* write the full state to the three registers in bxt_enable_backlight(). Your conclusions in the commit message are wrong. If you're seeing issues, it must be about the sequence in which the registers are written. Please look into that.
BR,
Jani.
Quoted 64 lines
BR,
Jani.Quoted 59 lines
Signed-off-by A.Sunil Kamath <[email protected]>Signed-off-by Vidya Srinivas <[email protected]>--- drivers/gpu/drm/i915/intel_drv.h | 4 ++++ drivers/gpu/drm/i915/intel_panel.c | 18 ++++++++++++++++++ 2 files changed, 22 insertions(+)drivers/gpu/drm/i915/intel_drv.h +4
-0@@ -193,6 +193,10 @@ struct intel_panel { uint32_t hz);void (*power)(struct intel_connector *,bool enable); } backlight; + +u32 blc_pwm_ctl; +u32 blc_pwm_freq; +u32 blc_pwm_duty; };struct intel_connector {drivers/gpu/drm/i915/intel_panel.c +18
-0@@ -816,6 +816,16 @@ static void bxt_disable_backlight(struct intel_connector *connector) val &= ~UTIL_PIN_ENABLE ;I915_WRITE (UTIL_PIN_CTL , val); } + +/* Saving BLC registers for PG0 gating */ + panel->blc_pwm_ctl = +I915_READ (BXT_BLC_PWM_CTL (panel->backlight.controller)); + panel->blc_pwm_freq = +I915_READ (BXT_BLC_PWM_FREQ (panel->backlight.controller)); + panel->blc_pwm_duty = +I915_READ (BXT_BLC_PWM_DUTY (panel->backlight.controller)); + + }static void pwm_disable_backlight (struct intel_connector *connector)@@ -1050,6 +1060,14 @@ static void bxt_enable_backlight(struct intel_connector *connector)enum pipe pipe =intel_get_pipe_from_connector (connector);u32 pwm_ctl, val; +/* Restore BLC registers if PG0 was gated */ +I915_WRITE (BXT_BLC_PWM_CTL (panel->backlight.controller), + panel->blc_pwm_ctl); +I915_WRITE (BXT_BLC_PWM_FREQ (panel->backlight.controller), + panel->blc_pwm_freq); +I915_WRITE (BXT_BLC_PWM_DUTY (panel->backlight.controller), + panel->blc_pwm_duty); +/* To use 2nd set of backlight registers, utility pin has to be * enabled with PWM mode. * The field should only be changed when the utility pin is disabled
Signature · 5 lines
Jani Nikula, Intel Open Source Technology Center _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx