Skip to contentSkip to conversation

iio: chemical: add atlas ph sensor support

PATCH Superseded Matt Ranostay 2 participants 6 messages Jan 18, 2016 – Jan 19, 2016

Subsystems (2)

v3 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

v3 cover iio: chemical: add atlas ph sensor support

Changes from v2:
* calibration status check to report missing reference points
* add temp range check
* switch to using both edges of interrupt option to avoid having to re-enable after every event. Which could cause a rare deadlock if an interrupt was dropped
* add missing iio_trigger_poll and irq_work queue to schedule task
* add missing ->num_channels field

Matt Ranostay (3):
devicetree: add Atlas Scientific LLC vendor prefix
iio: ph: add IIO_PH channel type
iio: chemical: add Atlas pH-SM sensor support

 Documentation/ABI/testing/sysfs-bus-iio            |   7 +
 .../bindings/iio/chemical/atlas,ph-sm.txt          |  22 +
 .../devicetree/bindings/vendor-prefixes.txt        |   1 +
 arch/arm/boot/dts/am335x-bone-common.dtsi          |   4 +-
 drivers/iio/chemical/Kconfig                       |  13 +
 drivers/iio/chemical/Makefile                      |   1 +
 drivers/iio/chemical/atlas-ph-sensor.c             | 505 +++++++++++++++++++++
 drivers/iio/industrialio-core.c                    |   1 +
 include/uapi/linux/iio/types.h                     |   1 +
 9 files changed, 553 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt
 create mode 100644 drivers/iio/chemical/atlas-ph-sensor.c
Signature · 1 line
2.7.0.rc3
#1 lore raw

PATCH v3 1/3 devicetree: add Atlas Scientific LLC vendor prefix

Add the "atlas" vendor prefix for Atlas Scientific LLC

---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/vendor-prefixes.txt +1 -0
index 72e2c5a..44ddc98 100644
@@ -28,6 +28,7 @@ arm	ARM Ltd.
 armadeus	ARMadeus Systems SARL
 artesyn	Artesyn Embedded Technologies Inc.
 asahi-kasei	Asahi Kasei Corp.
+atlas	Atlas Scientific LLC
 atmel	Atmel Corporation
 auo	AU Optronics Corporation
 avago	Avago Technologies
Signature · 1 line
2.7.0.rc3
#2 lore raw

PATCH v3 2/3 iio: ph: add IIO_PH channel type

In reply to Matt Ranostay
---
 Documentation/ABI/testing/sysfs-bus-iio | 7 +++++++
 drivers/iio/industrialio-core.c         | 1 +
 include/uapi/linux/iio/types.h          | 1 +
 3 files changed, 9 insertions(+)
Documentation/ABI/testing/sysfs-bus-iio +7 -0
index 0439c2a..86ba8d6 100644
@@ -1491,3 +1491,10 @@ Description:
 		This ABI is especially applicable for humidity sensors
 		to heatup the device and get rid of any condensation
 		in some humidity environment
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_ph_raw
+KernelVersion:	4.5
+Contact:	[email protected]
+Description:
+		Raw (unscaled no offset etc.) pH reading of a substance as a negative
+		base-10 logarithm of hydrodium ions in a litre of water.
drivers/iio/industrialio-core.c +1 -0
index af7cc1e..70cb7eb 100644
@@ -77,6 +77,7 @@ static const char * const iio_chan_type_name_spec[] = {
 	[IIO_VELOCITY] = "velocity",
 	[IIO_CONCENTRATION] = "concentration",
 	[IIO_RESISTANCE] = "resistance",
+	[IIO_PH] = "ph",
 };
 
 static const char * const iio_modifier_names[] = {
include/uapi/linux/iio/types.h +1 -0
index 7c63bd6..c077617 100644
@@ -37,6 +37,7 @@ enum iio_chan_type {
 	IIO_VELOCITY,
 	IIO_CONCENTRATION,
 	IIO_RESISTANCE,
+	IIO_PH,
 };
 
 enum iio_modifier {
Signature · 1 line
2.7.0.rc3
#3 lore raw

PATCH v3 3/3 iio: chemical: add Atlas pH-SM sensor support

In reply to Matt Ranostay

Add support for the Atlas Scientific pH-SM chemical sensor that can detect pH levels of solutions in the range of 0-14.

---
 .../bindings/iio/chemical/atlas,ph-sm.txt          |  22 +
 drivers/iio/chemical/Kconfig                       |  13 +
 drivers/iio/chemical/Makefile                      |   1 +
 drivers/iio/chemical/atlas-ph-sensor.c             | 505 +++++++++++++++++++++
 4 files changed, 541 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt
 create mode 100644 drivers/iio/chemical/atlas-ph-sensor.c
Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt new file +22 -0
new file mode 100644
index 0000000..cffa190
@@ -0,0 +1,22 @@
+* Atlas Scientific pH-SM OEM sensor
+
+http://www.atlas-scientific.com/_files/_datasheets/_oem/pH_oem_datasheet.pdf
+
+Required properties:
+
+  - compatible: must be "atlas,ph-sm"
+  - reg: the I2C address of the sensor
+  - interrupt-parent: should be the phandle for the interrupt controller
+  - interrupts: the sole interrupt generated by the device
+
+  Refer to interrupt-controller/interrupts.txt for generic interrupt client
+  node bindings.
+
+Example:
+
+atlas@65 {
+	compatible = "atlas,ph-sm";
+	reg = <0x65>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <16 2>;
+};
drivers/iio/chemical/Kconfig +13 -0
index f16de61..ce7cd1370 100644
@@ -4,6 +4,19 @@
 
 menu "Chemical Sensors"
 
+config ATLAS_PH_SENSOR
+	tristate "Atlas Scientific OEM pH-SM sensor"
+	depends on I2C
+	select REGMAP_I2C
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
+	help
+	 Say Y here to build I2C interface support for the Atlas
+	 Scientific OEM pH-SM sensor.
+
+	 To compile this driver as module, choose M here: the
+	 module will be called atlas-ph-sensor.
+
 config IAQCORE
 	tristate "AMS iAQ-Core VOC sensors"
 	depends on I2C
drivers/iio/chemical/Makefile +1 -0
index 167861f..b02202b 100644
@@ -3,5 +3,6 @@
 #
 
 # When adding new entries keep the list in alphabetical order
+obj-$(CONFIG_ATLAS_PH_SENSOR)	+= atlas-ph-sensor.o
 obj-$(CONFIG_IAQCORE)		+= ams-iaq-core.o
 obj-$(CONFIG_VZ89X)		+= vz89x.o
drivers/iio/chemical/atlas-ph-sensor.c new file +505 -0

505 lines not on this page · raw message

Signature · 1 line
2.7.0.rc3
#4 lore raw

Re: [PATCH v3 3/3] iio: chemical: add Atlas pH-SM sensor support

Quoted 3 lines

Add support for the Atlas Scientific pH-SM chemical sensor that can detect pH levels of solutions in the range of 0-14.

looks mostly good to me

why is regmap_bulk_read() used for _TEMP, but
i2c_smbus_read_i2c_block_data() for _PH?

I2C_FUNC_SMBUS_READ_BLOCK_DATA may not be supported, could check in _probe()

Quoted 188 lines
---
 .../bindings/iio/chemical/atlas,ph-sm.txt          |  22 +
 drivers/iio/chemical/Kconfig                       |  13 +
 drivers/iio/chemical/Makefile                      |   1 +
 drivers/iio/chemical/atlas-ph-sensor.c             | 505 +++++++++++++++++++++
 4 files changed, 541 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt
 create mode 100644 drivers/iio/chemical/atlas-ph-sensor.c
Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt new file +22 -0
new file mode 100644
index 0000000..cffa190
@@ -0,0 +1,22 @@
+* Atlas Scientific pH-SM OEM sensor
+
+http://www.atlas-scientific.com/_files/_datasheets/_oem/pH_oem_datasheet.pdf
+
+Required properties:
+
+  - compatible: must be "atlas,ph-sm"
+  - reg: the I2C address of the sensor
+  - interrupt-parent: should be the phandle for the interrupt controller
+  - interrupts: the sole interrupt generated by the device
+
+  Refer to interrupt-controller/interrupts.txt for generic interrupt client
+  node bindings.
+
+Example:
+
+atlas@65 {
+	compatible = "atlas,ph-sm";
+	reg = <0x65>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <16 2>;
+};
drivers/iio/chemical/Kconfig +13 -0
index f16de61..ce7cd1370 100644
@@ -4,6 +4,19 @@
 
 menu "Chemical Sensors"
 
+config ATLAS_PH_SENSOR
+	tristate "Atlas Scientific OEM pH-SM sensor"
+	depends on I2C
+	select REGMAP_I2C
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
+	help
+	 Say Y here to build I2C interface support for the Atlas
+	 Scientific OEM pH-SM sensor.
+
+	 To compile this driver as module, choose M here: the
+	 module will be called atlas-ph-sensor.
+
 config IAQCORE
 	tristate "AMS iAQ-Core VOC sensors"
 	depends on I2C
drivers/iio/chemical/Makefile +1 -0
index 167861f..b02202b 100644
@@ -3,5 +3,6 @@
 #
 
 # When adding new entries keep the list in alphabetical order
+obj-$(CONFIG_ATLAS_PH_SENSOR)	+= atlas-ph-sensor.o
 obj-$(CONFIG_IAQCORE)		+= ams-iaq-core.o
 obj-$(CONFIG_VZ89X)		+= vz89x.o
drivers/iio/chemical/atlas-ph-sensor.c new file +109 -0
new file mode 100644
index 0000000..775e85c
@@ -0,0 +1,505 @@
+/*
+ * atlas-ph-sensor.c - Support for Atlas Scientific OEM pH-SM sensor
+ *
+ * Copyright (C) 2015 Matt Ranostay <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/mutex.h>
+#include <linux/err.h>
+#include <linux/irq.h>
+#include <linux/irq_work.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/trigger.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/pm_runtime.h>
+
+#define ATLAS_REGMAP_NAME	"atlas_ph_regmap"
+#define ATLAS_DRV_NAME		"atlas_ph"
+
+#define ATLAS_REG_DEV_TYPE		0x00
+#define ATLAS_REG_DEV_VERSION		0x01
+
+#define ATLAS_REG_INT_CONTROL		0x04
+#define ATLAS_REG_INT_CONTROL_EN	BIT(3)
+
+#define ATLAS_REG_PWR_CONTROL		0x06
+
+#define ATLAS_REG_CALIB_STATUS		0x0d
+#define ATLAS_REG_CALIB_STATUS_MASK	0x07
+#define ATLAS_REG_CALIB_STATUS_LOW	BIT(0)
+#define ATLAS_REG_CALIB_STATUS_MID	BIT(1)
+#define ATLAS_REG_CALIB_STATUS_HIGH	BIT(2)
+
+#define ATLAS_REG_TEMP_DATA_1		0x0e
+#define ATLAS_REG_TEMP_DATA_2		0x0f
+#define ATLAS_REG_TEMP_DATA_3		0x10
+#define ATLAS_REG_TEMP_DATA_4		0x11
+#define ATLAS_REG_PH_DATA		0x16
+
+#define ATLAS_PH_INT_TIME_IN_US		450000
+
+struct atlas_data {
+	struct i2c_client *client;
+	struct iio_trigger *trig;
+	struct regmap *regmap;
+	struct irq_work work;
+
+	__be32 buffer[4]; /* 32-bit pH data + 32-bit pad + 64-bit timestamp */
+};
+
+static bool atlas_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case ATLAS_REG_INT_CONTROL:
+	case ATLAS_REG_TEMP_DATA_1:
+	case ATLAS_REG_TEMP_DATA_2:
+	case ATLAS_REG_TEMP_DATA_3:
+	case ATLAS_REG_TEMP_DATA_4:
+		return true;
+	}
+
+	return false;
+}
+
+static const struct regmap_config atlas_regmap_config = {
+	.name = ATLAS_REGMAP_NAME,
+
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.volatile_reg = atlas_is_volatile_reg,
+	.max_register = ATLAS_REG_PH_DATA + 4,
+	.cache_type = REGCACHE_FLAT,
+};
+
+static const struct iio_chan_spec atlas_channels[] = {
+	{
+		.type = IIO_PH,
+		.info_mask_separate =
+			BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
+		.scan_index = 0,
+		.scan_type = {
+			.sign = 'u',
+			.realbits = 32,
+			.storagebits = 32,
+			.endianness = IIO_BE,
+		},
+	},
+	IIO_CHAN_SOFT_TIMESTAMP(1),
+	{

drivers/iio/chemical/atlas-ph-sensor.c line 119

Quoted 10 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +10 -0
+		.type = IIO_TEMP,
+		.address = ATLAS_REG_TEMP_DATA_1,
+		.info_mask_separate =
+			BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
+		.output = 1,
+		.scan_index = -1
+	},
+};
+
+static int atlas_set_powermode(struct atlas_data *data, int on)

maybe bool on

Quoted 163 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +163 -0
+{
+	return regmap_write(data->regmap, ATLAS_REG_PWR_CONTROL, on);
+}
+
+static int atlas_set_interrupt(struct atlas_data *data, bool state)
+{
+	return regmap_update_bits(data->regmap, ATLAS_REG_INT_CONTROL,
+				  ATLAS_REG_INT_CONTROL_EN,
+				  state ? ATLAS_REG_INT_CONTROL_EN : 0);
+}
+
+static int atlas_buffer_postenable(struct iio_dev *indio_dev)
+{
+	struct atlas_data *data = iio_priv(indio_dev);
+	int ret;
+
+	ret = iio_triggered_buffer_postenable(indio_dev);
+	if (ret)
+		return ret;
+
+	ret = pm_runtime_get_sync(&data->client->dev);
+	if (ret < 0) {
+		pm_runtime_put_noidle(&data->client->dev);
+		return ret;
+	}
+
+	return atlas_set_interrupt(data, true);
+}
+
+static int atlas_buffer_predisable(struct iio_dev *indio_dev)
+{
+	struct atlas_data *data = iio_priv(indio_dev);
+	int ret;
+
+	ret = iio_triggered_buffer_predisable(indio_dev);
+	if (ret)
+		return ret;
+
+	ret = atlas_set_interrupt(data, false);
+	if (ret)
+		return ret;
+
+	pm_runtime_mark_last_busy(&data->client->dev);
+	return pm_runtime_put_autosuspend(&data->client->dev);
+}
+
+static const struct iio_trigger_ops atlas_interrupt_trigger_ops = {
+	.owner = THIS_MODULE,
+};
+
+static const struct iio_buffer_setup_ops atlas_buffer_setup_ops = {
+	.postenable = atlas_buffer_postenable,
+	.predisable = atlas_buffer_predisable,
+};
+
+static void atlas_work_handler(struct irq_work *work)
+{
+	struct atlas_data *data = container_of(work, struct atlas_data, work);
+
+	iio_trigger_poll(data->trig);
+}
+
+static irqreturn_t atlas_trigger_handler(int irq, void *private)
+{
+	struct iio_poll_func *pf = private;
+	struct iio_dev *indio_dev = pf->indio_dev;
+	struct atlas_data *data = iio_priv(indio_dev);
+	int ret;
+
+	ret = i2c_smbus_read_i2c_block_data(data->client, ATLAS_REG_PH_DATA,
+				sizeof(data->buffer[0]), (u8 *) &data->buffer);
+
+	if (ret > 0)
+		iio_push_to_buffers_with_timestamp(indio_dev, data->buffer,
+				iio_get_time_ns());
+
+	iio_trigger_notify_done(indio_dev->trig);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t atlas_interrupt_handler(int irq, void *private)
+{
+	struct iio_dev *indio_dev = private;
+	struct atlas_data *data = iio_priv(indio_dev);
+
+	irq_work_queue(&data->work);
+
+	return IRQ_HANDLED;
+}
+
+static int atlas_read_ph_measurement(struct atlas_data *data, __be32 *val)
+{
+	struct device *dev = &data->client->dev;
+	int suspended = pm_runtime_suspended(dev);
+	int ret, cnt = 0;
+
+	ret = pm_runtime_get_sync(dev);
+	if (ret < 0) {
+		pm_runtime_put_noidle(dev);
+		return ret;
+	}
+
+	if (suspended)
+		usleep_range(ATLAS_PH_INT_TIME_IN_US,
+			     ATLAS_PH_INT_TIME_IN_US + 100000);
+
+	cnt = i2c_smbus_read_i2c_block_data(data->client, ATLAS_REG_PH_DATA,
+					    sizeof(*val), (u8 *) val);
+
+	pm_runtime_mark_last_busy(dev);
+	ret = pm_runtime_put_autosuspend(dev);
+	if (ret)
+		return ret;
+
+	return cnt == sizeof(*val) ? 0 : -EINVAL;
+}
+
+static int atlas_read_raw(struct iio_dev *indio_dev,
+			  struct iio_chan_spec const *chan,
+			  int *val, int *val2, long mask)
+{
+	struct atlas_data *data = iio_priv(indio_dev);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW: {
+		int ret;
+		__be32 reg;
+
+		mutex_lock(&indio_dev->mlock);
+
+		if (iio_buffer_enabled(indio_dev)) {
+			ret = -EBUSY;
+			goto error_busy;
+		}
+
+		switch (chan->type) {
+		case IIO_TEMP:
+			ret = regmap_bulk_read(data->regmap, chan->address,
+					      (u8 *) &reg, sizeof(reg));
+			break;
+		case IIO_PH:
+			ret = atlas_read_ph_measurement(data, &reg);
+			break;
+		default:
+			ret = -EINVAL;
+		}
+
+		if (!ret) {
+			*val = be32_to_cpu(reg);
+			ret = IIO_VAL_INT;
+		}
+error_busy:
+		mutex_unlock(&indio_dev->mlock);
+		return ret;
+	}
+	case IIO_CHAN_INFO_SCALE:
+		*val = 0; /* 0.001 */
+		*val2 = 1000;
+		return IIO_VAL_INT_PLUS_MICRO;
+	}
+
+	return -EINVAL;

drivers/iio/chemical/atlas-ph-sensor.c line 292

Quoted 10 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +10 -0
+}
+
+static int atlas_write_raw(struct iio_dev *indio_dev,
+			   struct iio_chan_spec const *chan,
+			   int val, int val2, long mask)
+{
+	struct atlas_data *data = iio_priv(indio_dev);
+	__be32 reg = cpu_to_be32(val);
+
+	if (val2 > 0 || val < 0 || val > 20000)

probably clearer to check val2 != 0

drivers/iio/chemical/atlas-ph-sensor.c line 298

Quoted 6 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +6 -0
+		return -EINVAL;
+
+	if (mask != IIO_CHAN_INFO_RAW || chan->type != IIO_TEMP)
+		return -EINVAL;
+
+	return regmap_bulk_write(data->regmap, chan->address, &reg, 4);

everywhere else sizeof(__be32) instead of 4

Quoted 10 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +10 -0
+}
+
+static const struct iio_info atlas_info = {
+	.driver_module = THIS_MODULE,
+	.read_raw = atlas_read_raw,
+	.write_raw = atlas_write_raw,
+};
+
+static int atlas_check_calibration(struct atlas_data *data)
+{

drivers/iio/chemical/atlas-ph-sensor.c line 318

Quoted 10 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +10 -0
+	struct device *dev = &data->client->dev;
+	int ret;
+	unsigned int val;
+
+	ret = regmap_read(data->regmap, ATLAS_REG_CALIB_STATUS, &val);
+	if (ret)
+		return ret;
+
+	if (!(val & ATLAS_REG_CALIB_STATUS_MASK)) {
+		dev_warn(dev, "device has not been calibrated");

\n at the end

drivers/iio/chemical/atlas-ph-sensor.c line 319

Quoted 1 line
drivers/iio/chemical/atlas-ph-sensor.c new file +1 -0
+		return 0;

maybe an error code here?

Quoted 86 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +86 -0
+	}
+
+	if (!(val & ATLAS_REG_CALIB_STATUS_LOW))
+		dev_warn(dev, "device missing low point calibration");
+
+	if (!(val & ATLAS_REG_CALIB_STATUS_MID))
+		dev_warn(dev, "device missing mid point calibration");
+
+	if (!(val & ATLAS_REG_CALIB_STATUS_HIGH))
+		dev_warn(dev, "device missing high point calibration");
+
+	return 0;
+};
+
+static int atlas_probe(struct i2c_client *client,
+		       const struct i2c_device_id *id)
+{
+	struct atlas_data *data;
+	struct iio_trigger *trig;
+	struct iio_dev *indio_dev;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	indio_dev->info = &atlas_info;
+	indio_dev->name = ATLAS_DRV_NAME;
+	indio_dev->channels = atlas_channels;
+	indio_dev->num_channels = ARRAY_SIZE(atlas_channels);
+	indio_dev->modes = INDIO_BUFFER_SOFTWARE | INDIO_DIRECT_MODE;
+	indio_dev->dev.parent = &client->dev;
+
+	trig = devm_iio_trigger_alloc(&client->dev, "%s-dev%d",
+				      indio_dev->name, indio_dev->id);
+
+	if (!trig)
+		return -ENOMEM;
+
+	data = iio_priv(indio_dev);
+	data->client = client;
+	data->trig = trig;
+	trig->dev.parent = indio_dev->dev.parent;
+	trig->ops = &atlas_interrupt_trigger_ops;
+	iio_trigger_set_drvdata(trig, indio_dev);
+
+	i2c_set_clientdata(client, indio_dev);
+
+	data->regmap = devm_regmap_init_i2c(client, &atlas_regmap_config);
+	if (IS_ERR(data->regmap)) {
+		dev_err(&client->dev, "regmap initialization failed\n");
+		return PTR_ERR(data->regmap);
+	}
+
+	ret = pm_runtime_set_active(&client->dev);
+	if (ret)
+		return ret;
+
+	if (client->irq <= 0) {
+		dev_err(&client->dev, "no valid irq defined\n");
+		return -EINVAL;
+	}
+
+	ret = atlas_check_calibration(data);
+	if (ret)
+		return ret;
+
+	ret = iio_trigger_register(trig);
+	if (ret) {
+		dev_err(&client->dev, "failed to register trigger\n");
+		return ret;
+	}
+
+	ret = iio_triggered_buffer_setup(indio_dev, &iio_pollfunc_store_time,
+		&atlas_trigger_handler, &atlas_buffer_setup_ops);
+	if (ret) {
+		dev_err(&client->dev, "cannot setup iio trigger\n");
+		goto unregister_trigger;
+	}
+
+	init_irq_work(&data->work, atlas_work_handler);
+
+	ret = devm_request_threaded_irq(&client->dev, client->irq,
+					NULL, atlas_interrupt_handler,
+					IRQF_TRIGGER_RISING |
+					IRQF_TRIGGER_FALLING | IRQF_ONESHOT,

drivers/iio/chemical/atlas-ph-sensor.c line 415

Quoted 10 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +10 -0
+					"atlas_irq",
+					indio_dev);
+	if (ret) {
+		dev_err(&client->dev, "request irq (%d) failed\n", client->irq);
+		goto unregister_buffer;
+	}
+
+	ret = atlas_set_powermode(data, 1);
+	if (ret) {
+		dev_err(&client->dev, "cannot power device on");

\n

Quoted 91 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +90 -0
+		goto unregister_buffer;
+	}
+
+	pm_runtime_enable(&client->dev);
+	pm_runtime_set_autosuspend_delay(&client->dev, 2500);
+	pm_runtime_use_autosuspend(&client->dev);
+
+	ret = iio_device_register(indio_dev);
+	if (ret) {
+		dev_err(&client->dev, "unable to register device\n");
+		goto unregister_buffer;
+	}
+
+	return 0;
+
+unregister_buffer:
+	iio_triggered_buffer_cleanup(indio_dev);
+
+unregister_trigger:
+	iio_trigger_unregister(data->trig);
+
+	return ret;
+}
+
+static int atlas_remove(struct i2c_client *client)
+{
+	struct iio_dev *indio_dev = i2c_get_clientdata(client);
+	struct atlas_data *data = iio_priv(indio_dev);
+
+	iio_device_unregister(indio_dev);
+	iio_triggered_buffer_cleanup(indio_dev);
+	iio_trigger_unregister(data->trig);
+
+	pm_runtime_disable(&client->dev);
+	pm_runtime_set_suspended(&client->dev);
+	pm_runtime_put_noidle(&client->dev);
+
+	return atlas_set_powermode(data, 0);
+}
+
+#ifdef CONFIG_PM
+static int atlas_runtime_suspend(struct device *dev)
+{
+	struct atlas_data *data =
+		     iio_priv(i2c_get_clientdata(to_i2c_client(dev)));
+
+	return atlas_set_powermode(data, 0);
+}
+
+static int atlas_runtime_resume(struct device *dev)
+{
+	struct atlas_data *data =
+		     iio_priv(i2c_get_clientdata(to_i2c_client(dev)));
+
+	return atlas_set_powermode(data, 1);
+}
+#endif
+
+static const struct dev_pm_ops atlas_pm_ops = {
+	SET_RUNTIME_PM_OPS(atlas_runtime_suspend,
+			   atlas_runtime_resume, NULL)
+};
+
+static const struct i2c_device_id atlas_id[] = {
+	{ "atlas-ph-sm", 0 },
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, atlas_id);
+
+static const struct of_device_id atlas_dt_ids[] = {
+	{ .compatible = "atlas,ph-sm" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, atlas_dt_ids);
+
+static struct i2c_driver atlas_driver = {
+	.driver = {
+		.name	= ATLAS_DRV_NAME,
+		.of_match_table	= of_match_ptr(atlas_dt_ids),
+		.pm	= &atlas_pm_ops,
+	},
+	.probe		= atlas_probe,
+	.remove		= atlas_remove,
+	.id_table	= atlas_id,
+};
+module_i2c_driver(atlas_driver);
+
+MODULE_AUTHOR("Matt Ranostay <[email protected]>");
+MODULE_DESCRIPTION("Atlas Scientific pH-SM sensor");
+MODULE_LICENSE("GPL");
Signature · 2 lines
Peter Meerwald-Stadler
+43-664-2444418 (mobile)
#5 lore raw

Re: [PATCH v3 3/3] iio: chemical: add Atlas pH-SM sensor support

Quoted 8 lines · Peter Meerwald-Stadler
Quoted 3 lines

Add support for the Atlas Scientific pH-SM chemical sensor that can detect pH levels of solutions in the range of 0-14.

looks mostly good to me

why is regmap_bulk_read() used for _TEMP, but
i2c_smbus_read_i2c_block_data() for _PH?

Gah yeah have no excuse besides I forgot i was using i2c_smbus_read_i2c_block_data beforehand. Will fix.

Quoted 3 lines

I2C_FUNC_SMBUS_READ_BLOCK_DATA may not be supported, could check in _probe()

Got it.

Quoted 369 lines
Quoted 189 lines
---
 .../bindings/iio/chemical/atlas,ph-sm.txt          |  22 +
 drivers/iio/chemical/Kconfig                       |  13 +
 drivers/iio/chemical/Makefile                      |   1 +
 drivers/iio/chemical/atlas-ph-sensor.c             | 505 +++++++++++++++++++++
 4 files changed, 541 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt
 create mode 100644 drivers/iio/chemical/atlas-ph-sensor.c
Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt new file +22 -0
new file mode 100644
index 0000000..cffa190
@@ -0,0 +1,22 @@
+* Atlas Scientific pH-SM OEM sensor
+
+http://www.atlas-scientific.com/_files/_datasheets/_oem/pH_oem_datasheet.pdf
+
+Required properties:
+
+  - compatible: must be "atlas,ph-sm"
+  - reg: the I2C address of the sensor
+  - interrupt-parent: should be the phandle for the interrupt controller
+  - interrupts: the sole interrupt generated by the device
+
+  Refer to interrupt-controller/interrupts.txt for generic interrupt client
+  node bindings.
+
+Example:
+
+atlas@65 {
+     compatible = "atlas,ph-sm";
+     reg = <0x65>;
+     interrupt-parent = <&gpio1>;
+     interrupts = <16 2>;
+};
drivers/iio/chemical/Kconfig +13 -0
index f16de61..ce7cd1370 100644
@@ -4,6 +4,19 @@
 
 menu "Chemical Sensors"
 
+config ATLAS_PH_SENSOR
+     tristate "Atlas Scientific OEM pH-SM sensor"
+     depends on I2C
+     select REGMAP_I2C
+     select IIO_BUFFER
+     select IIO_TRIGGERED_BUFFER
+     help
+      Say Y here to build I2C interface support for the Atlas
+      Scientific OEM pH-SM sensor.
+
+      To compile this driver as module, choose M here: the
+      module will be called atlas-ph-sensor.
+
 config IAQCORE
      tristate "AMS iAQ-Core VOC sensors"
      depends on I2C
drivers/iio/chemical/Makefile +1 -0
index 167861f..b02202b 100644
@@ -3,5 +3,6 @@
 #
 
 # When adding new entries keep the list in alphabetical order
+obj-$(CONFIG_ATLAS_PH_SENSOR)        += atlas-ph-sensor.o
 obj-$(CONFIG_IAQCORE)                += ams-iaq-core.o
 obj-$(CONFIG_VZ89X)          += vz89x.o
drivers/iio/chemical/atlas-ph-sensor.c new file +109 -0
new file mode 100644
index 0000000..775e85c
@@ -0,0 +1,505 @@
+/*
+ * atlas-ph-sensor.c - Support for Atlas Scientific OEM pH-SM sensor
+ *
+ * Copyright (C) 2015 Matt Ranostay <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/mutex.h>
+#include <linux/err.h>
+#include <linux/irq.h>
+#include <linux/irq_work.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/trigger.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/pm_runtime.h>
+
+#define ATLAS_REGMAP_NAME    "atlas_ph_regmap"
+#define ATLAS_DRV_NAME               "atlas_ph"
+
+#define ATLAS_REG_DEV_TYPE           0x00
+#define ATLAS_REG_DEV_VERSION                0x01
+
+#define ATLAS_REG_INT_CONTROL                0x04
+#define ATLAS_REG_INT_CONTROL_EN     BIT(3)
+
+#define ATLAS_REG_PWR_CONTROL                0x06
+
+#define ATLAS_REG_CALIB_STATUS               0x0d
+#define ATLAS_REG_CALIB_STATUS_MASK  0x07
+#define ATLAS_REG_CALIB_STATUS_LOW   BIT(0)
+#define ATLAS_REG_CALIB_STATUS_MID   BIT(1)
+#define ATLAS_REG_CALIB_STATUS_HIGH  BIT(2)
+
+#define ATLAS_REG_TEMP_DATA_1                0x0e
+#define ATLAS_REG_TEMP_DATA_2                0x0f
+#define ATLAS_REG_TEMP_DATA_3                0x10
+#define ATLAS_REG_TEMP_DATA_4                0x11
+#define ATLAS_REG_PH_DATA            0x16
+
+#define ATLAS_PH_INT_TIME_IN_US              450000
+
+struct atlas_data {
+     struct i2c_client *client;
+     struct iio_trigger *trig;
+     struct regmap *regmap;
+     struct irq_work work;
+
+     __be32 buffer[4]; /* 32-bit pH data + 32-bit pad + 64-bit timestamp */
+};
+
+static bool atlas_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+     switch (reg) {
+     case ATLAS_REG_INT_CONTROL:
+     case ATLAS_REG_TEMP_DATA_1:
+     case ATLAS_REG_TEMP_DATA_2:
+     case ATLAS_REG_TEMP_DATA_3:
+     case ATLAS_REG_TEMP_DATA_4:
+             return true;
+     }
+
+     return false;
+}
+
+static const struct regmap_config atlas_regmap_config = {
+     .name = ATLAS_REGMAP_NAME,
+
+     .reg_bits = 8,
+     .val_bits = 8,
+
+     .volatile_reg = atlas_is_volatile_reg,
+     .max_register = ATLAS_REG_PH_DATA + 4,
+     .cache_type = REGCACHE_FLAT,
+};
+
+static const struct iio_chan_spec atlas_channels[] = {
+     {
+             .type = IIO_PH,
+             .info_mask_separate =
+                     BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
+             .scan_index = 0,
+             .scan_type = {
+                     .sign = 'u',
+                     .realbits = 32,
+                     .storagebits = 32,
+                     .endianness = IIO_BE,
+             },
+     },
+     IIO_CHAN_SOFT_TIMESTAMP(1),
+     {

drivers/iio/chemical/atlas-ph-sensor.c line 119

Quoted 10 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +10 -0
+             .type = IIO_TEMP,
+             .address = ATLAS_REG_TEMP_DATA_1,
+             .info_mask_separate =
+                     BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
+             .output = 1,
+             .scan_index = -1
+     },
+};
+
+static int atlas_set_powermode(struct atlas_data *data, int on)

maybe bool on

Quoted 167 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +167 -0
+{
+     return regmap_write(data->regmap, ATLAS_REG_PWR_CONTROL, on);
+}
+
+static int atlas_set_interrupt(struct atlas_data *data, bool state)
+{
+     return regmap_update_bits(data->regmap, ATLAS_REG_INT_CONTROL,
+                               ATLAS_REG_INT_CONTROL_EN,
+                               state ? ATLAS_REG_INT_CONTROL_EN : 0);
+}
+
+static int atlas_buffer_postenable(struct iio_dev *indio_dev)
+{
+     struct atlas_data *data = iio_priv(indio_dev);
+     int ret;
+
+     ret = iio_triggered_buffer_postenable(indio_dev);
+     if (ret)
+             return ret;
+
+     ret = pm_runtime_get_sync(&data->client->dev);
+     if (ret < 0) {
+             pm_runtime_put_noidle(&data->client->dev);
+             return ret;
+     }
+
+     return atlas_set_interrupt(data, true);
+}
+
+static int atlas_buffer_predisable(struct iio_dev *indio_dev)
+{
+     struct atlas_data *data = iio_priv(indio_dev);
+     int ret;
+
+     ret = iio_triggered_buffer_predisable(indio_dev);
+     if (ret)
+             return ret;
+
+     ret = atlas_set_interrupt(data, false);
+     if (ret)
+             return ret;
+
+     pm_runtime_mark_last_busy(&data->client->dev);
+     return pm_runtime_put_autosuspend(&data->client->dev);
+}
+
+static const struct iio_trigger_ops atlas_interrupt_trigger_ops = {
+     .owner = THIS_MODULE,
+};
+
+static const struct iio_buffer_setup_ops atlas_buffer_setup_ops = {
+     .postenable = atlas_buffer_postenable,
+     .predisable = atlas_buffer_predisable,
+};
+
+static void atlas_work_handler(struct irq_work *work)
+{
+     struct atlas_data *data = container_of(work, struct atlas_data, work);
+
+     iio_trigger_poll(data->trig);
+}
+
+static irqreturn_t atlas_trigger_handler(int irq, void *private)
+{
+     struct iio_poll_func *pf = private;
+     struct iio_dev *indio_dev = pf->indio_dev;
+     struct atlas_data *data = iio_priv(indio_dev);
+     int ret;
+
+     ret = i2c_smbus_read_i2c_block_data(data->client, ATLAS_REG_PH_DATA,
+                             sizeof(data->buffer[0]), (u8 *) &data->buffer);
+
+     if (ret > 0)
+             iio_push_to_buffers_with_timestamp(indio_dev, data->buffer,
+                             iio_get_time_ns());
+
+     iio_trigger_notify_done(indio_dev->trig);
+
+     return IRQ_HANDLED;
+}
+
+static irqreturn_t atlas_interrupt_handler(int irq, void *private)
+{
+     struct iio_dev *indio_dev = private;
+     struct atlas_data *data = iio_priv(indio_dev);
+
+     irq_work_queue(&data->work);
+
+     return IRQ_HANDLED;
+}
+
+static int atlas_read_ph_measurement(struct atlas_data *data, __be32 *val)
+{
+     struct device *dev = &data->client->dev;
+     int suspended = pm_runtime_suspended(dev);
+     int ret, cnt = 0;
+
+     ret = pm_runtime_get_sync(dev);
+     if (ret < 0) {
+             pm_runtime_put_noidle(dev);
+             return ret;
+     }
+
+     if (suspended)
+             usleep_range(ATLAS_PH_INT_TIME_IN_US,
+                          ATLAS_PH_INT_TIME_IN_US + 100000);
+
+     cnt = i2c_smbus_read_i2c_block_data(data->client, ATLAS_REG_PH_DATA,
+                                         sizeof(*val), (u8 *) val);
+
+     pm_runtime_mark_last_busy(dev);
+     ret = pm_runtime_put_autosuspend(dev);
+     if (ret)
+             return ret;
+
+     return cnt == sizeof(*val) ? 0 : -EINVAL;
+}
+
+static int atlas_read_raw(struct iio_dev *indio_dev,
+                       struct iio_chan_spec const *chan,
+                       int *val, int *val2, long mask)
+{
+     struct atlas_data *data = iio_priv(indio_dev);
+
+     switch (mask) {
+     case IIO_CHAN_INFO_RAW: {
+             int ret;
+             __be32 reg;
+
+             mutex_lock(&indio_dev->mlock);
+
+             if (iio_buffer_enabled(indio_dev)) {
+                     ret = -EBUSY;
+                     goto error_busy;
+             }
+
+             switch (chan->type) {
+             case IIO_TEMP:
+                     ret = regmap_bulk_read(data->regmap, chan->address,
+                                           (u8 *) &reg, sizeof(reg));
+                     break;
+             case IIO_PH:
+                     ret = atlas_read_ph_measurement(data, &reg);
+                     break;
+             default:
+                     ret = -EINVAL;
+             }
+
+             if (!ret) {
+                     *val = be32_to_cpu(reg);
+                     ret = IIO_VAL_INT;
+             }
+error_busy:
+             mutex_unlock(&indio_dev->mlock);
+             return ret;
+     }
+     case IIO_CHAN_INFO_SCALE:
+             *val = 0; /* 0.001 */
+             *val2 = 1000;
+             return IIO_VAL_INT_PLUS_MICRO;
+     }
+
+     return -EINVAL;
+}
+
+static int atlas_write_raw(struct iio_dev *indio_dev,
+                        struct iio_chan_spec const *chan,
Quoted 8 lines

drivers/iio/chemical/atlas-ph-sensor.c line 292

Quoted 6 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +6 -0
+                        int val, int val2, long mask)
+{
+     struct atlas_data *data = iio_priv(indio_dev);
+     __be32 reg = cpu_to_be32(val);
+
+     if (val2 > 0 || val < 0 || val > 20000)

probably clearer to check val2 != 0

Noted.

Quoted 9 lines

drivers/iio/chemical/atlas-ph-sensor.c line 298

Quoted 7 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +6 -0
+             return -EINVAL;
+
+     if (mask != IIO_CHAN_INFO_RAW || chan->type != IIO_TEMP)
+             return -EINVAL;
+
+     return regmap_bulk_write(data->regmap, chan->address, &reg, 4);

everywhere else sizeof(__be32) instead of 4

Will make this one or the other in v5

Quoted 24 lines
Quoted 11 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +10 -0
+}
+
+static const struct iio_info atlas_info = {
+     .driver_module = THIS_MODULE,
+     .read_raw = atlas_read_raw,
+     .write_raw = atlas_write_raw,
+};
+
+static int atlas_check_calibration(struct atlas_data *data)
+{

drivers/iio/chemical/atlas-ph-sensor.c line 318

Quoted 10 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +10 -0
+     struct device *dev = &data->client->dev;
+     int ret;
+     unsigned int val;
+
+     ret = regmap_read(data->regmap, ATLAS_REG_CALIB_STATUS, &val);
+     if (ret)
+             return ret;
+
+     if (!(val & ATLAS_REG_CALIB_STATUS_MASK)) {
+             dev_warn(dev, "device has not been calibrated");

\n at the end

Quoted 3 lines

drivers/iio/chemical/atlas-ph-sensor.c line 319

Quoted 1 line
drivers/iio/chemical/atlas-ph-sensor.c new file +1 -0
+             return 0;

maybe an error code here?

Not sure we want to error out just because there is no calibration data. Will think this over.

Quoted 196 lines
Quoted 87 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +86 -0
+     }
+
+     if (!(val & ATLAS_REG_CALIB_STATUS_LOW))
+             dev_warn(dev, "device missing low point calibration");
+
+     if (!(val & ATLAS_REG_CALIB_STATUS_MID))
+             dev_warn(dev, "device missing mid point calibration");
+
+     if (!(val & ATLAS_REG_CALIB_STATUS_HIGH))
+             dev_warn(dev, "device missing high point calibration");
+
+     return 0;
+};
+
+static int atlas_probe(struct i2c_client *client,
+                    const struct i2c_device_id *id)
+{
+     struct atlas_data *data;
+     struct iio_trigger *trig;
+     struct iio_dev *indio_dev;
+     int ret;
+
+     indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
+     if (!indio_dev)
+             return -ENOMEM;
+
+     indio_dev->info = &atlas_info;
+     indio_dev->name = ATLAS_DRV_NAME;
+     indio_dev->channels = atlas_channels;
+     indio_dev->num_channels = ARRAY_SIZE(atlas_channels);
+     indio_dev->modes = INDIO_BUFFER_SOFTWARE | INDIO_DIRECT_MODE;
+     indio_dev->dev.parent = &client->dev;
+
+     trig = devm_iio_trigger_alloc(&client->dev, "%s-dev%d",
+                                   indio_dev->name, indio_dev->id);
+
+     if (!trig)
+             return -ENOMEM;
+
+     data = iio_priv(indio_dev);
+     data->client = client;
+     data->trig = trig;
+     trig->dev.parent = indio_dev->dev.parent;
+     trig->ops = &atlas_interrupt_trigger_ops;
+     iio_trigger_set_drvdata(trig, indio_dev);
+
+     i2c_set_clientdata(client, indio_dev);
+
+     data->regmap = devm_regmap_init_i2c(client, &atlas_regmap_config);
+     if (IS_ERR(data->regmap)) {
+             dev_err(&client->dev, "regmap initialization failed\n");
+             return PTR_ERR(data->regmap);
+     }
+
+     ret = pm_runtime_set_active(&client->dev);
+     if (ret)
+             return ret;
+
+     if (client->irq <= 0) {
+             dev_err(&client->dev, "no valid irq defined\n");
+             return -EINVAL;
+     }
+
+     ret = atlas_check_calibration(data);
+     if (ret)
+             return ret;
+
+     ret = iio_trigger_register(trig);
+     if (ret) {
+             dev_err(&client->dev, "failed to register trigger\n");
+             return ret;
+     }
+
+     ret = iio_triggered_buffer_setup(indio_dev, &iio_pollfunc_store_time,
+             &atlas_trigger_handler, &atlas_buffer_setup_ops);
+     if (ret) {
+             dev_err(&client->dev, "cannot setup iio trigger\n");
+             goto unregister_trigger;
+     }
+
+     init_irq_work(&data->work, atlas_work_handler);
+
+     ret = devm_request_threaded_irq(&client->dev, client->irq,
+                                     NULL, atlas_interrupt_handler,
+                                     IRQF_TRIGGER_RISING |
+                                     IRQF_TRIGGER_FALLING | IRQF_ONESHOT,

drivers/iio/chemical/atlas-ph-sensor.c line 415

Quoted 10 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +10 -0
+                                     "atlas_irq",
+                                     indio_dev);
+     if (ret) {
+             dev_err(&client->dev, "request irq (%d) failed\n", client->irq);
+             goto unregister_buffer;
+     }
+
+     ret = atlas_set_powermode(data, 1);
+     if (ret) {
+             dev_err(&client->dev, "cannot power device on");

\n

Quoted 81 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +80 -0
+             goto unregister_buffer;
+     }
+
+     pm_runtime_enable(&client->dev);
+     pm_runtime_set_autosuspend_delay(&client->dev, 2500);
+     pm_runtime_use_autosuspend(&client->dev);
+
+     ret = iio_device_register(indio_dev);
+     if (ret) {
+             dev_err(&client->dev, "unable to register device\n");
+             goto unregister_buffer;
+     }
+
+     return 0;
+
+unregister_buffer:
+     iio_triggered_buffer_cleanup(indio_dev);
+
+unregister_trigger:
+     iio_trigger_unregister(data->trig);
+
+     return ret;
+}
+
+static int atlas_remove(struct i2c_client *client)
+{
+     struct iio_dev *indio_dev = i2c_get_clientdata(client);
+     struct atlas_data *data = iio_priv(indio_dev);
+
+     iio_device_unregister(indio_dev);
+     iio_triggered_buffer_cleanup(indio_dev);
+     iio_trigger_unregister(data->trig);
+
+     pm_runtime_disable(&client->dev);
+     pm_runtime_set_suspended(&client->dev);
+     pm_runtime_put_noidle(&client->dev);
+
+     return atlas_set_powermode(data, 0);
+}
+
+#ifdef CONFIG_PM
+static int atlas_runtime_suspend(struct device *dev)
+{
+     struct atlas_data *data =
+                  iio_priv(i2c_get_clientdata(to_i2c_client(dev)));
+
+     return atlas_set_powermode(data, 0);
+}
+
+static int atlas_runtime_resume(struct device *dev)
+{
+     struct atlas_data *data =
+                  iio_priv(i2c_get_clientdata(to_i2c_client(dev)));
+
+     return atlas_set_powermode(data, 1);
+}
+#endif
+
+static const struct dev_pm_ops atlas_pm_ops = {
+     SET_RUNTIME_PM_OPS(atlas_runtime_suspend,
+                        atlas_runtime_resume, NULL)
+};
+
+static const struct i2c_device_id atlas_id[] = {
+     { "atlas-ph-sm", 0 },
+     {}
+};
+MODULE_DEVICE_TABLE(i2c, atlas_id);
+
+static const struct of_device_id atlas_dt_ids[] = {
+     { .compatible = "atlas,ph-sm" },
+     { }
+};
+MODULE_DEVICE_TABLE(of, atlas_dt_ids);
+
+static struct i2c_driver atlas_driver = {
+     .driver = {
+             .name   = ATLAS_DRV_NAME,
+             .of_match_table = of_match_ptr(atlas_dt_ids),
+             .pm     = &atlas_pm_ops,

drivers/iio/chemical/atlas-ph-sensor.c line 505

Quoted 10 lines
drivers/iio/chemical/atlas-ph-sensor.c new file +10 -0
+     },
+     .probe          = atlas_probe,
+     .remove         = atlas_remove,
+     .id_table       = atlas_id,
+};
+module_i2c_driver(atlas_driver);
+
+MODULE_AUTHOR("Matt Ranostay <[email protected]>");
+MODULE_DESCRIPTION("Atlas Scientific pH-SM sensor");
+MODULE_LICENSE("GPL");

--

Peter Meerwald-Stadler
+43-664-2444418 (mobile)