Skip to contentSkip to conversation

ath9k: make NF load complete quickly and reliably

PATCH Applied [email protected] 3 participants 3 messages Feb 5, 2016 – Mar 4, 2016 Qualcomm Atheros ATH9K wireless driver

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 ath9k: make NF load complete quickly and reliably

From: Miaoqing Pan <[email protected]>

Make NF load complete quickly and reliably. NF load execution is delayed by HW to end of frame if frame Rx or Tx is ongoing. Increasing timeout to max frame duration. If NF cal is ongoing before NF load, stop it before load, and restart it afterwards.

---
 drivers/net/wireless/ath/ath9k/calib.c | 38 ++++++++++++++++++++++++++++------
 1 file changed, 32 insertions(+), 6 deletions(-)
drivers/net/wireless/ath/ath9k/calib.c +32 -6
index 3e2e24e..37f6d66 100644
@@ -241,6 +241,7 @@ int ath9k_hw_loadnf(struct ath_hw *ah, struct ath9k_channel *chan)
 	u8 chainmask = (ah->rxchainmask << 3) | ah->rxchainmask;
 	struct ath_common *common = ath9k_hw_common(ah);
 	s16 default_nf = ath9k_hw_get_default_nf(ah, chan);
+	u32 bb_agc_ctl = REG_READ(ah, AR_PHY_AGC_CONTROL);
 
 	if (ah->caldata)
 		h = ah->caldata->nfCalHist;
@@ -264,6 +265,16 @@ int ath9k_hw_loadnf(struct ath_hw *ah, struct ath9k_channel *chan)
 	}
 
 	/*
+	 * stop NF cal if ongoing to ensure NF load completes immediately
+	 * (or after end rx/tx frame if ongoing)
+	 */
+	if (bb_agc_ctl & AR_PHY_AGC_CONTROL_NF) {
+		REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);
+		REG_RMW_BUFFER_FLUSH(ah);
+		ENABLE_REG_RMW_BUFFER(ah);
+	}
+
+	/*
 	 * Load software filtered NF value into baseband internal minCCApwr
 	 * variable.
 	 */
@@ -276,18 +287,33 @@ int ath9k_hw_loadnf(struct ath_hw *ah, struct ath9k_channel *chan)
 
 	/*
 	 * Wait for load to complete, should be fast, a few 10s of us.
-	 * The max delay was changed from an original 250us to 10000us
-	 * since 250us often results in NF load timeout and causes deaf
-	 * condition during stress testing 12/12/2009
+	 * The max delay was changed from an original 250us to 22.2 msec.
+	 * This would increase timeout to the longest possible frame
+	 * (11n max length 22.1 msec)
 	 */
-	for (j = 0; j < 10000; j++) {
+	for (j = 0; j < 22200; j++) {
 		if ((REG_READ(ah, AR_PHY_AGC_CONTROL) &
-		     AR_PHY_AGC_CONTROL_NF) == 0)
+			      AR_PHY_AGC_CONTROL_NF) == 0)
 			break;
 		udelay(10);
 	}
 
 	/*
+	 * Restart NF so it can continue.
+	 */
+	if (bb_agc_ctl & AR_PHY_AGC_CONTROL_NF) {
+		ENABLE_REG_RMW_BUFFER(ah);
+		if (bb_agc_ctl & AR_PHY_AGC_CONTROL_ENABLE_NF)
+			REG_SET_BIT(ah, AR_PHY_AGC_CONTROL,
+				    AR_PHY_AGC_CONTROL_ENABLE_NF);
+		if (bb_agc_ctl & AR_PHY_AGC_CONTROL_NO_UPDATE_NF)
+			REG_SET_BIT(ah, AR_PHY_AGC_CONTROL,
+				    AR_PHY_AGC_CONTROL_NO_UPDATE_NF);
+		REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);
+		REG_RMW_BUFFER_FLUSH(ah);
+	}
+
+	/*
 	 * We timed out waiting for the noisefloor to load, probably due to an
 	 * in-progress rx. Simply return here and allow the load plenty of time
 	 * to complete before the next calibration interval.  We need to avoid
@@ -296,7 +322,7 @@ int ath9k_hw_loadnf(struct ath_hw *ah, struct ath9k_channel *chan)
 	 * here, the baseband nf cal will just be capped by our present
 	 * noisefloor until the next calibration timer.
 	 */
-	if (j == 10000) {
+	if (j == 22200) {
 		ath_dbg(common, ANY,
 			"Timeout while waiting for nf to load: AR_PHY_AGC_CONTROL=0x%x\n",
 			REG_READ(ah, AR_PHY_AGC_CONTROL));
Signature · 1 line
1.9.1
#1 lore raw

Hi Miaoqing,

Quoted 11 lines · On Fri, Feb 5, 2016 at 12:45 PM, <[email protected]> wrote:

From: Miaoqing Pan <[email protected]>

Make NF load complete quickly and reliably. NF load execution is delayed by HW to end of frame if frame Rx or Tx is ongoing. Increasing timeout to max frame duration. If NF cal is ongoing before NF load, stop it before load, and restart it afterwards.

---
 drivers/net/wireless/ath/ath9k/calib.c | 38 ++++++++++++++++++++++++++++------
 1 file changed, 32 insertions(+), 6 deletions(-)

You should add a changelog here so people know what's changed in this version of the patch.

Thanks,

Signature · 4 lines
Julian Calaby

Email: [email protected]
Profile: http://www.google.com/profiles/julian.calaby/
Applied
#2 lore raw
In reply to [email protected]
Quoted 8 lines · [email protected] writes:

From: Miaoqing Pan <[email protected]>

Make NF load complete quickly and reliably. NF load execution is delayed by HW to end of frame if frame Rx or Tx is ongoing. Increasing timeout to max frame duration. If NF cal is ongoing before NF load, stop it before load, and restart it afterwards.

Applied to ath.git, thanks.

Signature · 1 line
Kalle Valo