auxdisplay: ht16k33: Driver for LED controller.
Subsystems (5)
Robin van der Gracht
maintainerPATCH v3 1/1 auxdisplay: ht16k33: Driver for LED controller.
This is a driver for the Holtek HT16K33 LED controller with keyscan.
Signed-off-by Robin van der Gracht <robin-/Q/[email protected]>
---
Changes in v3:
- Renamed device-tree property 'refresh-rate' to 'refresh-rate-hz'
- Renamed device-tree property 'default-brightness' to 'default-brightness-level'
- Realligned the strings in the documentation (ht16k33.txt).
.../devicetree/bindings/display/ht16k33.txt | 42 ++ drivers/auxdisplay/Kconfig | 9 + drivers/auxdisplay/Makefile | 1 + drivers/auxdisplay/ht16k33.c | 574 +++++++++++++++++++++ 4 files changed, 626 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/ht16k33.txt create mode 100644 drivers/auxdisplay/ht16k33.c
Documentation/devicetree/bindings/display/ht16k33.txt new file +42 -0
@@ -0,0 +1,42 @@ +Holtek ht16k33 RAM mapping 16*8 LED controller driver with keyscan +------------------------------------------------------------------------------- + +Required properties: +- compatible: "ht,ht16k33" +- reg: I2C slave address of the chip. +- interrupt-parent: A phandle pointing to the interrupt controller\ + serving the interrupt for this chip. +- interrupts: Interrupt specification for the key pressed interrupt. +- refresh-rate-hz: Display update interval in HZ. +- debounce-delay-ms: Debouncing interval time in microseconds. +- linux,keymap: The keymap for keys as described in the binding + document (devicetree/bindings/input/matrix-keymap.txt). + +Optional properties: +- linux,no-autorepeat: Disable keyrepeat. +- default-brightness-level: Initial brightness level [0-15] (default: 15). + +Example: + +&i2c1 { + ht16k33: ht16k33@70 { + compatible = "ht,ht16k33"; + reg = <0x70>; + refresh-rate-hz = <20>; + debounce-delay-ms = <50>; + interrupt-parent = <&gpio4>; + interrupts = <5 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>; + linux,keymap = < + MATRIX_KEY(2, 0, KEY_F6) + MATRIX_KEY(3, 0, KEY_F8) + MATRIX_KEY(4, 0, KEY_F0) + MATRIX_KEY(5, 0, KEY_F4) + MATRIX_KEY(6, 0, KEY_F2) + MATRIX_KEY(2, 1, KEY_F5) + MATRIX_KEY(3, 1, KEY_F7) + MATRIX_KEY(4, 1, KEY_F9) + MATRIX_KEY(5, 1, KEY_F3) + MATRIX_KEY(6, 1, KEY_F1) + >; + }; +};
drivers/auxdisplay/Kconfig +9 -0
@@ -119,4 +119,13 @@ config CFAG12864B_RATE If you compile this as a module, you can still override this value using the module parameters. +config HT16K33 + tristate "Holtek Ht16K33 LED controller with keyscan" + depends on FB && OF && I2C && INPUT + select INPUT_MATRIXKMAP + select FB_BACKLIGHT + help + Say yes here to add support for Holtek HT16K33, RAM mapping 16*8 + LED controller driver with keyscan. + endif # AUXDISPLAY
drivers/auxdisplay/Makefile +1 -0
@@ -4,3 +4,4 @@ obj-$(CONFIG_KS0108) += ks0108.o obj-$(CONFIG_CFAG12864B) += cfag12864b.o cfag12864bfb.o +obj-$(CONFIG_HT16K33) += ht16k33.o
drivers/auxdisplay/ht16k33.c new file +574 -0
574 lines not on this page · raw message
Signature · 6 lines
2.5.0 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 10 lines · Robin van der Gracht
This is a driver for the Holtek HT16K33 LED controller with keyscan.
Signed-off-by Robin van der Gracht <[email protected]>---
Changes in v3:
- Renamed device-tree property 'refresh-rate' to 'refresh-rate-hz'
- Renamed device-tree property 'default-brightness' to 'default-brightness-level'
- Realligned the strings in the documentation (ht16k33.txt)..../devicetree/bindings/display/ht16k33.txt | 42 ++
Acked-by Rob Herring <[email protected]>
Quoted 6 lines
drivers/auxdisplay/Kconfig | 9 + drivers/auxdisplay/Makefile | 1 + drivers/auxdisplay/ht16k33.c | 574 +++++++++++++++++++++ 4 files changed, 626 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/ht16k33.txt create mode 100644 drivers/auxdisplay/ht16k33.c