Support for analog peripherals on LPC18xx familiy
Subsystems (3)
cover Support for analog peripherals on LPC18xx familiy
This patch set adds support for the analog (ADC and DAC) peripherals found on NXP LPC18xx/43xx SoCs. The ADC is a SAR converter with 10-bit resolution and 8 muxed inputs. The DAC is a simple single channel 10- bit DAC.
Note that these drivers do not support all the features found on the peripherals. DMA and interrupts are not supported in either drivers. The ADC driver also lack 'burst-mode' and hardware triggers. So for now the ADC is limited to single shot samples.
Both drivers tested on Embedded Artists' LPC4357 Developer's Kit.
Based on iio/testing branch from 29.02.15.
Joachim Eastwood (4):
iio: adc: add NXP LPC18xx ADC driver
dt: document NXP LPC1850 ADC driver bindings
iio: dac: add NXP LPC18xx DAC driver
dt: document NXP LPC1850 DAC driver bindings
.../devicetree/bindings/iio/adc/lpc1850-adc.txt | 21 ++ .../devicetree/bindings/iio/dac/lpc1850-dac.txt | 20 ++ drivers/iio/adc/Kconfig | 10 + drivers/iio/adc/Makefile | 1 + drivers/iio/adc/lpc18xx_adc.c | 226 +++++++++++++++++++++ drivers/iio/dac/Kconfig | 10 + drivers/iio/dac/Makefile | 1 + drivers/iio/dac/lpc18xx_dac.c | 204 +++++++++++++++++++ 8 files changed, 493 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/adc/lpc1850-adc.txt create mode 100644 Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt create mode 100644 drivers/iio/adc/lpc18xx_adc.c create mode 100644 drivers/iio/dac/lpc18xx_dac.c
Signature · 1 line
1.8.0
PATCH 1/4 iio: adc: add NXP LPC18xx ADC driver
Add base support for the 10-bit SAR ADC peripheral found on NXP LPC18xx/43xx SoCs.
This is a minimal driver that does not support burst mode, interrupts, DMA or hardware triggers.
User manual with register description can be found on:
LPC18xx: www.nxp.com/documents/user_manual/UM10430.pdf
LPC43xx: www.nxp.com/documents/user_manual/UM10503.pdf
--- drivers/iio/adc/Kconfig | 10 ++ drivers/iio/adc/Makefile | 1 + drivers/iio/adc/lpc18xx_adc.c | 226 ++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 237 insertions(+) create mode 100644 drivers/iio/adc/lpc18xx_adc.c
drivers/iio/adc/Kconfig +10 -0
@@ -234,6 +234,16 @@ config LP8788_ADC To compile this driver as a module, choose M here: the module will be called lp8788_adc. +config LPC18XX_ADC + tristate "NXP LPC18xx ADC driver" + depends on ARCH_LPC18XX || COMPILE_TEST + depends on OF && HAS_IOMEM + help + Say yes here to build support for NXP LPC18XX ADC. + + To compile this driver as a module, choose M here: the module will be + called lpc18xx_adc. + config MAX1027 tristate "Maxim max1027 ADC driver" depends on SPI
drivers/iio/adc/Makefile +1 -0
@@ -24,6 +24,7 @@ obj-$(CONFIG_HI8435) += hi8435.o obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o obj-$(CONFIG_INA2XX_ADC) += ina2xx-adc.o obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o +obj-$(CONFIG_LPC18XX_ADC) += lpc18xx_adc.o obj-$(CONFIG_MAX1027) += max1027.o obj-$(CONFIG_MAX1363) += max1363.o obj-$(CONFIG_MCP320X) += mcp320x.o
drivers/iio/adc/lpc18xx_adc.c new file +226 -0
226 lines not on this page · raw message
Signature · 1 line
1.8.0
Re: [PATCH 1/4] iio: adc: add NXP LPC18xx ADC driver
Quoted 3 lines
Add base support for the 10-bit SAR ADC peripheral found on NXP LPC18xx/43xx SoCs.
nitpicking below
Quoted 80 lines
This is a minimal driver that does not support burst mode, interrupts, DMA or hardware triggers.
User manual with register description can be found on:
LPC18xx: www.nxp.com/documents/user_manual/UM10430.pdf
LPC43xx: www.nxp.com/documents/user_manual/UM10503.pdfSigned-off-by Joachim Eastwood <[email protected]>--- drivers/iio/adc/Kconfig | 10 ++ drivers/iio/adc/Makefile | 1 + drivers/iio/adc/lpc18xx_adc.c | 226 ++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 237 insertions(+) create mode 100644 drivers/iio/adc/lpc18xx_adc.cdrivers/iio/adc/Kconfig +10
-0@@ -234,6 +234,16 @@ config LP8788_ADC To compile this driver as a module, choose M here: the module will be called lp8788_adc. +config LPC18XX_ADC + tristate "NXP LPC18xx ADC driver" + depends on ARCH_LPC18XX || COMPILE_TEST + depends on OF && HAS_IOMEM + help + Say yes here to build support for NXP LPC18XX ADC. + + To compile this driver as a module, choose M here: the module will be + called lpc18xx_adc. + config MAX1027 tristate "Maxim max1027 ADC driver" depends on SPIdrivers/iio/adc/Makefile +1
-0@@ -24,6 +24,7 @@ obj-$(CONFIG_HI8435) += hi8435.o obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o obj-$(CONFIG_INA2XX_ADC) += ina2xx-adc.o obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o +obj-$(CONFIG_LPC18XX_ADC) += lpc18xx_adc.o obj-$(CONFIG_MAX1027) += max1027.o obj-$(CONFIG_MAX1363) += max1363.o obj-$(CONFIG_MCP320X) += mcp320x.odrivers/iio/adc/lpc18xx_adc.c new file +26
-0@@ -0,0 +1,226 @@ +/* +* IIO ADC driver for NXP LPC18xx ADC +* +* Copyright (C) 2016 Joachim Eastwood <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +* +* UNSUPPORTED hardware features: +* - Hardware triggers +* - Burst mode +* - Interrupts +* - DMA +*/ + +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/iio/iio.h> +#include <linux/iio/driver.h> +#include <linux/io.h> +#include <linux/iopoll.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/platform_device.h>
drivers/iio/adc/lpc18xx_adc.c line 36
Quoted 10 lines
drivers/iio/adc/lpc18xx_adc.c new file +10
-0+#include <linux/regulator/consumer.h> + +/* LPC18XX ADC registers and bits */ +#define LPC18XX_ADC_CR 0x000 +#define LPC18XX_ADC_CR_CLKDIV_SHIFT 8 +#define LPC18XX_ADC_CR_PDN BIT(21) +#define LPC18XX_ADC_CR_START_NOW (0x1 << 24) +#define LPC18XX_ADC_GDR 0x004 + +/* Data registers bits */
'Data register bits' maybe
Quoted 105 lines
drivers/iio/adc/lpc18xx_adc.c new file +105
-0+#define LPC18XX_ADC_SAMPLE_SHIFT 6 +#define LPC18XX_ADC_SAMPLE_MASK 0x3ff +#define LPC18XX_ADC_CONV_DONE BIT(31) + +/* Clock should be 4.5 MHz or less */ +#define LPC18XX_ADC_CLK_TARGET 4500000 + +struct lpc18xx_adc { +void __iomem *base; +struct device *dev; +struct clk *clk; +struct regulator *vref; +u32 cr_reg; +}; + +#define LPC18XX_ADC_CHAN (_idx) { \ + .type = IIO_VOLTAGE, \ + .indexed = 1, \ + .channel = _idx, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ +} + +static const struct iio_chan_spec lpc18xx_adc_iio_channels[] = { +LPC18XX_ADC_CHAN (0 ), +LPC18XX_ADC_CHAN (1 ), +LPC18XX_ADC_CHAN (2 ), +LPC18XX_ADC_CHAN (3 ), +LPC18XX_ADC_CHAN (4 ), +LPC18XX_ADC_CHAN (5 ), +LPC18XX_ADC_CHAN (6 ), +LPC18XX_ADC_CHAN (7 ), +}; + +static int lpc18xx_adc_read_chan (struct lpc18xx_adc *adc,unsigned int ch) +{ +int ret; +u32 reg; + + reg = adc->cr_reg |BIT (ch) |LPC18XX_ADC_CR_START_NOW ; +writel (reg, adc->base +LPC18XX_ADC_CR ); + + ret =readl_poll_timeout (adc->base +LPC18XX_ADC_GDR , reg, + reg &LPC18XX_ADC_CONV_DONE ,3 ,9 ); +if (ret) { +dev_warn (adc->dev,"adc read timed out\n" ); +return ret; + } + +return (reg >>LPC18XX_ADC_SAMPLE_SHIFT ) &LPC18XX_ADC_SAMPLE_MASK ; +} + +static int lpc18xx_adc_read_raw (struct iio_dev *indio_dev, +struct iio_chan_spec const *chan, +int *val,int *val2,long mask) +{ +struct lpc18xx_adc *adc =iio_priv (indio_dev); + +switch (mask) { +case IIO_CHAN_INFO_RAW : + *val =lpc18xx_adc_read_chan (adc, chan->channel); +if (*val <0 ) +return *val; + +return IIO_VAL_INT ; + +case IIO_CHAN_INFO_SCALE : + *val =regulator_get_voltage (adc->vref) /1000 ; + *val2 =10 ; + +return IIO_VAL_FRACTIONAL_LOG2 ; + } + +return -EINVAL ; +} + +static const struct iio_info lpc18xx_adc_info = { + .read_raw = lpc18xx_adc_read_raw, + .driver_module =THIS_MODULE , +}; + +static int lpc18xx_adc_probe (struct platform_device *pdev) +{ +struct iio_dev *indio_dev; +struct lpc18xx_adc *adc; +struct resource *res; +unsigned int clkdiv; +unsigned long rate; +int ret; + + indio_dev =devm_iio_device_alloc (&pdev->dev,sizeof (*adc)); +if (!indio_dev) +return -ENOMEM ; + +platform_set_drvdata (pdev, indio_dev); + adc =iio_priv (indio_dev); + adc->dev = &pdev->dev; + + res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); + adc->base =devm_ioremap_resource (&pdev->dev, res); +if (IS_ERR (adc->base)) +return PTR_ERR (adc->base); + + adc->clk =devm_clk_get (&pdev->dev,NULL ); +if (IS_ERR (adc->clk)) {
drivers/iio/adc/lpc18xx_adc.c line 151
Quoted 10 lines
drivers/iio/adc/lpc18xx_adc.c new file +10
-0+dev_err (&pdev->dev,"error getting clock\n" ); +return PTR_ERR (adc->clk); + } + + rate =clk_get_rate (adc->clk); + clkdiv =DIV_ROUND_UP (rate,LPC18XX_ADC_CLK_TARGET ); + + adc->vref =devm_regulator_get (&pdev->dev,"vref" ); +if (IS_ERR (adc->vref)) { +dev_err (&pdev->dev,"error get regulator\n" );
getting
Quoted 9 lines
drivers/iio/adc/lpc18xx_adc.c new file +9
-0+return PTR_ERR (adc->vref); + } + + indio_dev->name =dev_name (&pdev->dev); + indio_dev->dev.parent = &pdev->dev; + indio_dev->info = &lpc18xx_adc_info; + indio_dev->modes =INDIO_DIRECT_MODE ; + indio_dev->channels = lpc18xx_adc_iio_channels; + indio_dev->num_channels =ARRAY_SIZE (lpc18xx_adc_iio_channels);
drivers/iio/adc/lpc18xx_adc.c line 170
Quoted 10 lines
drivers/iio/adc/lpc18xx_adc.c new file +10
-0+ + ret =regulator_enable (adc->vref); +if (ret) { +dev_err (&pdev->dev,"unable to enable regulator\n" ); +return ret; + } + + ret =clk_prepare_enable (adc->clk); +if (ret) { +dev_err (&pdev->dev,"unable to enable clock.\n" );
maybe delete '.', it's the only message with a full stop
Quoted 57 lines
drivers/iio/adc/lpc18xx_adc.c new file +56
-0+ goto dis_reg; + } + + adc->cr_reg = (clkdiv <<LPC18XX_ADC_CR_CLKDIV_SHIFT ) | +LPC18XX_ADC_CR_PDN ; +writel (adc->cr_reg, adc->base +LPC18XX_ADC_CR ); + + ret =iio_device_register (indio_dev); +if (ret) { +dev_err (&pdev->dev,"unable to register device\n" ); + goto dis_clk; + } + +return 0 ; + +dis_clk: +writel (0 , adc->base +LPC18XX_ADC_CR ); +clk_disable_unprepare (adc->clk); +dis_reg: +regulator_disable (adc->vref); +return ret; +} + +static int lpc18xx_adc_remove (struct platform_device *pdev) +{ +struct iio_dev *indio_dev =platform_get_drvdata (pdev); +struct lpc18xx_adc *adc =iio_priv (indio_dev); + +iio_device_unregister (indio_dev); + +writel (0 , adc->base +LPC18XX_ADC_CR ); +clk_disable_unprepare (adc->clk); +regulator_disable (adc->vref); + +return 0 ; +} + +static const struct of_device_id lpc18xx_adc_match[] = { + { .compatible ="nxp,lpc1850-adc" }, + {/* sentinel */ } +}; +MODULE_DEVICE_TABLE (of, lpc18xx_adc_match); + +static struct platform_driver lpc18xx_adc_driver = { + .probe = lpc18xx_adc_probe, + .remove = lpc18xx_adc_remove, + .driver = { + .name ="lpc18xx-adc" , + .of_match_table = lpc18xx_adc_match, + }, +}; +module_platform_driver (lpc18xx_adc_driver); + +MODULE_DESCRIPTION ("LPC18xx ADC driver" ); +MODULE_AUTHOR ("Joachim Eastwood <[email protected]>" ); +MODULE_LICENSE ("GPL v2" );
Signature · 2 lines
Peter Meerwald-Stadler +43-664-2444418 (mobile)
Re: [PATCH 1/4] iio: adc: add NXP LPC18xx ADC driver
Hi Peter,
Quoted 38 lines · Peter Meerwald-Stadler
Quoted 3 lines
Add base support for the 10-bit SAR ADC peripheral found on NXP LPC18xx/43xx SoCs.
nitpicking below
Quoted 10 lines
This is a minimal driver that does not support burst mode, interrupts, DMA or hardware triggers.
User manual with register description can be found on:
LPC18xx: www.nxp.com/documents/user_manual/UM10430.pdf
LPC43xx: www.nxp.com/documents/user_manual/UM10503.pdfSigned-off-by Joachim Eastwood <[email protected]>---
+/* Data registers bits */'Data register bits' maybe
drivers/iio/adc/lpc18xx_adc.c line 151
Quoted 3 lines
drivers/iio/adc/lpc18xx_adc.c new file +3
-0+ adc->vref =devm_regulator_get (&pdev->dev,"vref" ); +if (IS_ERR (adc->vref)) { +dev_err (&pdev->dev,"error get regulator\n" );getting
Quoted 13 lines
drivers/iio/adc/lpc18xx_adc.c new file +13
-0+return PTR_ERR (adc->vref); + } + + indio_dev->name =dev_name (&pdev->dev); + indio_dev->dev.parent = &pdev->dev; + indio_dev->info = &lpc18xx_adc_info; + indio_dev->modes =INDIO_DIRECT_MODE ; + indio_dev->channels = lpc18xx_adc_iio_channels; + indio_dev->num_channels =ARRAY_SIZE (lpc18xx_adc_iio_channels); + + ret =regulator_enable (adc->vref); +if (ret) { +dev_err (&pdev->dev,"unable to enable regulator\n" );
Quoted 8 lines
drivers/iio/adc/lpc18xx_adc.c line 170
Quoted 6 lines
drivers/iio/adc/lpc18xx_adc.c new file +6
-0+return ret; + } + + ret =clk_prepare_enable (adc->clk); +if (ret) { +dev_err (&pdev->dev,"unable to enable clock.\n" );maybe delete '.', it's the only message with a full stop
I will fix them all in the next version. I also noticed that a couple of your comments also apply to the dac driver.
Thanks for looking through!
regards,
Joachim Eastwood
PATCH 2/4 dt: document NXP LPC1850 ADC driver bindings
In reply to Joachim Eastwood--- .../devicetree/bindings/iio/adc/lpc1850-adc.txt | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/adc/lpc1850-adc.txt
Documentation/devicetree/bindings/iio/adc/lpc1850-adc.txt new file +21 -0
@@ -0,0 +1,21 @@ +NXP LPC1850 ADC bindings + +Required properties: +- compatible: Should be "nxp,lpc1850-adc" +- reg: Offset and length of the register set for the ADC device +- interrupts: The interrupt number for the ADC device +- clocks: The root clock of the ADC controller +- vref-supply: The regulator supply ADC reference voltage +- resets: phandle to reset controller and line specifier + +Example: + +adc0: adc@400e3000 { + compatible = "nxp,lpc1850-adc"; + reg = <0x400e3000 0x1000>; + interrupts = <17>; + clocks = <&ccu1 CLK_APB3_ADC0>; + vref-supply = <®_vdda>; + resets = <&rgu 40>; + status = "disabled"; +};
Signature · 1 line
1.8.0
PATCH 3/4 iio: dac: add NXP LPC18xx DAC driver
In reply to Joachim EastwoodAdd base support for the 10-bit DAC peripheral found on NXP LPC18xx/43xx SoCs.
This is a minimal driver that does not support DMA or interrupts.
User manual with register description can be found on:
LPC18xx: www.nxp.com/documents/user_manual/UM10430.pdf
LPC43xx: www.nxp.com/documents/user_manual/UM10503.pdf
--- drivers/iio/dac/Kconfig | 10 +++ drivers/iio/dac/Makefile | 1 + drivers/iio/dac/lpc18xx_dac.c | 204 ++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 215 insertions(+) create mode 100644 drivers/iio/dac/lpc18xx_dac.c
drivers/iio/dac/Kconfig +10 -0
@@ -154,6 +154,16 @@ config AD7303 To compile this driver as module choose M here: the module will be called ad7303. +config LPC18XX_DAC + tristate "NXP LPC18xx DAC driver" + depends on ARCH_LPC18XX || COMPILE_TEST + depends on OF && HAS_IOMEM + help + Say yes here to build support for NXP LPC18XX DAC. + + To compile this driver as a module, choose M here: the module will be + called lpc18xx_dac. + config M62332 tristate "Mitsubishi M62332 DAC driver" depends on I2C
drivers/iio/dac/Makefile +1 -0
@@ -17,6 +17,7 @@ obj-$(CONFIG_AD5764) += ad5764.o obj-$(CONFIG_AD5791) += ad5791.o obj-$(CONFIG_AD5686) += ad5686.o obj-$(CONFIG_AD7303) += ad7303.o +obj-$(CONFIG_LPC18XX_DAC) += lpc18xx_dac.o obj-$(CONFIG_M62332) += m62332.o obj-$(CONFIG_MAX517) += max517.o obj-$(CONFIG_MAX5821) += max5821.o
drivers/iio/dac/lpc18xx_dac.c new file +204 -0
204 lines not on this page · raw message
Signature · 1 line
1.8.0
PATCH 4/4 dt: document NXP LPC1850 DAC driver bindings
In reply to Joachim Eastwood--- .../devicetree/bindings/iio/dac/lpc1850-dac.txt | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt
Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt new file +20 -0
@@ -0,0 +1,20 @@ +NXP LPC1850 DAC bindings + +Required properties: +- compatible: Should be "nxp,lpc1850-dac" +- reg: Offset and length of the register set for the ADC device +- interrupts: The interrupt number for the ADC device +- clocks: The root clock of the ADC controller +- vref-supply: The regulator supply ADC reference voltage +- resets: phandle to reset controller and line specifier + +Example: +dac: dac@400e1000 { + compatible = "nxp,lpc1850-dac"; + reg = <0x400e1000 0x1000>; + interrupts = <0>; + clocks = <&ccu1 CLK_APB3_DAC>; + vref-supply = <®_vdda>; + resets = <&rgu 42>; + status = "disabled"; +};
Signature · 1 line
1.8.0
Quoted 12 lines · Joachim Eastwood
This patch set adds support for the analog (ADC and DAC) peripherals found on NXP LPC18xx/43xx SoCs. The ADC is a SAR converter with 10-bit resolution and 8 muxed inputs. The DAC is a simple single channel 10- bit DAC.
Note that these drivers do not support all the features found on the peripherals. DMA and interrupts are not supported in either drivers. The ADC driver also lack 'burst-mode' and hardware triggers. So for now the ADC is limited to single shot samples.
Both drivers tested on Embedded Artists' LPC4357 Developer's Kit.
Quoted 8 lines
Based on iio/testing branch from 29.02.15.
Joachim Eastwood (4):
iio: adc: add NXP LPC18xx ADC driver
dt: document NXP LPC1850 ADC driver bindings
iio: dac: add NXP LPC18xx DAC driver
dt: document NXP LPC1850 DAC driver bindings
You need to send bindings to the DT list.
Rob
Hi Rob,
Quoted 16 lines · Rob Herring
Quoted 15 lines · Joachim Eastwood
This patch set adds support for the analog (ADC and DAC) peripherals found on NXP LPC18xx/43xx SoCs. The ADC is a SAR converter with 10-bit resolution and 8 muxed inputs. The DAC is a simple single channel 10- bit DAC.
Note that these drivers do not support all the features found on the peripherals. DMA and interrupts are not supported in either drivers. The ADC driver also lack 'burst-mode' and hardware triggers. So for now the ADC is limited to single shot samples.
Both drivers tested on Embedded Artists' LPC4357 Developer's Kit.
Based on iio/testing branch from 29.02.15.
Quoted 7 lines
Quoted 5 lines
Joachim Eastwood (4):
iio: adc: add NXP LPC18xx ADC driver
dt: document NXP LPC1850 ADC driver bindings
iio: dac: add NXP LPC18xx DAC driver
dt: document NXP LPC1850 DAC driver bindingsYou need to send bindings to the DT list.
ah, my bad. I was pretty sure I added it when I did format-patch, but it seems to have been lost along the way...
Either way there will be a v2 and I will make sure to cc the DT list then.
Thanks for reporting.
regards,
Joachim Eastwood
Jonathan Cameron
maintainerQuoted 5 lines · Joachim Eastwood
This patch set adds support for the analog (ADC and DAC) peripherals found on NXP LPC18xx/43xx SoCs. The ADC is a SAR converter with 10-bit resolution and 8 muxed inputs. The DAC is a simple single channel 10- bit DAC.
Quoted 8 lines
Note that these drivers do not support all the features found on the peripherals. DMA and interrupts are not supported in either drivers. The ADC driver also lack 'burst-mode' and hardware triggers. So for now the ADC is limited to single shot samples.
Both drivers tested on Embedded Artists' LPC4357 Developer's Kit.
Based on iio/testing branch from 29.02.15.
Series looks pretty good. Will do a review of V2 - right now I haven't found anything to add to what Peter found.
Nice little ADC from a quick read of the data sheet. Not too complex but still well featured.
Quoted 22 lines
Joachim Eastwood (4):
iio: adc: add NXP LPC18xx ADC driver
dt: document NXP LPC1850 ADC driver bindings
iio: dac: add NXP LPC18xx DAC driver
dt: document NXP LPC1850 DAC driver bindings.../devicetree/bindings/iio/adc/lpc1850-adc.txt | 21 ++ .../devicetree/bindings/iio/dac/lpc1850-dac.txt | 20 ++ drivers/iio/adc/Kconfig | 10 + drivers/iio/adc/Makefile | 1 + drivers/iio/adc/lpc18xx_adc.c | 226 +++++++++++++++++++++ drivers/iio/dac/Kconfig | 10 + drivers/iio/dac/Makefile | 1 + drivers/iio/dac/lpc18xx_dac.c | 204 +++++++++++++++++++ 8 files changed, 493 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/adc/lpc1850-adc.txt create mode 100644 Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt create mode 100644 drivers/iio/adc/lpc18xx_adc.c create mode 100644 drivers/iio/dac/lpc18xx_dac.c