sunxi: Sync dts files with the upstream kernel

index 9566c81..ec99835 100644
@@ -126,6 +126,7 @@ dtb-$(CONFIG_MACH_SUN4I) += \
 	sun4i-a10-mk802ii.dtb \
 	sun4i-a10-olinuxino-lime.dtb \
 	sun4i-a10-pcduino.dtb \
+	sun4i-a10-pcduino2.dtb \
 	sun4i-a10-pov-protab2-ips9.dtb
 dtb-$(CONFIG_MACH_SUN5I) += \
 	sun5i-a10s-auxtek-t003.dtb \

@@ -156,7 +157,9 @@ dtb-$(CONFIG_MACH_SUN6I) += \
 	sun6i-a31s-colorfly-e708-q1.dtb \
 	sun6i-a31s-cs908.dtb \
 	sun6i-a31s-primo81.dtb \
-	sun6i-a31s-sinovoip-bpi-m2.dtb
+	sun6i-a31s-sina31s.dtb \
+	sun6i-a31s-sinovoip-bpi-m2.dtb \
+	sun6i-a31s-yones-toptech-bs1078-v2.dtb
 dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-ainol-aw1.dtb \
 	sun7i-a20-bananapi.dtb \

@@ -165,6 +168,8 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-cubietruck.dtb \
 	sun7i-a20-hummingbird.dtb \
 	sun7i-a20-i12-tvbox.dtb \
+	sun7i-a20-icnova-swac.dtb \
+	sun7i-a20-itead-ibox.dtb \
 	sun7i-a20-lamobo-r1.dtb \
 	sun7i-a20-m3.dtb \
 	sun7i-a20-m5.dtb \

@@ -191,6 +196,7 @@ dtb-$(CONFIG_MACH_SUN8I_A33) += \
 	sun8i-a33-sinlinx-sina33.dtb
 dtb-$(CONFIG_MACH_SUN8I_A83T) += \
 	sun8i-a83t-allwinner-h8homlet-v2.dtb \
+	sun8i-a83t-cubietruck-plus.dtb \
 	sun8i-a83t-sinovoip-bpi-m3.dtb
 dtb-$(CONFIG_MACH_SUN8I_H3) += \
 	sun8i-h3-orangepi-pc.dtb \

156 lines not on this page · raw message

index 2630d78..97570cb 100644
@@ -93,6 +93,10 @@
 	status = "okay";
 };
 
+&codec {
+	status = "okay";
+};
+
 &ehci0 {
 	status = "okay";
 };

index 1430568..023b03e 100644
@@ -45,6 +45,7 @@
 #include "sunxi-common-regulators.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "Chuwi V7 CW0825";

@@ -78,6 +79,27 @@
 	};
 };
 
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	status = "okay";
+
+	ft5306de4: touchscreen at 38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>;
+		touchscreen-size-x = <1024>;
+		touchscreen-size-y = <768>;
+	};
+};
+
 &lradc {
 	vref-supply = <&reg_vcc3v0>;
 	status = "okay";

index 046a84d..710e2ef 100644
@@ -83,6 +83,10 @@
 	status = "okay";
 };
 
+&codec {
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
 };

107 lines not on this page · raw message

83 lines not on this page · raw message

166 lines not on this page · raw message

205 lines not on this page · raw message

127 lines not on this page · raw message

index dc2f2ae..7afc7a6 100644
@@ -156,6 +156,10 @@
 	status = "okay";
 };
 
+&otg_sram {
+	status = "okay";
+};
+
 &pio {
 	emac_power_pin_q5: emac_power_pin at 0 {
 		allwinner,pins = "PH19";

@@ -172,6 +176,11 @@
 	};
 };
 
+&reg_usb0_vbus {
+	regulator-boot-on;
+	status = "okay";
+};
+
 &reg_usb1_vbus {
 	status = "okay";
 };

@@ -186,7 +195,13 @@
 	status = "okay";
 };
 
+&usb_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
 &usbphy {
+	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	usb2_vbus-supply = <&reg_usb2_vbus>;
 	status = "okay";

index 02158bc..8e50723 100644
@@ -91,6 +91,10 @@
 	status = "okay";
 };
 
+&codec {
+	status = "okay";
+};
+
 &ehci0 {
 	status = "okay";
 };

@@ -154,6 +158,10 @@
 	status = "okay";
 };
 
+&otg_sram {
+	status = "okay";
+};
+
 &pio {
 	led_pins_marsboard: led_pins at 0 {
 		allwinner,pins = "PB5", "PB6", "PB7", "PB8";

@@ -161,6 +169,13 @@
 		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
 		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
+
+	usb0_id_detect_pin: usb0_id_detect_pin at 0 {
+		allwinner,pins = "PH4";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
 };
 
 &reg_usb1_vbus {

@@ -184,7 +199,15 @@
 	status = "okay";
 };
 
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
 &usbphy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_id_detect_pin>;
+	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	usb2_vbus-supply = <&reg_usb2_vbus>;
 	status = "okay";

index 3c7eebe..ee46ea8 100644
@@ -44,6 +44,7 @@
 #include "sun4i-a10.dtsi"
 #include "sunxi-common-regulators.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "MK802";

@@ -58,6 +59,10 @@
 	};
 };
 
+&codec {
+	status = "okay";
+};
+
 &ehci0 {
 	status = "okay";
 };

@@ -80,7 +85,25 @@
 	status = "okay";
 };
 
+&otg_sram {
+	status = "okay";
+};
+
 &pio {
+	usb0_id_detect_pin: usb0_id_detect_pin at 0 {
+		allwinner,pins = "PH4";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	usb0_vbus_detect_pin: usb0_vbus_detect_pin at 0 {
+		allwinner,pins = "PH5";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	usb2_vbus_pin_mk802: usb2_vbus_pin at 0 {
 		allwinner,pins = "PH12";
 		allwinner,function = "gpio_out";

@@ -89,6 +112,10 @@
 	};
 };
 
+&reg_usb0_vbus {
+	status = "okay";
+};
+
 &reg_usb1_vbus {
 	status = "okay";
 };

@@ -105,7 +132,17 @@
 	status = "okay";
 };
 
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
 &usbphy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+	usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+	usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	usb2_vbus-supply = <&reg_usb2_vbus>;
 	status = "okay";

index 28e32ad..b350448 100644
@@ -124,6 +124,18 @@
 	};
 };
 
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+
+	eeprom: eeprom at 50 {
+		compatible = "atmel,24c16";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
 &mdio {
 	status = "okay";
 

94 lines not on this page · raw message

75 lines not on this page · raw message

110 lines not on this page · raw message

234 lines not on this page · raw message

index 2b3511e..a790ec8 100644
@@ -86,6 +86,20 @@
 	status = "okay";
 };
 
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	axp152: pmic at 30 {
+		compatible = "x-powers,axp152";
+		reg = <0x30>;
+		interrupts = <0>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t004>;

index 5a422c1..86d046a 100644
@@ -111,7 +111,7 @@
 	status = "okay";
 
 	at24 at 50 {
-		compatible = "at,24c16";
+		compatible = "atmel,24c16";
 		pagesize = <16>;
 		reg = <0x50>;
 		read-only;

index 7fbb0b0..6efbba6 100644
@@ -123,7 +123,7 @@
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_inet98fv2>;
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_d709>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */

@@ -131,27 +131,12 @@
 	status = "okay";
 };
 
-&mmc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc2_pins_a>;
-	vmmc-supply = <&reg_vcc3v3>;
-	bus-width = <8>;
-	non-removable;
-	status = "okay";
-
-	mmccard: mmccard at 0 {
-		reg = <0>;
-		compatible = "mmc-card";
-		broken-hpi;
-	};
-};
-
 &otg_sram {
 	status = "okay";
 };
 
 &pio {
-	mmc0_cd_pin_inet98fv2: mmc0_cd_pin at 0 {
+	mmc0_cd_pin_d709: mmc0_cd_pin at 0 {
 		allwinner,pins = "PG0";
 		allwinner,function = "gpio_in";
 		allwinner,drive = <SUN4I_PINCTRL_10_MA>;

index 6d466a2..1b11ec9 100644
@@ -123,21 +123,6 @@
 	status = "okay";
 };
 
-&mmc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc2_pins_a>;
-	vmmc-supply = <&reg_vcc3v3>;
-	bus-width = <8>;
-	non-removable;
-	status = "okay";
-
-	mmccard: mmccard at 0 {
-		reg = <0>;
-		compatible = "mmc-card";
-		broken-hpi;
-	};
-};
-
 &otg_sram {
 	status = "okay";
 };

@@ -201,11 +186,6 @@
 	status = "okay";
 };
 
-&reg_usb1_vbus {
-	gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
-	status = "okay";
-};
-
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart1_pins_b>;

@@ -221,16 +201,12 @@
 	allwinner,pins = "PG12";
 };
 
-&usb1_vbus_pin_a {
-	allwinner,pins = "PG11";
-};
-
 &usbphy {
 	pinctrl-names = "default";
 	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
 	usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
 	usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
 	usb0_vbus-supply = <&reg_usb0_vbus>;
-	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb1_vbus-supply = <&reg_ldo3>;
 	status = "okay";
 };

index eb793d5..fa9ddfd 100644
@@ -47,11 +47,21 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "Utoo P66";
 	compatible = "utoo,p66", "allwinner,sun5i-a13";
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		/* Note levels of 10 / 20% result in backlight off */
+		brightness-levels = <0 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <6>;
+		/* TODO: backlight uses axp gpio1 as enable pin */
+	};
+
 	i2c_lcd: i2c at 0 {
 		/* The lcd panel i2c interface is hooked up via gpios */
 		compatible = "i2c-gpio";

@@ -63,6 +73,13 @@
 	};
 };
 
+&codec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&codec_pa_pin>;
+	allwinner,pa-gpios = <&pio 6 3 GPIO_ACTIVE_HIGH>; /* PG3 */
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
 };

@@ -158,6 +175,13 @@
 };
 
 &pio {
+	codec_pa_pin: codec_pa_pin at 0 {
+		allwinner,pins = "PG3";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	mmc0_cd_pin_p66: mmc0_cd_pin at 0 {
 		allwinner,pins = "PG0";
 		allwinner,function = "gpio_in";

@@ -201,6 +225,12 @@
 	};
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins>;
+	status = "okay";
+};
+
 &reg_dcdc2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1000000>;

index 0641d68..a78e189 100644
@@ -41,11 +41,21 @@
  */
 #include "sunxi-q8-common.dtsi"
 
+#include <dt-bindings/pwm/pwm.h>
+
 / {
 	aliases {
 		serial0 = &uart1;
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		/* TODO: backlight uses axp gpio1 as enable pin */
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};

74 lines not on this page · raw message

index 9ffee9b..59a9426 100644
@@ -44,6 +44,7 @@
 
 #include "skeleton.dtsi"
 
+#include <dt-bindings/clock/sun4i-a10-pll2.h>
 #include <dt-bindings/dma/sun4i-a10.h>
 #include <dt-bindings/pinctrl/sun4i-a10.h>
 

@@ -102,6 +103,15 @@
 			clock-output-names = "pll1";
 		};
 
+		pll2: clk at 01c20008 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun5i-a13-pll2-clk";
+			reg = <0x01c20008 0x8>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll2-1x", "pll2-2x",
+					     "pll2-4x", "pll2-8x";
+		};
+
 		pll4: clk at 01c20018 {
 			#clock-cells = <0>;
 			compatible = "allwinner,sun4i-a10-pll1-clk";

@@ -285,6 +295,14 @@
 			clock-output-names = "usb_ohci0", "usb_phy";
 		};
 
+		codec_clk: clk at 01c20140 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-codec-clk";
+			reg = <0x01c20140 0x4>;
+			clocks = <&pll2 SUN4I_A10_PLL2_1X>;
+			clock-output-names = "codec";
+		};
+
 		mbus_clk: clk at 01c2015c {
 			#clock-cells = <0>;
 			compatible = "allwinner,sun5i-a13-mbus-clk";

@@ -571,6 +589,19 @@
 			status = "disabled";
 		};
 
+		codec: codec at 01c22c00 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun4i-a10-codec";
+			reg = <0x01c22c00 0x40>;
+			interrupts = <30>;
+			clocks = <&apb0_gates 0>, <&codec_clk>;
+			clock-names = "apb", "codec";
+			dmas = <&dma SUN4I_DMA_NORMAL 19>,
+			       <&dma SUN4I_DMA_NORMAL 19>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
 		sid: eeprom at 01c23800 {
 			compatible = "allwinner,sun4i-a10-sid";
 			reg = <0x01c23800 0x10>;

index 0d0b6f2..f9cf368 100644
@@ -60,6 +60,16 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	i2c_lcd: i2c at 0 {
+		/* The lcd panel i2c interface is hooked up via gpios */
+		compatible = "i2c-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_lcd_pins>;
+		gpios = <&pio 0 23 GPIO_ACTIVE_HIGH>, /* PA23, sda */
+			<&pio 0 24 GPIO_ACTIVE_HIGH>; /* PA24, scl */
+		i2c-gpio,delay-us = <5>;
+	};
 };
 
 &ehci1 {

@@ -94,6 +104,13 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
+
+	mma8452: mma8452 at 1d {
+		compatible = "fsl,mma8452";
+		reg = <0x1d>;
+		interrupt-parent = <&pio>;
+		interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PA9 */
+	};
 };
 
 &mmc0 {

@@ -124,6 +141,13 @@
 		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
 		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
+
+	i2c_lcd_pins: i2c_lcd_pin at 0 {
+		allwinner,pins = "PA23", "PA24";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
 };
 
 &reg_usb2_vbus {

181 lines not on this page · raw message

131 lines not on this page · raw message

265 lines not on this page · raw message

199 lines not on this page · raw message

166 lines not on this page · raw message

82 lines not on this page · raw message

78 lines not on this page · raw message

index 39a51d5..1fa832d 100644

Lines of this file are not shown. View the raw message.

index e6b0192..8da939a 100644

Lines of this file are not shown. View the raw message.

50 lines not on this page · raw message

91 lines not on this page · raw message

index 975b0b2..5ee43d8 100644

Lines of this file are not shown. View the raw message.

index 4f432f8..90ff4a2 100644

Lines of this file are not shown. View the raw message.

95 lines not on this page · raw message

index 0423708..35ad700 100644

Lines of this file are not shown. View the raw message.

47 lines not on this page · raw message

index c5d70ca..7e3006f 100644

Lines of this file are not shown. View the raw message.

index 73cd81e..2be04c4 100644

Lines of this file are not shown. View the raw message.

index 55a06ce..71125bf 100644

Lines of this file are not shown. View the raw message.

69 lines not on this page · raw message

58 lines not on this page · raw message

90 lines not on this page · raw message

187 lines not on this page · raw message

113 lines not on this page · raw message

71 lines not on this page · raw message

120 lines not on this page · raw message

index 2cc27c7..92e6616 100644

Lines of this file are not shown. View the raw message.

83 lines not on this page · raw message

45 lines not on this page · raw message

48 lines not on this page · raw message

125 lines not on this page · raw message

69 lines not on this page · raw message

63 lines not on this page · raw message

189 lines not on this page · raw message

96 lines not on this page · raw message

index 6484dcf..eb2ccd0 100644

Lines of this file are not shown. View the raw message.

48 lines not on this page · raw message

204 lines not on this page · raw message

55 lines not on this page · raw message

index 17b26ff..b824146 100644

Lines of this file are not shown. View the raw message.

index ec99835..1a0d577 100644
@@ -189,6 +189,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 dtb-$(CONFIG_MACH_SUN8I_A23) += \
 	sun8i-a23-evb.dtb \
 	sun8i-a23-gt90h-v4.dtb \
+	sun8i-a23-polaroid-mid2809pxe04.dtb \
 	sun8i-a23-q8-tablet.dtb
 dtb-$(CONFIG_MACH_SUN8I_A33) += \
 	sun8i-a33-ga10h-v1.1.dtb \

243 lines not on this page · raw message

index 7c1c025..5535326 100644
@@ -55,6 +55,7 @@ F:	configs/ga10h_v1_1_defconfig
 F:	configs/gt90h_v4_defconfig
 F:	configs/orangepi_pc_defconfig
 F:	configs/orangepi_plus_defconfig
+F:	configs/polaroid_mid2809pxe04_defconfig
 F:	configs/q8_a23_tablet_800x480_defconfig
 F:	configs/q8_a33_tablet_800x480_defconfig
 F:	configs/q8_a33_tablet_1024x600_defconfig

new file mode 100644
index 0000000..019f6da
@@ -0,0 +1,25 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN8I_A23=y
+CONFIG_DRAM_CLK=432
+CONFIG_DRAM_ZQ=63351
+CONFIG_MMC0_CD_PIN="PB4"
+CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
+CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_USB0_ID_DET="PH8"
+CONFIG_AXP_GPIO=y
+CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:36,ri:210,up:18,lo:22,hs:10,vs:5,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_DCLK_PHASE=0
+CONFIG_VIDEO_LCD_POWER="PH7"
+CONFIG_VIDEO_LCD_BL_EN="PH6"
+CONFIG_VIDEO_LCD_BL_PWM="PH0"
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-a23-polaroid-mid2809pxe04"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+CONFIG_AXP_DLDO1_VOLT=3300
+CONFIG_USB_MUSB_HOST=y