Skip to contentSkip to conversation

GuC reset-and-retry patches (resend)

PATCH In review Dave Gordon 3 participants 7 messages Apr 4, 2016 – Apr 5, 2016

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

v4 cover GuC reset-and-retry patches (resend)

This is a resend, primarily for CI purposes. All patches to be merged have already been reviewed. The final patch (NOT to be merged) enables GuC loading and submission for testing purposes.

Arun Siluvery (1):
drm/i915/guc: reset GuC and retry on firmware load failure

Dave Gordon (2):
drm/i915/guc: always reset GuC before loading firmware drm/i915: add enable_guc_loading parameter

 drivers/gpu/drm/i915/i915_drv.h         |   1 +
 drivers/gpu/drm/i915/i915_gem.c         |   1 -
 drivers/gpu/drm/i915/i915_guc_reg.h     |  11 ++-
 drivers/gpu/drm/i915/i915_params.c      |  14 ++-
 drivers/gpu/drm/i915/i915_params.h      |   3 +-
 drivers/gpu/drm/i915/i915_reg.h         |   1 +
 drivers/gpu/drm/i915/intel_guc_loader.c | 147 ++++++++++++++++++++++----------
 drivers/gpu/drm/i915/intel_uncore.c     |  19 +++++
 8 files changed, 144 insertions(+), 53 deletions(-)
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#1 lore raw

PATCH v4 1/3 drm/i915/guc: reset GuC and retry on firmware load failure

From: Arun Siluvery <[email protected]>

Due to timing issues in the HW, some of the status bits required for GuC authentication occasionally don't get set; when that happens, the GuC cannot be initialized and we will be left with a wedged GPU. The W/A suggested is to perform a soft reset of the GuC and attempt to reload the F/W again for few times before giving up.

As the failure is dependent on timing, tests performed by triggering manual full gpu reset (i915_wedged) showed that we could sometimes hit this after several thousand iterations, but sometimes tests ran even longer without any issues. Reset and reload mechanism proved helpful when we indeed hit f/w load failure, so it is better to include this to improve driver stability.

This change implements the following WAs,

WaEnableuKernelHeaderValidFix:skl,bxt
WaEnableGuCBootHashCheckNotSet:skl,bxt

---
 drivers/gpu/drm/i915/i915_drv.h         |  1 +
 drivers/gpu/drm/i915/i915_guc_reg.h     |  1 +
 drivers/gpu/drm/i915/i915_reg.h         |  1 +
 drivers/gpu/drm/i915/intel_guc_loader.c | 49 +++++++++++++++++++++++++++++++--
 drivers/gpu/drm/i915/intel_uncore.c     | 19 +++++++++++++
 5 files changed, 69 insertions(+), 2 deletions(-)
drivers/gpu/drm/i915/i915_drv.h +1 -0
index dd18772..1847ef9 100644
@@ -2746,6 +2746,7 @@ extern long i915_compat_ioctl(struct file *filp, unsigned int cmd,
 extern int intel_gpu_reset(struct drm_device *dev, u32 engine_mask);
 extern bool intel_has_gpu_reset(struct drm_device *dev);
 extern int i915_reset(struct drm_device *dev);
+extern int intel_guc_reset(struct drm_i915_private *dev_priv);
 extern void intel_engine_init_hangcheck(struct intel_engine_cs *engine);
 extern unsigned long i915_chipset_val(struct drm_i915_private *dev_priv);
 extern unsigned long i915_mch_val(struct drm_i915_private *dev_priv);
drivers/gpu/drm/i915/i915_guc_reg.h +1 -0
index e4ba582..94ceee5 100644
@@ -27,6 +27,7 @@
 /* Definitions of GuC H/W registers, bits, etc */
 
 #define GUC_STATUS			_MMIO(0xc000)
+#define   GS_MIA_IN_RESET		(1 << 0)
 #define   GS_BOOTROM_SHIFT		1
 #define   GS_BOOTROM_MASK		  (0x7F << GS_BOOTROM_SHIFT)
 #define   GS_BOOTROM_RSA_FAILED		  (0x50 << GS_BOOTROM_SHIFT)
drivers/gpu/drm/i915/i915_reg.h +1 -0
index 12f5103..f4ebf31 100644
@@ -165,6 +165,7 @@ static inline bool i915_mmio_reg_valid(i915_reg_t reg)
 #define  GEN6_GRDOM_MEDIA		(1 << 2)
 #define  GEN6_GRDOM_BLT			(1 << 3)
 #define  GEN6_GRDOM_VECS		(1 << 4)
+#define  GEN9_GRDOM_GUC			(1 << 5)
 #define  GEN8_GRDOM_MEDIA2		(1 << 7)
 
 #define RING_PP_DIR_BASE(ring)		_MMIO((ring)->mmio_base+0x228)
drivers/gpu/drm/i915/intel_guc_loader.c +47 -2

62 lines not on this page · raw message

drivers/gpu/drm/i915/intel_uncore.c +19 -0
index ac1c545..fbc1d21 100644
@@ -1673,6 +1673,25 @@ bool intel_has_gpu_reset(struct drm_device *dev)
 	return intel_get_gpu_reset(dev) != NULL;
 }
 
+int intel_guc_reset(struct drm_i915_private *dev_priv)
+{
+	int ret;
+	unsigned long irqflags;
+
+	if (!i915.enable_guc_submission)
+		return -EINVAL;
+
+	intel_uncore_forcewake_get(dev_priv, FORCEWAKE_ALL);
+	spin_lock_irqsave(&dev_priv->uncore.lock, irqflags);
+
+	ret = gen6_hw_domain_reset(dev_priv, GEN9_GRDOM_GUC);
+
+	spin_unlock_irqrestore(&dev_priv->uncore.lock, irqflags);
+	intel_uncore_forcewake_put(dev_priv, FORCEWAKE_ALL);
+
+	return ret;
+}
+
 bool intel_uncore_unclaimed_mmio(struct drm_i915_private *dev_priv)
 {
 	return check_for_unclaimed_mmio(dev_priv);
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#2 lore raw

PATCH v4 2/3 drm/i915/guc: always reset GuC before loading firmware

In reply to Dave Gordon

After a suspend-resume cycle, the resumed kernel has no idea what the booted kernel may have done to the GuC before replacing itself with the resumed image. In particular, it may have already loaded the GuC with firmware, which will then cause this kernel's attempt to (re)load the firmware to fail (GuC program memory is write-once!). The symptoms (GuC firmware reload fails after hibernation) are further described in the Bugzilla reference below.

So let's *always* reset the GuC just before (re)loading the firmware; the hardware should then be in a well-known state, and we may even avoid some of the issues arising from unpredictable timing.

Also added some more fields & values to the definition of the GUC_STATUS register, which is the key diagnostic indicator if the GuC load fails.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94390

---
 drivers/gpu/drm/i915/i915_guc_reg.h     | 12 ++++++++--
 drivers/gpu/drm/i915/intel_guc_loader.c | 40 ++++++++++++++++-----------------
 2 files changed, 29 insertions(+), 23 deletions(-)
drivers/gpu/drm/i915/i915_guc_reg.h +10 -2
index 94ceee5..80786d9 100644
@@ -27,10 +27,12 @@
 /* Definitions of GuC H/W registers, bits, etc */
 
 #define GUC_STATUS			_MMIO(0xc000)
-#define   GS_MIA_IN_RESET		(1 << 0)
+#define   GS_RESET_SHIFT		0
+#define   GS_MIA_IN_RESET		  (0x01 << GS_RESET_SHIFT)
 #define   GS_BOOTROM_SHIFT		1
 #define   GS_BOOTROM_MASK		  (0x7F << GS_BOOTROM_SHIFT)
 #define   GS_BOOTROM_RSA_FAILED		  (0x50 << GS_BOOTROM_SHIFT)
+#define   GS_BOOTROM_JUMP_PASSED	  (0x76 << GS_BOOTROM_SHIFT)
 #define   GS_UKERNEL_SHIFT		8
 #define   GS_UKERNEL_MASK		  (0xFF << GS_UKERNEL_SHIFT)
 #define   GS_UKERNEL_LAPIC_DONE		  (0x30 << GS_UKERNEL_SHIFT)
@@ -38,7 +40,13 @@
 #define   GS_UKERNEL_READY		  (0xF0 << GS_UKERNEL_SHIFT)
 #define   GS_MIA_SHIFT			16
 #define   GS_MIA_MASK			  (0x07 << GS_MIA_SHIFT)
-#define   GS_MIA_CORE_STATE		  (1 << GS_MIA_SHIFT)
+#define   GS_MIA_CORE_STATE		  (0x01 << GS_MIA_SHIFT)
+#define   GS_MIA_HALT_REQUESTED		  (0x02 << GS_MIA_SHIFT)
+#define   GS_MIA_ISR_ENTRY		  (0x04 << GS_MIA_SHIFT)
+#define   GS_AUTH_STATUS_SHIFT		30
+#define   GS_AUTH_STATUS_MASK		  (0x03 << GS_AUTH_STATUS_SHIFT)
+#define   GS_AUTH_STATUS_BAD		  (0x01 << GS_AUTH_STATUS_SHIFT)
+#define   GS_AUTH_STATUS_GOOD		  (0x02 << GS_AUTH_STATUS_SHIFT)
 
 #define SOFT_SCRATCH(n)			_MMIO(0xc180 + (n) * 4)
 #define SOFT_SCRATCH_COUNT		16
drivers/gpu/drm/i915/intel_guc_loader.c +19 -21
index d84c560..876e5da 100644
@@ -387,7 +387,7 @@ int intel_guc_ucode_load(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
 	struct intel_guc_fw *guc_fw = &dev_priv->guc.guc_fw;
-	int err = 0;
+	int retries, err = 0;
 
 	if (!i915.enable_guc_submission)
 		return 0;
@@ -441,29 +441,26 @@ int intel_guc_ucode_load(struct drm_device *dev)
 	 * steppings also so this is extended as well.
 	 */
 	/* WaEnableGuCBootHashCheckNotSet:skl,bxt */
-	err = guc_ucode_xfer(dev_priv);
-	if (err) {
-		int retries = 3;
-
-		DRM_ERROR("GuC fw load failed, err=%d, attempting reset and retry\n", err);
-
-		while (retries--) {
-			err = i915_reset_guc(dev_priv);
-			if (err)
-				break;
-
-			err = guc_ucode_xfer(dev_priv);
-			if (!err) {
-				DRM_DEBUG_DRIVER("GuC fw reload succeeded after reset\n");
-				break;
-			}
-			DRM_DEBUG_DRIVER("GuC fw reload retries left: %d\n", retries);
-		}
-
+	for (retries = 3; ; ) {
+		/*
+		 * Always reset the GuC just before (re)loading, so
+		 * that the state and timing are fairly predictable
+		 */
+		err = i915_reset_guc(dev_priv);
 		if (err) {
-			DRM_ERROR("GuC fw reload attempt failed, ret=%d\n", err);
+			DRM_ERROR("GuC reset failed, err %d\n", err);
 			goto fail;
 		}
+
+		err = guc_ucode_xfer(dev_priv);
+		if (!err)
+			break;
+
+		if (--retries == 0)
+			goto fail;
+
+		DRM_INFO("GuC fw load failed, err %d; will reset and "
+			"retry %d more time(s)\n", err, retries);
 	}
 
 	guc_fw->guc_fw_load_status = GUC_FIRMWARE_SUCCESS;
@@ -485,6 +482,7 @@ int intel_guc_ucode_load(struct drm_device *dev)
 	return 0;
 
 fail:
+	DRM_ERROR("GuC firmware load failed, err %d\n", err);
 	if (guc_fw->guc_fw_load_status == GUC_FIRMWARE_PENDING)
 		guc_fw->guc_fw_load_status = GUC_FIRMWARE_FAIL;
 
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#3 lore raw

PATCH v4 3/3 DO NOT MERGE: add enable_guc_loading parameter

In reply to Dave Gordon

Split the function of "enable_guc_submission" into two separate options. The new one "enable_guc_loading" controls only the *fetching and loading* of the GuC firmware image. The existing one is redefined to control only the *use* of the GuC for batch submission once the firmware is loaded.

In addition, the degree of control has been refined from a simple bool to an integer key, allowing several options:

 -1  (default)    whatever the platform default is
  0  DISABLE      don't load/use the GuC
  1  BEST EFFORT  try to load/use the GuC, fallback if not available
  2  REQUIRE      must load/use the GuC, else leave the GPU wedged

The new platform default (as coded here) will be to attempt to load the GuC iff the device has a GuC that requires firmware, to attempt to use it iff the device has a GuC that supports the submission protocol (with or without firmware), and to fall back to execlist mode if any required firmware cannot be found or fails to load.

---
 drivers/gpu/drm/i915/i915_gem.c         |  1 -
 drivers/gpu/drm/i915/i915_params.c      | 14 ++++-
 drivers/gpu/drm/i915/i915_params.h      |  3 +-
 drivers/gpu/drm/i915/intel_guc_loader.c | 98 ++++++++++++++++++---------------
 4 files changed, 67 insertions(+), 49 deletions(-)
drivers/gpu/drm/i915/i915_gem.c +0 -1
index ca96fc1..da34db5 100644
@@ -4885,7 +4885,6 @@ int i915_gem_init_engines(struct drm_device *dev)
 		ret = intel_guc_ucode_load(dev);
 		if (ret) {
 			DRM_ERROR("Failed to initialize GuC, error %d\n", ret);
-			ret = -EIO;
 			goto out;
 		}
 	}
drivers/gpu/drm/i915/i915_params.c +11 -3
index 1779f02..21f325b 100644
@@ -54,7 +54,8 @@ struct i915_params i915 __read_mostly = {
 	.verbose_state_checks = 1,
 	.nuclear_pageflip = 0,
 	.edp_vswing = 0,
-	.enable_guc_submission = false,
+	.enable_guc_loading = -1,
+	.enable_guc_submission = -1,
 	.guc_log_level = -1,
 	.enable_dp_mst = true,
 	.inject_load_failure = 0,
@@ -197,8 +198,15 @@ struct i915_params i915 __read_mostly = {
 		 "(0=use value from vbt [default], 1=low power swing(200mV),"
 		 "2=default swing(400mV))");
 
-module_param_named_unsafe(enable_guc_submission, i915.enable_guc_submission, bool, 0400);
-MODULE_PARM_DESC(enable_guc_submission, "Enable GuC submission (default:false)");
+module_param_named_unsafe(enable_guc_loading, i915.enable_guc_loading, int, 0400);
+MODULE_PARM_DESC(enable_guc_submission,
+		"Enable GuC firmware loading "
+		"(-1=auto [default], 0=never, 1=if available, 2=required)");
+
+module_param_named_unsafe(enable_guc_submission, i915.enable_guc_submission, int, 0400);
+MODULE_PARM_DESC(enable_guc_submission,
+		"Enable GuC submission "
+		"(-1=auto [default], 0=never, 1=if available, 2=required)");
 
 module_param_named(guc_log_level, i915.guc_log_level, int, 0400);
 MODULE_PARM_DESC(guc_log_level,
drivers/gpu/drm/i915/i915_params.h +2 -1
index 02bc278..9f1d17b 100644
@@ -45,6 +45,8 @@ struct i915_params {
 	int enable_ips;
 	int invert_brightness;
 	int enable_cmd_parser;
+	int enable_guc_loading;
+	int enable_guc_submission;
 	int guc_log_level;
 	int use_mmio_flip;
 	int mmio_debug;
@@ -57,7 +59,6 @@ struct i915_params {
 	bool load_detect_test;
 	bool reset;
 	bool disable_display;
-	bool enable_guc_submission;
 	bool verbose_state_checks;
 	bool nuclear_pageflip;
 	bool enable_dp_mst;
drivers/gpu/drm/i915/intel_guc_loader.c +54 -44

149 lines not on this page · raw message

Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#4 lore raw

✗ Fi.CI.BAT: failure for GuC reset-and-retry patches (resend)

In reply to Dave Gordon
== Series Details ==

== Series Details ==

Series: GuC reset-and-retry patches (resend)
URL : https://patchwork.freedesktop.org/series/5287/
State : failure

== Summary ==

Series 5287v1 GuC reset-and-retry patches (resend)
http://patchwork.freedesktop.org/api/1.0/series/5287/revisions/1/mbox/

Test gem_ctx_switch:

        Subgroup basic-default:
                pass       -> DMESG-WARN (skl-i7k-2)
Test gem_sync:
        Subgroup basic-bsd:
                pass       -> DMESG-FAIL (ilk-hp8440p)
Test kms_flip:
        Subgroup basic-flip-vs-dpms:
                pass       -> DMESG-WARN (ilk-hp8440p) UNSTABLE
Test kms_force_connector_basic:
        Subgroup prune-stale-modes:
                skip       -> PASS       (ilk-hp8440p)
Test kms_pipe_crc_basic:
        Subgroup suspend-read-crc-pipe-b:
                incomplete -> PASS       (hsw-gt2)
Test pm_rpm:
        Subgroup basic-pci-d3-state:
                pass       -> DMESG-WARN (bsw-nuc-2)
bdw-nuci7        total:196  pass:184  dwarn:0   dfail:0   fail:0   skip:12 
bdw-ultra        total:196  pass:175  dwarn:0   dfail:0   fail:0   skip:21 
bsw-nuc-2        total:196  pass:158  dwarn:1   dfail:0   fail:0   skip:37 
byt-nuc          total:196  pass:161  dwarn:0   dfail:0   fail:0   skip:35 
hsw-brixbox      total:196  pass:174  dwarn:0   dfail:0   fail:0   skip:22 
hsw-gt2          total:196  pass:179  dwarn:0   dfail:0   fail:0   skip:17 
ilk-hp8440p      total:196  pass:130  dwarn:1   dfail:1   fail:0   skip:64 
ivb-t430s        total:196  pass:171  dwarn:0   dfail:0   fail:0   skip:25 
skl-i7k-2        total:196  pass:172  dwarn:1   dfail:0   fail:0   skip:23 
snb-dellxps      total:196  pass:162  dwarn:0   dfail:0   fail:0   skip:34 
snb-x220t        total:196  pass:162  dwarn:0   dfail:0   fail:1   skip:33 

Results at /archive/results/CI_IGT_test/Patchwork_1794/

aedfaaef290af9c8df7d9f4adf22cbe21704d091 drm-intel-nightly: 2016y-04m-04d-13h-09m-54s UTC integration manifest c7e3e58bc5509154a98e7c2fa1e433538f67c97a DO NOT MERGE: add enable_guc_loading parameter 87ce739817a1d65a3770c67d27560ea7377ad05e drm/i915/guc: always reset GuC before loading firmware 4f0836e699a720d8429de99f8d374e3a732a16f5 drm/i915/guc: reset GuC and retry on firmware load failure

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#5 lore raw

Re: ✗ Fi.CI.BAT: failure for GuC reset-and-retry patches (resend)

Quoted 6 lines · Patchwork

== Series Details ==

Series: GuC reset-and-retry patches (resend)
URL : https://patchwork.freedesktop.org/series/5287/
State : failure

Quoted 8 lines

== Summary ==

Series 5287v1 GuC reset-and-retry patches (resend)
http://patchwork.freedesktop.org/api/1.0/series/5287/revisions/1/mbox/

Test gem_ctx_switch:

         Subgroup basic-default:
                 pass       -> DMESG-WARN (skl-i7k-2)

https://bugs.freedesktop.org/show_bug.cgi?id=93847
GuC is calling a sleeping function in atomic context Fix in progress (unrelated to the reset-and-retry patches)

Quoted 3 lines

Test gem_sync:

         Subgroup basic-bsd:
                 pass       -> DMESG-FAIL (ilk-hp8440p)

https://bugs.freedesktop.org/show_bug.cgi?id=94307
[BAT ILK] gem_sync/basic-bsd fails / hangcheck timer elapsed Unrelated; being investigated by Gabriel Feceoru

Quoted 3 lines

Test kms_flip:

         Subgroup basic-flip-vs-dpms:
                 pass       -> DMESG-WARN (ilk-hp8440p) UNSTABLE

https://bugs.freedesktop.org/show_bug.cgi?id=93787
[BAT ILK] sporadic fifo underruns in igt@kms_flip@basic-flip-vs-* on ilk-hp8440p (edit) Unrelated

Quoted 9 lines

Test kms_force_connector_basic:

         Subgroup prune-stale-modes:
                 skip       -> PASS       (ilk-hp8440p)
Test kms_pipe_crc_basic:
         Subgroup suspend-read-crc-pipe-b:
                 incomplete -> PASS       (hsw-gt2)
Test pm_rpm:
         Subgroup basic-pci-d3-state:
                 pass       -> DMESG-WARN (bsw-nuc-2)

https://bugs.freedesktop.org/show_bug.cgi?id=94164
[BAT BYT/BSW] Runtime PM: *ERROR* Unclaimed access detected prior to suspending Unrelated

Quoted 12 lines
bdw-nuci7        total:196  pass:184  dwarn:0   dfail:0   fail:0   skip:12
bdw-ultra        total:196  pass:175  dwarn:0   dfail:0   fail:0   skip:21
bsw-nuc-2        total:196  pass:158  dwarn:1   dfail:0   fail:0   skip:37
byt-nuc          total:196  pass:161  dwarn:0   dfail:0   fail:0   skip:35
hsw-brixbox      total:196  pass:174  dwarn:0   dfail:0   fail:0   skip:22
hsw-gt2          total:196  pass:179  dwarn:0   dfail:0   fail:0   skip:17
ilk-hp8440p      total:196  pass:130  dwarn:1   dfail:1   fail:0   skip:64
ivb-t430s        total:196  pass:171  dwarn:0   dfail:0   fail:0   skip:25
skl-i7k-2        total:196  pass:172  dwarn:1   dfail:0   fail:0   skip:23
snb-dellxps      total:196  pass:162  dwarn:0   dfail:0   fail:0   skip:34
snb-x220t        total:196  pass:162  dwarn:0   dfail:0   fail:1   skip:33
Quoted 6 lines

Results at /archive/results/CI_IGT_test/Patchwork_1794/

aedfaaef290af9c8df7d9f4adf22cbe21704d091 drm-intel-nightly: 2016y-04m-04d-13h-09m-54s UTC integration manifest c7e3e58bc5509154a98e7c2fa1e433538f67c97a DO NOT MERGE: add enable_guc_loading parameter 87ce739817a1d65a3770c67d27560ea7377ad05e drm/i915/guc: always reset GuC before loading firmware 4f0836e699a720d8429de99f8d374e3a732a16f5 drm/i915/guc: reset GuC and retry on firmware load failure

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#6 lore raw

Re: ✗ Fi.CI.BAT: failure for GuC reset-and-retry patches (resend)

Quoted 47 lines · Dave Gordon
Quoted 6 lines · Patchwork

== Series Details ==

Series: GuC reset-and-retry patches (resend)
URL : https://patchwork.freedesktop.org/series/5287/
State : failure

Quoted 8 lines

== Summary ==

Series 5287v1 GuC reset-and-retry patches (resend)
http://patchwork.freedesktop.org/api/1.0/series/5287/revisions/1/mbox/

Test gem_ctx_switch:

         Subgroup basic-default:
                 pass       -> DMESG-WARN (skl-i7k-2)

https://bugs.freedesktop.org/show_bug.cgi?id=93847
GuC is calling a sleeping function in atomic context Fix in progress (unrelated to the reset-and-retry patches)

Quoted 3 lines

Test gem_sync:

         Subgroup basic-bsd:
                 pass       -> DMESG-FAIL (ilk-hp8440p)

https://bugs.freedesktop.org/show_bug.cgi?id=94307
[BAT ILK] gem_sync/basic-bsd fails / hangcheck timer elapsed Unrelated; being investigated by Gabriel Feceoru

Quoted 3 lines

Test kms_flip:

         Subgroup basic-flip-vs-dpms:
                 pass       -> DMESG-WARN (ilk-hp8440p) UNSTABLE

https://bugs.freedesktop.org/show_bug.cgi?id=93787
[BAT ILK] sporadic fifo underruns in igt@kms_flip@basic-flip-vs-* on ilk-hp8440p (edit)
Unrelated

Quoted 9 lines

Test kms_force_connector_basic:

         Subgroup prune-stale-modes:
                 skip       -> PASS       (ilk-hp8440p)
Test kms_pipe_crc_basic:
         Subgroup suspend-read-crc-pipe-b:
                 incomplete -> PASS       (hsw-gt2)
Test pm_rpm:
         Subgroup basic-pci-d3-state:
                 pass       -> DMESG-WARN (bsw-nuc-2)
Quoted 38 lines

https://bugs.freedesktop.org/show_bug.cgi?id=94164
[BAT BYT/BSW] Runtime PM: *ERROR* Unclaimed access detected prior to suspending
Unrelated

Quoted 33 lines

bdw-nuci7 total:196 pass:184 dwarn:0 dfail:0 fail:0
skip:12
bdw-ultra total:196 pass:175 dwarn:0 dfail:0 fail:0
skip:21
bsw-nuc-2 total:196 pass:158 dwarn:1 dfail:0 fail:0
skip:37
byt-nuc total:196 pass:161 dwarn:0 dfail:0 fail:0
skip:35
hsw-brixbox total:196 pass:174 dwarn:0 dfail:0 fail:0
skip:22
hsw-gt2 total:196 pass:179 dwarn:0 dfail:0 fail:0
skip:17
ilk-hp8440p total:196 pass:130 dwarn:1 dfail:1 fail:0
skip:64
ivb-t430s total:196 pass:171 dwarn:0 dfail:0 fail:0
skip:25
skl-i7k-2 total:196 pass:172 dwarn:1 dfail:0 fail:0
skip:23
snb-dellxps total:196 pass:162 dwarn:0 dfail:0 fail:0
skip:34
snb-x220t total:196 pass:162 dwarn:0 dfail:0 fail:1
skip:33

Results at /archive/results/CI_IGT_test/Patchwork_1794/

aedfaaef290af9c8df7d9f4adf22cbe21704d091 drm-intel-nightly:
2016y-04m-04d-13h-09m-54s UTC integration manifest c7e3e58bc5509154a98e7c2fa1e433538f67c97a DO NOT MERGE: add enable_guc_loading parameter 87ce739817a1d65a3770c67d27560ea7377ad05e drm/i915/guc: always reset GuC before loading firmware 4f0836e699a720d8429de99f8d374e3a732a16f5 drm/i915/guc: reset GuC and retry on firmware load failure

1 and 2 merged, thanks for the patches and review!

Regards,

Tvrtko

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx