Skip to contentSkip to conversation

UBOOT port to i.MX27ADS - Network and NAND issues

U-Boot Tiju 2 participants 2 messages Sep 15, 2008

lore
Share & tools
lore

Tiju

author
#0 lore raw

Hi All,

I downloaded u-boot-v2 files and compiled it.

There seems to be some issues with the ethernet. When I do a ping, it shows me:

U-Boot 2.0.0-rc5-git (Sep 15 2008 - 12:18:48)

Board: Freescale i.MX27 ADS
cfi_probe: cfi_flash base: 0xc0000000 size: 0x02000000
chip id: [1,882,1,01d]
mpll:     265999329 Hz
spll:     239999725 Hz
arm:      177332886 Hz
perclk1:    8866644 Hz
perclk2:   17733288 Hz
perclk3:   44333221 Hz
perclk4:   17733288 Hz
clkin26:   26000000 Hz
ahb:       44333221 Hz
ipg:       22166610 Hz
Malloc space: 0xa7b00000 -> 0xa7f00000 (size  4 MB)
Stack space : 0xa7af8000 -> 0xa7b00000 (size 32 kB)

running /env/bin/init...
set parameter: Invalid argument
Hit any key to stop autoboot: 3 2 1
set parameter: Invalid argument
phy0: Link is up - 10/Half
*** ERROR: `eth0.ethaddr' not set
phy0: Link is up - 10/Half
*** ERROR: `eth0.ethaddr' not set
Bad Magic Number

uboot:/ ping 199.63.38.1
phy0: Link is up - 10/Half
*** ERROR: `eth0.ethaddr' not set
ping failed; host 199.63.38.1 is not alive

The environment variables are as follows:
uboot:/ printenv
locals:
kernel=net
root=net
ip=dhcp
uimage=uImage-mx27ads
jffs2=root-mx27ads.jffs2
autoboot_timeout=3
nfsroot=/tmp/imx27ads
bootargs=console=ttymxc0,115200 mtdparts=128k(uboot)ro,128k(ubootenv),1536k(kernel),-(root) rootpart=/dev/mtdblock3
globals:
PATH=/env/bin
1. How could I set the eth0.ethaddr or is it that I am missing something here?
2. Is it possible to do a NAND boot on i.mx27ads board with uboot? If so how can I do it?

Thanks in advance.

Tiju

Unlimited freedom, unlimited storage. Get it now, on http://help.yahoo.com/l/in/yahoo/mail/yahoomail/tools/tools-08.html/

#1 lore raw

Hi,

Quoted 38 lines · Tiju

Hi All,

I downloaded u-boot-v2 files and compiled it.

There seems to be some issues with the ethernet. When I do a ping, it shows me:

U-Boot 2.0.0-rc5-git (Sep 15 2008 - 12:18:48)

Board: Freescale i.MX27 ADS
cfi_probe: cfi_flash base: 0xc0000000 size: 0x02000000
chip id: [1,882,1,01d]
mpll:     265999329 Hz
spll:     239999725 Hz
arm:      177332886 Hz
perclk1:    8866644 Hz
perclk2:   17733288 Hz
perclk3:   44333221 Hz
perclk4:   17733288 Hz
clkin26:   26000000 Hz
ahb:       44333221 Hz
ipg:       22166610 Hz
Malloc space: 0xa7b00000 -> 0xa7f00000 (size  4 MB)
Stack space : 0xa7af8000 -> 0xa7b00000 (size 32 kB)

running /env/bin/init...
set parameter: Invalid argument
Hit any key to stop autoboot: 3 2 1
set parameter: Invalid argument
phy0: Link is up - 10/Half
*** ERROR: `eth0.ethaddr' not set
phy0: Link is up - 10/Half
*** ERROR: `eth0.ethaddr' not set
Bad Magic Number

uboot:/ ping 199.63.38.1
phy0: Link is up - 10/Half
*** ERROR: `eth0.ethaddr' not set
ping failed; host 199.63.38.1 is not alive

Quoted 16 lines

The environment variables are as follows:
uboot:/ printenv
locals:
kernel=net
root=net
ip=dhcp
uimage=uImage-mx27ads
jffs2=root-mx27ads.jffs2
autoboot_timeout=3
nfsroot=/tmp/imx27ads
bootargs=console=ttymxc0,115200 mtdparts=128k(uboot)ro,128k(ubootenv),1536k(kernel),-(root) rootpart=/dev/mtdblock3
globals:
PATH=/env/bin
1. How could I set the eth0.ethaddr or is it that I am missing something here?

eth0.ethaddr=80:81:...

I removed the MAC addresses from the default environments since it was a very bad idea.

Quoted 1 line

2. Is it possible to do a NAND boot on i.mx27ads board with uboot? If so how can I do it?

NAND support (including booting from NAND) has been tested on the phycore i.MX27 module. So the NAND driver inself is in place, only the board specific bits are missing. You can use board/pcm038 as a template.

Regards,
Sascha

Signature · 4 lines
 Pengutronix - Linux Solutions for Science and Industry
   Handelsregister:  Amtsgericht Hildesheim, HRA 2686
     Hannoversche Str. 2, 31134 Hildesheim, Germany
   Phone: +49-5121-206917-0 |  Fax: +49-5121-206917-9