Add driver for ST stts751 thermal sensor
Subsystems (2)
v2 cover Add driver for ST stts751 thermal sensor
This series adds new driver for ST stts751 thermal sensor
Changes since v1:
- removed the "manual mode" logic; always use automatic mode
- changed the way 16-bit data is read from two 8-bit regs (now similar to lm90)
- code simplifications
- comment style fixes
Andrea Merello (2):
DT: add binding documentation for STTS751
hwmon: new driver for ST stts751 thermal sensor
.../devicetree/bindings/hwmon/stts751.txt | 19 + drivers/hwmon/Kconfig | 12 +- drivers/hwmon/Makefile | 2 +- drivers/hwmon/stts751.c | 805 +++++++++++++++++++++ 4 files changed, 836 insertions(+), 2 deletions(-) create mode 100644 Documentation/devicetree/bindings/hwmon/stts751.txt create mode 100644 drivers/hwmon/stts751.c
--
2.7.4
PATCH v2 1/2 DT: add binding documentation for STTS751
--- Documentation/devicetree/bindings/hwmon/stts751.txt | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) create mode 100644 Documentation/devicetree/bindings/hwmon/stts751.txt
Documentation/devicetree/bindings/hwmon/stts751.txt new file +19 -0
@@ -0,0 +1,19 @@ +* STTS751 thermometer. + +Required node properties: +- compatible: "stts751" +- reg: I2C bus address of the device + +Optional properties: +- has-therm: specifies that the "therm" pin is wired +- has-event: specifies that the "event" pin is wired +- smbus-timeout-disable: when set, the smbus timeout function will be disabled + +Example stts751 node: + +temp-sensor { + compatible = "stts751"; + reg = <0x48>; + has-therm; + has-event; +}
Signature · 1 line
2.7.4
Guenter Roeck
maintainerRe: [PATCH v2 1/2] DT: add binding documentation for STTS751
Quoted 14 lines · Andrea Merello
Signed-off-by Andrea Merello <[email protected]>Cc Rob Herring <[email protected]>Cc Mark Rutland <[email protected]>--- Documentation/devicetree/bindings/hwmon/stts751.txt | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) create mode 100644 Documentation/devicetree/bindings/hwmon/stts751.txtDocumentation/devicetree/bindings/hwmon/stts751.txt new file +0
-0
Documentation/devicetree/bindings/hwmon/stts751.txt line 9
Quoted 9 lines
Documentation/devicetree/bindings/hwmon/stts751.txt new file +9
-0@@ -0,0 +1,19 @@ +* STTS751 thermometer. + +Required node properties: +- compatible: "stts751" +- reg: I2C bus address of the device + +Optional properties: +- has-therm: specifies that the "therm" pin is wired +- has-event: specifies that the "event" pin is wired
As mentioned in the code patch, I don't think those properties are actually needed.
Guenter
Quoted 17 lines
Documentation/devicetree/bindings/hwmon/stts751.txt new file +10
-0+- smbus-timeout-disable: when set, the smbus timeout function will be disabled + +Example stts751 node: + +temp-sensor { + compatible = "stts751"; + reg = <0x48>; + has-therm; + has-event; +}Signature · 6 lines
2.7.4 -- To unsubscribe from this list: send the line "unsubscribe linux-hwmon" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
PATCH v2 2/2 hwmon: new driver for ST stts751 thermal sensor
In reply to Andrea MerelloThis patch adds a HWMON driver for ST Microelectronics STTS751 temperature sensors.
It does support temperature reading (of course), SMBUS alert functionality and "therm" output.
Thanks-to: LABBE Corentin [for suggestions]
Thanks-to: Guenter Roeck [for suggestions/discussions]
--- drivers/hwmon/Kconfig | 12 +- drivers/hwmon/Makefile | 2 +- drivers/hwmon/stts751.c | 805 ++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 817 insertions(+), 2 deletions(-) create mode 100644 drivers/hwmon/stts751.c
drivers/hwmon/Kconfig +11 -1
@@ -1448,6 +1448,16 @@ config SENSORS_SCH5636 This driver can also be built as a module. If so, the module will be called sch5636. +config SENSORS_STTS751 + tristate "ST Microelectronics STTS751" + depends on I2C + help + If you say yes here you get support for STTS751 + temperature sensor chips. + + This driver can also be built as a module. If so, the module + will be called stts751. + config SENSORS_SMM665 tristate "Summit Microelectronics SMM665" depends on I2C
@@ -1506,7 +1516,7 @@ config SENSORS_ADS7871 config SENSORS_AMC6821 tristate "Texas Instruments AMC6821" - depends on I2C + depends on I2C help If you say yes here you get support for the Texas Instruments AMC6821 hardware monitoring chips.
drivers/hwmon/Makefile +1 -1
@@ -147,6 +147,7 @@ obj-$(CONFIG_SENSORS_SMM665) += smm665.o obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc47b397.o obj-$(CONFIG_SENSORS_SMSC47M1) += smsc47m1.o obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o +obj-$(CONFIG_SENSORS_STTS751) += stts751.o obj-$(CONFIG_SENSORS_AMC6821) += amc6821.o obj-$(CONFIG_SENSORS_TC74) += tc74.o obj-$(CONFIG_SENSORS_THMC50) += thmc50.o
@@ -169,4 +170,3 @@ obj-$(CONFIG_SENSORS_WM8350) += wm8350-hwmon.o obj-$(CONFIG_PMBUS) += pmbus/ ccflags-$(CONFIG_HWMON_DEBUG_CHIP) := -DDEBUG -
drivers/hwmon/stts751.c new file +805 -0
805 lines not on this page · raw message
Signature · 1 line
2.7.4