m68k: add Sysam AMCORE open board support
Subsystems (2)
PATCH RESEND 1/1 m68k: add Sysam AMCORE open board support
Add support for Sysam AMCORE board, an open hardware embedded Linux board, see http://sysam.it/openzone/projects/amcore/amcore.html for any info.
--- arch/m68k/Kconfig.machine | 6 ++ arch/m68k/coldfire/Makefile | 1 + arch/m68k/coldfire/amcore.c | 191 +++++++++++++++++++++++++++++++++++++ arch/m68k/configs/amcore_defconfig | 114 ++++++++++++++++++++++ arch/m68k/include/asm/m5307sim.h | 7 ++ 5 files changed, 319 insertions(+) create mode 100644 arch/m68k/coldfire/amcore.c create mode 100644 arch/m68k/configs/amcore_defconfig
arch/m68k/Kconfig.machine +6 -0
@@ -259,6 +259,12 @@ config M5407C3 help Support for the Motorola M5407C3 board. +config AMCORE + bool "Sysam AMCORE board support" + depends on M5307 + help + Support for the Sysam AMCORE open-hardware generic board. + config FIREBEE bool "FireBee board support" depends on M547x
arch/m68k/coldfire/Makefile +1 -0
@@ -34,6 +34,7 @@ obj-$(CONFIG_NETtel) += nettel.o obj-$(CONFIG_CLEOPATRA) += nettel.o obj-$(CONFIG_FIREBEE) += firebee.o obj-$(CONFIG_MCF8390) += mcf8390.o +obj-$(CONFIG_AMCORE) += amcore.o obj-$(CONFIG_PCI) += pci.o
arch/m68k/coldfire/amcore.c new file +191 -0
191 lines not on this page · raw message
arch/m68k/configs/amcore_defconfig new file +114 -0
114 lines not on this page · raw message
arch/m68k/include/asm/m5307sim.h +7 -0
@@ -131,6 +131,11 @@#define MCFGPIO_IRQ_MAX -1#define MCFGPIO_IRQ_VECBASE -1 +/* +* I2C module. +*/ +#define MCFI2C_IOBASE (MCF_MBAR + 0x280) +/* Definition offset address for CS2-7 -- old mask 5307 */
@@ -148,6 +153,7 @@#define MCFSIM_SWDICR MCFSIM_ICR0/* Watchdog timer ICR */ #define MCFSIM_TIMER1ICR MCFSIM_ICR1/* Timer 1 ICR */ #define MCFSIM_TIMER2ICR MCFSIM_ICR2/* Timer 2 ICR */ +#define MCFSIM_I2CICR MCFSIM_ICR3/* I2C ICR */ #define MCFSIM_UART1ICR MCFSIM_ICR4/* UART 1 ICR */ #define MCFSIM_UART2ICR MCFSIM_ICR5/* UART 2 ICR */ #define MCFSIM_DMA0ICR MCFSIM_ICR6/* DMA 0 ICR */
@@ -174,6 +180,7 @@/* * Define system peripheral IRQ usage. */ +#define MCF_IRQ_I2C 29/* I2C */ #define MCF_IRQ_TIMER 30/* Timer0, Level 6 */ #define MCF_IRQ_PROFILER 31/* Timer1, Level 7 */ #define MCF_IRQ_UART0 73/* UART0 */
Signature · 1 line
2.8.1
Greg Ungerer
maintainerHi Angelo,
Quoted 3 lines · Angelo Dureghello
Add support for Sysam AMCORE board, an open hardware embedded Linux board, see http://sysam.it/openzone/projects/amcore/amcore.html for any info.
Some comments below inline. My comments assume this patch was generated against a current or recent Linux head kernel. But I am not sure if that is the case?
What bus driver does this use for i2c?
Steven King had a patch set a couple of years back that did full ColdFire i2c support - but the sticking point was the i2c bus driver was not acceptable to the i2c driver folks.
But, the ColdFire platform part was good, and I have had a patch that contains just those parts sitting in my m68knommu git tree awaiting testing and some motivation to push it up-stream.
https://git.kernel.org/cgit/linux/kernel/git/gerg/m68knommu.git/commit/?h=i2c
Of course it is not terribly useful without i2c driver support. The mcfi2c include in this patch may need to be removed for one thing.
Quoted 54 lines
Signed-off-by Angelo Dureghello <[email protected]>--- arch/m68k/Kconfig.machine | 6 ++ arch/m68k/coldfire/Makefile | 1 + arch/m68k/coldfire/amcore.c | 191 +++++++++++++++++++++++++++++++++++++ arch/m68k/configs/amcore_defconfig | 114 ++++++++++++++++++++++ arch/m68k/include/asm/m5307sim.h | 7 ++ 5 files changed, 319 insertions(+) create mode 100644 arch/m68k/coldfire/amcore.c create mode 100644 arch/m68k/configs/amcore_defconfigarch/m68k/Kconfig.machine +6
-0@@ -259,6 +259,12 @@ config M5407C3 help Support for the Motorola M5407C3 board. +config AMCORE + bool "Sysam AMCORE board support" + depends on M5307 + help + Support for the Sysam AMCORE open-hardware generic board. + config FIREBEE bool "FireBee board support" depends on M547xarch/m68k/coldfire/Makefile +1
-0@@ -34,6 +34,7 @@ obj-$(CONFIG_NETtel) += nettel.o obj-$(CONFIG_CLEOPATRA) += nettel.o obj-$(CONFIG_FIREBEE) += firebee.o obj-$(CONFIG_MCF8390) += mcf8390.o +obj-$(CONFIG_AMCORE) += amcore.o obj-$(CONFIG_PCI) += pci.oarch/m68k/coldfire/amcore.c new file +8
-0@@ -0,0 +1,191 @@ +/* +* amcore.c -- Support for Sysam AMCORE open board +* +* (C) Copyright 2016, Angelo Dureghello <[email protected]> +* +* This file is subject to the terms and conditions of the GNU General Public +* License. See the file COPYING in the main directory of this archive +* for more details.
arch/m68k/coldfire/amcore.c line 18
Quoted 10 lines
arch/m68k/coldfire/amcore.c new file +10
-0+*/ + +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/dm9000.h> + +#include <linux/irq.h> +#include <linux/interrupt.h> + +#ifdef CONFIG_COLDFIRE
This file can only be compiled for a ColdFire (in fact only 5307 based on your Kconfig.machine and Makefile changes). No need to wrap it in an "#ifdef".
arch/m68k/coldfire/amcore.c line 29
Quoted 11 lines
arch/m68k/coldfire/amcore.c new file +11
-0+#include <asm/coldfire.h> +#include <asm/mcfsim.h> +#endif + +#include <asm/io.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/map.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> +#include <linux/i2c.h> +#include <asm/m5307sim.h>
No need to include m5307sim.h, it is included from mcfsim.h.
Normal practice is to list all the linux/*.h includes first, then the asm/*.h includes.
arch/m68k/coldfire/amcore.c line 34
Quoted 4 lines
arch/m68k/coldfire/amcore.c new file +4
-0+/* +* Name the Board for the /proc/cpuinfo +*/ +const char cf_board_name[] ="Sysam AMCORE" ;
This doesn't appear to be used?
arch/m68k/coldfire/amcore.c line 35
Quoted 2 lines
arch/m68k/coldfire/amcore.c new file +2
-0+ +#if defined(CONFIG_DM9000 ) || defined(CONFIG_DM9000_MODULE )
#if IS_ENABLED(CONFIG_DM9000)
Quoted 105 lines
arch/m68k/coldfire/amcore.c new file +105
-0+#define DM9000_IRQ 25 +#define DM9000_ADDR 0x30000000 + +/* +* DEVICES and related device RESOURCES +*/ +static struct resource dm9000_resources[] = { +/* physical address of the address register (CMD [A2] to 0)*/ + [0 ] = { + .start =DM9000_ADDR , + .end =DM9000_ADDR +3 , + .flags =IORESOURCE_MEM , + }, +/* physical address of the data register (CMD [A2] to 1)*/ + [1 ] = { + .start =DM9000_ADDR +4 , + .end =DM9000_ADDR +4 +0xff , + .flags =IORESOURCE_MEM , + }, +/* IRQ line the device's interrupt pin is connected to */ + [2 ] = { + .start =DM9000_IRQ , + .end =DM9000_IRQ , + .flags =IORESOURCE_IRQ , + }, +}; + +static struct dm9000_plat_data dm9000_platdata = { + .flags =DM9000_PLATF_32BITONLY , +}; + +static struct platform_device dm9000_device = { + .name ="dm9000" , + .id =0 , + .num_resources =ARRAY_SIZE (dm9000_resources), + .resource = dm9000_resources, + .dev = { + .platform_data = &dm9000_platdata, + } +}; +#endif + +static void __init dm9000_pre_init (void ) +{ +/* Set the dm9000 interrupt to be auto-vectored */ +mcf_autovector (DM9000_IRQ ); +} + +/* +* Partitioning of parallel NOR flash (39VF3201B) +*/ +static struct mtd_partition amcore_partitions[] = { +{ + .name ="U-Boot (128K)" , + .size =0x20000 , + .offset =0x0 +}, +{ + .name ="Kernel+ROMfs (2994K)" , + .size =0x2E0000 , + .offset =MTDPART_OFS_APPEND +}, +{ + .name ="Flash Free Space (1024K)" , + .size =MTDPART_SIZ_FULL , + .offset =MTDPART_OFS_APPEND +} +}; + +static struct physmap_flash_data flash_data = { + .parts = amcore_partitions, + .nr_parts =ARRAY_SIZE (amcore_partitions), + .width =2 , +}; + +static struct resource flash_resource = { + .start =0xffc00000 , + .end =0xffffffff , + .flags =IORESOURCE_MEM , +}; + +static struct platform_device flash_device = { + .name ="physmap-flash" , + .id =-1 , + .resource = &flash_resource, + .num_resources =1 , + .dev = { + .platform_data = &flash_data, + }, +}; + +static struct resource i2c_resources[] = { + { + .start =MCFI2C_IOBASE , + .end =MCFI2C_IOBASE +0x40 , + .flags =IORESOURCE_MEM , + }, + { + .start =MCF_IRQ_I2C , + .end =MCF_IRQ_I2C , + .flags =IORESOURCE_IRQ , + }, +}; + +static struct platform_device i2c_device = {
arch/m68k/coldfire/amcore.c line 152
Quoted 10 lines
arch/m68k/coldfire/amcore.c new file +10
-0+ .name = "mcfi2c", + .id = 0, + .num_resources = ARRAY_SIZE(i2c_resources), + .resource = i2c_resources, +}; + +static void __init i2c_init (void ) +{ +writeb (MCFSIM_ICR_AUTOVEC |MCFSIM_ICR_LEVEL5 |MCFSIM_ICR_PRI0 , +MCF_MBAR +MCFSIM_I2CICR );
MCF_MBAR should not be added in here.
The current definition of your MCFSIM_I2CICR to MCFSIM_ICR3 is then "(MCF_MBAR + 0x4f)" in m5307sim.h. (This was not the case many years back, but it has been for a while now. If you just up-ported this patch from your 2.6 development work you might have missed this).
Quoted 192 lines
arch/m68k/coldfire/amcore.c new file +39
-0+mcf_mapirq2imr (MCF_IRQ_I2C ,MCFINTC_I2C ); +} + +static struct platform_device rtc_device = { + .name ="rtc-ds1307" , + .id =-1 , +}; + +static struct i2c_board_info amcore_i2c_info[]__initdata = { + { +I2C_BOARD_INFO ("ds1338" ,0x68 ), + }, +}; + +static struct platform_device *amcore_devices[] __initdata = { +#if defined(CONFIG_DM9000 ) || defined(CONFIG_DM9000_MODULE ) + &dm9000_device, +#endif + &flash_device, + &rtc_device, + &i2c_device, +}; + +static int __init init_amcore (void ) +{ +dm9000_pre_init (); + +/* Add i2c RTC Dallas chip supprt */ +i2c_register_board_info (0 , amcore_i2c_info, +ARRAY_SIZE (amcore_i2c_info)); + +platform_add_devices (amcore_devices,ARRAY_SIZE (amcore_devices)); + +i2c_init (); + +return 0 ; +} + +arch_initcall (init_amcore);arch/m68k/configs/amcore_defconfig new file +114
-0@@ -0,0 +1,114 @@ +CONFIG_LOCALVERSION="amcore-001" +CONFIG_DEFAULT_HOSTNAME="amcore" +CONFIG_SYSVIPC=y +# CONFIG_FHANDLE is not set +# CONFIG_USELIB is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +# CONFIG_AIO is not set +# CONFIG_ADVISE_SYSCALLS is not set +# CONFIG_MEMBARRIER is not set +CONFIG_EMBEDDED=y +# CONFIG_VM_EVENT_COUNTERS is not set +# CONFIG_COMPAT_BRK is not set +# CONFIG_LBDAF is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_MMU is not set +CONFIG_M5307=y +CONFIG_AMCORE=y +CONFIG_UBOOT=y +CONFIG_RAMSIZE=0x1000000 +CONFIG_KERNELBASE=0x20000 +CONFIG_NOMMU_INITIAL_TRIM_EXCESS=0 +CONFIG_BINFMT_FLAT=y +# CONFIG_COREDUMP is not set +CONFIG_NET=y +CONFIG_PACKET=y +CONFIG_UNIX=y +CONFIG_INET=y +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_IPV6 is not set +# CONFIG_WIRELESS is not set +# CONFIG_UEVENT_HELPER is not set +CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y +# CONFIG_ALLOW_DEV_COREDUMP is not set +CONFIG_CONNECTOR=y +CONFIG_MTD=y +CONFIG_MTD_BLOCK=y +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_LE_BYTE_SWAP=y +CONFIG_MTD_CFI_GEOMETRY=y +# CONFIG_MTD_CFI_I2 is not set +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_STAA=y +CONFIG_MTD_ROM=y +CONFIG_MTD_COMPLEX_MAPPINGS=y +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_UCLINUX=y +CONFIG_MTD_PLATRAM=y +CONFIG_BLK_DEV_RAM=y +CONFIG_NETDEVICES=y +# CONFIG_NET_VENDOR_ARC is not set +# CONFIG_NET_CADENCE is not set +# CONFIG_NET_VENDOR_BROADCOM is not set +CONFIG_DM9000=y +# CONFIG_NET_VENDOR_EZCHIP is not set +# CONFIG_NET_VENDOR_INTEL is not set +# CONFIG_NET_VENDOR_MARVELL is not set +# CONFIG_NET_VENDOR_MICREL is not set +# CONFIG_NET_VENDOR_NATSEMI is not set +# CONFIG_NET_VENDOR_NETRONOME is not set +# CONFIG_NET_VENDOR_QUALCOMM is not set +# CONFIG_NET_VENDOR_RENESAS is not set +# CONFIG_NET_VENDOR_ROCKER is not set +# CONFIG_NET_VENDOR_SAMSUNG is not set +# CONFIG_NET_VENDOR_SEEQ is not set +# CONFIG_NET_VENDOR_SMSC is not set +# CONFIG_NET_VENDOR_STMICRO is not set +# CONFIG_NET_VENDOR_SYNOPSYS is not set +# CONFIG_NET_VENDOR_VIA is not set +# CONFIG_NET_VENDOR_WIZNET is not set +# CONFIG_WLAN is not set +# CONFIG_INPUT is not set +# CONFIG_SERIO is not set +# CONFIG_VT is not set +# CONFIG_UNIX98_PTYS is not set +# CONFIG_DEVMEM is not set +# CONFIG_DEVKMEM is not set +CONFIG_SERIAL_MCF=y +CONFIG_SERIAL_MCF_BAUDRATE=115200 +CONFIG_SERIAL_MCF_CONSOLE=y +# CONFIG_HW_RANDOM is not set +CONFIG_I2C=y +# CONFIG_I2C_COMPAT is not set +# CONFIG_I2C_HELPER_AUTO is not set +CONFIG_PPS=y +# CONFIG_HWMON is not set +# CONFIG_USB_SUPPORT is not set +CONFIG_RTC_CLASS=y +CONFIG_EXT2_FS=y +CONFIG_EXT2_FS_XATTR=y +# CONFIG_FILE_LOCKING is not set +# CONFIG_DNOTIFY is not set +# CONFIG_INOTIFY_USER is not set +CONFIG_FSCACHE=y +# CONFIG_PROC_SYSCTL is not set +# CONFIG_SYSFS is not set +CONFIG_JFFS2_FS=y +CONFIG_ROMFS_FS=y +CONFIG_ROMFS_BACKED_BY_BOTH=y +# CONFIG_NETWORK_FILESYSTEMS is not set +CONFIG_PRINTK_TIME=y +# CONFIG_ENABLE_WARN_DEPRECATED is not set +# CONFIG_SECTION_MISMATCH_WARN_ONLY is not set +CONFIG_PANIC_ON_OOPS=y +# CONFIG_SCHED_DEBUG is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_CRYPTO_ECHAINIV is not set +CONFIG_CRYPTO_ANSI_CPRNG=y +# CONFIG_CRYPTO_HW is not set +CONFIG_CRC16=yarch/m68k/include/asm/m5307sim.h +7
-0@@ -131,6 +131,11 @@#define MCFGPIO_IRQ_MAX -1#define MCFGPIO_IRQ_VECBASE -1 +/* +* I2C module. +*/ +#define MCFI2C_IOBASE (MCF_MBAR + 0x280) +/* Definition offset address for CS2-7 -- old mask 5307 */ @@ -148,6 +153,7 @@#define MCFSIM_SWDICR MCFSIM_ICR0/* Watchdog timer ICR */ #define MCFSIM_TIMER1ICR MCFSIM_ICR1/* Timer 1 ICR */ #define MCFSIM_TIMER2ICR MCFSIM_ICR2/* Timer 2 ICR */ +#define MCFSIM_I2CICR MCFSIM_ICR3/* I2C ICR */ #define MCFSIM_UART1ICR MCFSIM_ICR4/* UART 1 ICR */ #define MCFSIM_UART2ICR MCFSIM_ICR5/* UART 2 ICR */ #define MCFSIM_DMA0ICR MCFSIM_ICR6/* DMA 0 ICR */ @@ -174,6 +180,7 @@/* * Define system peripheral IRQ usage. */ +#define MCF_IRQ_I2C 29/* I2C */ #define MCF_IRQ_TIMER 30/* Timer0, Level 6 */ #define MCF_IRQ_PROFILER 31/* Timer1, Level 7 */ #define MCF_IRQ_UART0 73/* UART0 */
Hi Greg,
many thanks for the prompt review,
Quoted 10 lines · Greg Ungerer
Hi Angelo,
Quoted 3 lines · Angelo Dureghello
Add support for Sysam AMCORE board, an open hardware embedded Linux board, see http://sysam.it/openzone/projects/amcore/amcore.html for any info.
Some comments below inline. My comments assume this patch was generated against a current or recent Linux head kernel. But I am not sure if that is the case?
yes, i started from mainline master, pulled last status yesterday, this since i would finally like to see the board support into mainline. I can work of course in the linux-m68k repo as well, just let me know the more correct way.
Quoted 7 lines
What bus driver does this use for i2c?
Steven King had a patch set a couple of years back that did full ColdFire i2c support - but the sticking point was the i2c bus driver was not acceptable to the i2c driver folks.
Quoted 9 lines
But, the ColdFire platform part was good, and I have had a patch that contains just those parts sitting in my m68knommu git tree awaiting testing and some motivation to push it up-stream.
https://git.kernel.org/cgit/linux/kernel/git/gerg/m68knommu.git/commit/?h=i2c
Of course it is not terribly useful without i2c driver support. The mcfi2c include in this patch may need to be removed for one thing.
mainly i developed this board some years ago, and realized that without any attempt to add related support to Linux, things get lost on the way, and it's exactly what's happened.
I used i2c for a Dallas RTC, and it was working:
ds1307 module init
i2c-core: driver [rtc-ds1307] registered
i2c /dev entries driver
i2c-core: driver [dev_driver] registered
i2c i2c-0: adapter [mcfi2c.0] registered
rtc-ds1307 0-0068: probe
i2c i2c-0: master_xfer[0] W, addr=0x68, len=1
i2c i2c-0: master_xfer[1] R, addr=0x68, len=8
ds1338: dev (254:0)
rtc-ds1307 0-0068: rtc core: registered ds1338 as rtc0
rtc-ds1307 0-0068: 56 bytes nvram
i2c i2c-0: client [ds1338] registered with bus id 0-0068
i2c-dev: adapter [mcfi2c.0] registered as minor 0
mcfi2c mcfi2c.0: Coldfire I2C bus driver
TCP cubic registered
NET: Registered protocol family 17
i2c i2c-0: master_xfer[0] W, addr=0x68, len=1
i2c i2c-0: master_xfer[1] R, addr=0x68, len=7
rtc-ds1307 0-0068: read: 13 04 23 06 16 09 11
rtc-ds1307 0-0068: read secs=13, mins=4, hours=23, mday=16, mon=8, year=111, wday=5 rtc-ds1307 0-0068: setting system clock to 2011-09-16 23:04:13 UTC (1316214253)
But seems i can't find now the related changes i used. No problem, i can leave out the i2c part for now, and i would work to add it in a second future step, ok ?
Ok to fix all issues below in a v.2.
Quoted 419 lines
Quoted 55 lines
Signed-off-by Angelo Dureghello <[email protected]>--- arch/m68k/Kconfig.machine | 6 ++ arch/m68k/coldfire/Makefile | 1 + arch/m68k/coldfire/amcore.c | 191 +++++++++++++++++++++++++++++++++++++ arch/m68k/configs/amcore_defconfig | 114 ++++++++++++++++++++++ arch/m68k/include/asm/m5307sim.h | 7 ++ 5 files changed, 319 insertions(+) create mode 100644 arch/m68k/coldfire/amcore.c create mode 100644 arch/m68k/configs/amcore_defconfigarch/m68k/Kconfig.machine +6
-0@@ -259,6 +259,12 @@ config M5407C3 help Support for the Motorola M5407C3 board. +config AMCORE + bool "Sysam AMCORE board support" + depends on M5307 + help + Support for the Sysam AMCORE open-hardware generic board. + config FIREBEE bool "FireBee board support" depends on M547xarch/m68k/coldfire/Makefile +1
-0@@ -34,6 +34,7 @@ obj-$(CONFIG_NETtel) += nettel.o obj-$(CONFIG_CLEOPATRA) += nettel.o obj-$(CONFIG_FIREBEE) += firebee.o obj-$(CONFIG_MCF8390) += mcf8390.o +obj-$(CONFIG_AMCORE) += amcore.o obj-$(CONFIG_PCI) += pci.oarch/m68k/coldfire/amcore.c new file +8
-0@@ -0,0 +1,191 @@ +/* +* amcore.c -- Support for Sysam AMCORE open board +* +* (C) Copyright 2016, Angelo Dureghello <[email protected]> +* +* This file is subject to the terms and conditions of the GNU General Public +* License. See the file COPYING in the main directory of this archive +* for more details. arch/m68k/coldfire/amcore.c line 18
Quoted 10 lines
arch/m68k/coldfire/amcore.c new file +10
-0+*/ + +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/dm9000.h> + +#include <linux/irq.h> +#include <linux/interrupt.h> + +#ifdef CONFIG_COLDFIRE This file can only be compiled for a ColdFire (in fact only 5307 based on your
Kconfig.machineandMakefilechanges). No need to wrap it in an "#ifdef".arch/m68k/coldfire/amcore.c line 29
Quoted 11 lines
arch/m68k/coldfire/amcore.c new file +11
-0+#include <asm/coldfire.h> +#include <asm/mcfsim.h> +#endif + +#include <asm/io.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/map.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> +#include <linux/i2c.h> +#include <asm/m5307sim.h> No need to include
m5307sim.h, it is included frommcfsim.h.Normal practice is to list all the linux/*.h includes first, then the asm/*.h includes.
arch/m68k/coldfire/amcore.c line 34
Quoted 4 lines
arch/m68k/coldfire/amcore.c new file +4
-0+/* +* Name the Board for the /proc/cpuinfo +*/ +const char cf_board_name[] ="Sysam AMCORE" ;This doesn't appear to be used?
arch/m68k/coldfire/amcore.c line 35
Quoted 2 lines
arch/m68k/coldfire/amcore.c new file +2
-0+ +#if defined(CONFIG_DM9000 ) || defined(CONFIG_DM9000_MODULE )#if
IS_ENABLED(CONFIG_DM9000)Quoted 105 lines
arch/m68k/coldfire/amcore.c new file +105
-0+#define DM9000_IRQ 25 +#define DM9000_ADDR 0x30000000 + +/* +* DEVICES and related device RESOURCES +*/ +static struct resource dm9000_resources[] = { +/* physical address of the address register (CMD [A2] to 0)*/ + [0 ] = { + .start =DM9000_ADDR , + .end =DM9000_ADDR +3 , + .flags =IORESOURCE_MEM , + }, +/* physical address of the data register (CMD [A2] to 1)*/ + [1 ] = { + .start =DM9000_ADDR +4 , + .end =DM9000_ADDR +4 +0xff , + .flags =IORESOURCE_MEM , + }, +/* IRQ line the device's interrupt pin is connected to */ + [2 ] = { + .start =DM9000_IRQ , + .end =DM9000_IRQ , + .flags =IORESOURCE_IRQ , + }, +}; + +static struct dm9000_plat_data dm9000_platdata = { + .flags =DM9000_PLATF_32BITONLY , +}; + +static struct platform_device dm9000_device = { + .name ="dm9000" , + .id =0 , + .num_resources =ARRAY_SIZE (dm9000_resources), + .resource = dm9000_resources, + .dev = { + .platform_data = &dm9000_platdata, + } +}; +#endif + +static void __init dm9000_pre_init (void ) +{ +/* Set the dm9000 interrupt to be auto-vectored */ +mcf_autovector (DM9000_IRQ ); +} + +/* +* Partitioning of parallel NOR flash (39VF3201B) +*/ +static struct mtd_partition amcore_partitions[] = { +{ + .name ="U-Boot (128K)" , + .size =0x20000 , + .offset =0x0 +}, +{ + .name ="Kernel+ROMfs (2994K)" , + .size =0x2E0000 , + .offset =MTDPART_OFS_APPEND +}, +{ + .name ="Flash Free Space (1024K)" , + .size =MTDPART_SIZ_FULL , + .offset =MTDPART_OFS_APPEND +} +}; + +static struct physmap_flash_data flash_data = { + .parts = amcore_partitions, + .nr_parts =ARRAY_SIZE (amcore_partitions), + .width =2 , +}; + +static struct resource flash_resource = { + .start =0xffc00000 , + .end =0xffffffff , + .flags =IORESOURCE_MEM , +}; + +static struct platform_device flash_device = { + .name ="physmap-flash" , + .id =-1 , + .resource = &flash_resource, + .num_resources =1 , + .dev = { + .platform_data = &flash_data, + }, +}; + +static struct resource i2c_resources[] = { + { + .start =MCFI2C_IOBASE , + .end =MCFI2C_IOBASE +0x40 , + .flags =IORESOURCE_MEM , + }, + { + .start =MCF_IRQ_I2C , + .end =MCF_IRQ_I2C , + .flags =IORESOURCE_IRQ , + }, +}; + +static struct platform_device i2c_device = {arch/m68k/coldfire/amcore.c line 152
Quoted 10 lines
arch/m68k/coldfire/amcore.c new file +10
-0+ .name = "mcfi2c", + .id = 0, + .num_resources = ARRAY_SIZE(i2c_resources), + .resource = i2c_resources, +}; + +static void __init i2c_init (void ) +{ +writeb (MCFSIM_ICR_AUTOVEC |MCFSIM_ICR_LEVEL5 |MCFSIM_ICR_PRI0 , +MCF_MBAR +MCFSIM_I2CICR );
MCF_MBARshould not be added in here.
The current definition of yourMCFSIM_I2CICRtoMCFSIM_ICR3is then "(MCF_MBAR+0x4f)" inm5307sim.h. (This was not the case many years back, but it has been for a while now. If you just up-ported this patch from your 2.6 development work you might have missed this).Quoted 192 lines
arch/m68k/coldfire/amcore.c new file +39
-0+mcf_mapirq2imr (MCF_IRQ_I2C ,MCFINTC_I2C ); +} + +static struct platform_device rtc_device = { + .name ="rtc-ds1307" , + .id =-1 , +}; + +static struct i2c_board_info amcore_i2c_info[]__initdata = { + { +I2C_BOARD_INFO ("ds1338" ,0x68 ), + }, +}; + +static struct platform_device *amcore_devices[] __initdata = { +#if defined(CONFIG_DM9000 ) || defined(CONFIG_DM9000_MODULE ) + &dm9000_device, +#endif + &flash_device, + &rtc_device, + &i2c_device, +}; + +static int __init init_amcore (void ) +{ +dm9000_pre_init (); + +/* Add i2c RTC Dallas chip supprt */ +i2c_register_board_info (0 , amcore_i2c_info, +ARRAY_SIZE (amcore_i2c_info)); + +platform_add_devices (amcore_devices,ARRAY_SIZE (amcore_devices)); + +i2c_init (); + +return 0 ; +} + +arch_initcall (init_amcore);arch/m68k/configs/amcore_defconfig new file +114
-0@@ -0,0 +1,114 @@ +CONFIG_LOCALVERSION="amcore-001" +CONFIG_DEFAULT_HOSTNAME="amcore" +CONFIG_SYSVIPC=y +# CONFIG_FHANDLE is not set +# CONFIG_USELIB is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +# CONFIG_AIO is not set +# CONFIG_ADVISE_SYSCALLS is not set +# CONFIG_MEMBARRIER is not set +CONFIG_EMBEDDED=y +# CONFIG_VM_EVENT_COUNTERS is not set +# CONFIG_COMPAT_BRK is not set +# CONFIG_LBDAF is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_MMU is not set +CONFIG_M5307=y +CONFIG_AMCORE=y +CONFIG_UBOOT=y +CONFIG_RAMSIZE=0x1000000 +CONFIG_KERNELBASE=0x20000 +CONFIG_NOMMU_INITIAL_TRIM_EXCESS=0 +CONFIG_BINFMT_FLAT=y +# CONFIG_COREDUMP is not set +CONFIG_NET=y +CONFIG_PACKET=y +CONFIG_UNIX=y +CONFIG_INET=y +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_IPV6 is not set +# CONFIG_WIRELESS is not set +# CONFIG_UEVENT_HELPER is not set +CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y +# CONFIG_ALLOW_DEV_COREDUMP is not set +CONFIG_CONNECTOR=y +CONFIG_MTD=y +CONFIG_MTD_BLOCK=y +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_LE_BYTE_SWAP=y +CONFIG_MTD_CFI_GEOMETRY=y +# CONFIG_MTD_CFI_I2 is not set +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_STAA=y +CONFIG_MTD_ROM=y +CONFIG_MTD_COMPLEX_MAPPINGS=y +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_UCLINUX=y +CONFIG_MTD_PLATRAM=y +CONFIG_BLK_DEV_RAM=y +CONFIG_NETDEVICES=y +# CONFIG_NET_VENDOR_ARC is not set +# CONFIG_NET_CADENCE is not set +# CONFIG_NET_VENDOR_BROADCOM is not set +CONFIG_DM9000=y +# CONFIG_NET_VENDOR_EZCHIP is not set +# CONFIG_NET_VENDOR_INTEL is not set +# CONFIG_NET_VENDOR_MARVELL is not set +# CONFIG_NET_VENDOR_MICREL is not set +# CONFIG_NET_VENDOR_NATSEMI is not set +# CONFIG_NET_VENDOR_NETRONOME is not set +# CONFIG_NET_VENDOR_QUALCOMM is not set +# CONFIG_NET_VENDOR_RENESAS is not set +# CONFIG_NET_VENDOR_ROCKER is not set +# CONFIG_NET_VENDOR_SAMSUNG is not set +# CONFIG_NET_VENDOR_SEEQ is not set +# CONFIG_NET_VENDOR_SMSC is not set +# CONFIG_NET_VENDOR_STMICRO is not set +# CONFIG_NET_VENDOR_SYNOPSYS is not set +# CONFIG_NET_VENDOR_VIA is not set +# CONFIG_NET_VENDOR_WIZNET is not set +# CONFIG_WLAN is not set +# CONFIG_INPUT is not set +# CONFIG_SERIO is not set +# CONFIG_VT is not set +# CONFIG_UNIX98_PTYS is not set +# CONFIG_DEVMEM is not set +# CONFIG_DEVKMEM is not set +CONFIG_SERIAL_MCF=y +CONFIG_SERIAL_MCF_BAUDRATE=115200 +CONFIG_SERIAL_MCF_CONSOLE=y +# CONFIG_HW_RANDOM is not set +CONFIG_I2C=y +# CONFIG_I2C_COMPAT is not set +# CONFIG_I2C_HELPER_AUTO is not set +CONFIG_PPS=y +# CONFIG_HWMON is not set +# CONFIG_USB_SUPPORT is not set +CONFIG_RTC_CLASS=y +CONFIG_EXT2_FS=y +CONFIG_EXT2_FS_XATTR=y +# CONFIG_FILE_LOCKING is not set +# CONFIG_DNOTIFY is not set +# CONFIG_INOTIFY_USER is not set +CONFIG_FSCACHE=y +# CONFIG_PROC_SYSCTL is not set +# CONFIG_SYSFS is not set +CONFIG_JFFS2_FS=y +CONFIG_ROMFS_FS=y +CONFIG_ROMFS_BACKED_BY_BOTH=y +# CONFIG_NETWORK_FILESYSTEMS is not set +CONFIG_PRINTK_TIME=y +# CONFIG_ENABLE_WARN_DEPRECATED is not set +# CONFIG_SECTION_MISMATCH_WARN_ONLY is not set +CONFIG_PANIC_ON_OOPS=y +# CONFIG_SCHED_DEBUG is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_CRYPTO_ECHAINIV is not set +CONFIG_CRYPTO_ANSI_CPRNG=y +# CONFIG_CRYPTO_HW is not set +CONFIG_CRC16=yarch/m68k/include/asm/m5307sim.h +7
-0@@ -131,6 +131,11 @@#define MCFGPIO_IRQ_MAX -1#define MCFGPIO_IRQ_VECBASE -1 +/* +* I2C module. +*/ +#define MCFI2C_IOBASE (MCF_MBAR + 0x280) +/* Definition offset address for CS2-7 -- old mask 5307 */ @@ -148,6 +153,7 @@#define MCFSIM_SWDICR MCFSIM_ICR0/* Watchdog timer ICR */ #define MCFSIM_TIMER1ICR MCFSIM_ICR1/* Timer 1 ICR */ #define MCFSIM_TIMER2ICR MCFSIM_ICR2/* Timer 2 ICR */ +#define MCFSIM_I2CICR MCFSIM_ICR3/* I2C ICR */ #define MCFSIM_UART1ICR MCFSIM_ICR4/* UART 1 ICR */ #define MCFSIM_UART2ICR MCFSIM_ICR5/* UART 2 ICR */ #define MCFSIM_DMA0ICR MCFSIM_ICR6/* DMA 0 ICR */ @@ -174,6 +180,7 @@/* * Define system peripheral IRQ usage. */ +#define MCF_IRQ_I2C 29/* I2C */ #define MCF_IRQ_TIMER 30/* Timer0, Level 6 */ #define MCF_IRQ_PROFILER 31/* Timer1, Level 7 */ #define MCF_IRQ_UART0 73/* UART0 */
Greg Ungerer
maintainerHi Angelo,
Quoted 11 lines · Angelo Dureghello
Hi Greg,
many thanks for the prompt review,Quoted 7 lines · Greg Ungerer
Hi Angelo,
Quoted 3 lines · Angelo Dureghello
Add support for Sysam AMCORE board, an open hardware embedded Linux board, see http://sysam.it/openzone/projects/amcore/amcore.html for any info.
Quoted 8 lines
Quoted 3 lines
Some comments below inline. My comments assume this patch was generated against a current or recent Linux head kernel. But I am not sure if that is the case?
yes, i started from mainline master, pulled last status yesterday, this since i would finally like to see the board support into mainline. I can work of course in the linux-m68k repo as well, just let me know the more correct way.
Mainline master is definitely best, so that is good.
Quoted 49 lines
Quoted 11 lines
What bus driver does this use for i2c?
Steven King had a patch set a couple of years back that did full ColdFire i2c support - but the sticking point was the i2c bus driver was not acceptable to the i2c driver folks.
But, the ColdFire platform part was good, and I have had a patch that contains just those parts sitting in my m68knommu git tree awaiting testing and some motivation to push it up-stream.
Quoted 6 lines
https://git.kernel.org/cgit/linux/kernel/git/gerg/m68knommu.git/commit/?h=i2c
Of course it is not terribly useful without i2c driver support. The mcfi2c include in this patch may need to be removed for one thing.
mainly i developed this board some years ago, and realized that without any attempt to add related support to Linux, things get lost on the way, and it's exactly what's happened.
I used i2c for a Dallas RTC, and it was working:
ds1307 module init
i2c-core: driver [rtc-ds1307] registered
i2c /dev entries driver
i2c-core: driver [dev_driver] registered
i2c i2c-0: adapter [mcfi2c.0] registered
rtc-ds1307 0-0068: probe
i2c i2c-0: master_xfer[0] W, addr=0x68, len=1
i2c i2c-0: master_xfer[1] R, addr=0x68, len=8
ds1338: dev (254:0)
rtc-ds1307 0-0068: rtc core: registered ds1338 as rtc0 rtc-ds1307 0-0068: 56 bytes nvram
i2c i2c-0: client [ds1338] registered with bus id 0-0068
i2c-dev: adapter [mcfi2c.0] registered as minor 0 mcfi2c mcfi2c.0: Coldfire I2C bus driver
TCP cubic registered
NET: Registered protocol family 17
i2c i2c-0: master_xfer[0] W, addr=0x68, len=1
i2c i2c-0: master_xfer[1] R, addr=0x68, len=7 rtc-ds1307 0-0068: read: 13 04 23 06 16 09 11 rtc-ds1307 0-0068: read secs=13, mins=4, hours=23, mday=16, mon=8, year=111, wday=5
rtc-ds1307 0-0068: setting system clock to 2011-09-16 23:04:13 UTC (1316214253)
Quoted 2 lines
But seems i can't find now the related changes i used. No problem, i can leave out the i2c part for now, and i would work
Was the above trace from your older kernel?
Or with current master head?
A bit of googling and you find find Steven Kings i2c driver for ColdFire. This is one version of it that I recall:
http://mailman.uclinux.org/pipermail/uclinux-dev/2012-May/051874.html
Anyway, I recall that the issue is that the ColdFire i2c hardware module is very similar to the Freescale iMX i2c hardware module. And the i2c maintainers didn't want a separate i2c-coldfire.c - the imx i2c driver should be modified to support it in both cores.
Quoted 1 line
to add it in a second future step, ok ?
Yep, no problem at all. If you can build on that i2c Coldfire patch I reference that would be ideal. It covers i2c on all ColdFire SoC that have it, so it is a good base. And that would test that patch and I can push that to mainline too.
Quoted 1 line
Ok to fix all issues below in a v.2.
I don't see any problem with the base you have. So cleaned up should be no problem to pull in.
Regards
Greg
Quoted 423 lines
Quoted 422 lines
Quoted 57 lines
Signed-off-by Angelo Dureghello <[email protected]>--- arch/m68k/Kconfig.machine | 6 ++ arch/m68k/coldfire/Makefile | 1 + arch/m68k/coldfire/amcore.c | 191 +++++++++++++++++++++++++++++++++++++ arch/m68k/configs/amcore_defconfig | 114 ++++++++++++++++++++++ arch/m68k/include/asm/m5307sim.h | 7 ++ 5 files changed, 319 insertions(+) create mode 100644 arch/m68k/coldfire/amcore.c create mode 100644 arch/m68k/configs/amcore_defconfigarch/m68k/Kconfig.machine +6
-0@@ -259,6 +259,12 @@ config M5407C3 help Support for the Motorola M5407C3 board. +config AMCORE + bool "Sysam AMCORE board support" + depends on M5307 + help + Support for the Sysam AMCORE open-hardware generic board. + config FIREBEE bool "FireBee board support" depends on M547xarch/m68k/coldfire/Makefile +1
-0@@ -34,6 +34,7 @@ obj-$(CONFIG_NETtel) += nettel.o obj-$(CONFIG_CLEOPATRA) += nettel.o obj-$(CONFIG_FIREBEE) += firebee.o obj-$(CONFIG_MCF8390) += mcf8390.o +obj-$(CONFIG_AMCORE) += amcore.o obj-$(CONFIG_PCI) += pci.oarch/m68k/coldfire/amcore.c new file +6
-0@@ -0,0 +1,191 @@ +/* +* amcore.c -- Support for Sysam AMCORE open board +* +* (C) Copyright 2016, Angelo Dureghello <[email protected]> +* +* This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file COPYING in the main directory of this archive
+ * for more details.
+ */arch/m68k/coldfire/amcore.c line 18
Quoted 9 lines
arch/m68k/coldfire/amcore.c new file +9
-0+ +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/dm9000.h> + +#include <linux/irq.h> +#include <linux/interrupt.h> + +#ifdef CONFIG_COLDFIRE This file can only be compiled for a ColdFire (in fact only 5307 based on your
Kconfig.machineandMakefilechanges). No need to wrap it in an "#ifdef".arch/m68k/coldfire/amcore.c line 29
Quoted 11 lines
arch/m68k/coldfire/amcore.c new file +11
-0+#include <asm/coldfire.h> +#include <asm/mcfsim.h> +#endif + +#include <asm/io.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/map.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> +#include <linux/i2c.h> +#include <asm/m5307sim.h> No need to include
m5307sim.h, it is included frommcfsim.h.Normal practice is to list all the linux/*.h includes first, then the asm/*.h includes.
arch/m68k/coldfire/amcore.c line 34
Quoted 4 lines
arch/m68k/coldfire/amcore.c new file +4
-0+/* +* Name the Board for the /proc/cpuinfo +*/ +const char cf_board_name[] ="Sysam AMCORE" ;This doesn't appear to be used?
arch/m68k/coldfire/amcore.c
Quoted 2 lines
arch/m68k/coldfire/amcore.c new file +2
-0+ +#if defined(CONFIG_DM9000 ) || defined(CONFIG_DM9000_MODULE )#if
IS_ENABLED(CONFIG_DM9000)Quoted 105 lines
arch/m68k/coldfire/amcore.c new file +105
-0+#define DM9000_IRQ 25 +#define DM9000_ADDR 0x30000000 + +/* +* DEVICES and related device RESOURCES +*/ +static struct resource dm9000_resources[] = { +/* physical address of the address register (CMD [A2] to 0)*/ + [0 ] = { + .start =DM9000_ADDR , + .end =DM9000_ADDR +3 , + .flags =IORESOURCE_MEM , + }, +/* physical address of the data register (CMD [A2] to 1)*/ + [1 ] = { + .start =DM9000_ADDR +4 , + .end =DM9000_ADDR +4 +0xff , + .flags =IORESOURCE_MEM , + }, +/* IRQ line the device's interrupt pin is connected to */ + [2 ] = { + .start =DM9000_IRQ , + .end =DM9000_IRQ , + .flags =IORESOURCE_IRQ , + }, +}; + +static struct dm9000_plat_data dm9000_platdata = { + .flags =DM9000_PLATF_32BITONLY , +}; + +static struct platform_device dm9000_device = { + .name ="dm9000" , + .id =0 , + .num_resources =ARRAY_SIZE (dm9000_resources), + .resource = dm9000_resources, + .dev = { + .platform_data = &dm9000_platdata, + } +}; +#endif + +static void __init dm9000_pre_init (void ) +{ +/* Set the dm9000 interrupt to be auto-vectored */ +mcf_autovector (DM9000_IRQ ); +} + +/* +* Partitioning of parallel NOR flash (39VF3201B) +*/ +static struct mtd_partition amcore_partitions[] = { +{ + .name ="U-Boot (128K)" , + .size =0x20000 , + .offset =0x0 +}, +{ + .name ="Kernel+ROMfs (2994K)" , + .size =0x2E0000 , + .offset =MTDPART_OFS_APPEND +}, +{ + .name ="Flash Free Space (1024K)" , + .size =MTDPART_SIZ_FULL , + .offset =MTDPART_OFS_APPEND +} +}; + +static struct physmap_flash_data flash_data = { + .parts = amcore_partitions, + .nr_parts =ARRAY_SIZE (amcore_partitions), + .width =2 , +}; + +static struct resource flash_resource = { + .start =0xffc00000 , + .end =0xffffffff , + .flags =IORESOURCE_MEM , +}; + +static struct platform_device flash_device = { + .name ="physmap-flash" , + .id =-1 , + .resource = &flash_resource, + .num_resources =1 , + .dev = { + .platform_data = &flash_data, + }, +}; + +static struct resource i2c_resources[] = { + { + .start =MCFI2C_IOBASE , + .end =MCFI2C_IOBASE +0x40 , + .flags =IORESOURCE_MEM , + }, + { + .start =MCF_IRQ_I2C , + .end =MCF_IRQ_I2C , + .flags =IORESOURCE_IRQ , + }, +}; + +static struct platform_device i2c_device = {arch/m68k/coldfire/amcore.c line 152
Quoted 10 lines
arch/m68k/coldfire/amcore.c new file +10
-0+ .name = "mcfi2c", + .id = 0, + .num_resources = ARRAY_SIZE(i2c_resources), + .resource = i2c_resources, +}; + +static void __init i2c_init (void ) +{ +writeb (MCFSIM_ICR_AUTOVEC |MCFSIM_ICR_LEVEL5 |MCFSIM_ICR_PRI0 , +MCF_MBAR +MCFSIM_I2CICR );
MCF_MBARshould not be added in here.
The current definition of yourMCFSIM_I2CICRtoMCFSIM_ICR3is then "(MCF_MBAR+0x4f)" inm5307sim.h. (This was not the case many years back, but it has been for a while now. If you just up-ported this patch from your 2.6 development work you might have missed this).Quoted 194 lines
arch/m68k/coldfire/amcore.c new file +39
-0+mcf_mapirq2imr (MCF_IRQ_I2C ,MCFINTC_I2C ); +} + +static struct platform_device rtc_device = { + .name ="rtc-ds1307" , + .id =-1 , +}; + +static struct i2c_board_info amcore_i2c_info[]__initdata = { + { +I2C_BOARD_INFO ("ds1338" ,0x68 ), + }, +}; + +static struct platform_device *amcore_devices[] __initdata = { +#if defined(CONFIG_DM9000 ) || defined(CONFIG_DM9000_MODULE ) + &dm9000_device, +#endif + &flash_device, + &rtc_device, + &i2c_device, +}; + +static int __init init_amcore (void ) +{ +dm9000_pre_init (); + +/* Add i2c RTC Dallas chip supprt */ +i2c_register_board_info (0 , amcore_i2c_info, +ARRAY_SIZE (amcore_i2c_info)); + +platform_add_devices (amcore_devices,ARRAY_SIZE (amcore_devices)); + +i2c_init (); + +return 0 ; +} + +arch_initcall (init_amcore);arch/m68k/configs/amcore_defconfig new file +114
-0@@ -0,0 +1,114 @@ +CONFIG_LOCALVERSION="amcore-001" +CONFIG_DEFAULT_HOSTNAME="amcore" +CONFIG_SYSVIPC=y +# CONFIG_FHANDLE is not set +# CONFIG_USELIB is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +# CONFIG_AIO is not set +# CONFIG_ADVISE_SYSCALLS is not set +# CONFIG_MEMBARRIER is not set +CONFIG_EMBEDDED=y +# CONFIG_VM_EVENT_COUNTERS is not set +# CONFIG_COMPAT_BRK is not set +# CONFIG_LBDAF is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_MMU is not set +CONFIG_M5307=y +CONFIG_AMCORE=y +CONFIG_UBOOT=y +CONFIG_RAMSIZE=0x1000000 +CONFIG_KERNELBASE=0x20000 +CONFIG_NOMMU_INITIAL_TRIM_EXCESS=0 +CONFIG_BINFMT_FLAT=y +# CONFIG_COREDUMP is not set +CONFIG_NET=y +CONFIG_PACKET=y +CONFIG_UNIX=y +CONFIG_INET=y +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_IPV6 is not set +# CONFIG_WIRELESS is not set +# CONFIG_UEVENT_HELPER is not set +CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y +# CONFIG_ALLOW_DEV_COREDUMP is not set +CONFIG_CONNECTOR=y +CONFIG_MTD=y +CONFIG_MTD_BLOCK=y +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_LE_BYTE_SWAP=y +CONFIG_MTD_CFI_GEOMETRY=y +# CONFIG_MTD_CFI_I2 is not set +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_STAA=y +CONFIG_MTD_ROM=y +CONFIG_MTD_COMPLEX_MAPPINGS=y +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_UCLINUX=y +CONFIG_MTD_PLATRAM=y +CONFIG_BLK_DEV_RAM=y +CONFIG_NETDEVICES=y +# CONFIG_NET_VENDOR_ARC is not set +# CONFIG_NET_CADENCE is not set +# CONFIG_NET_VENDOR_BROADCOM is not set +CONFIG_DM9000=y +# CONFIG_NET_VENDOR_EZCHIP is not set +# CONFIG_NET_VENDOR_INTEL is not set +# CONFIG_NET_VENDOR_MARVELL is not set +# CONFIG_NET_VENDOR_MICREL is not set +# CONFIG_NET_VENDOR_NATSEMI is not set +# CONFIG_NET_VENDOR_NETRONOME is not set +# CONFIG_NET_VENDOR_QUALCOMM is not set +# CONFIG_NET_VENDOR_RENESAS is not set +# CONFIG_NET_VENDOR_ROCKER is not set +# CONFIG_NET_VENDOR_SAMSUNG is not set +# CONFIG_NET_VENDOR_SEEQ is not set +# CONFIG_NET_VENDOR_SMSC is not set +# CONFIG_NET_VENDOR_STMICRO is not set +# CONFIG_NET_VENDOR_SYNOPSYS is not set +# CONFIG_NET_VENDOR_VIA is not set +# CONFIG_NET_VENDOR_WIZNET is not set +# CONFIG_WLAN is not set +# CONFIG_INPUT is not set +# CONFIG_SERIO is not set +# CONFIG_VT is not set +# CONFIG_UNIX98_PTYS is not set +# CONFIG_DEVMEM is not set +# CONFIG_DEVKMEM is not set +CONFIG_SERIAL_MCF=y +CONFIG_SERIAL_MCF_BAUDRATE=115200 +CONFIG_SERIAL_MCF_CONSOLE=y +# CONFIG_HW_RANDOM is not set +CONFIG_I2C=y +# CONFIG_I2C_COMPAT is not set +# CONFIG_I2C_HELPER_AUTO is not set +CONFIG_PPS=y +# CONFIG_HWMON is not set +# CONFIG_USB_SUPPORT is not set +CONFIG_RTC_CLASS=y +CONFIG_EXT2_FS=y +CONFIG_EXT2_FS_XATTR=y +# CONFIG_FILE_LOCKING is not set +# CONFIG_DNOTIFY is not set +# CONFIG_INOTIFY_USER is not set +CONFIG_FSCACHE=y +# CONFIG_PROC_SYSCTL is not set +# CONFIG_SYSFS is not set +CONFIG_JFFS2_FS=y +CONFIG_ROMFS_FS=y +CONFIG_ROMFS_BACKED_BY_BOTH=y +# CONFIG_NETWORK_FILESYSTEMS is not set +CONFIG_PRINTK_TIME=y +# CONFIG_ENABLE_WARN_DEPRECATED is not set +# CONFIG_SECTION_MISMATCH_WARN_ONLY is not set +CONFIG_PANIC_ON_OOPS=y +# CONFIG_SCHED_DEBUG is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_CRYPTO_ECHAINIV is not set +CONFIG_CRYPTO_ANSI_CPRNG=y +# CONFIG_CRYPTO_HW is not set +CONFIG_CRC16=yarch/m68k/include/asm/m5307sim.h +7
-0@@ -131,6 +131,11 @@#define MCFGPIO_IRQ_MAX -1#define MCFGPIO_IRQ_VECBASE -1 +/* +* I2C module. +*/ +#define MCFI2C_IOBASE (MCF_MBAR + 0x280) +/* Definition offset address for CS2-7 -- old mask 5307 */ @@ -148,6 +153,7 @@#define MCFSIM_SWDICR MCFSIM_ICR0/* Watchdog timer ICR */ #define MCFSIM_TIMER1ICR MCFSIM_ICR1/* Timer 1 ICR */ #define MCFSIM_TIMER2ICR MCFSIM_ICR2/* Timer 2 ICR */ +#define MCFSIM_I2CICR MCFSIM_ICR3/* I2C ICR */ #define MCFSIM_UART1ICR MCFSIM_ICR4/* UART 1 ICR */ #define MCFSIM_UART2ICR MCFSIM_ICR5/* UART 2 ICR */ #define MCFSIM_DMA0ICR MCFSIM_ICR6/* DMA 0 ICR */ @@ -174,6 +180,7 @@/* * Define system peripheral IRQ usage. */ +#define MCF_IRQ_I2C 29/* I2C */ #define MCF_IRQ_TIMER 30/* Timer0, Level 6 */ #define MCF_IRQ_PROFILER 31/* Timer1, Level 7 */ #define MCF_IRQ_UART0 73/* UART0 */
Hi Greg,
Quoted 18 lines · Greg Ungerer
Hi Angelo,
Quoted 15 lines · Angelo Dureghello
Hi Greg,
many thanks for the prompt review,Quoted 10 lines · Greg Ungerer
Hi Angelo,
Quoted 3 lines · Angelo Dureghello
Add support for Sysam AMCORE board, an open hardware embedded Linux board, see http://sysam.it/openzone/projects/amcore/amcore.html for any info.
Some comments below inline. My comments assume this patch was generated against a current or recent Linux head kernel. But I am not sure if that is the case?
Quoted 8 lines
Quoted 4 lines
yes, i started from mainline master, pulled last status yesterday, this since i would finally like to see the board support into mainline. I can work of course in the linux-m68k repo as well, just let me know the more correct way.
Mainline master is definitely best, so that is good.
perfect.
Quoted 67 lines
Quoted 49 lines
Quoted 11 lines
What bus driver does this use for i2c?
Steven King had a patch set a couple of years back that did full ColdFire i2c support - but the sticking point was the i2c bus driver was not acceptable to the i2c driver folks.
But, the ColdFire platform part was good, and I have had a patch that contains just those parts sitting in my m68knommu git tree awaiting testing and some motivation to push it up-stream.
Quoted 6 lines
https://git.kernel.org/cgit/linux/kernel/git/gerg/m68knommu.git/commit/?h=i2c
Of course it is not terribly useful without i2c driver support. The mcfi2c include in this patch may need to be removed for one thing.
mainly i developed this board some years ago, and realized that without any attempt to add related support to Linux, things get lost on the way, and it's exactly what's happened.
I used i2c for a Dallas RTC, and it was working:
ds1307 module init
i2c-core: driver [rtc-ds1307] registered
i2c /dev entries driver
i2c-core: driver [dev_driver] registered
i2c i2c-0: adapter [mcfi2c.0] registered
rtc-ds1307 0-0068: probe
i2c i2c-0: master_xfer[0] W, addr=0x68, len=1
i2c i2c-0: master_xfer[1] R, addr=0x68, len=8
ds1338: dev (254:0)
rtc-ds1307 0-0068: rtc core: registered ds1338 as rtc0 rtc-ds1307 0-0068: 56 bytes nvram
i2c i2c-0: client [ds1338] registered with bus id 0-0068
i2c-dev: adapter [mcfi2c.0] registered as minor 0 mcfi2c mcfi2c.0: Coldfire I2C bus driver
TCP cubic registered
NET: Registered protocol family 17
i2c i2c-0: master_xfer[0] W, addr=0x68, len=1
i2c i2c-0: master_xfer[1] R, addr=0x68, len=7 rtc-ds1307 0-0068: read: 13 04 23 06 16 09 11 rtc-ds1307 0-0068: read secs=13, mins=4, hours=23, mday=16, mon=8, year=111, wday=5
rtc-ds1307 0-0068: setting system clock to 2011-09-16 23:04:13 UTC (1316214253)Quoted 2 lines
But seems i can't find now the related changes i used. No problem, i can leave out the i2c part for now, and i would work
Was the above trace from your older kernel?
Or with current master head?A bit of googling and you find find Steven Kings i2c driver for ColdFire. This is one version of it that I recall:
http://mailman.uclinux.org/pipermail/uclinux-dev/2012-May/051874.html
Anyway, I recall that the issue is that the ColdFire i2c hardware module is very similar to the Freescale iMX i2c hardware module. And the i2c maintainers didn't want a separate
i2c-coldfire.c- the imx i2c driver should be modified to support it in both cores.
Quoted 8 lines
Quoted 1 line
to add it in a second future step, ok ?
Yep, no problem at all. If you can build on that i2c Coldfire patch I reference that would be ideal. It covers i2c on all ColdFire SoC that have it, so it is a good base. And that would test that patch and I can push that to mainline too.
I finally could have the driver working in 4.8. Yes, as you have seen, i used the Steven King driver that i updated now to work with the last mainline.
U-Boot 2016.09-00092-g1ba96b1-dirty (Sep 20 2016 - 17:51:47)
CPU: Freescale Coldfire MCF5307 at 90 MHz DRAM: 16 MiB Flash: 4 MiB Hit any key to stop autoboot: 0 ## Booting kernel from Legacy Image at ffc20000 ... Image Name: mainline kernel Image Type: M68K Linux Kernel Image (uncompressed) Data Size: 2914308 Bytes = 2.8 MiB Load Address: 00020000 Entry Point: 00020000 Verifying Checksum ... OK Loading Kernel Image ... OK [ 0.000000] Linux version 4.8.0-rc8amcore-001-00013-g53061af-dirty (angelo@jerusalem) (gcc version 4.9.0 (crosstools-sysam-2016.04.16) ) #2 Fri Sep 30 01:56:50 CEST 2016 [ 0.000000] [ 0.000000] [ 0.000000] uClinux/COLDFIRE(m5307) [ 0.000000] COLDFIRE port done by Greg Ungerer, [email protected] [ 0.000000] Modified for M5307 by Dave Miller, [email protected]
...
[ 1.090000] i2c /dev entries driver
[ 1.110000] rtc-ds1307 0-0068: rtc core: registered ds1338 as rtc0
[ 1.110000] rtc-ds1307 0-0068: 56 bytes nvram
[ 1.120000] mcfi2c mcfi2c.0: Coldfire I2C bus driver
[ 1.120000] NET: Registered protocol family 17
[ 1.140000] rtc-ds1307 0-0068: setting system clock to
2000-01-01 06:27:17 UTC (946708037)
[ 1.160000] VFS: Mounted root (romfs filesystem) readonly on device 31:3.
[ 1.170000] Freeing unused kernel memory: 56K (0021a000 - 00228000)
[ 1.170000] This architecture does not have kernel memory protection.But still have an issue with the hwclock tool (not busybux), for some reason can't apply rtc time:
~ # hwclock --hctosysRTC_RD_TIME: Invalid argumentioctl() to /dev/rtc to read the time failed.
~ # hwclock --hctosys -D
hwclock 2.4c/util-linux-2.11a
Using /dev/rtc interface to clock.
Assuming hardware clock is kept in local time.
Waiting for clock tick.../dev/rtc does not have interrupt functions. Waiting in loop for time
from /dev/rtc to changeRTC_RD_TIME: Invalid argumentioctl() to /dev/rtc to read the time failed.
The hw part seems sane, so should be able to fix this later today. All other issues below are fixed.
Then i would send a 2/2 patchset, one for the board support and other for i2c.
Regards,
Angelo Dureghello
Quoted 434 lines
Quoted 1 line
Ok to fix all issues below in a v.2.
I don't see any problem with the base you have. So cleaned up should be no problem to pull in.
Regards
GregQuoted 423 lines
Quoted 422 lines
Quoted 57 lines
Signed-off-by Angelo Dureghello <[email protected]>--- arch/m68k/Kconfig.machine | 6 ++ arch/m68k/coldfire/Makefile | 1 + arch/m68k/coldfire/amcore.c | 191 +++++++++++++++++++++++++++++++++++++ arch/m68k/configs/amcore_defconfig | 114 ++++++++++++++++++++++ arch/m68k/include/asm/m5307sim.h | 7 ++ 5 files changed, 319 insertions(+) create mode 100644 arch/m68k/coldfire/amcore.c create mode 100644 arch/m68k/configs/amcore_defconfigarch/m68k/Kconfig.machine +6
-0@@ -259,6 +259,12 @@ config M5407C3 help Support for the Motorola M5407C3 board. +config AMCORE + bool "Sysam AMCORE board support" + depends on M5307 + help + Support for the Sysam AMCORE open-hardware generic board. + config FIREBEE bool "FireBee board support" depends on M547xarch/m68k/coldfire/Makefile +1
-0@@ -34,6 +34,7 @@ obj-$(CONFIG_NETtel) += nettel.o obj-$(CONFIG_CLEOPATRA) += nettel.o obj-$(CONFIG_FIREBEE) += firebee.o obj-$(CONFIG_MCF8390) += mcf8390.o +obj-$(CONFIG_AMCORE) += amcore.o obj-$(CONFIG_PCI) += pci.oarch/m68k/coldfire/amcore.c new file +6
-0@@ -0,0 +1,191 @@ +/* +* amcore.c -- Support for Sysam AMCORE open board +* +* (C) Copyright 2016, Angelo Dureghello <[email protected]> +* +* This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file COPYING in the main directory of this archive
+ * for more details.
+ */arch/m68k/coldfire/amcore.c line 18
Quoted 9 lines
arch/m68k/coldfire/amcore.c new file +9
-0+ +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/dm9000.h> + +#include <linux/irq.h> +#include <linux/interrupt.h> + +#ifdef CONFIG_COLDFIRE This file can only be compiled for a ColdFire (in fact only 5307 based on your
Kconfig.machineandMakefilechanges). No need to wrap it in an "#ifdef".arch/m68k/coldfire/amcore.c line 29
Quoted 11 lines
arch/m68k/coldfire/amcore.c new file +11
-0+#include <asm/coldfire.h> +#include <asm/mcfsim.h> +#endif + +#include <asm/io.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/map.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> +#include <linux/i2c.h> +#include <asm/m5307sim.h> No need to include
m5307sim.h, it is included frommcfsim.h.Normal practice is to list all the linux/*.h includes first, then the asm/*.h includes.
arch/m68k/coldfire/amcore.c line 34
Quoted 4 lines
arch/m68k/coldfire/amcore.c new file +4
-0+/* +* Name the Board for the /proc/cpuinfo +*/ +const char cf_board_name[] ="Sysam AMCORE" ;This doesn't appear to be used?
arch/m68k/coldfire/amcore.c
Quoted 2 lines
arch/m68k/coldfire/amcore.c new file +2
-0+ +#if defined(CONFIG_DM9000 ) || defined(CONFIG_DM9000_MODULE )#if
IS_ENABLED(CONFIG_DM9000)Quoted 105 lines
arch/m68k/coldfire/amcore.c new file +105
-0+#define DM9000_IRQ 25 +#define DM9000_ADDR 0x30000000 + +/* +* DEVICES and related device RESOURCES +*/ +static struct resource dm9000_resources[] = { +/* physical address of the address register (CMD [A2] to 0)*/ + [0 ] = { + .start =DM9000_ADDR , + .end =DM9000_ADDR +3 , + .flags =IORESOURCE_MEM , + }, +/* physical address of the data register (CMD [A2] to 1)*/ + [1 ] = { + .start =DM9000_ADDR +4 , + .end =DM9000_ADDR +4 +0xff , + .flags =IORESOURCE_MEM , + }, +/* IRQ line the device's interrupt pin is connected to */ + [2 ] = { + .start =DM9000_IRQ , + .end =DM9000_IRQ , + .flags =IORESOURCE_IRQ , + }, +}; + +static struct dm9000_plat_data dm9000_platdata = { + .flags =DM9000_PLATF_32BITONLY , +}; + +static struct platform_device dm9000_device = { + .name ="dm9000" , + .id =0 , + .num_resources =ARRAY_SIZE (dm9000_resources), + .resource = dm9000_resources, + .dev = { + .platform_data = &dm9000_platdata, + } +}; +#endif + +static void __init dm9000_pre_init (void ) +{ +/* Set the dm9000 interrupt to be auto-vectored */ +mcf_autovector (DM9000_IRQ ); +} + +/* +* Partitioning of parallel NOR flash (39VF3201B) +*/ +static struct mtd_partition amcore_partitions[] = { +{ + .name ="U-Boot (128K)" , + .size =0x20000 , + .offset =0x0 +}, +{ + .name ="Kernel+ROMfs (2994K)" , + .size =0x2E0000 , + .offset =MTDPART_OFS_APPEND +}, +{ + .name ="Flash Free Space (1024K)" , + .size =MTDPART_SIZ_FULL , + .offset =MTDPART_OFS_APPEND +} +}; + +static struct physmap_flash_data flash_data = { + .parts = amcore_partitions, + .nr_parts =ARRAY_SIZE (amcore_partitions), + .width =2 , +}; + +static struct resource flash_resource = { + .start =0xffc00000 , + .end =0xffffffff , + .flags =IORESOURCE_MEM , +}; + +static struct platform_device flash_device = { + .name ="physmap-flash" , + .id =-1 , + .resource = &flash_resource, + .num_resources =1 , + .dev = { + .platform_data = &flash_data, + }, +}; + +static struct resource i2c_resources[] = { + { + .start =MCFI2C_IOBASE , + .end =MCFI2C_IOBASE +0x40 , + .flags =IORESOURCE_MEM , + }, + { + .start =MCF_IRQ_I2C , + .end =MCF_IRQ_I2C , + .flags =IORESOURCE_IRQ , + }, +}; + +static struct platform_device i2c_device = {arch/m68k/coldfire/amcore.c line 152
Quoted 10 lines
arch/m68k/coldfire/amcore.c new file +10
-0+ .name = "mcfi2c", + .id = 0, + .num_resources = ARRAY_SIZE(i2c_resources), + .resource = i2c_resources, +}; + +static void __init i2c_init (void ) +{ +writeb (MCFSIM_ICR_AUTOVEC |MCFSIM_ICR_LEVEL5 |MCFSIM_ICR_PRI0 , +MCF_MBAR +MCFSIM_I2CICR );
MCF_MBARshould not be added in here.
The current definition of yourMCFSIM_I2CICRtoMCFSIM_ICR3is then "(MCF_MBAR+0x4f)" inm5307sim.h. (This was not the case many years back, but it has been for a while now. If you just up-ported this patch from your 2.6 development work you might have missed this).Quoted 194 lines
arch/m68k/coldfire/amcore.c new file +39
-0+mcf_mapirq2imr (MCF_IRQ_I2C ,MCFINTC_I2C ); +} + +static struct platform_device rtc_device = { + .name ="rtc-ds1307" , + .id =-1 , +}; + +static struct i2c_board_info amcore_i2c_info[]__initdata = { + { +I2C_BOARD_INFO ("ds1338" ,0x68 ), + }, +}; + +static struct platform_device *amcore_devices[] __initdata = { +#if defined(CONFIG_DM9000 ) || defined(CONFIG_DM9000_MODULE ) + &dm9000_device, +#endif + &flash_device, + &rtc_device, + &i2c_device, +}; + +static int __init init_amcore (void ) +{ +dm9000_pre_init (); + +/* Add i2c RTC Dallas chip supprt */ +i2c_register_board_info (0 , amcore_i2c_info, +ARRAY_SIZE (amcore_i2c_info)); + +platform_add_devices (amcore_devices,ARRAY_SIZE (amcore_devices)); + +i2c_init (); + +return 0 ; +} + +arch_initcall (init_amcore);arch/m68k/configs/amcore_defconfig new file +114
-0@@ -0,0 +1,114 @@ +CONFIG_LOCALVERSION="amcore-001" +CONFIG_DEFAULT_HOSTNAME="amcore" +CONFIG_SYSVIPC=y +# CONFIG_FHANDLE is not set +# CONFIG_USELIB is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +# CONFIG_AIO is not set +# CONFIG_ADVISE_SYSCALLS is not set +# CONFIG_MEMBARRIER is not set +CONFIG_EMBEDDED=y +# CONFIG_VM_EVENT_COUNTERS is not set +# CONFIG_COMPAT_BRK is not set +# CONFIG_LBDAF is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_MMU is not set +CONFIG_M5307=y +CONFIG_AMCORE=y +CONFIG_UBOOT=y +CONFIG_RAMSIZE=0x1000000 +CONFIG_KERNELBASE=0x20000 +CONFIG_NOMMU_INITIAL_TRIM_EXCESS=0 +CONFIG_BINFMT_FLAT=y +# CONFIG_COREDUMP is not set +CONFIG_NET=y +CONFIG_PACKET=y +CONFIG_UNIX=y +CONFIG_INET=y +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_IPV6 is not set +# CONFIG_WIRELESS is not set +# CONFIG_UEVENT_HELPER is not set +CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y +# CONFIG_ALLOW_DEV_COREDUMP is not set +CONFIG_CONNECTOR=y +CONFIG_MTD=y +CONFIG_MTD_BLOCK=y +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_LE_BYTE_SWAP=y +CONFIG_MTD_CFI_GEOMETRY=y +# CONFIG_MTD_CFI_I2 is not set +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_STAA=y +CONFIG_MTD_ROM=y +CONFIG_MTD_COMPLEX_MAPPINGS=y +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_UCLINUX=y +CONFIG_MTD_PLATRAM=y +CONFIG_BLK_DEV_RAM=y +CONFIG_NETDEVICES=y +# CONFIG_NET_VENDOR_ARC is not set +# CONFIG_NET_CADENCE is not set +# CONFIG_NET_VENDOR_BROADCOM is not set +CONFIG_DM9000=y +# CONFIG_NET_VENDOR_EZCHIP is not set +# CONFIG_NET_VENDOR_INTEL is not set +# CONFIG_NET_VENDOR_MARVELL is not set +# CONFIG_NET_VENDOR_MICREL is not set +# CONFIG_NET_VENDOR_NATSEMI is not set +# CONFIG_NET_VENDOR_NETRONOME is not set +# CONFIG_NET_VENDOR_QUALCOMM is not set +# CONFIG_NET_VENDOR_RENESAS is not set +# CONFIG_NET_VENDOR_ROCKER is not set +# CONFIG_NET_VENDOR_SAMSUNG is not set +# CONFIG_NET_VENDOR_SEEQ is not set +# CONFIG_NET_VENDOR_SMSC is not set +# CONFIG_NET_VENDOR_STMICRO is not set +# CONFIG_NET_VENDOR_SYNOPSYS is not set +# CONFIG_NET_VENDOR_VIA is not set +# CONFIG_NET_VENDOR_WIZNET is not set +# CONFIG_WLAN is not set +# CONFIG_INPUT is not set +# CONFIG_SERIO is not set +# CONFIG_VT is not set +# CONFIG_UNIX98_PTYS is not set +# CONFIG_DEVMEM is not set +# CONFIG_DEVKMEM is not set +CONFIG_SERIAL_MCF=y +CONFIG_SERIAL_MCF_BAUDRATE=115200 +CONFIG_SERIAL_MCF_CONSOLE=y +# CONFIG_HW_RANDOM is not set +CONFIG_I2C=y +# CONFIG_I2C_COMPAT is not set +# CONFIG_I2C_HELPER_AUTO is not set +CONFIG_PPS=y +# CONFIG_HWMON is not set +# CONFIG_USB_SUPPORT is not set +CONFIG_RTC_CLASS=y +CONFIG_EXT2_FS=y +CONFIG_EXT2_FS_XATTR=y +# CONFIG_FILE_LOCKING is not set +# CONFIG_DNOTIFY is not set +# CONFIG_INOTIFY_USER is not set +CONFIG_FSCACHE=y +# CONFIG_PROC_SYSCTL is not set +# CONFIG_SYSFS is not set +CONFIG_JFFS2_FS=y +CONFIG_ROMFS_FS=y +CONFIG_ROMFS_BACKED_BY_BOTH=y +# CONFIG_NETWORK_FILESYSTEMS is not set +CONFIG_PRINTK_TIME=y +# CONFIG_ENABLE_WARN_DEPRECATED is not set +# CONFIG_SECTION_MISMATCH_WARN_ONLY is not set +CONFIG_PANIC_ON_OOPS=y +# CONFIG_SCHED_DEBUG is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_CRYPTO_ECHAINIV is not set +CONFIG_CRYPTO_ANSI_CPRNG=y +# CONFIG_CRYPTO_HW is not set +CONFIG_CRC16=yarch/m68k/include/asm/m5307sim.h +7
-0@@ -131,6 +131,11 @@#define MCFGPIO_IRQ_MAX -1#define MCFGPIO_IRQ_VECBASE -1 +/* +* I2C module. +*/ +#define MCFI2C_IOBASE (MCF_MBAR + 0x280) +/* Definition offset address for CS2-7 -- old mask 5307 */ @@ -148,6 +153,7 @@#define MCFSIM_SWDICR MCFSIM_ICR0/* Watchdog timer ICR */ #define MCFSIM_TIMER1ICR MCFSIM_ICR1/* Timer 1 ICR */ #define MCFSIM_TIMER2ICR MCFSIM_ICR2/* Timer 2 ICR */ +#define MCFSIM_I2CICR MCFSIM_ICR3/* I2C ICR */ #define MCFSIM_UART1ICR MCFSIM_ICR4/* UART 1 ICR */ #define MCFSIM_UART2ICR MCFSIM_ICR5/* UART 2 ICR */ #define MCFSIM_DMA0ICR MCFSIM_ICR6/* DMA 0 ICR */ @@ -174,6 +180,7 @@/* * Define system peripheral IRQ usage. */ +#define MCF_IRQ_I2C 29/* I2C */ #define MCF_IRQ_TIMER 30/* Timer0, Level 6 */ #define MCF_IRQ_PROFILER 31/* Timer1, Level 7 */ #define MCF_IRQ_UART0 73/* UART0 */