Skip to contentSkip to conversation

i40e: use unsigned printf format specifier for active_filters count

PATCH New Bimmy Pujari 2 participants 11 messages Nov 14, 2016 – Nov 18, 2016

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/5 i40e: use unsigned printf format specifier for active_filters count

From: Jacob Keller <[email protected]>

Replace the %d specifier used for printing vsi->active_filters and vsi->promisc_threshold with an unsigned %u format specifier. While it is unlikely in practice that these values will ever reach such a large number they are unsigned values and thus should not be interpreted as negative numbers.

Change-ID Iff050fad5a1c8537c4c57fcd527441cd95cfc0d4

---
Testing-hints:
This should go upstream, even though it is in debugfs code. We're not adding features but simply correcting output of existing features.

 drivers/net/ethernet/intel/i40e/i40e_debugfs.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/intel/i40e/i40e_debugfs.c +1 -1
index b8a03a0..f1f41f1 100644
@@ -172,7 +172,7 @@ static void i40e_dbg_dump_vsi_seid(struct i40e_pf *pf, int seid)
 			 f->macaddr, f->vlan,
 			 i40e_filter_state_string[f->state]);
 	}
-	dev_info(&pf->pdev->dev, "    active_filters %d, promisc_threshold %d, overflow promisc %s\n",
+	dev_info(&pf->pdev->dev, "    active_filters %u, promisc_threshold %u, overflow promisc %s\n",
 		 vsi->active_filters, vsi->promisc_threshold,
 		 (test_bit(__I40E_FILTER_OVERFLOW_PROMISC, &vsi->state) ?
 		  "ON" : "OFF"));
Signature · 1 line
2.4.11
#1 lore raw

PATCH 2/5 i40e: Add support for 25G devices

From: Carolyn Wyborny <[email protected]>

Add support for 25G devices - defines and data structures.

One tricky part here is that the firmware support for these Devices introduces a mismatch between the PHY type enum and the bitfields for the phy types.

This change creates a macro and uses it to increment the 25G PHY values when creating 25G bitfields.

---
Testing Hints : Check that 25G devices link and report correct device speed.

 drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h  | 30 +++++++-
 drivers/net/ethernet/intel/i40e/i40e_common.c      | 11 ++-
 drivers/net/ethernet/intel/i40e/i40e_devids.h      |  2 +
 drivers/net/ethernet/intel/i40e/i40e_ethtool.c     | 20 +++++-
 drivers/net/ethernet/intel/i40e/i40e_main.c        |  6 +-
 drivers/net/ethernet/intel/i40e/i40e_type.h        | 82 +++++++++++++---------
 drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c |  3 +
 .../net/ethernet/intel/i40evf/i40e_adminq_cmd.h    | 30 +++++++-
 drivers/net/ethernet/intel/i40evf/i40e_common.c    |  2 +
 drivers/net/ethernet/intel/i40evf/i40e_devids.h    |  2 +
 drivers/net/ethernet/intel/i40evf/i40e_type.h      | 82 +++++++++++++---------
 drivers/net/ethernet/intel/i40evf/i40evf_ethtool.c |  8 +++
 .../net/ethernet/intel/i40evf/i40evf_virtchnl.c    |  3 +
 13 files changed, 202 insertions(+), 79 deletions(-)
drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h +27 -3
index 67e396b..c9d1f91 100644
@@ -1642,6 +1642,10 @@ enum i40e_aq_phy_type {
 	I40E_PHY_TYPE_1000BASE_LX		= 0x1C,
 	I40E_PHY_TYPE_1000BASE_T_OPTICAL	= 0x1D,
 	I40E_PHY_TYPE_20GBASE_KR2		= 0x1E,
+	I40E_PHY_TYPE_25GBASE_KR		= 0x1F,
+	I40E_PHY_TYPE_25GBASE_CR		= 0x20,
+	I40E_PHY_TYPE_25GBASE_SR		= 0x21,
+	I40E_PHY_TYPE_25GBASE_LR		= 0x22,
 	I40E_PHY_TYPE_MAX
 };
 
@@ -1650,6 +1654,7 @@ enum i40e_aq_phy_type {
 #define I40E_LINK_SPEED_10GB_SHIFT	0x3
 #define I40E_LINK_SPEED_40GB_SHIFT	0x4
 #define I40E_LINK_SPEED_20GB_SHIFT	0x5
+#define I40E_LINK_SPEED_25GB_SHIFT	0x6
 
 enum i40e_aq_link_speed {
 	I40E_LINK_SPEED_UNKNOWN	= 0,
@@ -1657,7 +1662,8 @@ enum i40e_aq_link_speed {
 	I40E_LINK_SPEED_1GB	= BIT(I40E_LINK_SPEED_1000MB_SHIFT),
 	I40E_LINK_SPEED_10GB	= BIT(I40E_LINK_SPEED_10GB_SHIFT),
 	I40E_LINK_SPEED_40GB	= BIT(I40E_LINK_SPEED_40GB_SHIFT),
-	I40E_LINK_SPEED_20GB	= BIT(I40E_LINK_SPEED_20GB_SHIFT)
+	I40E_LINK_SPEED_20GB	= BIT(I40E_LINK_SPEED_20GB_SHIFT),
+	I40E_LINK_SPEED_25GB	= BIT(I40E_LINK_SPEED_25GB_SHIFT),
 };
 
 struct i40e_aqc_module_desc {
@@ -1690,7 +1696,13 @@ struct i40e_aq_get_phy_abilities_resp {
 	__le32	eeer_val;
 	u8	d3_lpan;
 #define I40E_AQ_SET_PHY_D3_LPAN_ENA	0x01
-	u8	reserved[3];
+	u8	phy_type_ext;
+#define I40E_AQ_PHY_TYPE_EXT_25G_KR	0X01
+#define I40E_AQ_PHY_TYPE_EXT_25G_CR	0X02
+#define I40E_AQ_PHY_TYPE_EXT_25G_SR	0x04
+#define I40E_AQ_PHY_TYPE_EXT_25G_LR	0x08
+	u8	mod_type_ext;
+	u8	ext_comp_code;
 	u8	phy_id[4];
 	u8	module_type[3];
 	u8	qualified_module_count;
@@ -1712,7 +1724,12 @@ struct i40e_aq_set_phy_config { /* same bits as above in all */
 	__le16	eee_capability;
 	__le32	eeer;
 	u8	low_power_ctrl;
-	u8	reserved[3];
+	u8	phy_type_ext;
+#define I40E_AQ_PHY_TYPE_EXT_25G_KR	0X01
+#define I40E_AQ_PHY_TYPE_EXT_25G_CR	0X02
+#define I40E_AQ_PHY_TYPE_EXT_25G_SR	0x04
+#define I40E_AQ_PHY_TYPE_EXT_25G_LR	0x08
+	u8	reserved[2];
 };
 
 I40E_CHECK_CMD_LENGTH(i40e_aq_set_phy_config);
@@ -1792,6 +1809,13 @@ struct i40e_aqc_get_link_status {
 #define I40E_AQ_LINK_TX_DRAINED		0x01
 #define I40E_AQ_LINK_TX_FLUSHED		0x03
 #define I40E_AQ_LINK_FORCED_40G		0x10
+/* 25G Error Codes */
+#define I40E_AQ_25G_NO_ERR		0X00
+#define I40E_AQ_25G_NOT_PRESENT		0X01
+#define I40E_AQ_25G_NVM_CRC_ERR		0X02
+#define I40E_AQ_25G_SBUS_UCODE_ERR	0X03
+#define I40E_AQ_25G_SERDES_UCODE_ERR	0X04
+#define I40E_AQ_25G_NIMB_UCODE_ERR	0X05
 	u8	loopback; /* use defines from i40e_aqc_set_lb_mode */
 	__le16	max_frame_size;
 	u8	config;
drivers/net/ethernet/intel/i40e/i40e_common.c +10 -1
index d1dcd4f..3961fc2 100644
@@ -53,6 +53,8 @@ static i40e_status i40e_set_mac_type(struct i40e_hw *hw)
 		case I40E_DEV_ID_10G_BASE_T4:
 		case I40E_DEV_ID_20G_KR2:
 		case I40E_DEV_ID_20G_KR2_A:
+		case I40E_DEV_ID_25G_B:
+		case I40E_DEV_ID_25G_SFP28:
 			hw->mac.type = I40E_MAC_XL710;
 			break;
 		case I40E_DEV_ID_KX_X722:
@@ -1183,6 +1185,8 @@ static enum i40e_media_type i40e_get_media_type(struct i40e_hw *hw)
 	case I40E_PHY_TYPE_1000BASE_LX:
 	case I40E_PHY_TYPE_40GBASE_SR4:
 	case I40E_PHY_TYPE_40GBASE_LR4:
+	case I40E_PHY_TYPE_25GBASE_LR:
+	case I40E_PHY_TYPE_25GBASE_SR:
 		media = I40E_MEDIA_TYPE_FIBER;
 		break;
 	case I40E_PHY_TYPE_100BASE_TX:
@@ -1197,6 +1201,7 @@ static enum i40e_media_type i40e_get_media_type(struct i40e_hw *hw)
 	case I40E_PHY_TYPE_10GBASE_SFPP_CU:
 	case I40E_PHY_TYPE_40GBASE_AOC:
 	case I40E_PHY_TYPE_10GBASE_AOC:
+	case I40E_PHY_TYPE_25GBASE_CR:
 		media = I40E_MEDIA_TYPE_DA;
 		break;
 	case I40E_PHY_TYPE_1000BASE_KX:
@@ -1204,6 +1209,7 @@ static enum i40e_media_type i40e_get_media_type(struct i40e_hw *hw)
 	case I40E_PHY_TYPE_10GBASE_KR:
 	case I40E_PHY_TYPE_40GBASE_KR4:
 	case I40E_PHY_TYPE_20GBASE_KR2:
+	case I40E_PHY_TYPE_25GBASE_KR:
 		media = I40E_MEDIA_TYPE_BACKPLANE;
 		break;
 	case I40E_PHY_TYPE_SGMII:
@@ -1608,8 +1614,10 @@ i40e_status i40e_aq_get_phy_capabilities(struct i40e_hw *hw,
 	if (hw->aq.asq_last_status == I40E_AQ_RC_EIO)
 		status = I40E_ERR_UNKNOWN_PHY;
 
-	if (report_init)
+	if (report_init) {
 		hw->phy.phy_types = le32_to_cpu(abilities->phy_type);
+		hw->phy.phy_types |= ((u64)abilities->phy_type_ext << 32);
+	}
 
 	return status;
 }
@@ -1701,6 +1709,7 @@ enum i40e_status_code i40e_set_fc(struct i40e_hw *hw, u8 *aq_failures,
 			config.abilities |= I40E_AQ_PHY_ENABLE_ATOMIC_LINK;
 		/* Copy over all the old settings */
 		config.phy_type = abilities.phy_type;
+		config.phy_type_ext = abilities.phy_type_ext;
 		config.link_speed = abilities.link_speed;
 		config.eee_capability = abilities.eee_capability;
 		config.eeer = abilities.eeer_val;
drivers/net/ethernet/intel/i40e/i40e_devids.h +2 -0
index dd4457d..8e46098 100644
@@ -39,6 +39,8 @@
 #define I40E_DEV_ID_20G_KR2		0x1587
 #define I40E_DEV_ID_20G_KR2_A		0x1588
 #define I40E_DEV_ID_10G_BASE_T4		0x1589
+#define I40E_DEV_ID_25G_B		0x158A
+#define I40E_DEV_ID_25G_SFP28		0x158B
 #define I40E_DEV_ID_KX_X722		0x37CE
 #define I40E_DEV_ID_QSFP_X722		0x37CF
 #define I40E_DEV_ID_SFP_X722		0x37D0
drivers/net/ethernet/intel/i40e/i40e_ethtool.c +19 -1
index 6ba0035..4b3a71a 100644
@@ -265,8 +265,9 @@ static void i40e_partition_setting_complaint(struct i40e_pf *pf)
 static void i40e_phy_type_to_ethtool(struct i40e_pf *pf, u32 *supported,
 				     u32 *advertising)
 {
-	enum i40e_aq_capabilities_phy_type phy_types = pf->hw.phy.phy_types;
 	struct i40e_link_status *hw_link_info = &pf->hw.phy.link_info;
+	u64 phy_types = pf->hw.phy.phy_types;
+
 	*supported = 0x0;
 	*advertising = 0x0;
 
@@ -369,6 +370,15 @@ static void i40e_phy_type_to_ethtool(struct i40e_pf *pf, u32 *supported,
 			if (!(pf->flags & I40E_FLAG_HAVE_CRT_RETIMER))
 				*advertising |= ADVERTISED_1000baseKX_Full;
 	}
+	if (phy_types & I40E_CAP_PHY_TYPE_25GBASE_KR ||
+	    phy_types & I40E_CAP_PHY_TYPE_25GBASE_CR ||
+	    phy_types & I40E_CAP_PHY_TYPE_25GBASE_SR ||
+	    phy_types & I40E_CAP_PHY_TYPE_25GBASE_LR) {
+		*supported |= SUPPORTED_Autoneg |
+			     SUPPORTED_2500baseX_Full;
+		*advertising |= ADVERTISED_Autoneg |
+			       ADVERTISED_2500baseX_Full;
+	}
 }
 
 /**
@@ -491,6 +501,14 @@ static void i40e_get_settings_link_up(struct i40e_hw *hw,
 				     ADVERTISED_1000baseKX_Full |
 				     ADVERTISED_Autoneg;
 		break;
+	case I40E_PHY_TYPE_25GBASE_KR:
+	case I40E_PHY_TYPE_25GBASE_CR:
+	case I40E_PHY_TYPE_25GBASE_SR:
+	case I40E_PHY_TYPE_25GBASE_LR:
+		ecmd->supported |= SUPPORTED_2500baseX_Full |
+				   SUPPORTED_Autoneg;
+		ecmd->advertising |= ADVERTISED_2500baseX_Full |
+				     ADVERTISED_Autoneg;
 	default:
 		/* if we got here and link is up something bad is afoot */
 		netdev_info(netdev, "WARNING: Link is up but PHY type 0x%x is not recognized.\n",
drivers/net/ethernet/intel/i40e/i40e_main.c +5 -1
index a032dfd..849feaa 100644
@@ -86,6 +86,8 @@ static const struct pci_device_id i40e_pci_tbl[] = {
 	{PCI_VDEVICE(INTEL, I40E_DEV_ID_SFP_I_X722), 0},
 	{PCI_VDEVICE(INTEL, I40E_DEV_ID_20G_KR2), 0},
 	{PCI_VDEVICE(INTEL, I40E_DEV_ID_20G_KR2_A), 0},
+	{PCI_VDEVICE(INTEL, I40E_DEV_ID_25G_B), 0},
+	{PCI_VDEVICE(INTEL, I40E_DEV_ID_25G_SFP28), 0},
 	/* required last entry */
 	{0, }
 };
@@ -5248,6 +5250,9 @@ void i40e_print_link_message(struct i40e_vsi *vsi, bool isup)
 	case I40E_LINK_SPEED_20GB:
 		speed = "20 G";
 		break;
+	case I40E_LINK_SPEED_25GB:
+		speed = "25 G";
+		break;
 	case I40E_LINK_SPEED_10GB:
 		speed = "10 G";
 		break;
@@ -11356,7 +11361,6 @@ static int i40e_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 		dev_dbg(&pf->pdev->dev, "get supported phy types ret =  %s last_status =  %s\n",
 			i40e_stat_str(&pf->hw, err),
 			i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
-	pf->hw.phy.phy_types = le32_to_cpu(abilities.phy_type);
 
 	/* Add a filter to drop all Flow control frames from any VSI from being
 	 * transmitted. By doing so we stop a malicious VF from sending out
drivers/net/ethernet/intel/i40e/i40e_type.h +47 -35

94 lines not on this page · raw message

drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c +3 -0
index 05ed49b..d28b684 100644
@@ -2921,6 +2921,9 @@ int i40e_ndo_set_vf_bw(struct net_device *netdev, int vf_id, int min_tx_rate,
 	case I40E_LINK_SPEED_40GB:
 		speed = 40000;
 		break;
+	case I40E_LINK_SPEED_25GB:
+		speed = 25000;
+		break;
 	case I40E_LINK_SPEED_20GB:
 		speed = 20000;
 		break;
drivers/net/ethernet/intel/i40evf/i40e_adminq_cmd.h +27 -3
index 40b0eaf..f8d7d95 100644
@@ -1639,6 +1639,10 @@ enum i40e_aq_phy_type {
 	I40E_PHY_TYPE_1000BASE_LX		= 0x1C,
 	I40E_PHY_TYPE_1000BASE_T_OPTICAL	= 0x1D,
 	I40E_PHY_TYPE_20GBASE_KR2		= 0x1E,
+	I40E_PHY_TYPE_25GBASE_KR		= 0x1F,
+	I40E_PHY_TYPE_25GBASE_CR		= 0x20,
+	I40E_PHY_TYPE_25GBASE_SR		= 0x21,
+	I40E_PHY_TYPE_25GBASE_LR		= 0x22,
 	I40E_PHY_TYPE_MAX
 };
 
@@ -1647,6 +1651,7 @@ enum i40e_aq_phy_type {
 #define I40E_LINK_SPEED_10GB_SHIFT	0x3
 #define I40E_LINK_SPEED_40GB_SHIFT	0x4
 #define I40E_LINK_SPEED_20GB_SHIFT	0x5
+#define I40E_LINK_SPEED_25GB_SHIFT	0x6
 
 enum i40e_aq_link_speed {
 	I40E_LINK_SPEED_UNKNOWN	= 0,
@@ -1654,7 +1659,8 @@ enum i40e_aq_link_speed {
 	I40E_LINK_SPEED_1GB	= BIT(I40E_LINK_SPEED_1000MB_SHIFT),
 	I40E_LINK_SPEED_10GB	= BIT(I40E_LINK_SPEED_10GB_SHIFT),
 	I40E_LINK_SPEED_40GB	= BIT(I40E_LINK_SPEED_40GB_SHIFT),
-	I40E_LINK_SPEED_20GB	= BIT(I40E_LINK_SPEED_20GB_SHIFT)
+	I40E_LINK_SPEED_20GB	= BIT(I40E_LINK_SPEED_20GB_SHIFT),
+	I40E_LINK_SPEED_25GB	= BIT(I40E_LINK_SPEED_25GB_SHIFT),
 };
 
 struct i40e_aqc_module_desc {
@@ -1687,7 +1693,13 @@ struct i40e_aq_get_phy_abilities_resp {
 	__le32	eeer_val;
 	u8	d3_lpan;
 #define I40E_AQ_SET_PHY_D3_LPAN_ENA	0x01
-	u8	reserved[3];
+	u8	phy_type_ext;
+#define I40E_AQ_PHY_TYPE_EXT_25G_KR	0X01
+#define I40E_AQ_PHY_TYPE_EXT_25G_CR	0X02
+#define I40E_AQ_PHY_TYPE_EXT_25G_SR	0x04
+#define I40E_AQ_PHY_TYPE_EXT_25G_LR	0x08
+	u8	mod_type_ext;
+	u8	ext_comp_code;
 	u8	phy_id[4];
 	u8	module_type[3];
 	u8	qualified_module_count;
@@ -1709,7 +1721,12 @@ struct i40e_aq_set_phy_config { /* same bits as above in all */
 	__le16	eee_capability;
 	__le32	eeer;
 	u8	low_power_ctrl;
-	u8	reserved[3];
+	u8	phy_type_ext;
+#define I40E_AQ_PHY_TYPE_EXT_25G_KR	0X01
+#define I40E_AQ_PHY_TYPE_EXT_25G_CR	0X02
+#define I40E_AQ_PHY_TYPE_EXT_25G_SR	0x04
+#define I40E_AQ_PHY_TYPE_EXT_25G_LR	0x08
+	u8	reserved[2];
 };
 
 I40E_CHECK_CMD_LENGTH(i40e_aq_set_phy_config);
@@ -1789,6 +1806,13 @@ struct i40e_aqc_get_link_status {
 #define I40E_AQ_LINK_TX_DRAINED		0x01
 #define I40E_AQ_LINK_TX_FLUSHED		0x03
 #define I40E_AQ_LINK_FORCED_40G		0x10
+/* 25G Error Codes */
+#define I40E_AQ_25G_NO_ERR		0X00
+#define I40E_AQ_25G_NOT_PRESENT		0X01
+#define I40E_AQ_25G_NVM_CRC_ERR		0X02
+#define I40E_AQ_25G_SBUS_UCODE_ERR	0X03
+#define I40E_AQ_25G_SERDES_UCODE_ERR	0X04
+#define I40E_AQ_25G_NIMB_UCODE_ERR	0X05
 	u8	loopback; /* use defines from i40e_aqc_set_lb_mode */
 	__le16	max_frame_size;
 	u8	config;
drivers/net/ethernet/intel/i40evf/i40e_common.c +2 -0
index 7953c13..aa63b7f 100644
@@ -53,6 +53,8 @@ i40e_status i40e_set_mac_type(struct i40e_hw *hw)
 		case I40E_DEV_ID_10G_BASE_T4:
 		case I40E_DEV_ID_20G_KR2:
 		case I40E_DEV_ID_20G_KR2_A:
+		case I40E_DEV_ID_25G_B:
+		case I40E_DEV_ID_25G_SFP28:
 			hw->mac.type = I40E_MAC_XL710;
 			break;
 		case I40E_DEV_ID_SFP_X722:
drivers/net/ethernet/intel/i40evf/i40e_devids.h +2 -0
index 7023570..21dcaee 100644
@@ -39,6 +39,8 @@
 #define I40E_DEV_ID_20G_KR2		0x1587
 #define I40E_DEV_ID_20G_KR2_A		0x1588
 #define I40E_DEV_ID_10G_BASE_T4		0x1589
+#define I40E_DEV_ID_25G_B		0x158A
+#define I40E_DEV_ID_25G_SFP28		0x158B
 #define I40E_DEV_ID_VF			0x154C
 #define I40E_DEV_ID_VF_HV		0x1571
 #define I40E_DEV_ID_SFP_X722		0x37D0
drivers/net/ethernet/intel/i40evf/i40e_type.h +47 -35

94 lines not on this page · raw message

drivers/net/ethernet/intel/i40evf/i40evf_ethtool.c +8 -0
index a994015..272d600 100644
@@ -85,6 +85,14 @@ static int i40evf_get_settings(struct net_device *netdev,
 	case I40E_LINK_SPEED_40GB:
 		ethtool_cmd_speed_set(ecmd, SPEED_40000);
 		break;
+	case I40E_LINK_SPEED_25GB:
+#ifdef SPEED_25000
+		ethtool_cmd_speed_set(ecmd, SPEED_25000);
+#else
+		netdev_info(netdev,
+			    "Speed is 25G, display not supported by this version of ethtool.\n");
+#endif
+		break;
 	case I40E_LINK_SPEED_20GB:
 		ethtool_cmd_speed_set(ecmd, SPEED_20000);
 		break;
drivers/net/ethernet/intel/i40evf/i40evf_virtchnl.c +3 -0
index ddf478d..2059a8e 100644
@@ -836,6 +836,9 @@ static void i40evf_print_link_message(struct i40evf_adapter *adapter)
 	case I40E_LINK_SPEED_40GB:
 		speed = "40 G";
 		break;
+	case I40E_LINK_SPEED_25GB:
+		speed = "25 G";
+		break;
 	case I40E_LINK_SPEED_20GB:
 		speed = "20 G";
 		break;
Signature · 1 line
2.4.11
#2 lore raw

PATCH 2/5 i40e: Add support for 25G devices

Quoted 12 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On Behalf Of Bimmy Pujari
Sent: Monday, November 14, 2016 1:07 PM
To: intel-wired-lan at lists.osuosl.org
Cc: Tieman, Henry W <[email protected]>; Joyner, Eric <[email protected]>; Kosiarz, Michal <[email protected]>
Subject: [Intel-wired-lan] [next PATCH S53-V2 2/5] i40e: Add support for 25G devices

From: Carolyn Wyborny <[email protected]>

Quoted 8 lines

Add support for 25G devices - defines and data structures.

One tricky part here is that the firmware support for these Devices introduces a mismatch between the PHY type enum and the bitfields for the phy types.

This change creates a macro and uses it to increment the 25G PHY values when creating 25G bitfields.

25G devices identified correctly, show correct link speed, and pass traffic correctly

#3 lore raw

PATCH 3/5 i40e: Add FEC for 25g

In reply to Bimmy Pujari

From: Carolyn Wyborny <[email protected]>

This patch adds adminq support for Forward Error Correction ("FEC")for 25g products.

Change-ID Iaff4910737c239d2c730e5c22a313ce9c37d3964
---
 drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h  | 25 ++++++++++++++++++++--
 drivers/net/ethernet/intel/i40e/i40e_common.c      |  2 ++
 .../net/ethernet/intel/i40evf/i40e_adminq_cmd.h    | 25 ++++++++++++++++++++--
 3 files changed, 48 insertions(+), 4 deletions(-)
drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h +23 -2
index c9d1f91..b2101a5 100644
@@ -1686,6 +1686,8 @@ struct i40e_aq_get_phy_abilities_resp {
 #define I40E_AQ_PHY_LINK_ENABLED	0x08
 #define I40E_AQ_PHY_AN_ENABLED		0x10
 #define I40E_AQ_PHY_FLAG_MODULE_QUAL	0x20
+#define I40E_AQ_PHY_FEC_ABILITY_KR	0x40
+#define I40E_AQ_PHY_FEC_ABILITY_RS	0x80
 	__le16	eee_capability;
 #define I40E_AQ_EEE_100BASE_TX		0x0002
 #define I40E_AQ_EEE_1000BASE_T		0x0004
@@ -1701,7 +1703,16 @@ struct i40e_aq_get_phy_abilities_resp {
 #define I40E_AQ_PHY_TYPE_EXT_25G_CR	0X02
 #define I40E_AQ_PHY_TYPE_EXT_25G_SR	0x04
 #define I40E_AQ_PHY_TYPE_EXT_25G_LR	0x08
-	u8	mod_type_ext;
+	u8	fec_cfg_curr_mod_ext_info;
+#define I40E_AQ_ENABLE_FEC_KR		0x01
+#define I40E_AQ_ENABLE_FEC_RS		0x02
+#define I40E_AQ_REQUEST_FEC_KR		0x04
+#define I40E_AQ_REQUEST_FEC_RS		0x08
+#define I40E_AQ_ENABLE_FEC_AUTO		0x10
+#define I40E_AQ_FEC
+#define I40E_AQ_MODULE_TYPE_EXT_MASK	0xE0
+#define I40E_AQ_MODULE_TYPE_EXT_SHIFT	5
+
 	u8	ext_comp_code;
 	u8	phy_id[4];
 	u8	module_type[3];
@@ -1729,7 +1740,15 @@ struct i40e_aq_set_phy_config { /* same bits as above in all */
 #define I40E_AQ_PHY_TYPE_EXT_25G_CR	0X02
 #define I40E_AQ_PHY_TYPE_EXT_25G_SR	0x04
 #define I40E_AQ_PHY_TYPE_EXT_25G_LR	0x08
-	u8	reserved[2];
+	u8	fec_config;
+#define I40E_AQ_SET_FEC_ABILITY_KR	BIT(0)
+#define I40E_AQ_SET_FEC_ABILITY_RS	BIT(1)
+#define I40E_AQ_SET_FEC_REQUEST_KR	BIT(2)
+#define I40E_AQ_SET_FEC_REQUEST_RS	BIT(3)
+#define I40E_AQ_SET_FEC_AUTO		BIT(4)
+#define I40E_AQ_PHY_FEC_CONFIG_SHIFT	0x0
+#define I40E_AQ_PHY_FEC_CONFIG_MASK	(0x1F << I40E_AQ_PHY_FEC_CONFIG_SHIFT)
+	u8	reserved;
 };
 
 I40E_CHECK_CMD_LENGTH(i40e_aq_set_phy_config);
@@ -1819,6 +1838,8 @@ struct i40e_aqc_get_link_status {
 	u8	loopback; /* use defines from i40e_aqc_set_lb_mode */
 	__le16	max_frame_size;
 	u8	config;
+#define I40E_AQ_CONFIG_FEC_KR_ENA	0x01
+#define I40E_AQ_CONFIG_FEC_RS_ENA	0x02
 #define I40E_AQ_CONFIG_CRC_ENA		0x04
 #define I40E_AQ_CONFIG_PACING_MASK	0x78
 	u8	external_power_ability;
drivers/net/ethernet/intel/i40e/i40e_common.c +2 -0
index 3961fc2..d9da786 100644
@@ -1714,6 +1714,8 @@ enum i40e_status_code i40e_set_fc(struct i40e_hw *hw, u8 *aq_failures,
 		config.eee_capability = abilities.eee_capability;
 		config.eeer = abilities.eeer_val;
 		config.low_power_ctrl = abilities.d3_lpan;
+		config.fec_config = abilities.fec_cfg_curr_mod_ext_info &
+				    I40E_AQ_PHY_FEC_CONFIG_MASK;
 		status = i40e_aq_set_phy_config(hw, &config, NULL);
 
 		if (status)
drivers/net/ethernet/intel/i40evf/i40e_adminq_cmd.h +23 -2
index f8d7d95..eeb9864 100644
@@ -1683,6 +1683,8 @@ struct i40e_aq_get_phy_abilities_resp {
 #define I40E_AQ_PHY_LINK_ENABLED	0x08
 #define I40E_AQ_PHY_AN_ENABLED		0x10
 #define I40E_AQ_PHY_FLAG_MODULE_QUAL	0x20
+#define I40E_AQ_PHY_FEC_ABILITY_KR	0x40
+#define I40E_AQ_PHY_FEC_ABILITY_RS	0x80
 	__le16	eee_capability;
 #define I40E_AQ_EEE_100BASE_TX		0x0002
 #define I40E_AQ_EEE_1000BASE_T		0x0004
@@ -1698,7 +1700,16 @@ struct i40e_aq_get_phy_abilities_resp {
 #define I40E_AQ_PHY_TYPE_EXT_25G_CR	0X02
 #define I40E_AQ_PHY_TYPE_EXT_25G_SR	0x04
 #define I40E_AQ_PHY_TYPE_EXT_25G_LR	0x08
-	u8	mod_type_ext;
+	u8	fec_cfg_curr_mod_ext_info;
+#define I40E_AQ_ENABLE_FEC_KR		0x01
+#define I40E_AQ_ENABLE_FEC_RS		0x02
+#define I40E_AQ_REQUEST_FEC_KR		0x04
+#define I40E_AQ_REQUEST_FEC_RS		0x08
+#define I40E_AQ_ENABLE_FEC_AUTO		0x10
+#define I40E_AQ_FEC
+#define I40E_AQ_MODULE_TYPE_EXT_MASK	0xE0
+#define I40E_AQ_MODULE_TYPE_EXT_SHIFT	5
+
 	u8	ext_comp_code;
 	u8	phy_id[4];
 	u8	module_type[3];
@@ -1726,7 +1737,15 @@ struct i40e_aq_set_phy_config { /* same bits as above in all */
 #define I40E_AQ_PHY_TYPE_EXT_25G_CR	0X02
 #define I40E_AQ_PHY_TYPE_EXT_25G_SR	0x04
 #define I40E_AQ_PHY_TYPE_EXT_25G_LR	0x08
-	u8	reserved[2];
+	u8	fec_config;
+#define I40E_AQ_SET_FEC_ABILITY_KR	BIT(0)
+#define I40E_AQ_SET_FEC_ABILITY_RS	BIT(1)
+#define I40E_AQ_SET_FEC_REQUEST_KR	BIT(2)
+#define I40E_AQ_SET_FEC_REQUEST_RS	BIT(3)
+#define I40E_AQ_SET_FEC_AUTO		BIT(4)
+#define I40E_AQ_PHY_FEC_CONFIG_SHIFT	0x0
+#define I40E_AQ_PHY_FEC_CONFIG_MASK	(0x1F << I40E_AQ_PHY_FEC_CONFIG_SHIFT)
+	u8	reserved;
 };
 
 I40E_CHECK_CMD_LENGTH(i40e_aq_set_phy_config);
@@ -1816,6 +1835,8 @@ struct i40e_aqc_get_link_status {
 	u8	loopback; /* use defines from i40e_aqc_set_lb_mode */
 	__le16	max_frame_size;
 	u8	config;
+#define I40E_AQ_CONFIG_FEC_KR_ENA	0x01
+#define I40E_AQ_CONFIG_FEC_RS_ENA	0x02
 #define I40E_AQ_CONFIG_CRC_ENA		0x04
 #define I40E_AQ_CONFIG_PACING_MASK	0x78
 	u8	external_power_ability;
Signature · 1 line
2.4.11
#4 lore raw

PATCH 3/5 i40e: Add FEC for 25g

Quoted 17 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On Behalf Of Bimmy Pujari
Sent: Monday, November 14, 2016 1:07 PM
To: intel-wired-lan at lists.osuosl.org
Cc: Naczyk, Jacek <[email protected]>
Subject: [Intel-wired-lan] [next PATCH S53-V2 3/5] i40e: Add FEC for 25g

From: Carolyn Wyborny <[email protected]>

This patch adds adminq support for Forward Error Correction ("FEC")for 25g products.

Change-ID Iaff4910737c239d2c730e5c22a313ce9c37d3964
Quoted 7 lines
---
 drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h  | 25
++++++++++++++++++++--
 drivers/net/ethernet/intel/i40e/i40e_common.c      |  2 ++
 .../net/ethernet/intel/i40evf/i40e_adminq_cmd.h    | 25
++++++++++++++++++++--
 3 files changed, 48 insertions(+), 4 deletions(-)
#5 lore raw

PATCH 3/5 i40e: Add FEC for 25g

In reply to Bimmy Pujari
Quoted 17 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On Behalf Of Bimmy Pujari
Sent: Monday, November 14, 2016 1:07 PM
To: intel-wired-lan at lists.osuosl.org
Cc: Naczyk, Jacek <[email protected]>
Subject: [Intel-wired-lan] [next PATCH S53-V2 3/5] i40e: Add FEC for 25g

From: Carolyn Wyborny <[email protected]>

This patch adds adminq support for Forward Error Correction ("FEC")for 25g products.

Change-ID Iaff4910737c239d2c730e5c22a313ce9c37d3964
Quoted 7 lines
---
 drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h  | 25
++++++++++++++++++++--
 drivers/net/ethernet/intel/i40e/i40e_common.c      |  2 ++
 .../net/ethernet/intel/i40evf/i40e_adminq_cmd.h    | 25
++++++++++++++++++++--
 3 files changed, 48 insertions(+), 4 deletions(-)
#6 lore raw

PATCH 4/5 i40e: Add functions which apply correct PHY access method for read and write operation

In reply to Bimmy Pujari

From: Michal Kosiarz <[email protected]>

Depending on external PHY type, register access method should be different. Clause22 or Clause45 can be chosen for different PHYs. Implemented functions apply correct access method for used device.

Change-ID If39d5f0da9c0b905a8cbdc1ab89885535e7d0426
---
 drivers/net/ethernet/intel/i40e/i40e_common.c      | 72 ++++++++++++++++++++++
 drivers/net/ethernet/intel/i40e/i40e_prototype.h   |  4 ++
 drivers/net/ethernet/intel/i40evf/i40e_prototype.h |  4 ++
 3 files changed, 80 insertions(+)
drivers/net/ethernet/intel/i40e/i40e_common.c +72 -0
index d9da786..59e766c 100644
@@ -4676,6 +4676,78 @@ i40e_status i40e_write_phy_register_clause45(struct i40e_hw *hw, u8 page,
 }
 
 /**
+ * i40e_write_phy_register
+ * @hw: pointer to the HW structure
+ * @page: registers page number
+ * @reg: register address in the page
+ * @phy_adr: PHY address on MDIO interface
+ * @value: PHY register value
+ *
+ * Writes value to specified PHY register
+ **/
+i40e_status i40e_write_phy_register(struct i40e_hw *hw,
+				u8 page, u16 reg, u8 phy_addr, u16 value)
+{
+	i40e_status status;
+
+	switch (hw->device_id) {
+	case I40E_DEV_ID_1G_BASE_T_X722:
+		status = i40e_write_phy_register_clause22(hw,
+			reg, phy_addr, value);
+		break;
+	case I40E_DEV_ID_10G_BASE_T:
+	case I40E_DEV_ID_10G_BASE_T4:
+	case I40E_DEV_ID_10G_BASE_T_X722:
+	case I40E_DEV_ID_25G_B:
+	case I40E_DEV_ID_25G_SFP28:
+		status = i40e_write_phy_register_clause45(hw,
+			page, reg, phy_addr, value);
+		break;
+	default:
+		status = I40E_ERR_UNKNOWN_PHY;
+		break;
+	}
+
+	return status;
+}
+
+/**
+ * i40e_read_phy_register
+ * @hw: pointer to the HW structure
+ * @page: registers page number
+ * @reg: register address in the page
+ * @phy_adr: PHY address on MDIO interface
+ * @value: PHY register value
+ *
+ * Reads specified PHY register value
+ **/
+i40e_status i40e_read_phy_register(struct i40e_hw *hw,
+				u8 page, u16 reg, u8 phy_addr, u16 *value)
+{
+	i40e_status status;
+
+	switch (hw->device_id) {
+	case I40E_DEV_ID_1G_BASE_T_X722:
+		status = i40e_read_phy_register_clause22(hw, reg, phy_addr,
+							 value);
+		break;
+	case I40E_DEV_ID_10G_BASE_T:
+	case I40E_DEV_ID_10G_BASE_T4:
+	case I40E_DEV_ID_10G_BASE_T_X722:
+	case I40E_DEV_ID_25G_B:
+	case I40E_DEV_ID_25G_SFP28:
+		status = i40e_read_phy_register_clause45(hw, page, reg,
+							 phy_addr, value);
+		break;
+	default:
+		status = I40E_ERR_UNKNOWN_PHY;
+		break;
+	}
+
+	return status;
+}
+
+/**
  * i40e_get_phy_address
  * @hw: pointer to the HW structure
  * @dev_num: PHY port num that address we want
drivers/net/ethernet/intel/i40e/i40e_prototype.h +4 -0
index 4e641a6..bb5c982 100644
@@ -373,6 +373,10 @@ i40e_status i40e_read_phy_register_clause45(struct i40e_hw *hw,
 				u8 page, u16 reg, u8 phy_addr, u16 *value);
 i40e_status i40e_write_phy_register_clause45(struct i40e_hw *hw,
 				u8 page, u16 reg, u8 phy_addr, u16 value);
+i40e_status i40e_read_phy_register(struct i40e_hw *hw,
+				u8 page, u16 reg, u8 phy_addr, u16 *value);
+i40e_status i40e_write_phy_register(struct i40e_hw *hw,
+				u8 page, u16 reg, u8 phy_addr, u16 value);
 u8 i40e_get_phy_address(struct i40e_hw *hw, u8 dev_num);
 i40e_status i40e_blink_phy_link_led(struct i40e_hw *hw,
 				    u32 time, u32 interval);
drivers/net/ethernet/intel/i40evf/i40e_prototype.h +4 -0
index d89d521..ee5d7fe 100644
@@ -115,6 +115,10 @@ i40e_status i40e_read_phy_register(struct i40e_hw *hw, u8 page,
 				   u16 reg, u8 phy_addr, u16 *value);
 i40e_status i40e_write_phy_register(struct i40e_hw *hw, u8 page,
 				    u16 reg, u8 phy_addr, u16 value);
+i40e_status i40e_read_phy_register(struct i40e_hw *hw,
+				u8 page, u16 reg, u8 phy_addr, u16 *value);
+i40e_status i40e_write_phy_register(struct i40e_hw *hw,
+				u8 page, u16 reg, u8 phy_addr, u16 value);
 u8 i40e_get_phy_address(struct i40e_hw *hw, u8 dev_num);
 i40e_status i40e_blink_phy_link_led(struct i40e_hw *hw,
 				    u32 time, u32 interval);
Signature · 1 line
2.4.11
#7 lore raw

PATCH 4/5 i40e: Add functions which apply correct PHY access method for read and write operation

Quoted 15 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On Behalf Of Bimmy Pujari
Sent: Monday, November 14, 2016 1:07 PM
To: intel-wired-lan at lists.osuosl.org
Cc: Kosiarz, Michal <[email protected]>
Subject: [Intel-wired-lan] [next PATCH S53-V2 4/5] i40e: Add functions which apply correct PHY access method for read and write operation

From: Michal Kosiarz <[email protected]>

Depending on external PHY type, register access method should be different. Clause22 or Clause45 can be chosen for different PHYs. Implemented functions apply correct access method for used device.

Quoted 8 lines
Change-ID If39d5f0da9c0b905a8cbdc1ab89885535e7d0426
---
 drivers/net/ethernet/intel/i40e/i40e_common.c      | 72
++++++++++++++++++++++
 drivers/net/ethernet/intel/i40e/i40e_prototype.h   |  4 ++
 drivers/net/ethernet/intel/i40evf/i40e_prototype.h |  4 ++
 3 files changed, 80 insertions(+)
#8 lore raw

PATCH 5/5 i40e: lock service task correctly

In reply to Bimmy Pujari

From: Mitch Williams <[email protected]>

The service task lock was being set in the scheduling function, not the actual service task. This would potentially leave the bit set for a long time before the task actually ran. Furthermore, if the service task takes too long, it calls the schedule function to reschedule itself - which would fail to take the lock and do nothing.

Instead, set and clear the lock bit in the service task itself. In the process, get rid of the i40e_service_event_complete() function, which is really just two lines of code that can be put right in the service task itself.

Change-ID I83155e682b686121e2897f4429eb7d3f7c669168

---
Testing Hints : Should be no functional change, particularly around link up/down events. This is prep work for using this lock bit in the client.

 drivers/net/ethernet/intel/i40e/i40e_main.c | 24 +++++++-----------------
 1 file changed, 7 insertions(+), 17 deletions(-)
drivers/net/ethernet/intel/i40e/i40e_main.c +7 -17
index 849feaa..57850fd 100644
@@ -288,8 +288,7 @@ struct i40e_vsi *i40e_find_vsi_from_id(struct i40e_pf *pf, u16 id)
 void i40e_service_event_schedule(struct i40e_pf *pf)
 {
 	if (!test_bit(__I40E_DOWN, &pf->state) &&
-	    !test_bit(__I40E_RESET_RECOVERY_PENDING, &pf->state) &&
-	    !test_and_set_bit(__I40E_SERVICE_SCHED, &pf->state))
+	    !test_bit(__I40E_RESET_RECOVERY_PENDING, &pf->state))
 		queue_work(i40e_wq, &pf->service_task);
 }
 
@@ -5943,19 +5942,6 @@ static void i40e_handle_lan_overflow_event(struct i40e_pf *pf,
 }
 
 /**
- * i40e_service_event_complete - Finish up the service event
- * @pf: board private structure
- **/
-static void i40e_service_event_complete(struct i40e_pf *pf)
-{
-	WARN_ON(!test_bit(__I40E_SERVICE_SCHED, &pf->state));
-
-	/* flush memory to make sure state is correct before next watchog */
-	smp_mb__before_atomic();
-	clear_bit(__I40E_SERVICE_SCHED, &pf->state);
-}
-
-/**
  * i40e_get_cur_guaranteed_fd_count - Get the consumed guaranteed FD filters
  * @pf: board private structure
  **/
@@ -7264,10 +7250,12 @@ static void i40e_service_task(struct work_struct *work)
 
 	/* don't bother with service tasks if a reset is in progress */
 	if (test_bit(__I40E_RESET_RECOVERY_PENDING, &pf->state)) {
-		i40e_service_event_complete(pf);
 		return;
 	}
 
+	if (test_and_set_bit(__I40E_SERVICE_SCHED, &pf->state))
+		return;
+
 	i40e_detect_recover_hung(pf);
 	i40e_sync_filters_subtask(pf);
 	i40e_reset_subtask(pf);
@@ -7280,7 +7268,9 @@ static void i40e_service_task(struct work_struct *work)
 	i40e_sync_udp_filters_subtask(pf);
 	i40e_clean_adminq_subtask(pf);
 
-	i40e_service_event_complete(pf);
+	/* flush memory to make sure state is correct before next watchdog */
+	smp_mb__before_atomic();
+	clear_bit(__I40E_SERVICE_SCHED, &pf->state);
 
 	/* If the tasks have taken longer than one timer cycle or there
 	 * is more work to be done, reschedule the service task now
Signature · 1 line
2.4.11
#9 lore raw

PATCH 5/5 i40e: lock service task correctly

Quoted 20 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On Behalf Of Bimmy Pujari
Sent: Monday, November 14, 2016 1:07 PM
To: intel-wired-lan at lists.osuosl.org
Subject: [Intel-wired-lan] [next PATCH S53-V2 5/5] i40e: lock service task correctly

From: Mitch Williams <[email protected]>

The service task lock was being set in the scheduling function, not the actual service task. This would potentially leave the bit set for a long time before the task actually ran. Furthermore, if the service task takes too long, it calls the schedule function to reschedule itself - which would fail to take the lock and do nothing.

Instead, set and clear the lock bit in the service task itself. In the process, get rid of the i40e_service_event_complete() function, which is really just two lines of code that can be put right in the service task itself.

Quoted 8 lines
Change-ID I83155e682b686121e2897f4429eb7d3f7c669168

---
Testing Hints : Should be no functional change, particularly around link up/down events. This is prep work for using this lock bit in the client.

 drivers/net/ethernet/intel/i40e/i40e_main.c | 24 +++++++-----------------
 1 file changed, 7 insertions(+), 17 deletions(-)
#10 lore raw

PATCH 1/5 i40e: use unsigned printf format specifier for active_filters count

In reply to Bimmy Pujari
Quoted 18 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On Behalf Of Bimmy Pujari
Sent: Monday, November 14, 2016 1:07 PM
To: intel-wired-lan at lists.osuosl.org
Subject: [Intel-wired-lan] [next PATCH S53-V2 1/5] i40e: use unsigned printf format specifier for active_filters count

From: Jacob Keller <[email protected]>

Replace the %d specifier used for printing vsi->active_filters and vsi->promisc_threshold with an unsigned %u format specifier. While it is unlikely in practice that these values will ever reach such a large number they are unsigned values and thus should not be interpreted as negative numbers.

Change-ID Iff050fad5a1c8537c4c57fcd527441cd95cfc0d4
Quoted 7 lines

---
Testing-hints:
This should go upstream, even though it is in debugfs code. We're not adding features but simply correcting output of existing features.

 drivers/net/ethernet/intel/i40e/i40e_debugfs.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)