drm/i915/lspcon: Enable AUX interrupts for resume time initialization
Subsystems (2)
PATCH 1/1 drm/i915/lspcon: Enable AUX interrupts for resume time initialization
For LSPCON initialization during system resume we need AUX functionality, but we call the corresponding encoder reset hook with all interrupts disabled. Without interrupts we'll do a poll-wait for AUX transfer completions, which adds a significant delay if the transfers timeout/need to be retried for some reason.
Fix this by enabling interrupts before calling the reset hooks. Note that while this will enable AUX interrupts it will keep HPD interrupts disabled, in a similar way to the init time output setup code.
This issue existed since LSPCON support was added.
--- drivers/gpu/drm/i915/i915_drv.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/i915_drv.c +4 -1
@@ -1580,18 +1580,21 @@ static int i915_drm_resume(struct drm_device *dev)intel_opregion_setup (dev_priv);intel_init_pch_refclk (dev); -drm_mode_config_reset (dev);/* * Interrupts have to be enabled before any batches are run. If not the * GPU will hang. i915_gem_init_hw() will initiate batches to * update/restore the context. * +* drm_mode_config_reset() needs AUX interrupts. +* * Modeset enabling in intel_modeset_init_hw() also needs working * interrupts. */ intel_runtime_pm_enable_interrupts (dev_priv); +drm_mode_config_reset (dev); +mutex_lock (&dev->struct_mutex);if (i915_gem_init_hw (dev)) {DRM_ERROR ("failed to re-initialize GPU, declaring wedged!\n" );
Signature · 6 lines
2.5.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v2 1/1 drm/i915/lspcon: Enable AUX interrupts for resume time initialization
For LSPCON initialization during system resume we need AUX functionality, but we call the corresponding encoder reset hook with all interrupts disabled. Without interrupts we'll do a poll-wait for AUX transfer completions, which adds a significant delay if the transfers timeout/need to be retried for some reason.
Fix this by enabling interrupts before calling the reset hooks. Note that while this will enable AUX interrupts it will keep HPD interrupts disabled, in a similar way to the init time output setup code.
This issue existed since LSPCON support was added.
v2:
- Rebased on drm-tip.
--- drivers/gpu/drm/i915/i915_drv.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/i915_drv.c +4 -1
@@ -1582,18 +1582,21 @@ static int i915_drm_resume(struct drm_device *dev)intel_opregion_setup (dev_priv);intel_init_pch_refclk (dev_priv); -drm_mode_config_reset (dev);/* * Interrupts have to be enabled before any batches are run. If not the * GPU will hang. i915_gem_init_hw() will initiate batches to * update/restore the context. * +* drm_mode_config_reset() needs AUX interrupts. +* * Modeset enabling in intel_modeset_init_hw() also needs working * interrupts. */ intel_runtime_pm_enable_interrupts (dev_priv); +drm_mode_config_reset (dev); +mutex_lock (&dev->struct_mutex);if (i915_gem_init_hw (dev)) {DRM_ERROR ("failed to re-initialize GPU, declaring wedged!\n" );
Signature · 6 lines
2.5.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 35 lines · Imre Deak
For LSPCON initialization during system resume we need AUX functionality, but we call the corresponding encoder reset hook with all interrupts disabled. Without interrupts we'll do a poll-wait for AUX transfer completions, which adds a significant delay if the transfers timeout/need to be retried for some reason.
Fix this by enabling interrupts before calling the reset hooks. Note that while this will enable AUX interrupts it will keep HPD interrupts disabled, in a similar way to the init time output setup code.
This issue existed since LSPCON support was added.
v2:
- Rebased on drm-tip.Cc Shashank Sharma <[email protected]>Signed-off-by Imre Deak <[email protected]>--- drivers/gpu/drm/i915/i915_drv.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/i915_drv.c +0
-1@@ -1582,18 +1582,21 @@ static int i915_drm_resume(struct drm_device *dev)intel_opregion_setup (dev_priv);intel_init_pch_refclk (dev_priv); -drm_mode_config_reset (dev);/* * Interrupts have to be enabled before any batches are run. If not the * GPU will hang. i915_gem_init_hw() will initiate batches to * update/restore the context.
drivers/gpu/drm/i915/i915_drv.c static int i915_drm_resume(struct drm_device *dev) · line 1599
Quoted 10 lines
drivers/gpu/drm/i915/i915_drv.c +4
-0* +* drm_mode_config_reset() needs AUX interrupts. +* * Modeset enabling in intel_modeset_init_hw() also needs working * interrupts. */ intel_runtime_pm_enable_interrupts (dev_priv); +drm_mode_config_reset (dev); +
Didn't look like anything should seriously explode.
There is a slight concern on g4x/vlv/chv that an AUX interrupts would trigger the hpd irq handler, which doesn't realize it's supposed to ignore the actual hpd bits in PORT_HOTPLUG_STAT. So any aux before we enable hpd processing for real could do something bad. So I guess we should add some kind of software tracking for that stuff like we have for PIPESTAT.
Quoted 10 lines
drivers/gpu/drm/i915/i915_drv.c +0
-0mutex_lock (&dev->struct_mutex);if (i915_gem_init_hw (dev)) {DRM_ERROR ("failed to re-initialize GPU, declaring wedged!\n" );Signature · 6 lines
2.5.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 49 lines · Ville Syrjälä
Quoted 43 lines · Imre Deak
For LSPCON initialization during system resume we need AUX functionality, but we call the corresponding encoder reset hook with all interrupts disabled. Without interrupts we'll do a poll-wait for AUX transfer completions, which adds a significant delay if the transfers timeout/need to be retried for some reason.
Fix this by enabling interrupts before calling the reset hooks. Note that while this will enable AUX interrupts it will keep HPD interrupts disabled, in a similar way to the init time output setup code.
This issue existed since LSPCON support was added.
v2:
- Rebased on drm-tip.Cc Shashank Sharma <[email protected]>Signed-off-by Imre Deak <[email protected]>---
drivers/gpu/drm/i915/i915_drv.c | 5 ++++-1 file changed, 4 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/i915_drv.c +0
-0@@ -1582,18 +1582,21 @@ static int i915_drm_resume(struct drm_device *dev) intel_opregion_setup(dev_priv);
intel_init_pch_refclk(dev_priv);drivers/gpu/drm/i915/i915_drv.c +0
-1-drm_mode_config_reset (dev);
/*
* Interrupts have to be enabled before any batches are run. If not the
* GPU will hang.i915_gem_init_hw()will initiate batches to
* update/restore the context.
*drivers/gpu/drm/i915/i915_drv.c +2
-0+ * drm_mode_config_reset() needs AUX interrupts. + ** Modeset enabling in
intel_modeset_init_hw()also needs working
* interrupts.
*/
intel_runtime_pm_enable_interrupts(dev_priv);drivers/gpu/drm/i915/i915_drv.c static int i915_drm_resume(struct drm_device *dev) · line 1599
Quoted 2 lines
drivers/gpu/drm/i915/i915_drv.c +2
-0+drm_mode_config_reset (dev); +Didn't look like anything should seriously explode.
Quoted 8 lines
Reviewed-by Ville Syrjälä <[email protected]>There is a slight concern on g4x/vlv/chv that an AUX interrupts would trigger the hpd irq handler, which doesn't realize it's supposed to ignore the actual hpd bits in
PORT_HOTPLUG_STAT. So any aux before we enable hpd processing for real could do something bad. So I guess we should add some kind of software tracking for that stuff like we have for PIPESTAT.
Didn't think about that, but BSpec tells me those are masked by the HPD IRQ enable bits in PORT_HOTPLUG_EN and those we enable only later. Otherwise this would be also a problem during output setup time.
--Imre
Quoted 7 lines
Quoted 7 lines
mutex_lock(&dev->struct_mutex);
if (i915_gem_init_hw(dev)) {
DRM_ERROR("failed to re-initialize GPU, declaring wedged!\n"); --
2.5.0
Quoted 5 lines
Quoted 4 lines
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 59 lines · Imre Deak
Quoted 49 lines · Ville Syrjälä
Quoted 43 lines · Imre Deak
For LSPCON initialization during system resume we need AUX functionality, but we call the corresponding encoder reset hook with all interrupts disabled. Without interrupts we'll do a poll-wait for AUX transfer completions, which adds a significant delay if the transfers timeout/need to be retried for some reason.
Fix this by enabling interrupts before calling the reset hooks. Note that while this will enable AUX interrupts it will keep HPD interrupts disabled, in a similar way to the init time output setup code.
This issue existed since LSPCON support was added.
v2:
- Rebased on drm-tip.Cc Shashank Sharma <[email protected]>Signed-off-by Imre Deak <[email protected]>---
drivers/gpu/drm/i915/i915_drv.c | 5 ++++-1 file changed, 4 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/i915_drv.c +0
-0@@ -1582,18 +1582,21 @@ static int i915_drm_resume(struct drm_device *dev) intel_opregion_setup(dev_priv);
intel_init_pch_refclk(dev_priv);drivers/gpu/drm/i915/i915_drv.c +0
-1-drm_mode_config_reset (dev);
/*
* Interrupts have to be enabled before any batches are run. If not the
* GPU will hang.i915_gem_init_hw()will initiate batches to
* update/restore the context.
*drivers/gpu/drm/i915/i915_drv.c +2
-0+ * drm_mode_config_reset() needs AUX interrupts. + ** Modeset enabling in
intel_modeset_init_hw()also needs working
* interrupts.
*/
intel_runtime_pm_enable_interrupts(dev_priv);drivers/gpu/drm/i915/i915_drv.c static int i915_drm_resume(struct drm_device *dev) · line 1599
Quoted 2 lines
drivers/gpu/drm/i915/i915_drv.c +2
-0+drm_mode_config_reset (dev); +Didn't look like anything should seriously explode.
Quoted 8 lines
Reviewed-by Ville Syrjälä <[email protected]>There is a slight concern on g4x/vlv/chv that an AUX interrupts would trigger the hpd irq handler, which doesn't realize it's supposed to ignore the actual hpd bits in
PORT_HOTPLUG_STAT. So any aux before we enable hpd processing for real could do something bad. So I guess we should add some kind of software tracking for that stuff like we have for PIPESTAT.
Quoted 3 lines
Didn't think about that, but BSpec tells me those are masked by the HPD IRQ enable bits in PORT_HOTPLUG_EN and those we enable only later. Otherwise this would be also a problem during output setup time.
Hmm. Are they really masked? I though it's just an IER effectively.
Quoted 15 lines
--Imre
Quoted 12 lines
Quoted 11 lines
mutex_lock(&dev->struct_mutex);
if (i915_gem_init_hw(dev)) {
DRM_ERROR("failed to re-initialize GPU, declaring wedged!\n"); --
2.5.0_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 75 lines · Ville Syrjälä
Quoted 74 lines · Imre Deak
Quoted 72 lines · Ville Syrjälä
Quoted 53 lines · Imre Deak
For LSPCON initialization during system resume we need AUX functionality, but we call the corresponding encoder reset hook with all
interrupts disabled. Without interrupts we'll do a poll-wait for AUX
transfer completions, which adds a significant delay if the transfers
timeout/need to be retried for some reason.Fix this by enabling interrupts before calling the reset hooks. Note
that while this will enable AUX interrupts it will keep HPD interrupts
disabled, in a similar way to the init time output setup code.This issue existed since LSPCON support was added.
v2:
- Rebased on drm-tip.Cc Shashank Sharma <[email protected]>Signed-off-by Imre Deak <[email protected]>---
drivers/gpu/drm/i915/i915_drv.c | 5 ++++-1 file changed, 4 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/i915_drv.c +0
-0@@ -1582,18 +1582,21 @@ static int i915_drm_resume(struct drm_device *dev) intel_opregion_setup(dev_priv);
intel_init_pch_refclk(dev_priv);drivers/gpu/drm/i915/i915_drv.c +0
-1-drm_mode_config_reset (dev);
/*
* Interrupts have to be enabled before any batches are run. If not the
* GPU will hang.i915_gem_init_hw()will initiate batches to
* update/restore the context.
*drivers/gpu/drm/i915/i915_drv.c +2
-0+ * drm_mode_config_reset() needs AUX interrupts. + ** Modeset enabling in
intel_modeset_init_hw()also needs working
* interrupts.
*/intel_runtime_pm_enable_interrupts(dev_priv);drivers/gpu/drm/i915/i915_drv.c static int i915_drm_resume(struct drm_device *dev) · line 1599
Quoted 2 lines
drivers/gpu/drm/i915/i915_drv.c +2
-0+drm_mode_config_reset (dev); +Didn't look like anything should seriously explode.
Reviewed-by Ville Syrjälä <[email protected]>There is a slight concern on g4x/vlv/chv that an AUX interrupts would
trigger the hpd irq handler, which doesn't realize it's supposed to
ignore the actual hpd bits inPORT_HOTPLUG_STAT. So any aux before we
enable hpd processing for real could do something bad. So I guess we
should add some kind of software tracking for that stuff like we have
for PIPESTAT.
Quoted 6 lines
Quoted 4 lines
Didn't think about that, but BSpec tells me those are masked by the HPD
IRQ enable bits in PORT_HOTPLUG_EN and those we enable only later. Otherwise this would be also a problem during output setup time.Hmm. Are they really masked? I though it's just an IER effectively.
I only tried for real on BXT/SKL where I had to enable the interrupts (in PCH_PORT_HOTPLUG) for HPD sensing. The CHV BSpec suggests the same for the live state bits, but yes it's not clear if the long/short detect bits are completely masked by the enable flags or they are just not propagated if not enabled. Will give it a try tomorrow.
Quoted 12 lines
Quoted 12 lines
--Imre
Quoted 8 lines
Quoted 8 lines
mutex_lock(&dev->struct_mutex);
if (i915_gem_init_hw(dev)) {DRM_ERROR("failed to re-initialize GPU, declaring wedged!\n");
--
2.5.0
Quoted 6 lines
Quoted 5 lines
Quoted 5 lines
Quoted 4 lines
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 81 lines · Imre Deak
Quoted 80 lines · Ville Syrjälä
Quoted 78 lines · Imre Deak
Quoted 61 lines · Ville Syrjälä
Quoted 53 lines · Imre Deak
For LSPCON initialization during system resume we need AUX functionality, but we call the corresponding encoder reset hook with all
interrupts disabled. Without interrupts we'll do a poll-wait for AUX
transfer completions, which adds a significant delay if the transfers
timeout/need to be retried for some reason.Fix this by enabling interrupts before calling the reset hooks. Note
that while this will enable AUX interrupts it will keep HPD interrupts
disabled, in a similar way to the init time output setup code.This issue existed since LSPCON support was added.
v2:
- Rebased on drm-tip.Cc Shashank Sharma <[email protected]>Signed-off-by Imre Deak <[email protected]>---
drivers/gpu/drm/i915/i915_drv.c | 5 ++++-1 file changed, 4 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/i915_drv.c +0
-0@@ -1582,18 +1582,21 @@ static int i915_drm_resume(struct drm_device *dev) intel_opregion_setup(dev_priv);
intel_init_pch_refclk(dev_priv);drivers/gpu/drm/i915/i915_drv.c +0
-1-drm_mode_config_reset (dev);
/*
* Interrupts have to be enabled before any batches are run. If not the
* GPU will hang.i915_gem_init_hw()will initiate batches to
* update/restore the context.
*drivers/gpu/drm/i915/i915_drv.c +2
-0+ * drm_mode_config_reset() needs AUX interrupts. + ** Modeset enabling in
intel_modeset_init_hw()also needs working
* interrupts.
*/intel_runtime_pm_enable_interrupts(dev_priv);drivers/gpu/drm/i915/i915_drv.c static int i915_drm_resume(struct drm_device *dev) · line 1599
Quoted 2 lines
drivers/gpu/drm/i915/i915_drv.c +2
-0+drm_mode_config_reset (dev); +Didn't look like anything should seriously explode.
Reviewed-by Ville Syrjälä <[email protected]>Quoted 11 lines
There is a slight concern on g4x/vlv/chv that an AUX interrupts would
trigger the hpd irq handler, which doesn't realize it's supposed to
ignore the actual hpd bits inPORT_HOTPLUG_STAT. So any aux before we
enable hpd processing for real could do something bad. So I guess we
should add some kind of software tracking for that stuff like we have
for PIPESTAT.Didn't think about that, but BSpec tells me those are masked by the HPD
IRQ enable bits in PORT_HOTPLUG_EN and those we enable only later. Otherwise this would be also a problem during output setup time.
Quoted 7 lines
Quoted 1 line
Hmm. Are they really masked? I though it's just an IER effectively.
I only tried for real on BXT/SKL where I had to enable the interrupts (in
PCH_PORT_HOTPLUG) for HPD sensing. The CHV BSpec suggests the same for the live state bits, but yes it's not clear if the long/short detect bits are completely masked by the enable flags or they are just not propagated if not enabled. Will give it a try tomorrow.
Hmm. Yeah, we did in fact chat about this. Already forgot. Spec seems to suggest you are correct. But checking on actual hw is always a good idea.
Quoted 19 lines
Quoted 19 lines
Quoted 18 lines
--Imre
Quoted 13 lines
Quoted 12 lines
mutex_lock(&dev->struct_mutex);
if (i915_gem_init_hw(dev)) {DRM_ERROR("failed to re-initialize GPU, declaring wedged!\n");
--
2.5.0_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 26 lines · Ville Syrjälä
[...]
Quoted 17 lines
Quoted 17 lines
Quoted 16 lines
Quoted 11 lines
There is a slight concern on g4x/vlv/chv that an AUX interrupts would
trigger the hpd irq handler, which doesn't realize it's supposed to
ignore the actual hpd bits inPORT_HOTPLUG_STAT. So any aux before we
enable hpd processing for real could do something bad. So I guess we
should add some kind of software tracking for that stuff like we have
for PIPESTAT.Didn't think about that, but BSpec tells me those are masked by the HPD
IRQ enable bits in PORT_HOTPLUG_EN and those we enable only later. Otherwise this would be also a problem during output setup time.Quoted 7 lines
Quoted 1 line
Hmm. Are they really masked? I though it's just an IER effectively.
I only tried for real on BXT/SKL where I had to enable the interrupts (in
PCH_PORT_HOTPLUG) for HPD sensing. The CHV BSpec suggests the same for the live state bits, but yes it's not clear if the long/short detect bits are completely masked by the enable flags or they are just not propagated if not enabled. Will give it a try tomorrow.
Quoted 3 lines
Hmm. Yeah, we did in fact chat about this. Already forgot. Spec seems to suggest you are correct. But checking on actual hw is always a good idea.
Checked now both on BXT and VLV both the live state and short/long detect bits in the hotplug_stat reg are masked by the hotplug_en bits. (And we clear any stale short/long bits during IRQ reset.)
--Imre
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 10 lines · Imre Deak
For LSPCON initialization during system resume we need AUX functionality, but we call the corresponding encoder reset hook with all interrupts disabled. Without interrupts we'll do a poll-wait for AUX transfer completions, which adds a significant delay if the transfers timeout/need to be retried for some reason.
Fix this by enabling interrupts before calling the reset hooks. Note that while this will enable AUX interrupts it will keep HPD interrupts disabled, in a similar way to the init time output setup code.
Quoted 7 lines
This issue existed since LSPCON support was added.
v2:
- Rebased on drm-tip.Cc Shashank Sharma <[email protected]>Signed-off-by Imre Deak <[email protected]>
Quoted 38 lines
--- drivers/gpu/drm/i915/i915_drv.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/i915_drv.c +4
-1@@ -1582,18 +1582,21 @@ static int i915_drm_resume(struct drm_device *dev)intel_opregion_setup (dev_priv);intel_init_pch_refclk (dev_priv); -drm_mode_config_reset (dev);/* * Interrupts have to be enabled before any batches are run. If not the * GPU will hang. i915_gem_init_hw() will initiate batches to * update/restore the context. * +* drm_mode_config_reset() needs AUX interrupts. +* * Modeset enabling in intel_modeset_init_hw() also needs working * interrupts. */ intel_runtime_pm_enable_interrupts (dev_priv); +drm_mode_config_reset (dev); +mutex_lock (&dev->struct_mutex);if (i915_gem_init_hw (dev)) {DRM_ERROR ("failed to re-initialize GPU, declaring wedged!\n" );Signature · 6 lines
2.5.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.BAT: success for drm/i915/lspcon: Enable AUX interrupts for resume time initialization (rev2)
In reply to Imre Deak== Series Details ==
== Series Details ==
Series: drm/i915/lspcon: Enable AUX interrupts for resume time initialization (rev2)
URL : https://patchwork.freedesktop.org/series/16106/
State : success
== Summary ==
Series 16106v2 drm/i915/lspcon: Enable AUX interrupts for resume time initialization
https://patchwork.freedesktop.org/api/1.0/series/16106/revisions/2/mbox/
fi-bdw-5557u total:245 pass:230 dwarn:0 dfail:0 fail:0 skip:15 fi-bsw-n3050 total:245 pass:205 dwarn:0 dfail:0 fail:0 skip:40 fi-byt-j1900 total:245 pass:217 dwarn:0 dfail:0 fail:0 skip:28 fi-byt-n2820 total:245 pass:213 dwarn:0 dfail:0 fail:0 skip:32 fi-hsw-4770 total:245 pass:225 dwarn:0 dfail:0 fail:0 skip:20 fi-hsw-4770r total:245 pass:225 dwarn:0 dfail:0 fail:0 skip:20 fi-ilk-650 total:245 pass:192 dwarn:0 dfail:0 fail:0 skip:53 fi-ivb-3520m total:245 pass:223 dwarn:0 dfail:0 fail:0 skip:22 fi-ivb-3770 total:245 pass:223 dwarn:0 dfail:0 fail:0 skip:22 fi-kbl-7500u total:245 pass:223 dwarn:0 dfail:0 fail:0 skip:22 fi-skl-6260u total:245 pass:231 dwarn:0 dfail:0 fail:0 skip:14 fi-skl-6700hq total:245 pass:224 dwarn:0 dfail:0 fail:0 skip:21 fi-skl-6700k total:245 pass:223 dwarn:1 dfail:0 fail:0 skip:21 fi-skl-6770hq total:245 pass:231 dwarn:0 dfail:0 fail:0 skip:14 fi-snb-2520m total:245 pass:213 dwarn:0 dfail:0 fail:0 skip:32 fi-snb-2600 total:245 pass:212 dwarn:0 dfail:0 fail:0 skip:33
41799fbb771e82427273492bfad8f2e2ae3027ef drm-tip: 2016y-11m-29d-20h-54m-07s UTC integration manifest d61aedb drm/i915/lspcon: Enable AUX interrupts for resume time initialization
== Logs ==
For more details see: https://intel-gfx-ci.01.org/CI/Patchwork_3147/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: ✓ Fi.CI.BAT: success for drm/i915/lspcon: Enable AUX interrupts for resume time initialization (rev2)
Quoted 10 lines · Patchwork
== Series Details ==
Series: drm/i915/lspcon: Enable AUX interrupts for resume time initialization (rev2) URL : https://patchwork.freedesktop.org/series/16106/
State : success== Summary ==
Series 16106v2 drm/i915/lspcon: Enable AUX interrupts for resume time initialization
https://patchwork.freedesktop.org/api/1.0/series/16106/revisions/2/mbox/
I pushed the patch to -dinq, thanks for the testing and review.
--Imre
Quoted 19 lines
fi-bdw-5557u total:245 pass:230 dwarn:0 dfail:0 fail:0 skip:15 fi-bsw-n3050 total:245 pass:205 dwarn:0 dfail:0 fail:0 skip:40 fi-byt-j1900 total:245 pass:217 dwarn:0 dfail:0 fail:0 skip:28 fi-byt-n2820 total:245 pass:213 dwarn:0 dfail:0 fail:0 skip:32 fi-hsw-4770 total:245 pass:225 dwarn:0 dfail:0 fail:0 skip:20 fi-hsw-4770r total:245 pass:225 dwarn:0 dfail:0 fail:0 skip:20 fi-ilk-650 total:245 pass:192 dwarn:0 dfail:0 fail:0 skip:53 fi-ivb-3520m total:245 pass:223 dwarn:0 dfail:0 fail:0 skip:22 fi-ivb-3770 total:245 pass:223 dwarn:0 dfail:0 fail:0 skip:22 fi-kbl-7500u total:245 pass:223 dwarn:0 dfail:0 fail:0 skip:22 fi-skl-6260u total:245 pass:231 dwarn:0 dfail:0 fail:0 skip:14 fi-skl-6700hq total:245 pass:224 dwarn:0 dfail:0 fail:0 skip:21 fi-skl-6700k total:245 pass:223 dwarn:1 dfail:0 fail:0 skip:21 fi-skl-6770hq total:245 pass:231 dwarn:0 dfail:0 fail:0 skip:14 fi-snb-2520m total:245 pass:213 dwarn:0 dfail:0 fail:0 skip:32 fi-snb-2600 total:245 pass:212 dwarn:0 dfail:0 fail:0 skip:33
Quoted 6 lines
41799fbb771e82427273492bfad8f2e2ae3027efdrm-tip: 2016y-11m-29d-20h-54m-07s UTC integration manifest d61aedb drm/i915/lspcon: Enable AUX interrupts for resume time initialization== Logs ==
For more details see: https://intel-gfx-ci.01.org/CI/Patchwork_3147/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx