Skip to contentSkip to conversation

ASoC: Using mxs-saif with simple-card

DISCUSSION Jörg Krause 1 participant 1 message Jan 7, 2017

lore
Share & tools
lore
#0 lore raw

Hi,

I am trying to use the simple-card framework on a custom i.MX28 board. There are two SAIF modules (saif0 and saif1) instantiated on the cpu. A reference for the platform driver is mxs-sgtl5000. The two cpu dais saif0 and saif1 are connected to the audio codec sgtl5000. saif0 is used to playback and saif1 is used to capture.

Unfortunately, I do not have a sgtl5000 codec, but a pcm5102a, a wm8524 and wm8731 to play with.

For all those codec I copied the mxs-sgtl5000 driver, e.g. mxs- pcm5102a, mxs-wm8524, mxs-wm8731. I will refer to these drivers as mxs- <codec> later. The only difference was in setting the mclk. That's why I'm interested in using the simple-card driver for this platform.

With the help of Mans Rullgard I came up with these parts of the device tree node when using the wm8731 codec:

sound {
	compatible = "simple-audio-card";
	simple-audio-card,name = "hbm10-wm8731";
	simple-audio-card,widgets =
				"Headphone", "Headphone Jack",
				"Microphone", "Microphone Jack",
				"Line", "Line Jack";
	simple-audio-card,routing =
				"Headphone Jack", "RHPOUT",
				"Headphone Jack", "LHPOUT",
				"LLINEIN", "Line Jack",
				"MICIN", "Mic Bias",
				"Mic Bias", "Microphone Jack";

	simple-audio-card,dai-link@0 {
		format = "i2s";
		bitclock-master = <&dai0_master>;
		frame-master = <&dai0_master>;
		mclk-fs = <256>;

		dai0_master: cpu {
			sound-dai = <&saif0>;
		};

		codec {
			sound-dai = <&wm8731>;
			clocks = <&saif0>;
		};
	};

	simple-audio-card,dai-link@1 {
		format = "i2s";
		bitclock-master = <&dai1_master>;
		frame-master = <&dai1_master>;
		mclk-fs = <256>;

		dai1_master: cpu {
			sound-dai = <&saif1>;
		};

		codec {
			sound-dai = <&wm8731>;
		};
	};
};
&saif0 {
	#sound-dai-cells = <0>;
	pinctrl-names = "default";
	pinctrl-0 = <&saif0_pins_a>;
	assigned-clocks = <&clks 53>;
	assigned-clock-rates = <12288000>;
	status = "okay";
};
&saif1 {
	#sound-dai-cells = <0>;
	pinctrl-names = "default";
	pinctrl-0 = <&saif1_pins_a>;
	fsl,saif-master = <&saif0>;
	status = "okay";
};
&i2c0 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c0_pins_a>;
	status = "okay";

	wm8731: wm8731@1a {
		#sound-dai-cells = <0>;
		compatible = "wlf,wm8731";
		reg = <0x1a>;
	};
};

From my understanding of the simple-card framework this should connect saif0 (cpu dai) <-> wm8731 (codec) and saif1 (cpu dai) <-> wm8731 (codec) as it is done in the probe function of the mxs-<codec> driver, right?

However, this gives me a warning while bringing up the board:

sysfs: cannot create duplicate filename '/devices/soc0/sound/mxs-saif- wm8731-hifi'.

Note, that the simple-card framework works fine for mxs-saif if using only the dai0 link (playback) and leaving the dai1 link (capture).

Am I doing something wrong here?

Is it possible to map the two dai links using the current simple-card framework?

Is anyone using the simple-card framework on mxs-saif using both playback and capture?

Best regards,
Jörg Krause
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel