arm: socfpga: stratix10: Add SOCFPGA Stratix10 base address

new file mode 100755
index 0000000..411518d
@@ -0,0 +1,48 @@
+/*
+ * Copyright (C) 2016, Intel Corporation
+ *
+ * SPDX-License-Identifier:	GPL-2.0
+ */
+
+#ifndef _SOCFPGA_S10_BASE_HARDWARE_H_
+#define _SOCFPGA_S10_BASE_HARDWARE_H_
+
+#define SOCFPGA_SMMU_ADDRESS			0xfa000000
+#define SOCFPGA_EMAC0_ADDRESS			0xff800000
+#define SOCFPGA_EMAC1_ADDRESS			0xff802000
+#define SOCFPGA_EMAC2_ADDRESS			0xff804000
+#define SOCFPGA_SDMMC_ADDRESS			0xff808000
+#define SOCFPGA_USB0_ADDRESS			0xffb00000
+#define SOCFPGA_USB1_ADDRESS			0xffb40000
+#define SOCFPGA_NANDREGS_ADDRESS		0xffb80000
+#define SOCFPGA_NANDDATA_ADDRESS		0xffb90000
+#define SOCFPGA_UART0_ADDRESS			0xffc02000
+#define SOCFPGA_UART1_ADDRESS			0xffc02100
+#define SOCFPGA_I2C0_ADDRESS			0xffc02800
+#define SOCFPGA_I2C1_ADDRESS			0xffc02900
+#define SOCFPGA_I2C2_ADDRESS			0xffc02a00
+#define SOCFPGA_I2C3_ADDRESS			0xffc02b00
+#define SOCFPGA_I2C4_ADDRESS			0xffc02c00
+#define SOCFPGA_SPTIMER0_ADDRESS		0xffc03000
+#define SOCFPGA_SPTIMER1_ADDRESS		0xffc03100
+#define SOCFPGA_GPIO0_ADDRESS			0xffc03200
+#define SOCFPGA_GPIO1_ADDRESS			0xffc03300
+#define SOCFPGA_SYSTIMER0_ADDRESS		0xffd00000
+#define SOCFPGA_SYSTIMER0_ADDRESS		0xffd00100
+#define SOCFPGA_L4WD0_ADDRESS			0xffd00200
+#define SOCFPGA_L4WD0_ADDRESS			0xffd00300
+#define SOCFPGA_L4WD0_ADDRESS			0xffd00400
+#define SOCFPGA_L4WD0_ADDRESS			0xffd00500
+#define SOCFPGA_CLKMGR_ADDRESS			0xffd10000
+#define SOCFPGA_RSTMGR_ADDRESS			0xffd11000
+#define SOCFPGA_SYSMGR_ADDRESS			0xffd12000
+#define SOCFPGA_PINMUX_DEDICATED_IO_ADDRESS	0xffd13000
+#define SOCFPGA_DMANONSECURE_ADDRESS		0xffda0000
+#define SOCFPGA_DMASECURE_ADDRESS		0xffda1000
+#define SOCFPGA_SPIS0_ADDRESS			0xffda2000
+#define SOCFPGA_SPIS1_ADDRESS			0xffda3000
+#define SOCFPGA_SPIM0_ADDRESS			0xffda4000
+#define SOCFPGA_SPIM1_ADDRESS			0xffda5000
+#define SOCFPGA_OCRAM_ADDRESS			0xffe00000
+
+#endif /* _SOCFPGA_S10_BASE_HARDWARE_H_ */

index d074478..73e3a46 100644
@@ -155,6 +155,14 @@ enum fdt_compat_id {
 	COMPAT_INTEL_BAYTRAIL_FSP_MDP,	/* Intel FSP memory-down params */
 	COMPAT_INTEL_IVYBRIDGE_FSP,	/* Intel Ivy Bridge FSP */
 	COMPAT_SUNXI_NAND,		/* SUNXI NAND controller */
+	COMPAT_ALTERA_SOCFPGA_CLK,	/* SoCFPGA Clock initialization */
+	COMPAT_ALTERA_SOCFPGA_PINCTRL_SINGLE,	/* pinctrl-single */
+	COMPAT_ALTERA_SOCFPGA_H2F_BRG,          /* Arria10 hps2fpga bridge */
+	COMPAT_ALTERA_SOCFPGA_LWH2F_BRG,        /* Arria10 lwhps2fpga bridge */
+	COMPAT_ALTERA_SOCFPGA_F2H_BRG,          /* Arria10 fpga2hps bridge */
+	COMPAT_ALTERA_SOCFPGA_F2SDR0,           /* Arria10 fpga2SDRAM0 bridge */
+	COMPAT_ALTERA_SOCFPGA_F2SDR1,           /* Arria10 fpga2SDRAM1 bridge */
+	COMPAT_ALTERA_SOCFPGA_F2SDR2,           /* Arria10 fpga2SDRAM2 bridge */
 
 	COMPAT_COUNT,
 };

index 81f47ef..ebe4a9a 100644
@@ -66,6 +66,14 @@ static const char * const compat_names[COMPAT_COUNT] = {
 	COMPAT(INTEL_BAYTRAIL_FSP_MDP, "intel,baytrail-fsp-mdp"),
 	COMPAT(INTEL_IVYBRIDGE_FSP, "intel,ivybridge-fsp"),
 	COMPAT(COMPAT_SUNXI_NAND, "allwinner,sun4i-a10-nand"),
+	COMPAT(ALTERA_SOCFPGA_CLK, "altr,clk-mgr"),
+	COMPAT(ALTERA_SOCFPGA_PINCTRL_SINGLE, "pinctrl-single"),
+	COMPAT(ALTERA_SOCFPGA_H2F_BRG, "altr,socfpga-hps2fpga-bridge"),
+	COMPAT(ALTERA_SOCFPGA_LWH2F_BRG, "altr,socfpga-lwhps2fpga-bridge"),
+	COMPAT(ALTERA_SOCFPGA_F2H_BRG, "altr,socfpga-fpga2hps-bridge"),
+	COMPAT(ALTERA_SOCFPGA_F2SDR0, "altr,socfpga-fpga2sdram0-bridge"),
+	COMPAT(ALTERA_SOCFPGA_F2SDR1, "altr,socfpga-fpga2sdram1-bridge"),
+	COMPAT(ALTERA_SOCFPGA_F2SDR2, "altr,socfpga-fpga2sdram2-bridge"),
 };
 
 const char *fdtdec_get_compatible(enum fdt_compat_id id)

index 902c321..2d66580 100644
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2014 Altera Corporation <www.altera.com>
+ * Copyright (C) 2014-2016 Altera Corporation <www.altera.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

@@ -36,10 +36,13 @@
 #define SOCFPGA_ECC_OCRAM_ADDRESS		0xff8c3000
 #define SOCFPGA_UART0_ADDRESS			0xffc02000
 #define SOCFPGA_OSC1TIMER0_ADDRESS		0xffd00000
+#define SOCFPGA_OSC1TIMER1_ADDRESS		0xffd00100
 #define SOCFPGA_CLKMGR_ADDRESS			0xffd04000
 #define SOCFPGA_RSTMGR_ADDRESS			0xffd05000
 
 #define SOCFPGA_SDR_ADDRESS			0xffcfb000
+#define SOCFPGA_NOC_L4_PRIV_FLT_OFST        	0xffd11000
+#define SOCFPGA_NOC_FW_H2F_SCR_OFST		0xffd13500
 #define SOCFPGA_SDR_SCHEDULER_ADDRESS		0xffd12400
 #define SOCFPGA_SDR_FIREWALL_OCRAM_ADDRESS	0xffd13200
 #define SOCFPGA_SDR_FIREWALL_MPU_FPGA_ADDRESS	0xffd13300

index 9e1c3fd..e1f0082 100644
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2013 Altera Corporation <www.altera.com>
+ * Copyright (C) 2013-2016 Altera Corporation <www.altera.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

@@ -11,8 +11,10 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
 static struct socfpga_system_manager *sysmgr_regs =
 	(struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS;
+#endif
 
 /*
  * Populate the value for SYSMGR.FPGAINTF.MODULE based on pinmux setting.

index bfefafd..7fd922e 100644
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2012 Altera Corporation <www.altera.com>
+ * Copyright (C) 2012-2016 Altera Corporation <www.altera.com>
  * All rights reserved.
  *
  * SPDX-License-Identifier:	BSD-3-Clause

@@ -19,8 +19,10 @@ DECLARE_GLOBAL_DATA_PTR;
 
 static struct socfpga_fpga_manager *fpgamgr_regs =
 	(struct socfpga_fpga_manager *)SOCFPGA_FPGAMGRREGS_ADDRESS;
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
 static struct socfpga_system_manager *sysmgr_regs =
 	(struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS;
+#endif
 
 /* Set CD ratio */
 static void fpgamgr_set_cd_ratio(unsigned long ratio)

@@ -267,9 +269,10 @@ int socfpga_load(Altera_desc *desc, const void *rbf_data, size_t rbf_size)
 	}
 
 	/* Prior programming the FPGA, all bridges need to be shut off */
-
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
 	/* Disable all signals from hps peripheral controller to fpga */
 	writel(0, &sysmgr_regs->fpgaintfgrp_module);
+#endif
 
 	/* Disable all signals from FPGA to HPS SDRAM */
 #define SDR_CTRLGRP_FPGAPORTRST_ADDRESS	0x5080

100 lines not on this page · raw message

index bbbde1e..fde9a51 100644
@@ -15,7 +15,9 @@
  * High level configuration
  */
 #define CONFIG_DISPLAY_BOARDINFO_LATE
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
 #define CONFIG_ARCH_MISC_INIT
+#endif
 #define CONFIG_ARCH_EARLY_INIT_R
 #define CONFIG_SYS_NO_FLASH
 #define CONFIG_CLOCKS

@@ -37,9 +39,13 @@
 #define CONFIG_SYS_MALLOC_LEN		(64 * 1024 * 1024)
 #define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM_1
 #define CONFIG_SYS_MEMTEST_END		PHYS_SDRAM_1_SIZE
-
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
 #define CONFIG_SYS_INIT_RAM_ADDR	0xFFFF0000
 #define CONFIG_SYS_INIT_RAM_SIZE	0x10000
+#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+#define CONFIG_SYS_INIT_RAM_ADDR	0xFFE00000
+#define CONFIG_SYS_INIT_RAM_SIZE	0x40000 /* 256KB */
+#endif
 #define CONFIG_SYS_INIT_SP_OFFSET		\
 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_ADDR			\

@@ -213,11 +219,14 @@ unsigned int cm_get_qspi_controller_clk_hz(void);
  */
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	-4
-#define CONFIG_SYS_NS16550_COM1		SOCFPGA_UART0_ADDRESS
 #ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
 #define CONFIG_SYS_NS16550_CLK		1000000
-#else
+#elif defined(CONFIG_TARGET_SOCFPGA_GEN5)
+#define CONFIG_SYS_NS16550_COM1		SOCFPGA_UART0_ADDRESS
 #define CONFIG_SYS_NS16550_CLK		100000000
+#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+#define CONFIG_SYS_NS16550_COM1        SOCFPGA_UART1_ADDRESS
+#define CONFIG_SYS_NS16550_CLK         	50000000
 #endif
 #define CONFIG_CONS_INDEX		1
 #define CONFIG_BAUDRATE			115200

@@ -295,23 +304,39 @@ unsigned int cm_get_qspi_controller_clk_hz(void);
 /*
  * SPL
  *
- * SRAM Memory layout:
+ * SRAM Memory layout(TARGET_SOCFPGA_GEN5):
  *
  * 0xFFFF_0000 ...... Start of SRAM
  * 0xFFFF_xxxx ...... Top of stack (grows down)
  * 0xFFFF_yyyy ...... Malloc area
  * 0xFFFF_zzzz ...... Global Data
  * 0xFFFF_FF00 ...... End of SRAM
+ *
+ * SRAM Memory layout(TARGET_SOCFPGA_ARRIA10):
+ *
+ * 0xFFE0_0000 ...... Start of SRAM
+ * 0xFFE0_xxxx ...... Top of stack (grows down)
+ * 0xFFE0_yyyy ...... Malloc area
+ * 0xFFE0_zzzz ...... Global Data
+ * 0xFFE3_FFFF ...... End of SRAM
  */
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_RAM_DEVICE
 #define CONFIG_SPL_TEXT_BASE		CONFIG_SYS_INIT_RAM_ADDR
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
 #define CONFIG_SPL_MAX_SIZE		(64 * 1024)
+#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+#define CONFIG_SPL_MAX_SIZE		CONFIG_SYS_INIT_RAM_SIZE
+#endif
 
 /* SPL SDMMC boot support */
 #ifdef CONFIG_SPL_MMC_SUPPORT
 #if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT)
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	2
+#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
+#endif
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot-dtb.img"
 #else
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION	1

188 lines not on this page · raw message

131 lines not on this page · raw message

407 lines not on this page · raw message

137 lines not on this page · raw message

new file mode 100644
index 0000000..045268d
@@ -0,0 +1,32 @@
+/*
+ * Copyright (C) 2016, Intel Corporation
+ *
+ * SPDX-License-Identifier:    GPL-2.0
+ */
+
+#ifndef _MISC_H_
+#define	_MISC_H_
+
+extern void dwmac_deassert_reset(const unsigned int of_reset_id,
+				 const u32 phymode);
+
+struct bsel{
+	const char	*mode;
+	const char	*name;
+};
+
+extern struct bsel bsel_str[];
+
+#ifdef CONFIG_FPGA
+extern void socfpga_fpga_add(void);
+#else
+inline void socfpga_fpga_add(void) {}
+#endif
+
+#if defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+unsigned int dedicated_uart_com_port(const void *blob);
+unsigned int shared_uart_com_port(const void *blob);
+unsigned int uart_com_port(const void *blob);
+#endif
+
+#endif /* _MISC_H_ */

472 lines not on this page · raw message

255 lines not on this page · raw message

320 lines not on this page · raw message

index aa71636..d209f7d 100644
@@ -1,5 +1,5 @@
 /*
- *  Copyright (C) 2013 Altera Corporation <www.altera.com>
+ *  Copyright (C) 2013-2016 Altera Corporation <www.altera.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

@@ -7,416 +7,287 @@
 #include <common.h>
 #include <asm/io.h>
 #include <asm/arch/clock_manager.h>
+#include <fdtdec.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
+/* Function prototypes */
+/* Common prototypes */
+unsigned int cm_get_l4_sp_clk_hz(void);
+unsigned int cm_get_qspi_controller_clk_hz(void);
+unsigned int cm_get_mmc_controller_clk_hz(void);
+unsigned int cm_get_spi_controller_clk_hz(void);
+static void cm_print_clock_quick_summary(void);
+int do_showclocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]);
+void cm_wait_for_lock(uint32_t mask);
+void cm_wait_for_fsm(void);
+unsigned int cm_get_main_vco_clk_hz(void);
+unsigned int cm_get_per_vco_clk_hz(void);
+unsigned long cm_get_mpu_clk_hz(void);
+
 static const struct socfpga_clock_manager *clock_manager_base =
 	(struct socfpga_clock_manager *)SOCFPGA_CLKMGR_ADDRESS;
 
-static void cm_wait_for_lock(uint32_t mask)
+/* Common functions */
+int set_cpu_clk_info(void)
 {
-	register uint32_t inter_val;
-	uint32_t retry = 0;
-	do {
-		inter_val = readl(&clock_manager_base->inter) & mask;
-		if (inter_val == mask)
-			retry++;
-		else
-			retry = 0;
-		if (retry >= 10)
-			break;
-	} while (1);
-}
+	/* Calculate the clock frequencies required for drivers */
+	cm_get_l4_sp_clk_hz();
+	cm_get_mmc_controller_clk_hz();
 
-/* function to poll in the fsm busy bit */
-static void cm_wait_for_fsm(void)
-{
-	while (readl(&clock_manager_base->stat) & CLKMGR_STAT_BUSY)
-		;
-}
+	gd->bd->bi_arm_freq = cm_get_mpu_clk_hz() / 1000000;
+	gd->bd->bi_dsp_freq = 0;
 
-/*
- * function to write the bypass register which requires a poll of the
- * busy bit
- */
-static void cm_write_bypass(uint32_t val)
-{
-	writel(val, &clock_manager_base->bypass);
-	cm_wait_for_fsm();
-}
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
+	gd->bd->bi_ddr_freq = cm_get_sdram_clk_hz() / 1000000;
+#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+	gd->bd->bi_ddr_freq = 0;
+#endif
 
-/* function to write the ctrl register which requires a poll of the busy bit */
-static void cm_write_ctrl(uint32_t val)
-{
-	writel(val, &clock_manager_base->ctrl);
-	cm_wait_for_fsm();
+	return 0;
 }
 
-/* function to write a clock register that has phase information */
-static void cm_write_with_phase(uint32_t value,
-				uint32_t reg_address, uint32_t mask)
+unsigned int cm_get_spi_controller_clk_hz(void)
 {
-	/* poll until phase is zero */
-	while (readl(reg_address) & mask)
-		;
+	uint32_t clock = 0;
 
-	writel(value, reg_address);
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
+	uint32_t reg;
+	clock = cm_get_per_vco_clk_hz();
 
-	while (readl(reg_address) & mask)
-		;
-}
+	/* get the clock prior L4 SP divider (periph_base_clk) */
+	reg = readl(&clock_manager_base->per_pll.perbaseclk);
+	clock /= (reg + 1);
+#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+	clock = cm_get_l4_noc_hz(CLKMGR_MAINPLL_NOCDIV_L4MPCLK_LSB);
+#endif
 
-/*
- * Setup clocks while making no assumptions about previous state of the clocks.
- *
- * Start by being paranoid and gate all sw managed clocks
- * Put all plls in bypass
- * Put all plls VCO registers back to reset value (bandgap power down).
- * Put peripheral and main pll src to reset value to avoid glitch.
- * Delay 5 us.
- * Deassert bandgap power down and set numerator and denominator
- * Start 7 us timer.
- * set internal dividers
- * Wait for 7 us timer.
- * Enable plls
- * Set external dividers while plls are locking
- * Wait for pll lock
- * Assert/deassert outreset all.
- * Take all pll's out of bypass
- * Clear safe mode
- * set source main and peripheral clocks
- * Ungate clocks
- */
+	return clock;
+}
 
-void cm_basic_init(const struct cm_config * const cfg)
+unsigned int cm_get_qspi_controller_clk_hz(void)
 {
-	unsigned long end;
-
-	/* Start by being paranoid and gate all sw managed clocks */
-
-	/*
-	 * We need to disable nandclk
-	 * and then do another apb access before disabling
-	 * gatting off the rest of the periperal clocks.
-	 */
-	writel(~CLKMGR_PERPLLGRP_EN_NANDCLK_MASK &
-		readl(&clock_manager_base->per_pll.en),
-		&clock_manager_base->per_pll.en);
-
-	/* DO NOT GATE OFF DEBUG CLOCKS & BRIDGE CLOCKS */
-	writel(CLKMGR_MAINPLLGRP_EN_DBGTIMERCLK_MASK |
-		CLKMGR_MAINPLLGRP_EN_DBGTRACECLK_MASK |
-		CLKMGR_MAINPLLGRP_EN_DBGCLK_MASK |
-		CLKMGR_MAINPLLGRP_EN_DBGATCLK_MASK |
-		CLKMGR_MAINPLLGRP_EN_S2FUSER0CLK_MASK |
-		CLKMGR_MAINPLLGRP_EN_L4MPCLK_MASK,
-		&clock_manager_base->main_pll.en);
-
-	writel(0, &clock_manager_base->sdr_pll.en);
-
-	/* now we can gate off the rest of the peripheral clocks */
-	writel(0, &clock_manager_base->per_pll.en);
-
-	/* Put all plls in bypass */
-	cm_write_bypass(CLKMGR_BYPASS_PERPLL | CLKMGR_BYPASS_SDRPLL |
-			CLKMGR_BYPASS_MAINPLL);
-
-	/* Put all plls VCO registers back to reset value. */
-	writel(CLKMGR_MAINPLLGRP_VCO_RESET_VALUE &
-	       ~CLKMGR_MAINPLLGRP_VCO_REGEXTSEL_MASK,
-	       &clock_manager_base->main_pll.vco);
-	writel(CLKMGR_PERPLLGRP_VCO_RESET_VALUE &
-	       ~CLKMGR_PERPLLGRP_VCO_REGEXTSEL_MASK,
-	       &clock_manager_base->per_pll.vco);
-	writel(CLKMGR_SDRPLLGRP_VCO_RESET_VALUE &
-	       ~CLKMGR_SDRPLLGRP_VCO_REGEXTSEL_MASK,
-	       &clock_manager_base->sdr_pll.vco);
-
-	/*
-	 * The clocks to the flash devices and the L4_MAIN clocks can
-	 * glitch when coming out of safe mode if their source values
-	 * are different from their reset value.  So the trick it to
-	 * put them back to their reset state, and change input
-	 * after exiting safe mode but before ungating the clocks.
-	 */
-	writel(CLKMGR_PERPLLGRP_SRC_RESET_VALUE,
-	       &clock_manager_base->per_pll.src);
-	writel(CLKMGR_MAINPLLGRP_L4SRC_RESET_VALUE,
-	       &clock_manager_base->main_pll.l4src);
-
-	/* read back for the required 5 us delay. */
-	readl(&clock_manager_base->main_pll.vco);
-	readl(&clock_manager_base->per_pll.vco);
-	readl(&clock_manager_base->sdr_pll.vco);
-
-
-	/*
-	 * We made sure bgpwr down was assert for 5 us. Now deassert BG PWR DN
-	 * with numerator and denominator.
-	 */
-	writel(cfg->main_vco_base, &clock_manager_base->main_pll.vco);
-	writel(cfg->peri_vco_base, &clock_manager_base->per_pll.vco);
-	writel(cfg->sdram_vco_base, &clock_manager_base->sdr_pll.vco);
-
-	/*
-	 * Time starts here. Must wait 7 us from
-	 * BGPWRDN_SET(0) to VCO_ENABLE_SET(1).
-	 */
-	end = timer_get_us() + 7;
-
-	/* main mpu */
-	writel(cfg->mpuclk, &clock_manager_base->main_pll.mpuclk);
-
-	/* main main clock */
-	writel(cfg->mainclk, &clock_manager_base->main_pll.mainclk);
-
-	/* main for dbg */
-	writel(cfg->dbgatclk, &clock_manager_base->main_pll.dbgatclk);
-
-	/* main for cfgs2fuser0clk */
-	writel(cfg->cfg2fuser0clk,
-	       &clock_manager_base->main_pll.cfgs2fuser0clk);
-
-	/* Peri emac0 50 MHz default to RMII */
-	writel(cfg->emac0clk, &clock_manager_base->per_pll.emac0clk);
-
-	/* Peri emac1 50 MHz default to RMII */
-	writel(cfg->emac1clk, &clock_manager_base->per_pll.emac1clk);
-
-	/* Peri QSPI */
-	writel(cfg->mainqspiclk, &clock_manager_base->main_pll.mainqspiclk);
-
-	writel(cfg->perqspiclk, &clock_manager_base->per_pll.perqspiclk);
-
-	/* Peri pernandsdmmcclk */
-	writel(cfg->mainnandsdmmcclk,
-	       &clock_manager_base->main_pll.mainnandsdmmcclk);
-
-	writel(cfg->pernandsdmmcclk,
-	       &clock_manager_base->per_pll.pernandsdmmcclk);
-
-	/* Peri perbaseclk */
-	writel(cfg->perbaseclk, &clock_manager_base->per_pll.perbaseclk);
-
-	/* Peri s2fuser1clk */
-	writel(cfg->s2fuser1clk, &clock_manager_base->per_pll.s2fuser1clk);
-
-	/* 7 us must have elapsed before we can enable the VCO */
-	while (timer_get_us() < end)
-		;
-
-	/* Enable vco */
-	/* main pll vco */
-	writel(cfg->main_vco_base | CLKMGR_MAINPLLGRP_VCO_EN,
-	       &clock_manager_base->main_pll.vco);
+	uint32_t clock = 0;
 
-	/* periferal pll */
-	writel(cfg->peri_vco_base | CLKMGR_MAINPLLGRP_VCO_EN,
-	       &clock_manager_base->per_pll.vco);
-
-	/* sdram pll vco */
-	writel(cfg->sdram_vco_base | CLKMGR_MAINPLLGRP_VCO_EN,
-	       &clock_manager_base->sdr_pll.vco);
-
-	/* L3 MP and L3 SP */
-	writel(cfg->maindiv, &clock_manager_base->main_pll.maindiv);
-
-	writel(cfg->dbgdiv, &clock_manager_base->main_pll.dbgdiv);
-
-	writel(cfg->tracediv, &clock_manager_base->main_pll.tracediv);
-
-	/* L4 MP, L4 SP, can0, and can1 */
-	writel(cfg->perdiv, &clock_manager_base->per_pll.div);
-
-	writel(cfg->gpiodiv, &clock_manager_base->per_pll.gpiodiv);
-
-#define LOCKED_MASK \
-	(CLKMGR_INTER_SDRPLLLOCKED_MASK  | \
-	CLKMGR_INTER_PERPLLLOCKED_MASK  | \
-	CLKMGR_INTER_MAINPLLLOCKED_MASK)
-
-	cm_wait_for_lock(LOCKED_MASK);
-
-	/* write the sdram clock counters before toggling outreset all */
-	writel(cfg->ddrdqsclk & CLKMGR_SDRPLLGRP_DDRDQSCLK_CNT_MASK,
-	       &clock_manager_base->sdr_pll.ddrdqsclk);
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
+	uint32_t reg;
+	/* identify the source of QSPI clock */
+	reg = readl(&clock_manager_base->per_pll.src);
+	reg = (reg & CLKMGR_PERPLLGRP_SRC_QSPI_MASK) >>
+	      CLKMGR_PERPLLGRP_SRC_QSPI_OFFSET;
 
-	writel(cfg->ddr2xdqsclk & CLKMGR_SDRPLLGRP_DDR2XDQSCLK_CNT_MASK,
-	       &clock_manager_base->sdr_pll.ddr2xdqsclk);
+	if (reg == CLKMGR_QSPI_CLK_SRC_F2S) {
+		clock = cm_get_f2s_per_ref_clk_hz();
+	} else if (reg == CLKMGR_QSPI_CLK_SRC_MAIN) {
+		clock = cm_get_main_vco_clk_hz();
 
-	writel(cfg->ddrdqclk & CLKMGR_SDRPLLGRP_DDRDQCLK_CNT_MASK,
-	       &clock_manager_base->sdr_pll.ddrdqclk);
+		/* get the qspi clock */
+		reg = readl(&clock_manager_base->main_pll.mainqspiclk);
+		clock /= (reg + 1);
+	} else if (reg == CLKMGR_QSPI_CLK_SRC_PER) {
+		clock = cm_get_per_vco_clk_hz();
 
-	writel(cfg->s2fuser2clk & CLKMGR_SDRPLLGRP_S2FUSER2CLK_CNT_MASK,
-	       &clock_manager_base->sdr_pll.s2fuser2clk);
+		/* get the qspi clock */
+		reg = readl(&clock_manager_base->per_pll.perqspiclk);
+		clock /= (reg + 1);
+	}
+#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+	clock = cm_get_l4_noc_hz(CLKMGR_MAINPLL_NOCDIV_L4MAINCLK_LSB);
+#endif
 
-	/*
-	 * after locking, but before taking out of bypass
-	 * assert/deassert outresetall
-	 */
-	uint32_t mainvco = readl(&clock_manager_base->main_pll.vco);
+	return clock;
+}
 
-	/* assert main outresetall */
-	writel(mainvco | CLKMGR_MAINPLLGRP_VCO_OUTRESETALL_MASK,
-	       &clock_manager_base->main_pll.vco);
+void cm_wait_for_lock(uint32_t mask)
+{
+	register uint32_t inter_val;
+	uint32_t retry = 0;
+	do {
+#if defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+		inter_val = readl(&clock_manager_base->stat) & mask;
+#elif defined(CONFIG_TARGET_SOCFPGA_GEN5)
+		inter_val = readl(&clock_manager_base->inter) & mask;
+#endif
+		/* Wait for stable lock */
+		if (inter_val == mask)
+			retry++;
+		else
+			retry = 0;
+		if (retry >= 10)
+			break;
+	} while (1);
+}
 
-	uint32_t periphvco = readl(&clock_manager_base->per_pll.vco);
+unsigned long cm_get_mpu_clk_hz(void)
+{
+	uint32_t reg, clk_hz;
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
+	clk_hz = cm_get_main_vco_clk_hz();
 
-	/* assert pheriph outresetall */
-	writel(periphvco | CLKMGR_PERPLLGRP_VCO_OUTRESETALL_MASK,
-	       &clock_manager_base->per_pll.vco);
+	/* get the MPU clock */
+	reg = readl(&clock_manager_base->altera.mpuclk);
+	clk_hz /= (reg + 1);
+	reg = readl(&clock_manager_base->main_pll.mpuclk);
+	clk_hz /= (reg + 1);
+#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+	uint32_t clk_src, mainmpuclk_reg;
 
-	/* assert sdram outresetall */
-	writel(cfg->sdram_vco_base | CLKMGR_MAINPLLGRP_VCO_EN|
-		CLKMGR_SDRPLLGRP_VCO_OUTRESETALL,
-		&clock_manager_base->sdr_pll.vco);
+	mainmpuclk_reg = readl(&clock_manager_base->main_pll.mpuclk);
 
-	/* deassert main outresetall */
-	writel(mainvco & ~CLKMGR_MAINPLLGRP_VCO_OUTRESETALL_MASK,
-	       &clock_manager_base->main_pll.vco);
+	clk_src = (mainmpuclk_reg >> CLKMGR_MAINPLL_MPUCLK_SRC_LSB) &
+		CLKMGR_MAINPLL_MPUCLK_SRC_MSK;
 
-	/* deassert pheriph outresetall */
-	writel(periphvco & ~CLKMGR_PERPLLGRP_VCO_OUTRESETALL_MASK,
-	       &clock_manager_base->per_pll.vco);
+	reg = readl(&clock_manager_base->altera.mpuclk);
+	/* Check MPU clock source: main, periph, osc1, intosc or f2s? */
+	switch (clk_src) {
+	case CLKMGR_MAINPLL_MPUCLK_SRC_MAIN:
+		clk_hz = cm_get_main_vco_clk_hz();
+		clk_hz /= ((reg & CLKMGR_MAINPLL_MPUCLK_CNT_MSK)
+			   + 1);
+		break;
+	case CLKMGR_MAINPLL_MPUCLK_SRC_PERI:
+		clk_hz = cm_get_per_vco_clk_hz();
+		clk_hz /= (((reg >> CLKMGR_MAINPLL_MPUCLK_PERICNT_LSB) &
+			   CLKMGR_MAINPLL_MPUCLK_CNT_MSK) + 1);
+		break;
+	case CLKMGR_MAINPLL_MPUCLK_SRC_OSC1:
+		clk_hz = eosc1_hz;
+		break;
+	case CLKMGR_MAINPLL_MPUCLK_SRC_INTOSC:
+		clk_hz = cb_intosc_hz;
+		break;
+	case CLKMGR_MAINPLL_MPUCLK_SRC_FPGA:
+		clk_hz = f2s_free_hz;
+		break;
+	default:
+		printf("cm_get_mpu_clk_hz invalid clk_src %d\n", clk_src);
+		return 0;
+	}
 
-	/* deassert sdram outresetall */
-	writel(cfg->sdram_vco_base | CLKMGR_MAINPLLGRP_VCO_EN,
-	       &clock_manager_base->sdr_pll.vco);
+	clk_hz /= ((mainmpuclk_reg & CLKMGR_MAINPLL_MPUCLK_CNT_MSK) + 1);
+#endif
 
-	/*
-	 * now that we've toggled outreset all, all the clocks
-	 * are aligned nicely; so we can change any phase.
-	 */
-	cm_write_with_phase(cfg->ddrdqsclk,
-			    (uint32_t)&clock_manager_base->sdr_pll.ddrdqsclk,
-			    CLKMGR_SDRPLLGRP_DDRDQSCLK_PHASE_MASK);
+	return clk_hz;
+}
 
-	/* SDRAM DDR2XDQSCLK */
-	cm_write_with_phase(cfg->ddr2xdqsclk,
-			    (uint32_t)&clock_manager_base->sdr_pll.ddr2xdqsclk,
-			    CLKMGR_SDRPLLGRP_DDR2XDQSCLK_PHASE_MASK);
+unsigned int cm_get_per_vco_clk_hz(void)
+{
+	uint32_t src_hz = 0;
+	uint32_t clk_src = 0;
+	uint32_t numer = 0;
+	uint32_t denom = 0;
+	uint32_t vco = 0;
 
-	cm_write_with_phase(cfg->ddrdqclk,
-			    (uint32_t)&clock_manager_base->sdr_pll.ddrdqclk,
-			    CLKMGR_SDRPLLGRP_DDRDQCLK_PHASE_MASK);
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
+	/* identify PER PLL clock source */
+	clk_src = readl(&clock_manager_base->per_pll.vco);
+	clk_src = (clk_src & CLKMGR_PERPLLGRP_VCO_SSRC_MASK) >>
+	      CLKMGR_PERPLLGRP_VCO_SSRC_OFFSET;
+	if (clk_src == CLKMGR_VCO_SSRC_EOSC1)
+		src_hz = cm_get_osc_clk_hz(1);
+	else if (clk_src == CLKMGR_VCO_SSRC_EOSC2)
+		src_hz = cm_get_osc_clk_hz(2);
+	else if (clk_src == CLKMGR_VCO_SSRC_F2S)
+		src_hz = cm_get_f2s_per_ref_clk_hz();
 
-	cm_write_with_phase(cfg->s2fuser2clk,
-			    (uint32_t)&clock_manager_base->sdr_pll.s2fuser2clk,
-			    CLKMGR_SDRPLLGRP_S2FUSER2CLK_PHASE_MASK);
+	/* get the PER VCO clock */
+	vco = readl(&clock_manager_base->per_pll.vco);
+
+	numer = (vco & CLKMGR_PERPLLGRP_VCO_NUMER_MASK) >>
+		CLKMGR_PERPLLGRP_VCO_NUMER_OFFSET;
+
+	denom = (vco & CLKMGR_PERPLLGRP_VCO_DENOM_MASK) >>
+		CLKMGR_PERPLLGRP_VCO_DENOM_OFFSET;
+
+#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+	clk_src = readl(&clock_manager_base->per_pll.vco0);
+
+	clk_src = (clk_src >> CLKMGR_PERPLL_VCO0_PSRC_LSB) &
+		CLKMGR_PERPLL_VCO0_PSRC_MSK;
+
+	if (clk_src == CLKMGR_PERPLL_VCO0_PSRC_EOSC) {
+		src_hz = eosc1_hz;
+	} else if (clk_src == CLKMGR_PERPLL_VCO0_PSRC_E_INTOSC) {
+		src_hz = cb_intosc_hz;
+	} else if (clk_src == CLKMGR_PERPLL_VCO0_PSRC_F2S) {
+		src_hz = f2s_free_hz;
+	} else if (clk_src == CLKMGR_PERPLL_VCO0_PSRC_MAIN) {
+		src_hz = cm_get_main_vco_clk_hz();
+		src_hz /= (readl
+			(&clock_manager_base->main_pll.cntr15clk) &
+			CLKMGR_MAINPLL_CNTRCLK_MSK) + 1;
+	} else {
+		printf("cm_get_per_vco_clk_hz invalid clk_src %d\n", clk_src);
+		return 0;
+	}
 
-	/* Take all three PLLs out of bypass when safe mode is cleared. */
-	cm_write_bypass(0);
+	vco = readl(&clock_manager_base->per_pll.vco1);
 
-	/* clear safe mode */
-	cm_write_ctrl(readl(&clock_manager_base->ctrl) | CLKMGR_CTRL_SAFEMODE);
+	numer = vco & CLKMGR_PERPLL_VCO1_NUMER_MSK;
 
-	/*
-	 * now that safe mode is clear with clocks gated
-	 * it safe to change the source mux for the flashes the the L4_MAIN
-	 */
-	writel(cfg->persrc, &clock_manager_base->per_pll.src);
-	writel(cfg->l4src, &clock_manager_base->main_pll.l4src);
+	denom = (vco >> CLKMGR_PERPLL_VCO1_DENOM_LSB) &
+			CLKMGR_PERPLL_VCO1_DENOM_MSK;
+#endif
 
-	/* Now ungate non-hw-managed clocks */
-	writel(~0, &clock_manager_base->main_pll.en);
-	writel(~0, &clock_manager_base->per_pll.en);
-	writel(~0, &clock_manager_base->sdr_pll.en);
+	vco = src_hz;
+	vco /= (1 + denom);
+	vco *= (1 + numer);
 
-	/* Clear the loss of lock bits (write 1 to clear) */
-	writel(CLKMGR_INTER_SDRPLLLOST_MASK | CLKMGR_INTER_PERPLLLOST_MASK |
-	       CLKMGR_INTER_MAINPLLLOST_MASK,
-	       &clock_manager_base->inter);
+	return vco;
 }
 
-static unsigned int cm_get_main_vco_clk_hz(void)
+unsigned int cm_get_main_vco_clk_hz(void)
 {
-	uint32_t reg, clock;
+	uint32_t src_hz, numer, denom, vco;
 
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
 	/* get the main VCO clock */
-	reg = readl(&clock_manager_base->main_pll.vco);
-	clock = cm_get_osc_clk_hz(1);
-	clock /= ((reg & CLKMGR_MAINPLLGRP_VCO_DENOM_MASK) >>
-		  CLKMGR_MAINPLLGRP_VCO_DENOM_OFFSET) + 1;
-	clock *= ((reg & CLKMGR_MAINPLLGRP_VCO_NUMER_MASK) >>
-		  CLKMGR_MAINPLLGRP_VCO_NUMER_OFFSET) + 1;
-
-	return clock;
-}
-
-static unsigned int cm_get_per_vco_clk_hz(void)
-{
-	uint32_t reg, clock = 0;
-
-	/* identify PER PLL clock source */
-	reg = readl(&clock_manager_base->per_pll.vco);
-	reg = (reg & CLKMGR_PERPLLGRP_VCO_SSRC_MASK) >>
-	      CLKMGR_PERPLLGRP_VCO_SSRC_OFFSET;
-	if (reg == CLKMGR_VCO_SSRC_EOSC1)
-		clock = cm_get_osc_clk_hz(1);
-	else if (reg == CLKMGR_VCO_SSRC_EOSC2)
-		clock = cm_get_osc_clk_hz(2);
-	else if (reg == CLKMGR_VCO_SSRC_F2S)
-		clock = cm_get_f2s_per_ref_clk_hz();
-
-	/* get the PER VCO clock */
-	reg = readl(&clock_manager_base->per_pll.vco);
-	clock /= ((reg & CLKMGR_PERPLLGRP_VCO_DENOM_MASK) >>
-		  CLKMGR_PERPLLGRP_VCO_DENOM_OFFSET) + 1;
-	clock *= ((reg & CLKMGR_PERPLLGRP_VCO_NUMER_MASK) >>
-		  CLKMGR_PERPLLGRP_VCO_NUMER_OFFSET) + 1;
-
-	return clock;
-}
+	vco = readl(&clock_manager_base->main_pll.vco);
+
+	numer = ((vco & CLKMGR_MAINPLLGRP_VCO_NUMER_MASK) >>
+		CLKMGR_MAINPLLGRP_VCO_NUMER_OFFSET);
+	denom = ((vco & CLKMGR_MAINPLLGRP_VCO_DENOM_MASK) >>
+		 CLKMGR_MAINPLLGRP_VCO_DENOM_OFFSET);
+
+	src_hz = cm_get_osc_clk_hz(1);
+#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+	uint32_t clk_src = readl(&clock_manager_base->main_pll.vco0);
+
+	clk_src = (clk_src >> CLKMGR_MAINPLL_VCO0_PSRC_LSB) &
+		CLKMGR_MAINPLL_VCO0_PSRC_MSK;
+
+	if (clk_src == CLKMGR_MAINPLL_VCO0_PSRC_EOSC) {
+		src_hz = eosc1_hz;
+	} else if (clk_src == CLKMGR_MAINPLL_VCO0_PSRC_E_INTOSC) {
+		src_hz = cb_intosc_hz;
+	} else if (clk_src == CLKMGR_MAINPLL_VCO0_PSRC_F2S) {
+		src_hz = f2s_free_hz;
+	} else {
+		printf("cm_get_main_vco_clk_hz invalid clk_src %d\n", clk_src);
+		return 0;
+	}
 
-unsigned long cm_get_mpu_clk_hz(void)
-{
-	uint32_t reg, clock;
+	vco = readl(&clock_manager_base->main_pll.vco1);
 
-	clock = cm_get_main_vco_clk_hz();
+	numer = vco & CLKMGR_MAINPLL_VCO1_NUMER_MSK;
 
-	/* get the MPU clock */
-	reg = readl(&clock_manager_base->altera.mpuclk);
-	clock /= (reg + 1);
-	reg = readl(&clock_manager_base->main_pll.mpuclk);
-	clock /= (reg + 1);
-	return clock;
-}
+	denom = (vco >> CLKMGR_MAINPLL_VCO1_DENOM_LSB) &
+			CLKMGR_MAINPLL_VCO1_DENOM_MSK;
+#endif
 
-unsigned long cm_get_sdram_clk_hz(void)
-{
-	uint32_t reg, clock = 0;
-
-	/* identify SDRAM PLL clock source */
-	reg = readl(&clock_manager_base->sdr_pll.vco);
-	reg = (reg & CLKMGR_SDRPLLGRP_VCO_SSRC_MASK) >>
-	      CLKMGR_SDRPLLGRP_VCO_SSRC_OFFSET;
-	if (reg == CLKMGR_VCO_SSRC_EOSC1)
-		clock = cm_get_osc_clk_hz(1);
-	else if (reg == CLKMGR_VCO_SSRC_EOSC2)
-		clock = cm_get_osc_clk_hz(2);
-	else if (reg == CLKMGR_VCO_SSRC_F2S)
-		clock = cm_get_f2s_sdr_ref_clk_hz();
-
-	/* get the SDRAM VCO clock */
-	reg = readl(&clock_manager_base->sdr_pll.vco);
-	clock /= ((reg & CLKMGR_SDRPLLGRP_VCO_DENOM_MASK) >>
-		  CLKMGR_SDRPLLGRP_VCO_DENOM_OFFSET) + 1;
-	clock *= ((reg & CLKMGR_SDRPLLGRP_VCO_NUMER_MASK) >>
-		  CLKMGR_SDRPLLGRP_VCO_NUMER_OFFSET) + 1;
-
-	/* get the SDRAM (DDR_DQS) clock */
-	reg = readl(&clock_manager_base->sdr_pll.ddrdqsclk);
-	reg = (reg & CLKMGR_SDRPLLGRP_DDRDQSCLK_CNT_MASK) >>
-	      CLKMGR_SDRPLLGRP_DDRDQSCLK_CNT_OFFSET;
-	clock /= (reg + 1);
+	vco = src_hz;
+	vco /= (1 + denom);
+	vco *= (1 + numer);
 
-	return clock;
+	return vco;
 }
 
 unsigned int cm_get_l4_sp_clk_hz(void)
 {
-	uint32_t reg, clock = 0;
+	uint32_t clock = 0;
 
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
+	uint32_t reg;
 	/* identify the source of L4 SP clock */
 	reg = readl(&clock_manager_base->main_pll.l4src);
 	reg = (reg & CLKMGR_MAINPLLGRP_L4SRC_L4SP) >>

@@ -443,106 +314,117 @@ unsigned int cm_get_l4_sp_clk_hz(void)
 	reg = (reg & CLKMGR_MAINPLLGRP_MAINDIV_L4SPCLK_MASK) >>
 	      CLKMGR_MAINPLLGRP_MAINDIV_L4SPCLK_OFFSET;
 	clock = clock / (1 << reg);
-
+#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+	clock = cm_get_l4_noc_hz(CLKMGR_MAINPLL_NOCDIV_L4SPCLK_LSB);
+#endif
 	return clock;
 }
 
-unsigned int cm_get_mmc_controller_clk_hz(void)
+/* function to poll in the fsm busy bit */
+void cm_wait_for_fsm(void)
 {
-	uint32_t reg, clock = 0;
-
-	/* identify the source of MMC clock */
-	reg = readl(&clock_manager_base->per_pll.src);
-	reg = (reg & CLKMGR_PERPLLGRP_SRC_SDMMC_MASK) >>
-	      CLKMGR_PERPLLGRP_SRC_SDMMC_OFFSET;
-
-	if (reg == CLKMGR_SDMMC_CLK_SRC_F2S) {
-		clock = cm_get_f2s_per_ref_clk_hz();
-	} else if (reg == CLKMGR_SDMMC_CLK_SRC_MAIN) {
-		clock = cm_get_main_vco_clk_hz();
-
-		/* get the SDMMC clock */
-		reg = readl(&clock_manager_base->main_pll.mainnandsdmmcclk);
-		clock /= (reg + 1);
-	} else if (reg == CLKMGR_SDMMC_CLK_SRC_PER) {
-		clock = cm_get_per_vco_clk_hz();
-
-		/* get the SDMMC clock */
-		reg = readl(&clock_manager_base->per_pll.pernandsdmmcclk);
-		clock /= (reg + 1);
-	}
-
-	/* further divide by 4 as we have fixed divider at wrapper */
-	clock /= 4;
-	return clock;
+	while (readl(&clock_manager_base->stat) &
+		CLKMGR_CLKMGR_STAT_BUSY_SET_MSK);
 }
 
-unsigned int cm_get_qspi_controller_clk_hz(void)
+unsigned int cm_get_mmc_controller_clk_hz(void)
 {
-	uint32_t reg, clock = 0;
-
-	/* identify the source of QSPI clock */
-	reg = readl(&clock_manager_base->per_pll.src);
-	reg = (reg & CLKMGR_PERPLLGRP_SRC_QSPI_MASK) >>
-	      CLKMGR_PERPLLGRP_SRC_QSPI_OFFSET;
+	uint32_t clk_hz = 0;
+	uint32_t clk_input = 0;
+
+#if defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+	clk_input = readl(&clock_manager_base->per_pll.cntr6clk);
+	clk_input = (clk_input >> CLKMGR_PERPLL_CNTR6CLK_SRC_LSB) &
+		CLKMGR_PERPLLGRP_SRC_MSK;
+#elif defined(CONFIG_TARGET_SOCFPGA_GEN5)
+	clk_input = readl(&clock_manager_base->per_pll.src);
+	clk_input = (clk_input & CLKMGR_PERPLLGRP_SRC_SDMMC_MASK) >>
+	      CLKMGR_PERPLLGRP_SRC_SDMMC_OFFSET;
+#endif
+
+	switch (clk_input) {
+#if defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+	case CLKMGR_PERPLLGRP_SRC_MAIN:
+		clk_hz = cm_get_main_vco_clk_hz();
+		clk_hz /= 1 +
+			(readl
+			(&clock_manager_base->main_pll.cntr6clk) &
+			CLKMGR_MAINPLL_CNTRCLK_MSK);
+		break;
+
+	case CLKMGR_PERPLLGRP_SRC_PERI:
+		clk_hz = cm_get_per_vco_clk_hz();
+		clk_hz /= 1 + (readl
+			(&clock_manager_base->per_pll.cntr6clk) &
+			CLKMGR_PERPLL_CNTRCLK_MSK);
+		break;
+
+	case CLKMGR_PERPLLGRP_SRC_OSC1:
+		clk_hz = eosc1_hz;
+		break;
+
+	case CLKMGR_PERPLLGRP_SRC_INTOSC:
+		clk_hz = cb_intosc_hz;
+		break;
+
+	case CLKMGR_PERPLLGRP_SRC_FPGA:
+		clk_hz = f2s_free_hz;
+		break;
+#elif defined(CONFIG_TARGET_SOCFPGA_GEN5)
+	case CLKMGR_SDMMC_CLK_SRC_F2S:
+		clk_hz = cm_get_f2s_per_ref_clk_hz();
+		break;
+
+	case CLKMGR_SDMMC_CLK_SRC_MAIN:
+		clk_hz = cm_get_main_vco_clk_hz();
 
-	if (reg == CLKMGR_QSPI_CLK_SRC_F2S) {
-		clock = cm_get_f2s_per_ref_clk_hz();
-	} else if (reg == CLKMGR_QSPI_CLK_SRC_MAIN) {
-		clock = cm_get_main_vco_clk_hz();
+		/* get the SDMMC clock */
+		clk_input =
+			readl(&clock_manager_base->main_pll.mainnandsdmmcclk);
+		clk_hz /= (clk_input + 1);
+		break;
 
-		/* get the qspi clock */
-		reg = readl(&clock_manager_base->main_pll.mainqspiclk);
-		clock /= (reg + 1);
-	} else if (reg == CLKMGR_QSPI_CLK_SRC_PER) {
-		clock = cm_get_per_vco_clk_hz();
+	case CLKMGR_SDMMC_CLK_SRC_PER:
+		clk_hz = cm_get_per_vco_clk_hz();
 
-		/* get the qspi clock */
-		reg = readl(&clock_manager_base->per_pll.perqspiclk);
-		clock /= (reg + 1);
+		/* get the SDMMC clock */
+		clk_input =
+			readl(&clock_manager_base->per_pll.pernandsdmmcclk);
+		clk_hz /= (clk_input + 1);
+		break;
+#endif
 	}
-
-	return clock;
-}
-
-unsigned int cm_get_spi_controller_clk_hz(void)
-{
-	uint32_t reg, clock = 0;
-
-	clock = cm_get_per_vco_clk_hz();
-
-	/* get the clock prior L4 SP divider (periph_base_clk) */
-	reg = readl(&clock_manager_base->per_pll.perbaseclk);
-	clock /= (reg + 1);
-
-	return clock;
+	return clk_hz/4;
 }
 
 static void cm_print_clock_quick_summary(void)
 {
 	printf("MPU       %10ld kHz\n", cm_get_mpu_clk_hz() / 1000);
+	printf("MMC         %8d kHz\n", cm_get_mmc_controller_clk_hz() / 1000);
+	printf("QSPI        %8d kHz\n",
+		cm_get_qspi_controller_clk_hz() / 1000);
+	printf("SPI         %8d kHz\n", cm_get_spi_controller_clk_hz() / 1000);
+#if defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+	printf("EOSC1       %8d kHz\n", eosc1_hz / 1000);
+	printf("cb_intosc   %8d kHz\n", cb_intosc_hz / 1000);
+	printf("f2s_free    %8d kHz\n", f2s_free_hz / 1000);
+	printf("Main VCO    %8d kHz\n", cm_get_main_vco_clk_hz()/1000);
+	printf("NOC         %8d kHz\n", cm_get_noc_clk_hz()/1000);
+	printf("L4 Main	    %8d kHz\n",
+	       cm_get_l4_noc_hz(CLKMGR_MAINPLL_NOCDIV_L4MAINCLK_LSB)/1000);
+	printf("L4 MP       %8d kHz\n",
+	       cm_get_l4_noc_hz(CLKMGR_MAINPLL_NOCDIV_L4MPCLK_LSB)/1000);
+	printf("L4 SP       %8d kHz\n",
+	       cm_get_l4_sp_clk_hz()/1000);
+	printf("L4 sys free %8d kHz\n", cm_l4_sys_free_clk_hz/1000);
+#elif defined(CONFIG_TARGET_SOCFPGA_GEN5)
 	printf("DDR       %10ld kHz\n", cm_get_sdram_clk_hz() / 1000);
 	printf("EOSC1       %8d kHz\n", cm_get_osc_clk_hz(1) / 1000);
 	printf("EOSC2       %8d kHz\n", cm_get_osc_clk_hz(2) / 1000);
 	printf("F2S_SDR_REF %8d kHz\n", cm_get_f2s_sdr_ref_clk_hz() / 1000);
 	printf("F2S_PER_REF %8d kHz\n", cm_get_f2s_per_ref_clk_hz() / 1000);
-	printf("MMC         %8d kHz\n", cm_get_mmc_controller_clk_hz() / 1000);
-	printf("QSPI        %8d kHz\n", cm_get_qspi_controller_clk_hz() / 1000);
 	printf("UART        %8d kHz\n", cm_get_l4_sp_clk_hz() / 1000);
-	printf("SPI         %8d kHz\n", cm_get_spi_controller_clk_hz() / 1000);
-}
-
-int set_cpu_clk_info(void)
-{
-	/* Calculate the clock frequencies required for drivers */
-	cm_get_l4_sp_clk_hz();
-	cm_get_mmc_controller_clk_hz();
-
-	gd->bd->bi_arm_freq = cm_get_mpu_clk_hz() / 1000000;
-	gd->bd->bi_dsp_freq = 0;
-	gd->bd->bi_ddr_freq = cm_get_sdram_clk_hz() / 1000000;
-
-	return 0;
+#endif
 }
 
 int do_showclocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])

954 lines not on this page · raw message

275 lines not on this page · raw message

395 lines not on this page · raw message

new file mode 100644
index 0000000..ff54caa
@@ -0,0 +1,17 @@
+/*
+ * Copyright (C) 2016 Intel Corporation <www.intel.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0
+ */
+
+#ifndef	_PINMUX_H_
+#define	_PINMUX_H_
+
+#ifndef __ASSEMBLY__
+int config_dedicated_pins(const void *blob);
+int config_pins(const void *blob, const char *pin_grp);
+#endif
+
+
+
+#endif /* _PINMUX_H_ */

104 lines not on this page · raw message

index fec4c7a..d381904 100644
@@ -1,5 +1,5 @@
 /*
- *  Copyright (C) 2012 Altera Corporation <www.altera.com>
+ *  Copyright (C) 2012-2016 Altera Corporation <www.altera.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

@@ -19,37 +19,58 @@
 #include <asm/arch/sdram.h>
 #include <asm/arch/scu.h>
 #include <asm/arch/nic301.h>
+#include <asm/sections.h>
+#include <watchdog.h>
+#include <fdtdec.h>
+#if defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+#include <asm/arch/pinmux.h>
+#endif
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
+#define BOOTINFO_BSEL_SHIFT	0
+#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+#define BOOTINFO_BSEL_SHIFT	12
+#endif
+
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
 static struct pl310_regs *const pl310 =
 	(struct pl310_regs *)CONFIG_SYS_PL310_BASE;
 static struct scu_registers *scu_regs =
 	(struct scu_registers *)SOCFPGA_MPUSCU_ADDRESS;
 static struct nic301_registers *nic301_regs =
 	(struct nic301_registers *)SOCFPGA_L3REGS_ADDRESS;
-static struct socfpga_system_manager *sysmgr_regs =
+#endif
+
+static const struct socfpga_system_manager *sysmgr_regs =
 	(struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS;
 
 u32 spl_boot_device(void)
 {
 	const u32 bsel = readl(&sysmgr_regs->bootinfo);
 
-	switch (bsel & 0x7) {
+	switch ((bsel >> BOOTINFO_BSEL_SHIFT) & 0x7) {
 	case 0x1:	/* FPGA (HPS2FPGA Bridge) */
 		return BOOT_DEVICE_RAM;
 	case 0x2:	/* NAND Flash (1.8V) */
 	case 0x3:	/* NAND Flash (3.0V) */
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
 		socfpga_per_reset(SOCFPGA_RESET(NAND), 0);
+#endif
 		return BOOT_DEVICE_NAND;
 	case 0x4:	/* SD/MMC External Transceiver (1.8V) */
 	case 0x5:	/* SD/MMC Internal Transceiver (3.0V) */
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
 		socfpga_per_reset(SOCFPGA_RESET(SDMMC), 0);
 		socfpga_per_reset(SOCFPGA_RESET(DMA), 0);
+#endif
 		return BOOT_DEVICE_MMC1;
 	case 0x6:	/* QSPI Flash (1.8V) */
 	case 0x7:	/* QSPI Flash (3.0V) */
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
 		socfpga_per_reset(SOCFPGA_RESET(QSPI), 0);
+#endif
 		return BOOT_DEVICE_SPI;
 	default:
 		printf("Invalid boot device (bsel=%08x)!\n", bsel);

@@ -68,6 +89,7 @@ u32 spl_boot_mode(const u32 boot_device)
 }
 #endif
 
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
 static void socfpga_nic301_slave_ns(void)
 {
 	writel(0x1, &nic301_regs->lwhps2fpgaregs);

@@ -182,3 +204,54 @@ void board_init_f(ulong dummy)
 	/* Configure simple malloc base pointer into RAM. */
 	gd->malloc_base = CONFIG_SYS_TEXT_BASE + (1024 * 1024);
 }
+#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
+void board_init_f(ulong dummy)
+{
+	memset(__bss_start, 0, __bss_end - __bss_start);
+	/*
+	 * Configure Clock Manager to use intosc clock instead external osc to
+	 * ensure success watchdog operation. We do it as early as possible.
+	 */
+	cm_use_intosc();
+
+	watchdog_disable();
+
+	arch_early_init_r();
+
+#ifdef CONFIG_HW_WATCHDOG
+	/* release osc1 watchdog timer 0 from reset */
+	reset_deassert_osc1wd0();
+
+	/* reconfigure and enable the watchdog */
+	hw_watchdog_init();
+	WATCHDOG_RESET();
+#endif /* CONFIG_HW_WATCHDOG */
+
+#ifdef CONFIG_OF_CONTROL
+	/* We need to access to FDT as this stage */
+	/* FDT is at end of image */
+	gd->fdt_blob = (void *)(__bss_end);
+	/* Check whether we have a valid FDT or not. */
+	if (fdtdec_prepare_fdt()) {
+		panic("** CONFIG_OF_CONTROL defined but no FDT - please see "
+			"doc/README.fdt-control");
+	}
+#endif /* CONFIG_OF_CONTROL */
+
+	/* Initialize the timer */
+	timer_init();
+
+	/* configuring the clock based on handoff */
+	cm_basic_init(gd->fdt_blob);
+	WATCHDOG_RESET();
+
+	config_dedicated_pins(gd->fdt_blob);
+	WATCHDOG_RESET();
+
+	/* Release UART from reset */
+	reset_deassert_uart();
+
+	/* enable console uart printing */
+	preloader_console_init();
+}
+#endif