Add Automation Support for DP Compliance Testing (Rev 4)
Subsystems (3)
cover Add Automation Support for DP Compliance Testing (Rev 4)
This series is a rebased version of the previous series:
https://patchwork.freedesktop.org/series/16643/
DP 1.2 compliance testing can be acheived using DPR-120's CTS suite. This compliance unit sends a short pulse to initiate link training and video pattern generation compliance tests and sends a long pulse to initate EDID compliance tests. It also sets the AUTOMATED TEST REQUEST bit in Device IRQ to 1. These patches add support in the kernel to respond to these test requests sent by DPR-120. The test handler has been added for Link training/EDID and Video pattern compliance tests that gets invoked on short/long pulse sent by DPR-120. The test handler for each of the tests reads the corresponding DPCD registers to read the test parameters.
These tests need to be run with the IGT DP compliance automation tool. Link Training Tests (4.3.1.1 - 4.3.2.3):
It reads the DPCD registers to get the link rate and lane count requested by test and sends a hotplug uevent for the userspace to redo a modeset in order to train the link at the requested test parameters.
EDID Tests (4.2.2.3 - 4.2.2.6):
It reads the EDID set by the DPR-120, if EDID read succeeds, it sets the video mode to PREFERRED and sets the test_active flag. This flag wakes up the IGT compliance tool that then fills the framebuffers and triggers a modeset.
Video Pattern Tests (4.3.3.1):
It reads the DPCD registers to set the requested video pattern parameters. It then sets the test active flag that wakes up the IGT tool, userspace reads the video pattern values from corresponding debugfs files and fills the framebuffers and triggers a modeset.
Manasi Navare (4):
drm/i915: Add support for DP link training compliance drm/i915: Fixes to support DP Compliance EDID tests
drm: Add definitions for DP compliance Video pattern tests drm/i915: Add support for DP Video pattern compliance tests
drivers/gpu/drm/i915/i915_debugfs.c | 14 ++++- drivers/gpu/drm/i915/intel_dp.c | 117 ++++++++++++++++++++++++++++++++++-- drivers/gpu/drm/i915/intel_dp_mst.c | 7 ++- drivers/gpu/drm/i915/intel_drv.h | 5 ++ include/drm/drm_dp_helper.h | 58 ++++++++++++++++++ 5 files changed, 193 insertions(+), 8 deletions(-)
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 1/4 drm/i915: Add support for DP link training compliance
This patch adds support to handle automated DP compliance link training test requests. This patch has been tested with Unigraf DPR-120 DP Compliance device for testing Link Training Compliance.
After we get a short pulse Compliance test request, test request values are read and hotplug uevent is sent in order to trigger another modeset during which the pipe is configured and link is retrained and enabled for link parameters requested by the test.
v2:
* Validate the test lane count before using it inintel_dp_compute_config (Jani Nikula)
--- drivers/gpu/drm/i915/intel_dp.c | 46 ++++++++++++++++++++++++++++++++++++---- drivers/gpu/drm/i915/intel_drv.h | 2 ++ 2 files changed, 44 insertions(+), 4 deletions(-)
drivers/gpu/drm/i915/intel_dp.c +42 -4
@@ -1613,6 +1613,7 @@ static int intel_dp_compute_bpp(struct intel_dp *intel_dp,/* Conveniently, the link BW constants become indices with a shift...*/ int min_clock =0 ;int max_clock; +int link_rate_index;int bpp, mode_rate;int link_avail, link_clock;int common_rates[DP_MAX_SUPPORTED_RATES ] = {};
@@ -1654,6 +1655,17 @@ static int intel_dp_compute_bpp(struct intel_dp *intel_dp,if (adjusted_mode->flags &DRM_MODE_FLAG_DBLCLK )return false; +/* Use values requested by Compliance Test Request */ +if (intel_dp->compliance.test_type ==DP_TEST_LINK_TRAINING ) { + link_rate_index =intel_dp_link_rate_index (intel_dp, + common_rates, +drm_dp_bw_code_to_link_rate (intel_dp->compliance.test_link_rate)); +if (link_rate_index >=0 ) + min_clock = max_clock = link_rate_index; +if (min_lane_count <= intel_dp->compliance.test_lane_count + && intel_dp->compliance.test_lane_count >= max_lane_count) + min_lane_count = max_lane_count = intel_dp->compliance.test_lane_count; + } DRM_DEBUG_KMS("DP link computation with max lane count %i " "max bw %d pixel clock %iKHz\n", max_lane_count, common_rates[max_clock],
@@ -3921,6 +3933,27 @@ int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc)static uint8_t intel_dp_autotest_link_training (struct intel_dp *intel_dp) {uint8_t test_result =DP_TEST_ACK ; +int status =0 ; +/* (DP CTS 1.2) +* 4.3.1.11 +*/ +/* Read the TEST_LANE_COUNT and TEST_LINK_RTAE fields (DP CTS 3.1.4) */ + status =drm_dp_dpcd_readb (&intel_dp->aux,DP_TEST_LANE_COUNT , + &intel_dp->compliance.test_lane_count); + +if (status <=0 ) { +DRM_DEBUG_KMS ("Lane count read failed\n" ); +return 0 ; + } + intel_dp->compliance.test_lane_count &=DP_MAX_LANE_COUNT_MASK ; + + status =drm_dp_dpcd_readb (&intel_dp->aux,DP_TEST_LINK_RATE , + &intel_dp->compliance.test_link_rate); +if (status <=0 ) { +DRM_DEBUG_KMS ("Link Rate read failed\n" ); +return 0 ; + } +return test_result; }
@@ -4135,9 +4168,8 @@ static void intel_dp_handle_test_request(struct intel_dp *intel_dp)if (!intel_dp->lane_count)return ; -/* if link training is requested we should perform it always */ -if ((intel_dp->compliance.test_type ==DP_TEST_LINK_TRAINING ) || - (!drm_dp_channel_eq_ok (link_status, intel_dp->lane_count))) { +/* Retrain if Channel EQ or CR not ok */ +if (!drm_dp_channel_eq_ok (link_status, intel_dp->lane_count)) {DRM_DEBUG_KMS ("%s: channel EQ not ok, retraining\n" , intel_encoder->base.name);
@@ -4162,6 +4194,7 @@ static void intel_dp_handle_test_request(struct intel_dp *intel_dp) intel_dp_short_pulse(struct intel_dp *intel_dp) {struct drm_device *dev =intel_dp_to_dev (intel_dp); +struct intel_encoder *intel_encoder = &dp_to_dig_port (intel_dp)->base;u8 sink_irq_vector =0 ;u8 old_sink_count = intel_dp->sink_count;bool ret;
@@ -4195,7 +4228,7 @@ static void intel_dp_handle_test_request(struct intel_dp *intel_dp) sink_irq_vector);if (sink_irq_vector &DP_AUTOMATED_TEST_REQUEST ) -DRM_DEBUG_DRIVER ("Test request in short pulse not handled\n" ); +intel_dp_handle_test_request (intel_dp);if (sink_irq_vector & (DP_CP_IRQ |DP_SINK_SPECIFIC_IRQ ))DRM_DEBUG_DRIVER ("CP or sink specific irq unhandled\n" ); }
@@ -4203,6 +4236,11 @@ static void intel_dp_handle_test_request(struct intel_dp *intel_dp)drm_modeset_lock (&dev->mode_config.connection_mutex,NULL );intel_dp_check_link_status (intel_dp);drm_modeset_unlock (&dev->mode_config.connection_mutex); +if (intel_dp->compliance.test_type ==DP_TEST_LINK_TRAINING ) { +DRM_DEBUG_KMS ("Link Training Compliance Test requested\n" ); +/* Send a Hotplug Uevent to userspace to start modeset */ +drm_kms_helper_hotplug_event (intel_encoder->base.dev); + }return true; }
drivers/gpu/drm/i915/intel_drv.h +2 -0
@@ -893,6 +893,8 @@ struct intel_dp_compliance {unsigned long test_type;struct intel_dp_compliance_data test_data;bool test_active; +u8 test_link_rate; +u8 test_lane_count; };struct intel_dp {
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 1/4] drm/i915: Add support for DP link training compliance
Hi Jani,
Could you please review this patch?
I have added the lane count checking and other review comments you had. Is there anything else that is blocking from getting this patch merged?
Regards
Manasi
Quoted 137 lines · Manasi Navare
This patch adds support to handle automated DP compliance link training test requests. This patch has been tested with Unigraf DPR-120 DP Compliance device for testing Link Training Compliance.
After we get a short pulse Compliance test request, test request values are read and hotplug uevent is sent in order to trigger another modeset during which the pipe is configured and link is retrained and enabled for link parameters requested by the test.v2:
* Validate the test lane count before using it inintel_dp_compute_config(Jani Nikula)Signed-off-by Manasi Navare <[email protected]>Cc Jani Nikula <[email protected]>Cc Daniel Vetter <[email protected]>Cc Ville Syrjala <[email protected]>--- drivers/gpu/drm/i915/intel_dp.c | 46 ++++++++++++++++++++++++++++++++++++---- drivers/gpu/drm/i915/intel_drv.h | 2 ++ 2 files changed, 44 insertions(+), 4 deletions(-)drivers/gpu/drm/i915/intel_dp.c +42
-4@@ -1613,6 +1613,7 @@ static int intel_dp_compute_bpp(struct intel_dp *intel_dp,/* Conveniently, the link BW constants become indices with a shift...*/ int min_clock =0 ;int max_clock; +int link_rate_index;int bpp, mode_rate;int link_avail, link_clock;int common_rates[DP_MAX_SUPPORTED_RATES ] = {};@@ -1654,6 +1655,17 @@ static int intel_dp_compute_bpp(struct intel_dp *intel_dp,if (adjusted_mode->flags &DRM_MODE_FLAG_DBLCLK )return false; +/* Use values requested by Compliance Test Request */ +if (intel_dp->compliance.test_type ==DP_TEST_LINK_TRAINING ) { + link_rate_index =intel_dp_link_rate_index (intel_dp, + common_rates, +drm_dp_bw_code_to_link_rate (intel_dp->compliance.test_link_rate)); +if (link_rate_index >=0 ) + min_clock = max_clock = link_rate_index; +if (min_lane_count <= intel_dp->compliance.test_lane_count + && intel_dp->compliance.test_lane_count >= max_lane_count) + min_lane_count = max_lane_count = intel_dp->compliance.test_lane_count; + } DRM_DEBUG_KMS("DP link computation with max lane count %i " "max bw %d pixel clock %iKHz\n", max_lane_count, common_rates[max_clock],@@ -3921,6 +3933,27 @@ int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc)static uint8_t intel_dp_autotest_link_training (struct intel_dp *intel_dp) {uint8_t test_result =DP_TEST_ACK ; +int status =0 ; +/* (DP CTS 1.2) +* 4.3.1.11 +*/ +/* Read the TEST_LANE_COUNT and TEST_LINK_RTAE fields (DP CTS 3.1.4) */ + status =drm_dp_dpcd_readb (&intel_dp->aux,DP_TEST_LANE_COUNT , + &intel_dp->compliance.test_lane_count); + +if (status <=0 ) { +DRM_DEBUG_KMS ("Lane count read failed\n" ); +return 0 ; + } + intel_dp->compliance.test_lane_count &=DP_MAX_LANE_COUNT_MASK ; + + status =drm_dp_dpcd_readb (&intel_dp->aux,DP_TEST_LINK_RATE , + &intel_dp->compliance.test_link_rate); +if (status <=0 ) { +DRM_DEBUG_KMS ("Link Rate read failed\n" ); +return 0 ; + } +return test_result; }@@ -4135,9 +4168,8 @@ static void intel_dp_handle_test_request(struct intel_dp *intel_dp)if (!intel_dp->lane_count)return ; -/* if link training is requested we should perform it always */ -if ((intel_dp->compliance.test_type ==DP_TEST_LINK_TRAINING ) || - (!drm_dp_channel_eq_ok (link_status, intel_dp->lane_count))) { +/* Retrain if Channel EQ or CR not ok */ +if (!drm_dp_channel_eq_ok (link_status, intel_dp->lane_count)) {DRM_DEBUG_KMS ("%s: channel EQ not ok, retraining\n" , intel_encoder->base.name);@@ -4162,6 +4194,7 @@ static void intel_dp_handle_test_request(struct intel_dp *intel_dp) intel_dp_short_pulse(struct intel_dp *intel_dp) {struct drm_device *dev =intel_dp_to_dev (intel_dp); +struct intel_encoder *intel_encoder = &dp_to_dig_port (intel_dp)->base;u8 sink_irq_vector =0 ;u8 old_sink_count = intel_dp->sink_count;bool ret;@@ -4195,7 +4228,7 @@ static void intel_dp_handle_test_request(struct intel_dp *intel_dp) sink_irq_vector);if (sink_irq_vector &DP_AUTOMATED_TEST_REQUEST ) -DRM_DEBUG_DRIVER ("Test request in short pulse not handled\n" ); +intel_dp_handle_test_request (intel_dp);if (sink_irq_vector & (DP_CP_IRQ |DP_SINK_SPECIFIC_IRQ ))DRM_DEBUG_DRIVER ("CP or sink specific irq unhandled\n" ); }@@ -4203,6 +4236,11 @@ static void intel_dp_handle_test_request(struct intel_dp *intel_dp)drm_modeset_lock (&dev->mode_config.connection_mutex,NULL );intel_dp_check_link_status (intel_dp);drm_modeset_unlock (&dev->mode_config.connection_mutex); +if (intel_dp->compliance.test_type ==DP_TEST_LINK_TRAINING ) { +DRM_DEBUG_KMS ("Link Training Compliance Test requested\n" ); +/* Send a Hotplug Uevent to userspace to start modeset */ +drm_kms_helper_hotplug_event (intel_encoder->base.dev); + }return true; }drivers/gpu/drm/i915/intel_drv.h +2
-0@@ -893,6 +893,8 @@ struct intel_dp_compliance {unsigned long test_type;struct intel_dp_compliance_data test_data;bool test_active; +u8 test_link_rate; +u8 test_lane_count; };struct intel_dp {Signature · 1 line
1.9.1
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Jani Nikula
maintainerRe: [PATCH 1/4] drm/i915: Add support for DP link training compliance
In reply to Manasi NavareQuoted 39 lines · Manasi Navare
This patch adds support to handle automated DP compliance link training test requests. This patch has been tested with Unigraf DPR-120 DP Compliance device for testing Link Training Compliance.
After we get a short pulse Compliance test request, test request values are read and hotplug uevent is sent in order to trigger another modeset during which the pipe is configured and link is retrained and enabled for link parameters requested by the test.v2:
* Validate the test lane count before using it inintel_dp_compute_config(Jani Nikula)Signed-off-by Manasi Navare <[email protected]>Cc Jani Nikula <[email protected]>Cc Daniel Vetter <[email protected]>Cc Ville Syrjala <[email protected]>--- drivers/gpu/drm/i915/intel_dp.c | 46 ++++++++++++++++++++++++++++++++++++---- drivers/gpu/drm/i915/intel_drv.h | 2 ++ 2 files changed, 44 insertions(+), 4 deletions(-)drivers/gpu/drm/i915/intel_dp.c +2
-0@@ -1613,6 +1613,7 @@ static int intel_dp_compute_bpp(struct intel_dp *intel_dp,/* Conveniently, the link BW constants become indices with a shift...*/ int min_clock =0 ;int max_clock; +int link_rate_index;int bpp, mode_rate;int link_avail, link_clock;int common_rates[DP_MAX_SUPPORTED_RATES ] = {};@@ -1654,6 +1655,17 @@ static int intel_dp_compute_bpp(struct intel_dp *intel_dp,if (adjusted_mode->flags &DRM_MODE_FLAG_DBLCLK )return false; +/* Use values requested by Compliance Test Request */
drivers/gpu/drm/i915/intel_dp.c static int intel_dp_compute_bpp(struct intel_dp *intel_dp, · line 1668
Quoted 10 lines
drivers/gpu/drm/i915/intel_dp.c +10
-0+if (intel_dp->compliance.test_type ==DP_TEST_LINK_TRAINING ) { + link_rate_index =intel_dp_link_rate_index (intel_dp, + common_rates, +drm_dp_bw_code_to_link_rate (intel_dp->compliance.test_link_rate)); +if (link_rate_index >=0 ) + min_clock = max_clock = link_rate_index; +if (min_lane_count <= intel_dp->compliance.test_lane_count + && intel_dp->compliance.test_lane_count >= max_lane_count) + min_lane_count = max_lane_count = intel_dp->compliance.test_lane_count; + }
Why don't we do these checks and conversions when we get the test request, so we can NAK the request on errors?
Quoted 8 lines
drivers/gpu/drm/i915/intel_dp.c +1
-0DRM_DEBUG_KMS("DP link computation with max lane count %i " "max bw %d pixel clock %iKHz\n", max_lane_count, common_rates[max_clock],@@ -3921,6 +3933,27 @@ int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc)static uint8_t intel_dp_autotest_link_training (struct intel_dp *intel_dp) {uint8_t test_result =DP_TEST_ACK ; +int status =0 ;
drivers/gpu/drm/i915/intel_dp.c int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc) · line 3946
Quoted 10 lines
drivers/gpu/drm/i915/intel_dp.c +10
-0+/* (DP CTS 1.2) +* 4.3.1.11 +*/ +/* Read the TEST_LANE_COUNT and TEST_LINK_RTAE fields (DP CTS 3.1.4) */ + status =drm_dp_dpcd_readb (&intel_dp->aux,DP_TEST_LANE_COUNT , + &intel_dp->compliance.test_lane_count); + +if (status <=0 ) { +DRM_DEBUG_KMS ("Lane count read failed\n" ); +return 0 ;
return DP_TEST_NAK;
drivers/gpu/drm/i915/intel_dp.c int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc) · line 3954
Quoted 8 lines
drivers/gpu/drm/i915/intel_dp.c +8
-0+ } + intel_dp->compliance.test_lane_count &=DP_MAX_LANE_COUNT_MASK ; + + status =drm_dp_dpcd_readb (&intel_dp->aux,DP_TEST_LINK_RATE , + &intel_dp->compliance.test_link_rate); +if (status <=0 ) { +DRM_DEBUG_KMS ("Link Rate read failed\n" ); +return 0 ;
return DP_TEST_NAK;
drivers/gpu/drm/i915/intel_dp.c int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc) · line 3957
Quoted 3 lines
drivers/gpu/drm/i915/intel_dp.c +2
-0+ } +return test_result;
Could replace this with a direct return DP_TEST_ACK without the temp variable.
Quoted 56 lines
drivers/gpu/drm/i915/intel_dp.c +9
-4}@@ -4135,9 +4168,8 @@ static void intel_dp_handle_test_request(struct intel_dp *intel_dp)if (!intel_dp->lane_count)return ; -/* if link training is requested we should perform it always */ -if ((intel_dp->compliance.test_type ==DP_TEST_LINK_TRAINING ) || - (!drm_dp_channel_eq_ok (link_status, intel_dp->lane_count))) { +/* Retrain if Channel EQ or CR not ok */ +if (!drm_dp_channel_eq_ok (link_status, intel_dp->lane_count)) {DRM_DEBUG_KMS ("%s: channel EQ not ok, retraining\n" , intel_encoder->base.name);@@ -4162,6 +4194,7 @@ static void intel_dp_handle_test_request(struct intel_dp *intel_dp) intel_dp_short_pulse(struct intel_dp *intel_dp) {struct drm_device *dev =intel_dp_to_dev (intel_dp); +struct intel_encoder *intel_encoder = &dp_to_dig_port (intel_dp)->base;u8 sink_irq_vector =0 ;u8 old_sink_count = intel_dp->sink_count;bool ret;@@ -4195,7 +4228,7 @@ static void intel_dp_handle_test_request(struct intel_dp *intel_dp) sink_irq_vector);if (sink_irq_vector &DP_AUTOMATED_TEST_REQUEST ) -DRM_DEBUG_DRIVER ("Test request in short pulse not handled\n" ); +intel_dp_handle_test_request (intel_dp);if (sink_irq_vector & (DP_CP_IRQ |DP_SINK_SPECIFIC_IRQ ))DRM_DEBUG_DRIVER ("CP or sink specific irq unhandled\n" ); }@@ -4203,6 +4236,11 @@ static void intel_dp_handle_test_request(struct intel_dp *intel_dp)drm_modeset_lock (&dev->mode_config.connection_mutex,NULL );intel_dp_check_link_status (intel_dp);drm_modeset_unlock (&dev->mode_config.connection_mutex); +if (intel_dp->compliance.test_type ==DP_TEST_LINK_TRAINING ) { +DRM_DEBUG_KMS ("Link Training Compliance Test requested\n" ); +/* Send a Hotplug Uevent to userspace to start modeset */ +drm_kms_helper_hotplug_event (intel_encoder->base.dev); + }return true; }drivers/gpu/drm/i915/intel_drv.h +2
-0@@ -893,6 +893,8 @@ struct intel_dp_compliance {unsigned long test_type;struct intel_dp_compliance_data test_data;bool test_active; +u8 test_link_rate; +u8 test_lane_count; };struct intel_dp {
Signature · 5 lines
Jani Nikula, Intel Open Source Technology Center _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 2/4 drm/i915: Fixes to support DP Compliance EDID tests
In reply to Manasi NavareThis patch addresses a few issues from the original patch for DP Compliance EDID test support submitted by
Todd Previte<[email protected]>
Video Mode requested in the EDID test handler for the EDID Read test (CTS 4.2.2.3) should be set to PREFERRED as per the CTS spec.
v2:
* Added read debugfs data from test_data.edid if its EDID test (Jani NIkula)
--- drivers/gpu/drm/i915/i915_debugfs.c | 5 ++++- drivers/gpu/drm/i915/intel_dp.c | 4 ++-- 2 files changed, 6 insertions(+), 3 deletions(-)
drivers/gpu/drm/i915/i915_debugfs.c +4 -1
@@ -3737,7 +3737,10 @@ static int i915_displayport_test_data_show(struct seq_file *m, void *data)if (connector->status == connector_status_connected && connector->encoder !=NULL ) { intel_dp =enc_to_intel_dp (connector->encoder); -seq_printf (m,"%lx" , intel_dp->compliance.test_data.edid); +if (intel_dp->compliance.test_type == +DP_TEST_LINK_EDID_READ ) +seq_printf (m,"%lx" , + intel_dp->compliance.test_data.edid); }else seq_puts (m,"0" ); }
drivers/gpu/drm/i915/intel_dp.c +2 -2
@@ -3965,7 +3965,7 @@ static uint8_t intel_dp_autotest_video_pattern(struct intel_dp *intel_dp)static uint8_t intel_dp_autotest_edid (struct intel_dp *intel_dp) { -uint8_t test_result =DP_TEST_NAK ; +uint8_t test_result =DP_TEST_ACK ;struct intel_connector *intel_connector = intel_dp->attached_connector;struct drm_connector *connector = &intel_connector->base;
@@ -4000,7 +4000,7 @@ static uint8_t intel_dp_autotest_edid(struct intel_dp *intel_dp)DRM_DEBUG_KMS ("Failed to write EDID checksum\n" ); test_result =DP_TEST_ACK |DP_TEST_EDID_CHECKSUM_WRITE ; - intel_dp->compliance.test_data.edid =INTEL_DP_RESOLUTION_STANDARD ; + intel_dp->compliance.test_data.edid =INTEL_DP_RESOLUTION_PREFERRED ; }/* Set test active flag here so userspace doesn't interrupt things */
Signature · 6 lines
1.9.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH 2/4] drm/i915: Fixes to support DP Compliance EDID tests
Hi Jani,
This is another simple patch that only changed EDID test to PREFERRED vs STANDARD as per the CTS spec. Is there anything else that is blocking this patch getting merged?
Regards
Manasi
Quoted 59 lines · Manasi Navare
This patch addresses a few issues from the original patch for DP Compliance EDID test support submitted by
Todd Previte<[email protected]>Video Mode requested in the EDID test handler for the EDID Read test (CTS 4.2.2.3) should be set to PREFERRED as per the CTS spec.
v2:
* Added read debugfs data from test_data.edid if its EDID test (Jani NIkula)Signed-off-by Manasi Navare <[email protected]>Cc Jani Nikula <[email protected]>Cc Daniel Vetter <[email protected]>Cc Ville Syrjala <[email protected]>--- drivers/gpu/drm/i915/i915_debugfs.c | 5 ++++- drivers/gpu/drm/i915/intel_dp.c | 4 ++-- 2 files changed, 6 insertions(+), 3 deletions(-)drivers/gpu/drm/i915/i915_debugfs.c +4
-1@@ -3737,7 +3737,10 @@ static int i915_displayport_test_data_show(struct seq_file *m, void *data)if (connector->status == connector_status_connected && connector->encoder !=NULL ) { intel_dp =enc_to_intel_dp (connector->encoder); -seq_printf (m,"%lx" , intel_dp->compliance.test_data.edid); +if (intel_dp->compliance.test_type == +DP_TEST_LINK_EDID_READ ) +seq_printf (m,"%lx" , + intel_dp->compliance.test_data.edid); }else seq_puts (m,"0" ); }drivers/gpu/drm/i915/intel_dp.c +2
-2@@ -3965,7 +3965,7 @@ static uint8_t intel_dp_autotest_video_pattern(struct intel_dp *intel_dp)static uint8_t intel_dp_autotest_edid (struct intel_dp *intel_dp) { -uint8_t test_result =DP_TEST_NAK ; +uint8_t test_result =DP_TEST_ACK ;struct intel_connector *intel_connector = intel_dp->attached_connector;struct drm_connector *connector = &intel_connector->base;@@ -4000,7 +4000,7 @@ static uint8_t intel_dp_autotest_edid(struct intel_dp *intel_dp)DRM_DEBUG_KMS ("Failed to write EDID checksum\n" ); test_result =DP_TEST_ACK |DP_TEST_EDID_CHECKSUM_WRITE ; - intel_dp->compliance.test_data.edid =INTEL_DP_RESOLUTION_STANDARD ; + intel_dp->compliance.test_data.edid =INTEL_DP_RESOLUTION_PREFERRED ; }/* Set test active flag here so userspace doesn't interrupt things */ Signature · 1 line
1.9.1
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH 3/4 drm: Add definitions for DP compliance Video pattern tests
In reply to Manasi Navarev2:
* Add all the other DP Complianec TEST register defs (Jani Nikula)
--- include/drm/drm_dp_helper.h | 58 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 58 insertions(+)
include/drm/drm_dp_helper.h +58 -0
@@ -417,6 +417,64 @@#define DP_TEST_LANE_COUNT 0x220#define DP_TEST_PATTERN 0x221 +# define DP_NO_TEST_PATTERN (0x0) +# define DP_COLOR_RAMP (0x1) +# define DP_BLACK_AND_WHITE_VERTICAL_LINES (0x2) +# define DP_COLOR_SQUARE (0x3) + +#define DP_TEST_H_TOTAL_HI 0x222 +#define DP_TEST_H_TOTAl_LO 0x223 + +#define DP_TEST_V_TOTAL_HI 0x224 +#define DP_TEST_V_TOTAl_LO 0x225 + +#define DP_TEST_H_START_HI 0x226 +#define DP_TEST_H_START_LO 0x227 + +#define DP_TEST_V_START_HI 0x228 +#define DP_TEST_V_START_LO 0x229 + +#define DP_TEST_HSYNC_HI 0x22A +#define DP_TEST_HSYNC_LO 0x22B + +#define DP_TEST_VSYNC_HI 0x22C +#define DP_TEST_VSYNC_LO 0x22D + +#define DP_TEST_H_WIDTH_HI 0x22E +#define DP_TESt_H_WIDTH_LO 0x22F + +#define DP_TEST_V_HEIGHT_HI 0x230 +#define DP_TEST_V_HEIGHT_LO 0x231 + +#define DP_TEST_MISC_LO 0x232 +# define DP_TEST_SYNC_CLOCK_MASK (1 << 0) +# define DP_CLOCK_ASYNC (0x0) +# define DP_CLOCK_SYNC (0x1) +# define DP_TEST_COLOR_FORMAT_MASK (3 << 1) +# define DP_TEST_COLOR_FORMAT_SHIFT 1 +# define DP_COLOR_FORMAT_RGB (0x0) +# define DP_COLOR_FORMAT_YCbCr422 (0x1) +# define DP_COLOR_FORMAT_YCbCr444 (0x2) +# define DP_TEST_DYNAMIC_RANGE_MASK (1 << 3) +# define DP_TEST_DYNAMIC_RANGE_SHIFT 3 +# define DP_VESA_RANGE (0x0) +# define DP_CEA_RANGE (0x1) +# define DP_TEST_BIT_DEPTH_MASK (7 << 5) +# define DP_TEST_BIT_DEPTH_SHIFT 5 +# define DP_TEST_BIT_DEPTH_6 (0x0) +# define DP_TEST_BIT_DEPTH_8 (0x1) +# define DP_TEST_BIT_DEPTH_10 (0x2) +# define DP_TEST_BIT_DEPTH_12 (0x3) +# define DP_TEST_BIT_DEPTH_16 (0x4) +#define DP_TEST_MISC_HI 0x233 +# define DP_TEST_REFRESH_DENOMINATOR_MASK (1 << 0) +# define REFRESH_DENOMINATOR_1 (0x0) +# define REFRESH_DENOMINATOR_1_001 (0x1) +# define DP_TEST_INTERLACED_MASK (1 << 1) +# define DP_NON_INTERLACED (0x0) +# define DP_INTERLACED (0x1) + +#define DP_TEST_REFRESH_RATE_NUMERATOR 0x234#define DP_TEST_CRC_R_CR 0x240#define DP_TEST_CRC_G_Y 0x242
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 3/4] drm: Add definitions for DP compliance Video pattern tests
Hi Jani,
I have added all the video pattern definitions from CTS
spec following the definition conventions used around this file.
This addresses all the review comments from you, is there anything else that is blocking this patch from getting merged? Could you please review this patch?
Regards
Manasi
Quoted 83 lines · Manasi Navare
v2:
* Add all the other DP Complianec TEST register defs (Jani Nikula)Cc Jani Nikula <[email protected]>Cc Daniel Vetter <[email protected]>Cc Ville Syrjala <[email protected]>Signed-off-by Manasi Navare <[email protected]>--- include/drm/drm_dp_helper.h | 58 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 58 insertions(+)include/drm/drm_dp_helper.h +58
-0@@ -417,6 +417,64 @@#define DP_TEST_LANE_COUNT 0x220#define DP_TEST_PATTERN 0x221 +# define DP_NO_TEST_PATTERN (0x0) +# define DP_COLOR_RAMP (0x1) +# define DP_BLACK_AND_WHITE_VERTICAL_LINES (0x2) +# define DP_COLOR_SQUARE (0x3) + +#define DP_TEST_H_TOTAL_HI 0x222 +#define DP_TEST_H_TOTAl_LO 0x223 + +#define DP_TEST_V_TOTAL_HI 0x224 +#define DP_TEST_V_TOTAl_LO 0x225 + +#define DP_TEST_H_START_HI 0x226 +#define DP_TEST_H_START_LO 0x227 + +#define DP_TEST_V_START_HI 0x228 +#define DP_TEST_V_START_LO 0x229 + +#define DP_TEST_HSYNC_HI 0x22A +#define DP_TEST_HSYNC_LO 0x22B + +#define DP_TEST_VSYNC_HI 0x22C +#define DP_TEST_VSYNC_LO 0x22D + +#define DP_TEST_H_WIDTH_HI 0x22E +#define DP_TESt_H_WIDTH_LO 0x22F + +#define DP_TEST_V_HEIGHT_HI 0x230 +#define DP_TEST_V_HEIGHT_LO 0x231 + +#define DP_TEST_MISC_LO 0x232 +# define DP_TEST_SYNC_CLOCK_MASK (1 << 0) +# define DP_CLOCK_ASYNC (0x0) +# define DP_CLOCK_SYNC (0x1) +# define DP_TEST_COLOR_FORMAT_MASK (3 << 1) +# define DP_TEST_COLOR_FORMAT_SHIFT 1 +# define DP_COLOR_FORMAT_RGB (0x0) +# define DP_COLOR_FORMAT_YCbCr422 (0x1) +# define DP_COLOR_FORMAT_YCbCr444 (0x2) +# define DP_TEST_DYNAMIC_RANGE_MASK (1 << 3) +# define DP_TEST_DYNAMIC_RANGE_SHIFT 3 +# define DP_VESA_RANGE (0x0) +# define DP_CEA_RANGE (0x1) +# define DP_TEST_BIT_DEPTH_MASK (7 << 5) +# define DP_TEST_BIT_DEPTH_SHIFT 5 +# define DP_TEST_BIT_DEPTH_6 (0x0) +# define DP_TEST_BIT_DEPTH_8 (0x1) +# define DP_TEST_BIT_DEPTH_10 (0x2) +# define DP_TEST_BIT_DEPTH_12 (0x3) +# define DP_TEST_BIT_DEPTH_16 (0x4) +#define DP_TEST_MISC_HI 0x233 +# define DP_TEST_REFRESH_DENOMINATOR_MASK (1 << 0) +# define REFRESH_DENOMINATOR_1 (0x0) +# define REFRESH_DENOMINATOR_1_001 (0x1) +# define DP_TEST_INTERLACED_MASK (1 << 1) +# define DP_NON_INTERLACED (0x0) +# define DP_INTERLACED (0x1) + +#define DP_TEST_REFRESH_RATE_NUMERATOR 0x234#define DP_TEST_CRC_R_CR 0x240#define DP_TEST_CRC_G_Y 0x242Signature · 1 line
1.9.1
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Jani Nikula
maintainerRe: [PATCH 3/4] drm: Add definitions for DP compliance Video pattern tests
In reply to Manasi NavareQuoted 16 lines · Manasi Navare
v2:
* Add all the other DP Complianec TEST register defs (Jani Nikula)Cc Jani Nikula <[email protected]>Cc Daniel Vetter <[email protected]>Cc Ville Syrjala <[email protected]>Signed-off-by Manasi Navare <[email protected]>--- include/drm/drm_dp_helper.h | 58 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 58 insertions(+)include/drm/drm_dp_helper.h +0
-0
include/drm/drm_dp_helper.h line 423
Quoted 7 lines
include/drm/drm_dp_helper.h +4
-0@@ -417,6 +417,64 @@#define DP_TEST_LANE_COUNT 0x220#define DP_TEST_PATTERN 0x221 +# define DP_NO_TEST_PATTERN (0x0) +# define DP_COLOR_RAMP (0x1) +# define DP_BLACK_AND_WHITE_VERTICAL_LINES (0x2) +# define DP_COLOR_SQUARE (0x3)
The braces are unnecessary.
Quoted 4 lines
include/drm/drm_dp_helper.h +4
-0+ +#define DP_TEST_H_TOTAL_HI 0x222 +#define DP_TEST_H_TOTAl_LO 0x223 +
include/drm/drm_dp_helper.h line 437
Quoted 10 lines
include/drm/drm_dp_helper.h +10
-0+#define DP_TEST_V_TOTAL_HI 0x224 +#define DP_TEST_V_TOTAl_LO 0x225 + +#define DP_TEST_H_START_HI 0x226 +#define DP_TEST_H_START_LO 0x227 + +#define DP_TEST_V_START_HI 0x228 +#define DP_TEST_V_START_LO 0x229 + +#define DP_TEST_HSYNC_HI 0x22A
You should add bit definitions for this, as bit 7 is polarity, and only bits 6:0 are the hsync high order bits.
include/drm/drm_dp_helper.h line 440
Quoted 3 lines
include/drm/drm_dp_helper.h +3
-0+#define DP_TEST_HSYNC_LO 0x22B + +#define DP_TEST_VSYNC_HI 0x22C
Same as DP_TEST_HSYNC_HI.
include/drm/drm_dp_helper.h line 444
Quoted 4 lines
include/drm/drm_dp_helper.h +4
-0+#define DP_TEST_VSYNC_LO 0x22D + +#define DP_TEST_H_WIDTH_HI 0x22E +#define DP_TESt_H_WIDTH_LO 0x22F
^ should be T
include/drm/drm_dp_helper.h line 449
Quoted 5 lines
include/drm/drm_dp_helper.h +5
-0+ +#define DP_TEST_V_HEIGHT_HI 0x230 +#define DP_TEST_V_HEIGHT_LO 0x231 + +#define DP_TEST_MISC_LO 0x232
The other definitions have HI and LO because they contain a 15- or 16-bit value spread across two offsets. This is not the case here. I'd call these DP_TEST_MISC0 and DP_TEST_MISC1.
include/drm/drm_dp_helper.h line 452
Quoted 3 lines
include/drm/drm_dp_helper.h +3
-0+# define DP_TEST_SYNC_CLOCK_MASK (1 << 0) +# define DP_CLOCK_ASYNC (0x0) +# define DP_CLOCK_SYNC (0x1)
Single-bit values should just be TEST_SYNCHRONOUS_CLOCK (1 << 0). No masks, shifts or values.
include/drm/drm_dp_helper.h line 457
Quoted 5 lines
include/drm/drm_dp_helper.h +5
-0+# define DP_TEST_COLOR_FORMAT_MASK (3 << 1) +# define DP_TEST_COLOR_FORMAT_SHIFT 1 +# define DP_COLOR_FORMAT_RGB (0x0) +# define DP_COLOR_FORMAT_YCbCr422 (0x1) +# define DP_COLOR_FORMAT_YCbCr444 (0x2)
The values should be shifted to the right position, e.g. DP_COLOR_FORMAT_RGB (0 << 1). The usage pattern would be:
if ((x & DP_TEST_COLOR_FORMAT_MASK) == DP_COLOR_FORMAT_RGB)
or
x &= ~DP_TEST_COLOR_FORMAT_MASK;
x |= DP_COLOR_FORMAT_YCbCr422;include/drm/drm_dp_helper.h line 459
Quoted 2 lines
include/drm/drm_dp_helper.h +2
-0+# define DP_TEST_DYNAMIC_RANGE_MASK (1 << 3) +# define DP_TEST_DYNAMIC_RANGE_SHIFT 3
Single-bit values should just be DP_TEST_DYNAMIC_RANGE (1 << 3).
Same for all of the defines below.
BR,
Jani.
Quoted 21 lines
include/drm/drm_dp_helper.h +18
-0+# define DP_VESA_RANGE (0x0) +# define DP_CEA_RANGE (0x1) +# define DP_TEST_BIT_DEPTH_MASK (7 << 5) +# define DP_TEST_BIT_DEPTH_SHIFT 5 +# define DP_TEST_BIT_DEPTH_6 (0x0) +# define DP_TEST_BIT_DEPTH_8 (0x1) +# define DP_TEST_BIT_DEPTH_10 (0x2) +# define DP_TEST_BIT_DEPTH_12 (0x3) +# define DP_TEST_BIT_DEPTH_16 (0x4) +#define DP_TEST_MISC_HI 0x233 +# define DP_TEST_REFRESH_DENOMINATOR_MASK (1 << 0) +# define REFRESH_DENOMINATOR_1 (0x0) +# define REFRESH_DENOMINATOR_1_001 (0x1) +# define DP_TEST_INTERLACED_MASK (1 << 1) +# define DP_NON_INTERLACED (0x0) +# define DP_INTERLACED (0x1) + +#define DP_TEST_REFRESH_RATE_NUMERATOR 0x234#define DP_TEST_CRC_R_CR 0x240#define DP_TEST_CRC_G_Y 0x242
Signature · 5 lines
Jani Nikula, Intel Open Source Technology Center _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 4/4 drm/i915: Add support for DP Video pattern compliance tests
In reply to Manasi NavareThe intel_dp_autotest_video_pattern() function gets invoked through the compliance test handler on a HPD short pulse if the test type is set to DP_TEST_VIDEO_PATTERN. This performs the DPCD registers reads to read the requested test pattern, video pattern resolution, frame rate and bits per color value. The results of this analysis are handed off to userspace so that the userspace app can set the video pattern mode appropriately for the test result/response. When the test is requested with specific BPC value, we read the BPC value from the DPCD register. If this BPC value in intel_dp structure has a non-zero value and we're on a display port connector, then we use the value to calculate the bpp for the pipe.
The compliance_test_active flag is set at the end of the individual test handling functions. This is so that the kernel-side operations can be completed without the risk of interruption from the userspace app that is polling on that flag.
v2:
* Updated the DPCD Register reads based on proper defines in header (Jani Nikula)
* Squahsed the patch that forced the pipe bpp to compliance test bpp (Jani Nikula)
--- drivers/gpu/drm/i915/i915_debugfs.c | 9 +++++ drivers/gpu/drm/i915/intel_dp.c | 67 +++++++++++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_dp_mst.c | 7 +++- drivers/gpu/drm/i915/intel_drv.h | 3 ++ 4 files changed, 85 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/i915_debugfs.c +9 -0
@@ -3741,6 +3741,15 @@ static int i915_displayport_test_data_show(struct seq_file *m, void *data) DP_TEST_LINK_EDID_READ) seq_printf(m, "%lx", intel_dp->compliance.test_data.edid); + else if (intel_dp->compliance.test_type == +DP_TEST_LINK_VIDEO_PATTERN ) { +seq_printf (m,"hdisplay: %d\n" , + intel_dp->compliance.test_data.hdisplay); +seq_printf (m,"vdisplay: %d\n" , + intel_dp->compliance.test_data.vdisplay); +seq_printf (m,"bpc: %u\n" , + intel_dp->compliance.test_data.bpc); + } }else seq_puts (m,"0" ); }
drivers/gpu/drm/i915/intel_dp.c +67 -0
87 lines not on this page · raw message
drivers/gpu/drm/i915/intel_dp_mst.c +6 -1
@@ -47,6 +47,11 @@ static bool intel_dp_mst_compute_config(struct intel_encoder *encoder, pipe_config->has_pch_encoder = false; bpp =24 ; +if (intel_dp->compliance.test_data.bpc) { + bpp = intel_dp->compliance.test_data.bpc *3 ; +DRM_DEBUG_KMS ("Setting pipe bpp to %d\n" , + bpp); + }/* * for MST we always configure max link bw - the spec doesn't * seem to suggest we should do otherwise.
@@ -55,7 +60,7 @@ static bool intel_dp_mst_compute_config(struct intel_encoder *encoder, pipe_config->lane_count = lane_count; - pipe_config->pipe_bpp =24 ; + pipe_config->pipe_bpp = bpp; pipe_config->port_clock =intel_dp_max_link_rate (intel_dp); state = pipe_config->base.state;
drivers/gpu/drm/i915/intel_drv.h +3 -0
@@ -887,6 +887,9 @@ struct intel_dp_desc {struct intel_dp_compliance_data {unsigned long edid; +uint8_t video_pattern; +uint16_t hdisplay, vdisplay; +uint8_t bpc; };struct intel_dp_compliance {
Signature · 6 lines
1.9.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH 4/4] drm/i915: Add support for DP Video pattern compliance tests
Hi Jani,
Could you please review this patch? All your previous review comments are addressed. Is there anything else that is blocking this patch from getting merged?
Regards
Manasi
Quoted 187 lines · Manasi Navare
The
intel_dp_autotest_video_pattern()function gets invoked through the compliance test handler on a HPD short pulse if the test type is set toDP_TEST_VIDEO_PATTERN. This performs the DPCD registers reads to read the requested test pattern, video pattern resolution, frame rate and bits per color value. The results of this analysis are handed off to userspace so that the userspace app can set the video pattern mode appropriately for the test result/response. When the test is requested with specific BPC value, we read the BPC value from the DPCD register. If this BPC value inintel_dpstructure has a non-zero value and we're on a display port connector, then we use the value to calculate the bpp for the pipe.The
compliance_test_activeflag is set at the end of the individual test handling functions. This is so that the kernel-side operations can be completed without the risk of interruption from the userspace app that is polling on that flag.v2:
* Updated the DPCD Register reads based on proper defines in header (Jani Nikula)
* Squahsed the patch that forced the pipe bpp to compliance test bpp (Jani Nikula)Signed-off-by Manasi Navare <[email protected]>Cc Jani Nikula <[email protected]>Cc Daniel Vetter <[email protected]>Cc Ville Syrjala <[email protected]>--- drivers/gpu/drm/i915/i915_debugfs.c | 9 +++++ drivers/gpu/drm/i915/intel_dp.c | 67 +++++++++++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_dp_mst.c | 7 +++- drivers/gpu/drm/i915/intel_drv.h | 3 ++ 4 files changed, 85 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/i915_debugfs.c +9
-0@@ -3741,6 +3741,15 @@ static int i915_displayport_test_data_show(struct seq_file *m, void *data) DP_TEST_LINK_EDID_READ) seq_printf(m, "%lx", intel_dp->compliance.test_data.edid); + else if (intel_dp->compliance.test_type == +DP_TEST_LINK_VIDEO_PATTERN ) { +seq_printf (m,"hdisplay: %d\n" , + intel_dp->compliance.test_data.hdisplay); +seq_printf (m,"vdisplay: %d\n" , + intel_dp->compliance.test_data.vdisplay); +seq_printf (m,"bpc: %u\n" , + intel_dp->compliance.test_data.bpc); + } }else seq_puts (m,"0" ); }drivers/gpu/drm/i915/intel_dp.c +67
-0@@ -28,8 +28,10 @@#include <linux/i2c.h> #include <linux/slab.h> #include <linux/export.h> +#include <linux/types.h> #include <linux/notifier.h> #include <linux/reboot.h> +#include <asm/byteorder.h> #include <drm/drmP.h> #include <drm/drm_atomic_helper.h> #include <drm/drm_crtc.h> @@ -1593,6 +1595,12 @@ static int intel_dp_compute_bpp(struct intel_dp *intel_dp,if (bpc >0 ) bpp =min (bpp,3 *bpc); +/* For DP Compliance we override the computed bpp for the pipe */ +if (intel_dp->compliance.test_data.bpc !=0 ) { + pipe_config->pipe_bpp =3 *intel_dp->compliance.test_data.bpc; +DRM_DEBUG_KMS ("Setting pipe_bpp to %d\n" , + pipe_config->pipe_bpp); + }return bpp; }@@ -3960,6 +3968,65 @@ static uint8_t intel_dp_autotest_link_training(struct intel_dp *intel_dp)static uint8_t intel_dp_autotest_video_pattern (struct intel_dp *intel_dp) {uint8_t test_result =DP_TEST_NAK ; +uint8_t test_pattern; +uint16_t test_misc; +__be16 h_width, v_height; +int status =0 ; + +/* Read the TEST_PATTERN (DP CTS 3.1.5) */ + status =drm_dp_dpcd_read (&intel_dp->aux,DP_TEST_PATTERN , + &test_pattern,1 ); +if (status <=0 ) { +DRM_DEBUG_KMS ("Test pattern read failed\n" ); +return 0 ; + } +if (test_pattern !=DP_COLOR_RAMP ) +return test_result; + intel_dp->compliance.test_data.video_pattern = test_pattern; + + status =drm_dp_dpcd_read (&intel_dp->aux,DP_TEST_H_WIDTH_HI , + &h_width,2 ); +if (status <=0 ) { +DRM_DEBUG_KMS ("H Width read failed\n" ); +return 0 ; + } + intel_dp->compliance.test_data.hdisplay =be16_to_cpu (h_width); + + status =drm_dp_dpcd_read (&intel_dp->aux,DP_TEST_V_HEIGHT_HI , + &v_height,2 ); +if (status <=0 ) { +DRM_DEBUG_KMS ("V Height read failed\n" ); +return 0 ; + } + intel_dp->compliance.test_data.vdisplay =be16_to_cpu (v_height); + + status =drm_dp_dpcd_read (&intel_dp->aux,DP_TEST_MISC_LO , + &test_misc,1 ); +if (status <=0 ) { +DRM_DEBUG_KMS ("TEST MISC read failed\n" ); +return 0 ; + } +if (((test_misc &DP_TEST_COLOR_FORMAT_MASK ) >>DP_TEST_COLOR_FORMAT_SHIFT ) != +DP_COLOR_FORMAT_RGB ) +return test_result; +if (((test_misc &DP_TEST_DYNAMIC_RANGE_MASK ) >>DP_TEST_DYNAMIC_RANGE_SHIFT ) != +DP_VESA_RANGE ) +return test_result; +switch ((test_misc &DP_TEST_BIT_DEPTH_MASK ) >>DP_TEST_BIT_DEPTH_SHIFT ) { +case DP_TEST_BIT_DEPTH_6 : + intel_dp->compliance.test_data.bpc =6 ; +break ; +case DP_TEST_BIT_DEPTH_8 : + intel_dp->compliance.test_data.bpc =8 ; +break ; +default : +return test_result; + } +/* Set test active flag here so userspace doesn't interrupt things */ + intel_dp->compliance.test_active =1 ; + + test_result =DP_TEST_ACK ; +return test_result; }drivers/gpu/drm/i915/intel_dp_mst.c +6
-1@@ -47,6 +47,11 @@ static bool intel_dp_mst_compute_config(struct intel_encoder *encoder, pipe_config->has_pch_encoder = false; bpp =24 ; +if (intel_dp->compliance.test_data.bpc) { + bpp = intel_dp->compliance.test_data.bpc *3 ; +DRM_DEBUG_KMS ("Setting pipe bpp to %d\n" , + bpp); + }/* * for MST we always configure max link bw - the spec doesn't * seem to suggest we should do otherwise. @@ -55,7 +60,7 @@ static bool intel_dp_mst_compute_config(struct intel_encoder *encoder, pipe_config->lane_count = lane_count; - pipe_config->pipe_bpp =24 ; + pipe_config->pipe_bpp = bpp; pipe_config->port_clock =intel_dp_max_link_rate (intel_dp); state = pipe_config->base.state;drivers/gpu/drm/i915/intel_drv.h +3
-0@@ -887,6 +887,9 @@ struct intel_dp_desc {struct intel_dp_compliance_data {unsigned long edid; +uint8_t video_pattern; +uint16_t hdisplay, vdisplay; +uint8_t bpc; };struct intel_dp_compliance {Signature · 1 line
1.9.1
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.BAT: success for Add Automation Support for DP Compliance Testing (Rev 4)
In reply to Manasi Navare== Series Details ==
== Series Details ==
Series: Add Automation Support for DP Compliance Testing (Rev 4)
URL : https://patchwork.freedesktop.org/series/18150/
State : success
== Summary ==
Series 18150v1 Add Automation Support for DP Compliance Testing (Rev 4)
https://patchwork.freedesktop.org/api/1.0/series/18150/revisions/1/mbox/
fi-bdw-5557u total:246 pass:232 dwarn:0 dfail:0 fail:0 skip:14 fi-bsw-n3050 total:246 pass:207 dwarn:0 dfail:0 fail:0 skip:39 fi-bxt-j4205 total:246 pass:224 dwarn:0 dfail:0 fail:0 skip:22 fi-bxt-t5700 total:82 pass:69 dwarn:0 dfail:0 fail:0 skip:12 fi-byt-j1900 total:246 pass:219 dwarn:0 dfail:0 fail:0 skip:27 fi-byt-n2820 total:246 pass:215 dwarn:0 dfail:0 fail:0 skip:31 fi-hsw-4770 total:246 pass:227 dwarn:0 dfail:0 fail:0 skip:19 fi-hsw-4770r total:246 pass:227 dwarn:0 dfail:0 fail:0 skip:19 fi-ivb-3520m total:246 pass:225 dwarn:0 dfail:0 fail:0 skip:21 fi-ivb-3770 total:246 pass:225 dwarn:0 dfail:0 fail:0 skip:21 fi-kbl-7500u total:246 pass:225 dwarn:0 dfail:0 fail:0 skip:21 fi-skl-6260u total:246 pass:233 dwarn:0 dfail:0 fail:0 skip:13 fi-skl-6700hq total:246 pass:226 dwarn:0 dfail:0 fail:0 skip:20 fi-skl-6700k total:246 pass:222 dwarn:3 dfail:0 fail:0 skip:21 fi-skl-6770hq total:246 pass:233 dwarn:0 dfail:0 fail:0 skip:13 fi-snb-2520m total:246 pass:215 dwarn:0 dfail:0 fail:0 skip:31 fi-snb-2600 total:246 pass:214 dwarn:0 dfail:0 fail:0 skip:32
d4ca2d2b591f1ca6b50eaf3253412f4c11ec1be2 drm-tip: 2017y-01m-17d-22h-19m-37s UTC integration manifest 864a751 drm/i915: Add support for DP Video pattern compliance tests
09ea7ca drm: Add definitions for DP compliance Video pattern tests
df5d4dc drm/i915: Fixes to support DP Compliance EDID tests
3700c85 drm/i915: Add support for DP link training compliance
== Logs ==
For more details see: https://intel-gfx-ci.01.org/CI/Patchwork_3534/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx