irqchip: qcom: Add IRQ combiner driver
Subsystems (5)
v11 cover irqchip: qcom: Add IRQ combiner driver
Add support for IRQ combiners in the Top-level Control and Status Registers (TCSR) hardware block in Qualcomm Technologies chips.
The first patch prevents the ACPI core from attempting to map IRQ resources with a valid ResourceSource as GSIs.
The second patch adds support for ResourceSource/IRQ domain mapping and fixes IRQ probe deferral by allowing platform_device IRQ resources to be re-initialized from the corresponding ACPI IRQ resource.
Both changes described above are conditional on the ACPI_GENERIC_GSI config.
The third patch takes advantage of the new capabilities to implement the driver for the IRQ combiners.
Tested on top of v4.10-rc4.
Changes V10 -> V11:
* Add probe table and use it to implement driver presence detection.
* Fix kernel doc formatting in drivers/acpi/irq.c and some minor style issues.
* Minor bug fixes in the driver.
Changes V9 -> V10:
* Add checks for the producer_consumer field to not use produced IRQ resources as consumed.
* Minor bug fixes in the driver.
Changes V8 -> V9:
* Do not attempt the mapping for non-GSI IRQs during bus scan.
* Make some public APIs private to drivers/acpi/irq.c since they are no longer used on other modules.
Agustin Vega-Frias (3):
ACPI: Generic GSI: Do not attempt to map non-GSI IRQs during bus scan
ACPI: Add support for ResourceSource/IRQ domain mapping
irqchip: qcom: Add IRQ combiner driver
drivers/acpi/Makefile | 2 +-
drivers/acpi/{gsi.c => irq.c} | 221 +++++++++++++++++++++++++
drivers/acpi/resource.c | 18 +-
drivers/base/platform.c | 8 +
drivers/irqchip/Kconfig | 9 +
drivers/irqchip/Makefile | 1 +
drivers/irqchip/qcom-irq-combiner.c | 320 ++++++++++++++++++++++++++++++++++++
include/asm-generic/vmlinux.lds.h | 1 +
include/linux/acpi.h | 15 ++
9 files changed, 593 insertions(+), 2 deletions(-)
rename drivers/acpi/{gsi.c => irq.c} (28%)
create mode 100644 drivers/irqchip/qcom-irq-combiner.c--
Qualcomm Datacenter Technologies, Inc. on behalf of the Qualcomm Technologies, Inc. Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
PATCH v11 1/3 ACPI: Generic GSI: Do not attempt to map non-GSI IRQs during bus scan
ACPI extended IRQ resources may contain a Resource Source field to specify an alternate interrupt controller, attempting to map them as GSIs is incorrect, so just disable the platform resource.
Since this field is currently ignored, we make this change conditional on CONFIG_ACPI_GENERIC_GSI to keep the current behavior on x86 platforms, in case some existing ACPI tables are using this incorrectly.
--- drivers/acpi/resource.c | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)
drivers/acpi/resource.c +17 -1
@@ -43,6 +43,19 @@ static inline bool acpi_iospace_resource_valid(struct resource *res) acpi_iospace_resource_valid(struct resource *res) { return true; }#endif +#ifdef CONFIG_ACPI_GENERIC_GSI +static inline bool is_gsi (struct acpi_resource_extended_irq *ext_irq) +{ +return ext_irq->resource_source.string_length ==0 && + ext_irq->producer_consumer ==ACPI_CONSUMER ; +} +#else +static inline bool is_gsi (struct acpi_resource_extended_irq *ext_irq) +{ +return true; +} +#endif +static bool acpi_dev_resource_len_valid (u64 start,u64 end,u64 len,bool io) {u64 reslen = end - start +1 ;
@@ -470,9 +483,12 @@ bool acpi_dev_resource_interrupt(struct acpi_resource *ares, int index,acpi_dev_irqresource_disabled (res,0 );return false; } -acpi_dev_get_irqresource (res, ext_irq->interrupts[index], +if (is_gsi (ext_irq)) +acpi_dev_get_irqresource (res, ext_irq->interrupts[index], ext_irq->triggering, ext_irq->polarity, ext_irq->sharable, false); +else +acpi_dev_irqresource_disabled (res,0 );break ;default : res->flags =0 ;
Signature · 2 lines
Qualcomm Datacenter Technologies, Inc. on behalf of the Qualcomm Technologies, Inc. Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
Re: [PATCH V11 1/3] ACPI: Generic GSI: Do not attempt to map non-GSI IRQs during bus scan
drivers/acpi/resource.c static inline bool acpi_iospace_resource_valid(struct resource *res) · line 46
Quoted 13 lines · Agustin Vega-Frias
ACPI extended IRQ resources may contain a Resource Source field to specify an alternate interrupt controller, attempting to map them as GSIs is incorrect, so just disable the platform resource.
Since this field is currently ignored, we make this change conditional on
CONFIG_ACPI_GENERIC_GSIto keep the current behavior on x86 platforms, in case some existing ACPI tables are using this incorrectly.drivers/acpi/resource.c +1
-0@@ -43,6 +43,19 @@ static inline bool acpi_iospace_resource_valid(struct resource *res) acpi_iospace_resource_valid(struct resource *res) { return true; }#endif +#ifdef CONFIG_ACPI_GENERIC_GSI
#if IS_ENABLED() ?
Quoted 17 lines
drivers/acpi/resource.c +12
-0+static inline bool is_gsi (struct acpi_resource_extended_irq *ext_irq) +{ +return ext_irq->resource_source.string_length ==0 && + ext_irq->producer_consumer ==ACPI_CONSUMER ; +} +#else +static inline bool is_gsi (struct acpi_resource_extended_irq *ext_irq) +{ +return true; +} +#endif +static bool acpi_dev_resource_len_valid (u64 start,u64 end,u64 len,bool io) {u64 reslen = end - start +1 ;@@ -470,9 +483,12 @@ bool acpi_dev_resource_interrupt(struct acpi_resource *ares, int index,acpi_dev_irqresource_disabled (res,0 );
drivers/acpi/resource.c bool acpi_dev_resource_interrupt(struct acpi_resource *ares, int index, · line 492
Quoted 10 lines
drivers/acpi/resource.c +4
-1return false; } -acpi_dev_get_irqresource (res, ext_irq->interrupts[index], +if (is_gsi (ext_irq)) +acpi_dev_get_irqresource (res, ext_irq->interrupts[index], ext_irq->triggering, ext_irq->polarity, ext_irq->sharable, false); +else +acpi_dev_irqresource_disabled (res,0 );
And why not to create a helper called acpi_dev_get_gsi_irqresource() instead of that one?
Signature · 2 lines
With Best Regards, Andy Shevchenko
Rafael J. Wysocki
maintainerRe: [PATCH V11 1/3] ACPI: Generic GSI: Do not attempt to map non-GSI IRQs during bus scan
In reply to Agustin Vega-FriasQuoted 9 lines · Agustin Vega-Frias
ACPI extended IRQ resources may contain a Resource Source field to specify an alternate interrupt controller, attempting to map them as GSIs is incorrect, so just disable the platform resource.
Since this field is currently ignored, we make this change conditional on
CONFIG_ACPI_GENERIC_GSIto keep the current behavior on x86 platforms, in case some existing ACPI tables are using this incorrectly.Signed-off-by Agustin Vega-Frias <[email protected]>
This one is fine by me, so feel free to add my ACK to it.
Or if you want me to apply it, please let me know.
Quoted 33 lines
--- drivers/acpi/resource.c | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)drivers/acpi/resource.c +13
-1@@ -43,6 +43,19 @@ static inline bool acpi_iospace_resource_valid(struct resource *res) acpi_iospace_resource_valid(struct resource *res) { return true; }#endif +#ifdef CONFIG_ACPI_GENERIC_GSI +static inline bool is_gsi (struct acpi_resource_extended_irq *ext_irq) +{ +return ext_irq->resource_source.string_length ==0 && + ext_irq->producer_consumer ==ACPI_CONSUMER ; +} +#else +static inline bool is_gsi (struct acpi_resource_extended_irq *ext_irq) +{ +return true; +} +#endif +static bool acpi_dev_resource_len_valid (u64 start,u64 end,u64 len,bool io) {u64 reslen = end - start +1 ;@@ -470,9 +483,12 @@ bool acpi_dev_resource_interrupt(struct acpi_resource *ares, int index,acpi_dev_irqresource_disabled (res,0 );return false; } - acpi_dev_get_irqresource(res, ext_irq->interrupts[index],
drivers/acpi/resource.c bool acpi_dev_resource_interrupt(struct acpi_resource *ares, int index,
Quoted 10 lines
drivers/acpi/resource.c +4
-1+if (is_gsi (ext_irq)) +acpi_dev_get_irqresource (res, ext_irq->interrupts[index], ext_irq->triggering, ext_irq->polarity, ext_irq->sharable, false); +else +acpi_dev_irqresource_disabled (res,0 );break ;default : res->flags =0 ; --
Thanks,
Rafael
PATCH v11 2/3 ACPI: Add support for ResourceSource/IRQ domain mapping
In reply to Agustin Vega-FriasACPI extended IRQ resources may contain a ResourceSource to specify an alternate interrupt controller. Introduce acpi_irq_get and use it to implement ResourceSource/IRQ domain mapping.
The new API is similar to of_irq_get and allows re-initialization of a platform resource from the ACPI extended IRQ resource, and provides proper behavior for probe deferral when the domain is not yet present when called.
---
drivers/acpi/Makefile | 2 +-
drivers/acpi/{gsi.c => irq.c} | 221 ++++++++++++++++++++++++++++++++++++++
drivers/base/platform.c | 8 ++
include/asm-generic/vmlinux.lds.h | 1 +
include/linux/acpi.h | 15 +++
5 files changed, 246 insertions(+), 1 deletion(-)
rename drivers/acpi/{gsi.c => irq.c} (28%)drivers/acpi/Makefile +1 -1
@@ -55,7 +55,7 @@ acpi-$(CONFIG_DEBUG_FS) += debugfs.o acpi-$(CONFIG_ACPI_NUMA) += numa.o acpi-$(CONFIG_ACPI_PROCFS_POWER) += cm_sbs.o acpi-y += acpi_lpat.o -acpi-$(CONFIG_ACPI_GENERIC_GSI) += gsi.o +acpi-$(CONFIG_ACPI_GENERIC_GSI) += irq.o acpi-$(CONFIG_ACPI_WATCHDOG) += acpi_watchdog.o # These are (potentially) separate modules
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +221 -0
227 lines not on this page · raw message
drivers/base/platform.c +8 -0
@@ -102,6 +102,14 @@ int platform_get_irq(struct platform_device *dev, unsigned int num) } r =platform_get_resource (dev,IORESOURCE_IRQ , num); +if (r && r->flags &IORESOURCE_DISABLED &&has_acpi_companion (&dev->dev)) { +int ret; + + ret =acpi_irq_get (ACPI_HANDLE (&dev->dev), num, r); +if (ret) +return ret; + } +/* * The resources may pass trigger flags to the irqs that need * to be set up. It so happens that the trigger flags for
include/asm-generic/vmlinux.lds.h +1 -0
@@ -567,6 +567,7 @@ ACPI_PROBE_TABLE(irqchip) \ ACPI_PROBE_TABLE(clksrc) \ ACPI_PROBE_TABLE(iort) \ + ACPI_PROBE_TABLE(dsdt_irqchip) \ EARLYCON_TABLE() #define INIT_TEXT \
include/linux/acpi.h +15 -0
@@ -1056,6 +1056,11 @@ struct acpi_probe_entry { (&ACPI_PROBE_TABLE_END (t) - \ &ACPI_PROBE_TABLE(t))); \ }) + +#define __dsdt_irqchip __section(__dsdt_irqchip_acpi_probe_table) +extern struct acpi_device_id __dsdt_irqchip_acpi_probe_table; +extern struct acpi_device_id __dsdt_irqchip_acpi_probe_table_end; +#else static inline int acpi_dev_get_property(struct acpi_device *adev, const char *name, acpi_object_type type,
@@ -1153,4 +1158,14 @@ static inline void acpi_table_upgrade(void) { }static inline int parse_spcr (bool earlycon) {return 0 ; }#endif +#ifdef CONFIG_ACPI_GENERIC_GSI +int acpi_irq_get (acpi_handle handle,unsigned int index,struct resource *res); +#else +static inline int acpi_irq_get (acpi_handle handle,unsigned int index, +struct resource *res) +{ +return -EINVAL ; +} +#endif +#endif /*_LINUX_ACPI_H*/
Signature · 2 lines
Qualcomm Datacenter Technologies, Inc. on behalf of the Qualcomm Technologies, Inc. Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
Re: [PATCH V11 2/3] ACPI: Add support for ResourceSource/IRQ domain mapping
Quoted 50 lines · Agustin Vega-Frias
ACPI extended IRQ resources may contain a ResourceSource to specify an alternate interrupt controller. Introduce
acpi_irq_getand use it to implement ResourceSource/IRQ domain mapping.The new API is similar to
of_irq_getand allows re-initialization of a platform resource from the ACPI extended IRQ resource, and provides proper behavior for probe deferral when the domain is not yet present when called.Signed-off-by Agustin Vega-Frias <[email protected]>--- drivers/acpi/Makefile | 2 +- drivers/acpi/{gsi.c => irq.c} | 221 ++++++++++++++++++++++++++++++++++++++ drivers/base/platform.c | 8 ++ include/asm-generic/vmlinux.lds.h | 1 + include/linux/acpi.h | 15 +++ 5 files changed, 246 insertions(+), 1 deletion(-) rename drivers/acpi/{gsi.c => irq.c} (28%)drivers/acpi/Makefile +1
-1@@ -55,7 +55,7 @@ acpi-$(CONFIG_DEBUG_FS) += debugfs.o acpi-$(CONFIG_ACPI_NUMA) += numa.o acpi-$(CONFIG_ACPI_PROCFS_POWER) += cm_sbs.o acpi-y += acpi_lpat.o -acpi-$(CONFIG_ACPI_GENERIC_GSI) += gsi.o +acpi-$(CONFIG_ACPI_GENERIC_GSI) += irq.o acpi-$(CONFIG_ACPI_WATCHDOG) += acpi_watchdog.o # These are (potentially) separate modulesdrivers/acpi/irq.c renamed from drivers/acpi/gsi.c +7
-0@@ -85,6 +85,227 @@ void acpi_unregister_gsi(u32 gsi)EXPORT_SYMBOL_GPL (acpi_unregister_gsi);/** +* acpi_get_irq_source_fwhandle() - Retrieve fwhandle from IRQ resource source. +* @source: acpi_resource_source to use for the lookup. +* +* Description: +* Retrieve the fwhandle of the device referenced by the given IRQ resource +* source. In addition to it being a valid ACPI device, its _HID must be +* listed on the probe table of ACPI DSDT irqchips. The check is used to
drivers/acpi/irq.c void acpi_unregister_gsi(u32 gsi) · line 104
Quoted 10 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +10
-0+* determine if a driver for the referenced device is available and decide +* if we should try deferred probing if the device has not been probed yet. +* Drivers must use the __dsdt_irqchip attribute when declaring the table +* of acpi_device_ids for the device, e.g.: +* +* static const struct acpi_device_id my_device_ids[] __dsdt_irqchip = { +* { "ABCD0123", }, +* { } +* }; +*
Ok, thanks for doing that. In my opinion it should be done by reusing the ACPI_DECLARE_PROBE_ENTRY mechanism by simply adding a flag to detect whether the entry refers to a static table or AML and a corresponding acpi_device_id for the matching.
This driver matching mechanism though is just an optimization, the IRQ deferral mechanism you are putting in place is much more important, so for now let's focus on getting code in v10 (plus all cosmetic "fixes" introduced in this patch minus the linker section) agreed upon and upstream, adding this linker section later is not a big deal IMO, it must not slow you down.
So, no need for reposting anything let's focus on the IRQ probe deferral core functionality and get it merged.
Thanks,
Lorenzo
Quoted 273 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +204
-0+* Return: +* The referenced device fwhandle or NULL on failure +*/ +static struct fwnode_handle * +acpi_get_irq_source_fwhandle (const struct acpi_resource_source *source) +{ +struct fwnode_handle *result =NULL ; +struct acpi_device *device; +struct acpi_hardware_id *hwid; +struct acpi_device_id *devid; +acpi_handle handle; +acpi_status status; + +if (!source->string_length) +return acpi_gsi_domain_id; + + status =acpi_get_handle (NULL , source->string_ptr, &handle); +if (WARN_ON (ACPI_FAILURE (status))) +return NULL ; + + device =acpi_bus_get_acpi_device (handle); +if (WARN_ON (!device)) +return NULL ; + +list_for_each_entry (hwid, &device->pnp.ids, list) { +for (devid = &__dsdt_irqchip_acpi_probe_table; + devid < &__dsdt_irqchip_acpi_probe_table_end; devid++) { +if (devid->id && !strcmp (devid->id, hwid->id)) { + result = &device->fwnode; +break ; + } + } + } + +acpi_bus_put_acpi_device (device); + +return result; +} + +/* +* Context for the resource walk used to lookup IRQ resources. +* Contains a return code, the lookup index, and references to the flags +* and fwspec where the result is returned. +*/ +struct acpi_irq_parse_one_ctx { +int rc; +unsigned int index; +unsigned long *res_flags; +struct irq_fwspec *fwspec; +}; + +/** +* acpi_irq_parse_one_match - Handle a matching IRQ resource. +* @fwnode: matching fwnode +* @hwirq: hardware IRQ number +* @triggering: triggering attributes of hwirq +* @polarity: polarity attributes of hwirq +* @polarity: polarity attributes of hwirq +* @shareable: shareable attributes of hwirq +* @ctx: acpi_irq_parse_one_ctx updated by this function +* +* Description: +* Handle a matching IRQ resource by populating the given ctx with +* the information passed. +*/ +static inline void acpi_irq_parse_one_match (struct fwnode_handle *fwnode, +u32 hwirq,u8 triggering, +u8 polarity,u8 shareable, +struct acpi_irq_parse_one_ctx *ctx) +{ +if (!fwnode) +return ; + ctx->rc =0 ; + *ctx->res_flags =acpi_dev_irq_flags (triggering, polarity, shareable); + ctx->fwspec->fwnode = fwnode; + ctx->fwspec->param[0 ] = hwirq; + ctx->fwspec->param[1 ] =acpi_dev_get_irq_type (triggering, polarity); + ctx->fwspec->param_count =2 ; +} + +/** +* acpi_irq_parse_one_cb - Handle the given resource. +* @ares: resource to handle +* @context: context for the walk +* +* Description: +* This is called by acpi_walk_resources passing each resource returned by +* the _CRS method. We only inspect IRQ resources. Since IRQ resources +* might contain multiple interrupts we check if the index is within this +* one's interrupt array, otherwise we subtract the current resource IRQ +* count from the lookup index to prepare for the next resource. +* Once a match is found we call acpi_irq_parse_one_match to populate +* the result and end the walk by returning AE_CTRL_TERMINATE. +* +* Return: +* AE_OK if the walk should continue, AE_CTRL_TERMINATE if a matching +* IRQ resource was found. +*/ +static acpi_status acpi_irq_parse_one_cb (struct acpi_resource *ares, +void *context) +{ +struct acpi_irq_parse_one_ctx *ctx = context; +struct acpi_resource_irq *irq; +struct acpi_resource_extended_irq *eirq; +struct fwnode_handle *fwnode; + +switch (ares->type) { +case ACPI_RESOURCE_TYPE_IRQ : + irq = &ares->data.irq; +if (ctx->index >= irq->interrupt_count) { + ctx->index -= irq->interrupt_count; +return AE_OK ; + } + fwnode = acpi_gsi_domain_id; +acpi_irq_parse_one_match (fwnode, irq->interrupts[ctx->index], + irq->triggering, irq->polarity, + irq->sharable, ctx); +return AE_CTRL_TERMINATE ; +case ACPI_RESOURCE_TYPE_EXTENDED_IRQ : + eirq = &ares->data.extended_irq; +if (eirq->producer_consumer ==ACPI_PRODUCER ) +return AE_OK ; +if (ctx->index >= eirq->interrupt_count) { + ctx->index -= eirq->interrupt_count; +return AE_OK ; + } + fwnode =acpi_get_irq_source_fwhandle (&eirq->resource_source); +acpi_irq_parse_one_match (fwnode, eirq->interrupts[ctx->index], + eirq->triggering, eirq->polarity, + eirq->sharable, ctx); +return AE_CTRL_TERMINATE ; + } + +return AE_OK ; +} + +/** +* acpi_irq_parse_one - Resolve an interrupt for a device +* @handle: the device whose interrupt is to be resolved +* @index: index of the interrupt to resolve +* @fwspec: structure irq_fwspec filled by this function +* @flags: resource flags filled by this function +* +* Description: +* Resolves an interrupt for a device by walking its CRS resources to find +* the appropriate ACPI IRQ resource and populating the given struct irq_fwspec +* and flags. +* +* Return: +* The result stored in ctx.rc by the callback, or the default -EINVAL value +* if an error occurs. +*/ +static int acpi_irq_parse_one (acpi_handle handle,unsigned int index, +struct irq_fwspec *fwspec,unsigned long *flags) +{ +struct acpi_irq_parse_one_ctx ctx = { -EINVAL , index, flags, fwspec }; + +acpi_walk_resources (handle,METHOD_NAME__CRS , acpi_irq_parse_one_cb, &ctx); +return ctx.rc; +} + +/** +* acpi_irq_get - Lookup an ACPI IRQ resource and use it to initialize resource. +* @handle: ACPI device handle +* @index: ACPI IRQ resource index to lookup +* @res: Linux IRQ resource to initialize +* +* Description: +* Look for the ACPI IRQ resource with the given index and use it to initialize +* the given Linux IRQ resource. +* +* Return: +* 0 on success +* -EINVAL if an error occurs +* -EPROBE_DEFER if the IRQ lookup/conversion failed +*/ +int acpi_irq_get (acpi_handle handle,unsigned int index,struct resource *res) +{ +struct irq_fwspec fwspec; +struct irq_domain *domain; +unsigned long flags; +int rc; + + rc =acpi_irq_parse_one (handle, index, &fwspec, &flags); +if (rc) +return rc; + + domain =irq_find_matching_fwnode (fwspec.fwnode,DOMAIN_BUS_ANY ); +if (!domain) +return -EPROBE_DEFER ; + + rc =irq_create_fwspec_mapping (&fwspec); +if (rc <=0 ) +return -EINVAL ; + + res->start = rc; + res->end = rc; + res->flags = flags; + +return 0 ; +} +EXPORT_SYMBOL_GPL (acpi_irq_get); + +/** * acpi_set_irq_model - Setup the GSI irqdomain information * @model: the value assigned to acpi_irq_model * @fwnode: the irq_domain identifier for mapping and looking up drivers/base/platform.c +8
-0@@ -102,6 +102,14 @@ int platform_get_irq(struct platform_device *dev, unsigned int num) } r =platform_get_resource (dev,IORESOURCE_IRQ , num); +if (r && r->flags &IORESOURCE_DISABLED &&has_acpi_companion (&dev->dev)) { +int ret; + + ret =acpi_irq_get (ACPI_HANDLE (&dev->dev), num, r); +if (ret) +return ret; + } +/* * The resources may pass trigger flags to the irqs that need * to be set up. It so happens that the trigger flags for include/asm-generic/vmlinux.lds.h +1
-0@@ -567,6 +567,7 @@ ACPI_PROBE_TABLE(irqchip) \ ACPI_PROBE_TABLE(clksrc) \ ACPI_PROBE_TABLE(iort) \ + ACPI_PROBE_TABLE(dsdt_irqchip) \ EARLYCON_TABLE() #define INIT_TEXT \include/linux/acpi.h +15
-0@@ -1056,6 +1056,11 @@ struct acpi_probe_entry { (&ACPI_PROBE_TABLE_END (t) - \ &ACPI_PROBE_TABLE(t))); \ }) + +#define __dsdt_irqchip __section(__dsdt_irqchip_acpi_probe_table) +extern struct acpi_device_id __dsdt_irqchip_acpi_probe_table; +extern struct acpi_device_id __dsdt_irqchip_acpi_probe_table_end; +#else static inline int acpi_dev_get_property(struct acpi_device *adev, const char *name, acpi_object_type type,@@ -1153,4 +1158,14 @@ static inline void acpi_table_upgrade(void) { }static inline int parse_spcr (bool earlycon) {return 0 ; }#endif +#ifdef CONFIG_ACPI_GENERIC_GSI +int acpi_irq_get (acpi_handle handle,unsigned int index,struct resource *res); +#else +static inline int acpi_irq_get (acpi_handle handle,unsigned int index, +struct resource *res) +{ +return -EINVAL ; +} +#endif +#endif /*_LINUX_ACPI_H*/ Signature · 2 lines
Qualcomm Datacenter Technologies, Inc. on behalf of the Qualcomm Technologies, Inc. Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
Re: [PATCH V11 2/3] ACPI: Add support for ResourceSource/IRQ domain mapping
In reply to Agustin Vega-FriasQuoted 30 lines · Agustin Vega-Frias
ACPI extended IRQ resources may contain a ResourceSource to specify an alternate interrupt controller. Introduce
acpi_irq_getand use it to implement ResourceSource/IRQ domain mapping.The new API is similar to
of_irq_getand allows re-initialization of a platform resource from the ACPI extended IRQ resource, and provides proper behavior for probe deferral when the domain is not yet present when called.drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +21
-0+static struct fwnode_handle * +acpi_get_irq_source_fwhandle (const struct acpi_resource_source *source) +{ +struct fwnode_handle *result =NULL ; +struct acpi_device *device; +struct acpi_hardware_id *hwid; +struct acpi_device_id *devid; +acpi_handle handle; +acpi_status status; + +if (!source->string_length) +return acpi_gsi_domain_id; + + status =acpi_get_handle (NULL , source->string_ptr, &handle); +if (WARN_ON (ACPI_FAILURE (status))) +return NULL ; + + device =acpi_bus_get_acpi_device (handle); +if (WARN_ON (!device)) +return NULL ; +
drivers/acpi/irq.c void acpi_unregister_gsi(u32 gsi) · line 136
Quoted 10 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +8
-0+list_for_each_entry (hwid, &device->pnp.ids, list) { +for (devid = &__dsdt_irqchip_acpi_probe_table; + devid < &__dsdt_irqchip_acpi_probe_table_end; devid++) { +if (devid->id && !strcmp (devid->id, hwid->id)) { + result = &device->fwnode; +break ; + } + }
Looks like a candidate for linker table API. (I recommend to Cc Luis for this part)
Quoted 16 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +15
-0+ } +/** +* acpi_irq_parse_one_match - Handle a matching IRQ resource. +* @fwnode: matching fwnode +* @hwirq: hardware IRQ number +* @triggering: triggering attributes of hwirq +* @polarity: polarity attributes of hwirq +* @polarity: polarity attributes of hwirq +* @shareable: shareable attributes of hwirq +* @ctx: acpi_irq_parse_one_ctx updated by this function +* +* Description: +* Handle a matching IRQ resource by populating the given ctx with +* the information passed. +*/
drivers/acpi/irq.c void acpi_unregister_gsi(u32 gsi) · line 177
Quoted 10 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +8
-0+static inline void acpi_irq_parse_one_match (struct fwnode_handle *fwnode, +u32 hwirq,u8 triggering, +u8 polarity,u8 shareable, +struct acpi_irq_parse_one_ctx *ctx) +{ +if (!fwnode) +return ; + ctx->rc =0 ;
Perhaps ctx->rc = fwnode ? 0 : -EINVAL; ?
Quoted 14 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +13
-0+ *ctx->res_flags =acpi_dev_irq_flags (triggering, polarity, shareable); + ctx->fwspec->fwnode = fwnode; + ctx->fwspec->param[0 ] = hwirq; + ctx->fwspec->param[1 ] =acpi_dev_get_irq_type (triggering, polarity); + ctx->fwspec->param_count =2 ; +} +int acpi_irq_get (acpi_handle handle,unsigned int index,struct resource *res) +{ +struct irq_fwspec fwspec; +struct irq_domain *domain; +unsigned long flags; +int rc; +
drivers/acpi/irq.c void acpi_unregister_gsi(u32 gsi) · line 297
Quoted 10 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +10
-0+ rc =acpi_irq_parse_one (handle, index, &fwspec, &flags); +if (rc) +return rc; + + domain =irq_find_matching_fwnode (fwspec.fwnode,DOMAIN_BUS_ANY ); +if (!domain) +return -EPROBE_DEFER ; + + rc =irq_create_fwspec_mapping (&fwspec); +if (rc <=0 )
Is rc = 0 an error?
Quoted 14 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +9
-0+return -EINVAL ; + + res->start = rc; + res->end = rc; + res->flags = flags; + +return 0 ; +} +EXPORT_SYMBOL_GPL (acpi_irq_get);drivers/base/platform.c +0
-0@@ -102,6 +102,14 @@ int platform_get_irq(struct platform_device *dev, unsigned int num)
drivers/base/platform.c int platform_get_irq(struct platform_device *dev, unsigned int num) · line 112
Quoted 10 lines
drivers/base/platform.c +8
-0r =platform_get_resource (dev,IORESOURCE_IRQ , num); +if (r && r->flags &IORESOURCE_DISABLED &&has_acpi_companion (&dev->dev)) { +int ret; + + ret =acpi_irq_get (ACPI_HANDLE (&dev->dev), num, r); +if (ret) +return ret; + } +#ifdef CONFIG_ACPI_GENERIC_GSI
#if IS_ENABLED()
drivers/base/platform.c int platform_get_irq(struct platform_device *dev, unsigned int num)
Quoted 4 lines
drivers/base/platform.c +4
-0+int acpi_irq_get (acpi_handle handle,unsigned int index,struct resource *res); +#else +static inline int acpi_irq_get (acpi_handle handle,unsigned int index, +struct resource *res)
Perhaps
static inline
int ...
Quoted 4 lines
drivers/base/platform.c +4
-0+{ +return -EINVAL ; +} +#endif
Signature · 2 lines
With Best Regards, Andy Shevchenko
Re: [PATCH V11 2/3] ACPI: Add support for ResourceSource/IRQ domain mapping
Quoted 43 lines · Andy Shevchenko
Quoted 30 lines · Agustin Vega-Frias
ACPI extended IRQ resources may contain a ResourceSource to specify an alternate interrupt controller. Introduce
acpi_irq_getand use it to implement ResourceSource/IRQ domain mapping.The new API is similar to
of_irq_getand allows re-initialization of a platform resource from the ACPI extended IRQ resource, and provides proper behavior for probe deferral when the domain is not yet present when called.drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +21
-0+static struct fwnode_handle * +acpi_get_irq_source_fwhandle (const struct acpi_resource_source *source) +{ +struct fwnode_handle *result =NULL ; +struct acpi_device *device; +struct acpi_hardware_id *hwid; +struct acpi_device_id *devid; +acpi_handle handle; +acpi_status status; + +if (!source->string_length) +return acpi_gsi_domain_id; + + status =acpi_get_handle (NULL , source->string_ptr, &handle); +if (WARN_ON (ACPI_FAILURE (status))) +return NULL ; + + device =acpi_bus_get_acpi_device (handle); +if (WARN_ON (!device)) +return NULL ; +drivers/acpi/irq.c void acpi_unregister_gsi(u32 gsi) · line 136
Quoted 10 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +8
-0+list_for_each_entry (hwid, &device->pnp.ids, list) { +for (devid = &__dsdt_irqchip_acpi_probe_table; + devid < &__dsdt_irqchip_acpi_probe_table_end; devid++) { +if (devid->id && !strcmp (devid->id, hwid->id)) { + result = &device->fwnode; +break ; + } + }
Quoted 2 lines
Looks like a candidate for linker table API. (I recommend to Cc Luis for this part)
This linker table entry scheme is just an optimization and should not gate the series.
Quoted 47 lines
Quoted 16 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +15
-0+ } +/** +* acpi_irq_parse_one_match - Handle a matching IRQ resource. +* @fwnode: matching fwnode +* @hwirq: hardware IRQ number +* @triggering: triggering attributes of hwirq +* @polarity: polarity attributes of hwirq +* @polarity: polarity attributes of hwirq +* @shareable: shareable attributes of hwirq +* @ctx: acpi_irq_parse_one_ctx updated by this function +* +* Description: +* Handle a matching IRQ resource by populating the given ctx with +* the information passed. +*/ drivers/acpi/irq.c void acpi_unregister_gsi(u32 gsi) · line 177
Quoted 10 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +8
-0+static inline void acpi_irq_parse_one_match (struct fwnode_handle *fwnode, +u32 hwirq,u8 triggering, +u8 polarity,u8 shareable, +struct acpi_irq_parse_one_ctx *ctx) +{ +if (!fwnode) +return ; + ctx->rc =0 ;Perhaps
ctx->rc= fwnode ? 0 :-EINVAL; ?Quoted 18 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +17
-0+ *ctx->res_flags =acpi_dev_irq_flags (triggering, polarity, shareable); + ctx->fwspec->fwnode = fwnode; + ctx->fwspec->param[0 ] = hwirq; + ctx->fwspec->param[1 ] =acpi_dev_get_irq_type (triggering, polarity); + ctx->fwspec->param_count =2 ; +} +int acpi_irq_get (acpi_handle handle,unsigned int index,struct resource *res) +{ +struct irq_fwspec fwspec; +struct irq_domain *domain; +unsigned long flags; +int rc; + + rc =acpi_irq_parse_one (handle, index, &fwspec, &flags); +if (rc) +return rc; +
Quoted 8 lines
drivers/acpi/irq.c void acpi_unregister_gsi(u32 gsi) · line 297
Quoted 6 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +6
-0+ domain =irq_find_matching_fwnode (fwspec.fwnode,DOMAIN_BUS_ANY ); +if (!domain) +return -EPROBE_DEFER ; + + rc =irq_create_fwspec_mapping (&fwspec); +if (rc <=0 )Is rc = 0 an error?
Yes.
Quoted 34 lines
Quoted 14 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +9
-0+return -EINVAL ; + + res->start = rc; + res->end = rc; + res->flags = flags; + +return 0 ; +} +EXPORT_SYMBOL_GPL (acpi_irq_get);drivers/base/platform.c +0
-0@@ -102,6 +102,14 @@ int platform_get_irq(struct platform_device *dev, unsigned int num)drivers/base/platform.c int platform_get_irq(struct platform_device *dev, unsigned int num) · line 112
Quoted 10 lines
drivers/base/platform.c +8
-0r =platform_get_resource (dev,IORESOURCE_IRQ , num); +if (r && r->flags &IORESOURCE_DISABLED &&has_acpi_companion (&dev->dev)) { +int ret; + + ret =acpi_irq_get (ACPI_HANDLE (&dev->dev), num, r); +if (ret) +return ret; + } +#ifdef CONFIG_ACPI_GENERIC_GSI #if
IS_ENABLED()drivers/base/platform.c int platform_get_irq(struct platform_device *dev, unsigned int num)
Quoted 4 lines
drivers/base/platform.c +4
-0+int acpi_irq_get (acpi_handle handle,unsigned int index,struct resource *res); +#else +static inline int acpi_irq_get (acpi_handle handle,unsigned int index, +struct resource *res)Perhaps
Quoted 2 lines
static inline
int ...
It is late -rc5 and notwithstanding cosmetics changes, can we make progress with this patch series or not please ?
Thanks,
Lorenzo
Re: [PATCH V11 2/3] ACPI: Add support for ResourceSource/IRQ domain mapping
Quoted 22 lines · Lorenzo Pieralisi
Quoted 21 lines · Andy Shevchenko
Quoted 18 lines · Agustin Vega-Frias
ACPI extended IRQ resources may contain a ResourceSource to specify an alternate interrupt controller. Introduce
acpi_irq_getand use it to implement ResourceSource/IRQ domain mapping.The new API is similar to
of_irq_getand allows re-initialization of a platform resource from the ACPI extended IRQ resource, and provides proper behavior for probe deferral when the domain is not yet present when called.drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +8
-0+list_for_each_entry (hwid, &device->pnp.ids, list) { +for (devid = &__dsdt_irqchip_acpi_probe_table; + devid < &__dsdt_irqchip_acpi_probe_table_end; devid++) { +if (devid->id && !strcmp (devid->id, hwid->id)) { + result = &device->fwnode; +break ; + } + }
Quoted 5 lines
Quoted 2 lines
Looks like a candidate for linker table API. (I recommend to Cc Luis for this part)
This linker table entry scheme is just an optimization and should not gate the series.
That's correct. Though Luis might give some advice regarding to this piece of code.
Quoted 11 lines
Quoted 11 lines
Quoted 1 line
+#ifdef
CONFIG_ACPI_GENERIC_GSI#if
IS_ENABLED()include/linux/acpi.h static inline void acpi_table_upgrade(void) { } · line 1165
Quoted 4 lines
include/linux/acpi.h +4
-0+int acpi_irq_get (acpi_handle handle,unsigned int index,struct resource *res); +#else +static inline int acpi_irq_get (acpi_handle handle,unsigned int index, +struct resource *res)Perhaps
Quoted 5 lines
Quoted 2 lines
static inline
int ...It is late -rc5 and notwithstanding cosmetics changes, can we make progress with this patch series or not please ?
I agree for the second case from what's left above, first one might be useful to amend.
At the end it's a Rafael's word, I'm not insisting on cosmetic changes. So, what about the rest?
Signature · 2 lines
With Best Regards, Andy Shevchenko
Re: [PATCH V11 2/3] ACPI: Add support for ResourceSource/IRQ domain mapping
In reply to Lorenzo PieralisiQuoted 142 lines · Lorenzo Pieralisi
Quoted 43 lines · Andy Shevchenko
Quoted 30 lines · Agustin Vega-Frias
ACPI extended IRQ resources may contain a ResourceSource to specify an alternate interrupt controller. Introduce
acpi_irq_getand use it to implement ResourceSource/IRQ domain mapping.The new API is similar to
of_irq_getand allows re-initialization of a platform resource from the ACPI extended IRQ resource, and provides proper behavior for probe deferral when the domain is not yet present when called.drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +21
-0+static struct fwnode_handle * +acpi_get_irq_source_fwhandle (const struct acpi_resource_source *source) +{ +struct fwnode_handle *result =NULL ; +struct acpi_device *device; +struct acpi_hardware_id *hwid; +struct acpi_device_id *devid; +acpi_handle handle; +acpi_status status; + +if (!source->string_length) +return acpi_gsi_domain_id; + + status =acpi_get_handle (NULL , source->string_ptr, &handle); +if (WARN_ON (ACPI_FAILURE (status))) +return NULL ; + + device =acpi_bus_get_acpi_device (handle); +if (WARN_ON (!device)) +return NULL ; +drivers/acpi/irq.c void acpi_unregister_gsi(u32 gsi) · line 136
Quoted 10 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +8
-0+list_for_each_entry (hwid, &device->pnp.ids, list) { +for (devid = &__dsdt_irqchip_acpi_probe_table; + devid < &__dsdt_irqchip_acpi_probe_table_end; devid++) { +if (devid->id && !strcmp (devid->id, hwid->id)) { + result = &device->fwnode; +break ; + } + }Quoted 2 lines
Looks like a candidate for linker table API. (I recommend to Cc Luis for this part)
This linker table entry scheme is just an optimization and should not gate the series.
Quoted 47 lines
Quoted 16 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +15
-0+ } +/** +* acpi_irq_parse_one_match - Handle a matching IRQ resource. +* @fwnode: matching fwnode +* @hwirq: hardware IRQ number +* @triggering: triggering attributes of hwirq +* @polarity: polarity attributes of hwirq +* @polarity: polarity attributes of hwirq +* @shareable: shareable attributes of hwirq +* @ctx: acpi_irq_parse_one_ctx updated by this function +* +* Description: +* Handle a matching IRQ resource by populating the given ctx with +* the information passed. +*/ drivers/acpi/irq.c void acpi_unregister_gsi(u32 gsi) · line 177
Quoted 10 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +8
-0+static inline void acpi_irq_parse_one_match (struct fwnode_handle *fwnode, +u32 hwirq,u8 triggering, +u8 polarity,u8 shareable, +struct acpi_irq_parse_one_ctx *ctx) +{ +if (!fwnode) +return ; + ctx->rc =0 ;Perhaps
ctx->rc= fwnode ? 0 :-EINVAL; ?Quoted 18 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +17
-0+ *ctx->res_flags =acpi_dev_irq_flags (triggering, polarity, shareable); + ctx->fwspec->fwnode = fwnode; + ctx->fwspec->param[0 ] = hwirq; + ctx->fwspec->param[1 ] =acpi_dev_get_irq_type (triggering, polarity); + ctx->fwspec->param_count =2 ; +} +int acpi_irq_get (acpi_handle handle,unsigned int index,struct resource *res) +{ +struct irq_fwspec fwspec; +struct irq_domain *domain; +unsigned long flags; +int rc; + + rc =acpi_irq_parse_one (handle, index, &fwspec, &flags); +if (rc) +return rc; +Quoted 8 lines
drivers/acpi/irq.c void acpi_unregister_gsi(u32 gsi) · line 297
Quoted 6 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +6
-0+ domain =irq_find_matching_fwnode (fwspec.fwnode,DOMAIN_BUS_ANY ); +if (!domain) +return -EPROBE_DEFER ; + + rc =irq_create_fwspec_mapping (&fwspec); +if (rc <=0 )Is rc = 0 an error?
Yes.
Quoted 34 lines
Quoted 14 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +9
-0+return -EINVAL ; + + res->start = rc; + res->end = rc; + res->flags = flags; + +return 0 ; +} +EXPORT_SYMBOL_GPL (acpi_irq_get);drivers/base/platform.c +0
-0@@ -102,6 +102,14 @@ int platform_get_irq(struct platform_device *dev, unsigned int num)drivers/base/platform.c int platform_get_irq(struct platform_device *dev, unsigned int num) · line 112
Quoted 10 lines
drivers/base/platform.c +8
-0r =platform_get_resource (dev,IORESOURCE_IRQ , num); +if (r && r->flags &IORESOURCE_DISABLED &&has_acpi_companion (&dev->dev)) { +int ret; + + ret =acpi_irq_get (ACPI_HANDLE (&dev->dev), num, r); +if (ret) +return ret; + } +#ifdef CONFIG_ACPI_GENERIC_GSI #if
IS_ENABLED()drivers/base/platform.c int platform_get_irq(struct platform_device *dev, unsigned int num)
Quoted 4 lines
drivers/base/platform.c +4
-0+int acpi_irq_get (acpi_handle handle,unsigned int index,struct resource *res); +#else +static inline int acpi_irq_get (acpi_handle handle,unsigned int index, +struct resource *res)Perhaps
Quoted 5 lines
Quoted 2 lines
static inline
int ...It is late -rc5 and notwithstanding cosmetics changes, can we make progress with this patch series or not please ?
Yes, we can.
I've just returned from travels and have not had the time to look at things in detail yet.
I sent a notice about my travel in advance specifically so people didn't expect me to respond while I was traveling, but obviously everybody simply ignored it and went ahead with their lives. And then I get messages like this which doesn't make me happy at all.
I will start processing things shortly, but there is a backlog I need to work through and this one may not be the first item in it.
Thanks,
Rafael
Re: [PATCH V11 2/3] ACPI: Add support for ResourceSource/IRQ domain mapping
Quoted 151 lines · Rafael J. Wysocki
Quoted 142 lines · Lorenzo Pieralisi
Quoted 43 lines · Andy Shevchenko
Quoted 30 lines · Agustin Vega-Frias
ACPI extended IRQ resources may contain a ResourceSource to specify an alternate interrupt controller. Introduce
acpi_irq_getand use it to implement ResourceSource/IRQ domain mapping.The new API is similar to
of_irq_getand allows re-initialization of a platform resource from the ACPI extended IRQ resource, and provides proper behavior for probe deferral when the domain is not yet present when called.drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +21
-0+static struct fwnode_handle * +acpi_get_irq_source_fwhandle (const struct acpi_resource_source *source) +{ +struct fwnode_handle *result =NULL ; +struct acpi_device *device; +struct acpi_hardware_id *hwid; +struct acpi_device_id *devid; +acpi_handle handle; +acpi_status status; + +if (!source->string_length) +return acpi_gsi_domain_id; + + status =acpi_get_handle (NULL , source->string_ptr, &handle); +if (WARN_ON (ACPI_FAILURE (status))) +return NULL ; + + device =acpi_bus_get_acpi_device (handle); +if (WARN_ON (!device)) +return NULL ; +drivers/acpi/irq.c void acpi_unregister_gsi(u32 gsi) · line 136
Quoted 10 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +8
-0+list_for_each_entry (hwid, &device->pnp.ids, list) { +for (devid = &__dsdt_irqchip_acpi_probe_table; + devid < &__dsdt_irqchip_acpi_probe_table_end; devid++) { +if (devid->id && !strcmp (devid->id, hwid->id)) { + result = &device->fwnode; +break ; + } + }Quoted 2 lines
Looks like a candidate for linker table API. (I recommend to Cc Luis for this part)
This linker table entry scheme is just an optimization and should not gate the series.
Quoted 47 lines
Quoted 16 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +15
-0+ } +/** +* acpi_irq_parse_one_match - Handle a matching IRQ resource. +* @fwnode: matching fwnode +* @hwirq: hardware IRQ number +* @triggering: triggering attributes of hwirq +* @polarity: polarity attributes of hwirq +* @polarity: polarity attributes of hwirq +* @shareable: shareable attributes of hwirq +* @ctx: acpi_irq_parse_one_ctx updated by this function +* +* Description: +* Handle a matching IRQ resource by populating the given ctx with +* the information passed. +*/ drivers/acpi/irq.c void acpi_unregister_gsi(u32 gsi) · line 177
Quoted 10 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +8
-0+static inline void acpi_irq_parse_one_match (struct fwnode_handle *fwnode, +u32 hwirq,u8 triggering, +u8 polarity,u8 shareable, +struct acpi_irq_parse_one_ctx *ctx) +{ +if (!fwnode) +return ; + ctx->rc =0 ;Perhaps
ctx->rc= fwnode ? 0 :-EINVAL; ?Quoted 18 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +17
-0+ *ctx->res_flags =acpi_dev_irq_flags (triggering, polarity, shareable); + ctx->fwspec->fwnode = fwnode; + ctx->fwspec->param[0 ] = hwirq; + ctx->fwspec->param[1 ] =acpi_dev_get_irq_type (triggering, polarity); + ctx->fwspec->param_count =2 ; +} +int acpi_irq_get (acpi_handle handle,unsigned int index,struct resource *res) +{ +struct irq_fwspec fwspec; +struct irq_domain *domain; +unsigned long flags; +int rc; + + rc =acpi_irq_parse_one (handle, index, &fwspec, &flags); +if (rc) +return rc; +Quoted 8 lines
drivers/acpi/irq.c void acpi_unregister_gsi(u32 gsi) · line 297
Quoted 6 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +6
-0+ domain =irq_find_matching_fwnode (fwspec.fwnode,DOMAIN_BUS_ANY ); +if (!domain) +return -EPROBE_DEFER ; + + rc =irq_create_fwspec_mapping (&fwspec); +if (rc <=0 )Is rc = 0 an error?
Yes.
Quoted 34 lines
Quoted 14 lines
drivers/acpi/irq.c renamed from drivers/acpi/gsi.c +9
-0+return -EINVAL ; + + res->start = rc; + res->end = rc; + res->flags = flags; + +return 0 ; +} +EXPORT_SYMBOL_GPL (acpi_irq_get);drivers/base/platform.c +0
-0@@ -102,6 +102,14 @@ int platform_get_irq(struct platform_device *dev, unsigned int num)drivers/base/platform.c int platform_get_irq(struct platform_device *dev, unsigned int num) · line 112
Quoted 10 lines
drivers/base/platform.c +8
-0r =platform_get_resource (dev,IORESOURCE_IRQ , num); +if (r && r->flags &IORESOURCE_DISABLED &&has_acpi_companion (&dev->dev)) { +int ret; + + ret =acpi_irq_get (ACPI_HANDLE (&dev->dev), num, r); +if (ret) +return ret; + } +#ifdef CONFIG_ACPI_GENERIC_GSI #if
IS_ENABLED()drivers/base/platform.c int platform_get_irq(struct platform_device *dev, unsigned int num)
Quoted 4 lines
drivers/base/platform.c +4
-0+int acpi_irq_get (acpi_handle handle,unsigned int index,struct resource *res); +#else +static inline int acpi_irq_get (acpi_handle handle,unsigned int index, +struct resource *res)Perhaps
Quoted 5 lines
Quoted 2 lines
static inline
int ...It is late -rc5 and notwithstanding cosmetics changes, can we make progress with this patch series or not please ?
Yes, we can.
Quoted 7 lines
I've just returned from travels and have not had the time to look at things in detail yet.
I sent a notice about my travel in advance specifically so people didn't expect me to respond while I was traveling, but obviously everybody simply ignored it and went ahead with their lives. And then I get messages like this which doesn't make me happy at all.
I had to ask given that there are other series that depend on it and that this code will eventually have to go via a tree that is not ACPI, so that will require some coordination and it is getting late in the cycle, that's all my message was meant for, apologies.
Quoted 2 lines
I will start processing things shortly, but there is a backlog I need to work through and this one may not be the first item in it.
Ok no problems then, thank you !
Lorenzo
PATCH v11 3/3 irqchip: qcom: Add IRQ combiner driver
In reply to Agustin Vega-FriasDriver for interrupt combiners in the Top-level Control and Status Registers (TCSR) hardware block in Qualcomm Technologies chips.
An interrupt combiner in this block combines a set of interrupts by OR'ing the individual interrupt signals into a summary interrupt signal routed to a parent interrupt controller, and provides read- only, 32-bit registers to query the status of individual interrupts. The status bit for IRQ n is bit (n % 32) within register (n / 32) of the given combiner. Thus, each combiner can be described as a set of register offsets and the number of IRQs managed.
--- drivers/irqchip/Kconfig | 9 + drivers/irqchip/Makefile | 1 + drivers/irqchip/qcom-irq-combiner.c | 320 ++++++++++++++++++++++++++++++++++++ 3 files changed, 330 insertions(+) create mode 100644 drivers/irqchip/qcom-irq-combiner.c
drivers/irqchip/Kconfig +9 -0
@@ -283,3 +283,12 @@ config EZNPS_GIC config STM32_EXTI bool select IRQ_DOMAIN + +config QCOM_IRQ_COMBINER + bool "QCOM IRQ combiner support" + depends on ARCH_QCOM && ACPI + select IRQ_DOMAIN + select IRQ_DOMAIN_HIERARCHY + help + Say yes here to add support for the IRQ combiner devices embedded + in Qualcomm Technologies chips.
drivers/irqchip/Makefile +1 -0
@@ -75,3 +75,4 @@ obj-$(CONFIG_LS_SCFG_MSI) += irq-ls-scfg-msi.o obj-$(CONFIG_EZNPS_GIC) += irq-eznps.o obj-$(CONFIG_ARCH_ASPEED) += irq-aspeed-vic.o obj-$(CONFIG_STM32_EXTI) += irq-stm32-exti.o +obj-$(CONFIG_QCOM_IRQ_COMBINER) += qcom-irq-combiner.o
drivers/irqchip/qcom-irq-combiner.c new file +320 -0
320 lines not on this page · raw message
Signature · 2 lines
Qualcomm Datacenter Technologies, Inc. on behalf of the Qualcomm Technologies, Inc. Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
Quoted 11 lines · Agustin Vega-Frias
Driver for interrupt combiners in the Top-level Control and Status Registers (TCSR) hardware block in Qualcomm Technologies chips.
An interrupt combiner in this block combines a set of interrupts by OR'ing the individual interrupt signals into a summary interrupt signal routed to a parent interrupt controller, and provides read- only, 32-bit registers to query the status of individual interrupts. The status bit for IRQ n is bit (n % 32) within register (n / 32) of the given combiner. Thus, each combiner can be described as a set of register offsets and the number of IRQs managed.
drivers/irqchip/qcom-irq-combiner.c line 56
Quoted 10 lines
drivers/irqchip/qcom-irq-combiner.c new file +10
-0+static inline u32 irq_register (int irq) +{ +return irq /REG_SIZE ; +} + +static inline u32 irq_bit (int irq) +{ +return irq %REG_SIZE ; + +}
Besides extra line I do not see a benefit of those helpers. On first glance they even increase characters to type.
drivers/irqchip/qcom-irq-combiner.c line 61
Quoted 4 lines
drivers/irqchip/qcom-irq-combiner.c new file +4
-0+static inline int irq_nr (u32 reg,u32 bit) +{ +return reg *REG_SIZE + bit; +}
This one might make sense.
Quoted 16 lines
drivers/irqchip/qcom-irq-combiner.c new file +16
-0+static void combiner_handle_irq (struct irq_desc *desc) +{ +struct combiner *combiner =irq_desc_get_handler_data (desc); +struct irq_chip *chip =irq_desc_get_chip (desc); +u32 reg; + +chained_irq_enter (chip, desc); + +for (reg =0 ; reg < combiner->nregs; reg++) { +int virq; +int hwirq; +u32 bit; +u32 status; + + bit =readl_relaxed (combiner->regs[reg].addr); + status = bit & combiner->regs[reg].enabled;
drivers/irqchip/qcom-irq-combiner.c line 90
Quoted 10 lines
drivers/irqchip/qcom-irq-combiner.c new file +9
-0+if (!status) +pr_warn_ratelimited ("Unexpected IRQ on CPU%d: (%08x %08lx %p)\n" , +smp_processor_id (), bit, + combiner->regs[reg].enabled, + combiner->regs[reg].addr); + +while (status) { + bit =__ffs (status); + status &= ~(1 << bit);
Interesting way of for_each_set_bit() ?
Quoted 5 lines
drivers/irqchip/qcom-irq-combiner.c new file +5
-0+ hwirq =irq_nr (reg, bit); + virq =irq_find_mapping (combiner->domain, hwirq); +if (virq >0 ) +generic_handle_irq (virq); +
drivers/irqchip/qcom-irq-combiner.c line 104
Quoted 10 lines
drivers/irqchip/qcom-irq-combiner.c new file +9
-0+ } + } + +chained_irq_exit (chip, desc); +} + +/* +* irqchip callbacks +*/
Useless.
Quoted 3 lines
+/*
+ *irq_domain_opscallbacks
+ */
Ditto.
Quoted 3 lines
+/*
+ * Device probing
+ */
Ditto.
drivers/irqchip/qcom-irq-combiner.c line 178
Quoted 3 lines
drivers/irqchip/qcom-irq-combiner.c new file +3
-0+static acpi_status count_registers_cb (struct acpi_resource *ares,void *context) +{ +int *count = context;
I would consider to define a struct. It would be easy to extend if needed and...
drivers/irqchip/qcom-irq-combiner.c line 181
Quoted 3 lines
drivers/irqchip/qcom-irq-combiner.c new file +3
-0+ +if (ares->type ==ACPI_RESOURCE_TYPE_GENERIC_REGISTER ) + ++(*count);
...allows not to use such of constructions. (I think above is equivalent to ++*count).
drivers/irqchip/qcom-irq-combiner.c line 187
Quoted 7 lines
drivers/irqchip/qcom-irq-combiner.c new file +6
-0+return AE_OK ; +} + +static int count_registers (struct platform_device *pdev) +{ +struct acpi_device *adev =ACPI_COMPANION (&pdev->dev);
You don't use adev, so, ACPI_HANDLE() ?
drivers/irqchip/qcom-irq-combiner.c line 199
Quoted 12 lines
drivers/irqchip/qcom-irq-combiner.c new file +12
-0+acpi_status status; +int count =0 ; + +if (!acpi_has_method (adev->handle,METHOD_NAME__CRS )) +return -EINVAL ; + + status =acpi_walk_resources (adev->handle,METHOD_NAME__CRS , + count_registers_cb, &count); +if (ACPI_FAILURE (status)) +return -EINVAL ; +return count; +}
Oh, since you are using this just as a helper to get count first, why not to combine this in one callback?
What's the benefit of separation?
Quoted 23 lines
drivers/irqchip/qcom-irq-combiner.c new file +23
-0+ +struct get_registers_context { +struct device *dev; +struct combiner *combiner; +int err; +}; + +static acpi_status get_registers_cb (struct acpi_resource *ares,void *context) +{ +struct get_registers_context *ctx = context; +struct acpi_resource_generic_register *reg; +phys_addr_t paddr; +void __iomem *vaddr; + +if (ares->type !=ACPI_RESOURCE_TYPE_GENERIC_REGISTER ) +return AE_OK ; + + reg = &ares->data.generic_reg; + paddr = reg->address; +if ((reg->space_id !=ACPI_SPACE_MEM ) || + (reg->bit_offset !=0 ) || + (reg->bit_width >REG_SIZE )) { +dev_err (ctx->dev,"Bad register resource @%pa\n" , &paddr);
drivers/irqchip/qcom-irq-combiner.c line 232
Quoted 10 lines
drivers/irqchip/qcom-irq-combiner.c new file +10
-0+ ctx->err = -EINVAL ; +return AE_ERROR ; + } + + vaddr =devm_ioremap (ctx->dev, reg->address,REG_SIZE ); +if (IS_ERR (vaddr)) { +dev_err (ctx->dev,"Can't map register @%pa\n" , &paddr); + ctx->err =PTR_ERR (vaddr); +return AE_ERROR ; + }
This all sounds to me like an OperationalRegion. But I'm not sure it's suitable here.
Do you have ACPI table carved in stone?
Quoted 69 lines
drivers/irqchip/qcom-irq-combiner.c new file +69
-0+ + ctx->combiner->regs[ctx->combiner->nregs].addr = vaddr; + ctx->combiner->nirqs += reg->bit_width; + ctx->combiner->nregs++; +return AE_OK ; +} + +static int get_registers (struct platform_device *pdev,struct combiner *comb) +{ +struct acpi_device *adev =ACPI_COMPANION (&pdev->dev); +acpi_status status; +struct get_registers_context ctx; + +if (!acpi_has_method (adev->handle,METHOD_NAME__CRS )) +return -EINVAL ; + + ctx.dev = &pdev->dev; + ctx.combiner = comb; + ctx.err =0 ; + + status =acpi_walk_resources (adev->handle,METHOD_NAME__CRS , + get_registers_cb, &ctx); +if (ACPI_FAILURE (status)) +return ctx.err; +return 0 ; +} + +static int __init combiner_probe (struct platform_device *pdev) +{ +struct combiner *combiner; +size_t alloc_sz; +u32 nregs; +int err; + + nregs =count_registers (pdev); +if (nregs <=0 ) { +dev_err (&pdev->dev,"Error reading register resources\n" ); +return -EINVAL ; + } + + alloc_sz =sizeof (*combiner) +sizeof (struct combiner_reg ) * nregs; + combiner =devm_kzalloc (&pdev->dev, alloc_sz,GFP_KERNEL ); +if (!combiner) +return -ENOMEM ; + + err =get_registers (pdev, combiner); +if (err <0 ) +return err; + + combiner->parent_irq =platform_get_irq (pdev,0 ); +if (combiner->parent_irq <=0 ) { +dev_err (&pdev->dev,"Error getting IRQ resource\n" ); +return -EPROBE_DEFER ; + } + + combiner->domain =irq_domain_create_linear (pdev->dev.fwnode, combiner->nirqs, + &domain_ops, combiner); +if (!combiner->domain) +/* Errors printed by irq_domain_create_linear */ +return -ENODEV ; + +irq_set_chained_handler_and_data (combiner->parent_irq, + combiner_handle_irq, combiner); + +dev_info (&pdev->dev,"Initialized with [p=%d,n=%d,r=%p]\n" , + combiner->parent_irq, combiner->nirqs, combiner->regs[0 ].addr); +return 0 ; +} +
drivers/irqchip/qcom-irq-combiner.c line 310
Quoted 10 lines
drivers/irqchip/qcom-irq-combiner.c new file +9
-0+static const struct acpi_device_id qcom_irq_combiner_ids[] __dsdt_irqchip = { + {"QCOM80B1" , }, + { } +}; + +static struct platform_driver qcom_irq_combiner_probe = { + .driver = { + .name ="qcom-irq-combiner" , + .owner =THIS_MODULE ,
Do you still need this?
Quoted 2 lines
drivers/irqchip/qcom-irq-combiner.c new file +2
-0+ .acpi_match_table = ACPI_PTR(qcom_irq_combiner_ids), + },
Signature · 2 lines
With Best Regards, Andy Shevchenko
Hi Andy,
Quoted 13 lines · Andy Shevchenko
Quoted 10 lines · Agustin Vega-Frias
Driver for interrupt combiners in the Top-level Control and Status Registers (TCSR) hardware block in Qualcomm Technologies chips.
An interrupt combiner in this block combines a set of interrupts by OR'ing the individual interrupt signals into a summary interrupt signal routed to a parent interrupt controller, and provides read- only, 32-bit registers to query the status of individual interrupts. The status bit for IRQ n is bit (n % 32) within register (n / 32) of the given combiner. Thus, each combiner can be described as a set of register offsets and the number of IRQs managed.
Quoted 14 lines
drivers/irqchip/qcom-irq-combiner.c line 56
Quoted 10 lines
drivers/irqchip/qcom-irq-combiner.c new file +10
-0+static inline u32 irq_register (int irq) +{ +return irq /REG_SIZE ; +} + +static inline u32 irq_bit (int irq) +{ +return irq %REG_SIZE ; + +}Besides extra line I do not see a benefit of those helpers. On first glance they even increase characters to type.
Will remove these.
Quoted 32 lines
drivers/irqchip/qcom-irq-combiner.c line 61
Quoted 4 lines
drivers/irqchip/qcom-irq-combiner.c new file +4
-0+static inline int irq_nr (u32 reg,u32 bit) +{ +return reg *REG_SIZE + bit; +}This one might make sense.
Quoted 24 lines
drivers/irqchip/qcom-irq-combiner.c new file +18
-0+static void combiner_handle_irq (struct irq_desc *desc) +{ +struct combiner *combiner =irq_desc_get_handler_data (desc); +struct irq_chip *chip =irq_desc_get_chip (desc); +u32 reg; + +chained_irq_enter (chip, desc); + +for (reg =0 ; reg < combiner->nregs; reg++) { +int virq; +int hwirq; +u32 bit; +u32 status; + + bit =readl_relaxed (combiner->regs[reg].addr); + status = bit & combiner->regs[reg].enabled; +if (!status) + pr_warn_ratelimited("Unexpected IRQ on CPU%d:(%08x %08lx %p)\n",
(quoted diff) +2
-0+ smp_processor_id(), bit, +combiner->regs[reg].enabled,
(quoted diff) +2
-0+ combiner->regs[reg].addr); +
Quoted 6 lines
drivers/irqchip/qcom-irq-combiner.c line 90
Quoted 3 lines
drivers/irqchip/qcom-irq-combiner.c new file +3
-0+while (status) { + bit =__ffs (status); + status &= ~(1 << bit);Interesting way of
for_each_set_bit()?
I'm leaving this as-is since in arm64 using __ffs can be optimized better by using the bic instruction.
Quoted 13 lines
Quoted 12 lines
(quoted diff) +2
-0+ hwirq = irq_nr(reg, bit); + virq = irq_find_mapping(combiner->domain,hwirq);
drivers/irqchip/qcom-irq-combiner.c new file +9
-0+if (virq >0 ) +generic_handle_irq (virq); + + } + } + +chained_irq_exit (chip, desc); +} +
Quoted 6 lines
Quoted 3 lines
+/*
+ * irqchip callbacks
+ */Useless.
Will remove
Quoted 6 lines
Quoted 3 lines
+/*
+ *irq_domain_opscallbacks
+ */Ditto.
Will remove
Quoted 6 lines
Quoted 3 lines
+/*
+ * Device probing
+ */Ditto.
Will remove
Quoted 8 lines
Review
Quoted 4 lines
+static
acpi_statuscount_registers_cb(struct acpi_resource *ares, void *context)(quoted diff) +2
-0+{ + int *count = context;I would consider to define a struct. It would be easy to extend if needed and...
The intent here is always to get the count so I don't see value in adding the struct.
Quoted 7 lines
drivers/irqchip/qcom-irq-combiner.c line 181
Quoted 3 lines
drivers/irqchip/qcom-irq-combiner.c new file +3
-0+ +if (ares->type ==ACPI_RESOURCE_TYPE_GENERIC_REGISTER ) + ++(*count);...allows not to use such of constructions. (I think above is equivalent to ++*count).
IMHO having the parentheses makes the code clearer.
Quoted 10 lines
drivers/irqchip/qcom-irq-combiner.c line 187
Quoted 7 lines
drivers/irqchip/qcom-irq-combiner.c new file +6
-0+return AE_OK ; +} + +static int count_registers (struct platform_device *pdev) +{ +struct acpi_device *adev =ACPI_COMPANION (&pdev->dev);You don't use adev, so,
ACPI_HANDLE()?
Will change
Quoted 8 lines
Quoted 8 lines
drivers/irqchip/qcom-irq-combiner.c new file +8
-0+acpi_status status; +int count =0 ; + +if (!acpi_has_method (adev->handle,METHOD_NAME__CRS )) +return -EINVAL ; + + status =acpi_walk_resources (adev->handle,METHOD_NAME__CRS , + count_registers_cb, &count);
Quoted 9 lines
drivers/irqchip/qcom-irq-combiner.c line 199
Quoted 4 lines
drivers/irqchip/qcom-irq-combiner.c new file +4
-0+if (ACPI_FAILURE (status)) +return -EINVAL ; +return count; +}Oh, since you are using this just as a helper to get count first, why not to combine this in one callback?
What's the benefit of separation?
This is because we do an allocation based on the count first.
Quoted 32 lines
Quoted 32 lines
drivers/irqchip/qcom-irq-combiner.c new file +8
-0+ +struct get_registers_context { +struct device *dev; +struct combiner *combiner; +int err; +}; + +static acpi_status get_registers_cb(struct acpi_resource *ares, void*context)
drivers/irqchip/qcom-irq-combiner.c new file +15
-0+{ +struct get_registers_context *ctx = context; +struct acpi_resource_generic_register *reg; +phys_addr_t paddr; +void __iomem *vaddr; + +if (ares->type !=ACPI_RESOURCE_TYPE_GENERIC_REGISTER ) +return AE_OK ; + + reg = &ares->data.generic_reg; + paddr = reg->address; +if ((reg->space_id !=ACPI_SPACE_MEM ) || + (reg->bit_offset !=0 ) || + (reg->bit_width >REG_SIZE )) { + dev_err(ctx->dev, "Bad register resource @%pa\n",&paddr);
drivers/irqchip/qcom-irq-combiner.c new file +7
-0+ ctx->err = -EINVAL ; +return AE_ERROR ; + } + + vaddr =devm_ioremap (ctx->dev, reg->address,REG_SIZE ); +if (IS_ERR (vaddr)) { + dev_err(ctx->dev, "Can't map register @%pa\n",
Quoted 9 lines
drivers/irqchip/qcom-irq-combiner.c line 232
Quoted 4 lines
&paddr);
drivers/irqchip/qcom-irq-combiner.c new file +3
-0+ ctx->err =PTR_ERR (vaddr); +return AE_ERROR ; + }This all sounds to me like an OperationalRegion. But I'm not sure it's suitable here.
Do you have ACPI table carved in stone?
I decided to go with registers because in some cases these might be non- contiguous.
Quoted 86 lines
Quoted 85 lines
drivers/irqchip/qcom-irq-combiner.c new file +8
-0+ + ctx->combiner->regs[ctx->combiner->nregs].addr = vaddr; + ctx->combiner->nirqs += reg->bit_width; + ctx->combiner->nregs++; +return AE_OK ; +} + +static int get_registers(struct platform_device *pdev, structcombiner *comb)
drivers/irqchip/qcom-irq-combiner.c new file +29
-0+{ +struct acpi_device *adev =ACPI_COMPANION (&pdev->dev); +acpi_status status; +struct get_registers_context ctx; + +if (!acpi_has_method (adev->handle,METHOD_NAME__CRS )) +return -EINVAL ; + + ctx.dev = &pdev->dev; + ctx.combiner = comb; + ctx.err =0 ; + + status =acpi_walk_resources (adev->handle,METHOD_NAME__CRS , + get_registers_cb, &ctx); +if (ACPI_FAILURE (status)) +return ctx.err; +return 0 ; +} + +static int __init combiner_probe (struct platform_device *pdev) +{ +struct combiner *combiner; +size_t alloc_sz; +u32 nregs; +int err; + + nregs =count_registers (pdev); +if (nregs <=0 ) { + dev_err(&pdev->dev, "Error reading registerresources\n");
drivers/irqchip/qcom-irq-combiner.c new file +4
-0+return -EINVAL ; + } + + alloc_sz = sizeof(*combiner) + sizeof(struct combiner_reg) *nregs;
drivers/irqchip/qcom-irq-combiner.c new file +15
-0+ combiner =devm_kzalloc (&pdev->dev, alloc_sz,GFP_KERNEL ); +if (!combiner) +return -ENOMEM ; + + err =get_registers (pdev, combiner); +if (err <0 ) +return err; + + combiner->parent_irq =platform_get_irq (pdev,0 ); +if (combiner->parent_irq <=0 ) { +dev_err (&pdev->dev,"Error getting IRQ resource\n" ); +return -EPROBE_DEFER ; + } + + combiner->domain = irq_domain_create_linear(pdev->dev.fwnode,
combiner->nirqs,
+&domain_ops,
combiner);drivers/irqchip/qcom-irq-combiner.c new file +6
-0+if (!combiner->domain) +/* Errors printed by irq_domain_create_linear */ +return -ENODEV ; + + irq_set_chained_handler_and_data(combiner->parent_irq, + combiner_handle_irq,combiner);
drivers/irqchip/qcom-irq-combiner.c new file +3
-0+ + dev_info(&pdev->dev, "Initialized with [p=%d,n=%d,r=%p]\n", + combiner->parent_irq, combiner->nirqs,combiner->regs[0].addr);
drivers/irqchip/qcom-irq-combiner.c new file +4
-0+return 0 ; +} + +static const struct acpi_device_id qcom_irq_combiner_ids[]
__dsdt_irqchip= {drivers/irqchip/qcom-irq-combiner.c new file +7
-0+ { "QCOM80B1", }, + { } +}; + +static struct platform_driver qcom_irq_combiner_probe = { + .driver = { + .name ="qcom-irq-combiner" ,
Quoted 4 lines
Quoted 1 line
+ .owner =
THIS_MODULE,Do you still need this?
Will remove
Thanks,
Agustin
Quoted 6 lines
drivers/irqchip/qcom-irq-combiner.c line 312
Quoted 2 lines
drivers/irqchip/qcom-irq-combiner.c new file +2
-0+ .acpi_match_table = ACPI_PTR(qcom_irq_combiner_ids), + },--
With Best Regards,
Andy Shevchenko
Signature · 4 lines
Qualcomm Datacenter Technologies, Inc. on behalf of the Qualcomm Technologies, Inc. Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
Rafael J. Wysocki
maintainerQuoted 15 lines · Agustin Vega-Frias
Add support for IRQ combiners in the Top-level Control and Status Registers (TCSR) hardware block in Qualcomm Technologies chips.
The first patch prevents the ACPI core from attempting to map IRQ resources with a valid ResourceSource as GSIs.
The second patch adds support for ResourceSource/IRQ domain mapping and fixes IRQ probe deferral by allowing
platform_deviceIRQ resources to be re-initialized from the corresponding ACPI IRQ resource.Both changes described above are conditional on the
ACPI_GENERIC_GSIconfig.The third patch takes advantage of the new capabilities to implement the driver for the IRQ combiners.
Quoted 6 lines
Tested on top of v4.10-rc4.
Changes V10 -> V11:
* Add probe table and use it to implement driver presence detection.
* Fix kernel doc formatting indrivers/acpi/irq.cand some minor style issues.
* Minor bug fixes in the driver.
I'm travelling now
(http://marc.info/?l=linux-pm&m=148410629024194&w=2), but I'll get to this when I'm back.
Thanks,
Rafael