Skip to contentSkip to conversation

ARM: dts: BCM5301X: QSPI and NAND

PATCH Applied Jon Mason 2 participants 4 messages Feb 8, 2017 – Feb 28, 2017 Device tree bindings

lore
Share & tools
lore

Jon Mason

author
#0 lore raw

cover ARM: dts: BCM5301X: QSPI and NAND

Change the default SPI of the BCM5301X to be the new(-ish) iProc QSPI driver. Testing limited to internal Broadcom systems. So, this might\
need extended testing (though I epxect it to work).

Also, Add NAND to bcm953012k

Jon Mason (2):
ARM: dts: BCM5301X: Add NAND entries to bcm953012k
ARM: dts: BCM5301X: convert to iProc QSPI

 arch/arm/boot/dts/bcm5301x.dtsi  | 50 ++++++++++++++++++++++++----------
 arch/arm/boot/dts/bcm953012k.dts | 58 ++++++++++++++++++++++++++++++++++++++++
 2 files changed, 94 insertions(+), 14 deletions(-)
Signature · 1 line
2.7.4
author
#1 lore raw

PATCH 1/2 ARM: dts: BCM5301X: Add NAND entries to bcm953012k

Add the NAND entry in the DTS

---
 arch/arm/boot/dts/bcm953012k.dts | 32 ++++++++++++++++++++++++++++++++
 1 file changed, 32 insertions(+)
arch/arm/boot/dts/bcm953012k.dts +32 -0
index ae31a58..cb673c7 100644
@@ -52,6 +52,38 @@
 	};
 };
 
+&nand {
+	nandcs at 0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+
+		partition at 0 {
+			label = "nboot";
+			reg = <0x00000000 0x00200000>;
+			read-only;
+		};
+		partition at 200000 {
+			label = "nenv";
+			reg = <0x00200000 0x00400000>;
+		};
+		partition at 600000 {
+			label = "nsystem";
+			reg = <0x00600000 0x00a00000>;
+		};
+		partition at 1000000 {
+			label = "nrootfs";
+			reg = <0x01000000 0x07000000>;
+		};
+	};
+};
+
 &uart0 {
 	status = "okay";
 };
Signature · 1 line
2.7.4
author
#3 lore raw

PATCH 2/2 ARM: dts: BCM5301X: convert to iProc QSPI

In reply to Jon Mason

The iproc-qspi driver is the SPI driver that should be used going forward. Modify the SPI DT entry to use this driver, and add an entry in the bcm953012k DTS file to enable the SPI.

Tested on the bcm953012k board.

---
 arch/arm/boot/dts/bcm5301x.dtsi  | 50 +++++++++++++++++++++++++++++-----------
 arch/arm/boot/dts/bcm953012k.dts | 26 +++++++++++++++++++++
 2 files changed, 62 insertions(+), 14 deletions(-)
arch/arm/boot/dts/bcm5301x.dtsi +36 -14
index a4614c9..0acc02f 100644
@@ -290,20 +290,6 @@
 			};
 		};
 
-		spi at 29000 {
-			reg = <0x00029000 0x1000>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			spi_nor: spi-nor at 0 {
-				compatible = "jedec,spi-nor";
-				reg = <0>;
-				spi-max-frequency = <20000000>;
-				linux,part-probe = "ofpart", "bcm47xxpart";
-				status = "disabled";
-			};
-		};
-
 		gmac0: ethernet at 24000 {
 			reg = <0x24000 0x800>;
 		};
@@ -367,4 +353,40 @@
 
 		brcm,nand-has-wp;
 	};
+
+	spi at 18029200 {
+		compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi";
+		reg = <0x18029200 0x184>,
+		      <0x18029000 0x124>,
+		      <0x1811b408 0x004>,
+		      <0x180293a0 0x01c>;
+		reg-names = "mspi", "bspi", "intr_regs", "intr_status_reg";
+		interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "spi_lr_fullness_reached",
+				  "spi_lr_session_aborted",
+				  "spi_lr_impatient",
+				  "spi_lr_session_done",
+				  "spi_lr_overhead",
+				  "mspi_done",
+				  "mspi_halted";
+		clocks = <&iprocmed>;
+		clock-names = "iprocmed";
+		num-cs = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		spi_nor: spi-nor at 0 {
+			compatible = "jedec,spi-nor";
+			reg = <0>;
+			spi-max-frequency = <20000000>;
+			linux,part-probe = "ofpart", "bcm47xxpart";
+			status = "disabled";
+		};
+	};
 };
arch/arm/boot/dts/bcm953012k.dts +26 -0
index cb673c7..34a7f52 100644
@@ -84,6 +84,32 @@
 	};
 };
 
+&spi_nor {
+	status = "okay";
+	spi-max-frequency = <62500000>;
+	m25p,default-addr-width = <3>;
+
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	partition at 0 {
+		label = "boot";
+		reg = <0x00000000 0x000d0000>;
+	};
+	partition at d000 {
+		label = "env";
+		reg = <0x000d0000 0x00030000>;
+	};
+	partition at 100000 {
+		label = "system";
+		reg = <0x00100000 0x00600000>;
+	};
+	partition at 700000 {
+		label = "rootfs";
+		reg = <0x00700000 0x00900000>;
+	};
+};
+
 &uart0 {
 	status = "okay";
 };
Signature · 1 line
2.7.4