dma: imx-sdma: add 1ms delay to ensure SDMA channel is stopped
Subsystems (2)
PATCH 1/1 dma: imx-sdma: add 1ms delay to ensure SDMA channel is stopped
From: Jiada Wang <[email protected]>
sdma_disable_channel() cannot ensure dma is stopped to access module's FIFOs. Maybe SDMA core is running and accessing BD when disable of corresponding channel, this may cause sometimes even after call of .sdma_disable_channel(), SDMA core still be running and accessing module's FIFOs.
We should add delay of one BD SDMA cost time, the maximum is 1ms. So that SDMA clients by calling .device_terminate_all can ensure SDMA core has really been stopped.
--- drivers/dma/imx-sdma.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-)
drivers/dma/imx-sdma.c +9 -1
@@ -937,6 +937,14 @@ static int sdma_disable_channel(struct dma_chan *chan)return 0 ; } +static int sdma_disable_channel_with_delay (struct dma_chan *chan) +{ +sdma_disable_channel (chan); +mdelay (1 ); + +return 0 ; +} +static void sdma_set_watermarklevel_for_p2p (struct sdma_channel *sdmac) {struct sdma_engine *sdma = sdmac->sdma;
@@ -1828,7 +1836,7 @@ static int sdma_probe(struct platform_device *pdev) sdma->dma_device.device_prep_slave_sg = sdma_prep_slave_sg; sdma->dma_device.device_prep_dma_cyclic = sdma_prep_dma_cyclic; sdma->dma_device.device_config = sdma_config; - sdma->dma_device.device_terminate_all = sdma_disable_channel; + sdma->dma_device.device_terminate_all = sdma_disable_channel_with_delay; sdma->dma_device.src_addr_widths =BIT (DMA_SLAVE_BUSWIDTH_4_BYTES ); sdma->dma_device.dst_addr_widths =BIT (DMA_SLAVE_BUSWIDTH_4_BYTES ); sdma->dma_device.directions =BIT (DMA_DEV_TO_MEM ) |BIT (DMA_MEM_TO_DEV );
Signature · 1 line
2.7.4
Quoted 22 lines · On Fri, Feb 10, 2017 at 06:46:45AM -0800, [email protected] wrote:
From: Jiada Wang <[email protected]>
sdma_disable_channel()cannot ensure dma is stopped to access module's FIFOs. Maybe SDMA core is running and accessing BD when disable of corresponding channel, this may cause sometimes even after call of .sdma_disable_channel(), SDMA core still be running and accessing module's FIFOs.We should add delay of one BD SDMA cost time, the maximum is 1ms. So that SDMA clients by calling .device_terminate_all can ensure SDMA core has really been stopped.
Signed-off-by Jiada Wang <[email protected]>--- drivers/dma/imx-sdma.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-)drivers/dma/imx-sdma.c +0
-0
drivers/dma/imx-sdma.c static int sdma_disable_channel(struct dma_chan *chan) · line 943
Quoted 7 lines
drivers/dma/imx-sdma.c +4
-0@@ -937,6 +937,14 @@ static int sdma_disable_channel(struct dma_chan *chan)return 0 ; } +static int sdma_disable_channel_with_delay (struct dma_chan *chan) +{ +sdma_disable_channel (chan); +mdelay (1 );
what is the gaurantee that 1ms is fine? Shouldn't you poll the bit to see channel is disabled properly..
Quoted 20 lines
drivers/dma/imx-sdma.c +5
-1+ +return 0 ; +} +static void sdma_set_watermarklevel_for_p2p (struct sdma_channel *sdmac) {struct sdma_engine *sdma = sdmac->sdma;@@ -1828,7 +1836,7 @@ static int sdma_probe(struct platform_device *pdev) sdma->dma_device.device_prep_slave_sg = sdma_prep_slave_sg; sdma->dma_device.device_prep_dma_cyclic = sdma_prep_dma_cyclic; sdma->dma_device.device_config = sdma_config; - sdma->dma_device.device_terminate_all = sdma_disable_channel; + sdma->dma_device.device_terminate_all = sdma_disable_channel_with_delay; sdma->dma_device.src_addr_widths =BIT (DMA_SLAVE_BUSWIDTH_4_BYTES ); sdma->dma_device.dst_addr_widths =BIT (DMA_SLAVE_BUSWIDTH_4_BYTES ); sdma->dma_device.directions =BIT (DMA_DEV_TO_MEM ) |BIT (DMA_MEM_TO_DEV );Signature · 1 line
2.7.4
Signature · 1 line
~Vinod
Hello Vinod
Quoted 26 lines · Vinod Koul
Quoted 25 lines · On Fri, Feb 10, 2017 at 06:46:45AM -0800, [email protected] wrote:
From: Jiada Wang <[email protected]>
sdma_disable_channel()cannot ensure dma is stopped to access module's FIFOs. Maybe SDMA core is running and accessing BD when disable of corresponding channel, this may cause sometimes even after call of .sdma_disable_channel(), SDMA core still be running and accessing module's FIFOs.We should add delay of one BD SDMA cost time, the maximum is 1ms. So that SDMA clients by calling .device_terminate_all can ensure SDMA core has really been stopped.
Signed-off-by Jiada Wang <[email protected]>--- drivers/dma/imx-sdma.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-)drivers/dma/imx-sdma.c +0
-0@@ -937,6 +937,14 @@ static int sdma_disable_channel(struct dma_chan *chan)return 0 ; }
Quoted 8 lines
drivers/dma/imx-sdma.c static int sdma_disable_channel(struct dma_chan *chan) · line 943
Quoted 4 lines
drivers/dma/imx-sdma.c +4
-0+static int sdma_disable_channel_with_delay (struct dma_chan *chan) +{ +sdma_disable_channel (chan); +mdelay (1 );what is the gaurantee that 1ms is fine? Shouldn't you poll the bit to see channel is disabled properly..
I got the information from NXP (freescale) R&D team,
according to them, by write '1' to SDMA_H_STATSTOP, only disables
the related sdma channel (so poll HE bit will indicates the channel has been disabled), but it cannot ensure SDMA core stop to access modules' FIFO,
SDMA core may still is running, this is a bug in HW.
regarding if the '1ms' is enough to ensure SDMA core has stopped,
NXP R&D team mentioned:
"we should add some delay of one BD SDMA cost time after disable the channel bit, the maximum is 1ms" so I assume 1ms should work for all cases
Thanks,
Jiada
Quoted 21 lines
Quoted 20 lines
drivers/dma/imx-sdma.c +5
-2+ +return 0 ; +} +static void sdma_set_watermarklevel_for_p2p (struct sdma_channel *sdmac) {struct sdma_engine *sdma = sdmac->sdma;@@ -1828,7 +1836,7 @@ static int sdma_probe(struct platform_device *pdev) sdma->dma_device.device_prep_slave_sg = sdma_prep_slave_sg; sdma->dma_device.device_prep_dma_cyclic = sdma_prep_dma_cyclic; sdma->dma_device.device_config = sdma_config; - sdma->dma_device.device_terminate_all = sdma_disable_channel; + sdma->dma_device.device_terminate_all = sdma_disable_channel_with_delay; sdma->dma_device.src_addr_widths =BIT (DMA_SLAVE_BUSWIDTH_4_BYTES ); sdma->dma_device.dst_addr_widths =BIT (DMA_SLAVE_BUSWIDTH_4_BYTES ); sdma->dma_device.directions =BIT (DMA_DEV_TO_MEM ) |BIT (DMA_MEM_TO_DEV ); --2.7.4
Quoted 8 lines · Jiada Wang
Quoted 8 lines
drivers/dma/imx-sdma.c static int sdma_disable_channel(struct dma_chan *chan) · line 943
Quoted 4 lines
drivers/dma/imx-sdma.c +4
-0+static int sdma_disable_channel_with_delay (struct dma_chan *chan) +{ +sdma_disable_channel (chan); +mdelay (1 );what is the gaurantee that 1ms is fine? Shouldn't you poll the bit to see channel is disabled properly..
Quoted 6 lines
I got the information from NXP (freescale) R&D team, according to them, by write '1' to
SDMA_H_STATSTOP, only disables the related sdma channel (so poll HE bit will indicates the channel has been disabled),
but it cannot ensure SDMA core stop to access modules' FIFO, SDMA core may still is running, this is a bug in HW.
Okay b ut you are not doing the HE bit here..??
Quoted 6 lines
regarding if the '1ms' is enough to ensure SDMA core has stopped, NXP R&D team mentioned:
"we should add some delay of one BD SDMA cost time after disable the channel bit, the maximum is 1ms"
so I assume 1ms should work for all cases
At least please document this in changelog and comments in code.
Signature · 1 line
~Vinod
Hello Vinod
Quoted 9 lines · Vinod Koul
Quoted 8 lines · Jiada Wang
Quoted 8 lines
drivers/dma/imx-sdma.c static int sdma_disable_channel(struct dma_chan *chan) · line 943
Quoted 4 lines
drivers/dma/imx-sdma.c +4
-0+static int sdma_disable_channel_with_delay (struct dma_chan *chan) +{ +sdma_disable_channel (chan); +mdelay (1 );what is the gaurantee that 1ms is fine? Shouldn't you poll the bit to see channel is disabled properly..
Quoted 8 lines
Quoted 6 lines
I got the information from NXP (freescale) R&D team, according to them, by write '1' to
SDMA_H_STATSTOP, only disables the related sdma channel (so poll HE bit will indicates the channel has been disabled),
but it cannot ensure SDMA core stop to access modules' FIFO, SDMA core may still is running, this is a bug in HW.Okay b ut you are not doing the HE bit here..??
by calling sdma_disable_channel(chan) here, sdma driver clears corresponding HE bit, thus disables the channel. But it can't ensure SDMA core is stopped by this operation.
Quoted 9 lines
Quoted 6 lines
regarding if the '1ms' is enough to ensure SDMA core has stopped, NXP R&D team mentioned:
"we should add some delay of one BD SDMA cost time after disable the channel bit, the maximum is 1ms"
so I assume 1ms should work for all casesAt least please document this in changelog and comments in code.
I will update my patch to add comments once all concerns are addressed.
Thanks,
Jiada