usb: dwc3: dual-role support
Subsystems (4)
v2 cover usb: dwc3: dual-role support
Hi,
We rely on the OTG controller block or Extcon to provide us with VBUS and ID line status via an interrupt.
This is then used to switch the controller between host, peripheral and idle roles based on the following table.
ID VBUS dual-role state
-- ---- ---------------
0 x A_HOST - Host controller active
1 0 B_IDLE - Both Host and Gadget controllers inactive
1 1 B_PERIPHERAL - Gadget controller activeSeries depends on
[1] dwc3 trivial fixes - https://lkml.org/lkml/2017/2/15/204
Changelog:
v2:
- Use extcon device for VBUS/ID events if extcon phandle is present.
- Fix bugs during system suspend/resume.
cheers,
-roger
Roger Quadros (4):
usb: dwc3: core.h: add some register definitions
usb: dwc3: omap: don't miss events during suspend/resume
usb: dwc3: add dual-role support
usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Documentation/devicetree/bindings/usb/dwc3.txt | 2 + drivers/usb/dwc3/core.c | 752 ++++++++++++++++++++++++- drivers/usb/dwc3/core.h | 131 ++++- drivers/usb/dwc3/dwc3-omap.c | 16 + drivers/usb/dwc3/gadget.c | 18 +- 5 files changed, 895 insertions(+), 24 deletions(-)
Signature · 1 line
2.7.4
PATCH v2 1/4 usb: dwc3: core.h: add some register definitions
Add OTG and GHWPARAMS6 register definitions
--- drivers/usb/dwc3/core.h | 82 +++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 82 insertions(+)
drivers/usb/dwc3/core.h +82 -0
@@ -204,6 +204,15 @@/* Global User Control 1 Register */ #define DWC3_GUCTL1_DEV_L1_EXIT_BY_HW BIT(24) +/* Global Status Register */ +#define DWC3_GSTS_OTG_IP BIT(10) +#define DWC3_GSTS_BC_IP BIT(9) +#define DWC3_GSTS_ADP_IP BIT(8) +#define DWC3_GSTS_HOST_IP BIT(7) +#define DWC3_GSTS_DEVICE_IP BIT(6) +#define DWC3_GSTS_CSR_TIMEOUT BIT(5) +#define DWC3_GSTS_BUS_ERR_ADDR_VLD BIT(4) +/* Global USB2 PHY Configuration Register */ #define DWC3_GUSB2PHYCFG_PHYSOFTRST BIT(31)#define DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS BIT(30)
@@ -288,6 +297,11 @@#define DWC3_MAX_HIBER_SCRATCHBUFS 15/* Global HWPARAMS6 Register */ +#define DWC3_GHWPARAMS6_BCSUPPORT BIT(14) +#define DWC3_GHWPARAMS6_OTG3SUPPORT BIT(13) +#define DWC3_GHWPARAMS6_ADPSUPPORT BIT(12) +#define DWC3_GHWPARAMS6_HNPSUPPORT BIT(11) +#define DWC3_GHWPARAMS6_SRPSUPPORT BIT(10)#define DWC3_GHWPARAMS6_EN_FPGA BIT(7)/* Global HWPARAMS7 Register */
@@ -469,6 +483,74 @@#define DWC3_DEV_IMOD_INTERVAL_SHIFT 0#define DWC3_DEV_IMOD_INTERVAL_MASK (0xffff << 0) +/* OTG Configuration Register */ +#define DWC3_OCFG_DISPWRCUTTOFF BIT(5) +#define DWC3_OCFG_HIBDISMASK BIT(4) +#define DWC3_OCFG_SFTRSTMASK BIT(3) +#define DWC3_OCFG_OTGVERSION BIT(2) +#define DWC3_OCFG_HNPCAP BIT(1) +#define DWC3_OCFG_SRPCAP BIT(0) + +/* OTG CTL Register */ +#define DWC3_OCTL_OTG3GOERR BIT(7) +#define DWC3_OCTL_PERIMODE BIT(6) +#define DWC3_OCTL_PRTPWRCTL BIT(5) +#define DWC3_OCTL_HNPREQ BIT(4) +#define DWC3_OCTL_SESREQ BIT(3) +#define DWC3_OCTL_TERMSELIDPULSE BIT(2) +#define DWC3_OCTL_DEVSETHNPEN BIT(1) +#define DWC3_OCTL_HSTSETHNPEN BIT(0) + +/* OTG Event Register */ +#define DWC3_OEVT_DEVICEMODE BIT(31) +#define DWC3_OEVT_XHCIRUNSTPSET BIT(27) +#define DWC3_OEVT_DEVRUNSTPSET BIT(26) +#define DWC3_OEVT_HIBENTRY BIT(25) +#define DWC3_OEVT_CONIDSTSCHNG BIT(24) +#define DWC3_OEVT_HRRCONFNOTIF BIT(23) +#define DWC3_OEVT_HRRINITNOTIF BIT(22) +#define DWC3_OEVT_ADEVIDLE BIT(21) +#define DWC3_OEVT_ADEVBHOSTEND BIT(20) +#define DWC3_OEVT_ADEVHOST BIT(19) +#define DWC3_OEVT_ADEVHNPCHNG BIT(18) +#define DWC3_OEVT_ADEVSRPDET BIT(17) +#define DWC3_OEVT_ADEVSESSENDDET BIT(16) +#define DWC3_OEVT_BDEVBHOSTEND BIT(11) +#define DWC3_OEVT_BDEVHNPCHNG BIT(10) +#define DWC3_OEVT_BDEVSESSVLDDET BIT(9) +#define DWC3_OEVT_BDEVVBUSCHNG BIT(8) +#define DWC3_OEVT_BSESSVLD BIT(3) +#define DWC3_OEVT_HSTNEGSTS BIT(2) +#define DWC3_OEVT_SESREQSTS BIT(1) +#define DWC3_OEVT_ERROR BIT(0) + +/* OTG Event Enable Register */ +#define DWC3_OEVTEN_XHCIRUNSTPSETEN BIT(27) +#define DWC3_OEVTEN_DEVRUNSTPSETEN BIT(26) +#define DWC3_OEVTEN_HIBENTRYEN BIT(25) +#define DWC3_OEVTEN_CONIDSTSCHNGEN BIT(24) +#define DWC3_OEVTEN_HRRCONFNOTIFEN BIT(23) +#define DWC3_OEVTEN_HRRINITNOTIFEN BIT(22) +#define DWC3_OEVTEN_ADEVIDLEEN BIT(21) +#define DWC3_OEVTEN_ADEVBHOSTENDEN BIT(20) +#define DWC3_OEVTEN_ADEVHOSTEN BIT(19) +#define DWC3_OEVTEN_ADEVHNPCHNGEN BIT(18) +#define DWC3_OEVTEN_ADEVSRPDETEN BIT(17) +#define DWC3_OEVTEN_ADEVSESSENDDETEN BIT(16) +#define DWC3_OEVTEN_BDEVHOSTENDEN BIT(11) +#define DWC3_OEVTEN_BDEVHNPCHNGEN BIT(10) +#define DWC3_OEVTEN_BDEVSESSVLDDETEN BIT(9) +#define DWC3_OEVTEN_BDEVVBUSCHNGE BIT(8) + +/* OTG Status Register */ +#define DWC3_OSTS_DEVRUNSTP BIT(13) +#define DWC3_OSTS_XHCIRUNSTP BIT(12) +#define DWC3_OSTS_PERIPHERALSTATE BIT(4) +#define DWC3_OSTS_XHCIPRTPOWER BIT(3) +#define DWC3_OSTS_BSESVLD BIT(2) +#define DWC3_OSTS_VBUSVLD BIT(1) +#define DWC3_OSTS_CONIDSTS BIT(0) +/* Structures */ struct dwc3_trb ;
Signature · 1 line
2.7.4
PATCH v2 2/4 usb: dwc3: omap: don't miss events during suspend/resume
In reply to Roger QuadrosThe USB cable state can change during suspend/resume so be sure to check and update the extcon state.
--- drivers/usb/dwc3/dwc3-omap.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)
drivers/usb/dwc3/dwc3-omap.c +16 -0
@@ -598,9 +598,25 @@ static int dwc3_omap_resume(struct device *dev)return 0 ; } +static void dwc3_omap_complete (struct device *dev) +{ +struct dwc3_omap *omap =dev_get_drvdata (dev); + +if (extcon_get_state (omap->edev,EXTCON_USB )) +dwc3_omap_set_mailbox (omap,OMAP_DWC3_VBUS_VALID ); +else +dwc3_omap_set_mailbox (omap,OMAP_DWC3_VBUS_OFF ); + +if (extcon_get_state (omap->edev,EXTCON_USB_HOST )) +dwc3_omap_set_mailbox (omap,OMAP_DWC3_ID_GROUND ); +else +dwc3_omap_set_mailbox (omap,OMAP_DWC3_ID_FLOAT ); +} +static const struct dev_pm_ops dwc3_omap_dev_pm_ops = {SET_SYSTEM_SLEEP_PM_OPS (dwc3_omap_suspend, dwc3_omap_resume) + .complete = dwc3_omap_complete, };#define DEV_PM_OPS (&dwc3_omap_dev_pm_ops)
Signature · 1 line
2.7.4
PATCH v2 3/4 usb: dwc3: add dual-role support
In reply to Roger QuadrosIf dr_mode is "otg" then support dual role mode of operation.
Get ID and VBUS information from the OTG controller and put the controller in the appropriate state.
This is our dual-role state table.
ID VBUS dual-role state
-- ---- ---------------
0 x A_HOST - Host controller active
1 0 B_IDLE - Both Host and Gadget controllers inactive
1 1 B_PERIPHERAL - Gadget controller active
Calling dwc3_otg_fsm_sync() directly from dwc3_complete() can lock up the system at xHCI add/remove so we use a work queue for it.
--- drivers/usb/dwc3/core.c | 595 ++++++++++++++++++++++++++++++++++++++++++++-- drivers/usb/dwc3/core.h | 44 +++- drivers/usb/dwc3/gadget.c | 18 +- 3 files changed, 633 insertions(+), 24 deletions(-)
drivers/usb/dwc3/core.c +577 -18
@@ -27,6 +27,7 @@#include <linux/platform_device.h> #include <linux/pm_runtime.h> #include <linux/interrupt.h> +#include <linux/irq.h> #include <linux/ioport.h> #include <linux/io.h> #include <linux/list.h>
@@ -107,6 +108,7 @@ void dwc3_set_mode(struct dwc3 *dwc, u32 mode) reg =dwc3_readl (dwc->regs,DWC3_GCTL ); reg &= ~(DWC3_GCTL_PRTCAPDIR (DWC3_GCTL_PRTCAP_OTG )); reg |=DWC3_GCTL_PRTCAPDIR (mode); + dwc->current_mode = mode;dwc3_writel (dwc->regs,DWC3_GCTL , reg); }
@@ -839,6 +841,505 @@ static int dwc3_core_get_phy(struct dwc3 *dwc)return 0 ; } +static int dwc3_drd_start_host (struct dwc3 *dwc,int on,bool skip); +static int dwc3_drd_start_gadget (struct dwc3 *dwc,int on); + +/* dwc->lock must be held */ +static void dwc3_drd_statemachine (struct dwc3 *dwc,int id,int vbus) +{ +enum usb_otg_state new_state; +int protocol; + +if (id == dwc->otg_fsm.id && vbus == dwc->otg_fsm.b_sess_vld) +return ; + + dwc->otg_fsm.id = id; + dwc->otg_fsm.b_sess_vld = vbus; + +if (!id) { + new_state =OTG_STATE_A_HOST ; + }else { +if (vbus) + new_state =OTG_STATE_B_PERIPHERAL ; +else + new_state =OTG_STATE_B_IDLE ; + } + +if (dwc->otg.state == new_state) +return ; + + protocol = dwc->otg_fsm.protocol; +switch (new_state) { +case OTG_STATE_B_IDLE : +if (protocol ==PROTO_GADGET ) +dwc3_drd_start_gadget (dwc,0 ); +else if (protocol ==PROTO_HOST ) +dwc3_drd_start_host (dwc,0 ,0 ); + dwc->otg_fsm.protocol =PROTO_UNDEF ; +break ; +case OTG_STATE_B_PERIPHERAL : +if (protocol ==PROTO_HOST ) +dwc3_drd_start_host (dwc,0 ,0 ); + +if (protocol !=PROTO_GADGET ) { + dwc->otg_fsm.protocol =PROTO_GADGET ; +dwc3_drd_start_gadget (dwc,1 ); + } +break ; +case OTG_STATE_A_HOST : +if (protocol ==PROTO_GADGET ) +dwc3_drd_start_gadget (dwc,0 ); + +if (protocol !=PROTO_HOST ) { + dwc->otg_fsm.protocol =PROTO_HOST ; +dwc3_drd_start_host (dwc,1 ,0 ); + } +break ; +default : +dev_err (dwc->dev,"drd: invalid usb-drd state: %s\n" , +usb_otg_state_string (new_state)); +return ; + } + + dwc->otg.state = new_state; +} + +/* dwc->lock must be held */ +static void dwc3_otg_fsm_sync (struct dwc3 *dwc) +{ +u32 reg; +int id, vbus; + +/* +* calling dwc3_otg_fsm_sync() during resume breaks host +* if adapter was removed during suspend as xhci driver +* is not prepared to see hcd removal before xhci_resume. +*/ +if (dwc->otg_prevent_sync) +return ; + + reg =dwc3_readl (dwc->regs,DWC3_OSTS ); + id = !!(reg &DWC3_OSTS_CONIDSTS ); + vbus = !!(reg &DWC3_OSTS_BSESVLD ); +dwc3_drd_statemachine (dwc, id, vbus); +} + +static void dwc3_drd_work (struct work_struct *work) +{ + struct dwc3 *dwc = container_of(work, struct dwc3, + otg_work); + +spin_lock (&dwc->lock); +dwc3_otg_fsm_sync (dwc); +spin_unlock (&dwc->lock); +} + +static void dwc3_otg_disable_events (struct dwc3 *dwc,u32 disable_mask) +{ + dwc->oevten &= ~(disable_mask); +dwc3_writel (dwc->regs,DWC3_OEVTEN , dwc->oevten); +} + +static void dwc3_otg_enable_events (struct dwc3 *dwc,u32 enable_mask) +{ + dwc->oevten |= (enable_mask); +dwc3_writel (dwc->regs,DWC3_OEVTEN , dwc->oevten); +} + +#define DWC3_OTG_ALL_EVENTS (DWC3_OEVTEN_XHCIRUNSTPSETEN | \ + DWC3_OEVTEN_DEVRUNSTPSETEN | DWC3_OEVTEN_HIBENTRYEN | \ + DWC3_OEVTEN_CONIDSTSCHNGEN | DWC3_OEVTEN_HRRCONFNOTIFEN | \ + DWC3_OEVTEN_HRRINITNOTIFEN | DWC3_OEVTEN_ADEVIDLEEN | \ + DWC3_OEVTEN_ADEVBHOSTENDEN | DWC3_OEVTEN_ADEVHOSTEN | \ + DWC3_OEVTEN_ADEVHNPCHNGEN | DWC3_OEVTEN_ADEVSRPDETEN | \ + DWC3_OEVTEN_ADEVSESSENDDETEN | DWC3_OEVTEN_BDEVHOSTENDEN | \ + DWC3_OEVTEN_BDEVHNPCHNGEN | DWC3_OEVTEN_BDEVSESSVLDDETEN | \ + DWC3_OEVTEN_BDEVVBUSCHNGE) + +static irqreturn_t dwc3_otg_thread_irq (int irq,void *_dwc) +{ +struct dwc3 *dwc = _dwc; + +spin_lock (&dwc->lock); +if (dwc->otg_needs_host_start) { +dwc3_drd_start_host (dwc, true,1 ); + dwc->otg_needs_host_start =0 ; + } + +dwc3_otg_fsm_sync (dwc); +spin_unlock (&dwc->lock); + +return IRQ_HANDLED ; +} + +static irqreturn_t dwc3_otg_irq (int irq,void *_dwc) +{ +u32 reg; +struct dwc3 *dwc = _dwc; +irqreturn_t ret =IRQ_NONE ; + + reg =dwc3_readl (dwc->regs,DWC3_OEVT ); +if (reg) { +if ((dwc->otg_fsm.protocol ==PROTO_HOST ) && + !(reg &DWC3_OEVT_DEVICEMODE )) + dwc->otg_needs_host_start =1 ; +dwc3_writel (dwc->regs,DWC3_OEVT , reg); + ret =IRQ_WAKE_THREAD ; + } + +return ret; +} + +/* --------------------- Dual-Role management ------------------------------- */ +static void dwc3_otgregs_init (struct dwc3 *dwc) +{ +u32 reg; + +/* +* Prevent host/device reset from resetting OTG core. +* If we don't do this then xhci_reset (USBCMD.HCRST) will reset +* the signal outputs sent to the PHY, the OTG FSM logic of the +* core and also the resets to the VBUS filters inside the core. +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg |=DWC3_OCFG_SFTRSTMASK ; +dwc3_writel (dwc->regs,DWC3_OCFG , reg); + +/* Disable hibernation for simplicity */ + reg =dwc3_readl (dwc->regs,DWC3_GCTL ); + reg &= ~DWC3_GCTL_GBLHIBERNATIONEN ; +dwc3_writel (dwc->regs,DWC3_GCTL , reg); + +/* +* Initialize OTG registers as per +* Figure 11-4 OTG Driver Overall Programming Flow +*/ +/* OCFG.SRPCap = 0, OCFG.HNPCap = 0 */ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~(DWC3_OCFG_SRPCAP |DWC3_OCFG_HNPCAP ); +dwc3_writel (dwc->regs,DWC3_OCFG , reg); +/* OEVT = FFFF */ +dwc3_writel (dwc->regs,DWC3_OEVT , ~0 ); +/* OEVTEN = 0 */ +dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS ); +/* OEVTEN.ConIDStsChngEn = 1. Instead we enable all events */ +dwc3_otg_enable_events (dwc,DWC3_OTG_ALL_EVENTS ); +/* +* OCTL.PeriMode = 1, OCTL.DevSetHNPEn = 0, OCTL.HstSetHNPEn = 0, +* OCTL.HNPReq = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg |=DWC3_OCTL_PERIMODE ; + reg &= ~(DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HSTSETHNPEN | +DWC3_OCTL_HNPREQ ); +dwc3_writel (dwc->regs,DWC3_OCTL , reg); +} + +/* dwc->lock must be held */ +static int dwc3_drd_start_host (struct dwc3 *dwc,int on,bool skip) +{ +u32 reg; + +/* switch OTG core */ +if (on) { +/* As per Figure 11-10 A-Device Flow Diagram */ +/* OCFG.HNPCap = 0, OCFG.SRPCap = 0 */ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~(DWC3_OCFG_SRPCAP |DWC3_OCFG_HNPCAP ); +dwc3_writel (dwc->regs,DWC3_OCFG , reg); + +/* +* OCTL.PeriMode=0, OCTL.TermSelDLPulse = 0, +* OCTL.DevSetHNPEn = 0, OCTL.HstSetHNPEn = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg &= ~(DWC3_OCTL_PERIMODE |DWC3_OCTL_TERMSELIDPULSE | +DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HSTSETHNPEN ); +dwc3_writel (dwc->regs,DWC3_OCTL , reg); + +/* +* OCFG.DisPrtPwrCutoff = 0/1 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~DWC3_OCFG_DISPWRCUTTOFF ; +dwc3_writel (dwc->regs,DWC3_OCFG , reg); + +/* start the xHCI host driver */ +if (!skip) { +spin_unlock (&dwc->lock); +dwc3_host_init (dwc); +spin_lock (&dwc->lock); + } + +/* +* OCFG.SRPCap = 1, OCFG.HNPCap = GHWPARAMS6.HNP_CAP +* We don't want SRP/HNP for simple dual-role so leave +* these disabled. +*/ + +/* +* OEVTEN.OTGADevHostEvntEn = 1 +* OEVTEN.OTGADevSessEndDetEvntEn = 1 +* We don't want HNP/role-swap so leave these disabled. +*/ + +/* GUSB2PHYCFG.ULPIAutoRes = 1/0, GUSB2PHYCFG.SusPHY = 1 */ +if (!dwc->dis_u2_susphy_quirk) { + reg =dwc3_readl (dwc->regs,DWC3_GUSB2PHYCFG (0 )); + reg |=DWC3_GUSB2PHYCFG_SUSPHY ; +dwc3_writel (dwc->regs,DWC3_GUSB2PHYCFG (0 ), reg); + } + +/* Set Port Power to enable VBUS: OCTL.PrtPwrCtl = 1 */ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg |=DWC3_OCTL_PRTPWRCTL ; +dwc3_writel (dwc->regs,DWC3_OCTL , reg); + }else { +/* +* Exit from A-device flow as per +* Figure 11-4 OTG Driver Overall Programming Flow +*/ +/* stop the HCD */ +if (!skip) { +spin_unlock (&dwc->lock); +dwc3_host_exit (dwc); +spin_lock (&dwc->lock); + } + +/* +* OEVTEN.OTGADevBHostEndEvntEn=0, OEVTEN.OTGADevHNPChngEvntEn=0 +* OEVTEN.OTGADevSessEndDetEvntEn=0, +* OEVTEN.OTGADevHostEvntEn = 0 +* But we don't disable any OTG events +*/ + +/* OCTL.HstSetHNPEn = 0, OCTL.PrtPwrCtl=0 */ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg &= ~(DWC3_OCTL_HSTSETHNPEN |DWC3_OCTL_PRTPWRCTL ); +dwc3_writel (dwc->regs,DWC3_OCTL , reg); + +/* Initialize OTG registers */ +dwc3_otgregs_init (dwc); + } + +return 0 ; +} + +/* dwc->lock must be held */ +static int dwc3_drd_start_gadget (struct dwc3 *dwc,int on) +{ +u32 reg; + +if (on) +dwc3_event_buffers_setup (dwc); + +if (on) { +/* As per Figure 11-20 B-Device Flow Diagram */ + +/* +* OCFG.HNPCap = GHWPARAMS6.HNP_CAP, OCFG.SRPCap = 1 +* but we set them to 0 for simple dual-role operation. +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~(DWC3_OCFG_SRPCAP |DWC3_OCFG_HNPCAP ); +/* OCFG.OTGSftRstMsk = 0/1 */ + reg |=DWC3_OCFG_SFTRSTMASK ; +dwc3_writel (dwc->regs,DWC3_OCFG , reg); +/* +* OCTL.PeriMode = 1 +* OCTL.TermSelDLPulse = 0/1, OCTL.HNPReq = 0 +* OCTL.DevSetHNPEn = 0, OCTL.HstSetHNPEn = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg |=DWC3_OCTL_PERIMODE ; + reg &= ~(DWC3_OCTL_TERMSELIDPULSE |DWC3_OCTL_HNPREQ | +DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HSTSETHNPEN ); +dwc3_writel (dwc->regs,DWC3_OCTL , reg); +/* OEVTEN.OTGBDevSesVldDetEvntEn = 1 */ +dwc3_otg_enable_events (dwc,DWC3_OEVT_BDEVSESSVLDDET ); +/* GUSB2PHYCFG.ULPIAutoRes = 0, GUSB2PHYCFG0.SusPHY = 1 */ +if (!dwc->dis_u2_susphy_quirk) { + reg =dwc3_readl (dwc->regs,DWC3_GUSB2PHYCFG (0 )); + reg |=DWC3_GUSB2PHYCFG_SUSPHY ; +dwc3_writel (dwc->regs,DWC3_GUSB2PHYCFG (0 ), reg); + } +/* GCTL.GblHibernationEn = 0 */ + reg =dwc3_readl (dwc->regs,DWC3_GCTL ); + reg &= ~DWC3_GCTL_GBLHIBERNATIONEN ; +dwc3_writel (dwc->regs,DWC3_GCTL , reg); + +/* start the Peripheral driver */ +if (dwc->gadget_driver) { +__dwc3_gadget_start (dwc); +if (dwc->gadget_pullup) +dwc3_gadget_run_stop (dwc, true, false); + } + }else { +/* +* Exit from B-device flow as per +* Figure 11-4 OTG Driver Overall Programming Flow +*/ +/* stop the Peripheral driver */ +if (dwc->gadget_driver) { +if (dwc->gadget_pullup) +dwc3_gadget_run_stop (dwc, false, false); +spin_unlock (&dwc->lock); +if (dwc->gadget_driver->disconnect) + dwc->gadget_driver->disconnect (&dwc->gadget); +spin_lock (&dwc->lock); +__dwc3_gadget_stop (dwc); + } + +/* +* OEVTEN.OTGBDevHNPChngEvntEn = 0 +* OEVTEN.OTGBDevVBusChngEvntEn = 0 +* OEVTEN.OTGBDevBHostEndEvntEn = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OEVTEN ); + reg &= ~(DWC3_OEVT_BDEVHNPCHNG |DWC3_OEVT_BDEVVBUSCHNG | +DWC3_OEVT_BDEVBHOSTEND ); +dwc3_writel (dwc->regs,DWC3_OEVTEN , reg); + +/* OCTL.DevSetHNPEn = 0, OCTL.HNPReq = 0, OCTL.PeriMode=1 */ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg &= ~(DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HNPREQ ); + reg |=DWC3_OCTL_PERIMODE ; +dwc3_writel (dwc->regs,DWC3_OCTL , reg); + +/* Initialize OTG registers */ +dwc3_otgregs_init (dwc); + } + +return 0 ; +} + +static int dwc3_otg_get_irq (struct dwc3 *dwc) +{ +struct platform_device *dwc3_pdev =to_platform_device (dwc->dev); +int irq; + + irq =platform_get_irq_byname (dwc3_pdev,"otg" ); +if (irq >0 ) + goto out; + +if (irq == -EPROBE_DEFER ) + goto out; + + irq =platform_get_irq_byname (dwc3_pdev,"dwc_usb3" ); +if (irq >0 ) + goto out; + +if (irq == -EPROBE_DEFER ) + goto out; + + irq =platform_get_irq (dwc3_pdev,0 ); +if (irq >0 ) + goto out; + +if (irq != -EPROBE_DEFER ) +dev_err (dwc->dev,"missing otg IRQ\n" ); + +if (!irq) + irq = -EINVAL ; + +out: +return irq; +} + +/* dwc->lock must be held */ +static void dwc3_otg_core_init (struct dwc3 *dwc) +{ +u32 reg; + +/* +* As per Figure 11-4 OTG Driver Overall Programming Flow, +* block "Initialize GCTL for OTG operation". +*/ +/* GCTL.PrtCapDir=2'b11 */ +dwc3_set_mode (dwc,DWC3_GCTL_PRTCAP_OTG ); +/* GUSB2PHYCFG0.SusPHY=0 */ + reg =dwc3_readl (dwc->regs,DWC3_GUSB2PHYCFG (0 )); + reg &= ~DWC3_GUSB2PHYCFG_SUSPHY ; +dwc3_writel (dwc->regs,DWC3_GUSB2PHYCFG (0 ), reg); + +/* Initialize OTG registers */ +dwc3_otgregs_init (dwc); + +/* force drd state machine update the first time */ + dwc->otg_fsm.b_sess_vld =-1 ; + dwc->otg_fsm.id =-1 ; +} + +/* dwc->lock must be held */ +static void dwc3_otg_core_exit (struct dwc3 *dwc) +{ +/* disable all otg irqs */ +dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS ); +/* clear all events */ +dwc3_writel (dwc->regs,DWC3_OEVT , ~0 ); +} + +static int dwc3_drd_init (struct dwc3 *dwc) +{ +int ret, irq; +unsigned long flags; + +INIT_WORK (&dwc->otg_work, dwc3_drd_work); + + irq =dwc3_otg_get_irq (dwc); +if (irq <0 ) +return irq; + + dwc->otg_irq = irq; + +/* disable all otg irqs */ +dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS ); +/* clear all events */ +dwc3_writel (dwc->regs,DWC3_OEVT , ~0 ); + +irq_set_status_flags (dwc->otg_irq,IRQ_NOAUTOEN ); + ret =request_threaded_irq (dwc->otg_irq, dwc3_otg_irq, + dwc3_otg_thread_irq, +IRQF_SHARED ,"dwc3-otg" , dwc); +if (ret) { +dev_err (dwc->dev,"failed to request irq #%d --> %d\n" , + dwc->otg_irq, ret); + ret = -ENODEV ; +return ret; + } + + ret =dwc3_gadget_init (dwc); +if (ret) { +free_irq (dwc->otg_irq, dwc); +return ret; + } + +spin_lock_irqsave (&dwc->lock, flags); +dwc3_otg_core_init (dwc); +spin_unlock_irqrestore (&dwc->lock, flags); +queue_work (system_power_efficient_wq, &dwc->otg_work); + +return 0 ; +} + +static void dwc3_drd_exit (struct dwc3 *dwc) +{ +unsigned long flags; + +cancel_work_sync (&dwc->otg_work); +spin_lock_irqsave (&dwc->lock, flags); +dwc3_otg_core_exit (dwc); +if (dwc->otg_fsm.protocol ==PROTO_HOST ) +dwc3_drd_start_host (dwc,0 ,0 ); + dwc->otg_fsm.protocol =PROTO_UNDEF ; +free_irq (dwc->otg_irq, dwc); +spin_unlock_irqrestore (&dwc->lock, flags); + +dwc3_gadget_exit (dwc); +} + +/* -------------------------------------------------------------------------- */ +static int dwc3_core_init_mode (struct dwc3 *dwc) {struct device *dev = dwc->dev;
@@ -862,17 +1363,10 @@ static int dwc3_core_init_mode(struct dwc3 *dwc) }break ;case USB_DR_MODE_OTG : - ret =dwc3_host_init (dwc); -if (ret) { -if (ret != -EPROBE_DEFER ) -dev_err (dev,"failed to initialize host\n" ); -return ret; - } - - ret =dwc3_gadget_init (dwc); + ret =dwc3_drd_init (dwc);if (ret) {if (ret != -EPROBE_DEFER ) -dev_err (dev,"failed to initialize gadget\n" ); +dev_err (dev,"failed to initialize dual-role\n" );return ret; }break ;
@@ -894,8 +1388,7 @@ static void dwc3_core_exit_mode(struct dwc3 *dwc)dwc3_host_exit (dwc);break ;case USB_DR_MODE_OTG : -dwc3_host_exit (dwc); -dwc3_gadget_exit (dwc); +dwc3_drd_exit (dwc);break ;default :/* do nothing */
@@ -1207,19 +1700,35 @@ static int dwc3_suspend_common(struct dwc3 *dwc) {unsigned long flags; +spin_lock_irqsave (&dwc->lock, flags); +switch (dwc->dr_mode) {case USB_DR_MODE_PERIPHERAL : -case USB_DR_MODE_OTG : -spin_lock_irqsave (&dwc->lock, flags);dwc3_gadget_suspend (dwc); -spin_unlock_irqrestore (&dwc->lock, flags); +break ; +case USB_DR_MODE_OTG : +switch (dwc->otg_fsm.protocol) { +case PROTO_GADGET : +dwc3_gadget_suspend (dwc); +break ; +case PROTO_HOST : +case PROTO_UNDEF : +default : +/* nothing */ +break ; + }break ;case USB_DR_MODE_HOST : +case USB_DR_MODE_UNKNOWN :default :/* do nothing */ break ; } +if (dwc->dr_mode ==USB_DR_MODE_OTG ) +dwc3_otg_core_exit (dwc); + +spin_unlock_irqrestore (&dwc->lock, flags);dwc3_core_exit (dwc);return 0 ;
@@ -1234,19 +1743,40 @@ static int dwc3_resume_common(struct dwc3 *dwc)if (ret)return ret; +spin_lock_irqsave (&dwc->lock, flags); +switch (dwc->dr_mode) {case USB_DR_MODE_PERIPHERAL : -case USB_DR_MODE_OTG : -spin_lock_irqsave (&dwc->lock, flags);dwc3_gadget_resume (dwc); -spin_unlock_irqrestore (&dwc->lock, flags); -/* FALLTHROUGH */ +break ; +case USB_DR_MODE_OTG : +switch (dwc->otg_fsm.protocol) { +case PROTO_GADGET : +dwc3_gadget_resume (dwc); +break ; +case PROTO_HOST : +break ; +case PROTO_UNDEF : +default : +/* nothing */ +break ; + } +break ;case USB_DR_MODE_HOST : +case USB_DR_MODE_UNKNOWN :default :/* do nothing */ break ; } +if (dwc->dr_mode ==USB_DR_MODE_OTG ) { +dwc3_otg_core_init (dwc); +if (dwc->otg_fsm.protocol ==PROTO_HOST ) +dwc3_drd_start_host (dwc, true,1 ); + } + +spin_unlock_irqrestore (&dwc->lock, flags); +return 0 ; }
@@ -1301,6 +1831,7 @@ static int dwc3_runtime_resume(struct device *dev)dwc3_gadget_process_pending_events (dwc);break ;case USB_DR_MODE_HOST : +case USB_DR_MODE_UNKNOWN :default :/* do nothing */ break ;
@@ -1336,6 +1867,30 @@ static int dwc3_runtime_idle(struct device *dev)#endif /* CONFIG_PM */ #ifdef CONFIG_PM_SLEEP +static int dwc3_prepare (struct device *dev) +{ +struct dwc3 *dwc =dev_get_drvdata (dev); +unsigned long flags; + +spin_lock_irqsave (&dwc->lock, flags); + dwc->otg_prevent_sync = true; +spin_unlock_irqrestore (&dwc->lock, flags); + +return 0 ; +} + +static void dwc3_complete (struct device *dev) +{ +struct dwc3 *dwc =dev_get_drvdata (dev); +unsigned long flags; + +spin_lock_irqsave (&dwc->lock, flags); + dwc->otg_prevent_sync = false; +spin_unlock_irqrestore (&dwc->lock, flags); +if (dwc->dr_mode ==USB_DR_MODE_OTG ) +queue_work (system_power_efficient_wq, &dwc->otg_work); +} +static int dwc3_suspend (struct device *dev) {struct dwc3 *dwc =dev_get_drvdata (dev);
@@ -1373,6 +1928,10 @@ static const struct dev_pm_ops dwc3_dev_pm_ops = { SET_SYSTEM_SLEEP_PM_OPS(dwc3_suspend, dwc3_resume) SET_RUNTIME_PM_OPS(dwc3_runtime_suspend, dwc3_runtime_resume, dwc3_runtime_idle) +#ifdef CONFIG_PM_SLEEP + .prepare = dwc3_prepare, + .complete = dwc3_complete, +#endif };#ifdef CONFIG_OF
drivers/usb/dwc3/core.h +43 -1
102 lines not on this page · raw message
drivers/usb/dwc3/gadget.c +13 -5
@@ -1534,7 +1534,7 @@ static int dwc3_gadget_set_selfpowered(struct usb_gadget *g,return 0 ; } -static int dwc3_gadget_run_stop (struct dwc3 *dwc,int is_on,int suspend) +int dwc3_gadget_run_stop (struct dwc3 *dwc,int is_on,int suspend) {u32 reg;u32 timeout =500 ;
@@ -1542,6 +1542,10 @@ static int dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on, int suspend)if (pm_runtime_suspended (dwc->dev))return 0 ; +if (dwc->dr_mode ==USB_DR_MODE_OTG && + dwc->otg_fsm.protocol !=PROTO_GADGET ) +return 0 ; + reg =dwc3_readl (dwc->regs,DWC3_DCTL );if (is_on) {if (dwc->revision <=DWC3_REVISION_187A ) {
@@ -1603,6 +1607,7 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on) }spin_lock_irqsave (&dwc->lock, flags); + dwc->gadget_pullup = is_on; ret =dwc3_gadget_run_stop (dwc, is_on, false);spin_unlock_irqrestore (&dwc->lock, flags);
@@ -1679,7 +1684,7 @@ static void dwc3_gadget_setup_nump(struct dwc3 *dwc)dwc3_writel (dwc->regs,DWC3_DCFG , reg); } -static int __dwc3_gadget_start (struct dwc3 *dwc) +int __dwc3_gadget_start (struct dwc3 *dwc) {struct dwc3_ep *dep;int ret =0 ;
@@ -1812,8 +1817,11 @@ static int dwc3_gadget_start(struct usb_gadget *g, dwc->gadget_driver = driver; -if (pm_runtime_active (dwc->dev)) -__dwc3_gadget_start (dwc); +if (pm_runtime_active (dwc->dev)) { +if (!(dwc->dr_mode ==USB_DR_MODE_OTG && + dwc->otg_fsm.protocol !=PROTO_GADGET )) +__dwc3_gadget_start (dwc); + }spin_unlock_irqrestore (&dwc->lock, flags);
@@ -1827,7 +1835,7 @@ static int dwc3_gadget_start(struct usb_gadget *g,return ret; } -static void __dwc3_gadget_stop (struct dwc3 *dwc) +void __dwc3_gadget_stop (struct dwc3 *dwc) {dwc3_gadget_disable_irq (dwc);__dwc3_gadget_ep_disable (dwc->eps[0 ]);
Signature · 1 line
2.7.4
Re: [PATCH v2 3/4] usb: dwc3: add dual-role support
Hi,
Quoted 13 lines · Roger Quadros
If
dr_modeis "otg" then support dual role mode of operation.Get ID and VBUS information from the OTG controller and put the controller in the appropriate state.
This is our dual-role state table.
ID VBUS dual-role state
-- ---- ---------------
0 xA_HOST- Host controller active
1 0B_IDLE- Both Host and Gadget controllers inactive
1 1B_PERIPHERAL- Gadget controller active
Quoted 4 lines
Calling
dwc3_otg_fsm_sync()directly fromdwc3_complete()can lock up the system at xHCI add/remove so we use a work queue for it.Signed-off-by Roger Quadros <[email protected]>
it still seems to me that you're adding too much code for something that should be darn simple. Please, read on.
drivers/usb/dwc3/core.c line 30
Quoted 9 lines
drivers/usb/dwc3/core.c +1
-0@@ -27,6 +27,7 @@#include <linux/platform_device.h> #include <linux/pm_runtime.h> #include <linux/interrupt.h> +#include <linux/irq.h>
as a cosmetic change, it would be nicer to have a drd.c or otg.c which exposes dwc3_otg_start()/stop() like we do for gadget.c and host.c
Quoted 64 lines
drivers/usb/dwc3/core.c +53
-0@@ -107,6 +108,7 @@ void dwc3_set_mode(struct dwc3 *dwc, u32 mode) reg =dwc3_readl (dwc->regs,DWC3_GCTL ); reg &= ~(DWC3_GCTL_PRTCAPDIR (DWC3_GCTL_PRTCAP_OTG )); reg |=DWC3_GCTL_PRTCAPDIR (mode); + dwc->current_mode = mode;dwc3_writel (dwc->regs,DWC3_GCTL , reg); }@@ -839,6 +841,505 @@ static int dwc3_core_get_phy(struct dwc3 *dwc)return 0 ; } +static int dwc3_drd_start_host (struct dwc3 *dwc,int on,bool skip); +static int dwc3_drd_start_gadget (struct dwc3 *dwc,int on); + +/* dwc->lock must be held */ +static void dwc3_drd_statemachine (struct dwc3 *dwc,int id,int vbus) +{ +enum usb_otg_state new_state; +int protocol; + +if (id == dwc->otg_fsm.id && vbus == dwc->otg_fsm.b_sess_vld) +return ; + + dwc->otg_fsm.id = id; + dwc->otg_fsm.b_sess_vld = vbus; + +if (!id) { + new_state =OTG_STATE_A_HOST ; + }else { +if (vbus) + new_state =OTG_STATE_B_PERIPHERAL ; +else + new_state =OTG_STATE_B_IDLE ; + } + +if (dwc->otg.state == new_state) +return ; + + protocol = dwc->otg_fsm.protocol; +switch (new_state) { +case OTG_STATE_B_IDLE : +if (protocol ==PROTO_GADGET ) +dwc3_drd_start_gadget (dwc,0 ); +else if (protocol ==PROTO_HOST ) +dwc3_drd_start_host (dwc,0 ,0 ); + dwc->otg_fsm.protocol =PROTO_UNDEF ; +break ; +case OTG_STATE_B_PERIPHERAL : +if (protocol ==PROTO_HOST ) +dwc3_drd_start_host (dwc,0 ,0 ); + +if (protocol !=PROTO_GADGET ) { + dwc->otg_fsm.protocol =PROTO_GADGET ; +dwc3_drd_start_gadget (dwc,1 ); + } +break ; +case OTG_STATE_A_HOST : +if (protocol ==PROTO_GADGET ) +dwc3_drd_start_gadget (dwc,0 ); + +if (protocol !=PROTO_HOST ) { + dwc->otg_fsm.protocol =PROTO_HOST ; +dwc3_drd_start_host (dwc,1 ,0 );
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 905
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+ } +break ; +default : +dev_err (dwc->dev,"drd: invalid usb-drd state: %s\n" , +usb_otg_state_string (new_state)); +return ; + } + + dwc->otg.state = new_state; +}
I think I've mentioned this before. Why don't we start with the simplest possible implementation? Something that *just* allows us to get ID pin value and set the mode. After that's stable, then we add more pieces to the mix.
For something that simple, we wouldn't even need to use OTG FSM layer because that brings no benefit for such a simple requirement.
Once there's a *real* need for OTG FSM, then we can add support for it, but then we add support to something we know to be working.
Quoted 9 lines
drivers/usb/dwc3/core.c +9
-0+/* dwc->lock must be held */ +static void dwc3_otg_fsm_sync (struct dwc3 *dwc) +{ +u32 reg; +int id, vbus; + +/* +* calling dwc3_otg_fsm_sync() during resume breaks host +* if adapter was removed during suspend as xhci driver
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 925
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+* is not prepared to see hcd removal before xhci_resume. +*/ +if (dwc->otg_prevent_sync) +return ; + + reg =dwc3_readl (dwc->regs,DWC3_OSTS ); + id = !!(reg &DWC3_OSTS_CONIDSTS ); + vbus = !!(reg &DWC3_OSTS_BSESVLD ); +dwc3_drd_statemachine (dwc, id, vbus); +}
Just consider this for a moment. Consider the steps taken to get here.
- User plugs cable
- Hardirq handler run
- read register
- if (reg) return IRQ_WAKE_THREAD;
- schedule bottom half handler to sometime in the future
- scheduler runs our threaded handler
- lock dwc3
- if (host)
- configure register
- add xHCI device
- else
- otg_fsm_sync()
- drd_statemachine()
- configure registers
- reimplement gadget initialization (same thing we do when registering UDC
I mean, just looking at this we can already see that it's really overly complex. Right now we need simple, dead simple. This will limit the possibility of errors.
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 935
Quoted 9 lines
drivers/usb/dwc3/core.c +9
-0+static void dwc3_drd_work (struct work_struct *work) +{ + struct dwc3 *dwc = container_of(work, struct dwc3, + otg_work); + +spin_lock (&dwc->lock); +dwc3_otg_fsm_sync (dwc); +spin_unlock (&dwc->lock); +}
so this is only called from ->complete(). You mentioned your commit log that calling dwc3_otg_fsm_sync() directly from ->complete() can lock up the system. Why? I have a feeling your locking isn't proper and that's why sometimes it locks up. You introduced a deadlock and to work around it, the "solution" was to add a workqueue.
Can you either confirm or refute the statement above?
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 941
Quoted 5 lines
drivers/usb/dwc3/core.c +5
-0+static void dwc3_otg_disable_events (struct dwc3 *dwc,u32 disable_mask) +{ + dwc->oevten &= ~(disable_mask); +dwc3_writel (dwc->regs,DWC3_OEVTEN , dwc->oevten); +}
we should disable OTG events from our top half handler, otherwise top and bottom half can race with each other.
Quoted 17 lines
drivers/usb/dwc3/core.c +17
-0+static void dwc3_otg_enable_events (struct dwc3 *dwc,u32 enable_mask) +{ + dwc->oevten |= (enable_mask); +dwc3_writel (dwc->regs,DWC3_OEVTEN , dwc->oevten); +} + +#define DWC3_OTG_ALL_EVENTS (DWC3_OEVTEN_XHCIRUNSTPSETEN | \ + DWC3_OEVTEN_DEVRUNSTPSETEN | DWC3_OEVTEN_HIBENTRYEN | \ + DWC3_OEVTEN_CONIDSTSCHNGEN | DWC3_OEVTEN_HRRCONFNOTIFEN | \ + DWC3_OEVTEN_HRRINITNOTIFEN | DWC3_OEVTEN_ADEVIDLEEN | \ + DWC3_OEVTEN_ADEVBHOSTENDEN | DWC3_OEVTEN_ADEVHOSTEN | \ + DWC3_OEVTEN_ADEVHNPCHNGEN | DWC3_OEVTEN_ADEVSRPDETEN | \ + DWC3_OEVTEN_ADEVSESSENDDETEN | DWC3_OEVTEN_BDEVHOSTENDEN | \ + DWC3_OEVTEN_BDEVHNPCHNGEN | DWC3_OEVTEN_BDEVSESSVLDDETEN | \ + DWC3_OEVTEN_BDEVVBUSCHNGE) + +static irqreturn_t dwc3_otg_thread_irq (int irq,void *_dwc)
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 969
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+{ +struct dwc3 *dwc = _dwc; + +spin_lock (&dwc->lock); +if (dwc->otg_needs_host_start) { +dwc3_drd_start_host (dwc, true,1 ); + dwc->otg_needs_host_start =0 ; + } + +dwc3_otg_fsm_sync (dwc);
enable_events();
Quoted 8 lines
drivers/usb/dwc3/core.c +8
-0+spin_unlock (&dwc->lock); + +return IRQ_HANDLED ; +} + +static irqreturn_t dwc3_otg_irq (int irq,void *_dwc) +{ +u32 reg;
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 987
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+struct dwc3 *dwc = _dwc; +irqreturn_t ret =IRQ_NONE ; + + reg =dwc3_readl (dwc->regs,DWC3_OEVT ); +if (reg) { +if ((dwc->otg_fsm.protocol ==PROTO_HOST ) && + !(reg &DWC3_OEVT_DEVICEMODE )) + dwc->otg_needs_host_start =1 ; +dwc3_writel (dwc->regs,DWC3_OEVT , reg); + ret =IRQ_WAKE_THREAD ;
disable_events();
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 984
Quoted 1 line
drivers/usb/dwc3/core.c +1
-0+ }
There's one step missing here. Where do you mask OTG interrupts?
Quoted 13 lines
drivers/usb/dwc3/core.c +13
-0+ +return ret; +} + +/* --------------------- Dual-Role management ------------------------------- */ +static void dwc3_otgregs_init (struct dwc3 *dwc) +{ +u32 reg; + +/* +* Prevent host/device reset from resetting OTG core. +* If we don't do this then xhci_reset (USBCMD.HCRST) will reset +* the signal outputs sent to the PHY, the OTG FSM logic of the
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1011
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+* core and also the resets to the VBUS filters inside the core. +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg |=DWC3_OCFG_SFTRSTMASK ; +dwc3_writel (dwc->regs,DWC3_OCFG , reg); + +/* Disable hibernation for simplicity */ + reg =dwc3_readl (dwc->regs,DWC3_GCTL ); + reg &= ~DWC3_GCTL_GBLHIBERNATIONEN ; +dwc3_writel (dwc->regs,DWC3_GCTL , reg);
no, don't do that. We support hibernation on some Intel devices. You'd be regressing them, most likely.
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1019
Quoted 7 lines
drivers/usb/dwc3/core.c +7
-0+/* +* Initialize OTG registers as per +* Figure 11-4 OTG Driver Overall Programming Flow +*/ +/* OCFG.SRPCap = 0, OCFG.HNPCap = 0 */ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~(DWC3_OCFG_SRPCAP |DWC3_OCFG_HNPCAP );
are you sure *NO* DWC3 implementation out there is SRP capable and HNP capable?
HNP I understand that you want to disable because we're not support full OTG, but SRP should be easy to support and it's also rather handy. In any case, perhaps add a slightly longer comment explaining why you're disabling these?
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1022
Quoted 3 lines
drivers/usb/dwc3/core.c +3
-0+dwc3_writel (dwc->regs,DWC3_OCFG , reg); +/* OEVT = FFFF */ +dwc3_writel (dwc->regs,DWC3_OEVT , ~0 );
hmmm, flushing pending events. Are you sure you can even have them at this point? This should be called after we reset the controller.
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1026
Quoted 4 lines
drivers/usb/dwc3/core.c +4
-0+/* OEVTEN = 0 */ +dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS ); +/* OEVTEN.ConIDStsChngEn = 1. Instead we enable all events */ +dwc3_otg_enable_events (dwc,DWC3_OTG_ALL_EVENTS );
oh, disable everything and enable everything right after. What gives?
Quoted 12 lines
drivers/usb/dwc3/core.c +12
-0+/* +* OCTL.PeriMode = 1, OCTL.DevSetHNPEn = 0, OCTL.HstSetHNPEn = 0, +* OCTL.HNPReq = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg |=DWC3_OCTL_PERIMODE ; + reg &= ~(DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HSTSETHNPEN | +DWC3_OCTL_HNPREQ ); +dwc3_writel (dwc->regs,DWC3_OCTL , reg); +} + +/* dwc->lock must be held */
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1048
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+static int dwc3_drd_start_host (struct dwc3 *dwc,int on,bool skip) +{ +u32 reg; + +/* switch OTG core */ +if (on) { +/* As per Figure 11-10 A-Device Flow Diagram */ +/* OCFG.HNPCap = 0, OCFG.SRPCap = 0 */ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~(DWC3_OCFG_SRPCAP |DWC3_OCFG_HNPCAP );
didn't you do this already? Why do you need to do this again?
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1057
Quoted 9 lines
drivers/usb/dwc3/core.c +9
-0+dwc3_writel (dwc->regs,DWC3_OCFG , reg); + +/* +* OCTL.PeriMode=0, OCTL.TermSelDLPulse = 0, +* OCTL.DevSetHNPEn = 0, OCTL.HstSetHNPEn = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg &= ~(DWC3_OCTL_PERIMODE |DWC3_OCTL_TERMSELIDPULSE | +DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HSTSETHNPEN );
HNP already disabled elsewhere. Why disable it again?
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1064
Quoted 7 lines
drivers/usb/dwc3/core.c +7
-0+dwc3_writel (dwc->regs,DWC3_OCTL , reg); + +/* +* OCFG.DisPrtPwrCutoff = 0/1 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~DWC3_OCFG_DISPWRCUTTOFF ;
^^ one T enough?
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1060
Quoted 1 line
drivers/usb/dwc3/core.c +1
-0+dwc3_writel (dwc->regs,DWC3_OCFG , reg);
should you really always disable port power cutoff ?
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1062
Quoted 2 lines
drivers/usb/dwc3/core.c +2
-0+/* start the xHCI host driver */ +if (!skip) {
when would skip be true?
Quoted 12 lines
drivers/usb/dwc3/core.c +12
-0+spin_unlock (&dwc->lock); +dwc3_host_init (dwc); +spin_lock (&dwc->lock); + } + +/* +* OCFG.SRPCap = 1, OCFG.HNPCap = GHWPARAMS6.HNP_CAP +* We don't want SRP/HNP for simple dual-role so leave +* these disabled. +*/ + +/*
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1090
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+* OEVTEN.OTGADevHostEvntEn = 1 +* OEVTEN.OTGADevSessEndDetEvntEn = 1 +* We don't want HNP/role-swap so leave these disabled. +*/ + +/* GUSB2PHYCFG.ULPIAutoRes = 1/0, GUSB2PHYCFG.SusPHY = 1 */ +if (!dwc->dis_u2_susphy_quirk) { + reg =dwc3_readl (dwc->regs,DWC3_GUSB2PHYCFG (0 )); + reg |=DWC3_GUSB2PHYCFG_SUSPHY ; +dwc3_writel (dwc->regs,DWC3_GUSB2PHYCFG (0 ), reg);
already done elsewhere. Why do you need to do it again?
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1096
Quoted 6 lines
drivers/usb/dwc3/core.c +6
-0+ } + +/* Set Port Power to enable VBUS: OCTL.PrtPwrCtl = 1 */ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg |=DWC3_OCTL_PRTPWRCTL ; +dwc3_writel (dwc->regs,DWC3_OCTL , reg);
I wonder if you have a race here with xHCI. You're essentially enable port power after xHCI has been loaded already. Mathias, do you see any problems with this? Could we confuse xHCI with this? I'm assuming there are no issues since without VBUS xHCI wouldn't see any port status change events, but thought I'd ask anyway.
Quoted 7 lines
drivers/usb/dwc3/core.c +7
-0+ }else { +/* +* Exit from A-device flow as per +* Figure 11-4 OTG Driver Overall Programming Flow +*/ +/* stop the HCD */ +if (!skip) {
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1113
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+spin_unlock (&dwc->lock); +dwc3_host_exit (dwc); +spin_lock (&dwc->lock); + } + +/* +* OEVTEN.OTGADevBHostEndEvntEn=0, OEVTEN.OTGADevHNPChngEvntEn=0 +* OEVTEN.OTGADevSessEndDetEvntEn=0, +* OEVTEN.OTGADevHostEvntEn = 0 +* But we don't disable any OTG events
why not?
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1118
Quoted 5 lines
drivers/usb/dwc3/core.c +5
-0+*/ + +/* OCTL.HstSetHNPEn = 0, OCTL.PrtPwrCtl=0 */ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg &= ~(DWC3_OCTL_HSTSETHNPEN |DWC3_OCTL_PRTPWRCTL );
disabled elsewhere. Why do it again?
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1122
Quoted 4 lines
drivers/usb/dwc3/core.c +4
-0+dwc3_writel (dwc->regs,DWC3_OCTL , reg); + +/* Initialize OTG registers */ +dwc3_otgregs_init (dwc);
again you reinitialize everything. Why so many reinitializations? Seems like you were having issues getting this to work and ended up with silly reinitializations and workqueues in an effort to get it working.
This patch gives me the impression that the feature hasn't been tested properly. :-s
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1136
Quoted 9 lines
drivers/usb/dwc3/core.c +9
-0+/* dwc->lock must be held */ +static int dwc3_drd_start_gadget (struct dwc3 *dwc,int on) +{ +u32 reg; + +if (on) +dwc3_event_buffers_setup (dwc); + +if (on) {
if (on)
[..]
if (on)
[..]
:-s
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1144
Quoted 6 lines
drivers/usb/dwc3/core.c +6
-0+/* +* OCFG.HNPCap = GHWPARAMS6.HNP_CAP, OCFG.SRPCap = 1 +* but we set them to 0 for simple dual-role operation. +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~(DWC3_OCFG_SRPCAP |DWC3_OCFG_HNPCAP );
and again clearing bits that have already been cleared multiple times.
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1146
Quoted 2 lines
drivers/usb/dwc3/core.c +2
-0+/* OCFG.OTGSftRstMsk = 0/1 */ + reg |=DWC3_OCFG_SFTRSTMASK ;
do you need to set this again?
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1156
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+dwc3_writel (dwc->regs,DWC3_OCFG , reg); +/* +* OCTL.PeriMode = 1 +* OCTL.TermSelDLPulse = 0/1, OCTL.HNPReq = 0 +* OCTL.DevSetHNPEn = 0, OCTL.HstSetHNPEn = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg |=DWC3_OCTL_PERIMODE ; + reg &= ~(DWC3_OCTL_TERMSELIDPULSE |DWC3_OCTL_HNPREQ | +DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HSTSETHNPEN );
clearing bits that were already cleared.
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1168
Quoted 12 lines
drivers/usb/dwc3/core.c +12
-0+dwc3_writel (dwc->regs,DWC3_OCTL , reg); +/* OEVTEN.OTGBDevSesVldDetEvntEn = 1 */ +dwc3_otg_enable_events (dwc,DWC3_OEVT_BDEVSESSVLDDET ); +/* GUSB2PHYCFG.ULPIAutoRes = 0, GUSB2PHYCFG0.SusPHY = 1 */ +if (!dwc->dis_u2_susphy_quirk) { + reg =dwc3_readl (dwc->regs,DWC3_GUSB2PHYCFG (0 )); + reg |=DWC3_GUSB2PHYCFG_SUSPHY ; +dwc3_writel (dwc->regs,DWC3_GUSB2PHYCFG (0 ), reg); + } +/* GCTL.GblHibernationEn = 0 */ + reg =dwc3_readl (dwc->regs,DWC3_GCTL ); + reg &= ~DWC3_GCTL_GBLHIBERNATIONEN ;
possibly breaking other users.
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1175
Quoted 7 lines
drivers/usb/dwc3/core.c +7
-0+dwc3_writel (dwc->regs,DWC3_GCTL , reg); + +/* start the Peripheral driver */ +if (dwc->gadget_driver) { +__dwc3_gadget_start (dwc); +if (dwc->gadget_pullup) +dwc3_gadget_run_stop (dwc, true, false);
why don't you add/remove the UDC just like you do for the HCD? (you wouldn't add/remove a device, but rather call usb_del_gadget_udc()/usb_add_gadget_udc() directly. Would that clean up some of this?
Quoted 5 lines
drivers/usb/dwc3/core.c +5
-0+ } + }else { +/* +* Exit from B-device flow as per +* Figure 11-4 OTG Driver Overall Programming Flow
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1190
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+*/ +/* stop the Peripheral driver */ +if (dwc->gadget_driver) { +if (dwc->gadget_pullup) +dwc3_gadget_run_stop (dwc, false, false); +spin_unlock (&dwc->lock); +if (dwc->gadget_driver->disconnect) + dwc->gadget_driver->disconnect (&dwc->gadget); +spin_lock (&dwc->lock); +__dwc3_gadget_stop (dwc);
usb_del_gadget_udc()
Quoted 5 lines
drivers/usb/dwc3/core.c +5
-0+ } + +/* +* OEVTEN.OTGBDevHNPChngEvntEn = 0 +* OEVTEN.OTGBDevVBusChngEvntEn = 0
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1205
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+* OEVTEN.OTGBDevBHostEndEvntEn = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OEVTEN ); + reg &= ~(DWC3_OEVT_BDEVHNPCHNG |DWC3_OEVT_BDEVVBUSCHNG | +DWC3_OEVT_BDEVBHOSTEND ); +dwc3_writel (dwc->regs,DWC3_OEVTEN , reg); + +/* OCTL.DevSetHNPEn = 0, OCTL.HNPReq = 0, OCTL.PeriMode=1 */ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg &= ~(DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HNPREQ );
:-)
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1210
Quoted 5 lines
drivers/usb/dwc3/core.c +5
-0+ reg |=DWC3_OCTL_PERIMODE ; +dwc3_writel (dwc->regs,DWC3_OCTL , reg); + +/* Initialize OTG registers */ +dwc3_otgregs_init (dwc);
:-)
Quoted 37 lines
drivers/usb/dwc3/core.c +37
-0+static int dwc3_otg_get_irq (struct dwc3 *dwc) +{ +struct platform_device *dwc3_pdev =to_platform_device (dwc->dev); +int irq; + + irq =platform_get_irq_byname (dwc3_pdev,"otg" ); +if (irq >0 ) + goto out; + +if (irq == -EPROBE_DEFER ) + goto out; + + irq =platform_get_irq_byname (dwc3_pdev,"dwc_usb3" ); +if (irq >0 ) + goto out; + +if (irq == -EPROBE_DEFER ) + goto out; + + irq =platform_get_irq (dwc3_pdev,0 ); +if (irq >0 ) + goto out; + +if (irq != -EPROBE_DEFER ) +dev_err (dwc->dev,"missing otg IRQ\n" ); + +if (!irq) + irq = -EINVAL ; + +out: +return irq; +} + +/* dwc->lock must be held */ +static void dwc3_otg_core_init (struct dwc3 *dwc) +{ +u32 reg;
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1262
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+ +/* +* As per Figure 11-4 OTG Driver Overall Programming Flow, +* block "Initialize GCTL for OTG operation". +*/ +/* GCTL.PrtCapDir=2'b11 */ +dwc3_set_mode (dwc,DWC3_GCTL_PRTCAP_OTG ); +/* GUSB2PHYCFG0.SusPHY=0 */ + reg =dwc3_readl (dwc->regs,DWC3_GUSB2PHYCFG (0 )); + reg &= ~DWC3_GUSB2PHYCFG_SUSPHY ;
why here? We only need this if the quirk flag is set. If that flag has been set, this bit should have been cleared already.
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1270
Quoted 8 lines
drivers/usb/dwc3/core.c +8
-0+dwc3_writel (dwc->regs,DWC3_GUSB2PHYCFG (0 ), reg); + +/* Initialize OTG registers */ +dwc3_otgregs_init (dwc); + +/* force drd state machine update the first time */ + dwc->otg_fsm.b_sess_vld =-1 ; + dwc->otg_fsm.id =-1 ;
Does this work if you boot with cable already attached? Both host and peripheral cables?
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1279
Quoted 9 lines
drivers/usb/dwc3/core.c +9
-0+} + +/* dwc->lock must be held */ +static void dwc3_otg_core_exit (struct dwc3 *dwc) +{ +/* disable all otg irqs */ +dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS ); +/* clear all events */ +dwc3_writel (dwc->regs,DWC3_OEVT , ~0 );
when free_irq() is called, it will wait for the current interrupt to finish being processed, this means OEVT will already be zero but the time free_irq() finishes running. I think you shouldn't care about this.
Just mask all events and that should be enough.
Quoted 7 lines
drivers/usb/dwc3/core.c +7
-0+static int dwc3_drd_init (struct dwc3 *dwc) +{ +int ret, irq; +unsigned long flags; + +INIT_WORK (&dwc->otg_work, dwc3_drd_work); +
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1298
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+ irq =dwc3_otg_get_irq (dwc); +if (irq <0 ) +return irq; + + dwc->otg_irq = irq; + +/* disable all otg irqs */ +dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS ); +/* clear all events */ +dwc3_writel (dwc->regs,DWC3_OEVT , ~0 );
this is really odd. You have a bunch of these duplicated chunks of code all over the place...
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1300
Quoted 1 line
drivers/usb/dwc3/core.c +1
-0+irq_set_status_flags (dwc->otg_irq,IRQ_NOAUTOEN );
why?
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1311
Quoted 11 lines
drivers/usb/dwc3/core.c +11
-0+ ret =request_threaded_irq (dwc->otg_irq, dwc3_otg_irq, + dwc3_otg_thread_irq, +IRQF_SHARED ,"dwc3-otg" , dwc); +if (ret) { +dev_err (dwc->dev,"failed to request irq #%d --> %d\n" , + dwc->otg_irq, ret); + ret = -ENODEV ; +return ret; + } + + ret =dwc3_gadget_init (dwc);
unconditionally? What if I booted with a micro-A plugged to my port and a USB-stick attached to it?
I think this should be conditional on extcon cable state.
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1320
Quoted 9 lines
drivers/usb/dwc3/core.c +9
-0+if (ret) { +free_irq (dwc->otg_irq, dwc); +return ret; + } + +spin_lock_irqsave (&dwc->lock, flags); +dwc3_otg_core_init (dwc); +spin_unlock_irqrestore (&dwc->lock, flags); +queue_work (system_power_efficient_wq, &dwc->otg_work);
:-s
Quoted 4 lines
drivers/usb/dwc3/core.c +4
-0+return 0 ; +} + +static void dwc3_drd_exit (struct dwc3 *dwc)
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1335
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+{ +unsigned long flags; + +cancel_work_sync (&dwc->otg_work); +spin_lock_irqsave (&dwc->lock, flags); +dwc3_otg_core_exit (dwc); +if (dwc->otg_fsm.protocol ==PROTO_HOST ) +dwc3_drd_start_host (dwc,0 ,0 ); + dwc->otg_fsm.protocol =PROTO_UNDEF ; +free_irq (dwc->otg_irq, dwc);
free_irq() might sleep, no?
/**
* free_irq - free an interrupt allocated with request_irq
* @irq: Interrupt line to free
* @dev_id: Device identity to free
*
* Remove an interrupt handler. The handler is removed and if the
* interrupt line is no longer in use by any driver it is disabled.
* On a shared IRQ the caller must ensure the interrupt is disabled
* on the card it drives before calling this function. The function
* does not return until any executing interrupts for this IRQ
* have completed.
*
* This function must not be called from interrupt context.
*/
void free_irq(unsigned int irq, void *dev_id)
drivers/usb/dwc3/core.c static int dwc3_suspend_common(struct dwc3 *dwc) · line 1703
Quoted 5 lines
drivers/usb/dwc3/core.c +1
-0@@ -1207,19 +1700,35 @@ static int dwc3_suspend_common(struct dwc3 *dwc) {unsigned long flags; +spin_lock_irqsave (&dwc->lock, flags);
looks like it should be in a separate patch.
Quoted 10 lines
drivers/usb/dwc3/core.c +1
-1@@ -1679,7 +1684,7 @@ static void dwc3_gadget_setup_nump(struct dwc3 *dwc)dwc3_writel (dwc->regs,DWC3_DCFG , reg); } -static int __dwc3_gadget_start (struct dwc3 *dwc) +int __dwc3_gadget_start (struct dwc3 *dwc) {struct dwc3_ep *dep;int ret =0 ;
drivers/usb/dwc3/core.c static int dwc3_gadget_start(struct usb_gadget *g, · line 1838
Quoted 5 lines
drivers/usb/dwc3/core.c +1
-1@@ -1827,7 +1835,7 @@ static int dwc3_gadget_start(struct usb_gadget *g,return ret; } -static void __dwc3_gadget_stop (struct dwc3 *dwc) +void __dwc3_gadget_stop (struct dwc3 *dwc)
shouldn't have to. Just rely on usb_add/del_gadget_udc()
Signature · 1 line
balbi
Re: [PATCH v2 3/4] usb: dwc3: add dual-role support
Hi,
Quoted 17 lines · Felipe Balbi
Hi,
Quoted 13 lines · Roger Quadros
If
dr_modeis "otg" then support dual role mode of operation.Get ID and VBUS information from the OTG controller and put the controller in the appropriate state.
This is our dual-role state table.
ID VBUS dual-role state
-- ---- ---------------
0 xA_HOST- Host controller active
1 0B_IDLE- Both Host and Gadget controllers inactive
1 1B_PERIPHERAL- Gadget controller active
Quoted 7 lines
Quoted 4 lines
Calling
dwc3_otg_fsm_sync()directly fromdwc3_complete()can lock up the system at xHCI add/remove so we use a work queue for it.Signed-off-by Roger Quadros <[email protected]>it still seems to me that you're adding too much code for something that should be darn simple. Please, read on.
Sure, I'm all ears for simplification :).
Quoted 13 lines
drivers/usb/dwc3/core.c line 30
Quoted 10 lines
drivers/usb/dwc3/core.c +1
-0@@ -27,6 +27,7 @@#include <linux/platform_device.h> #include <linux/pm_runtime.h> #include <linux/interrupt.h> +#include <linux/irq.h> as a cosmetic change, it would be nicer to have a
drd.corotg.cwhich exposes dwc3_otg_start()/stop() like we do forgadget.candhost.c
Agreed.
Quoted 72 lines
Quoted 72 lines
drivers/usb/dwc3/core.c +60
-0@@ -107,6 +108,7 @@ void dwc3_set_mode(struct dwc3 *dwc, u32 mode) reg =dwc3_readl (dwc->regs,DWC3_GCTL ); reg &= ~(DWC3_GCTL_PRTCAPDIR (DWC3_GCTL_PRTCAP_OTG )); reg |=DWC3_GCTL_PRTCAPDIR (mode); + dwc->current_mode = mode;dwc3_writel (dwc->regs,DWC3_GCTL , reg); }@@ -839,6 +841,505 @@ static int dwc3_core_get_phy(struct dwc3 *dwc)return 0 ; } +static int dwc3_drd_start_host (struct dwc3 *dwc,int on,bool skip); +static int dwc3_drd_start_gadget (struct dwc3 *dwc,int on); + +/* dwc->lock must be held */ +static void dwc3_drd_statemachine (struct dwc3 *dwc,int id,int vbus) +{ +enum usb_otg_state new_state; +int protocol; + +if (id == dwc->otg_fsm.id && vbus == dwc->otg_fsm.b_sess_vld) +return ; + + dwc->otg_fsm.id = id; + dwc->otg_fsm.b_sess_vld = vbus; + +if (!id) { + new_state =OTG_STATE_A_HOST ; + }else { +if (vbus) + new_state =OTG_STATE_B_PERIPHERAL ; +else + new_state =OTG_STATE_B_IDLE ; + } + +if (dwc->otg.state == new_state) +return ; + + protocol = dwc->otg_fsm.protocol; +switch (new_state) { +case OTG_STATE_B_IDLE : +if (protocol ==PROTO_GADGET ) +dwc3_drd_start_gadget (dwc,0 ); +else if (protocol ==PROTO_HOST ) +dwc3_drd_start_host (dwc,0 ,0 ); + dwc->otg_fsm.protocol =PROTO_UNDEF ; +break ; +case OTG_STATE_B_PERIPHERAL : +if (protocol ==PROTO_HOST ) +dwc3_drd_start_host (dwc,0 ,0 ); + +if (protocol !=PROTO_GADGET ) { + dwc->otg_fsm.protocol =PROTO_GADGET ; +dwc3_drd_start_gadget (dwc,1 ); + } +break ; +case OTG_STATE_A_HOST : +if (protocol ==PROTO_GADGET ) +dwc3_drd_start_gadget (dwc,0 ); + +if (protocol !=PROTO_HOST ) { + dwc->otg_fsm.protocol =PROTO_HOST ; +dwc3_drd_start_host (dwc,1 ,0 ); + } +break ; +default : +dev_err (dwc->dev,"drd: invalid usb-drd state: %s\n" , +usb_otg_state_string (new_state)); +return ; + }
Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 905
Quoted 3 lines
drivers/usb/dwc3/core.c +3
-0+ + dwc->otg.state = new_state; +}I think I've mentioned this before. Why don't we start with the simplest possible implementation? Something that *just* allows us to get ID pin value and set the mode. After that's stable, then we add more pieces to the mix.
That is exactly what I'm doing. Maybe the switch case is making it look complicated. dwc3_drd_statemachine() has only 2 inputs VBUS and ID.
I can change it to if/else if you prefer that. I like the way it is cause we can define 3 states IDLE, PERIPHERAL and HOST.
Quoted 3 lines
For something that simple, we wouldn't even need to use OTG FSM layer because that brings no benefit for such a simple requirement.
no no. I think you got it wrong. I'm not using the OTG FSM layer at all :).
Quoted 43 lines
Once there's a *real* need for OTG FSM, then we can add support for it, but then we add support to something we know to be working.
Quoted 9 lines
drivers/usb/dwc3/core.c +9
-0+/* dwc->lock must be held */ +static void dwc3_otg_fsm_sync (struct dwc3 *dwc) +{ +u32 reg; +int id, vbus; + +/* +* calling dwc3_otg_fsm_sync() during resume breaks host +* if adapter was removed during suspend as xhci driver drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 925
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+* is not prepared to see hcd removal before xhci_resume. +*/ +if (dwc->otg_prevent_sync) +return ; + + reg =dwc3_readl (dwc->regs,DWC3_OSTS ); + id = !!(reg &DWC3_OSTS_CONIDSTS ); + vbus = !!(reg &DWC3_OSTS_BSESVLD ); +dwc3_drd_statemachine (dwc, id, vbus); +}Just consider this for a moment. Consider the steps taken to get here.
- User plugs cable
- Hardirq handler run
- read register
- if (reg) returnIRQ_WAKE_THREAD;
- schedule bottom half handler to sometime in the future
- scheduler runs our threaded handler
- lock dwc3
- if (host)
- configure register
- add xHCI device
- else
-otg_fsm_sync()
-drd_statemachine()
- configure registers
- reimplement gadget initialization (same thing we do when registering UDC
Quoted 3 lines
I mean, just looking at this we can already see that it's really overly complex. Right now we need simple, dead simple. This will limit the possibility of errors.
OK. I can probably get rid of the state machine model and just use if/else? Anything else you want me to get rid of?
Quoted 17 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 935
Quoted 10 lines
drivers/usb/dwc3/core.c +9
-0+static void dwc3_drd_work (struct work_struct *work) +{ + struct dwc3 *dwc = container_of(work, struct dwc3, + otg_work); + +spin_lock (&dwc->lock); +dwc3_otg_fsm_sync (dwc); +spin_unlock (&dwc->lock); +}so this is only called from ->complete(). You mentioned your commit log that calling
dwc3_otg_fsm_sync()directly from ->complete() can lock up the system. Why? I have a feeling your locking isn't proper and that's why sometimes it locks up. You introduced a deadlock and to work around it, the "solution" was to add a workqueue.
Quoted 1 line
Can you either confirm or refute the statement above?
The real problem was that if host adapter was removed during a system suspend then while resuming XHCI was locking up like below. This is probably because we're trying to remove/Halt the HCD in the otg_irq_handler before XHCI driver has resumed?
How can we ensure that we call dwc3_host_exit() only *after* XHCI driver has resumed?
[ 1057.565573] PM: Syncing filesystems ... done. [ 1057.573986] PM: Preparing system for sleep (mem) [ 1057.580282] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 1057.589626] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 1057.598931] PM: Suspending system (mem) [ 1057.617852] PM: suspend of devices complete after 13.163 msecs [ 1057.628279] PM: late suspend of devices complete after 4.296 msecs [ 1057.635858] PM: noirq resume of devices complete after 0.178 msecs [ 1057.642783] PM: noirq suspend of devices failed [ 1057.649703] PM: early resume of devices complete after 2.134 msecs [ 1057.658046] net eth0: initializing cpsw version 1.15 (0) [ 1057.663634] cpsw 48484000.ethernet: initialized cpsw ale version 1.4 [ 1057.670325] cpsw 48484000.ethernet: ALE Table size 1024 [ 1057.683322] Generic PHY 48485000.mdio:02: attached PHY driver [Generic PHY] (mii_bus:phy_addr=48485000.mdio:02, irq=-1) [ 1057.706453] usb usb1: root hub lost power or was reset [ 1057.711847] usb usb2: root hub lost power or was reset [ 1057.987078] ata1: SATA link down (SStatus 0 SControl 300) [ 1059.762288] cpsw 48484000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[ 1061.846695] PM: resume of devices complete after 4190.473 msecs [ 1061.853294] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 1061.858644] usb usb2: USB disconnect, device number 1 [ 1061.890701] xhci-hcd xhci-hcd.0.auto: Host halt failed, -110 [ 1061.896640] xhci-hcd xhci-hcd.0.auto: Host controller not halted, aborting reset. [ 1061.904535] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered [ 1061.910514] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 1061.915848] usb usb1: USB disconnect, device number 1 [ 1061.921146] usb 1-1: USB disconnect, device number 2
Quoted 9 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 941
Quoted 6 lines
drivers/usb/dwc3/core.c +5
-0+static void dwc3_otg_disable_events (struct dwc3 *dwc,u32 disable_mask) +{ + dwc->oevten &= ~(disable_mask); +dwc3_writel (dwc->regs,DWC3_OEVTEN , dwc->oevten); +}we should disable OTG events from our top half handler, otherwise top and bottom half can race with each other.
If we disable OTG events then there is a chance that we miss the events that happen while they were disabled.
We need a way to mask the OTG events without loosing them while they are masked. Do you know how that could be achieved?
Quoted 43 lines
Quoted 18 lines
drivers/usb/dwc3/core.c +17
-0+static void dwc3_otg_enable_events (struct dwc3 *dwc,u32 enable_mask) +{ + dwc->oevten |= (enable_mask); +dwc3_writel (dwc->regs,DWC3_OEVTEN , dwc->oevten); +} + +#define DWC3_OTG_ALL_EVENTS (DWC3_OEVTEN_XHCIRUNSTPSETEN | \ + DWC3_OEVTEN_DEVRUNSTPSETEN | DWC3_OEVTEN_HIBENTRYEN | \ + DWC3_OEVTEN_CONIDSTSCHNGEN | DWC3_OEVTEN_HRRCONFNOTIFEN | \ + DWC3_OEVTEN_HRRINITNOTIFEN | DWC3_OEVTEN_ADEVIDLEEN | \ + DWC3_OEVTEN_ADEVBHOSTENDEN | DWC3_OEVTEN_ADEVHOSTEN | \ + DWC3_OEVTEN_ADEVHNPCHNGEN | DWC3_OEVTEN_ADEVSRPDETEN | \ + DWC3_OEVTEN_ADEVSESSENDDETEN | DWC3_OEVTEN_BDEVHOSTENDEN | \ + DWC3_OEVTEN_BDEVHNPCHNGEN | DWC3_OEVTEN_BDEVSESSVLDDETEN | \ + DWC3_OEVTEN_BDEVVBUSCHNGE) + +static irqreturn_t dwc3_otg_thread_irq (int irq,void *_dwc)drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 969
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+{ +struct dwc3 *dwc = _dwc; + +spin_lock (&dwc->lock); +if (dwc->otg_needs_host_start) { +dwc3_drd_start_host (dwc, true,1 ); + dwc->otg_needs_host_start =0 ; + } + +dwc3_otg_fsm_sync (dwc);
enable_events();Quoted 12 lines
drivers/usb/dwc3/core.c +12
-0+spin_unlock (&dwc->lock); + +return IRQ_HANDLED ; +} + +static irqreturn_t dwc3_otg_irq (int irq,void *_dwc) +{ +u32 reg; +struct dwc3 *dwc = _dwc; +irqreturn_t ret =IRQ_NONE ; + + reg =dwc3_readl (dwc->regs,DWC3_OEVT );
Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 987
Quoted 6 lines
drivers/usb/dwc3/core.c +6
-0+if (reg) { +if ((dwc->otg_fsm.protocol ==PROTO_HOST ) && + !(reg &DWC3_OEVT_DEVICEMODE )) + dwc->otg_needs_host_start =1 ; +dwc3_writel (dwc->regs,DWC3_OEVT , reg); + ret =IRQ_WAKE_THREAD ;
disable_events();
We can't disable events if we don't want to miss any events while they were disabled. But I agree that we need to prevent them from firing another hard IRQ. I couldn't figure out how that can be done.
Quoted 4 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 984
Quoted 2 lines
drivers/usb/dwc3/core.c +1
-0+ }There's one step missing here. Where do you mask OTG interrupts?
What is the way to mask OTG interrupts without loosing them.
Quoted 19 lines
Quoted 19 lines
drivers/usb/dwc3/core.c +18
-0+ +return ret; +} + +/* --------------------- Dual-Role management ------------------------------- */ +static void dwc3_otgregs_init (struct dwc3 *dwc) +{ +u32 reg; + +/* +* Prevent host/device reset from resetting OTG core. +* If we don't do this then xhci_reset (USBCMD.HCRST) will reset +* the signal outputs sent to the PHY, the OTG FSM logic of the +* core and also the resets to the VBUS filters inside the core. +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg |=DWC3_OCFG_SFTRSTMASK ; +dwc3_writel (dwc->regs,DWC3_OCFG , reg);
Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1011
Quoted 5 lines
drivers/usb/dwc3/core.c +5
-0+ +/* Disable hibernation for simplicity */ + reg =dwc3_readl (dwc->regs,DWC3_GCTL ); + reg &= ~DWC3_GCTL_GBLHIBERNATIONEN ; +dwc3_writel (dwc->regs,DWC3_GCTL , reg);no, don't do that. We support hibernation on some Intel devices. You'd be regressing them, most likely.
Do they support dual-role as well? Either ways I can omit this step.
Quoted 12 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1019
Quoted 8 lines
drivers/usb/dwc3/core.c +7
-0+/* +* Initialize OTG registers as per +* Figure 11-4 OTG Driver Overall Programming Flow +*/ +/* OCFG.SRPCap = 0, OCFG.HNPCap = 0 */ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~(DWC3_OCFG_SRPCAP |DWC3_OCFG_HNPCAP );are you sure *NO* DWC3 implementation out there is SRP capable and HNP capable?
Quoted 4 lines
HNP I understand that you want to disable because we're not support full OTG, but SRP should be easy to support and it's also rather handy. In any case, perhaps add a slightly longer comment explaining why you're disabling these?
This is done according to Fig 11.4 in the TRM. IMO it needs to be done even if the controller supports SRP and HNP.
Quoted 7 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1022
Quoted 4 lines
drivers/usb/dwc3/core.c +3
-0+dwc3_writel (dwc->regs,DWC3_OCFG , reg); +/* OEVT = FFFF */ +dwc3_writel (dwc->regs,DWC3_OEVT , ~0 );hmmm, flushing pending events. Are you sure you can even have them at this point? This should be called after we reset the controller.
This is again as per Fig 11.4 in TRM.
Quoted 7 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1026
Quoted 5 lines
drivers/usb/dwc3/core.c +4
-0+/* OEVTEN = 0 */ +dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS ); +/* OEVTEN.ConIDStsChngEn = 1. Instead we enable all events */ +dwc3_otg_enable_events (dwc,DWC3_OTG_ALL_EVENTS );oh, disable everything and enable everything right after. What gives?
I did this following Fig 11.4. But there there don't enable all events, so it was a good idea to be on a clean slate by disabling all events first and then only enabling selected events.
In any case I think it is good practice. i.e. clear before OR operation? FYI. dwc3_otg_enable_events doesn't clear the events that are not enabled so if some old event not part of enable_mask was enabled it will stay enabled.
Quoted 17 lines
Quoted 17 lines
drivers/usb/dwc3/core.c +16
-0+/* +* OCTL.PeriMode = 1, OCTL.DevSetHNPEn = 0, OCTL.HstSetHNPEn = 0, +* OCTL.HNPReq = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg |=DWC3_OCTL_PERIMODE ; + reg &= ~(DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HSTSETHNPEN | +DWC3_OCTL_HNPREQ ); +dwc3_writel (dwc->regs,DWC3_OCTL , reg); +} + +/* dwc->lock must be held */ +static int dwc3_drd_start_host (struct dwc3 *dwc,int on,bool skip) +{ +u32 reg; +
Quoted 9 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1048
Quoted 6 lines
drivers/usb/dwc3/core.c +6
-0+/* switch OTG core */ +if (on) { +/* As per Figure 11-10 A-Device Flow Diagram */ +/* OCFG.HNPCap = 0, OCFG.SRPCap = 0 */ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~(DWC3_OCFG_SRPCAP |DWC3_OCFG_HNPCAP );didn't you do this already? Why do you need to do this again?
Was blindly following Fig 11-10. Might be necessary whenever we support HNP/SRP. I can get rid of it though if you prefer.
Quoted 12 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1057
Quoted 9 lines
drivers/usb/dwc3/core.c +9
-0+dwc3_writel (dwc->regs,DWC3_OCFG , reg); + +/* +* OCTL.PeriMode=0, OCTL.TermSelDLPulse = 0, +* OCTL.DevSetHNPEn = 0, OCTL.HstSetHNPEn = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg &= ~(DWC3_OCTL_PERIMODE |DWC3_OCTL_TERMSELIDPULSE | +DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HSTSETHNPEN );HNP already disabled elsewhere. Why disable it again?
Strictly following TRM. nothing else. What do you want me to do here?
Quoted 10 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1064
Quoted 7 lines
drivers/usb/dwc3/core.c +7
-0+dwc3_writel (dwc->regs,DWC3_OCTL , reg); + +/* +* OCFG.DisPrtPwrCutoff = 0/1 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~DWC3_OCFG_DISPWRCUTTOFF ;^^ one T enough?
Quoted 3 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1060
Quoted 1 line
drivers/usb/dwc3/core.c +1
-0+dwc3_writel (dwc->regs,DWC3_OCFG , reg);should you really always disable port power cutoff ?
If I remember right this should be disabled for non OTG cases else core will turn off VBUS after A_WAIT_BCON timeout when port is disconnected.
Quoted 6 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1062
Quoted 3 lines
drivers/usb/dwc3/core.c +2
-0+/* start the xHCI host driver */ +if (!skip) {when would skip be true?
only during system resume.
Quoted 16 lines
Quoted 16 lines
drivers/usb/dwc3/core.c +16
-0+spin_unlock (&dwc->lock); +dwc3_host_init (dwc); +spin_lock (&dwc->lock); + } + +/* +* OCFG.SRPCap = 1, OCFG.HNPCap = GHWPARAMS6.HNP_CAP +* We don't want SRP/HNP for simple dual-role so leave +* these disabled. +*/ + +/* +* OEVTEN.OTGADevHostEvntEn = 1 +* OEVTEN.OTGADevSessEndDetEvntEn = 1 +* We don't want HNP/role-swap so leave these disabled. +*/
Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1090
Quoted 6 lines
drivers/usb/dwc3/core.c +6
-0+ +/* GUSB2PHYCFG.ULPIAutoRes = 1/0, GUSB2PHYCFG.SusPHY = 1 */ +if (!dwc->dis_u2_susphy_quirk) { + reg =dwc3_readl (dwc->regs,DWC3_GUSB2PHYCFG (0 )); + reg |=DWC3_GUSB2PHYCFG_SUSPHY ; +dwc3_writel (dwc->regs,DWC3_GUSB2PHYCFG (0 ), reg);already done elsewhere. Why do you need to do it again?
Indeed. I'll get rid if this.
Quoted 13 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1096
Quoted 7 lines
drivers/usb/dwc3/core.c +6
-0+ } + +/* Set Port Power to enable VBUS: OCTL.PrtPwrCtl = 1 */ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg |=DWC3_OCTL_PRTPWRCTL ; +dwc3_writel (dwc->regs,DWC3_OCTL , reg);I wonder if you have a race here with xHCI. You're essentially enable port power after xHCI has been loaded already. Mathias, do you see any problems with this? Could we confuse xHCI with this? I'm assuming there are no issues since without VBUS xHCI wouldn't see any port status change events, but thought I'd ask anyway.
We haven't seen any problems with XHCI with our testing yet.
Quoted 12 lines
Quoted 12 lines
drivers/usb/dwc3/core.c +11
-0+ }else { +/* +* Exit from A-device flow as per +* Figure 11-4 OTG Driver Overall Programming Flow +*/ +/* stop the HCD */ +if (!skip) { +spin_unlock (&dwc->lock); +dwc3_host_exit (dwc); +spin_lock (&dwc->lock); + }
Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1113
Quoted 6 lines
drivers/usb/dwc3/core.c +6
-0+ +/* +* OEVTEN.OTGADevBHostEndEvntEn=0, OEVTEN.OTGADevHNPChngEvntEn=0 +* OEVTEN.OTGADevSessEndDetEvntEn=0, +* OEVTEN.OTGADevHostEvntEn = 0 +* But we don't disable any OTG events why not?
because we kept all of them enabled based on your suggestion last year (unlike what TRM says)
Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1118
Quoted 6 lines
drivers/usb/dwc3/core.c +5
-0+*/ + +/* OCTL.HstSetHNPEn = 0, OCTL.PrtPwrCtl=0 */ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg &= ~(DWC3_OCTL_HSTSETHNPEN |DWC3_OCTL_PRTPWRCTL );disabled elsewhere. Why do it again?
I can optimize it away if you prefer.
Quoted 9 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1122
Quoted 5 lines
drivers/usb/dwc3/core.c +4
-0+dwc3_writel (dwc->regs,DWC3_OCTL , reg); + +/* Initialize OTG registers */ +dwc3_otgregs_init (dwc);again you reinitialize everything. Why so many reinitializations? Seems like you were having issues getting this to work and ended up with silly reinitializations and workqueues in an effort to get it working.
Felipe, last year you told me to strictly follow the TRM programming model. This is what it says to do. Please refer Fig 11.4
I know some things are silly but I deliberately didn't optimize them. If you want to now not strictly follow the TRM I'm fine with that as well.
Quoted 3 lines
This patch gives me the impression that the feature hasn't been tested properly. :-s
It is currently undergoing testing for TI release. So far there haven't been any surprises.
Quoted 12 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1136
Quoted 10 lines
drivers/usb/dwc3/core.c +9
-0+/* dwc->lock must be held */ +static int dwc3_drd_start_gadget (struct dwc3 *dwc,int on) +{ +u32 reg; + +if (on) +dwc3_event_buffers_setup (dwc); + +if (on) {if (on)
Quoted 6 lines
[..]if (on)
[..]:-s
:P
Quoted 43 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1144
Quoted 7 lines
drivers/usb/dwc3/core.c +6
-0+/* +* OCFG.HNPCap = GHWPARAMS6.HNP_CAP, OCFG.SRPCap = 1 +* but we set them to 0 for simple dual-role operation. +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~(DWC3_OCFG_SRPCAP |DWC3_OCFG_HNPCAP );and again clearing bits that have already been cleared multiple times.
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1146
Quoted 2 lines
drivers/usb/dwc3/core.c +2
-0+/* OCFG.OTGSftRstMsk = 0/1 */ + reg |=DWC3_OCFG_SFTRSTMASK ;do you need to set this again?
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1156
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+dwc3_writel (dwc->regs,DWC3_OCFG , reg); +/* +* OCTL.PeriMode = 1 +* OCTL.TermSelDLPulse = 0/1, OCTL.HNPReq = 0 +* OCTL.DevSetHNPEn = 0, OCTL.HstSetHNPEn = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg |=DWC3_OCTL_PERIMODE ; + reg &= ~(DWC3_OCTL_TERMSELIDPULSE |DWC3_OCTL_HNPREQ | +DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HSTSETHNPEN );clearing bits that were already cleared.
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1168
Quoted 12 lines
drivers/usb/dwc3/core.c +12
-0+dwc3_writel (dwc->regs,DWC3_OCTL , reg); +/* OEVTEN.OTGBDevSesVldDetEvntEn = 1 */ +dwc3_otg_enable_events (dwc,DWC3_OEVT_BDEVSESSVLDDET ); +/* GUSB2PHYCFG.ULPIAutoRes = 0, GUSB2PHYCFG0.SusPHY = 1 */ +if (!dwc->dis_u2_susphy_quirk) { + reg =dwc3_readl (dwc->regs,DWC3_GUSB2PHYCFG (0 )); + reg |=DWC3_GUSB2PHYCFG_SUSPHY ; +dwc3_writel (dwc->regs,DWC3_GUSB2PHYCFG (0 ), reg); + } +/* GCTL.GblHibernationEn = 0 */ + reg =dwc3_readl (dwc->regs,DWC3_GCTL ); + reg &= ~DWC3_GCTL_GBLHIBERNATIONEN ;possibly breaking other users.
Quoted 12 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1175
Quoted 7 lines
drivers/usb/dwc3/core.c +7
-0+dwc3_writel (dwc->regs,DWC3_GCTL , reg); + +/* start the Peripheral driver */ +if (dwc->gadget_driver) { +__dwc3_gadget_start (dwc); +if (dwc->gadget_pullup) +dwc3_gadget_run_stop (dwc, true, false);why don't you add/remove the UDC just like you do for the HCD? (you wouldn't add/remove a device, but rather call usb_del_gadget_udc()/usb_add_gadget_udc() directly. Would that clean up some of this?
It causes more problems than solving anything.
e.g. An already loaded gadget driver will have to be manually removed and re-loaded to work after a peripheral to host to peripheral mode switch.
Quoted 87 lines
Quoted 6 lines
drivers/usb/dwc3/core.c +5
-0+ } + }else { +/* +* Exit from B-device flow as per +* Figure 11-4 OTG Driver Overall Programming Flow drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1190
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+*/ +/* stop the Peripheral driver */ +if (dwc->gadget_driver) { +if (dwc->gadget_pullup) +dwc3_gadget_run_stop (dwc, false, false); +spin_unlock (&dwc->lock); +if (dwc->gadget_driver->disconnect) + dwc->gadget_driver->disconnect (&dwc->gadget); +spin_lock (&dwc->lock); +__dwc3_gadget_stop (dwc);
usb_del_gadget_udc()Quoted 5 lines
drivers/usb/dwc3/core.c +5
-0+ } + +/* +* OEVTEN.OTGBDevHNPChngEvntEn = 0 +* OEVTEN.OTGBDevVBusChngEvntEn = 0 drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1205
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+* OEVTEN.OTGBDevBHostEndEvntEn = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OEVTEN ); + reg &= ~(DWC3_OEVT_BDEVHNPCHNG |DWC3_OEVT_BDEVVBUSCHNG | +DWC3_OEVT_BDEVBHOSTEND ); +dwc3_writel (dwc->regs,DWC3_OEVTEN , reg); + +/* OCTL.DevSetHNPEn = 0, OCTL.HNPReq = 0, OCTL.PeriMode=1 */ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg &= ~(DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HNPREQ );:-)
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1210
Quoted 5 lines
drivers/usb/dwc3/core.c +5
-0+ reg |=DWC3_OCTL_PERIMODE ; +dwc3_writel (dwc->regs,DWC3_OCTL , reg); + +/* Initialize OTG registers */ +dwc3_otgregs_init (dwc);:-)
Quoted 42 lines
drivers/usb/dwc3/core.c +42
-0+static int dwc3_otg_get_irq (struct dwc3 *dwc) +{ +struct platform_device *dwc3_pdev =to_platform_device (dwc->dev); +int irq; + + irq =platform_get_irq_byname (dwc3_pdev,"otg" ); +if (irq >0 ) + goto out; + +if (irq == -EPROBE_DEFER ) + goto out; + + irq =platform_get_irq_byname (dwc3_pdev,"dwc_usb3" ); +if (irq >0 ) + goto out; + +if (irq == -EPROBE_DEFER ) + goto out; + + irq =platform_get_irq (dwc3_pdev,0 ); +if (irq >0 ) + goto out; + +if (irq != -EPROBE_DEFER ) +dev_err (dwc->dev,"missing otg IRQ\n" ); + +if (!irq) + irq = -EINVAL ; + +out: +return irq; +} + +/* dwc->lock must be held */ +static void dwc3_otg_core_init (struct dwc3 *dwc) +{ +u32 reg; + +/* +* As per Figure 11-4 OTG Driver Overall Programming Flow, +* block "Initialize GCTL for OTG operation". +*/
Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1262
Quoted 5 lines
drivers/usb/dwc3/core.c +5
-0+/* GCTL.PrtCapDir=2'b11 */ +dwc3_set_mode (dwc,DWC3_GCTL_PRTCAP_OTG ); +/* GUSB2PHYCFG0.SusPHY=0 */ + reg =dwc3_readl (dwc->regs,DWC3_GUSB2PHYCFG (0 )); + reg &= ~DWC3_GUSB2PHYCFG_SUSPHY ;why here? We only need this if the quirk flag is set. If that flag has been set, this bit should have been cleared already.
Right. Will get rid of this.
Quoted 12 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1270
Quoted 9 lines
drivers/usb/dwc3/core.c +8
-0+dwc3_writel (dwc->regs,DWC3_GUSB2PHYCFG (0 ), reg); + +/* Initialize OTG registers */ +dwc3_otgregs_init (dwc); + +/* force drd state machine update the first time */ + dwc->otg_fsm.b_sess_vld =-1 ; + dwc->otg_fsm.id =-1 ;Does this work if you boot with cable already attached? Both host and peripheral cables?
Yes.
Quoted 15 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1279
Quoted 10 lines
drivers/usb/dwc3/core.c +9
-0+} + +/* dwc->lock must be held */ +static void dwc3_otg_core_exit (struct dwc3 *dwc) +{ +/* disable all otg irqs */ +dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS ); +/* clear all events */ +dwc3_writel (dwc->regs,DWC3_OEVT , ~0 );when
free_irq()is called, it will wait for the current interrupt to finish being processed, this means OEVT will already be zero but the timefree_irq()finishes running. I think you shouldn't care about this.
Quoted 1 line
Just mask all events and that should be enough.
OK.
Quoted 23 lines
Quoted 8 lines
drivers/usb/dwc3/core.c +7
-0+static int dwc3_drd_init (struct dwc3 *dwc) +{ +int ret, irq; +unsigned long flags; + +INIT_WORK (&dwc->otg_work, dwc3_drd_work); +drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1298
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+ irq =dwc3_otg_get_irq (dwc); +if (irq <0 ) +return irq; + + dwc->otg_irq = irq; + +/* disable all otg irqs */ +dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS ); +/* clear all events */ +dwc3_writel (dwc->regs,DWC3_OEVT , ~0 );this is really odd. You have a bunch of these duplicated chunks of code all over the place...
Quoted 3 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1300
Quoted 1 line
drivers/usb/dwc3/core.c +1
-0+irq_set_status_flags (dwc->otg_irq,IRQ_NOAUTOEN );why?
I don't know how to fix this. I have to do this because dwc3_omap is doing it on the shared IRQ line and the flags must match if we need to share it.
Quoted 15 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1311
Quoted 12 lines
drivers/usb/dwc3/core.c +11
-0+ ret =request_threaded_irq (dwc->otg_irq, dwc3_otg_irq, + dwc3_otg_thread_irq, +IRQF_SHARED ,"dwc3-otg" , dwc); +if (ret) { +dev_err (dwc->dev,"failed to request irq #%d --> %d\n" , + dwc->otg_irq, ret); + ret = -ENODEV ; +return ret; + } + + ret =dwc3_gadget_init (dwc);unconditionally? What if I booted with a micro-A plugged to my port and a USB-stick attached to it?
We are not starting the gadget controller though and we want UDC to be initialized anyways so users can load a gadget driver before hand.
This is another point against using usb_del_gadget_udc(). The gadget controller is really there and user wants to have a persistant gadget driver loaded between host/peripheral mode switches.
Quoted 15 lines
I think this should be conditional on extcon cable state.
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1320
Quoted 9 lines
drivers/usb/dwc3/core.c +9
-0+if (ret) { +free_irq (dwc->otg_irq, dwc); +return ret; + } + +spin_lock_irqsave (&dwc->lock, flags); +dwc3_otg_core_init (dwc); +spin_unlock_irqrestore (&dwc->lock, flags); +queue_work (system_power_efficient_wq, &dwc->otg_work);:-s
Quoted 16 lines
Quoted 4 lines
drivers/usb/dwc3/core.c +4
-0+return 0 ; +} + +static void dwc3_drd_exit (struct dwc3 *dwc)drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1335
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+{ +unsigned long flags; + +cancel_work_sync (&dwc->otg_work); +spin_lock_irqsave (&dwc->lock, flags); +dwc3_otg_core_exit (dwc); +if (dwc->otg_fsm.protocol ==PROTO_HOST ) +dwc3_drd_start_host (dwc,0 ,0 ); + dwc->otg_fsm.protocol =PROTO_UNDEF ; +free_irq (dwc->otg_irq, dwc);
free_irq()might sleep, no?
alright.
Quoted 38 lines
/**
*free_irq- free an interrupt allocated withrequest_irq
* @irq: Interrupt line to free
* @dev_id: Device identity to free
*
* Remove an interrupt handler. The handler is removed and if the
* interrupt line is no longer in use by any driver it is disabled.
* On a shared IRQ the caller must ensure the interrupt is disabled
* on the card it drives before calling this function. The function
* does not return until any executing interrupts for this IRQ
* have completed.
*
* This function must not be called from interrupt context.
*/
voidfree_irq(unsigned int irq, void *dev_id)drivers/usb/dwc3/core.c static int dwc3_suspend_common(struct dwc3 *dwc) · line 1703
Quoted 5 lines
drivers/usb/dwc3/core.c +1
-0@@ -1207,19 +1700,35 @@ static int dwc3_suspend_common(struct dwc3 *dwc) {unsigned long flags; +spin_lock_irqsave (&dwc->lock, flags);looks like it should be in a separate patch.
Quoted 13 lines
drivers/usb/dwc3/core.c +1
-1@@ -1679,7 +1684,7 @@ static void dwc3_gadget_setup_nump(struct dwc3 *dwc)dwc3_writel (dwc->regs,DWC3_DCFG , reg); } -static int __dwc3_gadget_start (struct dwc3 *dwc) +int __dwc3_gadget_start (struct dwc3 *dwc) {struct dwc3_ep *dep;int ret =0 ;@@ -1827,7 +1835,7 @@ static int dwc3_gadget_start(struct usb_gadget *g,return ret; }
Quoted 5 lines
drivers/usb/dwc3/core.c static int dwc3_gadget_start(struct usb_gadget *g, · line 1838
Quoted 2 lines
drivers/usb/dwc3/core.c +1
-1-static void __dwc3_gadget_stop (struct dwc3 *dwc) +void __dwc3_gadget_stop (struct dwc3 *dwc)shouldn't have to. Just rely on usb_add/del_gadget_udc()
Please let's not use usb_add/del_gadget_udc(). It causes more trouble for user :)
gadget_start/stop has been working beautifully with the benefit of user being able to load gadget driver at any time (even when booted with host mode) and not worrying about re-loading it between host/peripheral role swithces.
cheers,
-roger
Re: [PATCH v2 3/4] usb: dwc3: add dual-role support
Hi,
Quoted 72 lines · Roger Quadros
Quoted 63 lines
Quoted 63 lines
drivers/usb/dwc3/core.c +59
-0@@ -839,6 +841,505 @@ static int dwc3_core_get_phy(struct dwc3 *dwc)return 0 ; } +static int dwc3_drd_start_host (struct dwc3 *dwc,int on,bool skip); +static int dwc3_drd_start_gadget (struct dwc3 *dwc,int on); + +/* dwc->lock must be held */ +static void dwc3_drd_statemachine (struct dwc3 *dwc,int id,int vbus) +{ +enum usb_otg_state new_state; +int protocol; + +if (id == dwc->otg_fsm.id && vbus == dwc->otg_fsm.b_sess_vld) +return ; + + dwc->otg_fsm.id = id; + dwc->otg_fsm.b_sess_vld = vbus; + +if (!id) { + new_state =OTG_STATE_A_HOST ; + }else { +if (vbus) + new_state =OTG_STATE_B_PERIPHERAL ; +else + new_state =OTG_STATE_B_IDLE ; + } + +if (dwc->otg.state == new_state) +return ; + + protocol = dwc->otg_fsm.protocol; +switch (new_state) { +case OTG_STATE_B_IDLE : +if (protocol ==PROTO_GADGET ) +dwc3_drd_start_gadget (dwc,0 ); +else if (protocol ==PROTO_HOST ) +dwc3_drd_start_host (dwc,0 ,0 ); + dwc->otg_fsm.protocol =PROTO_UNDEF ; +break ; +case OTG_STATE_B_PERIPHERAL : +if (protocol ==PROTO_HOST ) +dwc3_drd_start_host (dwc,0 ,0 ); + +if (protocol !=PROTO_GADGET ) { + dwc->otg_fsm.protocol =PROTO_GADGET ; +dwc3_drd_start_gadget (dwc,1 ); + } +break ; +case OTG_STATE_A_HOST : +if (protocol ==PROTO_GADGET ) +dwc3_drd_start_gadget (dwc,0 ); + +if (protocol !=PROTO_HOST ) { + dwc->otg_fsm.protocol =PROTO_HOST ; +dwc3_drd_start_host (dwc,1 ,0 ); + } +break ; +default : +dev_err (dwc->dev,"drd: invalid usb-drd state: %s\n" , +usb_otg_state_string (new_state)); +return ; + }Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 905
Quoted 3 lines
drivers/usb/dwc3/core.c +3
-0+ + dwc->otg.state = new_state; +}I think I've mentioned this before. Why don't we start with the simplest possible implementation? Something that *just* allows us to get ID pin value and set the mode. After that's stable, then we add more pieces to the mix.
Quoted 5 lines
That is exactly what I'm doing. Maybe the switch case is making it look complicated.
dwc3_drd_statemachine()has only 2 inputs VBUS and ID.I can change it to if/else if you prefer that. I like the way it is cause we can define 3 states IDLE, PERIPHERAL and HOST.
Right, I like the three states, but somehow the code looks really complex :-s
Quoted 4 lines
Quoted 2 lines
For something that simple, we wouldn't even need to use OTG FSM layer because that brings no benefit for such a simple requirement.
no no. I think you got it wrong. I'm not using the OTG FSM layer at all :).
what are all the otg_fsm mentions then? Also you have:
+ struct usb_otg otg;
+ struct otg_fsm otg_fsm;
Quoted 39 lines
Quoted 39 lines
Quoted 9 lines
drivers/usb/dwc3/core.c +9
-0+/* dwc->lock must be held */ +static void dwc3_otg_fsm_sync (struct dwc3 *dwc) +{ +u32 reg; +int id, vbus; + +/* +* calling dwc3_otg_fsm_sync() during resume breaks host +* if adapter was removed during suspend as xhci driver drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 925
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+* is not prepared to see hcd removal before xhci_resume. +*/ +if (dwc->otg_prevent_sync) +return ; + + reg =dwc3_readl (dwc->regs,DWC3_OSTS ); + id = !!(reg &DWC3_OSTS_CONIDSTS ); + vbus = !!(reg &DWC3_OSTS_BSESVLD ); +dwc3_drd_statemachine (dwc, id, vbus); +}Just consider this for a moment. Consider the steps taken to get here.
- User plugs cable
- Hardirq handler run
- read register
- if (reg) returnIRQ_WAKE_THREAD;
- schedule bottom half handler to sometime in the future
- scheduler runs our threaded handler
- lock dwc3
- if (host)
- configure register
- add xHCI device
- else
-otg_fsm_sync()
-drd_statemachine()
- configure registers
- reimplement gadget initialization (same thing we do when registering UDC
Quoted 6 lines
Quoted 3 lines
I mean, just looking at this we can already see that it's really overly complex. Right now we need simple, dead simple. This will limit the possibility of errors.
OK. I can probably get rid of the state machine model and just use if/else? Anything else you want me to get rid of?
The workqueue, unless it's really, really necessary and it appears like it shouldn't be.
We _can_ keep the switch statement. The problem is not the switch statement, it's the reimplementation of code we already have.
All you do with adding and removing UDC/HCD is already available somewhere. Perhaps it just needs to be extracted to a function you can call, but the code is already there, since we need it for loading/unloading dwc3 itself.
Quoted 16 lines
Quoted 16 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 935
Quoted 9 lines
drivers/usb/dwc3/core.c +9
-0+static void dwc3_drd_work (struct work_struct *work) +{ + struct dwc3 *dwc = container_of(work, struct dwc3, + otg_work); + +spin_lock (&dwc->lock); +dwc3_otg_fsm_sync (dwc); +spin_unlock (&dwc->lock); +}so this is only called from ->complete(). You mentioned your commit log that calling
dwc3_otg_fsm_sync()directly from ->complete() can lock up the system. Why? I have a feeling your locking isn't proper and that's why sometimes it locks up. You introduced a deadlock and to work around it, the "solution" was to add a workqueue.
Quoted 7 lines
Quoted 1 line
Can you either confirm or refute the statement above?
The real problem was that if host adapter was removed during a system suspend then while resuming XHCI was locking up like below. This is probably because we're trying to remove/Halt the HCD in the
otg_irq_handlerbefore XHCI driver has resumed?How can we ensure that we call
dwc3_host_exit()only *after* XHCI driver has resumed?
Well, xHCI is our child, so driver model should *already* be guaranteeing that, no? Specially since you're calling this from ->complete() which happens after ->resume() has been called for the entire tree. It's true, however, that dwc3's ->complete() will be called before xhci's ->complete(). Is this the problem you're pointing at? Or do you mean xHCI is runtime suspended (or runtime resuming) while you call dwc3_host_exit()? If that's the case, then there's a bug in xHCI itself.
We should be able to remove a device from platform/pci bus at any time.
Quoted 39 lines
[ 1057.565573] PM: Syncing filesystems ... done. [ 1057.573986] PM: Preparing system for sleep (mem) [ 1057.580282] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 1057.589626] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 1057.598931] PM: Suspending system (mem) [ 1057.617852] PM: suspend of devices complete after 13.163 msecs [ 1057.628279] PM: late suspend of devices complete after 4.296 msecs [ 1057.635858] PM: noirq resume of devices complete after 0.178 msecs [ 1057.642783] PM: noirq suspend of devices failed [ 1057.649703] PM: early resume of devices complete after 2.134 msecs [ 1057.658046] net eth0: initializing cpsw version 1.15 (0) [ 1057.663634] cpsw 48484000.ethernet: initialized cpsw ale version 1.4 [ 1057.670325] cpsw 48484000.ethernet: ALE Table size 1024 [ 1057.683322] Generic PHY 48485000.mdio:02: attached PHY driver [Generic PHY] (mii_bus:phy_addr=48485000.mdio:02, irq=-1) [ 1057.706453] usb usb1: root hub lost power or was reset [ 1057.711847] usb usb2: root hub lost power or was reset [ 1057.987078] ata1: SATA link down (SStatus 0 SControl 300) [ 1059.762288] cpsw 48484000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx[ 1061.846695] PM: resume of devices complete after 4190.473 msecs [ 1061.853294] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 1061.858644] usb usb2: USB disconnect, device number 1 [ 1061.890701] xhci-hcd xhci-hcd.0.auto: Host halt failed, -110 [ 1061.896640] xhci-hcd xhci-hcd.0.auto: Host controller not halted, aborting reset. [ 1061.904535] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered [ 1061.910514] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 1061.915848] usb usb1: USB disconnect, device number 1 [ 1061.921146] usb 1-1: USB disconnect, device number 2Quoted 9 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 941
Quoted 6 lines
drivers/usb/dwc3/core.c +5
-0+static void dwc3_otg_disable_events (struct dwc3 *dwc,u32 disable_mask) +{ + dwc->oevten &= ~(disable_mask); +dwc3_writel (dwc->regs,DWC3_OEVTEN , dwc->oevten); +}we should disable OTG events from our top half handler, otherwise top and bottom half can race with each other.
Quoted 2 lines
If we disable OTG events then there is a chance that we miss the events that happen while they were disabled.
no, they'll be in the register. Once we reenable them, then the IRQ line will be raised once more and our handler will get scheduled.
Quoted 2 lines
We need a way to mask the OTG events without loosing them while they are masked. Do you know how that could be achieved?
masking doesn't clear events. It just masks them. Look at gadget.c for how we do it. Basically, the code we have here is racy, really racy and will cause hard-to-debug lockups. Your code can only work with IRQF_ONESHOT, which we don't want to add back.
In any case, to mask events, you set BIT 31 in GEVNTSIZ register. Just copy it from gadget.c ;-)
Quoted 21 lines
Quoted 12 lines
Quoted 12 lines
drivers/usb/dwc3/core.c +12
-0+spin_unlock (&dwc->lock); + +return IRQ_HANDLED ; +} + +static irqreturn_t dwc3_otg_irq (int irq,void *_dwc) +{ +u32 reg; +struct dwc3 *dwc = _dwc; +irqreturn_t ret =IRQ_NONE ; + + reg =dwc3_readl (dwc->regs,DWC3_OEVT );Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 987
Quoted 6 lines
drivers/usb/dwc3/core.c +6
-0+if (reg) { +if ((dwc->otg_fsm.protocol ==PROTO_HOST ) && + !(reg &DWC3_OEVT_DEVICEMODE )) + dwc->otg_needs_host_start =1 ; +dwc3_writel (dwc->regs,DWC3_OEVT , reg); + ret =IRQ_WAKE_THREAD ;
disable_events();
Quoted 1 line
We can't disable events if we don't want to miss any events while they were disabled.
right, disable events is not the best thing, sorry. We should set bit 31 in GEVNTSIZ.
Quoted 2 lines
But I agree that we need to prevent them from firing another hard IRQ. I couldn't figure out how that can be done.
gadget.c ;-)
Quoted 27 lines
Quoted 18 lines
Quoted 18 lines
drivers/usb/dwc3/core.c +18
-0+ +return ret; +} + +/* --------------------- Dual-Role management ------------------------------- */ +static void dwc3_otgregs_init (struct dwc3 *dwc) +{ +u32 reg; + +/* +* Prevent host/device reset from resetting OTG core. +* If we don't do this then xhci_reset (USBCMD.HCRST) will reset +* the signal outputs sent to the PHY, the OTG FSM logic of the +* core and also the resets to the VBUS filters inside the core. +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg |=DWC3_OCFG_SFTRSTMASK ; +dwc3_writel (dwc->regs,DWC3_OCFG , reg);Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1011
Quoted 5 lines
drivers/usb/dwc3/core.c +5
-0+ +/* Disable hibernation for simplicity */ + reg =dwc3_readl (dwc->regs,DWC3_GCTL ); + reg &= ~DWC3_GCTL_GBLHIBERNATIONEN ; +dwc3_writel (dwc->regs,DWC3_GCTL , reg);no, don't do that. We support hibernation on some Intel devices. You'd be regressing them, most likely.
Quoted 1 line
Do they support dual-role as well? Either ways I can omit this step.
At least for now, let's skip it.
Quoted 11 lines
Quoted 11 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1019
Quoted 7 lines
drivers/usb/dwc3/core.c +7
-0+/* +* Initialize OTG registers as per +* Figure 11-4 OTG Driver Overall Programming Flow +*/ +/* OCFG.SRPCap = 0, OCFG.HNPCap = 0 */ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~(DWC3_OCFG_SRPCAP |DWC3_OCFG_HNPCAP );are you sure *NO* DWC3 implementation out there is SRP capable and HNP capable?
Quoted 7 lines
Quoted 4 lines
HNP I understand that you want to disable because we're not support full OTG, but SRP should be easy to support and it's also rather handy. In any case, perhaps add a slightly longer comment explaining why you're disabling these?
This is done according to Fig 11.4 in the TRM. IMO it needs to be done even if the controller supports SRP and HNP.
I see, fair enough.
Quoted 8 lines
Quoted 6 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1022
Quoted 3 lines
drivers/usb/dwc3/core.c +3
-0+dwc3_writel (dwc->regs,DWC3_OCFG , reg); +/* OEVT = FFFF */ +dwc3_writel (dwc->regs,DWC3_OEVT , ~0 );hmmm, flushing pending events. Are you sure you can even have them at this point? This should be called after we reset the controller.
This is again as per Fig 11.4 in TRM.
documentation might have made assumptions which don't apply to us :-)
Quoted 7 lines
Quoted 6 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1026
Quoted 4 lines
drivers/usb/dwc3/core.c +4
-0+/* OEVTEN = 0 */ +dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS ); +/* OEVTEN.ConIDStsChngEn = 1. Instead we enable all events */ +dwc3_otg_enable_events (dwc,DWC3_OTG_ALL_EVENTS );oh, disable everything and enable everything right after. What gives?
Quoted 7 lines
I did this following Fig 11.4. But there there don't enable all events, so it was a good idea to be on a clean slate by disabling all events first and then only enabling selected events.
In any case I think it is good practice. i.e. clear before OR operation? FYI.
dwc3_otg_enable_eventsdoesn't clear the events that are not enabled so if some old event not part ofenable_maskwas enabled it will stay enabled.
can't this result in IRQ triggering forever and us not handling it? ;-)
Quoted 26 lines
Quoted 16 lines
Quoted 16 lines
drivers/usb/dwc3/core.c +16
-0+/* +* OCTL.PeriMode = 1, OCTL.DevSetHNPEn = 0, OCTL.HstSetHNPEn = 0, +* OCTL.HNPReq = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg |=DWC3_OCTL_PERIMODE ; + reg &= ~(DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HSTSETHNPEN | +DWC3_OCTL_HNPREQ ); +dwc3_writel (dwc->regs,DWC3_OCTL , reg); +} + +/* dwc->lock must be held */ +static int dwc3_drd_start_host (struct dwc3 *dwc,int on,bool skip) +{ +u32 reg; +Quoted 9 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1048
Quoted 6 lines
drivers/usb/dwc3/core.c +6
-0+/* switch OTG core */ +if (on) { +/* As per Figure 11-10 A-Device Flow Diagram */ +/* OCFG.HNPCap = 0, OCFG.SRPCap = 0 */ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~(DWC3_OCFG_SRPCAP |DWC3_OCFG_HNPCAP );didn't you do this already? Why do you need to do this again?
Quoted 2 lines
Was blindly following Fig 11-10. Might be necessary whenever we support HNP/SRP. I can get rid of it though if you prefer.
please do, minimal support for now ;-)
Quoted 13 lines
Quoted 12 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1057
Quoted 9 lines
drivers/usb/dwc3/core.c +9
-0+dwc3_writel (dwc->regs,DWC3_OCFG , reg); + +/* +* OCTL.PeriMode=0, OCTL.TermSelDLPulse = 0, +* OCTL.DevSetHNPEn = 0, OCTL.HstSetHNPEn = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg &= ~(DWC3_OCTL_PERIMODE |DWC3_OCTL_TERMSELIDPULSE | +DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HSTSETHNPEN );HNP already disabled elsewhere. Why disable it again?
Quoted 1 line
Strictly following TRM. nothing else. What do you want me to do here?
assume your register writes actually stick :-)
Quoted 10 lines
Quoted 10 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1064
Quoted 7 lines
drivers/usb/dwc3/core.c +7
-0+dwc3_writel (dwc->regs,DWC3_OCTL , reg); + +/* +* OCFG.DisPrtPwrCutoff = 0/1 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~DWC3_OCFG_DISPWRCUTTOFF ;^^ one T enough?
Quoted 7 lines
Quoted 3 lines
Review static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1032
Quoted 1 line
(quoted diff) +1
-0+ dwc3_writel(dwc->regs, DWC3_OCFG, reg);should you really always disable port power cutoff ?
If I remember right this should be disabled for non OTG cases else core will turn off VBUS after
A_WAIT_BCONtimeout when port is disconnected.
aha, good point :-)
Quoted 7 lines
Quoted 5 lines
Review static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1034
Quoted 2 lines
(quoted diff) +2
-0+ /* start the xHCI host driver */ + if (!skip) {when would skip be true?
only during system resume.
hmmm, is there a reason for that? I mean, could we live without it for the time being? Seems like all this achieves is avoiding reenumeration of some devices during resume. Do we care from a starting implementation?
Quoted 20 lines
Quoted 11 lines
Quoted 11 lines
drivers/usb/dwc3/core.c +11
-0+ }else { +/* +* Exit from A-device flow as per +* Figure 11-4 OTG Driver Overall Programming Flow +*/ +/* stop the HCD */ +if (!skip) { +spin_unlock (&dwc->lock); +dwc3_host_exit (dwc); +spin_lock (&dwc->lock); + }Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1113
Quoted 6 lines
drivers/usb/dwc3/core.c +6
-0+ +/* +* OEVTEN.OTGADevBHostEndEvntEn=0, OEVTEN.OTGADevHNPChngEvntEn=0 +* OEVTEN.OTGADevSessEndDetEvntEn=0, +* OEVTEN.OTGADevHostEvntEn = 0 +* But we don't disable any OTG events why not?
Quoted 2 lines
because we kept all of them enabled based on your suggestion last year (unlike what TRM says)
Hmm, I see. I, clearly, forgot what I said. :-p Sorry
Quoted 9 lines
Quoted 7 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1118
Quoted 5 lines
drivers/usb/dwc3/core.c +5
-0+*/ + +/* OCTL.HstSetHNPEn = 0, OCTL.PrtPwrCtl=0 */ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg &= ~(DWC3_OCTL_HSTSETHNPEN |DWC3_OCTL_PRTPWRCTL );disabled elsewhere. Why do it again?
I can optimize it away if you prefer.
we gotta start with an assumption that the HW works. If it doesn't, we quirk it out.
Quoted 9 lines
Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1122
Quoted 4 lines
drivers/usb/dwc3/core.c +4
-0+dwc3_writel (dwc->regs,DWC3_OCTL , reg); + +/* Initialize OTG registers */ +dwc3_otgregs_init (dwc);again you reinitialize everything. Why so many reinitializations? Seems like you were having issues getting this to work and ended up with silly reinitializations and workqueues in an effort to get it working.
Quoted 5 lines
Felipe, last year you told me to strictly follow the TRM programming model. This is what it says to do. Please refer Fig 11.4
I know some things are silly but I deliberately didn't optimize them. If you want to now not strictly follow the TRM I'm fine with that as well.
I see what you're doing now.
Quoted 5 lines
Quoted 2 lines
This patch gives me the impression that the feature hasn't been tested properly. :-s
It is currently undergoing testing for TI release. So far there haven't been any surprises.
good to know
Quoted 13 lines
Quoted 4 lines
Quoted 4 lines
drivers/usb/dwc3/core.c +4
-0+dwc3_writel (dwc->regs,DWC3_GCTL , reg); + +/* start the Peripheral driver */ +if (dwc->gadget_driver) {Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1175
Quoted 3 lines
drivers/usb/dwc3/core.c +3
-0+__dwc3_gadget_start (dwc); +if (dwc->gadget_pullup) +dwc3_gadget_run_stop (dwc, true, false);why don't you add/remove the UDC just like you do for the HCD? (you wouldn't add/remove a device, but rather call usb_del_gadget_udc()/usb_add_gadget_udc() directly. Would that clean up some of this?
Quoted 3 lines
It causes more problems than solving anything.
e.g. An already loaded gadget driver will have to be manually removed and re-loaded to work after a peripheral to host to peripheral mode switch.
is that really still true? When we remove the UDC, the currently-loaded gadget driver will be moved to the pending list. Once a UDC is added back, udc-core will bind it again to the UDC.
Quoted 12 lines
Quoted 11 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1270
Quoted 8 lines
drivers/usb/dwc3/core.c +8
-0+dwc3_writel (dwc->regs,DWC3_GUSB2PHYCFG (0 ), reg); + +/* Initialize OTG registers */ +dwc3_otgregs_init (dwc); + +/* force drd state machine update the first time */ + dwc->otg_fsm.b_sess_vld =-1 ; + dwc->otg_fsm.id =-1 ;Does this work if you boot with cable already attached? Both host and peripheral cables?
Quoted 1 line
Yes.
fair enough
Quoted 22 lines
Quoted 22 lines
Quoted 7 lines
drivers/usb/dwc3/core.c +7
-0+static int dwc3_drd_init (struct dwc3 *dwc) +{ +int ret, irq; +unsigned long flags; + +INIT_WORK (&dwc->otg_work, dwc3_drd_work); +drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1298
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+ irq =dwc3_otg_get_irq (dwc); +if (irq <0 ) +return irq; + + dwc->otg_irq = irq; + +/* disable all otg irqs */ +dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS ); +/* clear all events */ +dwc3_writel (dwc->regs,DWC3_OEVT , ~0 );this is really odd. You have a bunch of these duplicated chunks of code all over the place...
Quoted 6 lines
Quoted 3 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1300
Quoted 1 line
drivers/usb/dwc3/core.c +1
-0+irq_set_status_flags (dwc->otg_irq,IRQ_NOAUTOEN );why?
I don't know how to fix this. I have to do this because
dwc3_omapis doing it on the shared IRQ line and the flags must match if we need to share it.
hmmm... Then why does dwc_omap IRQ have IRQ_NOAUTOEN and otg_irq doesn't?
Quoted 15 lines
Quoted 6 lines
Quoted 6 lines
drivers/usb/dwc3/core.c +6
-0+ ret =request_threaded_irq (dwc->otg_irq, dwc3_otg_irq, + dwc3_otg_thread_irq, +IRQF_SHARED ,"dwc3-otg" , dwc); +if (ret) { +dev_err (dwc->dev,"failed to request irq #%d --> %d\n" , + dwc->otg_irq, ret);Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1311
Quoted 5 lines
drivers/usb/dwc3/core.c +5
-0+ ret = -ENODEV ; +return ret; + } + + ret =dwc3_gadget_init (dwc);unconditionally? What if I booted with a micro-A plugged to my port and a USB-stick attached to it?
Quoted 2 lines
We are not starting the gadget controller though and we want UDC to be initialized anyways so users can load a gadget driver before hand.
Users will be able to load gadget driver and that will be kept in the pending list until a UDC is loaded.
Quoted 3 lines
This is another point against using
usb_del_gadget_udc(). The gadget controller is really there and user wants to have a persistant gadget driver loaded between host/peripheral mode switches.
see above.
Quoted 11 lines
Quoted 9 lines
drivers/usb/dwc3/gadget.c static int dwc3_gadget_start(struct usb_gadget *g, · line 1838
Quoted 6 lines
drivers/usb/dwc3/gadget.c +1
-1@@ -1827,7 +1835,7 @@ static int dwc3_gadget_start(struct usb_gadget *g,return ret; } -static void __dwc3_gadget_stop (struct dwc3 *dwc) +void __dwc3_gadget_stop (struct dwc3 *dwc)shouldn't have to. Just rely on usb_add/del_gadget_udc()
Please let's not use usb_add/del_gadget_udc(). It causes more trouble for user :)
I can't see why it would :-s
Quoted 4 lines
gadget_start/stop has been working beautifully with the benefit of user being able to load gadget driver at any time (even when booted with host mode) and not worrying about re-loading it between host/peripheral role swithces.
If that's still necessary, we have a bug in udc-core. That needs to be fixed :-)
Signature · 1 line
balbi
Re: [PATCH v2 3/4] usb: dwc3: add dual-role support
Hi,
Quoted 88 lines · Felipe Balbi
Hi,
Quoted 72 lines · Roger Quadros
Quoted 63 lines
Quoted 63 lines
drivers/usb/dwc3/core.c +59
-0@@ -839,6 +841,505 @@ static int dwc3_core_get_phy(struct dwc3 *dwc)return 0 ; } +static int dwc3_drd_start_host (struct dwc3 *dwc,int on,bool skip); +static int dwc3_drd_start_gadget (struct dwc3 *dwc,int on); + +/* dwc->lock must be held */ +static void dwc3_drd_statemachine (struct dwc3 *dwc,int id,int vbus) +{ +enum usb_otg_state new_state; +int protocol; + +if (id == dwc->otg_fsm.id && vbus == dwc->otg_fsm.b_sess_vld) +return ; + + dwc->otg_fsm.id = id; + dwc->otg_fsm.b_sess_vld = vbus; + +if (!id) { + new_state =OTG_STATE_A_HOST ; + }else { +if (vbus) + new_state =OTG_STATE_B_PERIPHERAL ; +else + new_state =OTG_STATE_B_IDLE ; + } + +if (dwc->otg.state == new_state) +return ; + + protocol = dwc->otg_fsm.protocol; +switch (new_state) { +case OTG_STATE_B_IDLE : +if (protocol ==PROTO_GADGET ) +dwc3_drd_start_gadget (dwc,0 ); +else if (protocol ==PROTO_HOST ) +dwc3_drd_start_host (dwc,0 ,0 ); + dwc->otg_fsm.protocol =PROTO_UNDEF ; +break ; +case OTG_STATE_B_PERIPHERAL : +if (protocol ==PROTO_HOST ) +dwc3_drd_start_host (dwc,0 ,0 ); + +if (protocol !=PROTO_GADGET ) { + dwc->otg_fsm.protocol =PROTO_GADGET ; +dwc3_drd_start_gadget (dwc,1 ); + } +break ; +case OTG_STATE_A_HOST : +if (protocol ==PROTO_GADGET ) +dwc3_drd_start_gadget (dwc,0 ); + +if (protocol !=PROTO_HOST ) { + dwc->otg_fsm.protocol =PROTO_HOST ; +dwc3_drd_start_host (dwc,1 ,0 ); + } +break ; +default : +dev_err (dwc->dev,"drd: invalid usb-drd state: %s\n" , +usb_otg_state_string (new_state)); +return ; + }Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 905
Quoted 3 lines
drivers/usb/dwc3/core.c +3
-0+ + dwc->otg.state = new_state; +}I think I've mentioned this before. Why don't we start with the simplest possible implementation? Something that *just* allows us to get ID pin value and set the mode. After that's stable, then we add more pieces to the mix.
Quoted 5 lines
That is exactly what I'm doing. Maybe the switch case is making it look complicated.
dwc3_drd_statemachine()has only 2 inputs VBUS and ID.I can change it to if/else if you prefer that. I like the way it is cause we can define 3 states IDLE, PERIPHERAL and HOST.
Right, I like the three states, but somehow the code looks really complex :-s
Quoted 3 lines
Quoted 2 lines
For something that simple, we wouldn't even need to use OTG FSM layer because that brings no benefit for such a simple requirement.
Quoted 7 lines
Quoted 1 line
no no. I think you got it wrong. I'm not using the OTG FSM layer at all :).
what are all the
otg_fsmmentions then? Also you have:+ struct
usb_otgotg;
+ structotg_fsmotg_fsm;
I'll get rid of them. They aren't really needed. Now I see why you thought I was using the otg_fsm layer. :)
Quoted 43 lines
Quoted 43 lines
Quoted 42 lines
Quoted 9 lines
drivers/usb/dwc3/core.c +9
-0+/* dwc->lock must be held */ +static void dwc3_otg_fsm_sync (struct dwc3 *dwc) +{ +u32 reg; +int id, vbus; + +/* +* calling dwc3_otg_fsm_sync() during resume breaks host +* if adapter was removed during suspend as xhci driver drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 925
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+* is not prepared to see hcd removal before xhci_resume. +*/ +if (dwc->otg_prevent_sync) +return ; + + reg =dwc3_readl (dwc->regs,DWC3_OSTS ); + id = !!(reg &DWC3_OSTS_CONIDSTS ); + vbus = !!(reg &DWC3_OSTS_BSESVLD ); +dwc3_drd_statemachine (dwc, id, vbus); +}Just consider this for a moment. Consider the steps taken to get here.
- User plugs cable
- Hardirq handler run
- read register
- if (reg) returnIRQ_WAKE_THREAD;
- schedule bottom half handler to sometime in the future
- scheduler runs our threaded handler
- lock dwc3
- if (host)
- configure register
- add xHCI device
- else
-otg_fsm_sync()
-drd_statemachine()
- configure registers
- reimplement gadget initialization (same thing we do when registering UDCI mean, just looking at this we can already see that it's really overly complex. Right now we need simple, dead simple. This will limit the possibility of errors.
Quoted 5 lines
Quoted 2 lines
OK. I can probably get rid of the state machine model and just use if/else? Anything else you want me to get rid of?
The workqueue, unless it's really, really necessary and it appears like it shouldn't be.
OK.
Quoted 33 lines
We _can_ keep the switch statement. The problem is not the switch statement, it's the reimplementation of code we already have.
All you do with adding and removing UDC/HCD is already available somewhere. Perhaps it just needs to be extracted to a function you can call, but the code is already there, since we need it for loading/unloading dwc3 itself.
Quoted 16 lines
Quoted 16 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 935
Quoted 9 lines
drivers/usb/dwc3/core.c +9
-0+static void dwc3_drd_work (struct work_struct *work) +{ + struct dwc3 *dwc = container_of(work, struct dwc3, + otg_work); + +spin_lock (&dwc->lock); +dwc3_otg_fsm_sync (dwc); +spin_unlock (&dwc->lock); +}so this is only called from ->complete(). You mentioned your commit log that calling
dwc3_otg_fsm_sync()directly from ->complete() can lock up the system. Why? I have a feeling your locking isn't proper and that's why sometimes it locks up. You introduced a deadlock and to work around it, the "solution" was to add a workqueue.Quoted 7 lines
Quoted 1 line
Can you either confirm or refute the statement above?
The real problem was that if host adapter was removed during a system suspend then while resuming XHCI was locking up like below. This is probably because we're trying to remove/Halt the HCD in the
otg_irq_handlerbefore XHCI driver has resumed?How can we ensure that we call
dwc3_host_exit()only *after* XHCI driver has resumed?
Quoted 8 lines
Well, xHCI is our child, so driver model should *already* be guaranteeing that, no? Specially since you're calling this from ->complete() which happens after ->resume() has been called for the entire tree. It's true, however, that dwc3's ->complete() will be called before xhci's ->complete(). Is this the problem you're pointing at? Or do you mean xHCI is runtime suspended (or runtime resuming) while you call
dwc3_host_exit()? If that's the case, then there's a bug in xHCI itself.
Yes dwc3->complete() being called before xhci->complete(), and so HCD being removed before xhci->complete() causes the lockup.
It could be a bug in xHCI driver as well.
Quoted 42 lines
We should be able to remove a device from platform/pci bus at any time.
Quoted 39 lines
[ 1057.565573] PM: Syncing filesystems ... done. [ 1057.573986] PM: Preparing system for sleep (mem) [ 1057.580282] Freezing user space processes ... (elapsed 0.001 seconds) done. [ 1057.589626] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 1057.598931] PM: Suspending system (mem) [ 1057.617852] PM: suspend of devices complete after 13.163 msecs [ 1057.628279] PM: late suspend of devices complete after 4.296 msecs [ 1057.635858] PM: noirq resume of devices complete after 0.178 msecs [ 1057.642783] PM: noirq suspend of devices failed [ 1057.649703] PM: early resume of devices complete after 2.134 msecs [ 1057.658046] net eth0: initializing cpsw version 1.15 (0) [ 1057.663634] cpsw 48484000.ethernet: initialized cpsw ale version 1.4 [ 1057.670325] cpsw 48484000.ethernet: ALE Table size 1024 [ 1057.683322] Generic PHY 48485000.mdio:02: attached PHY driver [Generic PHY] (mii_bus:phy_addr=48485000.mdio:02, irq=-1) [ 1057.706453] usb usb1: root hub lost power or was reset [ 1057.711847] usb usb2: root hub lost power or was reset [ 1057.987078] ata1: SATA link down (SStatus 0 SControl 300) [ 1059.762288] cpsw 48484000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx[ 1061.846695] PM: resume of devices complete after 4190.473 msecs [ 1061.853294] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 1061.858644] usb usb2: USB disconnect, device number 1 [ 1061.890701] xhci-hcd xhci-hcd.0.auto: Host halt failed, -110 [ 1061.896640] xhci-hcd xhci-hcd.0.auto: Host controller not halted, aborting reset. [ 1061.904535] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered [ 1061.910514] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 1061.915848] usb usb1: USB disconnect, device number 1 [ 1061.921146] usb 1-1: USB disconnect, device number 2Quoted 9 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 941
Quoted 6 lines
drivers/usb/dwc3/core.c +5
-0+static void dwc3_otg_disable_events (struct dwc3 *dwc,u32 disable_mask) +{ + dwc->oevten &= ~(disable_mask); +dwc3_writel (dwc->regs,DWC3_OEVTEN , dwc->oevten); +}we should disable OTG events from our top half handler, otherwise top and bottom half can race with each other.
Quoted 5 lines
Quoted 2 lines
If we disable OTG events then there is a chance that we miss the events that happen while they were disabled.
no, they'll be in the register. Once we reenable them, then the IRQ line will be raised once more and our handler will get scheduled.
At least when I tested it by disabling events in OEVTEN, the events were missed. There should be another way to mask the interrupts than OEVTEN.
Quoted 11 lines
Quoted 3 lines
We need a way to mask the OTG events without loosing them while they are masked. Do you know how that could be achieved?
masking doesn't clear events. It just masks them. Look at
gadget.cfor how we do it. Basically, the code we have here is racy, really racy and will cause hard-to-debug lockups. Your code can only work withIRQF_ONESHOT, which we don't want to add back.In any case, to mask events, you set BIT 31 in GEVNTSIZ register. Just copy it from
gadget.c;-)
Isn't GEVNTSIZ specific to device side? We're talking about the OTG block here. Are you sure that setting bit 31 of GEVNTSIZ will mask OTG_irq? I don't think so.
Note that OTG_IRQ is a separate IRQ line than PERIPHERAL_IRQ.
Quoted 59 lines
Quoted 22 lines
Quoted 13 lines
Quoted 13 lines
drivers/usb/dwc3/core.c +12
-0+spin_unlock (&dwc->lock); + +return IRQ_HANDLED ; +} + +static irqreturn_t dwc3_otg_irq (int irq,void *_dwc) +{ +u32 reg; +struct dwc3 *dwc = _dwc; +irqreturn_t ret =IRQ_NONE ; + + reg =dwc3_readl (dwc->regs,DWC3_OEVT );Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 987
Quoted 6 lines
drivers/usb/dwc3/core.c +6
-0+if (reg) { +if ((dwc->otg_fsm.protocol ==PROTO_HOST ) && + !(reg &DWC3_OEVT_DEVICEMODE )) + dwc->otg_needs_host_start =1 ; +dwc3_writel (dwc->regs,DWC3_OEVT , reg); + ret =IRQ_WAKE_THREAD ;
disable_events();Quoted 1 line
We can't disable events if we don't want to miss any events while they were disabled.
right, disable events is not the best thing, sorry. We should set bit 31 in GEVNTSIZ.
Quoted 2 lines
But I agree that we need to prevent them from firing another hard IRQ. I couldn't figure out how that can be done.
gadget.c;-)Quoted 27 lines
Quoted 26 lines
Quoted 13 lines
drivers/usb/dwc3/core.c +13
-0+ +return ret; +} + +/* --------------------- Dual-Role management ------------------------------- */ +static void dwc3_otgregs_init (struct dwc3 *dwc) +{ +u32 reg; + +/* +* Prevent host/device reset from resetting OTG core. +* If we don't do this then xhci_reset (USBCMD.HCRST) will reset +* the signal outputs sent to the PHY, the OTG FSM logic of the drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1011
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+* core and also the resets to the VBUS filters inside the core. +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg |=DWC3_OCFG_SFTRSTMASK ; +dwc3_writel (dwc->regs,DWC3_OCFG , reg); + +/* Disable hibernation for simplicity */ + reg =dwc3_readl (dwc->regs,DWC3_GCTL ); + reg &= ~DWC3_GCTL_GBLHIBERNATIONEN ; +dwc3_writel (dwc->regs,DWC3_GCTL , reg);no, don't do that. We support hibernation on some Intel devices. You'd be regressing them, most likely.
Quoted 3 lines
Quoted 1 line
Do they support dual-role as well? Either ways I can omit this step.
At least for now, let's skip it.
OK.
Quoted 44 lines
Quoted 12 lines
Quoted 12 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1019
Quoted 8 lines
drivers/usb/dwc3/core.c +7
-0+/* +* Initialize OTG registers as per +* Figure 11-4 OTG Driver Overall Programming Flow +*/ +/* OCFG.SRPCap = 0, OCFG.HNPCap = 0 */ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~(DWC3_OCFG_SRPCAP |DWC3_OCFG_HNPCAP );are you sure *NO* DWC3 implementation out there is SRP capable and HNP capable?
Quoted 7 lines
Quoted 4 lines
HNP I understand that you want to disable because we're not support full OTG, but SRP should be easy to support and it's also rather handy. In any case, perhaps add a slightly longer comment explaining why you're disabling these?
This is done according to Fig 11.4 in the TRM. IMO it needs to be done even if the controller supports SRP and HNP.
I see, fair enough.
Quoted 8 lines
Quoted 6 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1022
Quoted 3 lines
drivers/usb/dwc3/core.c +3
-0+dwc3_writel (dwc->regs,DWC3_OCFG , reg); +/* OEVT = FFFF */ +dwc3_writel (dwc->regs,DWC3_OEVT , ~0 );hmmm, flushing pending events. Are you sure you can even have them at this point? This should be called after we reset the controller.
This is again as per Fig 11.4 in TRM.
documentation might have made assumptions which don't apply to us :-)
Quoted 11 lines
Quoted 6 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1026
Quoted 4 lines
drivers/usb/dwc3/core.c +4
-0+/* OEVTEN = 0 */ +dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS ); +/* OEVTEN.ConIDStsChngEn = 1. Instead we enable all events */ +dwc3_otg_enable_events (dwc,DWC3_OTG_ALL_EVENTS );oh, disable everything and enable everything right after. What gives?
I did this following Fig 11.4. But there there don't enable all events, so it was a good idea to be on a clean slate by disabling all events first and then only enabling selected events.
Quoted 5 lines
Quoted 3 lines
In any case I think it is good practice. i.e. clear before OR operation? FYI.
dwc3_otg_enable_eventsdoesn't clear the events that are not enabled so if some old event not part ofenable_maskwas enabled it will stay enabled.can't this result in IRQ triggering forever and us not handling it? ;-)
Why should enabling events trigger IRQ? IRQ will trigger only when the event actually happens no?
Quoted 27 lines
Quoted 27 lines
Quoted 26 lines
Quoted 13 lines
drivers/usb/dwc3/core.c +12
-0+/* +* OCTL.PeriMode = 1, OCTL.DevSetHNPEn = 0, OCTL.HstSetHNPEn = 0, +* OCTL.HNPReq = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg |=DWC3_OCTL_PERIMODE ; + reg &= ~(DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HSTSETHNPEN | +DWC3_OCTL_HNPREQ ); +dwc3_writel (dwc->regs,DWC3_OCTL , reg); +} + +/* dwc->lock must be held */ drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1048
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+static int dwc3_drd_start_host (struct dwc3 *dwc,int on,bool skip) +{ +u32 reg; + +/* switch OTG core */ +if (on) { +/* As per Figure 11-10 A-Device Flow Diagram */ +/* OCFG.HNPCap = 0, OCFG.SRPCap = 0 */ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~(DWC3_OCFG_SRPCAP |DWC3_OCFG_HNPCAP );didn't you do this already? Why do you need to do this again?
Quoted 4 lines
Quoted 2 lines
Was blindly following Fig 11-10. Might be necessary whenever we support HNP/SRP. I can get rid of it though if you prefer.
please do, minimal support for now ;-)
OK :).
Quoted 44 lines
Quoted 14 lines
Quoted 13 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1057
Quoted 10 lines
drivers/usb/dwc3/core.c +9
-0+dwc3_writel (dwc->regs,DWC3_OCFG , reg); + +/* +* OCTL.PeriMode=0, OCTL.TermSelDLPulse = 0, +* OCTL.DevSetHNPEn = 0, OCTL.HstSetHNPEn = 0 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg &= ~(DWC3_OCTL_PERIMODE |DWC3_OCTL_TERMSELIDPULSE | +DWC3_OCTL_DEVSETHNPEN |DWC3_OCTL_HSTSETHNPEN );HNP already disabled elsewhere. Why disable it again?
Quoted 1 line
Strictly following TRM. nothing else. What do you want me to do here?
assume your register writes actually stick :-)
Quoted 10 lines
Quoted 10 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1064
Quoted 7 lines
drivers/usb/dwc3/core.c +7
-0+dwc3_writel (dwc->regs,DWC3_OCTL , reg); + +/* +* OCFG.DisPrtPwrCutoff = 0/1 +*/ + reg =dwc3_readl (dwc->regs,DWC3_OCFG ); + reg &= ~DWC3_OCFG_DISPWRCUTTOFF ;^^ one T enough?
Quoted 7 lines
Quoted 3 lines
Review static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1032
Quoted 1 line
(quoted diff) +1
-0+ dwc3_writel(dwc->regs, DWC3_OCFG, reg);should you really always disable port power cutoff ?
If I remember right this should be disabled for non OTG cases else core will turn off VBUS after
A_WAIT_BCONtimeout when port is disconnected.aha, good point :-)
Quoted 6 lines
Quoted 5 lines
Review static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1034
Quoted 2 lines
(quoted diff) +2
-0+ /* start the xHCI host driver */ + if (!skip) {when would skip be true?
Quoted 6 lines
Quoted 1 line
only during system resume.
hmmm, is there a reason for that? I mean, could we live without it for the time being? Seems like all this achieves is avoiding reenumeration of some devices during resume. Do we care from a starting implementation?
At least on AM43x, it was required. without that USB devices plugged in before a system suspend were lost after resume.
I agree on dropping this for now and adding it later.
Quoted 21 lines
Quoted 21 lines
Quoted 20 lines
Quoted 8 lines
drivers/usb/dwc3/core.c +7
-0+ }else { +/* +* Exit from A-device flow as per +* Figure 11-4 OTG Driver Overall Programming Flow +*/ +/* stop the HCD */ +if (!skip) {drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1113
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+spin_unlock (&dwc->lock); +dwc3_host_exit (dwc); +spin_lock (&dwc->lock); + } + +/* +* OEVTEN.OTGADevBHostEndEvntEn=0, OEVTEN.OTGADevHNPChngEvntEn=0 +* OEVTEN.OTGADevSessEndDetEvntEn=0, +* OEVTEN.OTGADevHostEvntEn = 0 +* But we don't disable any OTG events why not?
Quoted 4 lines
Quoted 2 lines
because we kept all of them enabled based on your suggestion last year (unlike what TRM says)
Hmm, I see. I, clearly, forgot what I said. :-p Sorry
np :)
Quoted 52 lines
Quoted 10 lines
Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1118
Quoted 6 lines
drivers/usb/dwc3/core.c +5
-0+*/ + +/* OCTL.HstSetHNPEn = 0, OCTL.PrtPwrCtl=0 */ + reg =dwc3_readl (dwc->regs,DWC3_OCTL ); + reg &= ~(DWC3_OCTL_HSTSETHNPEN |DWC3_OCTL_PRTPWRCTL );disabled elsewhere. Why do it again?
I can optimize it away if you prefer.
we gotta start with an assumption that the HW works. If it doesn't, we quirk it out.
Quoted 9 lines
Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1122
Quoted 4 lines
drivers/usb/dwc3/core.c +4
-0+dwc3_writel (dwc->regs,DWC3_OCTL , reg); + +/* Initialize OTG registers */ +dwc3_otgregs_init (dwc);again you reinitialize everything. Why so many reinitializations? Seems like you were having issues getting this to work and ended up with silly reinitializations and workqueues in an effort to get it working.
Quoted 5 lines
Felipe, last year you told me to strictly follow the TRM programming model. This is what it says to do. Please refer Fig 11.4
I know some things are silly but I deliberately didn't optimize them. If you want to now not strictly follow the TRM I'm fine with that as well.
I see what you're doing now.
Quoted 5 lines
Quoted 2 lines
This patch gives me the impression that the feature hasn't been tested properly. :-s
It is currently undergoing testing for TI release. So far there haven't been any surprises.
good to know
Quoted 13 lines
Quoted 12 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1175
Quoted 7 lines
drivers/usb/dwc3/core.c +7
-0+dwc3_writel (dwc->regs,DWC3_GCTL , reg); + +/* start the Peripheral driver */ +if (dwc->gadget_driver) { +__dwc3_gadget_start (dwc); +if (dwc->gadget_pullup) +dwc3_gadget_run_stop (dwc, true, false);why don't you add/remove the UDC just like you do for the HCD? (you wouldn't add/remove a device, but rather call usb_del_gadget_udc()/usb_add_gadget_udc() directly. Would that clean up some of this?
Quoted 8 lines
Quoted 3 lines
It causes more problems than solving anything.
e.g. An already loaded gadget driver will have to be manually removed and re-loaded to work after a peripheral to host to peripheral mode switch.is that really still true? When we remove the UDC, the currently-loaded gadget driver will be moved to the pending list. Once a UDC is added back, udc-core will bind it again to the UDC.
OK. I need to test this again. As you say, the issue might already have been fixed. Good to know that.
Quoted 38 lines
Quoted 12 lines
Quoted 11 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1270
Quoted 8 lines
drivers/usb/dwc3/core.c +8
-0+dwc3_writel (dwc->regs,DWC3_GUSB2PHYCFG (0 ), reg); + +/* Initialize OTG registers */ +dwc3_otgregs_init (dwc); + +/* force drd state machine update the first time */ + dwc->otg_fsm.b_sess_vld =-1 ; + dwc->otg_fsm.id =-1 ;Does this work if you boot with cable already attached? Both host and peripheral cables?
Quoted 1 line
Yes.
fair enough
Quoted 22 lines
Quoted 22 lines
Quoted 7 lines
drivers/usb/dwc3/core.c +7
-0+static int dwc3_drd_init (struct dwc3 *dwc) +{ +int ret, irq; +unsigned long flags; + +INIT_WORK (&dwc->otg_work, dwc3_drd_work); +drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1298
Quoted 10 lines
drivers/usb/dwc3/core.c +10
-0+ irq =dwc3_otg_get_irq (dwc); +if (irq <0 ) +return irq; + + dwc->otg_irq = irq; + +/* disable all otg irqs */ +dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS ); +/* clear all events */ +dwc3_writel (dwc->regs,DWC3_OEVT , ~0 );this is really odd. You have a bunch of these duplicated chunks of code all over the place...
Quoted 8 lines
Quoted 6 lines
Quoted 3 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1300
Quoted 1 line
drivers/usb/dwc3/core.c +1
-0+irq_set_status_flags (dwc->otg_irq,IRQ_NOAUTOEN );why?
I don't know how to fix this. I have to do this because
dwc3_omapis doing it on the shared IRQ line and the flags must match if we need to share it.hmmm... Then why does
dwc_omapIRQ haveIRQ_NOAUTOENandotg_irqdoesn't?
We're setting IRQ_NOAUTOEN for otg_irq above.
But the problem is that other platforms might not have this set so it will break there. Need to think of a better way how to tackle this.
Quoted 16 lines
Quoted 16 lines
Quoted 15 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1311
Quoted 12 lines
drivers/usb/dwc3/core.c +11
-0+ ret =request_threaded_irq (dwc->otg_irq, dwc3_otg_irq, + dwc3_otg_thread_irq, +IRQF_SHARED ,"dwc3-otg" , dwc); +if (ret) { +dev_err (dwc->dev,"failed to request irq #%d --> %d\n" , + dwc->otg_irq, ret); + ret = -ENODEV ; +return ret; + } + + ret =dwc3_gadget_init (dwc);unconditionally? What if I booted with a micro-A plugged to my port and a USB-stick attached to it?
Quoted 5 lines
Quoted 2 lines
We are not starting the gadget controller though and we want UDC to be initialized anyways so users can load a gadget driver before hand.
Users will be able to load gadget driver and that will be kept in the pending list until a UDC is loaded.
cool.
Quoted 21 lines
Quoted 4 lines
This is another point against using
usb_del_gadget_udc(). The gadget controller is really there and user wants to have a persistant gadget driver loaded between host/peripheral mode switches.see above.
Quoted 11 lines
Quoted 9 lines
drivers/usb/dwc3/gadget.c static int dwc3_gadget_start(struct usb_gadget *g, · line 1838
Quoted 6 lines
drivers/usb/dwc3/gadget.c +1
-1@@ -1827,7 +1835,7 @@ static int dwc3_gadget_start(struct usb_gadget *g,return ret; } -static void __dwc3_gadget_stop (struct dwc3 *dwc) +void __dwc3_gadget_stop (struct dwc3 *dwc)shouldn't have to. Just rely on usb_add/del_gadget_udc()
Please let's not use usb_add/del_gadget_udc(). It causes more trouble for user :)
I can't see why it would :-s
Quoted 8 lines
Quoted 4 lines
gadget_start/stop has been working beautifully with the benefit of user being able to load gadget driver at any time (even when booted with host mode) and not worrying about re-loading it between host/peripheral role swithces.
If that's still necessary, we have a bug in udc-core. That needs to be fixed :-)
Understood. Thanks :)
regards,
-roger
Re: [PATCH v2 3/4] usb: dwc3: add dual-role support
Hi
Quoted 5 lines · Roger Quadros
Quoted 5 lines
Quoted 4 lines
Quoted 2 lines
For something that simple, we wouldn't even need to use OTG FSM layer because that brings no benefit for such a simple requirement.
no no. I think you got it wrong. I'm not using the OTG FSM layer at all :).
Quoted 8 lines
Quoted 5 lines
what are all the
otg_fsmmentions then? Also you have:+ struct
usb_otgotg;
+ structotg_fsmotg_fsm;I'll get rid of them. They aren't really needed. Now I see why you thought I was using the
otg_fsmlayer. :)
fair enough
Quoted 17 lines
Quoted 8 lines
Quoted 7 lines
Quoted 1 line
Can you either confirm or refute the statement above?
The real problem was that if host adapter was removed during a system suspend then while resuming XHCI was locking up like below. This is probably because we're trying to remove/Halt the HCD in the
otg_irq_handlerbefore XHCI driver has resumed?How can we ensure that we call
dwc3_host_exit()only *after* XHCI driver has resumed?Quoted 8 lines
Well, xHCI is our child, so driver model should *already* be guaranteeing that, no? Specially since you're calling this from ->complete() which happens after ->resume() has been called for the entire tree. It's true, however, that dwc3's ->complete() will be called before xhci's ->complete(). Is this the problem you're pointing at? Or do you mean xHCI is runtime suspended (or runtime resuming) while you call
dwc3_host_exit()? If that's the case, then there's a bug in xHCI itself.
Quoted 4 lines
Yes
dwc3->complete()being called beforexhci->complete(), and so HCD being removed beforexhci->complete()causes the lockup.It could be a bug in xHCI driver as well.
I see...
Quoted 8 lines
Quoted 8 lines
Quoted 2 lines
We need a way to mask the OTG events without loosing them while they are masked. Do you know how that could be achieved?
masking doesn't clear events. It just masks them. Look at
gadget.cfor how we do it. Basically, the code we have here is racy, really racy and will cause hard-to-debug lockups. Your code can only work withIRQF_ONESHOT, which we don't want to add back.
Quoted 4 lines
Quoted 2 lines
In any case, to mask events, you set BIT 31 in GEVNTSIZ register. Just copy it from
gadget.c;-)Isn't GEVNTSIZ specific to device side? We're talking about the OTG block here.
that's true, sorry.
Quoted 3 lines
Are you sure that setting bit 31 of GEVNTSIZ will mask
OTG_irq? I don't think so.Note that
OTG_IRQis a separate IRQ line thanPERIPHERAL_IRQ.
man, there's really no way to mask OTG events. This can be bad :-)
John, can you confirm if there's really no way of masking OTG events without loosing them?
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
Quoted 6 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1026
Quoted 4 lines
drivers/usb/dwc3/core.c +4
-0+/* OEVTEN = 0 */ +dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS ); +/* OEVTEN.ConIDStsChngEn = 1. Instead we enable all events */ +dwc3_otg_enable_events (dwc,DWC3_OTG_ALL_EVENTS );oh, disable everything and enable everything right after. What gives?
I did this following Fig 11.4. But there there don't enable all events, so it was a good idea to be on a clean slate by disabling all events first and then only enabling selected events.
Quoted 8 lines
Quoted 5 lines
Quoted 3 lines
In any case I think it is good practice. i.e. clear before OR operation? FYI.
dwc3_otg_enable_eventsdoesn't clear the events that are not enabled so if some old event not part ofenable_maskwas enabled it will stay enabled.can't this result in IRQ triggering forever and us not handling it? ;-)
Why should enabling events trigger IRQ? IRQ will trigger only when the event actually happens no?
heh, right :-) What I mean is that you might enable an interrupt event which you don't clear, because you don't support it or don't handle it, or whatever.
Reserved bits might become non-reserved in the future and so on.
Quoted 13 lines
Quoted 6 lines
Quoted 6 lines
Quoted 5 lines
Review
Quoted 2 lines
(quoted diff) +2
-0+ /* start the xHCI host driver */ + if (!skip) {when would skip be true?
Quoted 6 lines
Quoted 1 line
only during system resume.
hmmm, is there a reason for that? I mean, could we live without it for the time being? Seems like all this achieves is avoiding reenumeration of some devices during resume. Do we care from a starting implementation?
Quoted 4 lines
At least on AM43x, it was required. without that USB devices plugged in before a system suspend were lost after resume.
I agree on dropping this for now and adding it later.
looks like we have another problem which needs to be investigated ;-)
Quoted 17 lines
Quoted 17 lines
Quoted 16 lines
Quoted 4 lines
Quoted 4 lines
drivers/usb/dwc3/core.c +4
-0+dwc3_writel (dwc->regs,DWC3_GCTL , reg); + +/* start the Peripheral driver */ +if (dwc->gadget_driver) {Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1175
Quoted 3 lines
drivers/usb/dwc3/core.c +3
-0+__dwc3_gadget_start (dwc); +if (dwc->gadget_pullup) +dwc3_gadget_run_stop (dwc, true, false);why don't you add/remove the UDC just like you do for the HCD? (you wouldn't add/remove a device, but rather call usb_del_gadget_udc()/usb_add_gadget_udc() directly. Would that clean up some of this?
It causes more problems than solving anything.
e.g. An already loaded gadget driver will have to be manually removed and re-loaded to work after a peripheral to host to peripheral mode switch.
Quoted 7 lines
Quoted 4 lines
is that really still true? When we remove the UDC, the currently-loaded gadget driver will be moved to the pending list. Once a UDC is added back, udc-core will bind it again to the UDC.
OK. I need to test this again. As you say, the issue might already have been fixed. Good to know that.
okay
Quoted 11 lines
Quoted 8 lines
Quoted 6 lines
Quoted 3 lines
drivers/usb/dwc3/core.c static int dwc3_core_get_phy(struct dwc3 *dwc) · line 1300
Quoted 1 line
drivers/usb/dwc3/core.c +1
-0+irq_set_status_flags (dwc->otg_irq,IRQ_NOAUTOEN );why?
I don't know how to fix this. I have to do this because
dwc3_omapis doing it on the shared IRQ line and the flags must match if we need to share it.hmmm... Then why does
dwc_omapIRQ haveIRQ_NOAUTOENandotg_irqdoesn't?We're setting
IRQ_NOAUTOENforotg_irqabove.
But the problem is that other platforms might not have this set so it will break there.
exactly :-)
Quoted 1 line
Need to think of a better way how to tackle this.
okay
Signature · 1 line
balbi
Re: [PATCH v2 3/4] usb: dwc3: add dual-role support
Quoted 59 lines · Felipe Balbi
Hi
Quoted 5 lines · Roger Quadros
Quoted 5 lines
Quoted 4 lines
Quoted 2 lines
For something that simple, we wouldn't even need to use OTG FSM layer because that brings no benefit for such a simple requirement.
no no. I think you got it wrong. I'm not using the OTG FSM layer at all :).
Quoted 8 lines
Quoted 5 lines
what are all the
otg_fsmmentions then? Also you have:+ struct
usb_otgotg;
+ structotg_fsmotg_fsm;I'll get rid of them. They aren't really needed. Now I see why you thought I was using the
otg_fsmlayer. :)fair enough
Quoted 17 lines
Quoted 8 lines
Quoted 7 lines
Quoted 1 line
Can you either confirm or refute the statement above?
The real problem was that if host adapter was removed during a system suspend then while resuming XHCI was locking up like below. This is probably because we're trying to remove/Halt the HCD in the
otg_irq_handlerbefore XHCI driver has resumed?How can we ensure that we call
dwc3_host_exit()only *after* XHCI driver has resumed?Quoted 8 lines
Well, xHCI is our child, so driver model should *already* be guaranteeing that, no? Specially since you're calling this from ->complete() which happens after ->resume() has been called for the entire tree. It's true, however, that dwc3's ->complete() will be called before xhci's ->complete(). Is this the problem you're pointing at? Or do you mean xHCI is runtime suspended (or runtime resuming) while you call
dwc3_host_exit()? If that's the case, then there's a bug in xHCI itself.Quoted 4 lines
Yes
dwc3->complete()being called beforexhci->complete(), and so HCD being removed beforexhci->complete()causes the lockup.It could be a bug in xHCI driver as well.
I see...
Quoted 8 lines
Quoted 8 lines
Quoted 2 lines
We need a way to mask the OTG events without loosing them while they are masked. Do you know how that could be achieved?
masking doesn't clear events. It just masks them. Look at
gadget.cfor how we do it. Basically, the code we have here is racy, really racy and will cause hard-to-debug lockups. Your code can only work withIRQF_ONESHOT, which we don't want to add back.Quoted 4 lines
Quoted 2 lines
In any case, to mask events, you set BIT 31 in GEVNTSIZ register. Just copy it from
gadget.c;-)Isn't GEVNTSIZ specific to device side? We're talking about the OTG block here.
that's true, sorry.
Quoted 8 lines
Quoted 3 lines
Are you sure that setting bit 31 of GEVNTSIZ will mask
OTG_irq? I don't think so.Note that
OTG_IRQis a separate IRQ line thanPERIPHERAL_IRQ.man, there's really no way to mask OTG events. This can be bad :-)
John, can you confirm if there's really no way of masking OTG events without loosing them?
Not sure. I'll have to verify.
If the IP version is 3.00a or higher you could experiment with using interrupt moderation as a global mask.
John
PATCH v2 4/4 usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
In reply to Roger Quadrosdra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
We work around that by bypassing the OTG core and reading the extcon framework directly for ID/VBUS events.
--- Documentation/devicetree/bindings/usb/dwc3.txt | 2 + drivers/usb/dwc3/core.c | 169 ++++++++++++++++++++++++- drivers/usb/dwc3/core.h | 5 + 3 files changed, 170 insertions(+), 6 deletions(-)
Documentation/devicetree/bindings/usb/dwc3.txt +2 -0
@@ -53,6 +53,8 @@ Optional properties: - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ register for post-silicon frame length adjustment when the fladj_30mhz_sdbnd signal is invalid or incorrect. + - extcon: phandle to the USB connector extcon device. If present, extcon + device will be used to get USB cable events instead of OTG controller. - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated.
drivers/usb/dwc3/core.c +163 -6
247 lines not on this page · raw message
drivers/usb/dwc3/core.h +5 -0
@@ -38,6 +38,7 @@#include <linux/usb/otg.h> #include <linux/usb/otg-fsm.h> +#include <linux/extcon.h> #include <linux/workqueue.h> #define DWC3_MSG_MAX 500
@@ -869,6 +870,8 @@ struct dwc3_scratchpad_array {* @current_mode: current mode of operation written to PRTCAPDIR * @otg_work: work struct for otg/dual-role * @otg_needs_host_start: flag that OTG controller needs to start host +* @edev: extcon handle +* @edev_nb: extcon notifier * @fladj: frame length adjustment * @irq_gadget: peripheral controller's IRQ number * @otg_irq: IRQ number for OTG IRQs
@@ -1007,6 +1010,8 @@ struct dwc3 {u32 current_mode;struct work_struct otg_work;bool otg_needs_host_start; +struct extcon_dev *edev; +struct notifier_block edev_nb;enum usb_phy_interface hsphy_mode;
Signature · 1 line
2.7.4
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Quoted 30 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
We work around that by bypassing the OTG core and reading the extcon framework directly for ID/VBUS events.
Signed-off-by Roger Quadros <[email protected]>--- Documentation/devicetree/bindings/usb/dwc3.txt | 2 + drivers/usb/dwc3/core.c | 169 ++++++++++++++++++++++++- drivers/usb/dwc3/core.h | 5 + 3 files changed, 170 insertions(+), 6 deletions(-)Documentation/devicetree/bindings/usb/dwc3.txt +2
-0@@ -53,6 +53,8 @@ Optional properties: - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ register for post-silicon frame length adjustment when the fladj_30mhz_sdbnd signal is invalid or incorrect. + - extcon: phandle to the USB connector extcon device. If present, extcon + device will be used to get USB cable events instead of OTG controller. - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated.drivers/usb/dwc3/core.c +0
-0
[snip]
drivers/usb/dwc3/core.c static int dwc3_probe(struct platform_device *pdev) · line 1732
Quoted 7 lines
drivers/usb/dwc3/core.c +3
-0@@ -1587,6 +1727,14 @@ static int dwc3_probe(struct platform_device *pdev)dwc3_get_properties (dwc); +if (dev->of_node) { +if (of_property_read_bool (dev->of_node,"extcon" )) + dwc->edev =extcon_get_edev_by_phandle (dev,0 );
Don't we want separate edev's for vbus and id ?
One can have separate pins connected to them and in that case we can't get the events out of one pin only.
drivers/usb/dwc3/core.c static int dwc3_probe(struct platform_device *pdev) · line 1735
Quoted 3 lines
drivers/usb/dwc3/core.c +3
-0+ +if (IS_ERR (dwc->edev)) +return PTR_ERR (dwc->edev);
Took me a while to get to this. :)
if (IS_ERR(dwc->edev)) {
ret = PTR_ERR(dwc->edev);
goto err0;
}We want to reset the res->start back to its original offset.
Testing this series currently. Will get back with my results.
Regards
Vivek
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Quoted 34 lines · Vivek Gautam
Quoted 28 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
We work around that by bypassing the OTG core and reading the extcon framework directly for ID/VBUS events.
Signed-off-by Roger Quadros <[email protected]>--- Documentation/devicetree/bindings/usb/dwc3.txt | 2 + drivers/usb/dwc3/core.c | 169 ++++++++++++++++++++++++- drivers/usb/dwc3/core.h | 5 + 3 files changed, 170 insertions(+), 6 deletions(-)Documentation/devicetree/bindings/usb/dwc3.txt +2
-0@@ -53,6 +53,8 @@ Optional properties: - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ register for post-silicon frame length adjustment when the fladj_30mhz_sdbnd signal is invalid or incorrect. + - extcon: phandle to the USB connector extcon device. If present, extcon + device will be used to get USB cable events instead of OTG controller. - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated.drivers/usb/dwc3/core.c +0
-0[snip]
Quoted 10 lines
drivers/usb/dwc3/core.c static int dwc3_probe(struct platform_device *pdev) · line 1730
Quoted 5 lines
drivers/usb/dwc3/core.c +3
-0@@ -1587,6 +1727,14 @@ static int dwc3_probe(struct platform_device *pdev)dwc3_get_properties (dwc); +if (dev->of_node) { +if (of_property_read_bool (dev->of_node,"extcon" )) + dwc->edev =extcon_get_edev_by_phandle (dev,0 );Don't we want separate edev's for vbus and id ?
One can have separate pins connected to them and in that case we can't get the events out of one pin only.
Current extcon-usb-gpio driver supports id and vbus at the same time, that means there are two optional gpios under one extcon node.
Signature · 2 lines
Best Regards, Peter Chen
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Quoted 42 lines · Peter Chen
Quoted 32 lines · Vivek Gautam
Quoted 28 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
We work around that by bypassing the OTG core and reading the extcon framework directly for ID/VBUS events.
Signed-off-by Roger Quadros <[email protected]>--- Documentation/devicetree/bindings/usb/dwc3.txt | 2 + drivers/usb/dwc3/core.c | 169 ++++++++++++++++++++++++- drivers/usb/dwc3/core.h | 5 + 3 files changed, 170 insertions(+), 6 deletions(-)Documentation/devicetree/bindings/usb/dwc3.txt +2
-0@@ -53,6 +53,8 @@ Optional properties: - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ register for post-silicon frame length adjustment when the fladj_30mhz_sdbnd signal is invalid or incorrect. + - extcon: phandle to the USB connector extcon device. If present, extcon + device will be used to get USB cable events instead of OTG controller. - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated.drivers/usb/dwc3/core.c +0
-0[snip]
Quoted 9 lines
drivers/usb/dwc3/core.c static int dwc3_probe(struct platform_device *pdev) · line 1730
Quoted 5 lines
drivers/usb/dwc3/core.c +3
-0@@ -1587,6 +1727,14 @@ static int dwc3_probe(struct platform_device *pdev)dwc3_get_properties (dwc); +if (dev->of_node) { +if (of_property_read_bool (dev->of_node,"extcon" )) + dwc->edev =extcon_get_edev_by_phandle (dev,0 );Don't we want separate edev's for vbus and id ?
One can have separate pins connected to them and in that case we can't get the events out of one pin only.
Quoted 3 lines
Current extcon-usb-gpio driver supports id and vbus at the same time, that means there are two optional gpios under one extcon node.
Right, and we would want to leverage that by providing couple of phandles for vbus and id, and requesting the two in driver.
Regards
Vivek
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
In reply to Vivek Gautam+Chanwoo
Hi Vivek,
Quoted 34 lines · Vivek Gautam
Quoted 28 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
We work around that by bypassing the OTG core and reading the extcon framework directly for ID/VBUS events.
Signed-off-by Roger Quadros <[email protected]>--- Documentation/devicetree/bindings/usb/dwc3.txt | 2 + drivers/usb/dwc3/core.c | 169 ++++++++++++++++++++++++- drivers/usb/dwc3/core.h | 5 + 3 files changed, 170 insertions(+), 6 deletions(-)Documentation/devicetree/bindings/usb/dwc3.txt +2
-0@@ -53,6 +53,8 @@ Optional properties: - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ register for post-silicon frame length adjustment when the fladj_30mhz_sdbnd signal is invalid or incorrect. + - extcon: phandle to the USB connector extcon device. If present, extcon + device will be used to get USB cable events instead of OTG controller. - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated. diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.cindex 619fa7c..b02d911 100644
drivers/usb/dwc3/core.c +0
-0[snip]
Quoted 9 lines
drivers/usb/dwc3/core.c static int dwc3_probe(struct platform_device *pdev) · line 1730
Quoted 5 lines
drivers/usb/dwc3/core.c +2
-0@@ -1587,6 +1727,14 @@ static int dwc3_probe(struct platform_device *pdev)dwc3_get_properties (dwc); + if (dev->of_node) { +if (of_property_read_bool (dev->of_node,"extcon" )) + dwc->edev =extcon_get_edev_by_phandle (dev,0 );Don't we want separate edev's for vbus and id ?
One can have separate pins connected to them and in that case we can't get the events out of one pin only.
Is such kind of hardware really there? Ideally one extcon device represents one connector. So VBUS and ID events of a single USB port should come on one extcon device.
If it doesn't then you need to fix your platforms extcon driver so that it does.
Chanwoo can correct me if I'm wrong on this understanding.
Currently, if VBUS and ID come on GPIOs the extcon-usb-gpio driver takes care of both.
Quoted 7 lines
drivers/usb/dwc3/core.c static int dwc3_probe(struct platform_device *pdev) · line 1735
Quoted 4 lines
drivers/usb/dwc3/core.c +3
-0+ +if (IS_ERR (dwc->edev)) +return PTR_ERR (dwc->edev);Took me a while to get to this. :)
Quoted 10 lines
if (IS_ERR(dwc->edev)) { ret = PTR_ERR(dwc->edev); goto err0; }We want to reset the
res->startback to its original offset.Testing this series currently. Will get back with my results.
Thanks :)
Signature · 2 lines
cheers, -roger
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Hi,
2017-02-24 21:02 GMT+09:00 Roger Quadros <[email protected]>:
Quoted 56 lines
+Chanwoo
Hi Vivek,
Quoted 34 lines · Vivek Gautam
Quoted 28 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
We work around that by bypassing the OTG core and reading the extcon framework directly for ID/VBUS events.
Signed-off-by Roger Quadros <[email protected]>--- Documentation/devicetree/bindings/usb/dwc3.txt | 2 + drivers/usb/dwc3/core.c | 169 ++++++++++++++++++++++++- drivers/usb/dwc3/core.h | 5 + 3 files changed, 170 insertions(+), 6 deletions(-)Documentation/devicetree/bindings/usb/dwc3.txt +2
-0@@ -53,6 +53,8 @@ Optional properties: - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ register for post-silicon frame length adjustment when the fladj_30mhz_sdbnd signal is invalid or incorrect. + - extcon: phandle to the USB connector extcon device. If present, extcon + device will be used to get USB cable events instead of OTG controller. - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated. diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.cindex 619fa7c..b02d911 100644
drivers/usb/dwc3/core.c +0
-0[snip]
Quoted 9 lines
drivers/usb/dwc3/core.c static int dwc3_probe(struct platform_device *pdev) · line 1730
Quoted 5 lines
drivers/usb/dwc3/core.c +2
-0@@ -1587,6 +1727,14 @@ static int dwc3_probe(struct platform_device *pdev)dwc3_get_properties (dwc); + if (dev->of_node) { +if (of_property_read_bool (dev->of_node,"extcon" )) + dwc->edev =extcon_get_edev_by_phandle (dev,0 );Don't we want separate edev's for vbus and id ?
One can have separate pins connected to them and in that case we can't get the events out of one pin only.Is such kind of hardware really there? Ideally one extcon device represents one connector. So VBUS and ID events of a single USB port should come on one extcon device.
If it doesn't then you need to fix your platforms extcon driver so that it does.
Chanwoo can correct me if I'm wrong on this understanding.
Quoted 2 lines
Currently, if VBUS and ID come on GPIOs the extcon-usb-gpio driver takes care of both.
Basically, one extcon device driver can support the multiple external connectors if the detection h/w or port is same.
One extcon device with extcon-usb-gpio.c can support the detection of both ID and VBUS.
But, if there is any issue of h/w schematic, we need to consider how to use the extcon device.
Quoted 23 lines
Quoted 8 lines
drivers/usb/dwc3/core.c static int dwc3_probe(struct platform_device *pdev) · line 1735
Quoted 5 lines
drivers/usb/dwc3/core.c +3
-0+ +if (IS_ERR (dwc->edev)) +return PTR_ERR (dwc->edev);Took me a while to get to this. :)
Quoted 10 lines
if (IS_ERR(dwc->edev)) { ret = PTR_ERR(dwc->edev); goto err0; }We want to reset the
res->startback to its original offset.Testing this series currently. Will get back with my results.
Thanks :)
--
cheers,
-roger
Signature · 3 lines
Best Regards, Chanwoo Choi Samsung Electronics
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
2017-02-25 12:46 GMT+09:00 Chanwoo Choi <[email protected]>:
Quoted 62 lines
Hi,
2017-02-24 21:02 GMT+09:00 Roger Quadros <[email protected]>:
Quoted 56 lines
+Chanwoo
Hi Vivek,
Quoted 34 lines · Vivek Gautam
Quoted 28 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
We work around that by bypassing the OTG core and reading the extcon framework directly for ID/VBUS events.
Signed-off-by Roger Quadros <[email protected]>--- Documentation/devicetree/bindings/usb/dwc3.txt | 2 + drivers/usb/dwc3/core.c | 169 ++++++++++++++++++++++++- drivers/usb/dwc3/core.h | 5 + 3 files changed, 170 insertions(+), 6 deletions(-)Documentation/devicetree/bindings/usb/dwc3.txt +2
-0@@ -53,6 +53,8 @@ Optional properties: - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ register for post-silicon frame length adjustment when the fladj_30mhz_sdbnd signal is invalid or incorrect. + - extcon: phandle to the USB connector extcon device. If present, extcon + device will be used to get USB cable events instead of OTG controller. - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated. diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.cindex 619fa7c..b02d911 100644
drivers/usb/dwc3/core.c +0
-0[snip]
Quoted 9 lines
drivers/usb/dwc3/core.c static int dwc3_probe(struct platform_device *pdev) · line 1730
Quoted 5 lines
drivers/usb/dwc3/core.c +2
-0@@ -1587,6 +1727,14 @@ static int dwc3_probe(struct platform_device *pdev)dwc3_get_properties (dwc); + if (dev->of_node) { +if (of_property_read_bool (dev->of_node,"extcon" )) + dwc->edev =extcon_get_edev_by_phandle (dev,0 );Don't we want separate edev's for vbus and id ?
One can have separate pins connected to them and in that case we can't get the events out of one pin only.Is such kind of hardware really there? Ideally one extcon device represents one connector. So VBUS and ID events of a single USB port should come on one extcon device.
If it doesn't then you need to fix your platforms extcon driver so that it does.
Chanwoo can correct me if I'm wrong on this understanding.Quoted 2 lines
Currently, if VBUS and ID come on GPIOs the extcon-usb-gpio driver takes care of both.
Quoted 8 lines
Basically, one extcon device driver can support the multiple external connectors if the detection h/w or port is same.
One extcon device with
extcon-usb-gpio.ccan support the detection of both ID and VBUS.But, if there is any issue of h/w schematic, we need to consider how to use the extcon device.
Additionally, the extcon-usb-gpio.c use the two gpio pins to detect both ID and VBUS pins. We can check it on documentation[1] of extcon-usb-gpio driver.
Signature · 3 lines
Best Regards, Chanwoo Choi Samsung Electronics
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Quoted 58 lines · Chanwoo Choi
2017-02-25 12:46 GMT+09:00 Chanwoo Choi <[email protected]>:
Quoted 57 lines
Hi,
2017-02-24 21:02 GMT+09:00 Roger Quadros <[email protected]>:
Quoted 54 lines
+Chanwoo
Hi Vivek,
Quoted 34 lines · Vivek Gautam
Quoted 28 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
We work around that by bypassing the OTG core and reading the extcon framework directly for ID/VBUS events.
Signed-off-by Roger Quadros <[email protected]>--- Documentation/devicetree/bindings/usb/dwc3.txt | 2 + drivers/usb/dwc3/core.c | 169 ++++++++++++++++++++++++- drivers/usb/dwc3/core.h | 5 + 3 files changed, 170 insertions(+), 6 deletions(-)Documentation/devicetree/bindings/usb/dwc3.txt +2
-0@@ -53,6 +53,8 @@ Optional properties: - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ register for post-silicon frame length adjustment when the fladj_30mhz_sdbnd signal is invalid or incorrect. + - extcon: phandle to the USB connector extcon device. If present, extcon + device will be used to get USB cable events instead of OTG controller. - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated. diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.cindex 619fa7c..b02d911 100644
drivers/usb/dwc3/core.c +0
-0[snip]
Quoted 9 lines
drivers/usb/dwc3/core.c static int dwc3_probe(struct platform_device *pdev) · line 1730
Quoted 5 lines
drivers/usb/dwc3/core.c +2
-0@@ -1587,6 +1727,14 @@ static int dwc3_probe(struct platform_device *pdev)dwc3_get_properties (dwc); + if (dev->of_node) { +if (of_property_read_bool (dev->of_node,"extcon" )) + dwc->edev =extcon_get_edev_by_phandle (dev,0 );Don't we want separate edev's for vbus and id ?
One can have separate pins connected to them and in that case we can't get the events out of one pin only.Is such kind of hardware really there? Ideally one extcon device represents one connector. So VBUS and ID events of a single USB port should come on one extcon device.
If it doesn't then you need to fix your platforms extcon driver so that it does.
Right, i see it now. One edev for one connector.
Quoted 11 lines
Quoted 11 lines
Quoted 4 lines
Chanwoo can correct me if I'm wrong on this understanding.
Currently, if VBUS and ID come on GPIOs the extcon-usb-gpio driver takes care of both.
Basically, one extcon device driver can support the multiple external connectors if the detection h/w or port is same.
One extcon device with
extcon-usb-gpio.ccan support the detection of both ID and VBUS.
Quoted 8 lines
Quoted 2 lines
But, if there is any issue of h/w schematic, we need to consider how to use the extcon device.
Additionally, the
extcon-usb-gpio.cuse the two gpio pins to detect both ID and VBUS pins. We can check it on documentation[1] of extcon-usb-gpio driver.
Thanks Chanwoo, i understand it now. The extcon-usb-gpio supports both vbus and id gpio, and updates the state of the edev likewise.
Quoted 9 lines
--
Best Regards,
Chanwoo Choi
Samsung Electronics
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
regards
Vivek
Signature · 2 lines
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
In reply to Roger QuadrosHi Roger,
[snip]
Quoted 10 lines
/*
dwc->lockmust be held */
static voiddwc3_otg_core_exit(struct dwc3 *dwc)
{drivers/usb/dwc3/core.c +3
-0+if (dwc->edev) +return ; +/* disable all otg irqs */ dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS );/* clear all events */
drivers/usb/dwc3/core.c static int dwc3_drd_init(struct dwc3 *dwc) · line 1373
Quoted 10 lines
drivers/usb/dwc3/core.c +7
-0@@ -1286,6 +1364,57 @@ static int dwc3_drd_init(struct dwc3 *dwc)INIT_WORK (&dwc->otg_work, dwc3_drd_work); +/* If extcon device is present we don't rely on OTG core for ID event */ +if (dwc->edev) { +int id, vbus; + + dwc->edev_nb.notifier_call = dwc3_drd_notifier; + ret =extcon_register_notifier (dwc->edev,EXTCON_USB , + &dwc->edev_nb);
I recommend that you better to use the devm_extcon_register_notifier()
drivers/usb/dwc3/core.c static int dwc3_drd_init(struct dwc3 *dwc) · line 1380
Quoted 7 lines
drivers/usb/dwc3/core.c +7
-0+if (ret <0 ) { +dev_err (dwc->dev,"Couldn't register USB cable notifier\n" ); +return -ENODEV ; + } + + ret =extcon_register_notifier (dwc->edev,EXTCON_USB_HOST , + &dwc->edev_nb);
Ditto.
[snip]
Signature · 3 lines
Best Regards, Chanwoo Choi Samsung Electronics
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Quoted 17 lines · Chanwoo Choi
Hi Roger,
[snip]
Quoted 13 lines
/*
dwc->lockmust be held */
static voiddwc3_otg_core_exit(struct dwc3 *dwc)
{drivers/usb/dwc3/core.c +3
-0+if (dwc->edev) +return ; +/* disable all otg irqs */ dwc3_otg_disable_events (dwc,DWC3_OTG_ALL_EVENTS );/* clear all events */ @@ -1286,6 +1364,57 @@ static int dwc3_drd_init(struct dwc3 *dwc)INIT_WORK (&dwc->otg_work, dwc3_drd_work);
Quoted 9 lines
drivers/usb/dwc3/core.c static int dwc3_drd_init(struct dwc3 *dwc) · line 1373
Quoted 7 lines
drivers/usb/dwc3/core.c +7
-0+/* If extcon device is present we don't rely on OTG core for ID event */ +if (dwc->edev) { +int id, vbus; + + dwc->edev_nb.notifier_call = dwc3_drd_notifier; + ret =extcon_register_notifier (dwc->edev,EXTCON_USB , + &dwc->edev_nb);I recommend that you better to use the
devm_extcon_register_notifier()
Got it.
Quoted 13 lines
drivers/usb/dwc3/core.c static int dwc3_drd_init(struct dwc3 *dwc) · line 1380
Quoted 8 lines
drivers/usb/dwc3/core.c +7
-0+if (ret <0 ) { +dev_err (dwc->dev,"Couldn't register USB cable notifier\n" ); +return -ENODEV ; + } + + ret =extcon_register_notifier (dwc->edev,EXTCON_USB_HOST , + &dwc->edev_nb);Ditto.
[snip]
Signature · 2 lines
cheers, -roger
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
In reply to Roger QuadrosHi,
Quoted 2 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
yeah, that's not a quirk. DRA7 supports OTGv2, not OTGv3. There was no USB3 when OTGv2 was written.
DRA7 just shouldn't use OTG core altogether. In fact, this is the very thing I've been saying for a long time. Make the simplest implementation possible. The dead simple, does-one-thing-only sort of implementation.
All we need for Dual-Role (without OTG extras) is some input for ID and VBUS, then we add/remove HCD/UDC conditionally and set PRTCAPDIR.
Signature · 1 line
balbi
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Quoted 10 lines · Felipe Balbi
Hi,
Quoted 2 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
yeah, that's not a quirk. DRA7 supports OTGv2, not OTGv3. There was no USB3 when OTGv2 was written.
Quoted 7 lines
DRA7 just shouldn't use OTG core altogether. In fact, this is the very thing I've been saying for a long time. Make the simplest implementation possible. The dead simple, does-one-thing-only sort of implementation.
All we need for Dual-Role (without OTG extras) is some input for ID and VBUS, then we add/remove HCD/UDC conditionally and set PRTCAPDIR.
The catch is that on AM437x there is no way to get ID and VBUS events other than the OTG controller so we have to rely on the OTG controller for that. :(
I agree on the simplicity part. Let's do what minimal is necessary first.
cheers,
-roger
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Hi,
Quoted 11 lines · Roger Quadros
Quoted 11 lines
Quoted 2 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
yeah, that's not a quirk. DRA7 supports OTGv2, not OTGv3. There was no USB3 when OTGv2 was written.
DRA7 just shouldn't use OTG core altogether. In fact, this is the very thing I've been saying for a long time. Make the simplest implementation possible. The dead simple, does-one-thing-only sort of implementation.
Quoted 6 lines
Quoted 3 lines
All we need for Dual-Role (without OTG extras) is some input for ID and VBUS, then we add/remove HCD/UDC conditionally and set PRTCAPDIR.
The catch is that on AM437x there is no way to get ID and VBUS events other than the OTG controller so we have to rely on the OTG controller for that. :(
okay, so AM437x can get OTG interrupts properly. That's fine. We can still do everything we need using code that's already existing in dwc3 if we refactor it a bit and hook it up to the OTG IRQ handler.
Here's what we do:
* First we re-factor all necessary code around so the API for OTG/DRD is resumed to calling:
dwc3_add_udc(dwc);
dwc3_del_udc(dwc);
dwc3_add_hcd(dwc);
dwc3_del_hcd(dwc);the semantics of these should be easy to understand and you can implement each in their respective host.c/gadget.c files.
* Second step is to modify our dwc3_init_mode() (or whatever that function was called, sorry, didn't check) to make sure we have something like:
case OTG:
dwc3_add_udc(dwc);
break;We should *not* add HCD in this case yet.
* After that we add otg.c (or drd.c, no preference) and make that call dwc3_add_udc(dwc) and, also, provide dwc3_add_otg(dwc)/dwc3_del_otg(dwc) calls. Then patch the switch statement above to:
case OTG:
dwc3_add_otg(dwc);
break;Note that at this point, this is simply a direct replacement of dwc3_add_udc() to dwc3_add_otg(). This should maintain current behavior (which is starting with peripheral mode by default), but it should also add support for OTG interrupts to change the mode (from an interrupt thead)
otg_isr()
{
/* don't forget to remove preivous mode if necessary */
if (perimode)
dwc3_add_udc(dwc);
else
dwc3_add_hcd(dwc);
}* The next patch would be to choose default conditionally based on PERIMODE or whatever.
Of course, this is an oversimplified view of reality. You still need to poke around at PRTCAPDIR, etc. But all this can, actually, be prototyped using our "mode" debugfs file. Just make that call dwc3_add/del_udc/hcd() apart from fiddling with PRTCAPDIR in GCTL.
Your first implementation could be just that. Refactoring what needs to be refactored, then patching "mode" debugfs to work properly in that case. Only add otg.c/drd.c after "mode" debugfs file is stable, because then you know what needs to be taken into consideration.
Just to be clear, I'm not saying we should *ONLY* get the debugfs interface for v4.12, I'm saying you should start with that and get that stable and working properly (make an infinite loop constantly changing modes and keep it running over the weekend) before you add support for OTG interrupts, which could come in the same series ;-)
Signature · 1 line
balbi
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Quoted 87 lines · Felipe Balbi
Hi,
Quoted 11 lines · Roger Quadros
Quoted 11 lines
Quoted 2 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
yeah, that's not a quirk. DRA7 supports OTGv2, not OTGv3. There was no USB3 when OTGv2 was written.
DRA7 just shouldn't use OTG core altogether. In fact, this is the very thing I've been saying for a long time. Make the simplest implementation possible. The dead simple, does-one-thing-only sort of implementation.
Quoted 6 lines
Quoted 3 lines
All we need for Dual-Role (without OTG extras) is some input for ID and VBUS, then we add/remove HCD/UDC conditionally and set PRTCAPDIR.
The catch is that on AM437x there is no way to get ID and VBUS events other than the OTG controller so we have to rely on the OTG controller for that. :(
okay, so AM437x can get OTG interrupts properly. That's fine. We can still do everything we need using code that's already existing in dwc3 if we refactor it a bit and hook it up to the OTG IRQ handler.
Here's what we do:
* First we re-factor all necessary code around so the API for OTG/DRD is resumed to calling:
dwc3_add_udc(dwc); dwc3_del_udc(dwc); dwc3_add_hcd(dwc); dwc3_del_hcd(dwc);the semantics of these should be easy to understand and you can implement each in their respective
host.c/gadget.cfiles.* Second step is to modify our
dwc3_init_mode()(or whatever that function was called, sorry, didn't check) to make sure we have something like:case OTG: dwc3_add_udc(dwc); break;We should *not* add HCD in this case yet.
* After that we add
otg.c(ordrd.c, no preference) and make that calldwc3_add_udc(dwc)and, also, provide dwc3_add_otg(dwc)/dwc3_del_otg(dwc) calls. Then patch the switch statement above to:case OTG: dwc3_add_otg(dwc); break;Note that at this point, this is simply a direct replacement of
dwc3_add_udc()todwc3_add_otg(). This should maintain current behavior (which is starting with peripheral mode by default), but it should also add support for OTG interrupts to change the mode (from an interrupt thead)otg_isr() { /* don't forget to remove preivous mode if necessary */ if (perimode) dwc3_add_udc(dwc); else dwc3_add_hcd(dwc); }* The next patch would be to choose default conditionally based on PERIMODE or whatever.
Of course, this is an oversimplified view of reality. You still need to poke around at PRTCAPDIR, etc. But all this can, actually, be prototyped using our "mode" debugfs file. Just make that call dwc3_add/del_udc/hcd() apart from fiddling with PRTCAPDIR in GCTL.
Your first implementation could be just that. Refactoring what needs to be refactored, then patching "mode" debugfs to work properly in that case. Only add
otg.c/drd.cafter "mode" debugfs file is stable, because then you know what needs to be taken into consideration.
Quoted 6 lines
Just to be clear, I'm not saying we should *ONLY* get the debugfs interface for v4.12, I'm saying you should start with that and get that stable and working properly (make an infinite loop constantly changing modes and keep it running over the weekend) before you add support for OTG interrupts, which could come in the same series ;-)
Agree with you. Moreover I could get rid of OTG controller related code and have just debugfs and extcon implementation. We can add the OTG controller bits later.
I agree with you on everything you said except using add/del_gadget_udc. :) I've explained why we can't use del_gadget_udc in the other thread but I'll explain it here again.
1) If we start in host role, usb_add_gadget_udc() won't be called. That means no UDC and user can't load a gadget driver. Typical applications need to have a gadget driver ready *before* the peripheral mode starts so that it can enumerate immediately.
2) If we use usb_del_gadget_udc() when switching to host mode and usb_add_gadget_udc() when switching back to peripheral mode, the previously loaded gadget driver will not be assigned to this UDC. User has to unload and reload the gadget driver.
3) All this becomes even more complex for configfs based gadget driver.
So using stop/start gadget is a much simpler solution really as UDC software side of things remain unchanged and the gadget driver can persist between role switches.
cheers,
-roger
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Hi,
Quoted 95 lines · Roger Quadros
Quoted 84 lines
Quoted 11 lines · Roger Quadros
Quoted 11 lines
Quoted 2 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
yeah, that's not a quirk. DRA7 supports OTGv2, not OTGv3. There was no USB3 when OTGv2 was written.
DRA7 just shouldn't use OTG core altogether. In fact, this is the very thing I've been saying for a long time. Make the simplest implementation possible. The dead simple, does-one-thing-only sort of implementation.
Quoted 6 lines
Quoted 3 lines
All we need for Dual-Role (without OTG extras) is some input for ID and VBUS, then we add/remove HCD/UDC conditionally and set PRTCAPDIR.
The catch is that on AM437x there is no way to get ID and VBUS events other than the OTG controller so we have to rely on the OTG controller for that. :(
okay, so AM437x can get OTG interrupts properly. That's fine. We can still do everything we need using code that's already existing in dwc3 if we refactor it a bit and hook it up to the OTG IRQ handler.
Here's what we do:
* First we re-factor all necessary code around so the API for OTG/DRD is resumed to calling:
dwc3_add_udc(dwc); dwc3_del_udc(dwc); dwc3_add_hcd(dwc); dwc3_del_hcd(dwc);the semantics of these should be easy to understand and you can implement each in their respective
host.c/gadget.cfiles.* Second step is to modify our
dwc3_init_mode()(or whatever that function was called, sorry, didn't check) to make sure we have something like:case OTG: dwc3_add_udc(dwc); break;We should *not* add HCD in this case yet.
* After that we add
otg.c(ordrd.c, no preference) and make that calldwc3_add_udc(dwc)and, also, provide dwc3_add_otg(dwc)/dwc3_del_otg(dwc) calls. Then patch the switch statement above to:case OTG: dwc3_add_otg(dwc); break;Note that at this point, this is simply a direct replacement of
dwc3_add_udc()todwc3_add_otg(). This should maintain current behavior (which is starting with peripheral mode by default), but it should also add support for OTG interrupts to change the mode (from an interrupt thead)otg_isr() { /* don't forget to remove preivous mode if necessary */ if (perimode) dwc3_add_udc(dwc); else dwc3_add_hcd(dwc); }* The next patch would be to choose default conditionally based on PERIMODE or whatever.
Of course, this is an oversimplified view of reality. You still need to poke around at PRTCAPDIR, etc. But all this can, actually, be prototyped using our "mode" debugfs file. Just make that call dwc3_add/del_udc/hcd() apart from fiddling with PRTCAPDIR in GCTL.
Your first implementation could be just that. Refactoring what needs to be refactored, then patching "mode" debugfs to work properly in that case. Only add
otg.c/drd.cafter "mode" debugfs file is stable, because then you know what needs to be taken into consideration.Quoted 6 lines
Just to be clear, I'm not saying we should *ONLY* get the debugfs interface for v4.12, I'm saying you should start with that and get that stable and working properly (make an infinite loop constantly changing modes and keep it running over the weekend) before you add support for OTG interrupts, which could come in the same series ;-)
Agree with you. Moreover I could get rid of OTG controller related code and have just debugfs and extcon implementation. We can add the OTG controller bits later.
Quoted 8 lines
I agree with you on everything you said except using add/del_gadget_udc. :) I've explained why we can't use
del_gadget_udcin the other thread but I'll explain it here again.1) If we start in host role,
usb_add_gadget_udc()won't be called. That means no UDC and user can't load a gadget driver. Typical applications need to have a gadget driver ready *before* the peripheral mode starts so that it can enumerate immediately.
that has changed since you started writing this series :-) gadget drivers are kept in pending list until a UDC is around. I'll get information on that tomorrow, if you require.
Quoted 4 lines
2) If we use
usb_del_gadget_udc()when switching to host mode andusb_add_gadget_udc()when switching back to peripheral mode, the previously loaded gadget driver will not be assigned to this UDC. User has to unload and reload the gadget driver.
that should not be the case anymore, if it is we have a bug in udc-core
Quoted 5 lines
3) All this becomes even more complex for configfs based gadget driver.
So using stop/start gadget is a much simpler solution really as UDC software side of things remain unchanged and the gadget driver can persist between role switches.
I hadn't considered configfs, I'll try this out tomorrow as well.
Signature · 1 line
balbi
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Quoted 103 lines · Felipe Balbi
Hi,
Quoted 99 lines · Roger Quadros
Quoted 84 lines
Quoted 11 lines · Roger Quadros
Quoted 11 lines
Quoted 2 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
yeah, that's not a quirk. DRA7 supports OTGv2, not OTGv3. There was no USB3 when OTGv2 was written.
DRA7 just shouldn't use OTG core altogether. In fact, this is the very thing I've been saying for a long time. Make the simplest implementation possible. The dead simple, does-one-thing-only sort of implementation.
Quoted 6 lines
Quoted 3 lines
All we need for Dual-Role (without OTG extras) is some input for ID and VBUS, then we add/remove HCD/UDC conditionally and set PRTCAPDIR.
The catch is that on AM437x there is no way to get ID and VBUS events other than the OTG controller so we have to rely on the OTG controller for that. :(
okay, so AM437x can get OTG interrupts properly. That's fine. We can still do everything we need using code that's already existing in dwc3 if we refactor it a bit and hook it up to the OTG IRQ handler.
Here's what we do:
* First we re-factor all necessary code around so the API for OTG/DRD is resumed to calling:
dwc3_add_udc(dwc); dwc3_del_udc(dwc); dwc3_add_hcd(dwc); dwc3_del_hcd(dwc);the semantics of these should be easy to understand and you can implement each in their respective
host.c/gadget.cfiles.* Second step is to modify our
dwc3_init_mode()(or whatever that function was called, sorry, didn't check) to make sure we have something like:case OTG: dwc3_add_udc(dwc); break;We should *not* add HCD in this case yet.
* After that we add
otg.c(ordrd.c, no preference) and make that calldwc3_add_udc(dwc)and, also, provide dwc3_add_otg(dwc)/dwc3_del_otg(dwc) calls. Then patch the switch statement above to:case OTG: dwc3_add_otg(dwc); break;Note that at this point, this is simply a direct replacement of
dwc3_add_udc()todwc3_add_otg(). This should maintain current behavior (which is starting with peripheral mode by default), but it should also add support for OTG interrupts to change the mode (from an interrupt thead)otg_isr() { /* don't forget to remove preivous mode if necessary */ if (perimode) dwc3_add_udc(dwc); else dwc3_add_hcd(dwc); }* The next patch would be to choose default conditionally based on PERIMODE or whatever.
Of course, this is an oversimplified view of reality. You still need to poke around at PRTCAPDIR, etc. But all this can, actually, be prototyped using our "mode" debugfs file. Just make that call dwc3_add/del_udc/hcd() apart from fiddling with PRTCAPDIR in GCTL.
Your first implementation could be just that. Refactoring what needs to be refactored, then patching "mode" debugfs to work properly in that case. Only add
otg.c/drd.cafter "mode" debugfs file is stable, because then you know what needs to be taken into consideration.Quoted 6 lines
Just to be clear, I'm not saying we should *ONLY* get the debugfs interface for v4.12, I'm saying you should start with that and get that stable and working properly (make an infinite loop constantly changing modes and keep it running over the weekend) before you add support for OTG interrupts, which could come in the same series ;-)
Agree with you. Moreover I could get rid of OTG controller related code and have just debugfs and extcon implementation. We can add the OTG controller bits later.
I agree with you on everything you said except using add/del_gadget_udc. :) I've explained why we can't use
del_gadget_udcin the other thread but I'll explain it here again.
Quoted 8 lines
Quoted 4 lines
1) If we start in host role,
usb_add_gadget_udc()won't be called. That means no UDC and user can't load a gadget driver. Typical applications need to have a gadget driver ready *before* the peripheral mode starts so that it can enumerate immediately.that has changed since you started writing this series :-) gadget drivers are kept in pending list until a UDC is around. I'll get information on that tomorrow, if you require.
"until a UDC is around" is the key point. If we never call usb_add_gadget_udc() or we call usb_del_gadget_udc() then the UDC is not around right?
Quoted 7 lines
Quoted 5 lines
2) If we use
usb_del_gadget_udc()when switching to host mode andusb_add_gadget_udc()when switching back to peripheral mode, the previously loaded gadget driver will not be assigned to this UDC. User has to unload and reload the gadget driver.that should not be the case anymore, if it is we have a bug in udc-core
OK. good to know.
Quoted 9 lines
Quoted 6 lines
3) All this becomes even more complex for configfs based gadget driver.
So using stop/start gadget is a much simpler solution really as UDC software side of things remain unchanged and the gadget driver can persist between role switches.
I hadn't considered configfs, I'll try this out tomorrow as well.
Al-right, thanks.
cheers,
-roger
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Hi,
Quoted 9 lines · Roger Quadros
Quoted 8 lines
Quoted 5 lines
3) All this becomes even more complex for configfs based gadget driver.
So using stop/start gadget is a much simpler solution really as UDC software side of things remain unchanged and the gadget driver can persist between role switches.
I hadn't considered configfs, I'll try this out tomorrow as well.
Al-right, thanks.
just tested with g_zero.ko and a configfs-based f_mass_storage gadget. All works fine.
Signature · 1 line
balbi
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Quoted 10 lines · Felipe Balbi
Hi,
Quoted 6 lines · Roger Quadros
Quoted 6 lines
Quoted 5 lines
3) All this becomes even more complex for configfs based gadget driver.
So using stop/start gadget is a much simpler solution really as UDC software side of things remain unchanged and the gadget driver can persist between role switches.
Quoted 7 lines
Quoted 3 lines
Quoted 2 lines
I hadn't considered configfs, I'll try this out tomorrow as well.
Al-right, thanks.
just tested with g_zero.ko and a configfs-based
f_mass_storagegadget. All works fine.
Good to know. Thanks for the test.
cheers,
-roger
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
In reply to Felipe BalbiHi,
Quoted 28 lines · Felipe Balbi
Hi,
Quoted 11 lines · Roger Quadros
Quoted 11 lines
Quoted 2 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
yeah, that's not a quirk. DRA7 supports OTGv2, not OTGv3. There was no USB3 when OTGv2 was written.
DRA7 just shouldn't use OTG core altogether. In fact, this is the very thing I've been saying for a long time. Make the simplest implementation possible. The dead simple, does-one-thing-only sort of implementation.
Quoted 6 lines
Quoted 3 lines
All we need for Dual-Role (without OTG extras) is some input for ID and VBUS, then we add/remove HCD/UDC conditionally and set PRTCAPDIR.
The catch is that on AM437x there is no way to get ID and VBUS events other than the OTG controller so we have to rely on the OTG controller for that. :(
okay, so AM437x can get OTG interrupts properly. That's fine. We can still do everything we need using code that's already existing in dwc3 if we refactor it a bit and hook it up to the OTG IRQ handler.
Here's what we do:
Quoted 7 lines
* First we re-factor all necessary code around so the API for OTG/DRD is resumed to calling:
dwc3_add_udc(dwc); dwc3_del_udc(dwc); dwc3_add_hcd(dwc); dwc3_del_hcd(dwc);
Why do we need these new APIs? don't these suffice?
dwc3_gadget_init(dwc); dwc3_gadget_exit(dwc); dwc3_host_init(dwc); dwc3_host_exit(dwc);
Quoted 39 lines
the semantics of these should be easy to understand and you can implement each in their respective
host.c/gadget.cfiles.* Second step is to modify our
dwc3_init_mode()(or whatever that function was called, sorry, didn't check) to make sure we have something like:case OTG: dwc3_add_udc(dwc); break;We should *not* add HCD in this case yet.
* After that we add
otg.c(ordrd.c, no preference) and make that calldwc3_add_udc(dwc)and, also, provide dwc3_add_otg(dwc)/dwc3_del_otg(dwc) calls. Then patch the switch statement above to:case OTG: dwc3_add_otg(dwc); break;Note that at this point, this is simply a direct replacement of
dwc3_add_udc()todwc3_add_otg(). This should maintain current behavior (which is starting with peripheral mode by default), but it should also add support for OTG interrupts to change the mode (from an interrupt thead)otg_isr() { /* don't forget to remove preivous mode if necessary */ if (perimode) dwc3_add_udc(dwc); else dwc3_add_hcd(dwc); }
Quoted 7 lines
* The next patch would be to choose default conditionally based on PERIMODE or whatever.
Of course, this is an oversimplified view of reality. You still need to poke around at PRTCAPDIR, etc. But all this can, actually, be prototyped using our "mode" debugfs file. Just make that call dwc3_add/del_udc/hcd() apart from fiddling with PRTCAPDIR in GCTL.
We also need to ensure that system suspend/resume doesn't break. Mainly if we suspend/resume with UDC removed.
Quoted 6 lines
Your first implementation could be just that. Refactoring what needs to be refactored, then patching "mode" debugfs to work properly in that case. Only add
otg.c/drd.cafter "mode" debugfs file is stable, because then you know what needs to be taken into consideration.
Quoted 6 lines
Just to be clear, I'm not saying we should *ONLY* get the debugfs interface for v4.12, I'm saying you should start with that and get that stable and working properly (make an infinite loop constantly changing modes and keep it running over the weekend) before you add support for OTG interrupts, which could come in the same series ;-)
Just to clarify debugfs mode behaviour.
Currently it is just changing PRTCAPDIR. What we need to do is that if dr_mode == "otg", then we call dwc3_host/gadget_init/exit() accordingly as well.
Does this make sense?
cheers,
-roger
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Hi,
Quoted 32 lines · Roger Quadros
Quoted 24 lines
Quoted 11 lines
Quoted 11 lines
Quoted 2 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
yeah, that's not a quirk. DRA7 supports OTGv2, not OTGv3. There was no USB3 when OTGv2 was written.
DRA7 just shouldn't use OTG core altogether. In fact, this is the very thing I've been saying for a long time. Make the simplest implementation possible. The dead simple, does-one-thing-only sort of implementation.
Quoted 6 lines
Quoted 3 lines
All we need for Dual-Role (without OTG extras) is some input for ID and VBUS, then we add/remove HCD/UDC conditionally and set PRTCAPDIR.
The catch is that on AM437x there is no way to get ID and VBUS events other than the OTG controller so we have to rely on the OTG controller for that. :(
okay, so AM437x can get OTG interrupts properly. That's fine. We can still do everything we need using code that's already existing in dwc3 if we refactor it a bit and hook it up to the OTG IRQ handler.
Here's what we do:
Quoted 7 lines
* First we re-factor all necessary code around so the API for OTG/DRD is resumed to calling:
dwc3_add_udc(dwc); dwc3_del_udc(dwc); dwc3_add_hcd(dwc); dwc3_del_hcd(dwc);
Quoted 5 lines
Why do we need these new APIs? don't these suffice?
dwc3_gadget_init(dwc); dwc3_gadget_exit(dwc); dwc3_host_init(dwc); dwc3_host_exit(dwc);
well, if they do what we want, sure. They suffice.
Quoted 41 lines
Quoted 41 lines
the semantics of these should be easy to understand and you can implement each in their respective
host.c/gadget.cfiles.* Second step is to modify our
dwc3_init_mode()(or whatever that function was called, sorry, didn't check) to make sure we have something like:case OTG: dwc3_add_udc(dwc); break;We should *not* add HCD in this case yet.
* After that we add
otg.c(ordrd.c, no preference) and make that calldwc3_add_udc(dwc)and, also, provide dwc3_add_otg(dwc)/dwc3_del_otg(dwc) calls. Then patch the switch statement above to:case OTG: dwc3_add_otg(dwc); break;Note that at this point, this is simply a direct replacement of
dwc3_add_udc()todwc3_add_otg(). This should maintain current behavior (which is starting with peripheral mode by default), but it should also add support for OTG interrupts to change the mode (from an interrupt thead)otg_isr() { /* don't forget to remove preivous mode if necessary */ if (perimode) dwc3_add_udc(dwc); else dwc3_add_hcd(dwc); }* The next patch would be to choose default conditionally based on PERIMODE or whatever.
Quoted 7 lines
Quoted 4 lines
Of course, this is an oversimplified view of reality. You still need to poke around at PRTCAPDIR, etc. But all this can, actually, be prototyped using our "mode" debugfs file. Just make that call dwc3_add/del_udc/hcd() apart from fiddling with PRTCAPDIR in GCTL.
We also need to ensure that system suspend/resume doesn't break. Mainly if we suspend/resume with UDC removed.
right, why would it break in that case? I'm missing something...
Quoted 12 lines
Quoted 11 lines
Your first implementation could be just that. Refactoring what needs to be refactored, then patching "mode" debugfs to work properly in that case. Only add
otg.c/drd.cafter "mode" debugfs file is stable, because then you know what needs to be taken into consideration.Just to be clear, I'm not saying we should *ONLY* get the debugfs interface for v4.12, I'm saying you should start with that and get that stable and working properly (make an infinite loop constantly changing modes and keep it running over the weekend) before you add support for OTG interrupts, which could come in the same series ;-)
Quoted 6 lines
Just to clarify debugfs mode behaviour.
Currently it is just changing PRTCAPDIR. What we need to do is that if
dr_mode== "otg", then we call dwc3_host/gadget_init/exit() accordingly as well.Does this make sense?
it does.
Signature · 1 line
balbi
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
+Mathias
Quoted 107 lines · Felipe Balbi
Hi,
Quoted 32 lines · Roger Quadros
Quoted 24 lines
Quoted 11 lines
Quoted 11 lines
Quoted 2 lines · Roger Quadros
dra7 OTG core limits the host controller to USB2.0 (high-speed) mode when we're operating in dual-role.
yeah, that's not a quirk. DRA7 supports OTGv2, not OTGv3. There was no USB3 when OTGv2 was written.
DRA7 just shouldn't use OTG core altogether. In fact, this is the very thing I've been saying for a long time. Make the simplest implementation possible. The dead simple, does-one-thing-only sort of implementation.
Quoted 6 lines
Quoted 3 lines
All we need for Dual-Role (without OTG extras) is some input for ID and VBUS, then we add/remove HCD/UDC conditionally and set PRTCAPDIR.
The catch is that on AM437x there is no way to get ID and VBUS events other than the OTG controller so we have to rely on the OTG controller for that. :(
okay, so AM437x can get OTG interrupts properly. That's fine. We can still do everything we need using code that's already existing in dwc3 if we refactor it a bit and hook it up to the OTG IRQ handler.
Here's what we do:
Quoted 7 lines
* First we re-factor all necessary code around so the API for OTG/DRD is resumed to calling:
dwc3_add_udc(dwc); dwc3_del_udc(dwc); dwc3_add_hcd(dwc); dwc3_del_hcd(dwc);Quoted 5 lines
Why do we need these new APIs? don't these suffice?
dwc3_gadget_init(dwc); dwc3_gadget_exit(dwc); dwc3_host_init(dwc); dwc3_host_exit(dwc);well, if they do what we want, sure. They suffice.
Quoted 41 lines
Quoted 41 lines
the semantics of these should be easy to understand and you can implement each in their respective
host.c/gadget.cfiles.* Second step is to modify our
dwc3_init_mode()(or whatever that function was called, sorry, didn't check) to make sure we have something like:case OTG: dwc3_add_udc(dwc); break;We should *not* add HCD in this case yet.
* After that we add
otg.c(ordrd.c, no preference) and make that calldwc3_add_udc(dwc)and, also, provide dwc3_add_otg(dwc)/dwc3_del_otg(dwc) calls. Then patch the switch statement above to:case OTG: dwc3_add_otg(dwc); break;Note that at this point, this is simply a direct replacement of
dwc3_add_udc()todwc3_add_otg(). This should maintain current behavior (which is starting with peripheral mode by default), but it should also add support for OTG interrupts to change the mode (from an interrupt thead)otg_isr() { /* don't forget to remove preivous mode if necessary */ if (perimode) dwc3_add_udc(dwc); else dwc3_add_hcd(dwc); }* The next patch would be to choose default conditionally based on PERIMODE or whatever.
Quoted 7 lines
Quoted 4 lines
Of course, this is an oversimplified view of reality. You still need to poke around at PRTCAPDIR, etc. But all this can, actually, be prototyped using our "mode" debugfs file. Just make that call dwc3_add/del_udc/hcd() apart from fiddling with PRTCAPDIR in GCTL.
We also need to ensure that system suspend/resume doesn't break. Mainly if we suspend/resume with UDC removed.
right, why would it break in that case? I'm missing something...
Quoted 12 lines
Quoted 11 lines
Your first implementation could be just that. Refactoring what needs to be refactored, then patching "mode" debugfs to work properly in that case. Only add
otg.c/drd.cafter "mode" debugfs file is stable, because then you know what needs to be taken into consideration.Just to be clear, I'm not saying we should *ONLY* get the debugfs interface for v4.12, I'm saying you should start with that and get that stable and working properly (make an infinite loop constantly changing modes and keep it running over the weekend) before you add support for OTG interrupts, which could come in the same series ;-)
Quoted 9 lines
Quoted 6 lines
Just to clarify debugfs mode behaviour.
Currently it is just changing PRTCAPDIR. What we need to do is that if
dr_mode== "otg", then we call dwc3_host/gadget_init/exit() accordingly as well.Does this make sense?
it does.
OK. Below is a patch that allows us to use debugfs/mode to do the role switch. Switching from device to host worked fine but I get the following error when switching from host to device.
https://hastebin.com/liluqosewe.xml
cheers,
-roger
---
Quoted 1 line
From
50c49f18474b388d10533eb9f6d04f454fabf687Mon Sep 17 00:00:00 2001
From: Roger Quadros <[email protected]>
Date: Fri, 31 Mar 2017 12:54:13 +0300
Subject: [PATCH] usb: dwc3: make role-switching work with debugfs/mode
If dr_mode == "otg", we start by default in PERIPHERAL mode. Keep track of current role in "current_dr_role" whenever dwc3_set_mode() is called.
When debugfs/mode is changed AND we're in dual-role mode, handle the switch by stopping and starting the respective host/gadget controllers.
--- drivers/usb/dwc3/core.c | 38 +++++++++++++++++++++++------------ drivers/usb/dwc3/core.h | 2 ++ drivers/usb/dwc3/debugfs.c | 49 +++++++++++++++++++++++++++++++++++++++------- 3 files changed, 70 insertions(+), 19 deletions(-)
drivers/usb/dwc3/core.c +26 -12
@@ -108,6 +108,8 @@ void dwc3_set_mode(struct dwc3 *dwc, u32 mode) reg &= ~(DWC3_GCTL_PRTCAPDIR (DWC3_GCTL_PRTCAP_OTG )); reg |=DWC3_GCTL_PRTCAPDIR (mode);dwc3_writel (dwc->regs,DWC3_GCTL , reg); + + dwc->current_dr_role = mode; }u32 dwc3_core_fifo_space (struct dwc3_ep *dep,u8 type)
@@ -862,13 +864,8 @@ static int dwc3_core_init_mode(struct dwc3 *dwc) }break ;case USB_DR_MODE_OTG : - ret =dwc3_host_init (dwc); -if (ret) { -if (ret != -EPROBE_DEFER ) -dev_err (dev,"failed to initialize host\n" ); -return ret; - } - +/* start in peripheral role by default */ +dwc3_set_mode (dwc,DWC3_GCTL_PRTCAP_DEVICE ); ret =dwc3_gadget_init (dwc);if (ret) {if (ret != -EPROBE_DEFER )
@@ -894,8 +891,11 @@ static void dwc3_core_exit_mode(struct dwc3 *dwc)dwc3_host_exit (dwc);break ;case USB_DR_MODE_OTG : -dwc3_host_exit (dwc); -dwc3_gadget_exit (dwc); +/* role might have changed since start */ +if (dwc->current_dr_role ==DWC3_GCTL_PRTCAP_DEVICE ) +dwc3_gadget_exit (dwc); +else if (dwc->current_dr_role ==DWC3_GCTL_PRTCAP_HOST ) +dwc3_host_exit (dwc);break ;default :/* do nothing */
@@ -1209,11 +1209,18 @@ static int dwc3_suspend_common(struct dwc3 *dwc)switch (dwc->dr_mode) {case USB_DR_MODE_PERIPHERAL : -case USB_DR_MODE_OTG :spin_lock_irqsave (&dwc->lock, flags);dwc3_gadget_suspend (dwc);spin_unlock_irqrestore (&dwc->lock, flags);break ; +case USB_DR_MODE_OTG : +/* gadget might not be always present */ +if (dwc->current_dr_role ==DWC3_GCTL_PRTCAP_DEVICE ) { +spin_lock_irqsave (&dwc->lock, flags); +dwc3_gadget_suspend (dwc); +spin_unlock_irqrestore (&dwc->lock, flags); + } +break ;case USB_DR_MODE_HOST :default :/* do nothing */
@@ -1236,11 +1243,18 @@ static int dwc3_resume_common(struct dwc3 *dwc)switch (dwc->dr_mode) {case USB_DR_MODE_PERIPHERAL : -case USB_DR_MODE_OTG :spin_lock_irqsave (&dwc->lock, flags);dwc3_gadget_resume (dwc);spin_unlock_irqrestore (&dwc->lock, flags); -/* FALLTHROUGH */ +break ; +case USB_DR_MODE_OTG : +/* gadget might not be always present */ +if (dwc->current_dr_role ==DWC3_GCTL_PRTCAP_DEVICE ) { +spin_lock_irqsave (&dwc->lock, flags); +dwc3_gadget_resume (dwc); +spin_unlock_irqrestore (&dwc->lock, flags); + } +break ;case USB_DR_MODE_HOST :default :/* do nothing */
drivers/usb/dwc3/core.h +2 -0
@@ -785,6 +785,7 @@ struct dwc3_scratchpad_array {* @maximum_speed: maximum speed requested (mainly for testing purposes) * @revision: revision register contents * @dr_mode: requested mode of operation +* @current_dr_role: current role of operation when in dual-role mode * @hsphy_mode: UTMI phy mode, one of following: * - USBPHY_INTERFACE_MODE_UTMI * - USBPHY_INTERFACE_MODE_UTMIW
@@ -901,6 +902,7 @@ struct dwc3 {size_t regs_size;enum usb_dr_mode dr_mode; +u32 current_dr_role;enum usb_phy_interface hsphy_mode;u32 fladj;
drivers/usb/dwc3/debugfs.c +42 -7
61 lines not on this page · raw message
Signature · 1 line
2.7.4
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Hi,
Quoted 41 lines · Roger Quadros
Quoted 12 lines
Quoted 12 lines
Quoted 11 lines
Your first implementation could be just that. Refactoring what needs to be refactored, then patching "mode" debugfs to work properly in that case. Only add
otg.c/drd.cafter "mode" debugfs file is stable, because then you know what needs to be taken into consideration.Just to be clear, I'm not saying we should *ONLY* get the debugfs interface for v4.12, I'm saying you should start with that and get that stable and working properly (make an infinite loop constantly changing modes and keep it running over the weekend) before you add support for OTG interrupts, which could come in the same series ;-)
Quoted 9 lines
Quoted 6 lines
Just to clarify debugfs mode behaviour.
Currently it is just changing PRTCAPDIR. What we need to do is that if
dr_mode== "otg", then we call dwc3_host/gadget_init/exit() accordingly as well.Does this make sense?
it does.
OK. Below is a patch that allows us to use debugfs/mode to do the role switch. Switching from device to host worked fine but I get the following error when switching from host to device.
https://hastebin.com/liluqosewe.xml
cheers,
-roger---
From50c49f18474b388d10533eb9f6d04f454fabf687Mon Sep 17 00:00:00 2001
From: Roger Quadros <[email protected]>
Date: Fri, 31 Mar 2017 12:54:13 +0300
Subject: [PATCH] usb: dwc3: make role-switching work with debugfs/modeIf
dr_mode== "otg", we start by default in PERIPHERAL mode. Keep track of current role in "current_dr_role" wheneverdwc3_set_mode()is called.
Quoted 5 lines
When debugfs/mode is changed AND we're in dual-role mode, handle the switch by stopping and starting the respective host/gadget controllers.
Signed-off-by Roger Quadros <[email protected]>
I'm assuming you also plan on breaking this down further ;-)
Quoted 30 lines
drivers/usb/dwc3/core.c +4
-7@@ -108,6 +108,8 @@ void dwc3_set_mode(struct dwc3 *dwc, u32 mode) reg &= ~(DWC3_GCTL_PRTCAPDIR (DWC3_GCTL_PRTCAP_OTG )); reg |=DWC3_GCTL_PRTCAPDIR (mode);dwc3_writel (dwc->regs,DWC3_GCTL , reg); + + dwc->current_dr_role = mode; }u32 dwc3_core_fifo_space (struct dwc3_ep *dep,u8 type)@@ -862,13 +864,8 @@ static int dwc3_core_init_mode(struct dwc3 *dwc) }break ;case USB_DR_MODE_OTG : - ret =dwc3_host_init (dwc); -if (ret) { -if (ret != -EPROBE_DEFER ) -dev_err (dev,"failed to initialize host\n" ); -return ret; - } - +/* start in peripheral role by default */ +dwc3_set_mode (dwc,DWC3_GCTL_PRTCAP_DEVICE ); ret =dwc3_gadget_init (dwc);if (ret) {if (ret != -EPROBE_DEFER )
drivers/usb/dwc3/core.c static void dwc3_core_exit_mode(struct dwc3 *dwc) · line 898
Quoted 10 lines
drivers/usb/dwc3/core.c +5
-2@@ -894,8 +891,11 @@ static void dwc3_core_exit_mode(struct dwc3 *dwc)dwc3_host_exit (dwc);break ;case USB_DR_MODE_OTG : -dwc3_host_exit (dwc); -dwc3_gadget_exit (dwc); +/* role might have changed since start */ +if (dwc->current_dr_role ==DWC3_GCTL_PRTCAP_DEVICE ) +dwc3_gadget_exit (dwc); +else if (dwc->current_dr_role ==DWC3_GCTL_PRTCAP_HOST ) +dwc3_host_exit (dwc);
how about patching the respective exit/init functions with something like:
if (dwc->current_dr_role != $my_expected_role)
return 0;
then you can call them without any checks.
Quoted 25 lines
drivers/usb/dwc3/debugfs.c +5
-7@@ -327,19 +327,54 @@ static ssize_t dwc3_mode_write(struct file *file,return -EFAULT ;if (!strncmp (buf,"host" ,4 )) - mode |=DWC3_GCTL_PRTCAP_HOST ; + mode =DWC3_GCTL_PRTCAP_HOST ;if (!strncmp (buf,"device" ,6 )) - mode |=DWC3_GCTL_PRTCAP_DEVICE ; + mode =DWC3_GCTL_PRTCAP_DEVICE ;if (!strncmp (buf,"otg" ,3 )) - mode |=DWC3_GCTL_PRTCAP_OTG ; + mode =DWC3_GCTL_PRTCAP_OTG ; -if (mode) { -spin_lock_irqsave (&dwc->lock, flags); -dwc3_set_mode (dwc, mode); -spin_unlock_irqrestore (&dwc->lock, flags); +if (!mode) +return -EINVAL ;
drivers/usb/dwc3/debugfs.c static ssize_t dwc3_mode_write(struct file *file, · line 349
Quoted 10 lines
drivers/usb/dwc3/debugfs.c +10
-0+ +if (mode == dwc->current_dr_role) + goto exit; + +/* prevent role switching if we're not dual-role */ +if (dwc->dr_mode !=USB_DR_MODE_OTG ) +return -EINVAL ; + +/* stop old role */ +if (dwc->current_dr_role ==DWC3_GCTL_PRTCAP_HOST )
is this your bug? This switch statement only executes when we're in host mode. This means that when you switch to peripheral, you don't exit host. Then when you switch back from peripheral to host, you're going to add the same platform_device again. We're going to have TWO xHCI platform device with the exact same name. When you finally switch again from host to device, then you have issues.
Can you confirm?
Quoted 38 lines
drivers/usb/dwc3/debugfs.c +27
-0+switch (dwc->current_dr_role) { +case DWC3_GCTL_PRTCAP_HOST : +dwc3_host_exit (dwc); +break ; +case DWC3_GCTL_PRTCAP_DEVICE : +dwc3_gadget_exit (dwc); +break ; +default : +break ; + } + +/* switch PRTCAP mode. updates current_dr_role */ +spin_lock_irqsave (&dwc->lock, flags); +dwc3_set_mode (dwc, mode); +spin_unlock_irqrestore (&dwc->lock, flags); + +/* start new role */ +switch (dwc->current_dr_role) { +case DWC3_GCTL_PRTCAP_HOST : +dwc3_host_init (dwc); +break ; +case DWC3_GCTL_PRTCAP_DEVICE : +dwc3_gadget_init (dwc); +break ; +default : +break ; } +exit:return count; }Signature · 6 lines
2.7.4 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Signature · 1 line
balbi
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Quoted 45 lines · Felipe Balbi
Hi,
Quoted 41 lines · Roger Quadros
Quoted 12 lines
Quoted 12 lines
Quoted 11 lines
Your first implementation could be just that. Refactoring what needs to be refactored, then patching "mode" debugfs to work properly in that case. Only add
otg.c/drd.cafter "mode" debugfs file is stable, because then you know what needs to be taken into consideration.Just to be clear, I'm not saying we should *ONLY* get the debugfs interface for v4.12, I'm saying you should start with that and get that stable and working properly (make an infinite loop constantly changing modes and keep it running over the weekend) before you add support for OTG interrupts, which could come in the same series ;-)
Quoted 9 lines
Quoted 6 lines
Just to clarify debugfs mode behaviour.
Currently it is just changing PRTCAPDIR. What we need to do is that if
dr_mode== "otg", then we call dwc3_host/gadget_init/exit() accordingly as well.Does this make sense?
it does.
OK. Below is a patch that allows us to use debugfs/mode to do the role switch. Switching from device to host worked fine but I get the following error when switching from host to device.
https://hastebin.com/liluqosewe.xml
cheers,
-roger---
From50c49f18474b388d10533eb9f6d04f454fabf687Mon Sep 17 00:00:00 2001
From: Roger Quadros <[email protected]>
Date: Fri, 31 Mar 2017 12:54:13 +0300
Subject: [PATCH] usb: dwc3: make role-switching work with debugfs/modeIf
dr_mode== "otg", we start by default in PERIPHERAL mode. Keep track of current role in "current_dr_role" wheneverdwc3_set_mode()is called.
Quoted 7 lines
Quoted 5 lines
When debugfs/mode is changed AND we're in dual-role mode, handle the switch by stopping and starting the respective host/gadget controllers.
Signed-off-by Roger Quadros <[email protected]>I'm assuming you also plan on breaking this down further ;-)
Did you mean I must split this patch into smaller ones?
Quoted 45 lines
Quoted 31 lines
drivers/usb/dwc3/core.c +4
-7@@ -108,6 +108,8 @@ void dwc3_set_mode(struct dwc3 *dwc, u32 mode) reg &= ~(DWC3_GCTL_PRTCAPDIR (DWC3_GCTL_PRTCAP_OTG )); reg |=DWC3_GCTL_PRTCAPDIR (mode);dwc3_writel (dwc->regs,DWC3_GCTL , reg); + + dwc->current_dr_role = mode; }u32 dwc3_core_fifo_space (struct dwc3_ep *dep,u8 type)@@ -862,13 +864,8 @@ static int dwc3_core_init_mode(struct dwc3 *dwc) }break ;case USB_DR_MODE_OTG : - ret =dwc3_host_init (dwc); -if (ret) { -if (ret != -EPROBE_DEFER ) -dev_err (dev,"failed to initialize host\n" ); -return ret; - } - +/* start in peripheral role by default */ +dwc3_set_mode (dwc,DWC3_GCTL_PRTCAP_DEVICE ); ret =dwc3_gadget_init (dwc);if (ret) {if (ret != -EPROBE_DEFER )drivers/usb/dwc3/core.c static void dwc3_core_exit_mode(struct dwc3 *dwc) · line 898
Quoted 10 lines
drivers/usb/dwc3/core.c +5
-2@@ -894,8 +891,11 @@ static void dwc3_core_exit_mode(struct dwc3 *dwc)dwc3_host_exit (dwc);break ;case USB_DR_MODE_OTG : -dwc3_host_exit (dwc); -dwc3_gadget_exit (dwc); +/* role might have changed since start */ +if (dwc->current_dr_role ==DWC3_GCTL_PRTCAP_DEVICE ) +dwc3_gadget_exit (dwc); +else if (dwc->current_dr_role ==DWC3_GCTL_PRTCAP_HOST ) +dwc3_host_exit (dwc);how about patching the respective exit/init functions with something like:
Quoted 4 lines
if (
dwc->current_dr_role!= $my_expected_role)return 0;then you can call them without any checks.
OK.
Quoted 44 lines
Quoted 26 lines
drivers/usb/dwc3/debugfs.c +5
-7@@ -327,19 +327,54 @@ static ssize_t dwc3_mode_write(struct file *file,return -EFAULT ;if (!strncmp (buf,"host" ,4 )) - mode |=DWC3_GCTL_PRTCAP_HOST ; + mode =DWC3_GCTL_PRTCAP_HOST ;if (!strncmp (buf,"device" ,6 )) - mode |=DWC3_GCTL_PRTCAP_DEVICE ; + mode =DWC3_GCTL_PRTCAP_DEVICE ;if (!strncmp (buf,"otg" ,3 )) - mode |=DWC3_GCTL_PRTCAP_OTG ; + mode =DWC3_GCTL_PRTCAP_OTG ; -if (mode) { -spin_lock_irqsave (&dwc->lock, flags); -dwc3_set_mode (dwc, mode); -spin_unlock_irqrestore (&dwc->lock, flags); +if (!mode) +return -EINVAL ;drivers/usb/dwc3/debugfs.c static ssize_t dwc3_mode_write(struct file *file, · line 349
Quoted 10 lines
drivers/usb/dwc3/debugfs.c +10
-0+ +if (mode == dwc->current_dr_role) + goto exit; + +/* prevent role switching if we're not dual-role */ +if (dwc->dr_mode !=USB_DR_MODE_OTG ) +return -EINVAL ; + +/* stop old role */ +if (dwc->current_dr_role ==DWC3_GCTL_PRTCAP_HOST )is this your bug? This switch statement only executes when we're in host mode. This means that when you switch to peripheral, you don't exit host. Then when you switch back from peripheral to host, you're going to add the same
platform_deviceagain. We're going to have TWO xHCI platform device with the exact same name. When you finally switch again from host to device, then you have issues.
Quoted 1 line
Can you confirm?
That was a bug but I still see the issue although only when a mass storage device was plugged in.
I see this other new issue when not using a mass storage device.
root@rockdesk:/sys/kernel/debug/48890000.usb# echo device > mode [ 218.226104] xhci-hcd xhci-hcd.1.auto: remove, state 4 [ 218.231822] usb usb4: USB disconnect, device number 1 [ 218.246973] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered [ 218.252961] xhci-hcd xhci-hcd.1.auto: remove, state 4 [ 218.258347] usb usb3: USB disconnect, device number 1 [ 218.265858] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered [ 218.274312] dwc3 48890000.usb: changing max_speed on rev 5533202a [ 218.282108] kobject (ed120208): tried to init an initialized object, something is seriously wrong. [ 218.291553] CPU: 1 PID: 2025 Comm: bash Not tainted 4.11.0-rc4-00004-g559b2c9 #1285 [ 218.299590] Hardware name: Generic DRA74X (Flattened Device Tree) [ 218.306002] [<c01101ec>] (unwind_backtrace) from [<c010c328>] (show_stack+0x10/0x14) [ 218.314133] [<c010c328>] (show_stack) from [<c04b46b8>] (dump_stack+0xac/0xe0) [ 218.321716] [<c04b46b8>] (dump_stack) from [<c04b5dc8>] (kobject_init+0x78/0x94) [ 218.329484] [<c04b5dc8>] (kobject_init) from [<c0570c98>] (device_initialize+0x20/0xe4) [ 218.337891] [<c0570c98>] (device_initialize) from [<c0573280>] (device_register+0xc/0x18) [ 218.346502] [<c0573280>] (device_register) from [<bf298ce8>] (usb_add_gadget_udc_release+0x88/0x1e8 [udc_core]) [ 218.357153] [<bf298ce8>] (usb_add_gadget_udc_release [udc_core]) from [<bf2c6d68>] (dwc3_gadget_init+0x278/0x6c0 [dwc3]) [ 218.368603] [<bf2c6d68>] (dwc3_gadget_init [dwc3]) from [<bf2cab54>] (dwc3_mode_write+0x178/0x1c4 [dwc3]) [ 218.378668] [<bf2cab54>] (dwc3_mode_write [dwc3]) from [<c04557c4>] (full_proxy_write+0x4c/0x64) [ 218.387897] [<c04557c4>] (full_proxy_write) from [<c02b29d8>] (__vfs_write+0x1c/0x114) [ 218.396206] [<c02b29d8>] (__vfs_write) from [<c02b421c>] (vfs_write+0xa0/0x168) [ 218.403877] [<c02b421c>] (vfs_write) from [<c02b50b4>] (SyS_write+0x44/0x9c) [ 218.411276] [<c02b50b4>] (SyS_write) from [<c0107880>] (ret_fast_syscall+0x0/0x1c) [ 218.419347] ------------[ cut here ]------------ [ 218.424208] WARNING: CPU: 1 PID: 2025 at lib/kobject.c:597 kobject_get+0x48/0x58 [ 218.432018] kobject: '(null)' (ed379018): is not initialized, yet kobject_get() is being called. [ 218.441272] Modules linked in: usb_f_ss_lb g_zero libcomposite xhci_plat_hcd xhci_hcd usbcore dwc3 udc_core evdev snd_soc_davinci_mcasp usb_common snd_soc_edma snd_soc_simple_card m25p80 snd_soc_tlv320aic3x e [ 218.488436] CPU: 1 PID: 2025 Comm: bash Not tainted 4.11.0-rc4-00004-g559b2c9 #1285 [ 218.496470] Hardware name: Generic DRA74X (Flattened Device Tree) [ 218.502870] [<c01101ec>] (unwind_backtrace) from [<c010c328>] (show_stack+0x10/0x14) [ 218.510996] [<c010c328>] (show_stack) from [<c04b46b8>] (dump_stack+0xac/0xe0) [ 218.518579] [<c04b46b8>] (dump_stack) from [<c0136cf0>] (__warn+0xd8/0x104) [ 218.525895] [<c0136cf0>] (__warn) from [<c0136d50>] (warn_slowpath_fmt+0x34/0x44) [ 218.533756] [<c0136d50>] (warn_slowpath_fmt) from [<c04b5e38>] (kobject_get+0x48/0x58) [ 218.542065] [<c04b5e38>] (kobject_get) from [<c0800ef0>] (klist_add_tail+0x18/0x44) [ 218.550114] [<c0800ef0>] (klist_add_tail) from [<c05730dc>] (device_add+0x3d8/0x570) [ 218.558258] [<c05730dc>] (device_add) from [<bf298ce8>] (usb_add_gadget_udc_release+0x88/0x1e8 [udc_core]) [ 218.568428] [<bf298ce8>] (usb_add_gadget_udc_release [udc_core]) from [<bf2c6d68>] (dwc3_gadget_init+0x278/0x6c0 [dwc3]) [ 218.579872] [<bf2c6d68>] (dwc3_gadget_init [dwc3]) from [<bf2cab54>] (dwc3_mode_write+0x178/0x1c4 [dwc3]) [ 218.589939] [<bf2cab54>] (dwc3_mode_write [dwc3]) from [<c04557c4>] (full_proxy_write+0x4c/0x64) [ 218.599165] [<c04557c4>] (full_proxy_write) from [<c02b29d8>] (__vfs_write+0x1c/0x114) [ 218.607480] [<c02b29d8>] (__vfs_write) from [<c02b421c>] (vfs_write+0xa0/0x168) [ 218.615147] [<c02b421c>] (vfs_write) from [<c02b50b4>] (SyS_write+0x44/0x9c) [ 218.622549] [<c02b50b4>] (SyS_write) from [<c0107880>] (ret_fast_syscall+0x0/0x1c) [ 218.630543] ---[ end trace 9b9aa5ff9aaa9cf9 ]--- [ 218.635433] ------------[ cut here ]------------ [ 218.640321] WARNING: CPU: 1 PID: 2025 at lib/refcount.c:114 kobject_get+0x24/0x58 [ 218.648232] refcount_t: increment on 0; use-after-free. [ 218.653718] Modules linked in: usb_f_ss_lb g_zero libcomposite xhci_plat_hcd xhci_hcd usbcore dwc3 udc_core evdev snd_soc_davinci_mcasp usb_common snd_soc_edma snd_soc_simple_card m25p80 snd_soc_tlv320aic3x e [ 218.700873] CPU: 1 PID: 2025 Comm: bash Tainted: G W 4.11.0-rc4-00004-g559b2c9 #1285 [ 218.710180] Hardware name: Generic DRA74X (Flattened Device Tree) [ 218.716583] [<c01101ec>] (unwind_backtrace) from [<c010c328>] (show_stack+0x10/0x14) [ 218.724710] [<c010c328>] (show_stack) from [<c04b46b8>] (dump_stack+0xac/0xe0) [ 218.732296] [<c04b46b8>] (dump_stack) from [<c0136cf0>] (__warn+0xd8/0x104) [ 218.739605] [<c0136cf0>] (__warn) from [<c0136d50>] (warn_slowpath_fmt+0x34/0x44) [ 218.747467] [<c0136d50>] (warn_slowpath_fmt) from [<c04b5e14>] (kobject_get+0x24/0x58) [ 218.755778] [<c04b5e14>] (kobject_get) from [<c0800ef0>] (klist_add_tail+0x18/0x44) [ 218.763820] [<c0800ef0>] (klist_add_tail) from [<c05730dc>] (device_add+0x3d8/0x570) [ 218.771963] [<c05730dc>] (device_add) from [<bf298ce8>] (usb_add_gadget_udc_release+0x88/0x1e8 [udc_core]) [ 218.782128] [<bf298ce8>] (usb_add_gadget_udc_release [udc_core]) from [<bf2c6d68>] (dwc3_gadget_init+0x278/0x6c0 [dwc3]) [ 218.793573] [<bf2c6d68>] (dwc3_gadget_init [dwc3]) from [<bf2cab54>] (dwc3_mode_write+0x178/0x1c4 [dwc3]) [ 218.803634] [<bf2cab54>] (dwc3_mode_write [dwc3]) from [<c04557c4>] (full_proxy_write+0x4c/0x64) [ 218.812862] [<c04557c4>] (full_proxy_write) from [<c02b29d8>] (__vfs_write+0x1c/0x114) [ 218.821166] [<c02b29d8>] (__vfs_write) from [<c02b421c>] (vfs_write+0xa0/0x168) [ 218.828848] [<c02b421c>] (vfs_write) from [<c02b50b4>] (SyS_write+0x44/0x9c) [ 218.836251] [<c02b50b4>] (SyS_write) from [<c0107880>] (ret_fast_syscall+0x0/0x1c) [ 218.844240] ---[ end trace 9b9aa5ff9aaa9cfa ]--- [ 218.850118] zero gadget: Gadget Zero, version: Cinco de Mayo 2008 [ 218.856622] zero gadget: zero ready [ 218.861206] omap_l3_noc 44000000.ocp: L3 application error: target 5 mod:1 (unclearable) [ 218.869779] omap_l3_noc 44000000.ocp: L3 debug error: target 5 mod:1 (unclearable)
Quoted 32 lines
Quoted 32 lines
drivers/usb/dwc3/debugfs.c +27
-0+switch (dwc->current_dr_role) { +case DWC3_GCTL_PRTCAP_HOST : +dwc3_host_exit (dwc); +break ; +case DWC3_GCTL_PRTCAP_DEVICE : +dwc3_gadget_exit (dwc); +break ; +default : +break ; + } + +/* switch PRTCAP mode. updates current_dr_role */ +spin_lock_irqsave (&dwc->lock, flags); +dwc3_set_mode (dwc, mode); +spin_unlock_irqrestore (&dwc->lock, flags); + +/* start new role */ +switch (dwc->current_dr_role) { +case DWC3_GCTL_PRTCAP_HOST : +dwc3_host_init (dwc); +break ; +case DWC3_GCTL_PRTCAP_DEVICE : +dwc3_gadget_init (dwc); +break ; +default : +break ; } +exit:return count; }
Quoted 8 lines
Quoted 7 lines
Signature · 6 lines
2.7.4 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
cheers,
-roger
Re: [PATCH v2 4/4] usb: dwc3: Workaround for super-speed host on dra7 in dual-role mode
Hi,
Quoted 159 lines · Roger Quadros
Quoted 45 lines · Felipe Balbi
Hi,
Quoted 41 lines · Roger Quadros
Quoted 12 lines
Quoted 12 lines
Quoted 11 lines
Your first implementation could be just that. Refactoring what needs to be refactored, then patching "mode" debugfs to work properly in that case. Only add
otg.c/drd.cafter "mode" debugfs file is stable, because then you know what needs to be taken into consideration.Just to be clear, I'm not saying we should *ONLY* get the debugfs interface for v4.12, I'm saying you should start with that and get that stable and working properly (make an infinite loop constantly changing modes and keep it running over the weekend) before you add support for OTG interrupts, which could come in the same series ;-)
Quoted 9 lines
Quoted 6 lines
Just to clarify debugfs mode behaviour.
Currently it is just changing PRTCAPDIR. What we need to do is that if
dr_mode== "otg", then we call dwc3_host/gadget_init/exit() accordingly as well.Does this make sense?
it does.
OK. Below is a patch that allows us to use debugfs/mode to do the role switch. Switching from device to host worked fine but I get the following error when switching from host to device.
https://hastebin.com/liluqosewe.xml
cheers,
-roger---
From50c49f18474b388d10533eb9f6d04f454fabf687Mon Sep 17 00:00:00 2001
From: Roger Quadros <[email protected]>
Date: Fri, 31 Mar 2017 12:54:13 +0300
Subject: [PATCH] usb: dwc3: make role-switching work with debugfs/modeIf
dr_mode== "otg", we start by default in PERIPHERAL mode. Keep track of current role in "current_dr_role" wheneverdwc3_set_mode()is called.Quoted 7 lines
Quoted 5 lines
When debugfs/mode is changed AND we're in dual-role mode, handle the switch by stopping and starting the respective host/gadget controllers.
Signed-off-by Roger Quadros <[email protected]>I'm assuming you also plan on breaking this down further ;-)
Did you mean I must split this patch into smaller ones?
Quoted 45 lines
Quoted 31 lines
drivers/usb/dwc3/core.c +4
-7@@ -108,6 +108,8 @@ void dwc3_set_mode(struct dwc3 *dwc, u32 mode) reg &= ~(DWC3_GCTL_PRTCAPDIR (DWC3_GCTL_PRTCAP_OTG )); reg |=DWC3_GCTL_PRTCAPDIR (mode);dwc3_writel (dwc->regs,DWC3_GCTL , reg); + + dwc->current_dr_role = mode; }u32 dwc3_core_fifo_space (struct dwc3_ep *dep,u8 type)@@ -862,13 +864,8 @@ static int dwc3_core_init_mode(struct dwc3 *dwc) }break ;case USB_DR_MODE_OTG : - ret =dwc3_host_init (dwc); -if (ret) { -if (ret != -EPROBE_DEFER ) -dev_err (dev,"failed to initialize host\n" ); -return ret; - } - +/* start in peripheral role by default */ +dwc3_set_mode (dwc,DWC3_GCTL_PRTCAP_DEVICE ); ret =dwc3_gadget_init (dwc);if (ret) {if (ret != -EPROBE_DEFER )drivers/usb/dwc3/core.c static void dwc3_core_exit_mode(struct dwc3 *dwc) · line 898
Quoted 10 lines
drivers/usb/dwc3/core.c +5
-2@@ -894,8 +891,11 @@ static void dwc3_core_exit_mode(struct dwc3 *dwc)dwc3_host_exit (dwc);break ;case USB_DR_MODE_OTG : -dwc3_host_exit (dwc); -dwc3_gadget_exit (dwc); +/* role might have changed since start */ +if (dwc->current_dr_role ==DWC3_GCTL_PRTCAP_DEVICE ) +dwc3_gadget_exit (dwc); +else if (dwc->current_dr_role ==DWC3_GCTL_PRTCAP_HOST ) +dwc3_host_exit (dwc);how about patching the respective exit/init functions with something like:
Quoted 4 lines
if (
dwc->current_dr_role!= $my_expected_role)return 0;then you can call them without any checks.
OK.
Quoted 44 lines
Quoted 26 lines
drivers/usb/dwc3/debugfs.c +5
-7@@ -327,19 +327,54 @@ static ssize_t dwc3_mode_write(struct file *file,return -EFAULT ;if (!strncmp (buf,"host" ,4 )) - mode |=DWC3_GCTL_PRTCAP_HOST ; + mode =DWC3_GCTL_PRTCAP_HOST ;if (!strncmp (buf,"device" ,6 )) - mode |=DWC3_GCTL_PRTCAP_DEVICE ; + mode =DWC3_GCTL_PRTCAP_DEVICE ;if (!strncmp (buf,"otg" ,3 )) - mode |=DWC3_GCTL_PRTCAP_OTG ; + mode =DWC3_GCTL_PRTCAP_OTG ; -if (mode) { -spin_lock_irqsave (&dwc->lock, flags); -dwc3_set_mode (dwc, mode); -spin_unlock_irqrestore (&dwc->lock, flags); +if (!mode) +return -EINVAL ;drivers/usb/dwc3/debugfs.c static ssize_t dwc3_mode_write(struct file *file, · line 349
Quoted 10 lines
drivers/usb/dwc3/debugfs.c +10
-0+ +if (mode == dwc->current_dr_role) + goto exit; + +/* prevent role switching if we're not dual-role */ +if (dwc->dr_mode !=USB_DR_MODE_OTG ) +return -EINVAL ; + +/* stop old role */ +if (dwc->current_dr_role ==DWC3_GCTL_PRTCAP_HOST )is this your bug? This switch statement only executes when we're in host mode. This means that when you switch to peripheral, you don't exit host. Then when you switch back from peripheral to host, you're going to add the same
platform_deviceagain. We're going to have TWO xHCI platform device with the exact same name. When you finally switch again from host to device, then you have issues.Quoted 1 line
Can you confirm?
That was a bug but I still see the issue although only when a mass storage device was plugged in.
I see this other new issue when not using a mass storage device.
Quoted 9 lines
root@rockdesk:/sys/kernel/debug/48890000.usb# echo device > mode [ 218.226104] xhci-hcd xhci-hcd.1.auto: remove, state 4 [ 218.231822] usb usb4: USB disconnect, device number 1 [ 218.246973] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered [ 218.252961] xhci-hcd xhci-hcd.1.auto: remove, state 4 [ 218.258347] usb usb3: USB disconnect, device number 1 [ 218.265858] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered [ 218.274312] dwc3 48890000.usb: changing max_speed on rev 5533202a [ 218.282108] kobject (ed120208): tried to init an initialized object, something is seriously wrong.
kobj->state_initialized is left set. Need to find a clean way to clear it. As a quick test, you could memset gadget->dev to zero from usb_del_gadget_udc()
Signature · 1 line
balbi
Felipe,
Quoted 8 lines · Roger Quadros
Hi,
We rely on the OTG controller block or Extcon to provide us with VBUS and ID line status via an interrupt.
This is then used to switch the controller between host, peripheral and idle roles based on the following table.
Quoted 8 lines
ID VBUS dual-role state -- ---- --------------- 0 x A_HOST - Host controller active 1 0 B_IDLE - Both Host and Gadget controllers inactive 1 1 B_PERIPHERAL - Gadget controller activeSeries depends on
[1] dwc3 trivial fixes - https://lkml.org/lkml/2017/2/15/204
Would appreciate any feedback on this series. Thanks.
Quoted 22 lines
Changelog:
v2:
- Use extcon device for VBUS/ID events if extcon phandle is present.
- Fix bugs during system suspend/resume.cheers,
-rogerRoger Quadros (4):
usb: dwc3:core.h: add some register definitions
usb: dwc3: omap: don't miss events during suspend/resume
usb: dwc3: add dual-role support
usb: dwc3: Workaround for super-speed host on dra7 in dual-role modeDocumentation/devicetree/bindings/usb/dwc3.txt | 2 + drivers/usb/dwc3/core.c | 752 ++++++++++++++++++++++++- drivers/usb/dwc3/core.h | 131 ++++- drivers/usb/dwc3/dwc3-omap.c | 16 + drivers/usb/dwc3/gadget.c | 18 +- 5 files changed, 895 insertions(+), 24 deletions(-)
Signature · 2 lines
cheers, -roger
Quoted 8 lines · Roger Quadros
Hi,
We rely on the OTG controller block or Extcon to provide us with VBUS and ID line status via an interrupt.
This is then used to switch the controller between host, peripheral and idle roles based on the following table.
Quoted 8 lines
ID VBUS dual-role state -- ---- --------------- 0 x A_HOST - Host controller active 1 0 B_IDLE - Both Host and Gadget controllers inactive 1 1 B_PERIPHERAL - Gadget controller activeSeries depends on
[1] dwc3 trivial fixes - https://lkml.org/lkml/2017/2/15/204
right, you never sent v2 of that though, did you? :-s -ECONFUSED
Signature · 1 line
balbi
Hi,
Quoted 16 lines · Felipe Balbi
Quoted 14 lines · Roger Quadros
Hi,
We rely on the OTG controller block or Extcon to provide us with VBUS and ID line status via an interrupt.
This is then used to switch the controller between host, peripheral and idle roles based on the following table.
ID VBUS dual-role state -- ---- --------------- 0 x A_HOST - Host controller active 1 0 B_IDLE - Both Host and Gadget controllers inactive 1 1 B_PERIPHERAL - Gadget controller active
Quoted 5 lines
Quoted 2 lines
Series depends on
[1] dwc3 trivial fixes - https://lkml.org/lkml/2017/2/15/204right, you never sent v2 of that though, did you? :-s
-ECONFUSED
In that series, the 1st patch is already picked up for v4.11-rc. I sent a v2 of the second patch but it seems it didn't apply cleanly.
https://lkml.org/lkml/2017/2/16/168
I'll send the last 2 patches again based off v4.11-rc4.
cheers,
-roger