Skip to contentSkip to conversation

usb: hub: Fix error loop seen after hub communication errors

PATCH Superseded Guenter Roeck 3 participants 3 messages Mar 16, 2017 – Mar 20, 2017 USB

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 usb: hub: Fix error loop seen after hub communication errors

While stress testing a usb controller using a bind/unbind looop, the following error loop was observed.

usb 7-1.2: new low-speed USB device number 3 using xhci-hcd
usb 7-1.2: hub failed to enable device, error -108
usb 7-1-port2: cannot disable (err = -22)
usb 7-1-port2: couldn't allocate usb_device
usb 7-1-port2: cannot disable (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
** 57 printk messages dropped ** hub 7-1:1.0: activate --> -22
** 82 printk messages dropped ** hub 7-1:1.0: hub_ext_port_status failed (err = -22)

This continues forever. After adding tracebacks into the code, the call sequence leading to this is found to be as follows.

[<ffffffc0007fc8e0>] hub_activate+0x368/0x7b8
[<ffffffc0007fceb4>] hub_resume+0x2c/0x3c
[<ffffffc00080b3b8>] usb_resume_interface.isra.6+0x128/0x158
[<ffffffc00080b5d0>] usb_suspend_both+0x1e8/0x288
[<ffffffc00080c9c4>] usb_runtime_suspend+0x3c/0x98
[<ffffffc0007820a0>] __rpm_callback+0x48/0x7c
[<ffffffc00078217c>] rpm_callback+0xa8/0xd4
[<ffffffc000786234>] rpm_suspend+0x84/0x758
[<ffffffc000786ca4>] rpm_idle+0x2c8/0x498
[<ffffffc000786ed4>] __pm_runtime_idle+0x60/0xac
[<ffffffc00080eba8>] usb_autopm_put_interface+0x6c/0x7c
[<ffffffc000803798>] hub_event+0x10ac/0x12ac
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40

kick_hub_wq() is called from hub_activate() even after failures to communicate with the hub. This results in an endless sequence of hub event -> hub activate -> wq trigger -> hub event -> ...

Provide two solutions for the problem.

- Only trigger the hub event queue if communication with the hub was successful.
- After a suspend failure, only resume already suspended interfaces if the communication with the device is still possible.

Each of the changes fixes the observed problem. Use both to improve robustness.

---
v3: In hub.c, abort immediately if hub_port_status() returns an error.
Since hub_port_status() already logs the error, don't log it again. In device,c, log the error return value from usb_suspend_device() if usb_get_status() failed as well.
Don't check if the hub is still accessible if the error returned from hub_port_status() is -EBUSY.
v2: Instead of not triggering the hub wq after an error to submit an urb,
implement a more complex error detection and handling. Do it in two places. Marked as RFC to determine if one (or both) of those solutions are viable.

 drivers/usb/core/driver.c | 18 ++++++++++++++++++
 drivers/usb/core/hub.c    |  5 ++++-
 2 files changed, 22 insertions(+), 1 deletion(-)
drivers/usb/core/driver.c +18 -0
index cdee5130638b..7ebdf2a4e8fe 100644
@@ -1331,6 +1331,24 @@ static int usb_suspend_both(struct usb_device *udev, pm_message_t msg)
 		 */
 		if (udev->parent && !PMSG_IS_AUTO(msg))
 			status = 0;
+
+		/*
+		 * If the device is inaccessible, don't try to resume
+		 * suspended interfaces and just return the error.
+		 */
+		if (status && status != -EBUSY) {
+			int err;
+			u16 devstat;
+
+			err = usb_get_status(udev, USB_RECIP_DEVICE, 0,
+					     &devstat);
+			if (err) {
+				dev_err(&udev->dev,
+					"Failed to suspend device, error %d\n",
+					status);
+				goto done;
+			}
+		}
 	}
 
 	/* If the suspend failed, resume interfaces that did get suspended */
drivers/usb/core/hub.c +4 -1
index 5a420657f9f7..5ab7cd09e1a4 100644
@@ -1066,6 +1066,9 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type)
 
 		portstatus = portchange = 0;
 		status = hub_port_status(hub, port1, &portstatus, &portchange);
+		if (status)
+			goto abort;
+
 		if (udev || (portstatus & USB_PORT_STAT_CONNECTION))
 			dev_dbg(&port_dev->dev, "status %04x change %04x\n",
 					portstatus, portchange);
@@ -1198,7 +1201,7 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type)
 
 	/* Scan all ports that need attention */
 	kick_hub_wq(hub);
-
+abort:
 	if (type == HUB_INIT2 || type == HUB_INIT3) {
 		/* Allow autosuspend if it was suppressed */
  disconnected:
Signature · 1 line
2.7.4
Acked-by on v3 1/1
#1 lore raw
Quoted 84 lines · Guenter Roeck

While stress testing a usb controller using a bind/unbind looop, the following error loop was observed.

usb 7-1.2: new low-speed USB device number 3 using xhci-hcd
usb 7-1.2: hub failed to enable device, error -108
usb 7-1-port2: cannot disable (err = -22)
usb 7-1-port2: couldn't allocate usb_device
usb 7-1-port2: cannot disable (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
** 57 printk messages dropped ** hub 7-1:1.0: activate --> -22
** 82 printk messages dropped ** hub 7-1:1.0: hub_ext_port_status failed (err = -22)

This continues forever. After adding tracebacks into the code, the call sequence leading to this is found to be as follows.

[<ffffffc0007fc8e0>] hub_activate+0x368/0x7b8
[<ffffffc0007fceb4>] hub_resume+0x2c/0x3c
[<ffffffc00080b3b8>] usb_resume_interface.isra.6+0x128/0x158
[<ffffffc00080b5d0>] usb_suspend_both+0x1e8/0x288
[<ffffffc00080c9c4>] usb_runtime_suspend+0x3c/0x98
[<ffffffc0007820a0>] __rpm_callback+0x48/0x7c
[<ffffffc00078217c>] rpm_callback+0xa8/0xd4
[<ffffffc000786234>] rpm_suspend+0x84/0x758
[<ffffffc000786ca4>] rpm_idle+0x2c8/0x498
[<ffffffc000786ed4>] __pm_runtime_idle+0x60/0xac
[<ffffffc00080eba8>] usb_autopm_put_interface+0x6c/0x7c
[<ffffffc000803798>] hub_event+0x10ac/0x12ac
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40

kick_hub_wq() is called from hub_activate() even after failures to communicate with the hub. This results in an endless sequence of hub event -> hub activate -> wq trigger -> hub event -> ...

Provide two solutions for the problem.

- Only trigger the hub event queue if communication with the hub was successful.
- After a suspend failure, only resume already suspended interfaces if the communication with the device is still possible.

Each of the changes fixes the observed problem. Use both to improve robustness.

---
v3: In hub.c, abort immediately if hub_port_status() returns an error.
Since hub_port_status() already logs the error, don't log it again. In device,c, log the error return value from usb_suspend_device() if usb_get_status() failed as well.
Don't check if the hub is still accessible if the error returned from hub_port_status() is -EBUSY.
v2: Instead of not triggering the hub wq after an error to submit an urb,
implement a more complex error detection and handling. Do it in two places. Marked as RFC to determine if one (or both) of those solutions are viable.

Quoted 3 lines
 drivers/usb/core/driver.c | 18 ++++++++++++++++++
 drivers/usb/core/hub.c    |  5 ++++-
 2 files changed, 22 insertions(+), 1 deletion(-)
Quoted 53 lines
drivers/usb/core/driver.c +18 -0
index cdee5130638b..7ebdf2a4e8fe 100644
@@ -1331,6 +1331,24 @@ static int usb_suspend_both(struct usb_device *udev, pm_message_t msg)
 		 */
 		if (udev->parent && !PMSG_IS_AUTO(msg))
 			status = 0;
+
+		/*
+		 * If the device is inaccessible, don't try to resume
+		 * suspended interfaces and just return the error.
+		 */
+		if (status && status != -EBUSY) {
+			int err;
+			u16 devstat;
+
+			err = usb_get_status(udev, USB_RECIP_DEVICE, 0,
+					     &devstat);
+			if (err) {
+				dev_err(&udev->dev,
+					"Failed to suspend device, error %d\n",
+					status);
+				goto done;
+			}
+		}
 	}
 
 	/* If the suspend failed, resume interfaces that did get suspended */
drivers/usb/core/hub.c +4 -1
index 5a420657f9f7..5ab7cd09e1a4 100644
@@ -1066,6 +1066,9 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type)
 
 		portstatus = portchange = 0;
 		status = hub_port_status(hub, port1, &portstatus, &portchange);
+		if (status)
+			goto abort;
+
 		if (udev || (portstatus & USB_PORT_STAT_CONNECTION))
 			dev_dbg(&port_dev->dev, "status %04x change %04x\n",
 					portstatus, portchange);
@@ -1198,7 +1201,7 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type)
 
 	/* Scan all ports that need attention */
 	kick_hub_wq(hub);
-
+abort:
 	if (type == HUB_INIT2 || type == HUB_INIT3) {
 		/* Allow autosuspend if it was suppressed */
  disconnected:
#2 lore raw
In reply to Guenter Roeck

Hi,

drivers/usb/core/hub.c static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) · line 1204

Quoted 6 lines · Guenter Roeck
drivers/usb/core/hub.c +1 -1
@@ -1198,7 +1201,7 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type)
 
        /* Scan all ports that need attention */
        kick_hub_wq(hub);
-
+abort:

One tiny nit that could be done when applying this patch is to add a space before "abort". Other goto labels in this function are preceded by a space and it's sane to try to match the existing coding convention in the function rather than trying to mix and match.

Other than that this patch seems sane to me, but I am by no means an expert on this code. ;)

-Doug