watchdog: gpio: Add "keep-armed-on-close" feature
Subsystems (2)
PATCH v2 1/1 watchdog: gpio: Add "keep-armed-on-close" feature
From: Sylvain Lemieux <[email protected]>
There is a need to allow a grace period after the watchdog software client has closed. It could be used for syncing the filesystem or allow graceful termination while still providing a hardware reset in case the system has hung.
The "always-running" configuration from device-tree does not provide this since it will automatically keep the hardware watchdog alive as soon as the software client closes (i.e. keep toggling the GPIO line regardless of the state of the soft part of the watchdog).
The "keep-armed-on-close" member in the GPIO watchdog implementation indicates if an expired timeout should cause a reset.
This patch add a new "keep-armed-on-close" device-tree configuration that will keep the watchdog "armed" until the next timeout period after a close. During this period, the hardware watchdog is kept alive. A software watchdog client that wants to provide a grace period before a hard reset can set the timeout before properly closing.
---
* This patch depend on the:
"watchdog: gpio: Convert to use infrastructure triggered keepalives"; ref. https://lkml.org/lkml/2016/2/28/239 (version 8)
Changes from v1 to v2:
* Rebased on-top of the "watchdog: gpio: keepalives" patch.
- Updated the management of the "WDOG_HW_RUNNING" flag.
* Tested with v4.11-rc1.
Documentation/devicetree/bindings/watchdog/gpio-wdt.txt | 3 +++ drivers/watchdog/gpio_wdt.c | 10 ++++++++++ 2 files changed, 13 insertions(+)
Documentation/devicetree/bindings/watchdog/gpio-wdt.txt +3 -0
@@ -17,6 +17,9 @@ Optional Properties: - always-running: If the watchdog timer cannot be disabled, add this flag to have the driver keep toggling the signal without a client. It will only cease to toggle the signal when the device is open and the timeout elapsed. +- keep-armed-on-close: if the watchdog timer need to keep toggling the signal + when close, until the timeout elapsed, add this flag to have the driver + keep toggling the signal, until the timeout elapsed. - timeout-sec: Contains the watchdog timeout in seconds. - start-at-init: Start kicking watchdog as soon as driver is loaded.
drivers/watchdog/gpio_wdt.c +10 -0
@@ -29,6 +29,7 @@ struct gpio_wdt_priv {bool active_low;bool state;bool always_running; +bool keep_armed_on_close;unsigned int hw_algo;struct watchdog_device wdd; };
@@ -78,6 +79,13 @@ static int gpio_wdt_stop(struct watchdog_device *wdd) {struct gpio_wdt_priv *priv =watchdog_get_drvdata (wdd); +if (priv->keep_armed_on_close) { +/* Keep the driver running on close. */ +set_bit (WDOG_HW_RUNNING , &wdd->status); + +return 0 ; + } +if (!priv->always_running) {gpio_wdt_disable (priv);clear_bit (WDOG_HW_RUNNING , &wdd->status);
@@ -148,6 +156,8 @@ static int gpio_wdt_probe(struct platform_device *pdev) priv->always_running =of_property_read_bool (pdev->dev.of_node,"always-running" ); + priv->keep_armed_on_close =of_property_read_bool (pdev->dev.of_node, +"keep-armed-on-close" );watchdog_set_drvdata (&priv->wdd, priv);
Signature · 1 line
2.11.0
ping
Quoted 85 lines · Sylvain Lemieux
From: Sylvain Lemieux <[email protected]>
There is a need to allow a grace period after the watchdog software client has closed. It could be used for syncing the filesystem or allow graceful termination while still providing a hardware reset in case the system has hung.
The "always-running" configuration from device-tree does not provide this since it will automatically keep the hardware watchdog alive as soon as the software client closes (i.e. keep toggling the GPIO line regardless of the state of the soft part of the watchdog).
The "keep-armed-on-close" member in the GPIO watchdog implementation indicates if an expired timeout should cause a reset.
This patch add a new "keep-armed-on-close" device-tree configuration that will keep the watchdog "armed" until the next timeout period after a close. During this period, the hardware watchdog is kept alive. A software watchdog client that wants to provide a grace period before a hard reset can set the timeout before properly closing.
Signed-off-by Sylvain Lemieux <[email protected]>---
* This patch depend on the:
"watchdog: gpio: Convert to use infrastructure triggered keepalives"; ref. https://lkml.org/lkml/2016/2/28/239 (version 8)Changes from v1 to v2:
* Rebased on-top of the "watchdog: gpio: keepalives" patch.
- Updated the management of the "WDOG_HW_RUNNING" flag.
* Tested with v4.11-rc1.Documentation/devicetree/bindings/watchdog/gpio-wdt.txt | 3 +++ drivers/watchdog/gpio_wdt.c | 10 ++++++++++ 2 files changed, 13 insertions(+)Documentation/devicetree/bindings/watchdog/gpio-wdt.txt +3
-0@@ -17,6 +17,9 @@ Optional Properties: - always-running: If the watchdog timer cannot be disabled, add this flag to have the driver keep toggling the signal without a client. It will only cease to toggle the signal when the device is open and the timeout elapsed. +- keep-armed-on-close: if the watchdog timer need to keep toggling the signal + when close, until the timeout elapsed, add this flag to have the driver + keep toggling the signal, until the timeout elapsed. - timeout-sec: Contains the watchdog timeout in seconds. - start-at-init: Start kicking watchdog as soon as driver is loaded.drivers/watchdog/gpio_wdt.c +10
-0@@ -29,6 +29,7 @@ struct gpio_wdt_priv {bool active_low;bool state;bool always_running; +bool keep_armed_on_close;unsigned int hw_algo;struct watchdog_device wdd; };@@ -78,6 +79,13 @@ static int gpio_wdt_stop(struct watchdog_device *wdd) {struct gpio_wdt_priv *priv =watchdog_get_drvdata (wdd); +if (priv->keep_armed_on_close) { +/* Keep the driver running on close. */ +set_bit (WDOG_HW_RUNNING , &wdd->status); + +return 0 ; + } +if (!priv->always_running) {gpio_wdt_disable (priv);clear_bit (WDOG_HW_RUNNING , &wdd->status);@@ -148,6 +156,8 @@ static int gpio_wdt_probe(struct platform_device *pdev) priv->always_running =of_property_read_bool (pdev->dev.of_node,"always-running" ); + priv->keep_armed_on_close =of_property_read_bool (pdev->dev.of_node, +"keep-armed-on-close" );watchdog_set_drvdata (&priv->wdd, priv);
Guenter Roeck
maintainerQuoted 12 lines · Sylvain Lemieux
From: Sylvain Lemieux <[email protected]>
There is a need to allow a grace period after the watchdog software client has closed. It could be used for syncing the filesystem or allow graceful termination while still providing a hardware reset in case the system has hung.
The "always-running" configuration from device-tree does not provide this since it will automatically keep the hardware watchdog alive as soon as the software client closes (i.e. keep toggling the GPIO line regardless of the state of the soft part of the watchdog).
Quoted 9 lines
The "keep-armed-on-close" member in the GPIO watchdog implementation indicates if an expired timeout should cause a reset.
This patch add a new "keep-armed-on-close" device-tree configuration that will keep the watchdog "armed" until the next timeout period after a close. During this period, the hardware watchdog is kept alive. A software watchdog client that wants to provide a grace period before a hard reset can set the timeout before properly closing.
The description doesn't match what the code actually does, at least from an infrastructure perspective. The infrastructure would just keep it running.
What you are really asking for is something the infrastructure should possibly do by itself automatically: To keep pinging a HW watchdog after close until the configured (software) timeout period expires. This would be in line with expectations.
Also, I seem to recall that the gpio_wdt patch this relies on has a problem if the watchdog is opened and closed repeatedly. It is still on my task list to track this down.
Guenter
Quoted 65 lines
Signed-off-by Sylvain Lemieux <[email protected]>---
* This patch depend on the:
"watchdog: gpio: Convert to use infrastructure triggered keepalives"; ref. https://lkml.org/lkml/2016/2/28/239 (version 8)Changes from v1 to v2:
* Rebased on-top of the "watchdog: gpio: keepalives" patch.
- Updated the management of the "WDOG_HW_RUNNING" flag.
* Tested with v4.11-rc1.Documentation/devicetree/bindings/watchdog/gpio-wdt.txt | 3 +++ drivers/watchdog/gpio_wdt.c | 10 ++++++++++ 2 files changed, 13 insertions(+)Documentation/devicetree/bindings/watchdog/gpio-wdt.txt +3
-0@@ -17,6 +17,9 @@ Optional Properties: - always-running: If the watchdog timer cannot be disabled, add this flag to have the driver keep toggling the signal without a client. It will only cease to toggle the signal when the device is open and the timeout elapsed. +- keep-armed-on-close: if the watchdog timer need to keep toggling the signal + when close, until the timeout elapsed, add this flag to have the driver + keep toggling the signal, until the timeout elapsed. - timeout-sec: Contains the watchdog timeout in seconds. - start-at-init: Start kicking watchdog as soon as driver is loaded.drivers/watchdog/gpio_wdt.c +10
-0@@ -29,6 +29,7 @@ struct gpio_wdt_priv {bool active_low;bool state;bool always_running; +bool keep_armed_on_close;unsigned int hw_algo;struct watchdog_device wdd; };@@ -78,6 +79,13 @@ static int gpio_wdt_stop(struct watchdog_device *wdd) {struct gpio_wdt_priv *priv =watchdog_get_drvdata (wdd); +if (priv->keep_armed_on_close) { +/* Keep the driver running on close. */ +set_bit (WDOG_HW_RUNNING , &wdd->status); + +return 0 ; + } +if (!priv->always_running) {gpio_wdt_disable (priv);clear_bit (WDOG_HW_RUNNING , &wdd->status);@@ -148,6 +156,8 @@ static int gpio_wdt_probe(struct platform_device *pdev) priv->always_running =of_property_read_bool (pdev->dev.of_node,"always-running" ); + priv->keep_armed_on_close =of_property_read_bool (pdev->dev.of_node, +"keep-armed-on-close" );watchdog_set_drvdata (&priv->wdd, priv);
Hi,
Quoted 23 lines · Guenter Roeck
Quoted 12 lines · Sylvain Lemieux
From: Sylvain Lemieux <[email protected]>
There is a need to allow a grace period after the watchdog software client has closed. It could be used for syncing the filesystem or allow graceful termination while still providing a hardware reset in case the system has hung.
The "always-running" configuration from device-tree does not provide this since it will automatically keep the hardware watchdog alive as soon as the software client closes (i.e. keep toggling the GPIO line regardless of the state of the soft part of the watchdog).
Quoted 9 lines
The "keep-armed-on-close" member in the GPIO watchdog implementation indicates if an expired timeout should cause a reset.
This patch add a new "keep-armed-on-close" device-tree configuration that will keep the watchdog "armed" until the next timeout period after a close. During this period, the hardware watchdog is kept alive. A software watchdog client that wants to provide a grace period before a hard reset can set the timeout before properly closing.
Quoted 3 lines
The description doesn't match what the code actually does, at least from an infrastructure perspective. The infrastructure would just keep it running.
I will need to send a new version with an updated description;
I did not update the description after this patch was rebased on-top of the "watchdog: gpio: keepalives" patch.
Quoted 8 lines
What you are really asking for is something the infrastructure should possibly do by itself automatically: To keep pinging a HW watchdog after close until the configured (software) timeout period expires. This would be in line with expectations.
Also, I seem to recall that the
gpio_wdtpatch this relies on has a problem if the watchdog is opened and closed repeatedly. It is still on my task list to track this down.
The original "watchdog: gpio: keepalives" patch did not have any issue. I think this patch should be apply mainline.
The problem was related to the management of the WDOG_HW_RUNNING flag (updated in version 2 of this patch) and an issue in the test program on our lpc32xx platform (also using pnx4008 watchdog) during the initial testing with kernel 4.9.
Sylvain
Quoted 69 lines
Guenter
Quoted 65 lines
Signed-off-by Sylvain Lemieux <[email protected]>---
* This patch depend on the:
"watchdog: gpio: Convert to use infrastructure triggered keepalives"; ref. https://lkml.org/lkml/2016/2/28/239 (version 8)Changes from v1 to v2:
* Rebased on-top of the "watchdog: gpio: keepalives" patch.
- Updated the management of the "WDOG_HW_RUNNING" flag.
* Tested with v4.11-rc1.Documentation/devicetree/bindings/watchdog/gpio-wdt.txt | 3 +++ drivers/watchdog/gpio_wdt.c | 10 ++++++++++ 2 files changed, 13 insertions(+)Documentation/devicetree/bindings/watchdog/gpio-wdt.txt +3
-0@@ -17,6 +17,9 @@ Optional Properties: - always-running: If the watchdog timer cannot be disabled, add this flag to have the driver keep toggling the signal without a client. It will only cease to toggle the signal when the device is open and the timeout elapsed. +- keep-armed-on-close: if the watchdog timer need to keep toggling the signal + when close, until the timeout elapsed, add this flag to have the driver + keep toggling the signal, until the timeout elapsed. - timeout-sec: Contains the watchdog timeout in seconds. - start-at-init: Start kicking watchdog as soon as driver is loaded.drivers/watchdog/gpio_wdt.c +10
-0@@ -29,6 +29,7 @@ struct gpio_wdt_priv {bool active_low;bool state;bool always_running; +bool keep_armed_on_close;unsigned int hw_algo;struct watchdog_device wdd; };@@ -78,6 +79,13 @@ static int gpio_wdt_stop(struct watchdog_device *wdd) {struct gpio_wdt_priv *priv =watchdog_get_drvdata (wdd); +if (priv->keep_armed_on_close) { +/* Keep the driver running on close. */ +set_bit (WDOG_HW_RUNNING , &wdd->status); + +return 0 ; + } +if (!priv->always_running) {gpio_wdt_disable (priv);clear_bit (WDOG_HW_RUNNING , &wdd->status);@@ -148,6 +156,8 @@ static int gpio_wdt_probe(struct platform_device *pdev) priv->always_running =of_property_read_bool (pdev->dev.of_node,"always-running" ); + priv->keep_armed_on_close =of_property_read_bool (pdev->dev.of_node, +"keep-armed-on-close" );watchdog_set_drvdata (&priv->wdd, priv);
Quoted 26 lines · Sylvain Lemieux
Hi,
Quoted 23 lines · Guenter Roeck
Quoted 21 lines · Sylvain Lemieux
From: Sylvain Lemieux <[email protected]>
There is a need to allow a grace period after the watchdog software client has closed. It could be used for syncing the filesystem or allow graceful termination while still providing a hardware reset in case the system has hung.
The "always-running" configuration from device-tree does not provide this since it will automatically keep the hardware watchdog alive as soon as the software client closes (i.e. keep toggling the GPIO line regardless of the state of the soft part of the watchdog).
The "keep-armed-on-close" member in the GPIO watchdog implementation indicates if an expired timeout should cause a reset.
This patch add a new "keep-armed-on-close" device-tree configuration that will keep the watchdog "armed" until the next timeout period after a close. During this period, the hardware watchdog is kept alive. A software watchdog client that wants to provide a grace period before a hard reset can set the timeout before properly closing.
Quoted 5 lines
Quoted 3 lines
The description doesn't match what the code actually does, at least from an infrastructure perspective. The infrastructure would just keep it running.
I will need to send a new version with an updated description;
I will submit v3 later today or tomorrow.
Quoted 8 lines
I did not update the description after this patch was rebased on-top of the "watchdog: gpio: keepalives" patch.
Quoted 5 lines
What you are really asking for is something the infrastructure should possibly do by itself automatically: To keep pinging a HW watchdog after close until the configured (software) timeout period expires. This would be in line with expectations.
Do you want me to work on a generic version for this option?
Sylvain
Quoted 4 lines
Quoted 3 lines
Also, I seem to recall that the
gpio_wdtpatch this relies on has a problem if the watchdog is opened and closed repeatedly. It is still on my task list to track this down.
[...]
Quoted 73 lines
Sylvain
Quoted 69 lines
Guenter
Quoted 65 lines
Signed-off-by Sylvain Lemieux <[email protected]>---
* This patch depend on the:
"watchdog: gpio: Convert to use infrastructure triggered keepalives"; ref. https://lkml.org/lkml/2016/2/28/239 (version 8)Changes from v1 to v2:
* Rebased on-top of the "watchdog: gpio: keepalives" patch.
- Updated the management of the "WDOG_HW_RUNNING" flag.
* Tested with v4.11-rc1.Documentation/devicetree/bindings/watchdog/gpio-wdt.txt | 3 +++ drivers/watchdog/gpio_wdt.c | 10 ++++++++++ 2 files changed, 13 insertions(+)Documentation/devicetree/bindings/watchdog/gpio-wdt.txt +3
-0@@ -17,6 +17,9 @@ Optional Properties: - always-running: If the watchdog timer cannot be disabled, add this flag to have the driver keep toggling the signal without a client. It will only cease to toggle the signal when the device is open and the timeout elapsed. +- keep-armed-on-close: if the watchdog timer need to keep toggling the signal + when close, until the timeout elapsed, add this flag to have the driver + keep toggling the signal, until the timeout elapsed. - timeout-sec: Contains the watchdog timeout in seconds. - start-at-init: Start kicking watchdog as soon as driver is loaded.drivers/watchdog/gpio_wdt.c +10
-0@@ -29,6 +29,7 @@ struct gpio_wdt_priv {bool active_low;bool state;bool always_running; +bool keep_armed_on_close;unsigned int hw_algo;struct watchdog_device wdd; };@@ -78,6 +79,13 @@ static int gpio_wdt_stop(struct watchdog_device *wdd) {struct gpio_wdt_priv *priv =watchdog_get_drvdata (wdd); +if (priv->keep_armed_on_close) { +/* Keep the driver running on close. */ +set_bit (WDOG_HW_RUNNING , &wdd->status); + +return 0 ; + } +if (!priv->always_running) {gpio_wdt_disable (priv);clear_bit (WDOG_HW_RUNNING , &wdd->status);@@ -148,6 +156,8 @@ static int gpio_wdt_probe(struct platform_device *pdev) priv->always_running =of_property_read_bool (pdev->dev.of_node,"always-running" ); + priv->keep_armed_on_close =of_property_read_bool (pdev->dev.of_node, +"keep-armed-on-close" );watchdog_set_drvdata (&priv->wdd, priv);
Guenter Roeck
maintainerQuoted 37 lines · Sylvain Lemieux
Quoted 26 lines · Sylvain Lemieux
Hi,
Quoted 23 lines · Guenter Roeck
Quoted 21 lines · Sylvain Lemieux
From: Sylvain Lemieux <[email protected]>
There is a need to allow a grace period after the watchdog software client has closed. It could be used for syncing the filesystem or allow graceful termination while still providing a hardware reset in case the system has hung.
The "always-running" configuration from device-tree does not provide this since it will automatically keep the hardware watchdog alive as soon as the software client closes (i.e. keep toggling the GPIO line regardless of the state of the soft part of the watchdog).
The "keep-armed-on-close" member in the GPIO watchdog implementation indicates if an expired timeout should cause a reset.
This patch add a new "keep-armed-on-close" device-tree configuration that will keep the watchdog "armed" until the next timeout period after a close. During this period, the hardware watchdog is kept alive. A software watchdog client that wants to provide a grace period before a hard reset can set the timeout before properly closing.
Quoted 5 lines
Quoted 3 lines
The description doesn't match what the code actually does, at least from an infrastructure perspective. The infrastructure would just keep it running.
I will need to send a new version with an updated description;
I will submit v3 later today or tomorrow.
Quoted 3 lines
I did not update the description after this patch was rebased on-top of the "watchdog: gpio: keepalives" patch.
Quoted 7 lines
Quoted 5 lines
Quoted 5 lines
What you are really asking for is something the infrastructure should possibly do by itself automatically: To keep pinging a HW watchdog after close until the configured (software) timeout period expires. This would be in line with expectations.
Do you want me to work on a generic version for this option?
I am not sure I understand the value of the current version (as implemented) in the first place. It seems to be similar to "always-running", with the exception that it doesn't start the watchdog immediately when loading the module. That means it protects the system against hard lockups, but only if the watchdog was opened at least once. That just seems odd, and you'll have to explain the benefit over "always-running", and why it would make sense to have such a selective protection.
Note that devicetree property changes need to be Acked by DT maintainers.
Having said that, if what you want is what the description says, not what is implemented, I'll be happy to accept a patch to change the infrastructure accordingly.
Thanks,
Guenter
Quoted 87 lines
Sylvain
Quoted 4 lines
Quoted 3 lines
Also, I seem to recall that the
gpio_wdtpatch this relies on has a problem if the watchdog is opened and closed repeatedly. It is still on my task list to track this down.[...]
Quoted 73 lines
Sylvain
Quoted 69 lines
Guenter
Quoted 65 lines
Signed-off-by Sylvain Lemieux <[email protected]>---
* This patch depend on the:"watchdog: gpio: Convert to use infrastructure triggered keepalives"; ref. https://lkml.org/lkml/2016/2/28/239 (version 8)Changes from v1 to v2:
* Rebased on-top of the "watchdog: gpio: keepalives" patch.
- Updated the management of the "WDOG_HW_RUNNING" flag.
* Tested with v4.11-rc1.Documentation/devicetree/bindings/watchdog/gpio-wdt.txt | 3 +++ drivers/watchdog/gpio_wdt.c | 10 ++++++++++ 2 files changed, 13 insertions(+)Documentation/devicetree/bindings/watchdog/gpio-wdt.txt +3
-0@@ -17,6 +17,9 @@ Optional Properties: - always-running: If the watchdog timer cannot be disabled, add this flag to have the driver keep toggling the signal without a client. It will only cease to toggle the signal when the device is open and the timeout elapsed. +- keep-armed-on-close: if the watchdog timer need to keep toggling the signal + when close, until the timeout elapsed, add this flag to have the driver + keep toggling the signal, until the timeout elapsed. - timeout-sec: Contains the watchdog timeout in seconds. - start-at-init: Start kicking watchdog as soon as driver is loaded.drivers/watchdog/gpio_wdt.c +10
-0@@ -29,6 +29,7 @@ struct gpio_wdt_priv {bool active_low;bool state;bool always_running; +bool keep_armed_on_close;unsigned int hw_algo;struct watchdog_device wdd; };@@ -78,6 +79,13 @@ static int gpio_wdt_stop(struct watchdog_device *wdd) {struct gpio_wdt_priv *priv =watchdog_get_drvdata (wdd); +if (priv->keep_armed_on_close) { +/* Keep the driver running on close. */ +set_bit (WDOG_HW_RUNNING , &wdd->status); + +return 0 ; + } +if (!priv->always_running) {gpio_wdt_disable (priv);clear_bit (WDOG_HW_RUNNING , &wdd->status);@@ -148,6 +156,8 @@ static int gpio_wdt_probe(struct platform_device *pdev) priv->always_running =of_property_read_bool (pdev->dev.of_node,"always-running" ); + priv->keep_armed_on_close =of_property_read_bool (pdev->dev.of_node, +"keep-armed-on-close" );watchdog_set_drvdata (&priv->wdd, priv);--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 46 lines · Guenter Roeck
Quoted 37 lines · Sylvain Lemieux
Quoted 26 lines · Sylvain Lemieux
Hi,
Quoted 23 lines · Guenter Roeck
Quoted 21 lines · Sylvain Lemieux
From: Sylvain Lemieux <[email protected]>
There is a need to allow a grace period after the watchdog software client has closed. It could be used for syncing the filesystem or allow graceful termination while still providing a hardware reset in case the system has hung.
The "always-running" configuration from device-tree does not provide this since it will automatically keep the hardware watchdog alive as soon as the software client closes (i.e. keep toggling the GPIO line regardless of the state of the soft part of the watchdog).
The "keep-armed-on-close" member in the GPIO watchdog implementation indicates if an expired timeout should cause a reset.
This patch add a new "keep-armed-on-close" device-tree configuration that will keep the watchdog "armed" until the next timeout period after a close. During this period, the hardware watchdog is kept alive. A software watchdog client that wants to provide a grace period before a hard reset can set the timeout before properly closing.
Quoted 5 lines
Quoted 3 lines
The description doesn't match what the code actually does, at least from an infrastructure perspective. The infrastructure would just keep it running.
I will need to send a new version with an updated description;
I will submit v3 later today or tomorrow.
Quoted 3 lines
I did not update the description after this patch was rebased on-top of the "watchdog: gpio: keepalives" patch.
Quoted 7 lines
Quoted 5 lines
Quoted 5 lines
What you are really asking for is something the infrastructure should possibly do by itself automatically: To keep pinging a HW watchdog after close until the configured (software) timeout period expires. This would be in line with expectations.
Do you want me to work on a generic version for this option?
Quoted 7 lines
I am not sure I understand the value of the current version (as implemented) in the first place. It seems to be similar to "always-running", with the exception that it doesn't start the watchdog immediately when loading the module. That means it protects the system against hard lockups, but only if the watchdog was opened at least once. That just seems odd, and you'll have to explain the benefit over "always-running", and why it would make sense to have such a selective protection.
The only difference between this implementation and the "always-running" is the way the close operation is handle; when "keep_armed_on_close" option is selected, the watchdog will generate a timeout at the end of the grace period.
Regarding the loading of the module, we have a separate patch, that is apply to the GPIO watchdog to perform an early start (same way as "always-running"); this is not part of this change, as this change only modify the behavior of the driver on close.
Quoted 2 lines
Note that devicetree property changes need to be Acked by DT maintainers.
I will cc them on the new patch.
Quoted 4 lines
Having said that, if what you want is what the description says, not what is implemented, I'll be happy to accept a patch to change the infrastructure accordingly.
I will look into modifying the infrastructure to add the support for "keep_running_on_close"; this will replace this patch.
I will need to submit my other patch for this driver to allow an "early start" of the watchdog
(same as what the "always-running" is doing).
Regards,
Sylvain
Quoted 88 lines
Thanks,
GuenterQuoted 84 lines
Sylvain
Quoted 1 line
[...]
Quoted 73 lines
Sylvain
Quoted 69 lines
Guenter
Quoted 65 lines
Signed-off-by Sylvain Lemieux <[email protected]>---
* This patch depend on the:"watchdog: gpio: Convert to use infrastructure triggered keepalives"; ref. https://lkml.org/lkml/2016/2/28/239 (version 8)Changes from v1 to v2:
* Rebased on-top of the "watchdog: gpio: keepalives" patch.
- Updated the management of the "WDOG_HW_RUNNING" flag.
* Tested with v4.11-rc1.Documentation/devicetree/bindings/watchdog/gpio-wdt.txt | 3 +++ drivers/watchdog/gpio_wdt.c | 10 ++++++++++ 2 files changed, 13 insertions(+)Documentation/devicetree/bindings/watchdog/gpio-wdt.txt +3
-0@@ -17,6 +17,9 @@ Optional Properties: - always-running: If the watchdog timer cannot be disabled, add this flag to have the driver keep toggling the signal without a client. It will only cease to toggle the signal when the device is open and the timeout elapsed. +- keep-armed-on-close: if the watchdog timer need to keep toggling the signal + when close, until the timeout elapsed, add this flag to have the driver + keep toggling the signal, until the timeout elapsed. - timeout-sec: Contains the watchdog timeout in seconds. - start-at-init: Start kicking watchdog as soon as driver is loaded.drivers/watchdog/gpio_wdt.c +10
-0@@ -29,6 +29,7 @@ struct gpio_wdt_priv {bool active_low;bool state;bool always_running; +bool keep_armed_on_close;unsigned int hw_algo;struct watchdog_device wdd; };@@ -78,6 +79,13 @@ static int gpio_wdt_stop(struct watchdog_device *wdd) {struct gpio_wdt_priv *priv =watchdog_get_drvdata (wdd); +if (priv->keep_armed_on_close) { +/* Keep the driver running on close. */ +set_bit (WDOG_HW_RUNNING , &wdd->status); + +return 0 ; + } +if (!priv->always_running) {gpio_wdt_disable (priv);clear_bit (WDOG_HW_RUNNING , &wdd->status);@@ -148,6 +156,8 @@ static int gpio_wdt_probe(struct platform_device *pdev) priv->always_running =of_property_read_bool (pdev->dev.of_node,"always-running" ); + priv->keep_armed_on_close =of_property_read_bool (pdev->dev.of_node, +"keep-armed-on-close" );watchdog_set_drvdata (&priv->wdd, priv);--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Guenter Roeck
maintainerQuoted 54 lines · Sylvain Lemieux
Quoted 46 lines · Guenter Roeck
Quoted 37 lines · Sylvain Lemieux
Quoted 26 lines · Sylvain Lemieux
Hi,
Quoted 23 lines · Guenter Roeck
Quoted 21 lines · Sylvain Lemieux
From: Sylvain Lemieux <[email protected]>
There is a need to allow a grace period after the watchdog software client has closed. It could be used for syncing the filesystem or allow graceful termination while still providing a hardware reset in case the system has hung.
The "always-running" configuration from device-tree does not provide this since it will automatically keep the hardware watchdog alive as soon as the software client closes (i.e. keep toggling the GPIO line regardless of the state of the soft part of the watchdog).
The "keep-armed-on-close" member in the GPIO watchdog implementation indicates if an expired timeout should cause a reset.
This patch add a new "keep-armed-on-close" device-tree configuration that will keep the watchdog "armed" until the next timeout period after a close. During this period, the hardware watchdog is kept alive. A software watchdog client that wants to provide a grace period before a hard reset can set the timeout before properly closing.
Quoted 5 lines
Quoted 3 lines
The description doesn't match what the code actually does, at least from an infrastructure perspective. The infrastructure would just keep it running.
I will need to send a new version with an updated description;
I will submit v3 later today or tomorrow.
Quoted 3 lines
I did not update the description after this patch was rebased on-top of the "watchdog: gpio: keepalives" patch.
Quoted 7 lines
Quoted 5 lines
Quoted 5 lines
What you are really asking for is something the infrastructure should possibly do by itself automatically: To keep pinging a HW watchdog after close until the configured (software) timeout period expires. This would be in line with expectations.
Do you want me to work on a generic version for this option?
Quoted 7 lines
I am not sure I understand the value of the current version (as implemented) in the first place. It seems to be similar to "always-running", with the exception that it doesn't start the watchdog immediately when loading the module. That means it protects the system against hard lockups, but only if the watchdog was opened at least once. That just seems odd, and you'll have to explain the benefit over "always-running", and why it would make sense to have such a selective protection.
Quoted 5 lines
The only difference between this implementation and the "always-running" is the way the close operation is handle; when "
keep_armed_on_close" option is selected, the watchdog will generate a timeout at the end of the grace period.
Not as currently implemented, though.
Quoted 9 lines
Regarding the loading of the module, we have a separate patch, that is apply to the GPIO watchdog to perform an early start (same way as "always-running"); this is not part of this change, as this change only modify the behavior of the driver on close.
Quoted 2 lines
Note that devicetree property changes need to be Acked by DT maintainers.
I will cc them on the new patch.
There is no need for a devicetree property; this is a bug fix, not a feature (user space can expect a watchdog to expire only after the configured grace period expired).
Quoted 11 lines
Quoted 4 lines
Having said that, if what you want is what the description says, not what is implemented, I'll be happy to accept a patch to change the infrastructure accordingly.
I will look into modifying the infrastructure to add the support for "
keep_running_on_close"; this will replace this patch.I will need to submit my other patch for this driver to allow an "early start" of the watchdog
(same as what the "always-running" is doing).
Confused. If the functionality is already there, what would this patch do ?
Thanks,
Guenter
Quoted 55 lines · Guenter Roeck
Quoted 54 lines · Sylvain Lemieux
Quoted 53 lines · Guenter Roeck
Quoted 37 lines · Sylvain Lemieux
Quoted 26 lines · Sylvain Lemieux
Hi,
Quoted 23 lines · Guenter Roeck
Quoted 21 lines · Sylvain Lemieux
From: Sylvain Lemieux <[email protected]>
There is a need to allow a grace period after the watchdog software client has closed. It could be used for syncing the filesystem or allow graceful termination while still providing a hardware reset in case the system has hung.
The "always-running" configuration from device-tree does not provide this since it will automatically keep the hardware watchdog alive as soon as the software client closes (i.e. keep toggling the GPIO line regardless of the state of the soft part of the watchdog).
The "keep-armed-on-close" member in the GPIO watchdog implementation indicates if an expired timeout should cause a reset.
This patch add a new "keep-armed-on-close" device-tree configuration that will keep the watchdog "armed" until the next timeout period after a close. During this period, the hardware watchdog is kept alive. A software watchdog client that wants to provide a grace period before a hard reset can set the timeout before properly closing.
Quoted 5 lines
Quoted 3 lines
The description doesn't match what the code actually does, at least from an infrastructure perspective. The infrastructure would just keep it running.
I will need to send a new version with an updated description;
I will submit v3 later today or tomorrow.
Quoted 3 lines
I did not update the description after this patch was rebased on-top of the "watchdog: gpio: keepalives" patch.
Quoted 7 lines
Quoted 5 lines
Quoted 5 lines
What you are really asking for is something the infrastructure should possibly do by itself automatically: To keep pinging a HW watchdog after close until the configured (software) timeout period expires. This would be in line with expectations.
Do you want me to work on a generic version for this option?
I am not sure I understand the value of the current version (as implemented) in the first place. It seems to be similar to "always-running", with the exception that it doesn't start the watchdog immediately when loading the module. That means it protects the system against hard lockups, but only if the watchdog was opened at least once. That just seems odd, and you'll have to explain the benefit over "always-running", and why it would make sense to have such a selective protection.
Quoted 8 lines
Quoted 5 lines
The only difference between this implementation and the "always-running" is the way the close operation is handle; when "
keep_armed_on_close" option is selected, the watchdog will generate a timeout at the end of the grace period.Not as currently implemented, though.
I will retest; this was the case before this patch was apply to the GPIO watchdog (https://lkml.org/lkml/2016/2/28/239).
Quoted 5 lines
Quoted 5 lines
Regarding the loading of the module, we have a separate patch, that is apply to the GPIO watchdog to perform an early start (same way as "always-running"); this is not part of this change, as this change only modify the behavior of the driver on close.
Quoted 9 lines
Quoted 4 lines
Quoted 2 lines
Note that devicetree property changes need to be Acked by DT maintainers.
I will cc them on the new patch.
There is no need for a devicetree property; this is a bug fix, not a feature (user space can expect a watchdog to expire only after the configured grace period expired).
As stated earlier, I will retest and get back to you.
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Having said that, if what you want is what the description says, not what is implemented, I'll be happy to accept a patch to change the infrastructure accordingly.
Quoted 9 lines
Quoted 7 lines
I will look into modifying the infrastructure to add the support for "
keep_running_on_close"; this will replace this patch.I will need to submit my other patch for this driver to allow an "early start" of the watchdog
(same as what the "always-running" is doing).Confused. If the functionality is already there, what would this patch do ?
This functionality is there with the "always-running"; I need this behavior on loading, but not the "always-running" behavior on close;
This patch is adding an option to start the watchdog at init (i.e. loading).
Quoted 2 lines
Thanks,
Guenter
Guenter Roeck
maintainerQuoted 94 lines · Sylvain Lemieux
Quoted 55 lines · Guenter Roeck
Quoted 54 lines · Sylvain Lemieux
Quoted 53 lines · Guenter Roeck
Quoted 37 lines · Sylvain Lemieux
Quoted 26 lines · Sylvain Lemieux
Hi,
Quoted 23 lines · Guenter Roeck
Quoted 21 lines · Sylvain Lemieux
From: Sylvain Lemieux <[email protected]>
There is a need to allow a grace period after the watchdog software client has closed. It could be used for syncing the filesystem or allow graceful termination while still providing a hardware reset in case the system has hung.
The "always-running" configuration from device-tree does not provide this since it will automatically keep the hardware watchdog alive as soon as the software client closes (i.e. keep toggling the GPIO line regardless of the state of the soft part of the watchdog).
The "keep-armed-on-close" member in the GPIO watchdog implementation indicates if an expired timeout should cause a reset.
This patch add a new "keep-armed-on-close" device-tree configuration that will keep the watchdog "armed" until the next timeout period after a close. During this period, the hardware watchdog is kept alive. A software watchdog client that wants to provide a grace period before a hard reset can set the timeout before properly closing.
Quoted 5 lines
Quoted 3 lines
The description doesn't match what the code actually does, at least from an infrastructure perspective. The infrastructure would just keep it running.
I will need to send a new version with an updated description;
I will submit v3 later today or tomorrow.
Quoted 3 lines
I did not update the description after this patch was rebased on-top of the "watchdog: gpio: keepalives" patch.
Quoted 7 lines
Quoted 5 lines
Quoted 5 lines
What you are really asking for is something the infrastructure should possibly do by itself automatically: To keep pinging a HW watchdog after close until the configured (software) timeout period expires. This would be in line with expectations.
Do you want me to work on a generic version for this option?
I am not sure I understand the value of the current version (as implemented) in the first place. It seems to be similar to "always-running", with the exception that it doesn't start the watchdog immediately when loading the module. That means it protects the system against hard lockups, but only if the watchdog was opened at least once. That just seems odd, and you'll have to explain the benefit over "always-running", and why it would make sense to have such a selective protection.
Quoted 8 lines
Quoted 5 lines
The only difference between this implementation and the "always-running" is the way the close operation is handle; when "
keep_armed_on_close" option is selected, the watchdog will generate a timeout at the end of the grace period.Not as currently implemented, though.
I will retest; this was the case before this patch was apply to the GPIO watchdog (https://lkml.org/lkml/2016/2/28/239).
Quoted 5 lines
Quoted 5 lines
Regarding the loading of the module, we have a separate patch, that is apply to the GPIO watchdog to perform an early start (same way as "always-running"); this is not part of this change, as this change only modify the behavior of the driver on close.
Quoted 9 lines
Quoted 4 lines
Quoted 2 lines
Note that devicetree property changes need to be Acked by DT maintainers.
I will cc them on the new patch.
There is no need for a devicetree property; this is a bug fix, not a feature (user space can expect a watchdog to expire only after the configured grace period expired).
As stated earlier, I will retest and get back to you.
Quoted 11 lines
Quoted 11 lines
Quoted 4 lines
Having said that, if what you want is what the description says, not what is implemented, I'll be happy to accept a patch to change the infrastructure accordingly.
I will look into modifying the infrastructure to add the support for "
keep_running_on_close"; this will replace this patch.I will need to submit my other patch for this driver to allow an "early start" of the watchdog
(same as what the "always-running" is doing).
Quoted 8 lines
Quoted 2 lines
Confused. If the functionality is already there, what would this patch do ?
This functionality is there with the "always-running"; I need this behavior on loading, but not the "always-running" behavior on close;
This patch is adding an option to start the watchdog at init (i.e. loading).
I may be misssing something, but
static int gpio_wdt_probe(struct platform_device *pdev)
{
...
if (priv->always_running)
gpio_wdt_start_impl(priv);
}combined with CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is as early as you can get.
Guenter
Quoted 106 lines · Guenter Roeck
Quoted 94 lines · Sylvain Lemieux
Quoted 55 lines · Guenter Roeck
Quoted 54 lines · Sylvain Lemieux
Quoted 53 lines · Guenter Roeck
Quoted 37 lines · Sylvain Lemieux
Quoted 26 lines · Sylvain Lemieux
Hi,
Quoted 23 lines · Guenter Roeck
Quoted 21 lines · Sylvain Lemieux
From: Sylvain Lemieux <[email protected]>
There is a need to allow a grace period after the watchdog software client has closed. It could be used for syncing the filesystem or allow graceful termination while still providing a hardware reset in case the system has hung.
The "always-running" configuration from device-tree does not provide this since it will automatically keep the hardware watchdog alive as soon as the software client closes (i.e. keep toggling the GPIO line regardless of the state of the soft part of the watchdog).
The "keep-armed-on-close" member in the GPIO watchdog implementation indicates if an expired timeout should cause a reset.
This patch add a new "keep-armed-on-close" device-tree configuration that will keep the watchdog "armed" until the next timeout period after a close. During this period, the hardware watchdog is kept alive. A software watchdog client that wants to provide a grace period before a hard reset can set the timeout before properly closing.
Quoted 5 lines
Quoted 3 lines
The description doesn't match what the code actually does, at least from an infrastructure perspective. The infrastructure would just keep it running.
I will need to send a new version with an updated description;
I will submit v3 later today or tomorrow.
Quoted 3 lines
I did not update the description after this patch was rebased on-top of the "watchdog: gpio: keepalives" patch.
Quoted 7 lines
Quoted 5 lines
Quoted 5 lines
What you are really asking for is something the infrastructure should possibly do by itself automatically: To keep pinging a HW watchdog after close until the configured (software) timeout period expires. This would be in line with expectations.
Do you want me to work on a generic version for this option?
I am not sure I understand the value of the current version (as implemented) in the first place. It seems to be similar to "always-running", with the exception that it doesn't start the watchdog immediately when loading the module. That means it protects the system against hard lockups, but only if the watchdog was opened at least once. That just seems odd, and you'll have to explain the benefit over "always-running", and why it would make sense to have such a selective protection.
Quoted 8 lines
Quoted 5 lines
The only difference between this implementation and the "always-running" is the way the close operation is handle; when "
keep_armed_on_close" option is selected, the watchdog will generate a timeout at the end of the grace period.Not as currently implemented, though.
I will retest; this was the case before this patch was apply to the GPIO watchdog (https://lkml.org/lkml/2016/2/28/239).
Quoted 5 lines
Quoted 5 lines
Regarding the loading of the module, we have a separate patch, that is apply to the GPIO watchdog to perform an early start (same way as "always-running"); this is not part of this change, as this change only modify the behavior of the driver on close.
Quoted 9 lines
Quoted 4 lines
Quoted 2 lines
Note that devicetree property changes need to be Acked by DT maintainers.
I will cc them on the new patch.
There is no need for a devicetree property; this is a bug fix, not a feature (user space can expect a watchdog to expire only after the configured grace period expired).
As stated earlier, I will retest and get back to you.
Quoted 11 lines
Quoted 11 lines
Quoted 4 lines
Having said that, if what you want is what the description says, not what is implemented, I'll be happy to accept a patch to change the infrastructure accordingly.
I will look into modifying the infrastructure to add the support for "
keep_running_on_close"; this will replace this patch.I will need to submit my other patch for this driver to allow an "early start" of the watchdog
(same as what the "always-running" is doing).Quoted 8 lines
Quoted 2 lines
Confused. If the functionality is already there, what would this patch do ?
This functionality is there with the "always-running"; I need this behavior on loading, but not the "always-running" behavior on close;
This patch is adding an option to start the watchdog at init (i.e. loading).
I may be misssing something, but
Quoted 9 lines
static int
gpio_wdt_probe(struct platform_device *pdev){ ... if (priv->always_running) gpio_wdt_start_impl(priv); }combined with
CONFIG_GPIO_WATCHDOG_ARCH_INITCALLis as early as you can get.
I cannot use the "always-running" feature, as this will keep the watchdog always running on close (no timeout).
I need another way to execute the "gpio_wdt_start" during the loading.
Sylvain
Quoted 1 line
Guenter