[2.6.35] AMD-Vi: Enabling IOMMU at 0000:00:00.2 cap 0x40 BUG: unable to handle kernel NULL pointer dereference at 0000000000000198
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hello Joerg,
The requested info is attached.
So that would mean a bios problem ? (those are not on my wishlist :-p)
--
Sander
Quoted 12 lines · you
Quoted 5 lines · Sander Eikelenboom
Hi Joerg,
Trying to boot 2.6.35 with amd iommu enabled on a MSI 890FXA-GD70 motherboard with AMD 890FX chipset results in the oops below, complete serial log attached.
Ok, I have a theory whats going on. It looks like one of your devices aliases to an non-existent pci-bdf. But please send me the data I requested so I can verify this.
Joerg
Signature · 2 lines
Best regards, Sander mailto:[email protected]
[ 0.000000] Itializing cgroupubsys cpuset [ 0.000000] Initlizing cgroup suys cpu [ 0.0000] Linux versin 2.6.352.6.35-villa-xhci-isoc+ oot@serveerstert) (gcc version 4.2 (Debian 4.3.2.1) ) #2 SMP Tue ug 10 16:10:45 CT 2010 [ 0.0000] Command lin: root=/dev/mapp/serveerstertje-ot ro console=tt console=ttyS0,1200n8 amd_iommu_mp [ 0.00000 BIOS-provided pysical RAM map:[ 0.000000] BS-e820: 00000000000000 - 0000000009ac00 (usable)[ 0.000000] OS-e820: 0000000009ac00 - 000000000a000 0 (reserv) [ 0.000000 BIOS-e820: 0000000000e4000 - 00000000100000 (rerved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000c7e90000 (usable) [ 0.000000] BIOS-e820: 00000000c7e90000 - 00000000c7e9e000 (ACPI data) [ 0.000000] BIOS-e820: 00000000c7e9e000 - 00000000c7ee0000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000c7ee0000 - 00000000c7f00000 (reserved) [ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000238000000 (usable) [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI present. [ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it. [ 0.000000] No AGP bridge found [ 0.000000] last_pfn = 0x238000 max_arch_pfn = 0x400000000 [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] last_pfn = 0xc7e90 max_arch_pfn = 0x400000000 [ 0.000000] found SMP MP-table at [ffff8800000ff780] ff780 [ 0.000000] Using GB pages for direct mapping [ 0.000000] init_memory_mapping: 0000000000000000-00000000c7e90000 [ 0.000000] init_memory_mapping: 0000000100000000-0000000238000000 [ 0.000000] RAMDISK: 34974000 - 37ff0000 [ 0.000000] ACPI: RSDP 00000000000fb120 00014 (v00 ACPIAM) [ 0.000000] ACPI: RSDT 00000000c7e90000 00048 (v01 MSI OEMSLIC 20100622 MSFT 00000097) [ 0.000000] ACPI: FACP 00000000c7e90200 00084 (v01 7640MS A7640100 20100622 MSFT 00000097) [ 0.000000] ACPI: DSDT 00000000c7e905e0 09449 (v01 A7640 A7640100 00000100 INTL 20051117) [ 0.000000] ACPI: FACS 00000000c7e9e000 00040 [ 0.000000] ACPI: APIC 00000000c7e90390 00088 (v01 7640MS A7640100 20100622 MSFT 00000097) [ 0.000000] ACPI: MCFG 00000000c7e90420 0003C (v01 7640MS OEMMCFG 20100622 MSFT 00000097) [ 0.000000] ACPI: SLIC 00000000c7e90460 00176 (v01 MSI OEMSLIC 20100622 MSFT 00000097) [ 0.000000] ACPI: OEMB 00000000c7e9e040 00072 (v01 7640MS A7640100 20100622 MSFT 00000097) [ 0.000000] ACPI: SRAT 00000000c7e9a5e0 00108 (v03 AMD FAM_F_10 00000002 AMD 00000001) [ 0.000000] ACPI: HPET 00000000c7e9a6f0 00038 (v01 7640MS OEMHPET 20100622 MSFT 00000097) [ 0.000000] ACPI: IVRS 00000000c7e9a730 00100 (v01 AMD RD890S 00202031 AMD 00000000) [ 0.000000] ACPI: SSDT 00000000c7e9a830 00DA4 (v01 A M I POWERNOW 00000001 AMD 00000001) [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal 0x00100000 -> 0x00238000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[3] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009a [ 0.000000] 0: 0x00000100 -> 0x000c7e90 [ 0.000000] 0: 0x00100000 -> 0x00238000 [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled) [ 0.000000] ACPI: IOAPIC (id[0x06] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 6, version 33, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: IOAPIC (id[0x07] address[0xfec20000] gsi_base[24]) [ 0.000000] IOAPIC[1]: apic_id 7, version 33, address 0xfec20000, GSI 24-55 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8300 base: 0xfed00000 [ 0.000000] SMP: Allowing 6 CPUs, 0 hotplug CPUs [ 0.000000] Allocating PCI resources starting at c7f00000 (gap: c7f00000:37f00000) [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:6 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff880001a00000 s86144 r8192 d24448 u262144 [ 0.000000] pcpu-alloc: s86144 r8192 d24448 u262144 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 - - [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2064858 [ 0.000000] Kernel command line: root=/dev/mapper/serveerstertje-root ro console=tty0 console=ttyS0,115200n8 amd_iomm u_dump [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Node 0: aperture @ 20000000 size 32 MB [ 0.000000] Aperture pointing to e820 RAM. Ignoring. [ 0.000000] Your BIOS doesn't leave a aperture memory hole [ 0.000000] Please enable the IOMMU option in the BIOS setup [ 0.000000] This costs you 64 MB of RAM [ 0.000000] Mapping aperture over 65536 KB of RAM @ 20000000 [ 0.000000] Subtract (56 early reservations) [ 0.000000] #1 [0001000000 - 00018bd464] TEXT DATA BSS [ 0.000000] #2 [0034974000 - 0037ff0000] RAMDISK [ 0.000000] #3 [00018be000 - 00018be10b] BRK [ 0.000000] #4 [00000ff790 - 0000100000] BIOS reserved [ 0.000000] #5 [00000ff780 - 00000ff790] MP-table mpf [ 0.000000] #6 [000009ac00 - 00000fd6a0] BIOS reserved [ 0.000000] #7 [00000fd924 - 00000ff780] BIOS reserved [ 0.000000] #8 [00000fd6a0 - 00000fd924] MP-table mpc [ 0.000000] #9 [0000010000 - 0000012000] TRAMPOLINE [ 0.000000] #10 [0000012000 - 0000014000] PGTABLE [ 0.000000] #11 [0000014000 - 0000015000] PGTABLE [ 0.000000] #12 [00018be140 - 00018bf140] BOOTMEM [ 0.000000] #13 [00018bd480 - 00018bd880] BOOTMEM [ 0.000000] #14 [00020c0000 - 00020c1000] BOOTMEM [ 0.000000] #15 [00020c1000 - 00020c2000] BOOTMEM [ 0.000000] #16 [0002200000 - 0009400000] MEMMAP 0 [ 0.000000] #17 [00018bd880 - 00018bda00] BOOTMEM [ 0.000000] #18 [00018bf140 - 00018d7140] BOOTMEM [ 0.000000] #19 [00018d7140 - 00018ef140] BOOTMEM [ 0.000000] #20 [00018f0000 - 00018f1000] BOOTMEM [ 0.000000] #21 [00018bda00 - 00018bda41] BOOTMEM [ 0.000000] #22 [00018bda80 - 00018bdb06] BOOTMEM [ 0.000000] #23 [00018bdb40 - 00018bdd70] BOOTMEM [ 0.000000] #24 [00018bdd80 - 00018bdde8] BOOTMEM [ 0.000000] #25 [00018bde00 - 00018bde68] BOOTMEM [ 0.000000] #26 [00018bde80 - 00018bdee8] BOOTMEM [ 0.000000] #27 [00018bdf00 - 00018bdf68] BOOTMEM [ 0.000000] #28 [00018bdf80 - 00018bdfe8] BOOTMEM [ 0.000000] #29 [00018ef140 - 00018ef1a8] BOOTMEM [ 0.000000] #30 [00018ef1c0 - 00018ef228] BOOTMEM [ 0.000000] #31 [00018ef240 - 00018ef2a8] BOOTMEM [ 0.000000] #32 [00018ef2c0 - 00018ef328] BOOTMEM [ 0.000000] #33 [00018ef340 - 00018ef39b] BOOTMEM [ 0.000000] #34 [00018ef3c0 - 00018ef41b] BOOTMEM [ 0.000000] #35 [0001a00000 - 0001a1d000] BOOTMEM [ 0.000000] #36 [0001a40000 - 0001a5d000] BOOTMEM [ 0.000000] #37 [0001a80000 - 0001a9d000] BOOTMEM [ 0.000000] #38 [0001ac0000 - 0001add000] BOOTMEM [ 0.000000] #39 [0001b00000 - 0001b1d000] BOOTMEM [ 0.000000] #40 [0001b40000 - 0001b5d000] BOOTMEM [ 0.000000] #41 [00018ef440 - 00018ef448] BOOTMEM [ 0.000000] #42 [00018ef480 - 00018ef488] BOOTMEM [ 0.000000] #43 [00018ef4c0 - 00018ef4d8] BOOTMEM [ 0.000000] #44 [00018ef500 - 00018ef530] BOOTMEM [ 0.000000] #45 [00018ef540 - 00018ef660] BOOTMEM [ 0.000000] #46 [00018ef680 - 00018ef6c8] BOOTMEM [ 0.000000] #47 [00018ef700 - 00018ef748] BOOTMEM [ 0.000000] #48 [00018f1000 - 00018f9000] BOOTMEM [ 0.000000] #49 [0009400000 - 0009c00000] BOOTMEM [ 0.000000] #50 [0001b5d000 - 0001f5d000] BOOTMEM [ 0.000000] #51 [0020000000 - 0024000000] BOOTMEM [ 0.000000] #52 [0009c00000 - 000dc00000] BOOTMEM [ 0.000000] #53 [00018f9000 - 0001919000] BOOTMEM [ 0.000000] #54 [0001919000 - 0001959000] BOOTMEM [ 0.000000] #55 [0000015800 - 000001d800] BOOTMEM [ 0.000000] Memory: 8060444k/9306112k available (4456k kernel code, 919448k absent, 326220k reserved, 2863k data, 512 k init) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU-based detection of stalled CPUs is disabled. [ 0.000000] Verbose stalled-CPUs detection is disabled. [ 0.000000] NR_IRQS:1280 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [ttyS0] enabled [ 0.000000] Fast TSC calibration using PIT [ 0.000000] Detected 3599.817 MHz processor. [ 0.012004] Calibrating delay loop (skipped), value calculated using timer frequency.. 6399.66 BogoMIPS (lpj=12799332 ) [ 0.020002] pid_max: default: 32768 minimum: 301 [ 0.024023] Security Framework initialized [ 0.028003] SELinux: Disabled at boot. [ 0.032009] Mount-cache hash table entries: 256 [ 0.036063] Initializing cgroup subsys ns [ 0.040002] Initializing cgroup subsys cpuacct [ 0.044002] Initializing cgroup subsys devices [ 0.048020] CPU: Physical Processor ID: 0 [ 0.052001] CPU: Processor Core ID: 0 [ 0.056001] mce: CPU supports 6 MCE banks [ 0.060005] using C1E aware idle routine [ 0.064001] Performance Events: AMD PMU driver. [ 0.068002] ... version: 0 [ 0.072001] ... bit width: 48 [ 0.076001] ... generic registers: 4 [ 0.080001] ... value mask: 0000ffffffffffff [ 0.084001] ... max period: 00007fffffffffff [ 0.088001] ... fixed-purpose events: 0 [ 0.092001] ... event mask: 000000000000000f [ 0.096439] ACPI: Core revision 20100428 [ 0.110148] Setting APIC routing to flat [ 0.112261] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.156330] CPU0: AMD Phenom(tm) II X6 1090T Processor stepping 00 [ 0.164000] Booting Node 0, Processors #1 [ 0.256010] System has AMD C1E enabled [ 0.256048] #2 [ 0.256010] Switch to broadcast mode on CPU1 [ 0.348010] Switch to broadcast mode on CPU2 [ 0.348046] #3 [ 0.440026] Switch to broadcast mode on CPU3 [ 0.440068] #4 [ 0.532027] Switch to broadcast mode on CPU4 [ 0.532068] #5 Ok. [ 0.624031] Switch to broadcast mode on CPU5 [ 0.624041] Brought up 6 CPUs [ 0.624043] Total of 6 processors activated (38401.16 BogoMIPS). [ 0.628046] Switch to broadcast mode on CPU0 [ 0.632438] regulator: core version 0.5 [ 0.636120] NET: Registered protocol family 16 [ 0.644189] TOM: 00000000c8000000 aka 3200M [ 0.648009] TOM2: 0000000238000000 aka 9088M [ 0.652061] ACPI: bus type pci registered [ 0.656126] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000) [ 0.660001] PCI: not using MMCONFIG [ 0.664001] PCI: Using configuration type 1 for base access [ 0.668000] PCI: Using configuration type 1 for extended access [ 0.673835] bio: create slab <bio-0> at 0 [ 0.680839] ACPI Error (dswload-0677): [PCI0] Namespace lookup failure, AE_NOT_FOUND [ 0.688001] ACPI Exception: AE_NOT_FOUND, During name lookup/catalog (20100428/psloop-231) [ 0.696001] ACPI Error (psparse-0537): Method parse/execution failed [\] (Node ffffffff818a23d0), AE_NOT_FOUND [ 0.705300] ACPI: Executed 3 blocks of module-level executable AML code [ 0.720687] ACPI: Interpreter enabled [ 0.724001] ACPI: (supports S0 S5) [ 0.727118] ACPI: Using IOAPIC for interrupt routing [ 0.728034] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000) [ 0.732885] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources [ 0.757317] ACPI Warning: Incorrect checksum in table [OEMB] - 0x8E, should be 0x8D (20100428/tbutils-314) [ 0.766070] ACPI: No dock devices found. [ 0.768001] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.772096] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.776243] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] [ 0.780001] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] [ 0.784001] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] [ 0.788001] pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff] [ 0.792001] pci_root PNP0A03:00: host bridge window [mem 0xc8000000-0xdfffffff] [ 0.796001] pci_root PNP0A03:00: host bridge window [mem 0xf0000000-0xfebfffff] [ 0.800980] pci 0000:00:02.0: PCI bridge to [bus 0d-0d] [ 0.804135] pci 0000:00:05.0: PCI bridge to [bus 0c-0c] [ 0.808110] pci 0000:00:06.0: PCI bridge to [bus 0b-0b] [ 0.812106] pci 0000:00:0a.0: PCI bridge to [bus 09-0a] [ 0.816376] pci 0000:09:00.0: PCI bridge to [bus 0a-0a] [ 0.820100] pci 0000:00:0b.0: PCI bridge to [bus 05-08] [ 0.824169] pci 0000:05:00.0: PCI bridge to [bus 06-08] [ 0.828142] pci 0000:06:01.0: PCI bridge to [bus 08-08] [ 0.832132] pci 0000:06:02.0: PCI bridge to [bus 07-07] [ 0.836114] pci 0000:00:0d.0: PCI bridge to [bus 04-04] [ 0.840119] pci 0000:00:14.4: PCI bridge to [bus 03-03] (subtractive decode) [ 0.848067] pci 0000:00:15.0: PCI bridge to [bus 02-02] [ 0.860550] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 7 10 *11 14 15) [ 0.865920] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 7 *10 11 14 15) [ 0.873738] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 *7 10 11 14 15) [ 0.880669] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 7 *10 11 14 15) [ 0.885914] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 7 *10 11 14 15) [ 0.889895] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 7 10 *11 14 15) [ 0.896634] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 7 *10 11 14 15) [ 0.901888] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 7 10 11 14 15) *0 [ 0.906156] vgaarb: device added: PCI:0000:0d:00.0,decodes=io+mem,owns=io+mem,locks=none [ 0.908004] vgaarb: loaded [ 0.912165] SCSI subsystem initialized [ 0.916190] usbcore: registered new interface driver usbfs [ 0.920074] usbcore: registered new interface driver hub [ 0.924085] usbcore: registered new device driver usb [ 0.928160] PCI: Using ACPI for IRQ routing [ 0.932284] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.936916] hpet0: 3 comparators, 32-bit 14.318180 MHz counter [ 0.941800] Switching to clocksource tsc [ 0.944908] pnp: PnP ACPI init [ 0.947648] ACPI: bus type pnp registered [ 0.954240] pnp: PnP ACPI: found 14 devices [ 0.958641] ACPI: ACPI bus type pnp unregistered [ 0.963286] system 00:01: [mem 0xfec20000-0xfec200ff] could not be reserved [ 0.970269] system 00:02: [mem 0xf6000000-0xf6003fff] has been reserved [ 0.976905] system 00:08: [io 0x0600-0x06df] has been reserved [ 0.982848] system 00:08: [io 0x0ae0-0x0aef] has been reserved [ 0.988791] system 00:0a: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.995778] system 00:0a: [mem 0xfee00000-0xfee00fff] has been reserved [ 1.002416] system 00:0b: [io 0x04d0-0x04d1] has been reserved [ 1.008358] system 00:0b: [io 0x040b] has been reserved [ 1.013693] system 00:0b: [io 0x04d6] has been reserved [ 1.019029] system 00:0b: [io 0x0c00-0x0c01] has been reserved [ 1.024971] system 00:0b: [io 0x0c14] has been reserved [ 1.030303] system 00:0b: [io 0x0c50-0x0c51] has been reserved [ 1.036245] system 00:0b: [io 0x0c52] has been reserved [ 1.041581] system 00:0b: [io 0x0c6c] has been reserved [ 1.046914] system 00:0b: [io 0x0c6f] has been reserved [ 1.052249] system 00:0b: [io 0x0cd0-0x0cd1] has been reserved [ 1.058191] system 00:0b: [io 0x0cd2-0x0cd3] has been reserved [ 1.064132] system 00:0b: [io 0x0cd4-0x0cd5] has been reserved [ 1.070074] system 00:0b: [io 0x0cd6-0x0cd7] has been reserved [ 1.076015] system 00:0b: [io 0x0cd8-0x0cdf] has been reserved [ 1.081956] system 00:0b: [io 0x0800-0x089f] has been reserved [ 1.087896] system 00:0b: [io 0x0b00-0x0b1f] has been reserved [ 1.093839] system 00:0b: [io 0x0b20-0x0b3f] has been reserved [ 1.099779] system 00:0b: [io 0x0900-0x090f] has been reserved [ 1.105720] system 00:0b: [io 0x0910-0x091f] has been reserved [ 1.111662] system 00:0b: [io 0xfe00-0xfefe] has been reserved [ 1.117605] system 00:0b: [mem 0xffb80000-0xffbfffff] has been reserved [ 1.124238] system 00:0b: [mem 0xfec10000-0xfec1001f] has been reserved [ 1.130874] system 00:0b: [mem 0xfed80000-0xfed80fff] has been reserved [ 1.137509] system 00:0c: [mem 0xe0000000-0xefffffff] has been reserved [ 1.144143] system 00:0d: [mem 0x00000000-0x0009ffff] could not be reserved [ 1.151125] system 00:0d: [mem 0x000c0000-0x000cffff] has been reserved [ 1.157758] system 00:0d: [mem 0x000e0000-0x000fffff] could not be reserved [ 1.164754] system 00:0d: [mem 0x00100000-0xc7ffffff] could not be reserved [ 1.171739] system 00:0d: [mem 0xfec00000-0xffffffff] could not be reserved [ 1.183293] pci 0000:00:02.0: PCI bridge to [bus 0d-0d] [ 1.188866] pci 0000:00:02.0: bridge window [io 0xe000-0xefff] [ 1.194982] pci 0000:00:02.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 1.201793] pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.209557] pci 0000:00:05.0: PCI bridge to [bus 0c-0c] [ 1.214806] pci 0000:00:05.0: bridge window [io 0xd000-0xdfff] [ 1.220921] pci 0000:00:05.0: bridge window [mem 0xfe800000-0xfe8fffff] [ 1.227728] pci 0000:00:05.0: bridge window [mem 0xcff00000-0xcfffffff 64bit pref] [ 1.235494] pci 0000:00:06.0: PCI bridge to [bus 0b-0b] [ 1.240755] pci 0000:00:06.0: bridge window [io 0xc000-0xcfff] [ 1.246870] pci 0000:00:06.0: bridge window [mem 0xfe700000-0xfe7fffff] [ 1.253677] pci 0000:00:06.0: bridge window [mem 0xcfe00000-0xcfefffff 64bit pref] [ 1.261444] pci 0000:09:00.0: PCI bridge to [bus 0a-0a] [ 1.266691] pci 0000:09:00.0: bridge window [io disabled] [ 1.272376] pci 0000:09:00.0: bridge window [mem 0xfe600000-0xfe6fffff] [ 1.279187] pci 0000:09:00.0: bridge window [mem pref disabled] [ 1.285304] pci 0000:00:0a.0: PCI bridge to [bus 09-0a] [ 1.290551] pci 0000:00:0a.0: bridge window [io disabled] [ 1.296234] pci 0000:00:0a.0: bridge window [mem 0xfe600000-0xfe6fffff] [ 1.303042] pci 0000:00:0a.0: bridge window [mem pref disabled] [ 1.309156] pci 0000:06:01.0: PCI bridge to [bus 08-08] [ 1.314402] pci 0000:06:01.0: bridge window [io disabled] [ 1.320087] pci 0000:06:01.0: bridge window [mem 0xfe500000-0xfe5fffff] [ 1.326893] pci 0000:06:01.0: bridge window [mem pref disabled] [ 1.333011] pci 0000:06:02.0: PCI bridge to [bus 07-07] [ 1.338261] pci 0000:06:02.0: bridge window [io 0xa000-0xbfff] [ 1.344377] pci 0000:06:02.0: bridge window [mem 0xfe400000-0xfe4fffff] [ 1.351183] pci 0000:06:02.0: bridge window [mem pref disabled] [ 1.357299] pci 0000:05:00.0: PCI bridge to [bus 06-08] [ 1.362545] pci 0000:05:00.0: bridge window [io 0xa000-0xbfff] [ 1.368662] pci 0000:05:00.0: bridge window [mem 0xfe400000-0xfe5fffff] [ 1.375470] pci 0000:05:00.0: bridge window [mem pref disabled] [ 1.381585] pci 0000:00:0b.0: PCI bridge to [bus 05-08] [ 1.386831] pci 0000:00:0b.0: bridge window [io 0xa000-0xbfff] [ 1.392946] pci 0000:00:0b.0: bridge window [mem 0xfe300000-0xfe5fffff] [ 1.399753] pci 0000:00:0b.0: bridge window [mem pref disabled] [ 1.405870] pci 0000:00:0d.0: PCI bridge to [bus 04-04] [ 1.411116] pci 0000:00:0d.0: bridge window [io disabled] [ 1.416807] pci 0000:00:0d.0: bridge window [mem 0xfe200000-0xfe2fffff] [ 1.423614] pci 0000:00:0d.0: bridge window [mem pref disabled] [ 1.429731] pci 0000:00:14.4: PCI bridge to [bus 03-03] [ 1.434977] pci 0000:00:14.4: bridge window [io 0x9000-0x9fff] [ 1.441092] pci 0000:00:14.4: bridge window [mem disabled] [ 1.446774] pci 0000:00:14.4: bridge window [mem pref disabled] [ 1.452889] pci 0000:00:15.0: PCI bridge to [bus 02-02] [ 1.458137] pci 0000:00:15.0: bridge window [io disabled] [ 1.463817] pci 0000:00:15.0: bridge window [mem disabled] [ 1.469497] pci 0000:00:15.0: bridge window [mem pref disabled] [ 1.475619] pci 0000:00:02.0: PCI INT A -> GSI 52 (level, low) -> IRQ 52 [ 1.482346] pci 0000:00:05.0: PCI INT A -> GSI 52 (level, low) -> IRQ 52 [ 1.489073] pci 0000:00:06.0: PCI INT A -> GSI 53 (level, low) -> IRQ 53 [ 1.495801] pci 0000:00:0a.0: PCI INT A -> GSI 54 (level, low) -> IRQ 54 [ 1.502535] pci 0000:00:0b.0: PCI INT A -> GSI 54 (level, low) -> IRQ 54 [ 1.509263] pci 0000:05:00.0: PCI INT A -> GSI 32 (level, low) -> IRQ 32 [ 1.515989] pci 0000:06:01.0: PCI INT A -> GSI 33 (level, low) -> IRQ 33 [ 1.522715] pci 0000:06:02.0: PCI INT A -> GSI 34 (level, low) -> IRQ 34 [ 1.529441] pci 0000:00:0d.0: PCI INT A -> GSI 54 (level, low) -> IRQ 54 [ 1.536168] pci 0000:00:15.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.543007] NET: Registered protocol family 2 [ 1.547481] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 1.555296] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 1.566203] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 1.573253] TCP: Hash tables configured (established 262144 bind 65536) [ 1.579919] TCP reno registered [ 1.583084] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 1.589229] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 1.595917] NET: Registered protocol family 1 [ 1.680962] pci 0000:09:00.0: TI XIO2000a quirk detected; secondary bus fast back-to-back transfers disabled [ 1.691019] Trying to unpack rootfs image as initramfs... [ 2.471294] Freeing initrd memory: 55792k freed [ 2.495453] DMA-API: preallocated 32768 debug entries [ 2.500902] DMA-API: debugging enabled by kernel config [ 2.506258] AMD-Vi: device: 00:00.2 cap: 0040 seg: 0 flags: 3e info 1300 [ 2.512993] AMD-Vi: mmio-addr: 00000000f6000000 [ 2.518177] AMD-Vi: DEV_SELECT_RANGE_START devid: 00:00.0 flags: 00 [ 2.524728] AMD-Vi: DEV_RANGE_END devid: 00:00.2 [ 2.529715] AMD-Vi: DEV_SELECT devid: 00:02.0 flags: 00 [ 2.535398] AMD-Vi: DEV_SELECT_RANGE_START devid: 0d:00.0 flags: 00 [ 2.541946] AMD-Vi: DEV_RANGE_END devid: 0d:00.1 [ 2.546934] AMD-Vi: DEV_SELECT devid: 00:05.0 flags: 00 [ 2.552614] AMD-Vi: DEV_SELECT devid: 0c:00.0 flags: 00 [ 2.558296] AMD-Vi: DEV_SELECT devid: 00:06.0 flags: 00 [ 2.563978] AMD-Vi: DEV_SELECT devid: 0b:00.0 flags: 00 [ 2.569659] AMD-Vi: DEV_SELECT devid: 00:0a.0 flags: 00 [ 2.575338] AMD-Vi: DEV_SELECT devid: 09:00.0 flags: 00 [ 2.581022] AMD-Vi: DEV_ALIAS_RANGE devid: 0a:01.0 flags: 00 devid_to: 0a:00.0 [ 2.588611] AMD-Vi: DEV_RANGE_END devid: 0a:1f.7 [ 2.593602] AMD-Vi: DEV_SELECT devid: 00:0b.0 flags: 00 [ 2.599282] AMD-Vi: DEV_SELECT devid: 05:00.0 flags: 00 [ 2.604964] AMD-Vi: DEV_SELECT devid: 06:01.0 flags: 00 [ 2.610644] AMD-Vi: DEV_SELECT devid: 08:00.0 flags: 00 [ 2.616327] AMD-Vi: DEV_SELECT devid: 06:02.0 flags: 00 [ 2.622007] AMD-Vi: DEV_SELECT_RANGE_START devid: 07:00.0 flags: 00 [ 2.628556] AMD-Vi: DEV_RANGE_END devid: 07:00.0 [ 2.633543] AMD-Vi: DEV_SELECT devid: 00:0d.0 flags: 00 [ 2.639224] AMD-Vi: DEV_SELECT devid: 04:00.0 flags: 00 [ 2.644916] AMD-Vi: DEV_SELECT devid: 00:11.0 flags: 00 [ 2.650596] AMD-Vi: DEV_SELECT_RANGE_START devid: 00:12.0 flags: 00 [ 2.657145] AMD-Vi: DEV_RANGE_END devid: 00:12.2 [ 2.662133] AMD-Vi: DEV_SELECT_RANGE_START devid: 00:13.0 flags: 00 [ 2.668680] AMD-Vi: DEV_RANGE_END devid: 00:13.2 [ 2.673668] AMD-Vi: DEV_SELECT devid: 00:14.0 flags: d7 [ 2.679350] AMD-Vi: DEV_SELECT devid: 00:14.3 flags: 00 [ 2.685030] AMD-Vi: DEV_SELECT devid: 00:14.4 flags: 00 [ 2.690714] AMD-Vi: DEV_ALIAS_RANGE devid: 03:00.0 flags: 00 devid_to: 00:14.4 [ 2.698302] AMD-Vi: DEV_RANGE_END devid: 03:1f.7 [ 2.703292] AMD-Vi: DEV_SELECT devid: 00:14.5 flags: 00 [ 2.708973] AMD-Vi: DEV_SELECT devid: 00:15.0 flags: 00 [ 2.714656] AMD-Vi: DEV_SELECT devid: 00:15.1 flags: 00 [ 2.720336] AMD-Vi: DEV_SELECT devid: 01:00.0 flags: 00 [ 2.726017] AMD-Vi: DEV_SELECT_RANGE_START devid: 00:16.0 flags: 00 [ 2.732565] AMD-Vi: DEV_RANGE_END devid: 00:16.2 [ 2.737562] pci 0000:00:00.2: PCI INT A -> GSI 55 (level, low) -> IRQ 55 [ 2.744588] AMD-Vi: Enabling IOMMU at 0000:00:00.2 cap 0x40 [ 2.758364] BUG: unable to handle kernel NULL pointer dereference at 0000000000000118 [ 2.760899] IP: [<ffffffff810274c2>] domain_for_device+0x21/0x7b [ 2.760899] PGD 0 [ 2.760899] Oops: 0000 [#1] SMP [ 2.760899] last sysfs file: [ 2.760899] CPU 0 [ 2.760899] Modules linked in: [ 2.760899] [ 2.760899] Pid: 1, comm: swapper Not tainted 2.6.352.6.35-vanilla-xhci-isoc+ #2 890FXA-GD70 (MS-7640) /MS-7640 [ 2.760899] RIP: 0010:[<ffffffff810274c2>] [<ffffffff810274c2>] domain_for_device+0x21/0x7b [ 2.760899] RSP: 0018:ffff880237c7fe20 EFLAGS: 00010282 [ 2.760899] RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffff812548b8 [ 2.760899] RDX: 0000000000000a08 RSI: 0000000000000037 RDI: ffff88023743c888 [ 2.760899] RBP: ffff880237c7fe50 R08: ffff880237442000 R09: ffff880237dceef0 [ 2.760899] R10: 3000001a00000000 R11: ffffffff810acaec R12: ffffffff816c7da0 [ 2.760899] R13: ffff880237fef380 R14: 0000000000000900 R15: ffff88023743c888 [ 2.760899] FS: 0000000000000000(0000) GS:ffff880001a00000(0000) knlGS:0000000000000000 [ 2.760899] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 2.760899] CR2: 0000000000000118 CR3: 00000000016ba000 CR4: 00000000000006f0 [ 2.760899] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 2.760899] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [ 2.760899] Process swapper (pid: 1, threadinfo ffff880237c7e000, task ffff880237c7d3c0) [ 2.760899] Stack: [ 2.760899] ffffffff816c7da0 ffffffff81798c68 ffffffff816c7da0 ffff88022a82e800 [ 2.760899] <0> 0000000000000900 ffff88023743c800 ffff880237c7fea0 ffffffff81751dd7 [ 2.760899] <0> ffff880237c7fea0 ffff88022a82e810 ffff88023743c888 ffffffff81798c68 [ 2.760899] Call Trace: [ 2.760899] [<ffffffff81751dd7>] amd_iommu_init_dma_ops+0x137/0x371 [ 2.760899] [<ffffffff81750d6e>] amd_iommu_init+0x288/0x466 [ 2.760899] [<ffffffff81745813>] ? pci_iommu_init+0x0/0x47 [ 2.760899] [<ffffffff81745833>] pci_iommu_init+0x20/0x47 [ 2.760899] [<ffffffff81002060>] do_one_initcall+0x5a/0x155 [ 2.760899] [<ffffffff8173e70b>] kernel_init+0x176/0x1ff [ 2.760899] [<ffffffff81009364>] kernel_thread_helper+0x4/0x10 [ 2.760899] [<ffffffff8173e595>] ? kernel_init+0x0/0x1ff [ 2.760899] [<ffffffff81009360>] ? kernel_thread_helper+0x0/0x10 [ 2.760899] Code: 41 5c 41 5d 41 5e 41 5f c9 c3 55 48 89 e5 41 57 49 89 ff 41 56 41 55 41 54 53 31 db 48 83 ec 08 4c 8b af 18 01 00 00 49 8b 45 18 <4c> 8b a0 18 01 00 00 4d 85 e4 74 3e 48 c7 c7 c0 7e 6c 81 e8 11 [ 2.760899] RIP [<ffffffff810274c2>] domain_for_device+0x21/0x7b [ 2.760899] RSP <ffff880237c7fe20> [ 2.760899] CR2: 0000000000000118 [ 3.005043] ---[ end trace 6d450e935ee1897c ]--- [ 3.009690] Kernel panic - not syncing: Attempted to kill init! [ 3.015630] Pid: 1, comm: swapper Tainted: G D 2.6.352.6.35-vanilla-xhci-isoc+ #2 [ 3.023914] Call Trace: [ 3.026390] [<ffffffff8145524f>] panic+0xb1/0x12a [ 3.031204] [<ffffffff8108831f>] ? call_rcu_sched+0x10/0x12 [ 3.036893] [<ffffffff8108832a>] ? call_rcu+0x9/0xb [ 3.041897] [<ffffffff81043f2e>] ? put_files_struct+0xb5/0xc2 [ 3.047751] [<ffffffff8104bfec>] ? exit_ptrace+0x33/0x131 [ 3.053262] [<ffffffff81045567>] do_exit+0x78/0x6fa [ 3.058249] [<ffffffff81042fe9>] ? kmsg_dump+0x126/0x140 [ 3.063670] [<ffffffff8100c30c>] oops_end+0x91/0x96 [ 3.068659] [<ffffffff8102a786>] no_context+0x1f3/0x202 [ 3.073994] [<ffffffff810ac1b7>] ? get_page_from_freelist+0x410/0x4d3 [ 3.080542] [<ffffffff8102a955>] __bad_area_nosemaphore+0x1c0/0x1e6 [ 3.086916] [<ffffffff8102a989>] bad_area_nosemaphore+0xe/0x10 [ 3.092857] [<ffffffff8102ac82>] do_page_fault+0x16d/0x31a [ 3.098454] [<ffffffff81457bb5>] page_fault+0x25/0x30 [ 3.103614] [<ffffffff810acaec>] ? get_zeroed_page+0x11/0x15 [ 3.109382] [<ffffffff812548b8>] ? match_pci_dev_by_id+0x0/0x5c [ 3.115410] [<ffffffff810274c2>] ? domain_for_device+0x21/0x7b [ 3.121352] [<ffffffff81751dd7>] amd_iommu_init_dma_ops+0x137/0x371 [ 3.127726] [<ffffffff81750d6e>] amd_iommu_init+0x288/0x466 [ 3.133408] [<ffffffff81745813>] ? pci_iommu_init+0x0/0x47 [ 3.139002] [<ffffffff81745833>] pci_iommu_init+0x20/0x47 [ 3.144511] [<ffffffff81002060>] do_one_initcall+0x5a/0x155 [ 3.150190] [<ffffffff8173e70b>] kernel_init+0x176/0x1ff [ 3.155613] [<ffffffff81009364>] kernel_thread_helper+0x4/0x10 [ 3.161555] [<ffffffff8173e595>] ? kernel_init+0x0/0x1ff [ 3.166975] [<ffffffff81009360>] ? kernel_thread_helper+0x0/0x10
00:00.0 Host bridge [0600]: ATI Technologies Inc RD890 Northbridge only single slot PCI-e GFX Hydra part [1002:5a11] (rev 02)
Subsystem: ATI Technologies Inc RD890 Northbridge only single slot PCI-e GFX Hydra part [1002:5a11]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Capabilities: [f0] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [c4] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=20 MastHost- DefDir- DUL-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- Revision ID: 3.00
Link Frequency 0: [b]
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [40] HyperTransport: Retry Mode
Capabilities: [54] HyperTransport: UnitID Clumping
Capabilities: [9c] HyperTransport: #1a
Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/2 Enable-
Address: 00000000 Data: 0000
00:00.2 Generic system peripheral [0806]: ATI Technologies Inc Device [1002:5a23]
Subsystem: ATI Technologies Inc Device [1002:5a23]
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Capabilities: [40] Secure device <?>
Capabilities: [54] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [64] HyperTransport: MSI Mapping Enable+ Fixed+
00:02.0 PCI bridge [0604]: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port B) [1002:5a16] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0d, subordinate=0d, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fe900000-fe9fffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <1us, L1 <8us
ClockPM- Suprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 1, PowerLimit 91.000000; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee3f00c Data: 4171
Capabilities: [b0] Subsystem: ATI Technologies Inc Device [1002:5a11]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100] Vendor Specific Information <?>
Capabilities: [190] Access Controls <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:05.0 PCI bridge [0604]: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port E) [1002:5a19] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe800000-fe8fffff
Prefetchable memory behind bridge: 00000000cff00000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <8us
ClockPM- Suprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 5, PowerLimit 75.000000; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee3f00c Data: 4179
Capabilities: [b0] Subsystem: ATI Technologies Inc Device [1002:5a11]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100] Vendor Specific Information <?>
Capabilities: [190] Access Controls <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:06.0 PCI bridge [0604]: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port F) [1002:5a1a] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fe700000-fe7fffff
Prefetchable memory behind bridge: 00000000cfe00000-00000000cfefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <8us
ClockPM- Suprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 6, PowerLimit 75.000000; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee3f00c Data: 4181
Capabilities: [b0] Subsystem: ATI Technologies Inc Device [1002:5a11]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100] Vendor Specific Information <?>
Capabilities: [190] Access Controls <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:0a.0 PCI bridge [0604]: ATI Technologies Inc RD890 PCI to PCI bridge (external gfx1 port A) [1002:5a1d] (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=09, subordinate=0a, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fe600000-fe6fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <8us
ClockPM- Suprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 2, PowerLimit 75.000000; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee3f00c Data: 4189
Capabilities: [b0] Subsystem: ATI Technologies Inc Device [1002:5a11]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100] Vendor Specific Information <?>
Capabilities: [190] Access Controls <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:0b.0 PCI bridge [0604]: ATI Technologies Inc RD890 PCI to PCI bridge (NB-SB link) [1002:5a1f] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=08, sec-latency=0
I/O behind bridge: 0000a000-0000bfff
Memory behind bridge: fe300000-fe5fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <1us, L1 <8us
ClockPM- Suprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 5, PowerLimit 31.000000; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee3f00c Data: 4191
Capabilities: [b0] Subsystem: ATI Technologies Inc Device [1002:5a11]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100] Vendor Specific Information <?>
Capabilities: [190] Access Controls <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:0d.0 PCI bridge [0604]: ATI Technologies Inc RD890 PCI to PCI bridge (external gfx1 port B) [1002:5a1e] (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fe200000-fe2fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0 <1us, L1 <8us
ClockPM- Suprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 4, PowerLimit 75.000000; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee3f00c Data: 4199
Capabilities: [b0] Subsystem: ATI Technologies Inc Device [1002:5a11]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100] Vendor Specific Information <?>
Capabilities: [190] Access Controls <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:11.0 SATA controller [0106]: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] [1002:4391] (rev 40) (prog-if 01 [AHCI 1.0])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7640] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 82 Region 0: I/O ports at 6000 [size=8] Region 1: I/O ports at 5000 [size=4] Region 2: I/O ports at 3000 [size=8] Region 3: I/O ports at 2000 [size=4] Region 4: I/O ports at 1000 [size=16] Region 5: Memory at fe0ff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable+ Address: 00000000fee3f00c Data: 41c9 Capabilities: [70] SATA HBA <?> Capabilities: [a4] PCIe advanced features <?> Kernel driver in use: ahci
00:12.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7640]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe0fb000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:12.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7640]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe0ff400 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7640]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe0fc000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7640]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe0ff800 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 41)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Kernel modules: i2c-piix4
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d] (rev 40)
Subsystem: Micro-Star International Co., Ltd. Device [1462:7640]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384] (rev 40) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 00009000-00009fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:14.5 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller [1002:4399] (prog-if 10 [OHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7640]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe0fd000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:15.0 PCI bridge [0604]: ATI Technologies Inc Device [1002:43a0] (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #247, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 20, PowerLimit 75.000000; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee3f00c Data: 41a1
Capabilities: [b0] Subsystem: ATI Technologies Inc Device [1002:0000]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100] Vendor Specific Information <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:16.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7640]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe0fe000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:16.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: Micro-Star International Co., Ltd. Device [1462:7640]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe0ffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] HyperTransport Configuration [1022:1200]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Revision ID: 3.00
Link Frequency: [b]
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Address Map [1022:1201]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] DRAM Controller [1022:1202]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Kernel modules: amd64_edac_mod
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Miscellaneous Control [1022:1203]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>
00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Link Control [1022:1204]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
03:06.0 Multimedia audio controller [0401]: C-Media Electronics Inc CM8738 [13f6:0111] (rev 10)
Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device [13f6:0111]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 9800 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: C-Media PCI
Kernel modules: snd-cmipci
04:00.0 USB Controller [0c03]: NEC Corporation Device [1033:0194] (rev 03) (prog-if 30)
Subsystem: Micro-Star International Co., Ltd. Device [1462:4257]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 40
Region 0: Memory at fe2fe000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [90] MSI-X: Enable+ Mask- TabSize=8
Vector table: BAR=0 offset=00001000
PBA: BAR=0 offset=00001080
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 unlimited
ClockPM+ Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
Capabilities: [150] #18
Kernel driver in use: xhci_hcd
05:00.0 PCI bridge [0604]: PLX Technology, Inc. Device [10b5:8613] (rev ba) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Region 0: Memory at fe3e0000 (32-bit, non-prefetchable) [size=128K]
Bus: primary=05, secondary=06, subordinate=08, sec-latency=0
I/O behind bridge: 0000a000-0000bfff
Memory behind bridge: fe400000-fe5fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/2 Enable+
Address: 00000000fee3f00c Data: 41a9
Masking: 00000001 Pending: 00000000
Capabilities: [68] Express (v2) Upstream Port, MSI 00
DevCap: MaxPayload 2048 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-SlotPowerLimit 31.000000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0 <1us, L1 <2us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [a4] Subsystem: PLX Technology, Inc. Device [10b5:8613]
Capabilities: [100] Device Serial Number 00-0e-df-b5-10-01-86-ba
Capabilities: [fb4] Advanced Error Reporting <?>
Capabilities: [138] Power Budgeting <?>
Capabilities: [148] Virtual Channel <?>
Capabilities: [448] Vendor Specific Information <?>
Capabilities: [950] Vendor Specific Information <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
06:01.0 PCI bridge [0604]: PLX Technology, Inc. Device [10b5:8613] (rev ba) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=06, secondary=08, subordinate=08, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fe500000-fe5fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/2 Enable+
Address: 00000000fee3f00c Data: 41b1
Masking: 00000001 Pending: 00000000
Capabilities: [68] Express (v2) Downstream Port (Slot+), MSI 00
DevCap: MaxPayload 2048 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0 <1us, L1 <2us
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk- DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 71, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
Capabilities: [a4] Subsystem: PLX Technology, Inc. Device [10b5:8613]
Capabilities: [100] Device Serial Number 00-0e-df-b5-10-01-86-ba
Capabilities: [fb4] Advanced Error Reporting <?>
Capabilities: [148] Virtual Channel <?>
Capabilities: [520] Access Controls <?>
Capabilities: [950] Vendor Specific Information <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
06:02.0 PCI bridge [0604]: PLX Technology, Inc. Device [10b5:8613] (rev ba) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=06, secondary=07, subordinate=07, sec-latency=0
I/O behind bridge: 0000a000-0000bfff
Memory behind bridge: fe400000-fe4fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/2 Enable+
Address: 00000000fee3f00c Data: 41b9
Masking: 00000001 Pending: 00000000
Capabilities: [68] Express (v2) Downstream Port (Slot+), MSI 00
DevCap: MaxPayload 2048 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0 <1us, L1 <2us
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk- DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 72, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
Capabilities: [a4] Subsystem: PLX Technology, Inc. Device [10b5:8613]
Capabilities: [100] Device Serial Number 00-0e-df-b5-10-01-86-ba
Capabilities: [fb4] Advanced Error Reporting <?>
Capabilities: [148] Virtual Channel <?>
Capabilities: [520] Access Controls <?>
Capabilities: [950] Vendor Specific Information <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
07:00.0 SATA controller [0106]: Device [1b4b:9123] (rev 10) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:8400]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 83
Region 0: I/O ports at b800 [size=8]
Region 1: I/O ports at b400 [size=4]
Region 2: I/O ports at b000 [size=8]
Region 3: I/O ports at a800 [size=4]
Region 4: I/O ports at a400 [size=16]
Region 5: Memory at fe4ff800 (32-bit, non-prefetchable) [size=2K]
Expansion ROM at fe4e0000 [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee3f00c Data: 41d1
Capabilities: [70] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Kernel driver in use: ahci
08:00.0 USB Controller [0c03]: NEC Corporation Device [1033:0194] (rev 03) (prog-if 30)
Subsystem: ASUSTeK Computer Inc. Device [1043:8413]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 33
Region 0: Memory at fe5fe000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [90] MSI-X: Enable+ Mask- TabSize=8
Vector table: BAR=0 offset=00001000
PBA: BAR=0 offset=00001080
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 unlimited
ClockPM+ Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
Capabilities: [150] #18
Kernel driver in use: xhci_hcd
09:00.0 PCI bridge [0604]: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge [104c:8231] (rev 03) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=09, secondary=0a, subordinate=0a, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fe600000-fe6fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/4 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Gammagraphx, Inc. Device [0000:0000]
Capabilities: [90] Express (v1) PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <16us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Kernel modules: shpchp
0a:01.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 44
Region 0: Memory at fe6fd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
0a:01.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 45
Region 0: Memory at fe6fe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
0a:01.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 04) (prog-if 20 [EHCI])
Subsystem: Device [1838:1074]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (4000ns min, 8500ns max), Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 46
Region 0: Memory at fe6ffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ehci_hcd
0b:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 03)
Subsystem: Micro-Star International Co., Ltd. Device [1462:7640]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 99
Region 0: I/O ports at c800 [size=256]
Region 2: Memory at cfeff000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at cfef8000 (64-bit, prefetchable) [size=16K]
Expansion ROM at fe7e0000 [disabled] [size=128K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee3f00c Data: 41ca
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM+ Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [ac] MSI-X: Enable- Mask- TabSize=4
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [cc] Vital Product Data <?>
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-e0-4c-68-00-00-00-03
Kernel driver in use: r8169
Kernel modules: r8169
0c:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 03)
Subsystem: Micro-Star International Co., Ltd. Device [1462:7640]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 98
Region 0: I/O ports at d800 [size=256]
Region 2: Memory at cffff000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at cfff8000 (64-bit, prefetchable) [size=16K]
Expansion ROM at fe8e0000 [disabled] [size=128K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee3f00c Data: 41ba
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM+ Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [ac] MSI-X: Enable- Mask- TabSize=4
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [cc] Vital Product Data <?>
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-e0-4c-68-00-00-00-04
Kernel driver in use: r8169
Kernel modules: r8169
0d:00.0 VGA compatible controller [0300]: ATI Technologies Inc Mobility Radeon HD 3450 [1002:95c5] (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:01d4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at fe9e0000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at e000 [size=256]
Expansion ROM at fe9c0000 [disabled] [size=128K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [100] Vendor Specific Information <?>
0d:00.1 Audio device [0403]: ATI Technologies Inc RV620 Audio device [Radeon HD 34xx Series] [1002:aa28]
Subsystem: ASUSTeK Computer Inc. Device [1043:aa28]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 100
Region 0: Memory at fe9fc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee3f00c Data: 41e2
Capabilities: [100] Vendor Specific Information <?>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
Quoted 2 lines · Sander Eikelenboom
The requested info is attached.
So that would mean a bios problem ? (those are not on my wishlist :-p)
Yeah, looks like a BIOS problem. But the driver should handle that without crashing the system, so there is a bug in the driver too.
Problem is:
AMD-Vi: DEV_ALIAS_RANGE devid: 0a:01.0 flags: 00 devid_to: 0a:00.0 AMD-Vi: DEV_RANGE_END devid: 0a:1f.7
This means that PCI devices from 0a:01.0 to 0a:1f.7 may use their own device-id or 0a:00.0. But a device which id 0a:00.0 is not present in the system. From the lspci output this looks like your USB3 controler should alias to 09:00.0. I prepare a patch for you to fix the crash but I can't guarantee that your USB3 controler will work afterwards. If you see IO-Page-Faults please report them to me.
Joerg
Hello Joerg,
Could you also provide a perhaps more specific message what is wrong with the bios, that i could forward to MSI, in the hope it will reach the bios engineers someday ? :-)
--
Sander
Quoted 20 lines · you
Quoted 2 lines · Sander Eikelenboom
The requested info is attached.
So that would mean a bios problem ? (those are not on my wishlist :-p)Yeah, looks like a BIOS problem. But the driver should handle that without crashing the system, so there is a bug in the driver too.
Problem is:
AMD-Vi: DEV_ALIAS_RANGE devid: 0a:01.0 flags: 00 devid_to: 0a:00.0 AMD-Vi: DEV_RANGE_END devid: 0a:1f.7This means that PCI devices from 0a:01.0 to 0a:1f.7 may use their own device-id or 0a:00.0. But a device which id 0a:00.0 is not present in the system. From the lspci output this looks like your USB3 controler should alias to 09:00.0. I prepare a patch for you to fix the crash but I can't guarantee that your USB3 controler will work afterwards. If you see IO-Page-Faults please report them to me.
Joerg
Signature · 2 lines
Best regards, Sander mailto:[email protected]
Quoted 3 lines · Sander Eikelenboom
Could you also provide a perhaps more specific message what is wrong with the bios, that i could forward to MSI, in the hope it will reach the bios engineers someday ? :-)
Lets first prove that my theory is right before contacting MSI directly. Can you try the attached patch? it should fix the boot-crash. When the system booted successfully please try some USB device (make sure it uses the seperate usb-controler, I guess the seperate device is responsible for USB 3, so try to plug a device into one of your USB 3 ports). If you finished that please send me whether it worked or not and the full dmesg output of the system.
Joerg
arch/x86/kernel/amd_iommu.c +2 -0
@@ -153,6 +153,8 @@ static int iommu_init_device(struct device *dev) pdev =pci_get_bus_and_slot (PCI_BUS (alias), alias &0xff );if (pdev) dev_data->alias = &pdev->dev; +else + dev_data->alias = dev;atomic_set (&dev_data->bind,0 );
Hello Joerg,
Errr which seperate usb controller ? .. it has actually:
- 1 pci-e usb 2.0 controller
- 2 pci-e usb 3.0 controller (one of which includes a sata controller as well)
(apart from the onboard stuff)
--
Sander
Quoted 14 lines · you
Quoted 3 lines · Sander Eikelenboom
Could you also provide a perhaps more specific message what is wrong with the bios, that i could forward to MSI, in the hope it will reach the bios engineers someday ? :-)
Lets first prove that my theory is right before contacting MSI directly. Can you try the attached patch? it should fix the boot-crash. When the system booted successfully please try some USB device (make sure it uses the seperate usb-controler, I guess the seperate device is responsible for USB 3, so try to plug a device into one of your USB 3 ports). If you finished that please send me whether it worked or not and the full dmesg output of the system.
Joerg
Signature · 2 lines
Best regards, Sander mailto:[email protected]
Hi Sander,
Quoted 3 lines · Sander Eikelenboom
Errr which seperate usb controller ? .. it has actually:
- 1 pci-e usb 2.0 controller
- 2 pci-e usb 3.0 controller (one of which includes a sata controller as well)
The devices should be attached to this controler:
0a:01.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI]) 0a:01.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI]) 0a:01.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 04) (prog-if 20 [EHCI])
The PCI devices associated with that controler alias to 0a:00.0 which does not exist in your system (hence the crash). And the fact that these devices have an alias makes me believe that the BIOS detects them as legacy PCI devices. PCI-e does typically not has aliases. Can you send lcpi -t output to see to which upstream bridge these devices are connected to?
Joerg
Hmmm the fun part seems to be .. that the usb devices on that usb2 controller seemed to work fine on Xen.
And i have some problems about xen not willing to passthrough things with the usb3 controllers (supposedly due to the (extra) bridges), that are the controllers on 04:00.0 and 08:00.0
-[0000:00]-+-00.0
+-00.2
+-02.0-[0000:0d]--+-00.0
| \-00.1
+-05.0-[0000:0c]----00.0
+-06.0-[0000:0b]----00.0
+-0a.0-[0000:09-0a]----00.0-[0000:0a]--+-01.0
| +-01.1
| \-01.2
+-0b.0-[0000:05-08]----00.0-[0000:06-08]--+-01.0-[0000:08]----00.0
| \-02.0-[0000:07]----00.0
+-0d.0-[0000:04]----00.0
+-11.0
+-12.0
+-12.2
+-13.0
+-13.2
+-14.0
+-14.3
+-14.4-[0000:03]----06.0
+-14.5
+-15.0-[0000:02]--
+-16.0
+-16.2
+-18.0
+-18.1
+-18.2
+-18.3
\-18.4I had hoped things would become easier/better with my new mobo including iommu :-)
Doesn't seem that way yet. Previously i had 2 usb2.0 controllers(1x pci 1x pci-e) and 1 usb3.0(pci-e) passed through (with xen-swiotlb and no hardware iommu).. and that worked fine grabbing video 24/7 for several weeks.
But lets hope for the best :-)
--
Sander
Quoted 21 lines · you
Hi Sander,
Quoted 3 lines · Sander Eikelenboom
Errr which seperate usb controller ? .. it has actually:
- 1 pci-e usb 2.0 controller
- 2 pci-e usb 3.0 controller (one of which includes a sata controller as well)The devices should be attached to this controler:
0a:01.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI]) 0a:01.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI]) 0a:01.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 04) (prog-if 20 [EHCI])
The PCI devices associated with that controler alias to 0a:00.0 which does not exist in your system (hence the crash). And the fact that these devices have an alias makes me believe that the BIOS detects them as legacy PCI devices. PCI-e does typically not has aliases. Can you send lcpi -t output to see to which upstream bridge these devices are connected to?
Joerg
Signature · 2 lines
Best regards, Sander mailto:[email protected]
Quoted 2 lines · Sander Eikelenboom
Hmmm the fun part seems to be .. that the usb devices on that usb2 controller seemed to work fine on Xen.
Hmm, thats weird. In this case these devices probably do not alias at all. But lets wait for the results when you test my patch.
Quoted 3 lines
+-0a.0-[0000:09-0a]----00.0-[0000:0a]--+-01.0
| +-01.1
| \-01.2Yeah, device 09:00.0 is a PCIe-to-PCI bridge and the addtional USB controlers are behind that bridge as legacy PCI devices. Thats why the BIOS sets up the alias-entry. It should set up 09:00.0 instead of 0a:00.0 to make things work correctly.
Joerg
Hi Joerg,
Ok it boots ok now, but plugging in a USB device in the 2.0 controller (0a.01.*) results in a flood of error messages about the usb controller not functioning.
When running same kernel with amd_iommu=off results in ...the device at least registering properly as usb device (altough trying to use it now resulted in an entirely new oops probably in the driver of the videograbber.)
--
Sander
Quoted 18 lines · you
Quoted 2 lines · Sander Eikelenboom
Hmmm the fun part seems to be .. that the usb devices on that usb2 controller seemed to work fine on Xen.
Hmm, thats weird. In this case these devices probably do not alias at all. But lets wait for the results when you test my patch.
Quoted 3 lines
+-0a.0-[0000:09-0a]----00.0-[0000:0a]--+-01.0 | +-01.1 | \-01.2Yeah, device 09:00.0 is a PCIe-to-PCI bridge and the addtional USB controlers are behind that bridge as legacy PCI devices. Thats why the BIOS sets up the alias-entry. It should set up 09:00.0 instead of 0a:00.0 to make things work correctly.
Joerg
Signature · 2 lines
Best regards, Sander mailto:[email protected]
It boots now, dmesg attached.
Quoted 21 lines · you
Hi Sander,
Quoted 3 lines · Sander Eikelenboom
Errr which seperate usb controller ? .. it has actually:
- 1 pci-e usb 2.0 controller
- 2 pci-e usb 3.0 controller (one of which includes a sata controller as well)The devices should be attached to this controler:
0a:01.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI]) 0a:01.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI]) 0a:01.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 04) (prog-if 20 [EHCI])
The PCI devices associated with that controler alias to 0a:00.0 which does not exist in your system (hence the crash). And the fact that these devices have an alias makes me believe that the BIOS detects them as legacy PCI devices. PCI-e does typically not has aliases. Can you send lcpi -t output to see to which upstream bridge these devices are connected to?
Joerg
Signature · 2 lines
Best regards, Sander mailto:[email protected]
Ok,
Quoted 1 line · Sander Eikelenboom
It boots now, dmesg attached.
AMD-Vi: Event logged [IO_PAGE_FAULT device=0a:00.0 domain=0x0000 address=0x0000000000001080 flags=0x0070]
So it indeed uses 0a:00.0 as the device id. Thats weird but states that the BIOS is actually ok. I need to fix that in the driver.
Thanks,
Joerg
Quoted 1 line · Sander Eikelenboom
It boots now, dmesg attached.
Ok, here is a quick and dirty patch wich should make your system boot again. It introduces other issues which will show up when you try to assign the devices to a virtual machine. But at least the devices should work again on bare-metal.
Joerg
arch/x86/include/asm/amd_iommu_types.h +5 -0
@@ -285,6 +285,8 @@ struct protection_domain { }; +#define INVALID_ALIAS_ID (~0U) +/* * This struct contains device specific data for the IOMMU */
@@ -294,6 +296,9 @@ struct iommu_dev_data {struct device *alias;/* The Alias Device */ struct protection_domain *domain;/* Domain the device is bound to */ atomic_t bind;/* Domain attach reverent count */ + +u32 alias_id;/* Use in case device aliases to +non-existend PCI BDF */ };/*
arch/x86/kernel/amd_iommu.c +12 -0
@@ -148,11 +148,17 @@ static int iommu_init_device(struct device *dev) dev_data->dev = dev; + dev_data->alias_id =INVALID_ALIAS_ID ; + devid =get_device_id (dev); alias = amd_iommu_alias_table[devid]; pdev =pci_get_bus_and_slot (PCI_BUS (alias), alias &0xff );if (pdev) dev_data->alias = &pdev->dev; +else { + dev_data->alias = dev; + dev_data->alias_id = alias; + }atomic_set (&dev_data->bind,0 );
@@ -1448,6 +1454,9 @@ static void do_attach(struct device *dev, struct protection_domain *domain)list_add (&dev_data->list, &domain->dev_list);set_dte_entry (devid, domain); +if (dev_data->alias_id !=INVALID_ALIAS_ID ) +set_dte_enry (dev_data->alias_id, domain); +/* Do reference counting */ domain->dev_iommu[iommu->index] +=1 ; domain->dev_cnt +=1 ;
@@ -1475,6 +1484,9 @@ static void do_detach(struct device *dev)list_del (&dev_data->list);clear_dte_entry (devid); +if (dev_data->alias_id !=INVALID_ALIAS_ID ) +clear_dte_enry (dev_data->alias_id); +/* Flush the DTE entry */ iommu_flush_device (dev); }
Hello Joerg,
Had to apply the patch by hand, and found 2 typo's:
arch/x86/kernel/amd_iommu.c: In function âdo_attachâ:arch/x86/kernel/amd_iommu.c:1456: error: implicit declaration of function âset_dte_enryâ arch/x86/kernel/amd_iommu.c: In function âdo_detachâ:arch/x86/kernel/amd_iommu.c:1486: error: implicit declaration of function âclear_dte_enryâ make[2]: *** [arch/x86/kernel/amd_iommu.o] Error 1
Should be "entry" of course.
--
Sander
Quoted 9 lines · you
Quoted 1 line · Sander Eikelenboom
It boots now, dmesg attached.
Ok, here is a quick and dirty patch wich should make your system boot again. It introduces other issues which will show up when you try to assign the devices to a virtual machine. But at least the devices should work again on bare-metal.
Joerg
Signature · 2 lines
Best regards, Sander mailto:[email protected]