hwmon: (pmbus): Add POWER System power supply driver

new file mode 100644
index 0000000..2ea8ea2
@@ -0,0 +1,21 @@
+Device-tree bindings for IBM POWER system power supplies
+--------------------------------------------------------
+
+Required properties:
+ - compatible = "ibm,power-ps";
+ - reg = < I2C bus address >;		: Address of the power supply on the
+					  I2C bus.
+
+Example:
+
+    i2c-bus@100 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        #interrupt-cells = <1>;
+        < more properties >
+
+        power_ps@68 {
+            compatible = "ibm,power-ps";
+            reg = <0x68>;
+        };
+    };

index 04f6baa..7074f8d 100644
@@ -135,6 +135,16 @@ config SENSORS_MAX8688
 	  This driver can also be built as a module. If so, the module will
 	  be called max8688.
 
+config SENSORS_POWERPS
+	tristate "IBM POWER System Power Supply"
+	default n
+	help
+	  If you say yes here you get hardware monitoring support for the IBM
+	  POWER system power supply.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called powerps.
+
 config SENSORS_TPS40422
 	tristate "TI TPS40422"
 	default n

index 663801c..009aefa 100644
@@ -14,6 +14,7 @@ obj-$(CONFIG_SENSORS_MAX20751)	+= max20751.o
 obj-$(CONFIG_SENSORS_MAX31785)	+= max31785.o
 obj-$(CONFIG_SENSORS_MAX34440)	+= max34440.o
 obj-$(CONFIG_SENSORS_MAX8688)	+= max8688.o
+obj-$(CONFIG_SENSORS_POWERPS)	+= powerps.o
 obj-$(CONFIG_SENSORS_TPS40422)	+= tps40422.o
 obj-$(CONFIG_SENSORS_UCD9000)	+= ucd9000.o
 obj-$(CONFIG_SENSORS_UCD9200)	+= ucd9200.o

new file mode 100644
index 0000000..a4fbe92
@@ -0,0 +1,54 @@
+Kernel driver powerps
+=====================
+
+Supported chips:
+  * POWER system power supply
+
+Author: Eddie James <[email protected]>
+
+Description
+-----------
+
+This driver supports POWER system power supplies. This driver is a client
+to the core PMBus driver.
+
+Usage Notes
+-----------
+
+This driver should auto-detect devices. In the event that it does not, you will
+have to instantiate the devices explicitly. Please see
+Documentation/i2c/instantiating-devices for details.
+
+Sysfs entries
+-------------
+
+The following attributes are supported:
+
+curr1_alarm		Output current over-current fault.
+curr1_input		Measured output current in mA.
+curr1_label		"iout1"
+
+fan1_alarm		Fan 1 warning.
+fan1_fault		Fan 1 fault.
+fan1_input		Fan 1 speed in RPM.
+fan2_alarm		Fan 2 warning.
+fan2_fault		Fan 2 fault.
+fan2_input		Fan 2 speed in RPM.
+
+in1_alarm		Input voltage under-voltage fault.
+in1_input		Measured input voltage in mV.
+in1_label		"vin"
+in2_alarm		Output voltage over-voltage fault.
+in2_input		Measured output voltage in mV.
+in2_label		"vout1"
+
+power1_alarm		Input fault.
+power1_input		Measured input power in uW.
+power1_label		"pin"
+
+temp1_alarm		PSU inlet ambient temperature over-temperature fault.
+temp1_input		Measured PSU inlet ambient temp in millidegrees C.
+temp2_alarm		Secondary rectifier temp over-temperature fault.
+temp2_input		Measured secondary rectifier temp in millidegrees C.
+temp3_alarm		ORing FET temperature over-temperature fault.
+temp3_input		Measured ORing FET temperature in millidegrees C.

index 9ab8e46..841d9ab 100644
@@ -417,6 +417,16 @@
 			type = <PCA955X_TYPE_GPIO>;
 		};
 	};
+
+	power_ps@68 {
+		compatible = "ibm,power-ps"
+		reg = <0x68>;
+	};
+
+	power_ps@69 {
+		compatible = "ibm,power-ps";
+		reg = <0x69>;
+	};
 };
 
 &i2c4 {