QEMU 2.10.0
Hello,
I've updated openbmc/qemu's master to 2.10.0. For anyone maintaining patches on top of master I've merged the old master state into 2.10.0 with the --ours strategy, then applied the series Cédric is maintaining on top. This means any patches you might have on top of master should rebase easily due to shared history, whilst keeping our yet-to-be- upstreamed patches in an easily identified set.
Cheers,
Andrew
Quoted 8 lines · Andrew Jeffery
Hello,
I've updated openbmc/qemu's master to 2.10.0. For anyone maintaining patches on top of master I've merged the old master state into 2.10.0 with the --ours strategy, then applied the series Cédric is maintaining on top. This means any patches you might have on top of master should rebase easily due to shared history, whilst keeping our yet-to-be- upstreamed patches in an easily identified set.
Here are some updates on the QEMU wiki :
https://github.com/openbmc/qemu/wiki
Thanks,
C.
Quoted 10 lines · Cédric Le Goater
Quoted 8 lines · Andrew Jeffery
Hello,
I've updated openbmc/qemu's master to 2.10.0. For anyone maintaining patches on top of master I've merged the old master state into 2.10.0 with the --ours strategy, then applied the series Cédric is maintaining on top. This means any patches you might have on top of master should rebase easily due to shared history, whilst keeping our yet-to-be- upstreamed patches in an easily identified set.
Quoted 3 lines
Here are some updates on the QEMU wiki :
Thanks Andrew and Cedric.
I built myself openbmc/qemu master and tried to boot a dev-4.10 kernel with a simple busybox based userspace on it. It hangs at "Starting network".
I was previously using Cedric's 'aspeed' branch from a long time ago.
This is my little qemu script that I use. Can you reproduce? Or tell me what I'm doing wrong here?
#!/bin/bash
: ${BMC_CS1:=/srv/tftp/flash-witherspoon}
: ${BMC_CS2:=${BMC_CS1}}
: ${PNOR:=/srv/tftp/witherspoon.pnor}
~/dev/qemu/openbmc/arm-softmmu/qemu-system-arm -m 512 -M witherspoon-bmc \
-nodefaults -nographic -serial stdio \
-net nic -net user,hostname=qemu,hostfwd=::2222-:22,hostfwd=::2623-:623 \
-drive file=${BMC_CS1},format=raw,if=mtd \
-drive file=${BMC_CS2},format=raw,if=mtd \
-drive file=${PNOR},format=raw,if=mtd \
"$@"
Cheers,
Joel
Quoted 38 lines · Joel Stanley
Quoted 10 lines · Cédric Le Goater
Quoted 8 lines · Andrew Jeffery
Hello,
I've updated openbmc/qemu's master to 2.10.0. For anyone maintaining patches on top of master I've merged the old master state into 2.10.0 with the --ours strategy, then applied the series Cédric is maintaining on top. This means any patches you might have on top of master should rebase easily due to shared history, whilst keeping our yet-to-be- upstreamed patches in an easily identified set.
Quoted 3 lines
Here are some updates on the QEMU wiki :
Thanks Andrew and Cedric.
I built myself openbmc/qemu master and tried to boot a dev-4.10 kernel with a simple busybox based userspace on it. It hangs at "Starting network".
I was previously using Cedric's 'aspeed' branch from a long time ago.
This is my little qemu script that I use. Can you reproduce? Or tell me what I'm doing wrong here?
#!/bin/bash
: ${BMC_CS1:=/srv/tftp/flash-witherspoon}
: ${BMC_CS2:=${BMC_CS1}}
: ${PNOR:=/srv/tftp/witherspoon.pnor}~/dev/qemu/openbmc/arm-softmmu/qemu-system-arm -m 512 -M witherspoon-bmc \
(quoted diff) +0
-5-nodefaults -nographic -serial stdio \ -net nic -net user,hostname=qemu,hostfwd=::2222-:22,hostfwd=::2623-:623 \ -drive file=${BMC_CS1},format=raw,if=mtd \ -drive file=${BMC_CS2},format=raw,if=mtd \ -drive file=${PNOR},format=raw,if=mtd \
Quoted 1 line
"$@"
I don't see any problems with the network with :
[ 2.200000] ftgmac100 1e660000.ethernet: Read MAC address c0:ff:ee:00:00:03 from chip [ 2.200000] ftgmac100 1e660000.ethernet: Using NCSI interface [ 2.200000] ftgmac100 1e660000.ethernet eth0: irq 20, mapped at f0060000 [ 2.380000] 8021q: 802.1Q VLAN Support v1.8 [ 26.990000] 8021q: adding VLAN 0 to HW filter on device eth0 [ 27.520000] ftgmac100 1e660000.ethernet eth0: no vlan ids left to set [ 27.520000] ftgmac100 1e660000.ethernet eth0: NCSI interface up
network is up. the QEMU ftgmac100 model does not support VLAN though.
May be it's your image ?
C.
Quoted 53 lines · Cédric Le Goater
Quoted 38 lines · Joel Stanley
Quoted 11 lines
Quoted 1 line · Cédric Le Goater
Quoted 8 lines · Andrew Jeffery
Hello,
I've updated openbmc/qemu's master to 2.10.0. For anyone maintaining patches on top of master I've merged the old master state into 2.10.0 with the --ours strategy, then applied the series Cédric is maintaining on top. This means any patches you might have on top of master should rebase easily due to shared history, whilst keeping our yet-to-be- upstreamed patches in an easily identified set.
Quoted 3 lines
Here are some updates on the QEMU wiki :
Thanks Andrew and Cedric.
I built myself openbmc/qemu master and tried to boot a dev-4.10 kernel with a simple busybox based userspace on it. It hangs at "Starting network".
I was previously using Cedric's 'aspeed' branch from a long time ago.
This is my little qemu script that I use. Can you reproduce? Or tell me what I'm doing wrong here?
#!/bin/bash
: ${BMC_CS1:=/srv/tftp/flash-witherspoon}
: ${BMC_CS2:=${BMC_CS1}}
: ${PNOR:=/srv/tftp/witherspoon.pnor}~/dev/qemu/openbmc/arm-softmmu/qemu-system-arm -m 512 -M witherspoon-bmc \
(quoted diff) +0
-5-nodefaults -nographic -serial stdio \ -net nic -net user,hostname=qemu,hostfwd=::2222-:22,hostfwd=::2623-:623 \ -drive file=${BMC_CS1},format=raw,if=mtd \ -drive file=${BMC_CS2},format=raw,if=mtd \ -drive file=${PNOR},format=raw,if=mtd \Quoted 1 line
"$@"
I don't see any problems with the network with :
[ 2.200000] ftgmac100 1e660000.ethernet: Read MAC address c0:ff:ee:00:00:03 from chip [ 2.200000] ftgmac100 1e660000.ethernet: Using NCSI interface
[ 2.200000] ftgmac100 1e660000.ethernet eth0: irq 20, mapped atf0060000[ 2.380000] 8021q: 802.1Q VLAN Support v1.8
[ 26.990000] 8021q: adding VLAN 0 to HW filter on device eth0
[ 27.520000] ftgmac100 1e660000.ethernet eth0: no vlan ids left to set
[ 27.520000] ftgmac100 1e660000.ethernet eth0: NCSI interface up
Quoted 1 line
network is up. the QEMU ftgmac100 model does not support VLAN though.
I didn't see any issues with networking in my tests either. Maybe we should take this conversation to the openbmc/qemu/issues?
Cheers,
Andrew
Quoted 10 lines · Cédric Le Goater
Quoted 8 lines · Andrew Jeffery
Hello,
I've updated openbmc/qemu's master to 2.10.0. For anyone maintaining patches on top of master I've merged the old master state into 2.10.0 with the --ours strategy, then applied the series Cédric is maintaining on top. This means any patches you might have on top of master should rebase easily due to shared history, whilst keeping our yet-to-be- upstreamed patches in an easily identified set.
Quoted 3 lines
Here are some updates on the QEMU wiki :
Thanks!
Andrew