rsi: add bluetooth and coex support
Subsystems (2)
v3 cover rsi: add bluetooth and coex support
From: Amitkumar Karwar <[email protected]>
This patch series adds new bluetooth driver and coex enhancments in existing wlan driver for RSI chipsets.
As per our architecture, both wlan and bluetooth drivers talk over same SDIO interface to device. Separate endpoint will be used in case of USB interface.
Changes in v3: 5/8 and 6/8 patches are modified Changes in v2: 2/8, 5/8 and 6/8 patches are modified
Prameela Rani Garnepudi (6):
rsi: add rx control block to handle rx packets in USB
rsi: add header file rsi_header
rsi: add coex support
Bluetooth: btrsi: add new rsi bluetooth driver
rsi: add module parameter operating mode
rsi: sdio changes to support BT
Siva Rebbagondla (2):
rsi: add bluetooth rx endpoint
rsi: handle BT traffic in driver
drivers/bluetooth/Kconfig | 11 ++ drivers/bluetooth/Makefile | 2 + drivers/bluetooth/btrsi.c | 211 ++++++++++++++++++++++++++++ drivers/bluetooth/rsi_hci.h | 40 ++++++ drivers/net/wireless/rsi/Kconfig | 2 +- drivers/net/wireless/rsi/Makefile | 1 + drivers/net/wireless/rsi/rsi_91x_coex.c | 184 ++++++++++++++++++++++++ drivers/net/wireless/rsi/rsi_91x_core.c | 16 ++- drivers/net/wireless/rsi/rsi_91x_hal.c | 56 ++++++-- drivers/net/wireless/rsi/rsi_91x_main.c | 110 ++++++++++++++- drivers/net/wireless/rsi/rsi_91x_mgmt.c | 2 +- drivers/net/wireless/rsi/rsi_91x_sdio.c | 13 +- drivers/net/wireless/rsi/rsi_91x_sdio_ops.c | 5 +- drivers/net/wireless/rsi/rsi_91x_usb.c | 124 +++++++++++----- drivers/net/wireless/rsi/rsi_91x_usb_ops.c | 35 +++-- drivers/net/wireless/rsi/rsi_coex.h | 38 +++++ drivers/net/wireless/rsi/rsi_common.h | 5 +- drivers/net/wireless/rsi/rsi_hal.h | 21 +++ drivers/net/wireless/rsi/rsi_main.h | 20 +-- drivers/net/wireless/rsi/rsi_mgmt.h | 3 + drivers/net/wireless/rsi/rsi_usb.h | 16 ++- include/linux/rsi_header.h | 56 ++++++++ 22 files changed, 888 insertions(+), 83 deletions(-) create mode 100644 drivers/bluetooth/btrsi.c create mode 100644 drivers/bluetooth/rsi_hci.h create mode 100644 drivers/net/wireless/rsi/rsi_91x_coex.c create mode 100644 drivers/net/wireless/rsi/rsi_coex.h create mode 100644 include/linux/rsi_header.h
Signature · 1 line
2.7.4
PATCH v3 1/8 rsi: add rx control block to handle rx packets in USB
From: Prameela Rani Garnepudi <[email protected]>
Rx bluetooth endpoint shall be added in further patches. Rx control block is introduced here to handle Rx packets properly. Separate function is written to initialize the RX control blocks.
--- drivers/net/wireless/rsi/rsi_91x_main.c | 4 +- drivers/net/wireless/rsi/rsi_91x_sdio_ops.c | 2 +- drivers/net/wireless/rsi/rsi_91x_usb.c | 75 +++++++++++++++++++++++------ drivers/net/wireless/rsi/rsi_91x_usb_ops.c | 35 +++++++++----- drivers/net/wireless/rsi/rsi_common.h | 2 +- drivers/net/wireless/rsi/rsi_main.h | 2 +- drivers/net/wireless/rsi/rsi_usb.h | 10 +++- 7 files changed, 96 insertions(+), 34 deletions(-)
drivers/net/wireless/rsi/rsi_91x_main.c +2 -2
@@ -137,7 +137,7 @@ static struct sk_buff *rsi_prepare_skb(struct rsi_common *common,* * Return: 0 on success, -1 on failure. */ -int rsi_read_pkt (struct rsi_common *common,s32 rcv_pkt_len) +int rsi_read_pkt (struct rsi_common *common,u8 *rx_pkt,s32 rcv_pkt_len) {u8 *frame_desc =NULL , extended_desc =0 ;u32 index, length =0 , queueno =0 ;
@@ -146,7 +146,7 @@ int rsi_read_pkt(struct rsi_common *common, s32 rcv_pkt_len) index =0 ; do { - frame_desc = &common->rx_data_pkt[index]; + frame_desc = &rx_pkt[index]; actual_length = *(u16 *)&frame_desc[0]; offset = *(u16 *)&frame_desc[2];
drivers/net/wireless/rsi/rsi_91x_sdio_ops.c +1 -1
@@ -118,7 +118,7 @@ static int rsi_process_pkt(struct rsi_common *common) goto fail; } - status =rsi_read_pkt (common, rcv_pkt_len); + status =rsi_read_pkt (common, common->rx_data_pkt, rcv_pkt_len); fail:kfree (common->rx_data_pkt);
drivers/net/wireless/rsi/rsi_91x_usb.c +59 -16
137 lines not on this page · raw message
drivers/net/wireless/rsi/rsi_91x_usb_ops.c +23 -12
@@ -29,7 +29,8 @@ void rsi_usb_rx_thread(struct rsi_common *common) {struct rsi_hw *adapter = common->priv;struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev; -int status; +struct rx_usb_ctrl_block *rx_cb; +int status, idx; do { rsi_wait_event(&dev->rx_thread.event, EVENT_WAIT_FOREVER);
@@ -37,20 +38,30 @@ void rsi_usb_rx_thread(struct rsi_common *common)if (atomic_read (&dev->rx_thread.thread_done)) goto out; -mutex_lock (&common->rx_lock); - status =rsi_read_pkt (common,0 ); -if (status) { -rsi_dbg (ERR_ZONE ,"%s: Failed To read data" , __func__); +for (idx =0 ; idx <MAX_RX_URBS ; idx++) { + rx_cb = &dev->rx_cb[idx]; +if (!rx_cb->pend) +continue ; + +mutex_lock (&common->rx_lock); + status =rsi_read_pkt (common, rx_cb->rx_buffer,0 ); +if (status) { +rsi_dbg (ERR_ZONE ,"%s: Failed To read data" , + __func__); +mutex_unlock (&common->rx_lock); +break ; + } + rx_cb->pend =0 ;mutex_unlock (&common->rx_lock); -return ; + +if (adapter->rx_urb_submit (adapter, rx_cb->ep_num)) { +rsi_dbg (ERR_ZONE , +"%s: Failed in urb submission" , + __func__); +return ; + } } -mutex_unlock (&common->rx_lock);rsi_reset_event (&dev->rx_thread.event); -if (adapter->rx_urb_submit (adapter)) { -rsi_dbg (ERR_ZONE , -"%s: Failed in urb submission" , __func__); -return ; - } }while (1 ); out:
drivers/net/wireless/rsi/rsi_common.h +1 -1
@@ -82,7 +82,7 @@ void rsi_mac80211_detach(struct rsi_hw *hw);u16 rsi_get_connected_channel (struct ieee80211_vif *vif);struct rsi_hw *rsi_91x_init (void );void rsi_91x_deinit (struct rsi_hw *adapter); -int rsi_read_pkt (struct rsi_common *common,s32 rcv_pkt_len); +int rsi_read_pkt (struct rsi_common *common,u8 *rx_pkt,s32 rcv_pkt_len);#ifdef CONFIG_PM int rsi_config_wowlan (struct rsi_hw *adapter,struct cfg80211_wowlan *wowlan);#endif
drivers/net/wireless/rsi/rsi_main.h +1 -1
@@ -343,7 +343,7 @@ struct rsi_hw {void *rsi_dev;struct rsi_host_intf_ops *host_intf_ops;int (*check_hw_queue_status)(struct rsi_hw *adapter,u8 q_num); -int (*rx_urb_submit)(struct rsi_hw *adapter); +int (*rx_urb_submit)(struct rsi_hw *adapter,u8 ep_num);int (*determine_event_timeout)(struct rsi_hw *adapter); };
drivers/net/wireless/rsi/rsi_usb.h +9 -1
@@ -39,12 +39,20 @@#define RSI_USB_BUF_SIZE 4096#define RSI_USB_CTRL_BUF_SIZE 0x04 +struct rx_usb_ctrl_block { +u8 *data; +struct urb *rx_urb; +u8 *rx_buffer; +u8 ep_num; +u8 pend; +}; +struct rsi_91x_usbdev {struct rsi_thread rx_thread;u8 endpoint;struct usb_device *usbdev;struct usb_interface *pfunction; -struct urb *rx_usb_urb[MAX_RX_URBS ]; +struct rx_usb_ctrl_block rx_cb[MAX_RX_URBS ];u8 *tx_buffer;__le16 bulkin_size;u8 bulkin_endpoint_addr;
Signature · 1 line
2.7.4
PATCH v3 2/8 rsi: add bluetooth rx endpoint
In reply to Amitkumar KarwarFrom: Siva Rebbagondla <[email protected]>
USB endpoint 1 is used for WLAN which is presently in use. USB endpoint 2 is introduced for BT Rx traffic. Enumeration of Rx BT endpoint and submitting Rx BT URB are added.
Quoted 1 line
From
/sys/kernel/debug/usb/devices,
Ad=81(I) is for WLAN EP IN and Ad=01(O) is for Wlan EP OUT. Ad=82(I) is for BT EP IN and Ad=02(O) is for BT EP OUT.
T: Bus=01 Lev=01 Prnt=01 Port=09 Cnt=03 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1618 ProdID=9113 Rev= 0.02 S: Manufacturer=Redpine Signals, Inc. S: Product=Wireless USB Network Module S: SerialNumber=000000000001 C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA I:* If#= 0 Alt= 0 #EPs= 6 Cls=00(>ifc ) Sub=00 Prot=00 Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
---
v3: Same as v2
v2: Included '/sys/kernel/debug/usb/devices' info in patch description(Marcel)
--- drivers/net/wireless/rsi/rsi_91x_usb.c | 37 ++++++++++++++++++++-------------- drivers/net/wireless/rsi/rsi_usb.h | 6 +++--- 2 files changed, 25 insertions(+), 18 deletions(-)
drivers/net/wireless/rsi/rsi_91x_usb.c +22 -15
@@ -103,41 +103,42 @@ static int rsi_find_bulk_in_and_out_endpoints(struct usb_interface *interface,struct usb_host_interface *iface_desc;struct usb_endpoint_descriptor *endpoint;__le16 buffer_size; -int ii, bep_found =0 ; +int ii, bin_found =0 , bout_found =0 ; iface_desc = &(interface->altsetting[0 ]);for (ii =0 ; ii < iface_desc->desc.bNumEndpoints; ++ii) { endpoint = &(iface_desc->endpoint[ii].desc); -if ((!(dev->bulkin_endpoint_addr)) && +if (!dev->bulkin_endpoint_addr[bin_found] && (endpoint->bEndpointAddress &USB_DIR_IN ) && - ((endpoint->bmAttributes & -USB_ENDPOINT_XFERTYPE_MASK ) == + ((endpoint->bmAttributes &USB_ENDPOINT_XFERTYPE_MASK ) ==USB_ENDPOINT_XFER_BULK )) { buffer_size = endpoint->wMaxPacketSize; - dev->bulkin_size = buffer_size; - dev->bulkin_endpoint_addr = + dev->bulkin_size[bin_found] = buffer_size; + dev->bulkin_endpoint_addr[bin_found] = endpoint->bEndpointAddress; + bin_found++; } -if (!dev->bulkout_endpoint_addr[bep_found] && +if (!dev->bulkout_endpoint_addr[bout_found] && !(endpoint->bEndpointAddress &USB_DIR_IN ) && ((endpoint->bmAttributes &USB_ENDPOINT_XFERTYPE_MASK ) == -USB_ENDPOINT_XFER_BULK )) { - dev->bulkout_endpoint_addr[bep_found] = +USB_ENDPOINT_XFER_BULK )) { + buffer_size = endpoint->wMaxPacketSize; + dev->bulkout_endpoint_addr[bout_found] = endpoint->bEndpointAddress; buffer_size = endpoint->wMaxPacketSize; - dev->bulkout_size[bep_found] = buffer_size; - bep_found++; + dev->bulkout_size[bout_found] = buffer_size; + bout_found++; } -if (bep_found >=MAX_BULK_EP ) +if (bin_found >=MAX_BULK_EP || bout_found >=MAX_BULK_EP )break ; } -if (!(dev->bulkin_endpoint_addr) && - (dev->bulkout_endpoint_addr[0 ])) +if (!(dev->bulkin_endpoint_addr[0 ]) && + dev->bulkout_endpoint_addr[0 ])return -EINVAL ;return 0 ;
@@ -273,7 +274,7 @@ static int rsi_rx_urb_submit(struct rsi_hw *adapter, u8 ep_num) usb_fill_bulk_urb(urb, dev->usbdev, usb_rcvbulkpipe(dev->usbdev, - dev->bulkin_endpoint_addr), + dev->bulkin_endpoint_addr[ep_num - 1]), urb->transfer_buffer, 3000, rsi_rx_done_handler,
@@ -745,6 +746,12 @@ static int rsi_probe(struct usb_interface *pfunction,if (status) goto err1; +if (adapter->priv->coex_mode >1 ) { + status =rsi_rx_urb_submit (adapter,BT_EP ); +if (status) + goto err1; + } +return 0 ; err1:rsi_deinit_usb_interface (adapter);
drivers/net/wireless/rsi/rsi_usb.h +3 -3
@@ -31,7 +31,7 @@#define USB_VENDOR_REGISTER_WRITE 0x16#define RSI_USB_TX_HEAD_ROOM 128 -#define MAX_RX_URBS 1 +#define MAX_RX_URBS 2#define MAX_BULK_EP 8#define WLAN_EP 1#define BT_EP 2
@@ -54,8 +54,8 @@ struct rsi_91x_usbdev {struct usb_interface *pfunction;struct rx_usb_ctrl_block rx_cb[MAX_RX_URBS ];u8 *tx_buffer; -__le16 bulkin_size; -u8 bulkin_endpoint_addr; +__le16 bulkin_size[MAX_BULK_EP ]; +u8 bulkin_endpoint_addr[MAX_BULK_EP ];__le16 bulkout_size[MAX_BULK_EP ];u8 bulkout_endpoint_addr[MAX_BULK_EP ];u32 tx_blk_size;
Signature · 1 line
2.7.4
PATCH v3 3/8 rsi: add header file rsi_header
In reply to Amitkumar KarwarFrom: Prameela Rani Garnepudi <[email protected]>
The common parameters used by wlan and bt modules are added to a new header file "rsi_header.h" defined in '/include/linux'
--- drivers/net/wireless/rsi/rsi_main.h | 12 ++---------- include/linux/rsi_header.h | 34 ++++++++++++++++++++++++++++++++++ 2 files changed, 36 insertions(+), 10 deletions(-) create mode 100644 include/linux/rsi_header.h
drivers/net/wireless/rsi/rsi_main.h +2 -10
@@ -20,6 +20,7 @@#include <linux/string.h> #include <linux/skbuff.h> #include <net/mac80211.h> +#include <linux/rsi_header.h> struct rsi_sta {struct ieee80211_sta *sta;
@@ -85,10 +86,6 @@ extern __printf(2, 3) void rsi_dbg(u32 zone, const char *fmt, ...);#define MGMT_HW_Q 10#define BEACON_HW_Q 11 -/* Queue information */ -#define RSI_COEX_Q 0x0 -#define RSI_WIFI_MGMT_Q 0x4 -#define RSI_WIFI_DATA_Q 0x5#define IEEE80211_MGMT_FRAME 0x00#define IEEE80211_CTL_FRAME 0x04
@@ -293,11 +290,6 @@ struct rsi_common {struct ieee80211_vif *roc_vif; }; -enum host_intf { -RSI_HOST_INTF_SDIO =0 , -RSI_HOST_INTF_USB -}; -struct eepromrw_info {u32 offset;u32 length;
@@ -322,7 +314,7 @@ struct rsi_hw {struct device *device;u8 sc_nvifs; -enum host_intf rsi_host_intf; +enum rsi_host_intf rsi_host_intf;u16 block_size;enum ps_state ps_state;struct rsi_ps_info ps_info;
include/linux/rsi_header.h new file +34 -0
@@ -0,0 +1,34 @@ +/** +* Copyright (c) 2017 Redpine Signals Inc. +* +* Permission to use, copy, modify, and/or distribute this software for any +* purpose with or without fee is hereby granted, provided that the above +* copyright notice and this permission notice appear in all copies. +* +* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES +* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF +* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR +* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES +* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN +* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF +* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. +*/ + +#ifndef __RSI_HEADER_H__ +#define __RSI_HEADER_H__ + +/* HAL queue information */ +#define RSI_COEX_Q 0x0 +#define RSI_BT_Q 0x2 +#define RSI_WLAN_Q 0x3 +#define RSI_WIFI_MGMT_Q 0x4 +#define RSI_WIFI_DATA_Q 0x5 +#define RSI_BT_MGMT_Q 0x6 +#define RSI_BT_DATA_Q 0x7 + +enum rsi_host_intf { +RSI_HOST_INTF_SDIO =0 , +RSI_HOST_INTF_USB +}; + +#endif
Signature · 1 line
2.7.4
PATCH v3 4/8 rsi: add coex support
In reply to Amitkumar KarwarFrom: Prameela Rani Garnepudi <[email protected]>
With BT support, driver has to handle two streams of data (i.e. wlan and BT). Actual coex implementation is in firmware. Coex module just schedule the packets to firmware by taking them from the corresponding paths.
Structures for module and protocol operations are introduced for this purpose. Protocol operations structure is global structure which can be shared among different modules. Initialization of coex and operating mode values is moved to rsi_91x_init().
--- drivers/net/wireless/rsi/Makefile | 1 + drivers/net/wireless/rsi/rsi_91x_coex.c | 182 ++++++++++++++++++++++++++++++++ drivers/net/wireless/rsi/rsi_91x_hal.c | 17 +-- drivers/net/wireless/rsi/rsi_91x_main.c | 30 +++++- drivers/net/wireless/rsi/rsi_91x_mgmt.c | 2 +- drivers/net/wireless/rsi/rsi_91x_sdio.c | 1 + drivers/net/wireless/rsi/rsi_91x_usb.c | 2 + drivers/net/wireless/rsi/rsi_coex.h | 38 +++++++ drivers/net/wireless/rsi/rsi_main.h | 5 + drivers/net/wireless/rsi/rsi_mgmt.h | 3 + include/linux/rsi_header.h | 20 ++++ 11 files changed, 291 insertions(+), 10 deletions(-) create mode 100644 drivers/net/wireless/rsi/rsi_91x_coex.c create mode 100644 drivers/net/wireless/rsi/rsi_coex.h
drivers/net/wireless/rsi/Makefile +1 -0
@@ -5,6 +5,7 @@ rsi_91x-y += rsi_91x_mac80211.o rsi_91x-y += rsi_91x_mgmt.o rsi_91x-y += rsi_91x_hal.o rsi_91x-y += rsi_91x_ps.o +rsi_91x-y += rsi_91x_coex.o rsi_91x-$(CONFIG_RSI_DEBUGFS) += rsi_91x_debugfs.o rsi_usb-y += rsi_91x_usb.o rsi_91x_usb_ops.o
drivers/net/wireless/rsi/rsi_91x_coex.c new file +182 -0
182 lines not on this page · raw message
drivers/net/wireless/rsi/rsi_91x_hal.c +9 -8
@@ -31,8 +31,15 @@ int rsi_send_pkt_to_bus(struct rsi_common *common, struct sk_buff *skb)struct rsi_hw *adapter = common->priv;int status; +if (common->coex_mode >1 ) +down (&common->tx_bus_lock); + status = adapter->host_intf_ops->write_pkt (common->priv, skb->data, skb->len); + +if (common->coex_mode >1 ) +up (&common->tx_bus_lock); +return status; }
@@ -296,8 +303,7 @@ int rsi_send_data_pkt(struct rsi_common *common, struct sk_buff *skb)if (status) goto err; - status = adapter->host_intf_ops->write_pkt (common->priv, skb->data, - skb->len); + status =rsi_send_pkt_to_bus (common, skb);if (status)rsi_dbg (ERR_ZONE ,"%s: Failed to write pkt\n" , __func__);
@@ -342,8 +348,7 @@ int rsi_send_mgmt_pkt(struct rsi_common *common, goto err;rsi_prepare_mgmt_desc (common, skb); - status = adapter->host_intf_ops->write_pkt (common->priv, - (u8 *)skb->data, skb->len); + status =rsi_send_pkt_to_bus (common, skb);if (status)rsi_dbg (ERR_ZONE ,"%s: Failed to write the packet\n" , __func__);
@@ -926,10 +931,6 @@ int rsi_hal_device_init(struct rsi_hw *adapter) {struct rsi_common *common = adapter->priv; - common->coex_mode =RSI_DEV_COEX_MODE_WIFI_ALONE ; - common->oper_mode =RSI_DEV_OPMODE_WIFI_ALONE ; - adapter->device_model =RSI_DEV_9113 ; -switch (adapter->device_model) {case RSI_DEV_9113 :if (rsi_load_firmware (adapter)) {
drivers/net/wireless/rsi/rsi_91x_main.c +29 -1
@@ -20,6 +20,7 @@#include <linux/firmware.h> #include "rsi_mgmt.h" #include "rsi_common.h" +#include "rsi_coex.h" #include "rsi_hal.h" u32 rsi_zone_enabled =/* INFO_ZONE |
@@ -160,8 +161,13 @@ int rsi_read_pkt(struct rsi_common *common, u8 *rx_pkt, s32 rcv_pkt_len)switch (queueno) {case RSI_COEX_Q : -rsi_mgmt_pkt_recv (common, (frame_desc + offset)); +if (common->coex_mode >1 ) +rsi_coex_recv_pkt (common, frame_desc + offset); +else +rsi_mgmt_pkt_recv (common, + (frame_desc + offset));break ; +case RSI_WIFI_DATA_Q : skb = rsi_prepare_skb(common, (frame_desc + offset),
@@ -217,6 +223,13 @@ static void rsi_tx_scheduler_thread(struct rsi_common *common)complete_and_exit (&common->tx_thread.completion,0 ); } +enum rsi_host_intf rsi_get_host_intf (void *priv) +{ +struct rsi_common *common = (struct rsi_common *)priv; + +return common->priv->rsi_host_intf; +} +/** * rsi_91x_init() - This function initializes os interface operations. * @void: Void.
@@ -251,6 +264,7 @@ struct rsi_hw *rsi_91x_init(void)mutex_init (&common->mutex);mutex_init (&common->tx_lock);mutex_init (&common->rx_lock); +sema_init (&common->tx_bus_lock,1 ); if (rsi_create_kthread(common, &common->tx_thread,
@@ -265,6 +279,17 @@ struct rsi_hw *rsi_91x_init(void)timer_setup (&common->roc_timer, rsi_roc_timeout,0 );init_completion (&common->wlan_init_completion); common->init_done = true; + + common->coex_mode =RSI_DEV_COEX_MODE_WIFI_ALONE ; + common->oper_mode =RSI_DEV_OPMODE_WIFI_ALONE ; + adapter->device_model =RSI_DEV_9113 ; +if (common->coex_mode >1 ) { +if (rsi_coex_attach (common)) { +rsi_dbg (ERR_ZONE ,"Failed to init coex module\n" ); + goto err; + } + } +return adapter; err:
@@ -294,6 +319,9 @@ void rsi_91x_deinit(struct rsi_hw *adapter) common->init_done = false; +if (common->coex_mode >1 ) +rsi_coex_detach (common); +kfree (common);kfree (adapter->rsi_dev);kfree (adapter);
drivers/net/wireless/rsi/rsi_91x_mgmt.c +1 -1
@@ -1791,7 +1791,7 @@ static int rsi_handle_ta_confirm_type(struct rsi_common *common,return -EINVAL ; } -static int rsi_handle_card_ready (struct rsi_common *common,u8 *msg) +int rsi_handle_card_ready (struct rsi_common *common,u8 *msg) {switch (common->fsm_state) {case FSM_CARD_NOT_READY :
drivers/net/wireless/rsi/rsi_91x_sdio.c +1 -0
@@ -18,6 +18,7 @@#include <linux/module.h> #include "rsi_sdio.h" #include "rsi_common.h" +#include "rsi_coex.h" #include "rsi_hal.h" /**
drivers/net/wireless/rsi/rsi_91x_usb.c +2 -0
@@ -16,8 +16,10 @@*/ #include <linux/module.h> +#include <linux/rsi_header.h> #include "rsi_usb.h" #include "rsi_hal.h" +#include "rsi_coex.h" /** * rsi_usb_card_write() - This function writes to the USB Card.
drivers/net/wireless/rsi/rsi_coex.h new file +38 -0
@@ -0,0 +1,38 @@ +/** +* Copyright (c) 2017 Redpine Signals Inc. +* +* Permission to use, copy, modify, and/or distribute this software for any +* purpose with or without fee is hereby granted, provided that the above +* copyright notice and this permission notice appear in all copies. +* +* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES +* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF +* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR +* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES +* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN +* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF +* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. +*/ + +#ifndef __RSI_COEX_H__ +#define __RSI_COEX_H__ + +#include "rsi_common.h" + +#define RSI_COEX_TXQ_MAX_PKTS 64 +#define RSI_COEX_TXQ_WATER_MARK 50 +#define COMMON_CARD_READY_IND 0 +#define NUM_COEX_TX_QUEUES 5 + +struct rsi_coex_ctrl_block { +struct rsi_common *priv; +struct sk_buff_head coex_tx_qs[NUM_COEX_TX_QUEUES ]; +struct rsi_thread coex_tx_thread; +}; + +int rsi_coex_attach (struct rsi_common *common); +void rsi_coex_detach (struct rsi_common *common); +int rsi_coex_send_pkt (void *priv,struct sk_buff *skb,u8 proto_type); +int rsi_coex_recv_pkt (struct rsi_common *common,u8 *msg); + +#endif
drivers/net/wireless/rsi/rsi_main.h +5 -0
@@ -206,6 +206,7 @@ struct rsi_common {struct rsi_hw *priv;struct vif_priv vif_info[RSI_MAX_VIFS ]; +void *coex_cb;bool mgmt_q_block;struct version_info lmac_ver;
@@ -270,6 +271,7 @@ struct rsi_common {u8 obm_ant_sel_val;int tx_power;u8 ant_in_use; +struct semaphore tx_bus_lock;bool hibernate_resume;bool reinit_hw;u8 wow_flags;
@@ -359,4 +361,7 @@ struct rsi_host_intf_ops { u8 *fw); int (*reinit_device)(struct rsi_hw *adapter); }; + +enum rsi_host_intf rsi_get_host_intf (void *priv); +#endif
drivers/net/wireless/rsi/rsi_mgmt.h +3 -0
@@ -57,12 +57,14 @@#define WOW_PATTERN_SIZE 256/* Receive Frame Types */ +#define RSI_RX_DESC_MSG_TYPE_OFFSET 2#define TA_CONFIRM_TYPE 0x01#define RX_DOT11_MGMT 0x02#define TX_STATUS_IND 0x04#define BEACON_EVENT_IND 0x08#define PROBEREQ_CONFIRM 2#define CARD_READY_IND 0x00 +#define SLEEP_NOTIFY_IND 0x06#define RSI_DELETE_PEER 0x0#define RSI_ADD_PEER 0x1
@@ -638,6 +640,7 @@ static inline void rsi_set_len_qno(__le16 *addr, u16 len, u8 qno) *addr =cpu_to_le16 (len | ((qno &7 ) <<12 )); } +int rsi_handle_card_ready (struct rsi_common *common,u8 *msg);int rsi_mgmt_pkt_recv (struct rsi_common *common,u8 *msg);int rsi_set_vap_capabilities (struct rsi_common *common,enum opmode mode,u8 *mac_addr,u8 vap_id,u8 vap_status);
include/linux/rsi_header.h +20 -0
@@ -17,6 +17,8 @@#ifndef __RSI_HEADER_H__#define __RSI_HEADER_H__ +#include <linux/skbuff.h> +/* HAL queue information */ #define RSI_COEX_Q 0x0#define RSI_BT_Q 0x2
@@ -26,9 +28,27 @@#define RSI_BT_MGMT_Q 0x6#define RSI_BT_DATA_Q 0x7 +enum rsi_coex_queues { +RSI_COEX_Q_INVALID =-1 , +RSI_COEX_Q_COMMON =0 , +RSI_COEX_Q_BT , +RSI_COEX_Q_WLAN +}; +enum rsi_host_intf {RSI_HOST_INTF_SDIO =0 ,RSI_HOST_INTF_USB }; +struct rsi_proto_ops { +int (*coex_send_pkt)(void *priv,struct sk_buff *skb,u8 hal_queue); +enum rsi_host_intf (*get_host_intf)(void *priv); +void (*set_bt_context)(void *priv,void *context); +}; + +struct rsi_mod_ops { +int (*attach)(void *priv,struct rsi_proto_ops *ops); +void (*detach)(void *priv); +int (*recv_pkt)(void *priv,u8 *msg); +};#endif
Signature · 1 line
2.7.4
PATCH v3 5/8 Bluetooth: btrsi: add new rsi bluetooth driver
In reply to Amitkumar KarwarFrom: Prameela Rani Garnepudi <[email protected]>
Redpine bluetooth driver is a thin driver which depends on 'rsi_91x' driver for transmitting and receiving packets to/from device. It creates hci interface when attach() is called from 'rsi_91x' module.
---
v3: Made BT_RSI module by default off(Marcel)
Removed redundant exported function rsi_get_hci_ops()(Marcel)
v2: Addressed review comments from Marcel
Removed unnecessary 'depends on BT && BT_RFOMM' line in Kconfig Removed redundant BT_INFO messages
h_adapter initialization and declaration in a single line.
Removed unnecessary error checks for HCI_RUNNING and fsm_state Allocated new skb with skb_realloc_headroom() API if headroom is not sufficient Used get_unaligned_le16 helpers
Moved a structure and union from header file to btrsi.c file
--- drivers/bluetooth/Kconfig | 11 +++ drivers/bluetooth/Makefile | 2 + drivers/bluetooth/btrsi.c | 211 ++++++++++++++++++++++++++++++++++++++++++++ drivers/bluetooth/rsi_hci.h | 40 +++++++++ include/linux/rsi_header.h | 2 + 5 files changed, 266 insertions(+) create mode 100644 drivers/bluetooth/btrsi.c create mode 100644 drivers/bluetooth/rsi_hci.h
drivers/bluetooth/Kconfig +11 -0
@@ -378,4 +378,15 @@ config BT_QCOMSMD Say Y here to compile support for HCI over Qualcomm SMD into the kernel or say M to compile as a module. +config BT_RSI + tristate "Redpine HCI support" + default n + help + Redpine BT driver. + This driver handles BT traffic from upper layers and pass + to the RSI_91x coex module for further scheduling to device + + Say Y here to compile support for HCI over Redpine into the + kernel or say M to compile as a module. + endmenu
drivers/bluetooth/Makefile +2 -0
@@ -28,6 +28,8 @@ obj-$(CONFIG_BT_QCA) += btqca.o obj-$(CONFIG_BT_HCIUART_NOKIA) += hci_nokia.o +obj-$(CONFIG_BT_RSI) += btrsi.o + btmrvl-y := btmrvl_main.o btmrvl-$(CONFIG_DEBUG_FS) += btmrvl_debugfs.o
drivers/bluetooth/btrsi.c new file +211 -0
211 lines not on this page · raw message
drivers/bluetooth/rsi_hci.h new file +40 -0
@@ -0,0 +1,40 @@ +/** +* Copyright (c) 2017 Redpine Signals Inc. +* +* Permission to use, copy, modify, and/or distribute this software for any +* purpose with or without fee is hereby granted, provided that the above +* copyright notice and this permission notice appear in all copies. +* +* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES +* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF +* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR +* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES +* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN +* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF +* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. +*/ + +#ifndef __RSI_HCI_H__ +#define __RSI_HCI_H__ + +#include <net/bluetooth/bluetooth.h> +#include <net/bluetooth/hci_core.h> +#include <linux/unaligned/le_byteshift.h> +#include <linux/rsi_header.h> +#include <net/genetlink.h> + +/* RX frame types */ +#define RSI_RESULT_CONFIRM 0x80 +#define RSI_BT_PER 0x10 +#define RSI_BT_BER 0x11 +#define RSI_BT_CW 0x12 + +#define RSI_HEADROOM_FOR_BT_HAL 16 + +#define RSI_FRAME_DESC_SIZE 16 + +int rsi_hci_attach (void *priv,struct rsi_proto_ops *ops); +void rsi_hci_detach (void *priv); +int rsi_hci_recv_pkt (void *data,u8 *pkt); + +#endif
include/linux/rsi_header.h +2 -0
@@ -51,4 +51,6 @@ struct rsi_mod_ops {void (*detach)(void *priv); int (*recv_pkt)(void *priv, u8 *msg); }; + +extern const struct rsi_mod_ops rsi_bt_ops;#endif
Signature · 1 line
2.7.4
Marcel Holtmann
maintainerRe: [v3 5/8] Bluetooth: btrsi: add new rsi bluetooth driver
Hi Amitkumar,
Quoted 307 lines
Redpine bluetooth driver is a thin driver which depends on '
rsi_91x' driver for transmitting and receiving packets to/from device. It creates hci interface whenattach()is called from 'rsi_91x' module.Signed-off-by Prameela Rani Garnepudi <[email protected]>Signed-off-by Siva Rebbagondla <[email protected]>Signed-off-by Amitkumar Karwar <[email protected]>---
v3: MadeBT_RSImodule by default off(Marcel)
Removed redundant exported function rsi_get_hci_ops()(Marcel)
v2: Addressed review comments from Marcel
Removed unnecessary 'depends on BT &&BT_RFOMM' line inKconfigRemoved redundantBT_INFOmessages
h_adapterinitialization and declaration in a single line.
Removed unnecessary error checks forHCI_RUNNINGandfsm_stateAllocated new skb withskb_realloc_headroom()API if headroom is not sufficient Usedget_unaligned_le16helpers
Moved a structure and union from header file tobtrsi.cfile
---drivers/bluetooth/Kconfig | 11 +++ drivers/bluetooth/Makefile | 2 + drivers/bluetooth/btrsi.c | 211 ++++++++++++++++++++++++++++++++++++++++++++ drivers/bluetooth/rsi_hci.h | 40 +++++++++ include/linux/rsi_header.h | 2 + 5 files changed, 266 insertions(+)create mode 100644
drivers/bluetooth/btrsi.c
create mode 100644drivers/bluetooth/rsi_hci.hdrivers/bluetooth/Kconfig +11
-0@@ -378,4 +378,15 @@ config BT_QCOMSMD Say Y here to compile support for HCI over Qualcomm SMD into the kernel or say M to compile as a module. +config BT_RSI + tristate "Redpine HCI support" + default n + help + Redpine BT driver. + This driver handles BT traffic from upper layers and pass + to the RSI_91x coex module for further scheduling to device + + Say Y here to compile support for HCI over Redpine into the + kernel or say M to compile as a module. +endmenu
drivers/bluetooth/Makefile +0
-0@@ -28,6 +28,8 @@ obj-$(CONFIG_BT_QCA) += btqca.oobj-$(CONFIG_BT_HCIUART_NOKIA) += hci_nokia.o
drivers/bluetooth/Makefile +2
-0+obj-$(CONFIG_BT_RSI) += btrsi.o +btmrvl-y := btmrvl_main.o
btmrvl-$(CONFIG_DEBUG_FS) += btmrvl_debugfs.odrivers/bluetooth/btrsi.c new file +211
-0@@ -0,0 +1,211 @@ +/** +* Copyright (c) 2017 Redpine Signals Inc. +* +* Permission to use, copy, modify, and/or distribute this software for any +* purpose with or without fee is hereby granted, provided that the above +* copyright notice and this permission notice appear in all copies. +* +* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES +* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF +* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR +e* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES +* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN +* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF +* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. +*/ +#include <linux/version.h> +#include <linux/module.h> +#include <linux/kernel.h> +#include "rsi_hci.h" + +struct rsi_hci_adapter { +void *priv; +struct rsi_proto_ops *proto_ops; +struct hci_dev *hdev; +}; + +const struct rsi_mod_ops rsi_bt_ops = { + .attach = rsi_hci_attach, + .detach = rsi_hci_detach, + .recv_pkt = rsi_hci_recv_pkt, +}; +EXPORT_SYMBOL (rsi_bt_ops); + +static int rsi_hci_open (struct hci_dev *hdev) +{ +return 0 ; +} + +static int rsi_hci_close (struct hci_dev *hdev) +{ +return 0 ; +} + +static int rsi_hci_flush (struct hci_dev *hdev) +{ +return 0 ; +} + +static int rsi_hci_send_pkt (struct hci_dev *hdev,struct sk_buff *skb) +{ +struct rsi_hci_adapter *h_adapter =hci_get_drvdata (hdev); +struct sk_buff *new_skb =NULL ; + +switch (bt_cb (skb)->pkt_type) { +case HCI_COMMAND_PKT : + hdev->stat.cmd_tx++; +break ; + +case HCI_ACLDATA_PKT : + hdev->stat.acl_tx++; +break ; + +case HCI_SCODATA_PKT : + hdev->stat.sco_tx++; +break ; + } + +if (skb_headroom (skb) <RSI_HEADROOM_FOR_BT_HAL ) { +/* Insufficient skb headroom - allocate a new skb */ + new_skb =skb_realloc_headroom (skb,RSI_HEADROOM_FOR_BT_HAL ); +if (unlikely (!new_skb)) +return -ENOMEM ; +bt_cb (new_skb)->pkt_type =bt_cb (skb)->pkt_type; +kfree_skb (skb); + skb = new_skb; + } + +return h_adapter->proto_ops->coex_send_pkt (h_adapter->priv, skb, +RSI_BT_Q ); +} + +int rsi_hci_recv_pkt (void *priv,u8 *pkt) +{ +struct rsi_hci_adapter *h_adapter = (struct rsi_hci_adapter *)priv; +struct hci_dev *hdev = h_adapter->hdev; +struct sk_buff *skb; + +int pkt_len =get_unaligned_le16 (pkt) &0x0fff ; +u8 queue_no = (get_unaligned_le16 (pkt) &0x7000 ) >>12 ; + +if (queue_no ==RSI_BT_MGMT_Q ) { +u8 msg_type = pkt[14 ] &0xFF ; + +switch (msg_type) { +case RSI_RESULT_CONFIRM : +bt_dev_info (hdev,"BT Result Confirm" ); +return 0 ; +case RSI_BT_BER : +bt_dev_info (hdev,"BT Ber" ); +return 0 ; +case RSI_BT_CW : +bt_dev_info (hdev,"BT CW" ); +return 0 ; +default : +break ; + } + } + + skb =dev_alloc_skb (pkt_len); +if (!skb) +return -ENOMEM ; + +memcpy (skb->data, pkt +RSI_FRAME_DESC_SIZE , pkt_len); +skb_put (skb, pkt_len); + h_adapter->hdev->stat.byte_rx += skb->len; + + skb->dev = (void *)hdev; +bt_cb (skb)->pkt_type = pkt[14 ]; + +return hci_recv_frame (hdev, skb); +} + +int rsi_hci_attach (void *priv,struct rsi_proto_ops *ops) +{ +struct rsi_hci_adapter *h_adapter =NULL ; +struct hci_dev *hdev; +int status =0 ; + + h_adapter =kzalloc (sizeof (*h_adapter),GFP_KERNEL ); +if (!h_adapter) +return -ENOMEM ; + + h_adapter->priv = priv; + ops->set_bt_context (priv, h_adapter); + h_adapter->proto_ops = ops; + + hdev =hci_alloc_dev (); +if (!hdev) { +BT_ERR ("Failed to alloc HCI device\n" ); + goto err; + } + + h_adapter->hdev = hdev; + +if (ops->get_host_intf (priv) ==RSI_HOST_INTF_SDIO ) + hdev->bus =HCI_SDIO ; +else + hdev->bus =HCI_USB ; + +hci_set_drvdata (hdev, h_adapter); + hdev->dev_type =HCI_PRIMARY ; + hdev->open = rsi_hci_open; + hdev->close = rsi_hci_close; + hdev->flush = rsi_hci_flush; + hdev->send = rsi_hci_send_pkt; + + status =hci_register_dev (hdev); +if (status <0 ) { +BT_ERR ("%s: HCI registration failed with errcode %d\n" , + __func__, status); + goto err; + } + +return 0 ; +err: +if (hdev) { +hci_unregister_dev (hdev); +hci_free_dev (hdev); + h_adapter->hdev =NULL ; + } +kfree (h_adapter); + +return -EINVAL ; +} + +void rsi_hci_detach (void *priv) +{ +struct rsi_hci_adapter *h_adapter = (struct rsi_hci_adapter *)priv; +struct hci_dev *hdev; + +if (!h_adapter) +return ; + + hdev = h_adapter->hdev; +if (hdev) { +hci_unregister_dev (hdev); +hci_free_dev (hdev); + h_adapter->hdev =NULL ; + } + +kfree (h_adapter); +} + +static int rsi_91x_bt_module_init (void ) +{ +BT_INFO ("%s: BT Module init called\n" , __func__); + +return 0 ; +} + +static void rsi_91x_bt_module_exit (void ) +{ +BT_INFO ("%s: BT Module exit called\n" , __func__); +} + +module_init (rsi_91x_bt_module_init); +module_exit (rsi_91x_bt_module_exit); +MODULE_AUTHOR ("Redpine Signals Inc" ); +MODULE_DESCRIPTION ("RSI BT driver" ); +MODULE_SUPPORTED_DEVICE ("RSI-BT" ); +MODULE_LICENSE ("Dual BSD/GPL" );drivers/bluetooth/rsi_hci.h new file +22
-0@@ -0,0 +1,40 @@ +/** +* Copyright (c) 2017 Redpine Signals Inc. +* +* Permission to use, copy, modify, and/or distribute this software for any +* purpose with or without fee is hereby granted, provided that the above +* copyright notice and this permission notice appear in all copies. +* +* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES +* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF +* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR +* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES +* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN +* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF +* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. +*/ + +#ifndef __RSI_HCI_H__ +#define __RSI_HCI_H__ + +#include <net/bluetooth/bluetooth.h> +#include <net/bluetooth/hci_core.h> +#include <linux/unaligned/le_byteshift.h>
drivers/bluetooth/rsi_hci.h line 32
Quoted 10 lines
drivers/bluetooth/rsi_hci.h new file +10
-0+#include <linux/rsi_header.h> +#include <net/genetlink.h> + +/* RX frame types */ +#define RSI_RESULT_CONFIRM 0x80 +#define RSI_BT_PER 0x10 +#define RSI_BT_BER 0x11 +#define RSI_BT_CW 0x12 + +#define RSI_HEADROOM_FOR_BT_HAL 16
I still like to see changes to the BT core that allows the driver to specify how headroom it needs. This can be follow up patches, but we should do that since reallocating the SKBs all the time is also pointless.
drivers/bluetooth/rsi_hci.h line 40
Quoted 8 lines
drivers/bluetooth/rsi_hci.h new file +8
-0+ +#define RSI_FRAME_DESC_SIZE 16 + +int rsi_hci_attach (void *priv,struct rsi_proto_ops *ops); +void rsi_hci_detach (void *priv); +int rsi_hci_recv_pkt (void *data,u8 *pkt); + +#endif
I have no idea why this header file is needed at all. Fold this into btrsi.c and make the rsi_hci_* functions static.
include/linux/rsi_header.h struct rsi_mod_ops { · line 55
Quoted 10 lines
include/linux/rsi_header.h +2
-0@@ -51,4 +51,6 @@ struct rsi_mod_ops {void (*detach)(void *priv);int (*recv_pkt)(void *priv,u8 *msg); }; + +extern const struct rsi_mod_ops rsi_bt_ops;
If you expose rsi_hci_attach via rsi_bt_ops, then there is no need for making rsi_hci_attach also public. I mentioned this in the first review as well. I do not get it. Either you expose rsi_bt_ops from this module or you expose the rsi_hci_* function, but both is totally pointless.
Regards
Marcel
Re: [v3 5/8] Bluetooth: btrsi: add new rsi bluetooth driver
On Fri, Dec 1, 2017 at 4:24 PM, Marcel Holtmann <[email protected]> wrote= :
Quoted 19 lines
Hi Amitkumar,
Quoted 17 lines
Redpine bluetooth driver is a thin driver which depends on '
rsi_91x' driver for transmitting and receiving packets to/from device. It creates hci interface whenattach()is called from 'rsi_91x' module.Signed-off-by Prameela Rani Garnepudi <[email protected]>Signed-off-by Siva Rebbagondla <[email protected]>Signed-off-by Amitkumar Karwar <[email protected]>---
v3: MadeBT_RSImodule by default off(Marcel)
Removed redundant exported function rsi_get_hci_ops()(Marcel)
v2: Addressed review comments from Marcel
Removed unnecessary 'depends on BT &&BT_RFOMM' line inKconfigRemoved redundantBT_INFOmessages
h_adapterinitialization and declaration in a single line. Removed unnecessary error checks forHCI_RUNNINGandfsm_stateAllocated new skb withskb_realloc_headroom()API if headroom is not =
sufficient
Quoted 6 lines
Quoted 6 lines
Used
get_unaligned_le16helpers
Moved a structure and union from header file tobtrsi.cfile
---drivers/bluetooth/Kconfig | 11 +++ drivers/bluetooth/Makefile | 2 + drivers/bluetooth/btrsi.c | 211 ++++++++++++++++++++++++++++++++++++++=
++++++
Quoted 39 lines
Quoted 39 lines
drivers/bluetooth/rsi_hci.h| 40 +++++++++include/linux/rsi_header.h| 2 +5 files changed, 266 insertions(+)create mode 100644
drivers/bluetooth/btrsi.c
create mode 100644drivers/bluetooth/rsi_hci.hdrivers/bluetooth/Kconfig +11
-0@@ -378,4 +378,15 @@ config BT_QCOMSMD Say Y here to compile support for HCI over Qualcomm SMD into the kernel or say M to compile as a module. +config BT_RSI + tristate "Redpine HCI support" + default n + help + Redpine BT driver. + This driver handles BT traffic from upper layers and pass + to the RSI_91x coex module for further scheduling to device + + Say Y here to compile support for HCI over Redpine into the + kernel or say M to compile as a module. +endmenu
drivers/bluetooth/Makefile +0
-0@@ -28,6 +28,8 @@ obj-$(CONFIG_BT_QCA) +=3D btqca.oobj-$(CONFIG_BT_HCIUART_NOKIA) +=3D hci_nokia.o
drivers/bluetooth/Makefile +2
-0+obj-$(CONFIG_BT_RSI) +=3D btrsi.o +btmrvl-y :=3D btmrvl_main.o
btmrvl-$(CONFIG_DEBUG_FS) +=3D btmrvl_debugfs.o
Quoted 10 lines
drivers/bluetooth/btrsi.c line 4
Quoted 10 lines
drivers/bluetooth/btrsi.c new file +4
-0@@ -0,0 +1,211 @@ +/** +* Copyright (c) 2017 Redpine Signals Inc. +* +* Permission to use, copy, modify, and/or distribute this software for=
any
Quoted 1 line
drivers/bluetooth/btrsi.c line 5
Quoted 1 line
drivers/bluetooth/btrsi.c new file +1
-0+* purpose with or without fee is hereby granted, provided that the abo=
ve
Quoted 3 lines
drivers/bluetooth/btrsi.c
Quoted 3 lines
drivers/bluetooth/btrsi.c new file +3
-0+* copyright notice and this permission notice appear in all copies. +* +* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRAN=
TIES
Quoted 2 lines
drivers/bluetooth/btrsi.c line 10
Quoted 2 lines
drivers/bluetooth/btrsi.c new file +2
-0+* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF +* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE =
FOR
Quoted 1 line
drivers/bluetooth/btrsi.c line 11
Quoted 1 line
drivers/bluetooth/btrsi.c new file +1
-0+e* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAG=
ES
Quoted 1 line
drivers/bluetooth/btrsi.c line 12
Quoted 1 line
drivers/bluetooth/btrsi.c new file +1
-0+* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN A=
N
Quoted 1 line
drivers/bluetooth/btrsi.c line 13
Quoted 1 line
drivers/bluetooth/btrsi.c new file +1
-0+* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT=
OF
Quoted 49 lines
Quoted 49 lines
drivers/bluetooth/btrsi.c new file +49
-0+* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. +*/ +#include <linux/version.h> +#include <linux/module.h> +#include <linux/kernel.h> +#include "rsi_hci.h" + +struct rsi_hci_adapter { +void *priv; +struct rsi_proto_ops *proto_ops; +struct hci_dev *hdev; +}; + +const struct rsi_mod_ops rsi_bt_ops =3D { + .attach =3D rsi_hci_attach, + .detach =3D rsi_hci_detach, + .recv_pkt =3D rsi_hci_recv_pkt, +}; +EXPORT_SYMBOL (rsi_bt_ops ); + +static int rsi_hci_open (struct hci_dev *hdev) +{ +return 0 ; +} + +static int rsi_hci_close (struct hci_dev *hdev) +{ +return 0 ; +} + +static int rsi_hci_flush (struct hci_dev *hdev) +{ +return 0 ; +} + +static int rsi_hci_send_pkt (struct hci_dev *hdev,struct sk_buff *skb) +{ + struct rsi_hci_adapter *h_adapter =3D hci_get_drvdata(hdev); + struct sk_buff *new_skb =3D NULL; + +switch (bt_cb (skb)->pkt_type) { +case HCI_COMMAND_PKT : + hdev->stat.cmd_tx++; +break ; + +case HCI_ACLDATA_PKT : + hdev->stat.acl_tx++; +break ; +
Quoted 8 lines
drivers/bluetooth/btrsi.c
Quoted 8 lines
drivers/bluetooth/btrsi.c new file +8
-0+case HCI_SCODATA_PKT : + hdev->stat.sco_tx++; +break ; + } + + if (skb_headroom(skb) < RSI_HEADROOM_FOR_BT_HAL) { + /* Insufficient skb headroom - allocate a new skb */ + new_skb =3D skb_realloc_headroom(skb, RSI_HEADROOM_FOR_BT_=
HAL);
Quoted 6 lines
Quoted 6 lines
drivers/bluetooth/btrsi.c new file +6
-0+if (unlikely (!new_skb)) +return -ENOMEM ; + bt_cb(new_skb)->pkt_type =3D bt_cb(skb)->pkt_type; +kfree_skb (skb); + skb =3D new_skb; + }
Quoted 8 lines
drivers/bluetooth/btrsi.c
Quoted 8 lines
drivers/bluetooth/btrsi.c new file +8
-0+ +return h_adapter->proto_ops->coex_send_pkt (h_adapter->priv, skb, +RSI_BT_Q ); +} + +int rsi_hci_recv_pkt(void *priv, u8 *pkt) +{ + struct rsi_hci_adapter *h_adapter =3D (struct rsi_hci_adapter *)pr=
iv;
Quoted 86 lines
Quoted 86 lines
drivers/bluetooth/btrsi.c new file +86
-0+ struct hci_dev *hdev =3D h_adapter->hdev; +struct sk_buff *skb; + + int pkt_len =3D get_unaligned_le16(pkt) & 0x0fff; +u8 queue_no =3D (get_unaligned_le16 (pkt) &0x7000 ) >>12 ; + + if (queue_no =3D=3D RSI_BT_MGMT_Q) { + u8 msg_type =3D pkt[14] & 0xFF; + +switch (msg_type) { +case RSI_RESULT_CONFIRM : +bt_dev_info (hdev,"BT Result Confirm" ); +return 0 ; +case RSI_BT_BER : +bt_dev_info (hdev,"BT Ber" ); +return 0 ; +case RSI_BT_CW : +bt_dev_info (hdev,"BT CW" ); +return 0 ; +default : +break ; + } + } + + skb =3D dev_alloc_skb(pkt_len); +if (!skb) +return -ENOMEM ; + +memcpy (skb->data, pkt +RSI_FRAME_DESC_SIZE , pkt_len); +skb_put (skb, pkt_len); + h_adapter->hdev->stat.byte_rx +=3D skb->len; + + skb->dev =3D (void *)hdev; + bt_cb(skb)->pkt_type =3D pkt[14]; + +return hci_recv_frame (hdev, skb); +} + +int rsi_hci_attach (void *priv,struct rsi_proto_ops *ops) +{ + struct rsi_hci_adapter *h_adapter =3D NULL; +struct hci_dev *hdev; + int status =3D 0; + + h_adapter =3D kzalloc(sizeof(*h_adapter), GFP_KERNEL); +if (!h_adapter) +return -ENOMEM ; + + h_adapter->priv =3D priv; + ops->set_bt_context (priv, h_adapter); + h_adapter->proto_ops =3D ops; + + hdev =3D hci_alloc_dev(); +if (!hdev) { +BT_ERR ("Failed to alloc HCI device\n" ); + goto err; + } + + h_adapter->hdev =3D hdev; + + if (ops->get_host_intf(priv) =3D=3D RSI_HOST_INTF_SDIO) + hdev->bus =3D HCI_SDIO; +else + hdev->bus =3D HCI_USB; + +hci_set_drvdata (hdev, h_adapter); + hdev->dev_type =3D HCI_PRIMARY; + hdev->open =3D rsi_hci_open; + hdev->close =3D rsi_hci_close; + hdev->flush =3D rsi_hci_flush; + hdev->send =3D rsi_hci_send_pkt; + + status =3D hci_register_dev(hdev); +if (status <0 ) { +BT_ERR ("%s: HCI registration failed with errcode %d\n" , + __func__, status); + goto err; + } + +return 0 ; +err: +if (hdev) { +hci_unregister_dev (hdev); +hci_free_dev (hdev); + h_adapter->hdev =3D NULL; + }
Quoted 8 lines
drivers/bluetooth/btrsi.c
Quoted 8 lines
drivers/bluetooth/btrsi.c new file +8
-0+kfree (h_adapter); + +return -EINVAL ; +} + +void rsi_hci_detach(void *priv) +{ + struct rsi_hci_adapter *h_adapter =3D (struct rsi_hci_adapter *)pr=
iv;
Quoted 35 lines
Quoted 35 lines
drivers/bluetooth/btrsi.c new file +33
-0+struct hci_dev *hdev; + +if (!h_adapter) +return ; + + hdev =3D h_adapter->hdev; +if (hdev) { +hci_unregister_dev (hdev); +hci_free_dev (hdev); + h_adapter->hdev =3D NULL; + } + +kfree (h_adapter); +} + +static int rsi_91x_bt_module_init (void ) +{ +BT_INFO ("%s: BT Module init called\n" , __func__); + +return 0 ; +} + +static void rsi_91x_bt_module_exit (void ) +{ +BT_INFO ("%s: BT Module exit called\n" , __func__); +} + +module_init (rsi_91x_bt_module_init); +module_exit (rsi_91x_bt_module_exit); +MODULE_AUTHOR ("Redpine Signals Inc" ); +MODULE_DESCRIPTION ("RSI BT driver" ); +MODULE_SUPPORTED_DEVICE ("RSI-BT" ); +MODULE_LICENSE ("Dual BSD/GPL" );drivers/bluetooth/rsi_hci.h new file +0
-0
Quoted 8 lines
drivers/bluetooth/rsi_hci.h line 4
Quoted 8 lines
index 0000000..6fc7757
drivers/bluetooth/rsi_hci.h new file +4
-0@@ -0,0 +1,40 @@ +/** +* Copyright (c) 2017 Redpine Signals Inc. +* +* Permission to use, copy, modify, and/or distribute this software for=
any
Quoted 1 line
drivers/bluetooth/rsi_hci.h line 5
Quoted 1 line
drivers/bluetooth/rsi_hci.h new file +1
-0+* purpose with or without fee is hereby granted, provided that the abo=
ve
Quoted 3 lines
drivers/bluetooth/rsi_hci.h line 8
Quoted 3 lines
drivers/bluetooth/rsi_hci.h new file +3
-0+* copyright notice and this permission notice appear in all copies. +* +* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRAN=
TIES
Quoted 2 lines
drivers/bluetooth/rsi_hci.h line 10
Quoted 2 lines
drivers/bluetooth/rsi_hci.h new file +2
-0+* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF +* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE =
FOR
Quoted 1 line
drivers/bluetooth/rsi_hci.h line 11
Quoted 1 line
drivers/bluetooth/rsi_hci.h new file +1
-0+* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAG=
ES
Quoted 1 line
drivers/bluetooth/rsi_hci.h line 12
Quoted 1 line
drivers/bluetooth/rsi_hci.h new file +1
-0+* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN A=
N
Quoted 1 line
drivers/bluetooth/rsi_hci.h line 13
Quoted 1 line
drivers/bluetooth/rsi_hci.h new file +1
-0+* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT=
OF
Quoted 13 lines
Quoted 13 lines
drivers/bluetooth/rsi_hci.h new file +13
-0+* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. +*/ + +#ifndef __RSI_HCI_H__ +#define __RSI_HCI_H__ + +#include <net/bluetooth/bluetooth.h> +#include <net/bluetooth/hci_core.h> +#include <linux/unaligned/le_byteshift.h> +#include <linux/rsi_header.h> +#include <net/genetlink.h> + +/* RX frame types */
Quoted 8 lines
drivers/bluetooth/rsi_hci.h line 32
Quoted 6 lines
drivers/bluetooth/rsi_hci.h new file +6
-0+#define RSI_RESULT_CONFIRM 0x80 +#define RSI_BT_PER 0x10 +#define RSI_BT_BER 0x11 +#define RSI_BT_CW 0x12 + +#define RSI_HEADROOM_FOR_BT_HAL 16I still like to see changes to the BT core that allows the driver to spec=
ify how headroom it needs. This can be follow up patches, but we should do = that since reallocating the SKBs all the time is also pointless.
Ok. I will prepare follow up patch for this.
Quoted 11 lines
drivers/bluetooth/rsi_hci.h line 40
Quoted 9 lines
drivers/bluetooth/rsi_hci.h new file +8
-0+ +#define RSI_FRAME_DESC_SIZE 16 + +int rsi_hci_attach (void *priv,struct rsi_proto_ops *ops); +void rsi_hci_detach (void *priv); +int rsi_hci_recv_pkt (void *data,u8 *pkt); + +#endif I have no idea why this header file is needed at all. Fold this into btrs=
i.c and make the rsi_hci_* functions static.
I will take care of this in v4.
Quoted 13 lines
include/linux/rsi_header.h struct rsi_mod_ops { · line 55
Quoted 11 lines
include/linux/rsi_header.h +2
-0@@ -51,4 +51,6 @@ struct rsi_mod_ops {void (*detach)(void *priv);int (*recv_pkt)(void *priv,u8 *msg); }; + +extern const struct rsi_mod_ops rsi_bt_ops;If you expose
rsi_hci_attachviarsi_bt_ops, then there is no need for ma=
king rsi_hci_attach also public. I mentioned this in the first review as we= ll. I do not get it. Either you expose rsi_bt_ops from this module or you e= xpose the rsi_hci_* function, but both is totally pointless.
Quoted 1 line
Got it. I will get rid of header file and make these functions static
Regards,
Amitkumar
PATCH v3 6/8 rsi: handle BT traffic in driver
In reply to Amitkumar KarwarFrom: Siva Rebbagondla <[email protected]>
BT frames are passed through coex and hal modules to BUS. After firmware is loaded, based on the operating mode CARD READY frame comes for each protocol. When BT card ready is received, BT attach is called.
Protocol operations are exchanged between the modules at initialization time.
---
v3: bt_ops need not be present structure g_proto_ops. It is removed.
v2: WLAN module depends on BT module. Updated in Kconfig
--- drivers/net/wireless/rsi/Kconfig | 2 +- drivers/net/wireless/rsi/rsi_91x_coex.c | 4 ++- drivers/net/wireless/rsi/rsi_91x_core.c | 16 ++++++++---- drivers/net/wireless/rsi/rsi_91x_hal.c | 39 +++++++++++++++++++++++++++++ drivers/net/wireless/rsi/rsi_91x_main.c | 31 +++++++++++++++++++++++ drivers/net/wireless/rsi/rsi_91x_sdio_ops.c | 1 + drivers/net/wireless/rsi/rsi_common.h | 1 + drivers/net/wireless/rsi/rsi_hal.h | 10 ++++++++ drivers/net/wireless/rsi/rsi_main.h | 3 +++ 9 files changed, 100 insertions(+), 7 deletions(-)
drivers/net/wireless/rsi/Kconfig +1 -1
@@ -13,7 +13,7 @@ if WLAN_VENDOR_RSI config RSI_91X tristate "Redpine Signals Inc 91x WLAN driver support" - depends on MAC80211 + depends on MAC80211 && BT_RSI ---help--- This option enabes support for RSI 1x1 devices. Select M (recommended), if you have a RSI 1x1 wireless module.
drivers/net/wireless/rsi/rsi_91x_coex.c +3 -1
@@ -48,8 +48,10 @@ static void rsi_coex_sched_tx_pkts(struct rsi_coex_ctrl_block *coex_cb)break ; } -if (coex_q ==RSI_COEX_Q_BT ) +if (coex_q ==RSI_COEX_Q_BT ) { skb =skb_dequeue (&coex_cb->coex_tx_qs[RSI_COEX_Q_BT ]); +rsi_send_bt_pkt (coex_cb->priv, skb); + } } }
drivers/net/wireless/rsi/rsi_91x_core.c +11 -5
@@ -17,6 +17,7 @@#include "rsi_mgmt.h" #include "rsi_common.h" #include "rsi_hal.h" +#include "rsi_coex.h" /** * rsi_determine_min_weight_queue() - This function determines the queue with
@@ -301,14 +302,19 @@ void rsi_core_qos_processor(struct rsi_common *common)mutex_unlock (&common->tx_lock);break ; } - -if (q_num ==MGMT_SOFT_Q ) { - status =rsi_send_mgmt_pkt (common, skb); - }else if (q_num ==MGMT_BEACON_Q ) { +if (q_num ==MGMT_BEACON_Q ) { status =rsi_send_pkt_to_bus (common, skb);dev_kfree_skb (skb); }else { - status =rsi_send_data_pkt (common, skb); +if (common->coex_mode >1 ) { + status =rsi_coex_send_pkt (common, skb, +RSI_WLAN_Q ); + }else { +if (q_num ==MGMT_SOFT_Q ) + status =rsi_send_mgmt_pkt (common, skb); +else + status =rsi_send_data_pkt (common, skb); + } }if (status) {
drivers/net/wireless/rsi/rsi_91x_hal.c +39 -0
@@ -15,6 +15,7 @@*/ #include <linux/firmware.h> +#include <net/bluetooth/bluetooth.h> #include "rsi_mgmt.h" #include "rsi_hal.h" #include "rsi_sdio.h"
@@ -24,6 +25,7 @@static struct ta_metadata metadata_flash_content[] = { {"flash_content" ,0x00010000 }, {"rsi/rs9113_wlan_qspi.rps" ,0x00010000 }, + {"rsi/rs9113_wlan_bt_dual_mode.rps" ,0x00010000 }, };int rsi_send_pkt_to_bus (struct rsi_common *common,struct sk_buff *skb)
@@ -357,6 +359,43 @@ int rsi_send_mgmt_pkt(struct rsi_common *common,return status; } +int rsi_send_bt_pkt (struct rsi_common *common,struct sk_buff *skb) +{ +int status = -EINVAL ; +u8 header_size =0 ; +struct rsi_bt_desc *bt_desc; +u8 queueno = ((skb->data[1 ] >>4 ) &0xf ); + +if (queueno ==RSI_BT_MGMT_Q ) { + status =rsi_send_pkt_to_bus (common, skb); +if (status) +rsi_dbg (ERR_ZONE ,"%s: Failed to write bt mgmt pkt\n" , + __func__); + goto out; + } + header_size =FRAME_DESC_SZ ; +if (header_size >skb_headroom (skb)) { +rsi_dbg (ERR_ZONE ,"%s: Not enough headroom\n" , __func__); + status = -ENOSPC ; + goto out; + } +skb_push (skb, header_size); +memset (skb->data,0 , header_size); + bt_desc = (struct rsi_bt_desc *)skb->data; + +rsi_set_len_qno (&bt_desc->len_qno, (skb->len -FRAME_DESC_SZ ), +RSI_BT_DATA_Q ); + bt_desc->bt_pkt_type =cpu_to_le16 (bt_cb (skb)->pkt_type); + + status =rsi_send_pkt_to_bus (common, skb); +if (status) +rsi_dbg (ERR_ZONE ,"%s: Failed to write bt pkt\n" , __func__); + +out: +dev_kfree_skb (skb); +return status; +} +int rsi_prepare_beacon (struct rsi_common *common,struct sk_buff *skb) {struct rsi_hw *adapter = (struct rsi_hw *)common->priv;
drivers/net/wireless/rsi/rsi_91x_main.c +31 -0
@@ -18,6 +18,7 @@#include <linux/module.h> #include <linux/firmware.h> +#include <linux/rsi_header.h> #include "rsi_mgmt.h" #include "rsi_common.h" #include "rsi_coex.h"
@@ -35,6 +36,12 @@ u32 rsi_zone_enabled = /* INFO_ZONE |0 ;EXPORT_SYMBOL_GPL (rsi_zone_enabled); +static struct rsi_proto_ops g_proto_ops = { + .coex_send_pkt = rsi_coex_send_pkt, + .get_host_intf = rsi_get_host_intf, + .set_bt_context = rsi_set_bt_context, +}; +/** * rsi_dbg() - This function outputs informational messages. * @zone: Zone of interest for output message.
@@ -144,6 +151,7 @@ int rsi_read_pkt(struct rsi_common *common, u8 *rx_pkt, s32 rcv_pkt_len)u32 index, length =0 , queueno =0 ;u16 actual_length =0 , offset;struct sk_buff *skb =NULL ; +u8 bt_pkt_type; index =0 ; do {
@@ -183,6 +191,22 @@ int rsi_read_pkt(struct rsi_common *common, u8 *rx_pkt, s32 rcv_pkt_len)rsi_mgmt_pkt_recv (common, (frame_desc + offset));break ; +case RSI_BT_MGMT_Q : +case RSI_BT_DATA_Q : +#define BT_RX_PKT_TYPE_OFST 14 +#define BT_CARD_READY_IND 0x89 + bt_pkt_type = frame_desc[offset +BT_RX_PKT_TYPE_OFST ]; +if (bt_pkt_type ==BT_CARD_READY_IND ) { +rsi_dbg (INFO_ZONE ,"BT Card ready recvd\n" ); +if (rsi_bt_ops.attach (common, &g_proto_ops)) +rsi_dbg (ERR_ZONE , +"Failed to attach BT module\n" ); + }else { + rsi_bt_ops.recv_pkt (common->bt_adapter, + frame_desc + offset); + } +break ; +default :rsi_dbg (ERR_ZONE ,"%s: pkt from invalid queue: %d\n" , __func__, queueno);
@@ -230,6 +254,13 @@ enum rsi_host_intf rsi_get_host_intf(void *priv)return common->priv->rsi_host_intf; } +void rsi_set_bt_context (void *priv,void *bt_context) +{ +struct rsi_common *common = (struct rsi_common *)priv; + + common->bt_adapter = bt_context; +} +/** * rsi_91x_init() - This function initializes os interface operations. * @void: Void.
drivers/net/wireless/rsi/rsi_91x_sdio_ops.c +1 -0
@@ -16,6 +16,7 @@*/ #include <linux/firmware.h> +#include <linux/rsi_header.h> #include "rsi_sdio.h" #include "rsi_common.h"
drivers/net/wireless/rsi/rsi_common.h +1 -0
@@ -62,6 +62,7 @@ static inline int rsi_create_kthread(struct rsi_common *common, u8 *name) {init_completion (&thread->completion); +atomic_set (&thread->thread_done,0 ); thread->task =kthread_run (func_ptr, common,"%s" , name);if (IS_ERR (thread->task))return (int )PTR_ERR (thread->task);
drivers/net/wireless/rsi/rsi_hal.h +10 -0
@@ -145,8 +145,18 @@ struct rsi_data_desc { u8 sta_id; } __packed; +struct rsi_bt_desc { +__le16 len_qno; +__le16 reserved1; +__le32 reserved2; +__le32 reserved3; +__le16 reserved4; +__le16 bt_pkt_type; +} __packed; +int rsi_hal_device_init (struct rsi_hw *adapter);int rsi_prepare_beacon (struct rsi_common *common,struct sk_buff *skb);int rsi_send_pkt_to_bus (struct rsi_common *common,struct sk_buff *skb); +int rsi_send_bt_pkt (struct rsi_common *common,struct sk_buff *skb);#endif
drivers/net/wireless/rsi/rsi_main.h +3 -0
@@ -290,6 +290,8 @@ struct rsi_common {bool p2p_enabled;struct timer_list roc_timer;struct ieee80211_vif *roc_vif; + +void *bt_adapter; };struct eepromrw_info {
@@ -363,5 +365,6 @@ struct rsi_host_intf_ops { };enum rsi_host_intf rsi_get_host_intf (void *priv); +void rsi_set_bt_context (void *priv,void *bt_context);#endif
Signature · 1 line
2.7.4
PATCH v3 7/8 rsi: add module parameter operating mode
In reply to Amitkumar KarwarFrom: Prameela Rani Garnepudi <[email protected]>
Operating mode determines the support for other protocols. This is made as module parameter for better usage.
--- drivers/net/wireless/rsi/rsi_91x_main.c | 57 ++++++++++++++++++++++++++++----- drivers/net/wireless/rsi/rsi_91x_sdio.c | 10 +++++- drivers/net/wireless/rsi/rsi_91x_usb.c | 10 +++++- drivers/net/wireless/rsi/rsi_common.h | 2 +- drivers/net/wireless/rsi/rsi_hal.h | 11 +++++++ 5 files changed, 79 insertions(+), 11 deletions(-)
drivers/net/wireless/rsi/rsi_91x_main.c +49 -8
@@ -68,8 +68,24 @@ EXPORT_SYMBOL_GPL(rsi_dbg);static char *opmode_str (int oper_mode) {switch (oper_mode) { -case RSI_DEV_OPMODE_WIFI_ALONE : +case DEV_OPMODE_WIFI_ALONE :return "Wi-Fi alone" ; +case DEV_OPMODE_BT_ALONE : +return "BT EDR alone" ; +case DEV_OPMODE_BT_LE_ALONE : +return "BT LE alone" ; +case DEV_OPMODE_BT_DUAL : +return "BT Dual" ; +case DEV_OPMODE_STA_BT : +return "Wi-Fi STA + BT EDR" ; +case DEV_OPMODE_STA_BT_LE : +return "Wi-Fi STA + BT LE" ; +case DEV_OPMODE_STA_BT_DUAL : +return "Wi-Fi STA + BT DUAL" ; +case DEV_OPMODE_AP_BT : +return "Wi-Fi AP + BT EDR" ; +case DEV_OPMODE_AP_BT_DUAL : +return "Wi-Fi AP + BT DUAL" ; }return "Unknown" ;
@@ -267,7 +283,7 @@ void rsi_set_bt_context(void *priv, void *bt_context)* * Return: Pointer to the adapter structure on success, NULL on failure . */ -struct rsi_hw *rsi_91x_init (void ) +struct rsi_hw *rsi_91x_init (u16 oper_mode) {struct rsi_hw *adapter =NULL ;struct rsi_common *common =NULL ;
@@ -309,11 +325,34 @@ struct rsi_hw *rsi_91x_init(void)spin_lock_init (&adapter->ps_lock);timer_setup (&common->roc_timer, rsi_roc_timeout,0 );init_completion (&common->wlan_init_completion); + common->oper_mode = oper_mode; common->init_done = true; - - common->coex_mode =RSI_DEV_COEX_MODE_WIFI_ALONE ; - common->oper_mode =RSI_DEV_OPMODE_WIFI_ALONE ; adapter->device_model =RSI_DEV_9113 ; + +/* Determine coex mode */ +switch (common->oper_mode) { +case DEV_OPMODE_STA_BT_DUAL : +case DEV_OPMODE_STA_BT : +case DEV_OPMODE_STA_BT_LE : +case DEV_OPMODE_BT_ALONE : +case DEV_OPMODE_BT_LE_ALONE : +case DEV_OPMODE_BT_DUAL : + common->coex_mode =2 ; +break ; +case DEV_OPMODE_AP_BT_DUAL : +case DEV_OPMODE_AP_BT : + common->coex_mode =4 ; +break ; +case DEV_OPMODE_WIFI_ALONE : + common->coex_mode =1 ; +break ; +default : + common->oper_mode =1 ; + common->coex_mode =1 ; + } +rsi_dbg (INFO_ZONE ,"%s: oper_mode = %d, coex_mode = %d\n" , + __func__, common->oper_mode, common->coex_mode); +if (common->coex_mode >1 ) {if (rsi_coex_attach (common)) {rsi_dbg (ERR_ZONE ,"Failed to init coex module\n" );
@@ -348,10 +387,12 @@ void rsi_91x_deinit(struct rsi_hw *adapter)for (ii =0 ; ii <NUM_SOFT_QUEUES ; ii++)skb_queue_purge (&common->tx_queue[ii]); - common->init_done = false; - -if (common->coex_mode >1 ) +if (common->coex_mode >1 ) {rsi_coex_detach (common); + rsi_bt_ops.detach (common->bt_adapter); + } + + common->init_done = false;kfree (common);kfree (adapter->rsi_dev);
drivers/net/wireless/rsi/rsi_91x_sdio.c +9 -1
@@ -21,6 +21,14 @@#include "rsi_coex.h" #include "rsi_hal.h" +/* Default operating mode is wlan STA + BT */ +static u16 dev_oper_mode =DEV_OPMODE_STA_BT_DUAL ; +module_param (dev_oper_mode, ushort,0444 ); +MODULE_PARM_DESC (dev_oper_mode, +"1[Wi-Fi], 4[BT], 8[BT LE], 5[Wi-Fi STA + BT classic]\n" +"9[Wi-Fi STA + BT LE], 13[Wi-Fi STA + BT classic + BT LE]\n" +"6[AP + BT classic], 14[AP + BT classic + BT LE]" ); +/** * rsi_sdio_set_cmd52_arg() - This function prepares cmd 52 read/write arg. * @rw: Read/write
@@ -926,7 +934,7 @@ static int rsi_probe(struct sdio_func *pfunction,rsi_dbg (INIT_ZONE ,"%s: Init function called\n" , __func__); - adapter =rsi_91x_init (); + adapter =rsi_91x_init (dev_oper_mode);if (!adapter) {rsi_dbg (ERR_ZONE ,"%s: Failed to init os intf ops\n" , __func__);
drivers/net/wireless/rsi/rsi_91x_usb.c +9 -1
@@ -21,6 +21,14 @@#include "rsi_hal.h" #include "rsi_coex.h" +/* Default operating mode is wlan STA + BT */ +static u16 dev_oper_mode =DEV_OPMODE_STA_BT_DUAL ; +module_param (dev_oper_mode, ushort,0444 ); +MODULE_PARM_DESC (dev_oper_mode, +"1[Wi-Fi], 4[BT], 8[BT LE], 5[Wi-Fi STA + BT classic]\n" +"9[Wi-Fi STA + BT LE], 13[Wi-Fi STA + BT classic + BT LE]\n" +"6[AP + BT classic], 14[AP + BT classic + BT LE]" ); +/** * rsi_usb_card_write() - This function writes to the USB Card. * @adapter: Pointer to the adapter structure.
@@ -708,7 +716,7 @@ static int rsi_probe(struct usb_interface *pfunction,rsi_dbg (INIT_ZONE ,"%s: Init function called\n" , __func__); - adapter =rsi_91x_init (); + adapter =rsi_91x_init (dev_oper_mode);if (!adapter) {rsi_dbg (ERR_ZONE ,"%s: Failed to init os intf ops\n" , __func__);
drivers/net/wireless/rsi/rsi_common.h +1 -1
@@ -81,7 +81,7 @@ static inline int rsi_kill_thread(struct rsi_thread *handle)void rsi_mac80211_detach (struct rsi_hw *hw);u16 rsi_get_connected_channel (struct ieee80211_vif *vif); -struct rsi_hw *rsi_91x_init (void ); +struct rsi_hw *rsi_91x_init (u16 oper_mode);void rsi_91x_deinit (struct rsi_hw *adapter);int rsi_read_pkt (struct rsi_common *common,u8 *rx_pkt,s32 rcv_pkt_len);#ifdef CONFIG_PM
drivers/net/wireless/rsi/rsi_hal.h +11 -0
@@ -17,6 +17,17 @@#ifndef __RSI_HAL_H__#define __RSI_HAL_H__ +/* Device Operating modes */ +#define DEV_OPMODE_WIFI_ALONE 1 +#define DEV_OPMODE_BT_ALONE 4 +#define DEV_OPMODE_BT_LE_ALONE 8 +#define DEV_OPMODE_BT_DUAL 12 +#define DEV_OPMODE_STA_BT 5 +#define DEV_OPMODE_STA_BT_LE 9 +#define DEV_OPMODE_STA_BT_DUAL 13 +#define DEV_OPMODE_AP_BT 6 +#define DEV_OPMODE_AP_BT_DUAL 14 +#define FLASH_WRITE_CHUNK_SIZE (4 * 1024)#define FLASH_SECTOR_SIZE (4 * 1024)
Signature · 1 line
2.7.4
PATCH v3 8/8 rsi: sdio changes to support BT
In reply to Amitkumar KarwarFrom: Prameela Rani Garnepudi <[email protected]>
Queue number is correctly updated for BT traffic. Also, kzalloc instead of kmalloc is used for Rx packet allocation.
--- drivers/net/wireless/rsi/rsi_91x_sdio.c | 2 ++ drivers/net/wireless/rsi/rsi_91x_sdio_ops.c | 2 +- 2 files changed, 3 insertions(+), 1 deletion(-)
drivers/net/wireless/rsi/rsi_91x_sdio.c +2 -0
@@ -763,6 +763,8 @@ static int rsi_sdio_host_intf_write_pkt(struct rsi_hw *adapter,int status; queueno = ((pkt[1 ] >>4 ) &0xf ); +if (queueno ==RSI_BT_MGMT_Q || queueno ==RSI_BT_DATA_Q ) + queueno =RSI_BT_Q ; num_blocks = len / block_size;
drivers/net/wireless/rsi/rsi_91x_sdio_ops.c +1 -1
@@ -103,7 +103,7 @@ static int rsi_process_pkt(struct rsi_common *common) rcv_pkt_len = (num_blks *256 ); - common->rx_data_pkt =kmalloc (rcv_pkt_len,GFP_KERNEL ); + common->rx_data_pkt =kzalloc (rcv_pkt_len,GFP_KERNEL );if (!common->rx_data_pkt) {rsi_dbg (ERR_ZONE ,"%s: Failed in memory allocation\n" , __func__);
Signature · 1 line
2.7.4