ASoC: hdac_hdmi: Ensuring proper setting of output widget power state
PATCH 1/1 ASoC: hdac_hdmi: Ensuring proper setting of output widget power state
From: Abhijeet Kumar <[email protected]>
When we change the resolution of DP pannel or hot plug-unplug it while playing an audio clip,sometimes we observe a silent playback(no audio).
During no audio condition, we have noticed that the power state of the pin or the connector is D3. Optimzing the way we set the power could mitigate the issue.With this changes the verb is sent to set the power state and response is received. Thus ensuring power state is set.
--- sound/soc/codecs/hdac_hdmi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/codecs/hdac_hdmi.c +1 -1
@@ -718,7 +718,7 @@ static void hdac_hdmi_set_power_state(struct hdac_ext_device *edev, {if (get_wcaps (&edev->hdac, nid) &AC_WCAP_POWER ) {if (!snd_hdac_check_power_state (&edev->hdac, nid, pwr_state)) -snd_hdac_codec_write (&edev->hdac, nid,0 , +snd_hdac_codec_read (&edev->hdac, nid,0 ,AC_VERB_SET_POWER_STATE , pwr_state); } }
Signature · 1 line
1.9.1
Quoted 4 lines · On Thu, Jan 11, 2018 at 05:04:27PM +0530, [email protected] wrote:
From: Abhijeet Kumar <[email protected]>
When we change the resolution of DP pannel or hot plug-unplug it while playing an audio clip,sometimes we observe a silent playback(no audio).
can you rephrase this please
Quoted 3 lines
During no audio condition, we have noticed that the power state of the pin or the connector is D3. Optimzing the way we set the power could mitigate the issue.With this changes the verb is sent to set the power
space after .
Quoted 1 line
state and response is received. Thus ensuring power state is set.
am not sure I fully understood the problem here
Quoted 11 lines
Signed-off-by Abhijeet Kumar <[email protected]>--- sound/soc/codecs/hdac_hdmi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)sound/soc/codecs/hdac_hdmi.c +0
-0
sound/soc/codecs/hdac_hdmi.c static void hdac_hdmi_set_power_state(struct hdac_ext_device *edev, · line 721
Quoted 5 lines
sound/soc/codecs/hdac_hdmi.c +1
-1@@ -718,7 +718,7 @@ static void hdac_hdmi_set_power_state(struct hdac_ext_device *edev, {if (get_wcaps (&edev->hdac, nid) &AC_WCAP_POWER ) {if (!snd_hdac_check_power_state (&edev->hdac, nid, pwr_state)) - snd_hdac_codec_write(&edev->hdac, nid, 0, + snd_hdac_codec_read(&edev->hdac, nid, 0,
how does read help instead of write?
Signature · 1 line
~Vinod
Quoted 6 lines · Vinod Koul
Quoted 4 lines · On Thu, Jan 11, 2018 at 05:04:27PM +0530, [email protected] wrote:
From: Abhijeet Kumar <[email protected]>
When we change the resolution of DP pannel or hot plug-unplug it while playing an audio clip,sometimes we observe a silent playback(no audio).
can you rephrase this please
done please review v2!
Quoted 7 lines
Quoted 3 lines
During no audio condition, we have noticed that the power state of the pin or the connector is D3. Optimzing the way we set the power could mitigate the issue.With this changes the verb is sent to set the power
space after .
Quoted 1 line
state and response is received. Thus ensuring power state is set.
am not sure I fully understood the problem here
This appears to be an timing issue, while performing a stress test, we found out that sometimes either pin or converters are not powered up. Thus ensuring it that the power state is set correctly.
Quoted 6 lines
Quoted 6 lines
Signed-off-by Abhijeet Kumar <[email protected]>--- sound/soc/codecs/hdac_hdmi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
Quoted 11 lines
sound/soc/codecs/hdac_hdmi.c static void hdac_hdmi_set_power_state(struct hdac_ext_device *edev, · line 721
Quoted 10 lines
sound/soc/codecs/hdac_hdmi.c +1
-1@@ -718,7 +718,7 @@ static void hdac_hdmi_set_power_state(struct hdac_ext_device *edev, {if (get_wcaps (&edev->hdac, nid) &AC_WCAP_POWER ) {if (!snd_hdac_check_power_state (&edev->hdac, nid, pwr_state)) - snd_hdac_codec_write(&edev->hdac, nid, 0, + snd_hdac_codec_read(&edev->hdac, nid, 0,how does read help instead of write?
Indeed i'm making use of read instead of write to send the set command.
But unlike codec_write, codec_read send the verb synchronously. Maybe if you read the comment while powering up and down in hdmi_codec_prepare and hdmi_codec_complete you would understand better.
"codec_read is preferred over codec_write to set the power state.
This way verb is send to set the power state and response is received. So setting power state is ensured without using loop to read the state."
Quoted 1 line
Quoted 48 lines · Abhijeet
Quoted 6 lines · Vinod Koul
Quoted 4 lines · On Thu, Jan 11, 2018 at 05:04:27PM +0530, [email protected] wrote:
From: Abhijeet Kumar <[email protected]>
When we change the resolution of DP pannel or hot plug-unplug it while playing an audio clip,sometimes we observe a silent playback(no audio).
can you rephrase this please
done please review v2!
Quoted 7 lines
Quoted 3 lines
During no audio condition, we have noticed that the power state of the pin or the connector is D3. Optimzing the way we set the power could mitigate the issue.With this changes the verb is sent to set the power
space after .
Quoted 1 line
state and response is received. Thus ensuring power state is set.
am not sure I fully understood the problem here
This appears to be an timing issue, while performing a stress test, we found out that sometimes either pin or converters are not powered up. Thus ensuring it that the power state is set correctly.
Quoted 6 lines
Quoted 6 lines
Signed-off-by Abhijeet Kumar <[email protected]>--- sound/soc/codecs/hdac_hdmi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)Quoted 11 lines
sound/soc/codecs/hdac_hdmi.c static void hdac_hdmi_set_power_state(struct hdac_ext_device *edev, · line 721
Quoted 10 lines
sound/soc/codecs/hdac_hdmi.c +1
-1@@ -718,7 +718,7 @@ static void hdac_hdmi_set_power_state(struct hdac_ext_device *edev, {if (get_wcaps (&edev->hdac, nid) &AC_WCAP_POWER ) {if (!snd_hdac_check_power_state (&edev->hdac, nid, pwr_state)) - snd_hdac_codec_write(&edev->hdac, nid, 0, + snd_hdac_codec_read(&edev->hdac, nid, 0,how does read help instead of write?
Indeed i'm making use of read instead of write to send the set command.
But unlike
codec_write,codec_readsend the verb synchronously. Maybe if you read the comment while powering up and down inhdmi_codec_prepareandhdmi_codec_completeyou would understand better.
Quoted 5 lines
"
codec_readis preferred overcodec_writeto set the power state.This way verb is send to set the power state and response is received. So setting power state is ensured without using loop to read the state."
It's better, but doesn't guarantee that the node reached the given power state. codec_read assures that the verb is sent and the codec gives the response. But it means only the target state gets updated, and doesn't mean that the actual state reached.
thanks,
Takashi
Quoted 1 line
It's better, but doesn't guarantee that the node reached the given power state.
codec_readassures that the verb is sent and the codec gives the response. But it means only the target state gets updated, and doesn't mean that the actual state reached.
Thanks Takashi for replying. I guess, I should make use of return value from codec_read and retry if power state is not set properly! I'll make those changes and update again. And just wondering, how does hdmi_codec_prepare() and hdmi_codec_complete() gurantee while powering up and down the afg ?
Warm Regards,
Abhijeet
Quoted 4 lines · Abhijeet
Quoted 2 lines
It's better, but doesn't guarantee that the node reached the given power state.
codec_readassures that the verb is sent and the codec gives the response. But it means only the target state gets updated, and doesn't mean that the actual state reached.Thanks Takashi for replying. I guess, I should make use of return value from
codec_readand retry if power state is not set properly! I'll make those changes and update again. And just wondering, how doeshdmi_codec_prepare()andhdmi_codec_complete()gurantee while powering up and down the afg ?
There are two power states in the codec node: the target and the actual. By setting the power state, the target is set, but the actual state change may still take some time. In such a case, you'd need to wait until the actual state reaches. See hda_sync_power_state() in the hda legacy.
Takashi
Quoted 1 line
can you rephrase this please
done please review v2! https://patchwork.kernel.org/patch/10159791/
Quoted 1 line
am not sure I fully understood the problem here
This appears to be an timing issue, while performing a stress test, we found out that sometimes either pin or converters are not powered up. Thus ensuring it that the power state is set correctly.
Quoted 1 line
how does read help instead of write?
Indeed i'm making use of read instead of write to send the set command. But unlike codec_write, codec_read send the verb synchronously. Maybe if you read the comment while powering up and down afg in hdmi_codec_prepare and hdmi_codec_complete you would understand better. "codec_read is preferred over codec_write to set the power state. This way verb is send to set the power state and response is received. So setting power state is ensured without using loop to read the state."
-----Original Message-----
From: Koul, Vinod
Sent: Friday, January 12, 2018 11:17 AM
To: Kumar, Abhijeet <[email protected]>
Cc: Liam Girdwood <[email protected]>; Mark Brown <[email protected]>; Jaroslav Kysela <[email protected]>; Takashi Iwai <[email protected]>; Kp, Jeeja <[email protected]>; Prusty, Subhransu S <[email protected]>; Singh, Guneshwor O <[email protected]>; Tayal, SandeepX <[email protected]>; [email protected]; [email protected]
Subject: Re: [PATCH] ASoC: hdac_hdmi: Ensuring proper setting of output widget power state
Quoted 4 lines · On Thu, Jan 11, 2018 at 05:04:27PM +0530, [email protected] wrote:
From: Abhijeet Kumar <[email protected]>
When we change the resolution of DP pannel or hot plug-unplug it while playing an audio clip,sometimes we observe a silent playback(no audio).
can you rephrase this please
Quoted 3 lines
During no audio condition, we have noticed that the power state of the pin or the connector is D3. Optimzing the way we set the power could mitigate the issue.With this changes the verb is sent to set the power
space after .
Quoted 1 line
state and response is received. Thus ensuring power state is set.
am not sure I fully understood the problem here
Quoted 11 lines
Signed-off-by Abhijeet Kumar <[email protected]>--- sound/soc/codecs/hdac_hdmi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)(quoted diff) +0
-0
b/sound/soc/codecs/hdac_hdmi.cindexf3b4f4dfae6a..e24caecf0a4f100644
sound/soc/codecs/hdac_hdmi.c static void hdac_hdmi_set_power_state(struct · line 721
Quoted 5 lines
sound/soc/codecs/hdac_hdmi.c +1
-1@@ -718,7 +718,7 @@ static void hdac_hdmi_set_power_state(struct hdac_ext_device *edev, {if (get_wcaps (&edev->hdac, nid) &AC_WCAP_POWER ) {if (!snd_hdac_check_power_state (&edev->hdac, nid, pwr_state)) - snd_hdac_codec_write(&edev->hdac, nid, 0, + snd_hdac_codec_read(&edev->hdac, nid, 0,
how does read help instead of write?
--
~Vinod
PATCH v2 1/1 ASoC: hdac_hdmi: Ensuring proper setting of output widget power state
In reply to [email protected]From: Abhijeet Kumar <[email protected]>
In usecases like hot plug-unplug DP panel or modeset during a playback, sometimes we observe no audio after codec resets.
During no audio condition, we have noticed that the power state of the pin or the connector is D3. Optimzing the way we set the power could mitigate the issue. With this changes the verb is sent to set the power state and response is received. Thus ensuring power state is set.
---
Changes in v2:
- update commit message
sound/soc/codecs/hdac_hdmi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/codecs/hdac_hdmi.c +1 -1
@@ -718,7 +718,7 @@ static void hdac_hdmi_set_power_state(struct hdac_ext_device *edev, {if (get_wcaps (&edev->hdac, nid) &AC_WCAP_POWER ) {if (!snd_hdac_check_power_state (&edev->hdac, nid, pwr_state)) -snd_hdac_codec_write (&edev->hdac, nid,0 , +snd_hdac_codec_read (&edev->hdac, nid,0 ,AC_VERB_SET_POWER_STATE , pwr_state); } }
Signature · 1 line
1.9.1
Mark Brown
maintainerApplied "ASoC: hdac_hdmi: Ensuring proper setting of output widget power state" to the asoc tree
In reply to [email protected]The patch
ASoC: hdac_hdmi: Ensuring proper setting of output widget power state
has been applied to the asoc tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark
Quoted 1 line
From
a04ba2b3dc6c14bedd5efca442d6039690562951Mon Sep 17 00:00:00 2001
From: Abhijeet Kumar <[email protected]>
Date: Fri, 12 Jan 2018 14:02:54 +0530
Subject: [PATCH] ASoC: hdac_hdmi: Ensuring proper setting of output widget
power state
In usecases like hot plug-unplug DP panel or modeset during a playback, sometimes we observe no audio after codec resets.
During no audio condition, we have noticed that the power state of the pin or the connector is D3. Optimzing the way we set the power could mitigate the issue. With this changes the verb is sent to set the power state and response is received. Thus ensuring power state is set.
--- sound/soc/codecs/hdac_hdmi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/codecs/hdac_hdmi.c +1 -1
@@ -718,7 +718,7 @@ static void hdac_hdmi_set_power_state(struct hdac_ext_device *edev, {if (get_wcaps (&edev->hdac, nid) &AC_WCAP_POWER ) {if (!snd_hdac_check_power_state (&edev->hdac, nid, pwr_state)) -snd_hdac_codec_write (&edev->hdac, nid,0 , +snd_hdac_codec_read (&edev->hdac, nid,0 ,AC_VERB_SET_POWER_STATE , pwr_state); } }
Signature · 1 line
2.15.1
Mark Brown
maintainerRe: Applied "ASoC: hdac_hdmi: Ensuring proper setting of output widget power state" to the asoc tree
Quoted 7 lines · Mark Brown
The patch
ASoC:
hdac_hdmi: Ensuring proper setting of output widget power statehas been applied to the asoc tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
I've dropped this because it caused a conflict with the topic/hdac-hdmi branch - can you please check what's going on there? I merged that into the topic/intel branch so probably just a rebase is needed.
RE: Applied "ASoC: hdac_hdmi: Ensuring proper setting of output widget power state" to the asoc tree
Quoted 1 line
I've dropped this because it caused a conflict with the topic/hdac-hdmi branch - can you please check what's going on there?
I'm working on inputs from Takashi and Pierre. After much of testing I'll share the revision patch which waits until actual state reaches target state (similar is implemented in hda) by ww03.
Warm Regards,
Abhijeet
-----Original Message-----
From: Mark Brown [mailto:[email protected]]
Sent: Saturday, January 13, 2018 2:50 AM
To: Kumar, Abhijeet <[email protected]>
Cc: Liam Girdwood <[email protected]>; Jaroslav Kysela <[email protected]>; Takashi Iwai <[email protected]>; Kp, Jeeja <[email protected]>; Koul, Vinod <[email protected]>; Prusty, Subhransu S <[email protected]>; Singh, Guneshwor O <[email protected]>; Tayal, SandeepX <[email protected]>; [email protected]; [email protected]
Subject: Re: Applied "ASoC: hdac_hdmi: Ensuring proper setting of output widget power state" to the asoc tree
Quoted 8 lines · Mark Brown
The patch
ASoC:
hdac_hdmi: Ensuring proper setting of output widget power
statehas been applied to the asoc tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
I've dropped this because it caused a conflict with the topic/hdac-hdmi branch - can you please check what's going on there? I merged that into the topic/intel branch so probably just a rebase is needed.
Re: Applied "ASoC: hdac_hdmi: Ensuring proper setting of output widget power state" to the asoc tree
In reply to Mark BrownQuoted 5 lines · Mark Brown
Quoted 4 lines · Mark Brown
The patch
ASoC:
hdac_hdmi: Ensuring proper setting of output widget power state
Quoted 7 lines
Quoted 3 lines
has been applied to the asoc tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
I've dropped this because it caused a conflict with the topic/hdac-hdmi branch - can you please check what's going on there? I merged that into the topic/intel branch so probably just a rebase is needed.
Hey Mark,
I do not think this is ready yet. Takashi and me have few comments on this...
Signature · 1 line
~Vinod
Mark Brown
maintainerRe: Applied "ASoC: hdac_hdmi: Ensuring proper setting of output widget power state" to the asoc tree
Quoted 8 lines · Vinod Koul
Quoted 3 lines · Mark Brown
I've dropped this because it caused a conflict with the topic/hdac-hdmi branch - can you please check what's going on there? I merged that into the topic/intel branch so probably just a rebase is needed.
I do not think this is ready yet. Takashi and me have few comments on this...
There were comments on v1 but nobody responded to v2.
Re: Applied "ASoC: hdac_hdmi: Ensuring proper setting of output widget power state" to the asoc tree
Quoted 11 lines · Mark Brown
Quoted 8 lines · Vinod Koul
Quoted 3 lines · Mark Brown
I've dropped this because it caused a conflict with the topic/hdac-hdmi branch - can you please check what's going on there? I merged that into the topic/intel branch so probably just a rebase is needed.
I do not think this is ready yet. Takashi and me have few comments on this...
There were comments on v1 but nobody responded to v2.
yeah we were still stuck on v1 :) I think Abhijeet will post an update once we align..
Signature · 1 line
~Vinod
Re: Applied "ASoC: hdac_hdmi: Ensuring proper setting of output widget power state" to the asoc tree
Quoted 11 lines · Vinod Koul
Quoted 8 lines · Mark Brown
Quoted 6 lines · Vinod Koul
Quoted 3 lines · Mark Brown
I've dropped this because it caused a conflict with the topic/hdac-hdmi branch - can you please check what's going on there? I merged that into the topic/intel branch so probably just a rebase is needed.
I do not think this is ready yet. Takashi and me have few comments on this...
There were comments on v1 but nobody responded to v2.
yeah we were still stuck on v1 :) I think Abhijeet will post an update once we align..
Hi, I 've posted the latest series on ALSAdev mailing list. Kindly review. :)
https://patchwork.kernel.org/patch/10180821/
https://patchwork.kernel.org/patch/10180825/
https://patchwork.kernel.org/patch/10180827/
Quoted 1 line
PATCH 1/3 ALSA: hda: Copying sync power state helper to core
In reply to [email protected]From: Abhijeet Kumar <[email protected]>
The current sync_power_state is local to hda code, moving it core so that other users apart from hda legacy can use it. The helper function ensures the actual state reaches the target state.
--- include/sound/hdaudio.h | 2 ++ sound/hda/hdac_device.c | 35 +++++++++++++++++++++++++++++++++++ 2 files changed, 37 insertions(+)
include/sound/hdaudio.h +2 -0
@@ -146,6 +146,8 @@ int snd_hdac_codec_write(struct hdac_device *hdac, hda_nid_t nid, int flags, unsigned int verb, unsigned int parm);bool snd_hdac_check_power_state (struct hdac_device *hdac,hda_nid_t nid,unsigned int target_state); +unsigned int snd_hdac_sync_power_state (struct hdac_device *hdac, +hda_nid_t nid,unsigned int target_state);/** * snd_hdac_read_parm - read a codec parameter * @codec: the codec object
sound/hda/hdac_device.c +35 -0
@@ -3,6 +3,7 @@*/ #include <linux/init.h> +#include <linux/delay.h> #include <linux/device.h> #include <linux/slab.h> #include <linux/module.h>
@@ -1064,3 +1065,37 @@ bool snd_hdac_check_power_state(struct hdac_device *hdac,return (state == target_state); }EXPORT_SYMBOL_GPL (snd_hdac_check_power_state); +/** +* snd_hdac_sync_power_state - wait until actual power state matches +* with the target state +* +* @hdac: the HDAC device +* @nid: NID to send the command +* @target_state: target state to check for +* +* Return power state or PS_ERROR if codec rejects GET verb. +*/ +unsigned int snd_hdac_sync_power_state (struct hdac_device *codec, +hda_nid_t nid,unsigned int power_state) +{ +unsigned long end_time = jiffies +msecs_to_jiffies (500 ); +unsigned int state, actual_state, count; + +for (count =0 ; count <500 ; count++) { + state =snd_hdac_codec_read (codec, nid,0 , +AC_VERB_GET_POWER_STATE ,0 ); +if (state &AC_PWRST_ERROR ) { +msleep (20 ); +break ; + } + actual_state = (state >>4 ) &0x0f ; +if (actual_state == power_state) +break ; +if (time_after_eq (jiffies, end_time)) +break ; +/* wait until the codec reachs to the target state */ +msleep (1 ); + } +return state; +} +EXPORT_SYMBOL_GPL (snd_hdac_sync_power_state);
Signature · 1 line
1.9.1
PATCH 2/3 ALSA: hda: Make use of core codec functions to sync power state
From: Abhijeet Kumar <[email protected]>
Since sync_power_state is moved to core it's better to use the helper function to ensure the actual power state reaches target instead of using the local helper functions already exsisting in hda code.
--- sound/pci/hda/hda_codec.c | 28 +--------------------------- sound/pci/hda/hda_local.h | 6 +++++- 2 files changed, 6 insertions(+), 28 deletions(-)
sound/pci/hda/hda_codec.c +1 -27
@@ -2702,32 +2702,6 @@ void snd_hda_codec_set_power_to_all(struct hda_codec *codec, hda_nid_t fg, }EXPORT_SYMBOL_GPL (snd_hda_codec_set_power_to_all); -/* -* wait until the state is reached, returns the current state -*/ -static unsigned int hda_sync_power_state (struct hda_codec *codec, -hda_nid_t fg, -unsigned int power_state) -{ -unsigned long end_time = jiffies +msecs_to_jiffies (500 ); -unsigned int state, actual_state; - -for (;;) { - state =snd_hda_codec_read (codec, fg,0 , -AC_VERB_GET_POWER_STATE ,0 ); -if (state &AC_PWRST_ERROR ) -break ; - actual_state = (state >>4 ) &0x0f ; -if (actual_state == power_state) -break ; -if (time_after_eq (jiffies, end_time)) -break ; -/* wait until the codec reachs to the target state */ -msleep (1 ); - } -return state; -} -/** * snd_hda_codec_eapd_power_filter - A power filter callback for EAPD * @codec: the HDA codec
@@ -2790,7 +2764,7 @@ static unsigned int hda_set_power_state(struct hda_codec *codec, state);snd_hda_codec_set_power_to_all (codec, fg, power_state); } - state =hda_sync_power_state (codec, fg, power_state); + state =snd_hda_sync_power_state (codec, fg, power_state);if (!(state &AC_PWRST_ERROR ))break ; }
sound/pci/hda/hda_local.h +5 -1
@@ -622,7 +622,11 @@ int snd_hda_check_amp_list_power(struct hda_codec *codec, {return snd_hdac_check_power_state (&codec->core, nid, target_state); } - +static inline bool snd_hda_sync_power_state (struct hda_codec *codec, +hda_nid_t nid,unsigned int target_state) +{ +return snd_hdac_sync_power_state (&codec->core, nid, target_state); +}unsigned int snd_hda_codec_eapd_power_filter (struct hda_codec *codec,hda_nid_t nid,unsigned int power_state);
Signature · 1 line
1.9.1
PATCH 3/3 ASoC: hdac_hdmi : Ensuring proper setting of output widget power state
In reply to [email protected]From: Abhijeet Kumar <[email protected]>
In usecases like hot plug-unplug DP panel or modeset during a playback, sometimes we observe no audio after codec resets. During no audio condition, we have noticed that the power state of the pin or the connector is D3. Optimizing the way we set the power mitigates the issue. With this changes the verb is sent to set the power state and waits until actual state reaches target state. Thus ensuring power state is set.
--- sound/soc/codecs/hdac_hdmi.c | 16 +++++++++++++--- 1 file changed, 13 insertions(+), 3 deletions(-)
sound/soc/codecs/hdac_hdmi.c +13 -3
@@ -716,10 +716,20 @@ static struct hdac_hdmi_pcm *hdac_hdmi_get_pcm(struct hdac_ext_device *edev,static void hdac_hdmi_set_power_state (struct hdac_ext_device *edev,hda_nid_t nid,unsigned int pwr_state) { +int count; +unsigned int state;if (get_wcaps (&edev->hdac, nid) &AC_WCAP_POWER ) { -if (!snd_hdac_check_power_state (&edev->hdac, nid, pwr_state)) -snd_hdac_codec_write (&edev->hdac, nid,0 , -AC_VERB_SET_POWER_STATE , pwr_state); +if (!snd_hdac_check_power_state (&edev->hdac, nid, pwr_state)) { +for (count =0 ; count <10 ; count++) { +snd_hdac_codec_read (&edev->hdac, nid,0 , +AC_VERB_SET_POWER_STATE , + pwr_state); + state =snd_hdac_sync_power_state (&edev->hdac, + nid, pwr_state); +if (!(state &AC_PWRST_ERROR )) +break ; + } + } } }
Signature · 1 line
1.9.1
Takashi Iwai
AppliedRe: [PATCH 3/3] ASoC: hdac_hdmi : Ensuring proper setting of output widget power state
Quoted 11 lines · On Tue, 23 Jan 2018 18:30:53 +0100, <[email protected]> wrote:
From: Abhijeet Kumar <[email protected]>
In usecases like hot plug-unplug DP panel or modeset during a playback, sometimes we observe no audio after codec resets. During no audio condition, we have noticed that the power state of the pin or the connector is D3. Optimizing the way we set the power mitigates the issue. With this changes the verb is sent to set the power state and waits until actual state reaches target state. Thus ensuring power state is set.
Quoted 1 line
Signed-off-by Abhijeet Kumar <[email protected]>
I applied the patches 1 and 2 to topic/hda-sync-power branch. It's based on 4.16-rc1.
Mark, could you pull that into your intel branch and apply this fix?
thanks,
Takashi
Quoted 36 lines
--- sound/soc/codecs/hdac_hdmi.c | 16 +++++++++++++--- 1 file changed, 13 insertions(+), 3 deletions(-)sound/soc/codecs/hdac_hdmi.c +13
-3@@ -716,10 +716,20 @@ static struct hdac_hdmi_pcm *hdac_hdmi_get_pcm(struct hdac_ext_device *edev,static void hdac_hdmi_set_power_state (struct hdac_ext_device *edev,hda_nid_t nid,unsigned int pwr_state) { +int count; +unsigned int state;if (get_wcaps (&edev->hdac, nid) &AC_WCAP_POWER ) { -if (!snd_hdac_check_power_state (&edev->hdac, nid, pwr_state)) -snd_hdac_codec_write (&edev->hdac, nid,0 , -AC_VERB_SET_POWER_STATE , pwr_state); +if (!snd_hdac_check_power_state (&edev->hdac, nid, pwr_state)) { +for (count =0 ; count <10 ; count++) { +snd_hdac_codec_read (&edev->hdac, nid,0 , +AC_VERB_SET_POWER_STATE , + pwr_state); + state =snd_hdac_sync_power_state (&edev->hdac, + nid, pwr_state); +if (!(state &AC_PWRST_ERROR )) +break ; + } + } } }Signature · 1 line
1.9.1
Mark Brown
maintainerRe: [PATCH 3/3] ASoC: hdac_hdmi : Ensuring proper setting of output widget power state
In reply to [email protected]Quoted 9 lines · On Tue, Jan 23, 2018 at 11:00:53PM +0530, [email protected] wrote:
From: Abhijeet Kumar <[email protected]>
In usecases like hot plug-unplug DP panel or modeset during a playback, sometimes we observe no audio after codec resets. During no audio condition, we have noticed that the power state of the pin or the connector is D3. Optimizing the way we set the power mitigates the issue. With this changes the verb is sent to set the power state and waits until actual state reaches target state. Thus ensuring power state is set.
This doesn't apply after the recent refactoring to move to components - can you please rebase on current code and resend? I pulled Takashi's branch already, it's just this patch needs handling.
Re: [PATCH 3/3] ASoC: hdac_hdmi : Ensuring proper setting of output widget power state
Quoted 10 lines · Mark Brown
Quoted 9 lines · On Tue, Jan 23, 2018 at 11:00:53PM +0530, [email protected] wrote:
From: Abhijeet Kumar <[email protected]>
In usecases like hot plug-unplug DP panel or modeset during a playback, sometimes we observe no audio after codec resets. During no audio condition, we have noticed that the power state of the pin or the connector is D3. Optimizing the way we set the power mitigates the issue. With this changes the verb is sent to set the power state and waits until actual state reaches target state. Thus ensuring power state is set.
Quoted 3 lines
This doesn't apply after the recent refactoring to move to components - can you please rebase on current code and resend? I pulled Takashi's branch already, it's just this patch needs handling.
Please find the re-based patch here.
https://patchwork.kernel.org/patch/10220549/
Warm Regards,
Abhijeet
PATCH 1/1 ASoC: hdac_hdmi : Ensuring proper setting of output widget power state
In reply to [email protected]From: Abhijeet Kumar <[email protected]>
In usecases like hot plug-unplug DP panel or modeset during a playback, sometimes we observe no audio after codec resets. During no audio condition, we have noticed that the power state of the pin or the connector is D3. Optimizing the way we set the power mitigates the issue. With this changes the verb is sent to set the power state and waits until actual state reaches target state. Thus ensuring power state is set.
--- sound/soc/codecs/hdac_hdmi.c | 18 +++++++++++++++--- 1 file changed, 15 insertions(+), 3 deletions(-)
sound/soc/codecs/hdac_hdmi.c +15 -3
@@ -718,10 +718,22 @@ static struct hdac_hdmi_pcm *hdac_hdmi_get_pcm(struct hdac_ext_device *edev,static void hdac_hdmi_set_power_state (struct hdac_ext_device *edev,hda_nid_t nid,unsigned int pwr_state) { +int count; +unsigned int state; +if (get_wcaps (&edev->hdev, nid) &AC_WCAP_POWER ) { -if (!snd_hdac_check_power_state (&edev->hdev, nid, pwr_state)) -snd_hdac_codec_write (&edev->hdev, nid,0 , -AC_VERB_SET_POWER_STATE , pwr_state); +if (!snd_hdac_check_power_state (&edev->hdac, nid, pwr_state)) { +for (count =0 ; count <10 ; count++) { +snd_hdac_codec_read (&edev->hdac, nid,0 , +AC_VERB_SET_POWER_STATE , + pwr_state); + state =snd_hdac_sync_power_state (&edev->hdac, + nid, pwr_state); +if (!(state &AC_PWRST_ERROR )) +break ; + } + } + } }
Signature · 1 line
1.9.1
Mark Brown
maintainerApplied "ASoC: hdac_hdmi : Ensuring proper setting of output widget power state" to the asoc tree
The patch
ASoC: hdac_hdmi : Ensuring proper setting of output widget power state
has been applied to the asoc tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark
Quoted 1 line
From
753597fbb7031ff147d4f2862426699e4ad8efcaMon Sep 17 00:00:00 2001
From: Abhijeet Kumar <[email protected]>
Date: Thu, 15 Feb 2018 14:05:38 +0530
Subject: [PATCH] ASoC: hdac_hdmi : Ensuring proper setting of output widget
power state
In usecases like hot plug-unplug DP panel or modeset during a playback, sometimes we observe no audio after codec resets. During no audio condition, we have noticed that the power state of the pin or the connector is D3. Optimizing the way we set the power mitigates the issue. With this changes the verb is sent to set the power state and waits until actual state reaches target state. Thus ensuring power state is set.
--- sound/soc/codecs/hdac_hdmi.c | 18 +++++++++++++++--- 1 file changed, 15 insertions(+), 3 deletions(-)
sound/soc/codecs/hdac_hdmi.c +15 -3
@@ -718,10 +718,22 @@ static struct hdac_hdmi_pcm *hdac_hdmi_get_pcm(struct hdac_ext_device *edev,static void hdac_hdmi_set_power_state (struct hdac_ext_device *edev,hda_nid_t nid,unsigned int pwr_state) { +int count; +unsigned int state; +if (get_wcaps (&edev->hdev, nid) &AC_WCAP_POWER ) { -if (!snd_hdac_check_power_state (&edev->hdev, nid, pwr_state)) -snd_hdac_codec_write (&edev->hdev, nid,0 , -AC_VERB_SET_POWER_STATE , pwr_state); +if (!snd_hdac_check_power_state (&edev->hdac, nid, pwr_state)) { +for (count =0 ; count <10 ; count++) { +snd_hdac_codec_read (&edev->hdac, nid,0 , +AC_VERB_SET_POWER_STATE , + pwr_state); + state =snd_hdac_sync_power_state (&edev->hdac, + nid, pwr_state); +if (!(state &AC_PWRST_ERROR )) +break ; + } + } + } }
Signature · 1 line
2.16.1
PATCH v2 1/1 ASoC: hdac_hdmi : Ensuring proper setting of output widget power state
In reply to [email protected]From: Abhijeet Kumar <[email protected]>
In usecases like hot plug-unplug DP panel or modeset during a playback, sometimes we observe no audio after codec resets. During no audio condition, we have noticed that the power state of the pin or the connector is D3. Optimizing the way we set the power mitigates the issue. With this changes the verb is sent to set the power state and waits until actual state reaches target state. Thus ensuring power state is set.
--- sound/soc/codecs/hdac_hdmi.c | 18 +++++++++++++++--- 1 file changed, 15 insertions(+), 3 deletions(-)
sound/soc/codecs/hdac_hdmi.c +15 -3
@@ -718,10 +718,22 @@ static struct hdac_hdmi_pcm *hdac_hdmi_get_pcm(struct hdac_ext_device *edev,static void hdac_hdmi_set_power_state (struct hdac_ext_device *edev,hda_nid_t nid,unsigned int pwr_state) { +int count; +unsigned int state; +if (get_wcaps (&edev->hdev, nid) &AC_WCAP_POWER ) { -if (!snd_hdac_check_power_state (&edev->hdev, nid, pwr_state)) -snd_hdac_codec_write (&edev->hdev, nid,0 , -AC_VERB_SET_POWER_STATE , pwr_state); +if (!snd_hdac_check_power_state (&edev->hdev, nid, pwr_state)) { +for (count =0 ; count <10 ; count++) { +snd_hdac_codec_read (&edev->hdev, nid,0 , +AC_VERB_SET_POWER_STATE , + pwr_state); + state =snd_hdac_sync_power_state (&edev->hdev, + nid, pwr_state); +if (!(state &AC_PWRST_ERROR )) +break ; + } + } + } }
Signature · 1 line
1.9.1