Fix loading of module radeonfb on PowerMac
Subsystems (2)
PATCH v2 1/1 Fix loading of module radeonfb on PowerMac
When the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=m
The offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16
This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.
It should be noticed that offb_destroy is never called which explain the need to skip error detection on the radeon side.
--- drivers/video/fbdev/aty/radeon_base.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)
drivers/video/fbdev/aty/radeon_base.c +26 -0
@@ -2259,6 +2259,22 @@ static struct bin_attribute edid2_attr = { .read = radeon_show_edid2, }; +static int radeon_kick_out_firmware_fb (struct pci_dev *pdev) +{ +struct apertures_struct *ap; + + ap =alloc_apertures (1 ); +if (!ap) +return -ENOMEM ; + + ap->ranges[0 ].base =pci_resource_start (pdev,0 ); + ap->ranges[0 ].size =pci_resource_len (pdev,0 ); + +remove_conflicting_framebuffers (ap,KBUILD_MODNAME , false); +kfree (ap); + +return 0 ; +}static int radeonfb_pci_register (struct pci_dev *pdev,const struct pci_device_id *ent)
@@ -2314,19 +2330,27 @@ static int radeonfb_pci_register(struct pci_dev *pdev, rinfo->fb_base_phys =pci_resource_start (pdev,0 ); rinfo->mmio_base_phys =pci_resource_start (pdev,2 ); + ret =radeon_kick_out_firmware_fb (pdev); +if (ret) +return ret; +/* request the mem regions */ ret =pci_request_region (pdev,0 ,"radeonfb framebuffer" );if (ret <0 ) {printk (KERN_ERR "radeonfb (%s): cannot request region 0.\n" ,pci_name (rinfo->pdev)); +#ifndef CONFIG_PPC goto err_release_fb; +#endif } ret =pci_request_region (pdev,2 ,"radeonfb mmio" );if (ret <0 ) {printk (KERN_ERR "radeonfb (%s): cannot request region 2.\n" ,pci_name (rinfo->pdev)); +#ifndef CONFIG_PPC goto err_release_pci0; +#endif }/* map the regions */
@@ -2511,10 +2535,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,iounmap (rinfo->mmio_base); err_release_pci2:pci_release_region (pdev,2 ); +#ifndef CONFIG_PPC err_release_pci0:pci_release_region (pdev,0 ); err_release_fb:framebuffer_release (info); +#endif err_disable: err_out:return ret;
Signature · 1 line
2.1.4
Hi,
Quoted 18 lines · Mathieu Malaterre
When the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=mThe offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.
Quoted 8 lines
It should be noticed that
offb_destroyis never called which explain the need to skip error detection on the radeon side.Signed-off-by Mathieu Malaterre <[email protected]>Suggested-by Lennart Sorensen <[email protected]>---
Please always have a changelog in patch new revisions. For individual patches, you can insert the changes here.
Quoted 36 lines
drivers/video/fbdev/aty/radeon_base.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)drivers/video/fbdev/aty/radeon_base.c +18
-0@@ -2259,6 +2259,22 @@ static struct bin_attribute edid2_attr = { .read = radeon_show_edid2, }; +static int radeon_kick_out_firmware_fb (struct pci_dev *pdev) +{ +struct apertures_struct *ap; + + ap =alloc_apertures (1 ); +if (!ap) +return -ENOMEM ; + + ap->ranges[0 ].base =pci_resource_start (pdev,0 ); + ap->ranges[0 ].size =pci_resource_len (pdev,0 ); + +remove_conflicting_framebuffers (ap,KBUILD_MODNAME , false); +kfree (ap); + +return 0 ; +}static int radeonfb_pci_register (struct pci_dev *pdev,const struct pci_device_id *ent)@@ -2314,19 +2330,27 @@ static int radeonfb_pci_register(struct pci_dev *pdev, rinfo->fb_base_phys =pci_resource_start (pdev,0 ); rinfo->mmio_base_phys =pci_resource_start (pdev,2 ); + ret =radeon_kick_out_firmware_fb (pdev); +if (ret)
drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2344
Quoted 10 lines
drivers/video/fbdev/aty/radeon_base.c +4
-0+return ret; +/* request the mem regions */ ret =pci_request_region (pdev,0 ,"radeonfb framebuffer" );if (ret <0 ) {printk (KERN_ERR "radeonfb (%s): cannot request region 0.\n" ,pci_name (rinfo->pdev)); +#ifndef CONFIG_PPC goto err_release_fb; +#endif
If this is not a problem on PPC, the kernel shouldn't print an error either.
drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2353
Quoted 9 lines
drivers/video/fbdev/aty/radeon_base.c +2
-0} ret =pci_request_region (pdev,2 ,"radeonfb mmio" );if (ret <0 ) {printk (KERN_ERR "radeonfb (%s): cannot request region 2.\n" ,pci_name (rinfo->pdev)); +#ifndef CONFIG_PPC goto err_release_pci0; +#endif
Same here.
Quoted 7 lines
drivers/video/fbdev/aty/radeon_base.c +0
-0}/* map the regions */ @@ -2511,10 +2535,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,iounmap (rinfo->mmio_base); err_release_pci2:
drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2546
Quoted 10 lines
drivers/video/fbdev/aty/radeon_base.c +2
-0pci_release_region (pdev,2 ); +#ifndef CONFIG_PPC err_release_pci0:pci_release_region (pdev,0 ); err_release_fb:framebuffer_release (info); +#endif err_disable: err_out:return ret;
So I don't quite follow what's going on here. Why the CONFIG_PPC conditionals? Is this problem only with OFFB and only with PPC?
And I think the code itself should have comments on this rather strange
behavior: the driver fails to get HW resources, but decides to ignore the failure on PPC.
Tomi
Quoted 106 lines · Tomi Valkeinen
Hi,
Quoted 18 lines · Mathieu Malaterre
When the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=mThe offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.
Quoted 8 lines
It should be noticed that
offb_destroyis never called which explain the need to skip error detection on the radeon side.Signed-off-by Mathieu Malaterre <[email protected]>Suggested-by Lennart Sorensen <[email protected]>---
Please always have a changelog in patch new revisions. For individual patches, you can insert the changes here.
Quoted 36 lines
drivers/video/fbdev/aty/radeon_base.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)drivers/video/fbdev/aty/radeon_base.c +18
-0@@ -2259,6 +2259,22 @@ static struct bin_attribute edid2_attr = { .read = radeon_show_edid2, }; +static int radeon_kick_out_firmware_fb (struct pci_dev *pdev) +{ +struct apertures_struct *ap; + + ap =alloc_apertures (1 ); +if (!ap) +return -ENOMEM ; + + ap->ranges[0 ].base =pci_resource_start (pdev,0 ); + ap->ranges[0 ].size =pci_resource_len (pdev,0 ); + +remove_conflicting_framebuffers (ap,KBUILD_MODNAME , false); +kfree (ap); + +return 0 ; +}static int radeonfb_pci_register (struct pci_dev *pdev,const struct pci_device_id *ent)@@ -2314,19 +2330,27 @@ static int radeonfb_pci_register(struct pci_dev *pdev, rinfo->fb_base_phys =pci_resource_start (pdev,0 ); rinfo->mmio_base_phys =pci_resource_start (pdev,2 ); + ret =radeon_kick_out_firmware_fb (pdev); +if (ret)drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2344
Quoted 10 lines
drivers/video/fbdev/aty/radeon_base.c +4
-0+return ret; +/* request the mem regions */ ret =pci_request_region (pdev,0 ,"radeonfb framebuffer" );if (ret <0 ) {printk (KERN_ERR "radeonfb (%s): cannot request region 0.\n" ,pci_name (rinfo->pdev)); +#ifndef CONFIG_PPC goto err_release_fb; +#endif If this is not a problem on PPC, the kernel shouldn't print an error either.
drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2353
Quoted 9 lines
drivers/video/fbdev/aty/radeon_base.c +2
-0} ret =pci_request_region (pdev,2 ,"radeonfb mmio" );if (ret <0 ) {printk (KERN_ERR "radeonfb (%s): cannot request region 2.\n" ,pci_name (rinfo->pdev)); +#ifndef CONFIG_PPC goto err_release_pci0; +#endif Same here.
Quoted 12 lines
drivers/video/fbdev/aty/radeon_base.c +1
-0}/* map the regions */ @@ -2511,10 +2535,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,iounmap (rinfo->mmio_base); err_release_pci2:pci_release_region (pdev,2 ); +#ifndef CONFIG_PPC err_release_pci0:pci_release_region (pdev,0 ); err_release_fb:framebuffer_release (info);
Quoted 8 lines
drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2546
Quoted 5 lines
drivers/video/fbdev/aty/radeon_base.c +1
-0+#endif err_disable: err_out:return ret;So I don't quite follow what's going on here. Why the
CONFIG_PPCconditionals? Is this problem only with OFFB and only with PPC?
I don't think so. I am no convinced the pci_request_region even serves a purpose. Certainly a number of the other drivers don't even bother doing it.
The problem is that offb does do it, and radeon_fb tries to do it, and since one is trying to take over from the other, it can't do that because the area is already reserved.
Quoted 3 lines
And I think the code itself should have comments on this rather strange
behavior: the driver fails to get HW resources, but decides to ignore the failure on PPC.
It seems the simpler answer is to just not do it at all.
Now if some architectures require you to do it (no idea), then that could be an issue.
Looking at all the other FB drivers, none of the ones that support kicking out another driver to takeover call pci_request_region. The ones that do call it all appear to be older drivers, likely not updated much lately.
Signature · 1 line
Len Sorensen
Tomi,
Quoted 106 lines · Tomi Valkeinen
Hi,
Quoted 18 lines · Mathieu Malaterre
When the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=mThe offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.
Quoted 8 lines
It should be noticed that
offb_destroyis never called which explain the need to skip error detection on the radeon side.Signed-off-by Mathieu Malaterre <[email protected]>Suggested-by Lennart Sorensen <[email protected]>---
Please always have a changelog in patch new revisions. For individual patches, you can insert the changes here.
Quoted 36 lines
drivers/video/fbdev/aty/radeon_base.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)drivers/video/fbdev/aty/radeon_base.c +18
-0@@ -2259,6 +2259,22 @@ static struct bin_attribute edid2_attr = { .read = radeon_show_edid2, }; +static int radeon_kick_out_firmware_fb (struct pci_dev *pdev) +{ +struct apertures_struct *ap; + + ap =alloc_apertures (1 ); +if (!ap) +return -ENOMEM ; + + ap->ranges[0 ].base =pci_resource_start (pdev,0 ); + ap->ranges[0 ].size =pci_resource_len (pdev,0 ); + +remove_conflicting_framebuffers (ap,KBUILD_MODNAME , false); +kfree (ap); + +return 0 ; +}static int radeonfb_pci_register (struct pci_dev *pdev,const struct pci_device_id *ent)@@ -2314,19 +2330,27 @@ static int radeonfb_pci_register(struct pci_dev *pdev, rinfo->fb_base_phys =pci_resource_start (pdev,0 ); rinfo->mmio_base_phys =pci_resource_start (pdev,2 ); + ret =radeon_kick_out_firmware_fb (pdev); +if (ret)drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2344
Quoted 10 lines
drivers/video/fbdev/aty/radeon_base.c +4
-0+return ret; +/* request the mem regions */ ret =pci_request_region (pdev,0 ,"radeonfb framebuffer" );if (ret <0 ) {printk (KERN_ERR "radeonfb (%s): cannot request region 0.\n" ,pci_name (rinfo->pdev)); +#ifndef CONFIG_PPC goto err_release_fb; +#endif If this is not a problem on PPC, the kernel shouldn't print an error either.
drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2353
Quoted 9 lines
drivers/video/fbdev/aty/radeon_base.c +2
-0} ret =pci_request_region (pdev,2 ,"radeonfb mmio" );if (ret <0 ) {printk (KERN_ERR "radeonfb (%s): cannot request region 2.\n" ,pci_name (rinfo->pdev)); +#ifndef CONFIG_PPC goto err_release_pci0; +#endif Same here.
Quoted 12 lines
drivers/video/fbdev/aty/radeon_base.c +1
-0}/* map the regions */ @@ -2511,10 +2535,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,iounmap (rinfo->mmio_base); err_release_pci2:pci_release_region (pdev,2 ); +#ifndef CONFIG_PPC err_release_pci0:pci_release_region (pdev,0 ); err_release_fb:framebuffer_release (info);
Quoted 8 lines
drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2546
Quoted 5 lines
drivers/video/fbdev/aty/radeon_base.c +1
-0+#endif err_disable: err_out:return ret;So I don't quite follow what's going on here. Why the
CONFIG_PPCconditionals? Is this problem only with OFFB and only with PPC?
The radeonfb fails to load only (conflict with offb):
- when on PPC (PMAC actually)
- when compiled as module (CONFIG_FB_RADEON=y is OK)
Quoted 3 lines
And I think the code itself should have comments on this rather strange
behavior: the driver fails to get HW resources, but decides to ignore the failure on PPC.
Actually you are right, I missed configuration such as Pegasos[0] machine (no openfirmware-framebuffer implemented in their firmware at all). So I cannot simply assume that offb already allocated stuff on all PPC out there.
Will resent a v3 with proper changelog ASAP.
PATCH v3 1/1 Fix loading of module radeonfb on PowerMac
In reply to Mathieu MalaterreWhen the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=m
The offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16
This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.
It should be noticed that offb_destroy is never called which explain the need to skip error detection on the radeon side.
---
v2: Only fails when CONFIG_PCC is not set
v3: Only fails when CONFIG_FB_OF is not set, CONFIG_PCC was too broad. Since the conflicts in region is due to OFfb explicitly refers to it.
drivers/video/fbdev/aty/radeon_base.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)
drivers/video/fbdev/aty/radeon_base.c +26 -0
@@ -2259,6 +2259,22 @@ static const struct bin_attribute edid2_attr = { .read = radeon_show_edid2, }; +static int radeon_kick_out_firmware_fb (struct pci_dev *pdev) +{ +struct apertures_struct *ap; + + ap =alloc_apertures (1 ); +if (!ap) +return -ENOMEM ; + + ap->ranges[0 ].base =pci_resource_start (pdev,0 ); + ap->ranges[0 ].size =pci_resource_len (pdev,0 ); + +remove_conflicting_framebuffers (ap,KBUILD_MODNAME , false); +kfree (ap); + +return 0 ; +}static int radeonfb_pci_register (struct pci_dev *pdev,const struct pci_device_id *ent)
@@ -2312,19 +2328,27 @@ static int radeonfb_pci_register(struct pci_dev *pdev, rinfo->fb_base_phys =pci_resource_start (pdev,0 ); rinfo->mmio_base_phys =pci_resource_start (pdev,2 ); + ret =radeon_kick_out_firmware_fb (pdev); +if (ret) +return ret; +/* request the mem regions */ ret =pci_request_region (pdev,0 ,"radeonfb framebuffer" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 0.\n" ,pci_name (rinfo->pdev)); goto err_release_fb; +#endif } ret =pci_request_region (pdev,2 ,"radeonfb mmio" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 2.\n" ,pci_name (rinfo->pdev)); goto err_release_pci0; +#endif }/* map the regions */
@@ -2509,10 +2533,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,iounmap (rinfo->mmio_base); err_release_pci2:pci_release_region (pdev,2 ); +#ifndef CONFIG_FB_OF err_release_pci0:pci_release_region (pdev,0 ); err_release_fb:framebuffer_release (info); +#endif err_disable: err_out:return ret;
Signature · 1 line
2.11.0
Quoted 15 lines · Mathieu Malaterre
When the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=mThe offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16
Quoted 5 lines
This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.
It should be noticed that
offb_destroyis never called which explain the need to skip error detection on the radeon side.
This still needs to be explained more, from my last mail:
"The last put_fb_info() on fb_info should call ->fb_destroy (offb_destroy in our case) and remove_conflicting_framebuffers() is calling put_fb_info() so there is some extra reference on fb_info somewhere preventing it from going away.
Please look into fixing this."
Quoted 7 lines
Signed-off-by Mathieu Malaterre <[email protected]>Suggested-by Lennart Sorensen <[email protected]>---
v2: Only fails whenCONFIG_PCCis not set
v3: Only fails whenCONFIG_FB_OFis not set,CONFIG_PCCwas too broad. Since the conflicts in region is due to OFfb explicitly refers to it.
It seems that there may still be configurations when this is incorrect -> when offb drives primary (non-radeon) card and radeonfb drives secondary (radeon) card..
Quoted 61 lines
drivers/video/fbdev/aty/radeon_base.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)drivers/video/fbdev/aty/radeon_base.c +24
-0@@ -2259,6 +2259,22 @@ static const struct bin_attribute edid2_attr = { .read = radeon_show_edid2, }; +static int radeon_kick_out_firmware_fb (struct pci_dev *pdev) +{ +struct apertures_struct *ap; + + ap =alloc_apertures (1 ); +if (!ap) +return -ENOMEM ; + + ap->ranges[0 ].base =pci_resource_start (pdev,0 ); + ap->ranges[0 ].size =pci_resource_len (pdev,0 ); + +remove_conflicting_framebuffers (ap,KBUILD_MODNAME , false); +kfree (ap); + +return 0 ; +}static int radeonfb_pci_register (struct pci_dev *pdev,const struct pci_device_id *ent)@@ -2312,19 +2328,27 @@ static int radeonfb_pci_register(struct pci_dev *pdev, rinfo->fb_base_phys =pci_resource_start (pdev,0 ); rinfo->mmio_base_phys =pci_resource_start (pdev,2 ); + ret =radeon_kick_out_firmware_fb (pdev); +if (ret) +return ret; +/* request the mem regions */ ret =pci_request_region (pdev,0 ,"radeonfb framebuffer" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 0.\n" ,pci_name (rinfo->pdev)); goto err_release_fb; +#endif } ret =pci_request_region (pdev,2 ,"radeonfb mmio" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 2.\n" ,pci_name (rinfo->pdev)); goto err_release_pci0; +#endif }/* map the regions */ @@ -2509,10 +2533,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,iounmap (rinfo->mmio_base); err_release_pci2:
drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2544
Quoted 10 lines
drivers/video/fbdev/aty/radeon_base.c +2
-0pci_release_region (pdev,2 ); +#ifndef CONFIG_FB_OF err_release_pci0:pci_release_region (pdev,0 ); err_release_fb:framebuffer_release (info); +#endif err_disable: err_out:return ret;
Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
Quoted 22 lines · Bartlomiej Zolnierkiewicz
Quoted 15 lines · Mathieu Malaterre
When the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=mThe offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16Quoted 5 lines
This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.
It should be noticed that
offb_destroyis never called which explain the need to skip error detection on the radeon side.
Quoted 8 lines
This still needs to be explained more, from my last mail:
"The last
put_fb_info()onfb_infoshould call ->fb_destroy (offb_destroyin our case) andremove_conflicting_framebuffers()is callingput_fb_info()so there is some extra reference onfb_infosomewhere preventing it from going away.Please look into fixing this."
My impression of that problem is that the offb driver is in use because it is running the console, and until the radeonfb driver is loaded and ready to take over, you can't stop using the offb driver, but you can't currently load the radeonfb because offb is holding resources it wants.
Maybe I have misunderstood what the code is doing, but that seems to be the problem.
On an x86 PC you could drop one fb and go to text mode then start another fb driver. PPC doesn't have that option since there is no text mode.
Signature · 1 line
Len Sorensen
Hi Bartlomiej,
Quoted 37 lines · Lennart Sorensen
Quoted 22 lines · Bartlomiej Zolnierkiewicz
Quoted 15 lines · Mathieu Malaterre
When the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=mThe offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16Quoted 5 lines
This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.
It should be noticed that
offb_destroyis never called which explain the need to skip error detection on the radeon side.Quoted 8 lines
This still needs to be explained more, from my last mail:
"The last
put_fb_info()onfb_infoshould call ->fb_destroy (offb_destroyin our case) andremove_conflicting_framebuffers()is callingput_fb_info()so there is some extra reference onfb_infosomewhere preventing it from going away.Please look into fixing this."
My impression of that problem is that the offb driver is in use because it is running the console, and until the radeonfb driver is loaded and ready to take over, you can't stop using the offb driver, but you can't currently load the radeonfb because offb is holding resources it wants.
Quoted 5 lines
Maybe I have misunderstood what the code is doing, but that seems to be the problem.
On an x86 PC you could drop one fb and go to text mode then start another fb driver. PPC doesn't have that option since there is no text mode.
For reference my patch was inspired by commit:
https://github.com/torvalds/linux/commit/a56f7428d7534f162fbb089c5c79012bf38a7c29
While doing the search, I discover my patch is incorrect, I need to integrate change from:
So I'll submit a v4 anyway.
Thanks all,
Bartlomiej,
Quoted 23 lines · Bartlomiej Zolnierkiewicz
Quoted 15 lines · Mathieu Malaterre
When the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=mThe offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16Quoted 5 lines
This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.
It should be noticed that
offb_destroyis never called which explain the need to skip error detection on the radeon side.
Quoted 8 lines
This still needs to be explained more, from my last mail:
"The last
put_fb_info()onfb_infoshould call ->fb_destroy (offb_destroyin our case) andremove_conflicting_framebuffers()is callingput_fb_info()so there is some extra reference onfb_infosomewhere preventing it from going away.Please look into fixing this."
I am not familiar with the fb stuff internals but here is what I see:
# modprobe radeonfb
leads to:
[ 52.058546] bus: 'pci': add driver radeonfb [ 52.058588] bus: 'pci': driver_probe_device: matched device 0000:00:10.0 with driver radeonfb [ 52.058595] bus: 'pci': really_probe: probing driver radeonfb with device 0000:00:10.0 [ 52.058608] devices_kset: Moving 0000:00:10.0 to end of list [ 52.058613] radeonfb_pci_register BEGIN [ 52.058634] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) <at this point radeon_kick_out_firmware_fb is called> [ 52.058666] checking generic (9c008000 96000) vs hw (98000000 8000000) [ 52.058667] fb: switching to radeonfb from OFfb ATY,RockHo [ 52.058844] Console: switching to colour dummy device 80x25 [ 52.058860] device: 'fb0': device_unregister [ 52.058956] PM: Removing info for No Bus:fb0 [ 52.059014] device: 'fb0': device_create_release <a call to do_unregister_framebuffer is done> <put_fb_info is done with a count=2 and dev=NULL> [ 52.059048] device: 'vtcon1': device_unregister [ 52.059076] PM: Removing info for No Bus:vtcon1 [ 52.059091] device: 'vtcon1': device_create_release [ 52.059107] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 52.256151] aper_base: 98000000 MC_FB_LOC to: 9bff9800, MC_AGP_LOC to: ffffa000 [ 52.256157] radeonfb (0000:00:10.0): Found 32768k of DDR 64 bits
wide videoram
I can confirm that offb_destroy is never called (not sure exactly why), but in any case the call to radeon_kick_out_firmware_fb happen much earlier, at least before the put_fb_info.
Could you describe a bit more the chain of calls you were thinking of ?
Quoted 81 lines
Quoted 7 lines
Signed-off-by Mathieu Malaterre <[email protected]>Suggested-by Lennart Sorensen <[email protected]>---
v2: Only fails whenCONFIG_PCCis not set
v3: Only fails whenCONFIG_FB_OFis not set,CONFIG_PCCwas too broad. Since the conflicts in region is due to OFfb explicitly refers to it.It seems that there may still be configurations when this is incorrect -> when offb drives primary (non-radeon) card and radeonfb drives secondary (radeon) card..
Quoted 69 lines
drivers/video/fbdev/aty/radeon_base.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)drivers/video/fbdev/aty/radeon_base.c +26
-0@@ -2259,6 +2259,22 @@ static const struct bin_attribute edid2_attr = { .read = radeon_show_edid2, }; +static int radeon_kick_out_firmware_fb (struct pci_dev *pdev) +{ +struct apertures_struct *ap; + + ap =alloc_apertures (1 ); +if (!ap) +return -ENOMEM ; + + ap->ranges[0 ].base =pci_resource_start (pdev,0 ); + ap->ranges[0 ].size =pci_resource_len (pdev,0 ); + +remove_conflicting_framebuffers (ap,KBUILD_MODNAME , false); +kfree (ap); + +return 0 ; +}static int radeonfb_pci_register (struct pci_dev *pdev,const struct pci_device_id *ent)@@ -2312,19 +2328,27 @@ static int radeonfb_pci_register(struct pci_dev *pdev, rinfo->fb_base_phys =pci_resource_start (pdev,0 ); rinfo->mmio_base_phys =pci_resource_start (pdev,2 ); + ret =radeon_kick_out_firmware_fb (pdev); +if (ret) +return ret; +/* request the mem regions */ ret =pci_request_region (pdev,0 ,"radeonfb framebuffer" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 0.\n" ,pci_name (rinfo->pdev)); goto err_release_fb; +#endif } ret =pci_request_region (pdev,2 ,"radeonfb mmio" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 2.\n" ,pci_name (rinfo->pdev)); goto err_release_pci0; +#endif }/* map the regions */ @@ -2509,10 +2533,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,iounmap (rinfo->mmio_base); err_release_pci2:pci_release_region (pdev,2 ); +#ifndef CONFIG_FB_OF err_release_pci0:pci_release_region (pdev,0 ); err_release_fb:framebuffer_release (info); +#endif err_disable:
Quoted 9 lines
drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2544
Quoted 2 lines
drivers/video/fbdev/aty/radeon_base.c +0
-0err_out:return ret;Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
Thanks,
-M
Quoted 67 lines · Mathieu Malaterre
Bartlomiej,
Quoted 23 lines · Bartlomiej Zolnierkiewicz
Quoted 15 lines · Mathieu Malaterre
When the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=mThe offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16Quoted 5 lines
This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.
It should be noticed that
offb_destroyis never called which explain the need to skip error detection on the radeon side.Quoted 8 lines
This still needs to be explained more, from my last mail:
"The last
put_fb_info()onfb_infoshould call ->fb_destroy (offb_destroyin our case) andremove_conflicting_framebuffers()is callingput_fb_info()so there is some extra reference onfb_infosomewhere preventing it from going away.Please look into fixing this."
I am not familiar with the fb stuff internals but here is what I see:
# modprobe radeonfbleads to:
[ 52.058546] bus: 'pci': add driver radeonfb [ 52.058588] bus: 'pci': driver_probe_device: matched device 0000:00:10.0 with driver radeonfb [ 52.058595] bus: 'pci': really_probe: probing driver radeonfb with device 0000:00:10.0 [ 52.058608] devices_kset: Moving 0000:00:10.0 to end of list [ 52.058613] radeonfb_pci_register BEGIN [ 52.058634] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) <at this point radeon_kick_out_firmware_fb is called> [ 52.058666] checking generic (9c008000 96000) vs hw (98000000 8000000) [ 52.058667] fb: switching to radeonfb from OFfb ATY,RockHo [ 52.058844] Console: switching to colour dummy device 80x25 [ 52.058860] device: 'fb0': device_unregister [ 52.058956] PM: Removing info for No Bus:fb0 [ 52.059014] device: 'fb0': device_create_release <a call to do_unregister_framebuffer is done> <put_fb_info is done with a count=2 and dev=NULL> [ 52.059048] device: 'vtcon1': device_unregister [ 52.059076] PM: Removing info for No Bus:vtcon1 [ 52.059091] device: 'vtcon1': device_create_release [ 52.059107] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 52.256151] aper_base: 98000000 MC_FB_LOC to: 9bff9800, MC_AGP_LOC to: ffffa000 [ 52.256157] radeonfb (0000:00:10.0): Found 32768k of DDR 64 bits
Quoted 5 lines
wide videoram
I can confirm that
offb_destroyis never called (not sure exactly why), but in any case the call toradeon_kick_out_firmware_fbhappen much earlier, at least before theput_fb_info.
It is okay, put_fb_info() is called indirectly by radeon_kick_out_firmware_fb()
radeon_kick_out_firmware_fb()
remove_conflicting_framebuffers() do_remove_conflicting_framebuffers() do_unregister_framebuffer() put_fb_info()
offb_destroy() is not called because there is an extra reference on old fb_info (->count == 2):
static void put_fb_info(struct fb_info *fb_info)
{
if (!atomic_dec_and_test(&fb_info->count))
return;
if (fb_info->fbops->fb_destroy)
fb_info->fbops->fb_destroy(fb_info);
}The question is why there is an extra reference, probably user-space is still holding the fb_info reference obtained in fb_open() call and fb_release() is never called. Besides not calling fbops->fb_destroy() this also causes missing call of fbops->fb_release() (in fb_release()) which some fb drivers are implementing (but not offb.c).
Quoted 1 line
Could you describe a bit more the chain of calls you were thinking of ?
Please add WARN_ON(1) to get_fb_info() and put_fb_info() so we can check from the stacktrace if it is actually fb_open() that holds the extra old fb_info reference.
drivers/video/fbdev/core/fbmem.c:
static struct fb_info *get_fb_info(unsigned int idx)
{
struct fb_info *fb_info;
if (idx >= FB_MAX)
return ERR_PTR(-ENODEV);
mutex_lock(®istration_lock);
fb_info = registered_fb[idx];
if (fb_info)
atomic_inc(&fb_info->count);if (fb_info)
WARN_ON(1); mutex_unlock(®istration_lock); return fb_info; }
static void put_fb_info(struct fb_info *fb_info)
{WARN_ON(1);
if (!atomic_dec_and_test(&fb_info->count)) return; if (fb_info->fbops->fb_destroy) fb_info->fbops->fb_destroy(fb_info); }
Quoted 91 lines
Quoted 81 lines
Quoted 7 lines
Signed-off-by Mathieu Malaterre <[email protected]>Suggested-by Lennart Sorensen <[email protected]>---
v2: Only fails whenCONFIG_PCCis not set
v3: Only fails whenCONFIG_FB_OFis not set,CONFIG_PCCwas too broad. Since the conflicts in region is due to OFfb explicitly refers to it.It seems that there may still be configurations when this is incorrect -> when offb drives primary (non-radeon) card and radeonfb drives secondary (radeon) card..
Quoted 69 lines
drivers/video/fbdev/aty/radeon_base.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)drivers/video/fbdev/aty/radeon_base.c +26
-0@@ -2259,6 +2259,22 @@ static const struct bin_attribute edid2_attr = { .read = radeon_show_edid2, }; +static int radeon_kick_out_firmware_fb (struct pci_dev *pdev) +{ +struct apertures_struct *ap; + + ap =alloc_apertures (1 ); +if (!ap) +return -ENOMEM ; + + ap->ranges[0 ].base =pci_resource_start (pdev,0 ); + ap->ranges[0 ].size =pci_resource_len (pdev,0 ); + +remove_conflicting_framebuffers (ap,KBUILD_MODNAME , false); +kfree (ap); + +return 0 ; +}static int radeonfb_pci_register (struct pci_dev *pdev,const struct pci_device_id *ent)@@ -2312,19 +2328,27 @@ static int radeonfb_pci_register(struct pci_dev *pdev, rinfo->fb_base_phys =pci_resource_start (pdev,0 ); rinfo->mmio_base_phys =pci_resource_start (pdev,2 ); + ret =radeon_kick_out_firmware_fb (pdev); +if (ret) +return ret; +/* request the mem regions */ ret =pci_request_region (pdev,0 ,"radeonfb framebuffer" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 0.\n" ,pci_name (rinfo->pdev)); goto err_release_fb; +#endif } ret =pci_request_region (pdev,2 ,"radeonfb mmio" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 2.\n" ,pci_name (rinfo->pdev)); goto err_release_pci0; +#endif }/* map the regions */ @@ -2509,10 +2533,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,iounmap (rinfo->mmio_base); err_release_pci2:pci_release_region (pdev,2 ); +#ifndef CONFIG_FB_OF err_release_pci0:pci_release_region (pdev,0 ); err_release_fb:framebuffer_release (info); +#endif err_disable:Quoted 9 lines
drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2544
Quoted 2 lines
drivers/video/fbdev/aty/radeon_base.c +0
-0err_out:return ret;Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
Quoted 2 lines
Thanks,
-M
Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
Bartlomiej,
Quoted 131 lines · Bartlomiej Zolnierkiewicz
Quoted 67 lines · Mathieu Malaterre
Bartlomiej,
Quoted 23 lines · Bartlomiej Zolnierkiewicz
Quoted 15 lines · Mathieu Malaterre
When the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=mThe offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16Quoted 5 lines
This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.
It should be noticed that
offb_destroyis never called which explain the need to skip error detection on the radeon side.Quoted 8 lines
This still needs to be explained more, from my last mail:
"The last
put_fb_info()onfb_infoshould call ->fb_destroy (offb_destroyin our case) andremove_conflicting_framebuffers()is callingput_fb_info()so there is some extra reference onfb_infosomewhere preventing it from going away.Please look into fixing this."
I am not familiar with the fb stuff internals but here is what I see:
# modprobe radeonfbleads to:
[ 52.058546] bus: 'pci': add driver radeonfb [ 52.058588] bus: 'pci': driver_probe_device: matched device 0000:00:10.0 with driver radeonfb [ 52.058595] bus: 'pci': really_probe: probing driver radeonfb with device 0000:00:10.0 [ 52.058608] devices_kset: Moving 0000:00:10.0 to end of list [ 52.058613] radeonfb_pci_register BEGIN [ 52.058634] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) <at this point radeon_kick_out_firmware_fb is called> [ 52.058666] checking generic (9c008000 96000) vs hw (98000000 8000000) [ 52.058667] fb: switching to radeonfb from OFfb ATY,RockHo [ 52.058844] Console: switching to colour dummy device 80x25 [ 52.058860] device: 'fb0': device_unregister [ 52.058956] PM: Removing info for No Bus:fb0 [ 52.059014] device: 'fb0': device_create_release <a call to do_unregister_framebuffer is done> <put_fb_info is done with a count=2 and dev=NULL> [ 52.059048] device: 'vtcon1': device_unregister [ 52.059076] PM: Removing info for No Bus:vtcon1 [ 52.059091] device: 'vtcon1': device_create_release [ 52.059107] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 52.256151] aper_base: 98000000 MC_FB_LOC to: 9bff9800, MC_AGP_LOC to: ffffa000 [ 52.256157] radeonfb (0000:00:10.0): Found 32768k of DDR 64 bitsQuoted 5 lines
wide videoram
I can confirm that
offb_destroyis never called (not sure exactly why), but in any case the call toradeon_kick_out_firmware_fbhappen much earlier, at least before theput_fb_info.It is okay,
put_fb_info()is called indirectly byradeon_kick_out_firmware_fb()
radeon_kick_out_firmware_fb()remove_conflicting_framebuffers() do_remove_conflicting_framebuffers() do_unregister_framebuffer() put_fb_info()
offb_destroy()is not called because there is an extra reference on oldfb_info(->count == 2):static void
put_fb_info(struct fb_info *fb_info){ if (!atomic_dec_and_test(&fb_info->count)) return; if (fb_info->fbops->fb_destroy) fb_info->fbops->fb_destroy(fb_info); }The question is why there is an extra reference, probably user-space is still holding the
fb_inforeference obtained infb_open()call andfb_release()is never called. Besides not callingfbops->fb_destroy()this also causes missing call offbops->fb_release()(infb_release()) which some fb drivers are implementing (but notoffb.c).Quoted 1 line
Could you describe a bit more the chain of calls you were thinking of ?
Please add
WARN_ON(1)toget_fb_info()andput_fb_info()so we can check from the stacktrace if it is actuallyfb_open()that holds the extra oldfb_inforeference.
drivers/video/fbdev/core/fbmem.c:static struct
fb_info*get_fb_info(unsigned int idx){ struct fb_info *fb_info; if (idx >= FB_MAX) return ERR_PTR(-ENODEV); mutex_lock(®istration_lock); fb_info = registered_fb[idx]; if (fb_info) atomic_inc(&fb_info->count);if (
fb_info)WARN_ON(1); mutex_unlock(®istration_lock); return fb_info; }static void
put_fb_info(struct fb_info *fb_info)
{WARN_ON(1);
Quoted 5 lines
if (!atomic_dec_and_test(&fb_info->count))
return;
if (fb_info->fbops->fb_destroy)
fb_info->fbops->fb_destroy(fb_info);
}Alright, here is what I see:
[ 18.961639] PM: Adding info for No Bus:vcs7 [ 18.966448] device: 'vcsa7': device_add [ 18.966496] PM: Adding info for No Bus:vcsa7 [ 19.001701] WARNING: CPU: 0 PID: 405 at drivers/video/fbdev/core/fbmem.c:68 get_fb_info.part.3+0x58/0x7c [ 19.001715] Modules linked in: uinput snd_aoa_codec_toonie
snd_aoa_fabric_layout snd_aoa snd_aoa_i2sbus snd_aoa_soundbus snd_pcm snd_timer snd soundcore rack_meter evdev i2c_dev sg usb_storage ip_tables x_tables autofs4 ext4 crc16 mbcache jbd2 fscrypto hid_generic usbhid hid ohci_pci ehci_pci ohci_hcd ehci_hcd sungem firewire_ohci sungem_phy sr_mod firewire_core crc_itu_t cdrom sd_mod usbcore
[ 19.001773] CPU: 0 PID: 405 Comm: Xorg Not tainted 4.15.0+ #321
[ 19.001778] NIP: c039ef20 LR: c039eefc CTR: c039ef44
[ 19.001781] REGS: decc7c80 TRAP: 0700 Not tainted (4.15.0+)
[ 19.001784] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 28222828 XER: 00000000
[ 19.001795]
GPR00: c039eefc decc7d30 c147ab00 00000000 dc3ed8c0
df568a6c 00000001 c147ab00
GPR08: df568a6c 00000002 00000000 dc280c50 28222822
006f9ff4 006fff50 80000000
GPR16: 88000228 00000008 bfcb5b08 00000002 decc7e60
80000000 ffffffea 00000041
GPR24: 00000000 00000006 df568a6c dc3ed8c0 df5ef1e8
df568a40 c08f7c18 dc198800
[ 19.001835] NIP [c039ef20] get_fb_info.part.3+0x58/0x7c
[ 19.001840] LR [c039eefc] get_fb_info.part.3+0x34/0x7c
[ 19.001842] Call Trace:
[ 19.001848] [decc7d30] [c039eefc] get_fb_info.part.3+0x34/0x7c (unreliable)
[ 19.001854] [decc7d40] [c039efa0] fb_open+0x5c/0x18c
[ 19.001866] [decc7d60] [c01e0e90] chrdev_open+0xb8/0x19c
[ 19.001872] [decc7d90] [c01d7994] do_dentry_open+0x24c/0x398
[ 19.001881] [decc7dc0] [c01ec378] path_openat+0x4c4/0x11b8
[ 19.001888] [decc7e50] [c01ee0d8] do_filp_open+0xbc/0x10c
[ 19.001893] [decc7f00] [c01d93b0] do_sys_open+0x158/0x228
[ 19.001901] [decc7f40] [c00181cc] ret_from_syscall+0x0/0x40
[ 19.001908] --- interrupt: c01 at 0xb751b940
LR = 0xb751b8dc
[ 19.001912] Instruction dump:
[ 19.001917] 7fc3f378 57ff103a 482cc171 3d20c093 39291a84 7fe9f82e
2f9f0000 419e0018
[ 19.001927] 7d20f828 31290001 7d20f92d 40a2fff4 <0fe00000> 7fc3f378
482cca69 7fe3fb78
[ 19.001938] ---[ end trace e0bf4192eb1c4f60 ]---
[ 19.001985] WARNING: CPU: 0 PID: 405 at
drivers/video/fbdev/core/fbmem.c:77 put_fb_info+0x18/0x68
[ 19.001988] Modules linked in: uinput snd_aoa_codec_tooniesnd_aoa_fabric_layout snd_aoa snd_aoa_i2sbus snd_aoa_soundbus snd_pcm snd_timer snd soundcore rack_meter evdev i2c_dev sg usb_storage ip_tables x_tables autofs4 ext4 crc16 mbcache jbd2 fscrypto hid_generic usbhid hid ohci_pci ehci_pci ohci_hcd ehci_hcd sungem firewire_ohci sungem_phy sr_mod firewire_core crc_itu_t cdrom sd_mod usbcore
[ 19.002028] CPU: 0 PID: 405 Comm: Xorg Tainted: G W
4.15.0+ #321
[ 19.002031] NIP: c039e6ec LR: c039eeb0 CTR: c039ee48
[ 19.002035] REGS: decc7e10 TRAP: 0700 Tainted: G W (4.15.0+)
[ 19.002037] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 28000222 XER: 20000000
[ 19.002047]
GPR00: c039eeb0 decc7ec0 c147ab00 dc198800 dc3ed8c0
dc3ed8c8 00000001 c147ab00
GPR08: 00000000 c08fa6f8 00000000 dc280c50 28000228
006f9ff4 006fff50 00000000
GPR16: 007001a8 00000008 bfcb5b08 007001a4 00000000
0070d0c4 00000002 00000000
GPR24: b6ad8b1c dc3ed8c8 df5ef1e8 df3e4ee0 dc280c50
df5ef1e8 dc19880c dc198800
[ 19.002086] NIP [c039e6ec] put_fb_info+0x18/0x68
[ 19.002091] LR [c039eeb0] fb_release+0x68/0x80
[ 19.002093] Call Trace:
[ 19.002096] [decc7ec0] [df5ef1e8] 0xdf5ef1e8 (unreliable)
[ 19.002102] [decc7ed0] [c039eeb0] fb_release+0x68/0x80
[ 19.002108] [decc7ee0] [c01dd2e8] __fput+0xb4/0x260
[ 19.002118] [decc7f10] [c006e088] task_work_run+0xc0/0xe8
[ 19.002129] [decc7f30] [c000aa90] do_notify_resume+0xb4/0xb8
[ 19.002135] [decc7f40] [c0018b4c] do_user_signal+0x7c/0xcc
[ 19.002140] --- interrupt: c00 at 0xb751a7d8
LR = 0xb751a7ac
[ 19.002144] Instruction dump:
[ 19.002147] 80010014 38210010 7c0803a6 4e800020 38600000 4e800020
7c0802a6 90010004
[ 19.002157] 60000000 9421fff0 7c0802a6 90010014 <0fe00000> 7d401828
314affff 7d40192d
[ 19.002168] ---[ end trace e0bf4192eb1c4f61 ]---
[ 19.002595] WARNING: CPU: 0 PID: 405 at
drivers/video/fbdev/core/fbmem.c:68 get_fb_info.part.3+0x58/0x7c
[ 19.002601] Modules linked in: uinput snd_aoa_codec_tooniesnd_aoa_fabric_layout snd_aoa snd_aoa_i2sbus snd_aoa_soundbus snd_pcm snd_timer snd soundcore rack_meter evdev i2c_dev sg usb_storage ip_tables x_tables autofs4 ext4 crc16 mbcache jbd2 fscrypto hid_generic usbhid hid ohci_pci ehci_pci ohci_hcd ehci_hcd sungem firewire_ohci sungem_phy sr_mod firewire_core crc_itu_t cdrom sd_mod usbcore
[ 19.002645] CPU: 0 PID: 405 Comm: Xorg Tainted: G W
4.15.0+ #321
[ 19.002649] NIP: c039ef20 LR: c039eefc CTR: c039ef44
[ 19.002652] REGS: decc7c80 TRAP: 0700 Tainted: G W (4.15.0+)
[ 19.002655] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 28222248 XER: 00000000
[ 19.002664]
GPR00: c039eefc decc7d30 c147ab00 00000000 deca0340
deca0348 00000001 00000000
GPR08: 00000000 00000002 00000000 dc280c50 28222842
006f9ff4 006fff50 80000000
GPR16: 88000448 00000001 00000000 00000002 decc7e60
80000000 ffffffea 00000041
GPR24: 00000000 00000006 c01e0dd8 deca0340 df5ef1e8
df568a40 c08f7c18 dc198800
[ 19.002704] NIP [c039ef20] get_fb_info.part.3+0x58/0x7c
[ 19.002708] LR [c039eefc] get_fb_info.part.3+0x34/0x7c
[ 19.002711] Call Trace:
[ 19.002716] [decc7d30] [c039eefc] get_fb_info.part.3+0x34/0x7c (unreliable)
[ 19.002722] [decc7d40] [c039efa0] fb_open+0x5c/0x18c
[ 19.002730] [decc7d60] [c01e0e90] chrdev_open+0xb8/0x19c
[ 19.002735] [decc7d90] [c01d7994] do_dentry_open+0x24c/0x398
[ 19.002743] [decc7dc0] [c01ec378] path_openat+0x4c4/0x11b8
[ 19.002748] [decc7e50] [c01ee0d8] do_filp_open+0xbc/0x10c
[ 19.002754] [decc7f00] [c01d93b0] do_sys_open+0x158/0x228
[ 19.002760] [decc7f40] [c00181cc] ret_from_syscall+0x0/0x40
[ 19.002766] --- interrupt: c01 at 0xb751b940
LR = 0xb751b8dc
[ 19.002770] Instruction dump:
[ 19.002774] 7fc3f378 57ff103a 482cc171 3d20c093 39291a84 7fe9f82e
2f9f0000 419e0018
[ 19.002784] 7d20f828 31290001 7d20f92d 40a2fff4 <0fe00000> 7fc3f378
482cca69 7fe3fb78
[ 19.002795] ---[ end trace e0bf4192eb1c4f62 ]---
[ 19.011629] gem 0002:20:0f.0 eth0: Link is up at 100 Mbps, full-duplex
[ 19.011746] gem 0002:20:0f.0 eth0: Pause is disabled
[ 19.011846] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 19.018954] device: 'input3': device_add
[ 19.019031] PM: Adding info for No Bus:input3Then later on (after modprobe radeonfb):
[ 657.135105] PM: Removing info for No Bus:fb0 [ 657.135164] device: 'fb0': device_create_release [ 657.135279] WARNING: CPU: 0 PID: 475 at drivers/video/fbdev/core/fbmem.c:77 put_fb_info+0x18/0x68 [ 657.135284] Modules linked in: radeonfb(+) uinput
snd_aoa_codec_toonie snd_aoa_fabric_layout snd_aoa snd_aoa_i2sbus snd_aoa_soundbus snd_pcm snd_timer snd soundcore rack_meter evdev i2c_dev sg usb_storage ip_tables x_tables autofs4 ext4 crc16 mbcache jbd2 fscrypto hid_generic usbhid hid ohci_pci ehci_pci ohci_hcd ehci_hcd sungem firewire_ohci sungem_phy sr_mod firewire_core crc_itu_t cdrom sd_mod usbcore
[ 657.135344] CPU: 0 PID: 475 Comm: modprobe Tainted: G W
4.15.0+ #321
[ 657.135348] NIP: c039e6ec LR: c039e834 CTR: 00000000
[ 657.135352] REGS: dec93af0 TRAP: 0700 Tainted: G W (4.15.0+)
[ 657.135355] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 24228822 XER: 20000000
[ 657.135365]
GPR00: c039e834 dec93ba0 dc28eaa0 dc198800 00000000
000005c0 00000002 00000000
GPR08: 00001032 c08c2c2c 00000000 c08c1ab0 28228424
0049ce6c e2287b5c 00000000
GPR16: c06974dc 00000007 e2284384 00000001 dec9852c
e2282610 00000000 000a0000
GPR24: c07c9d60 c07c9d2c dc19880c 00000000 dec93bb8
00000000 c0931a84 dc198800
[ 657.135405] NIP [c039e6ec] put_fb_info+0x18/0x68
[ 657.135411] LR [c039e834] do_unregister_framebuffer+0xf8/0x148
[ 657.135413] Call Trace:
[ 657.135419] [dec93bb0] [c039e834] do_unregister_framebuffer+0xf8/0x148
[ 657.135425] [dec93be0] [c039ea1c]
do_remove_conflicting_framebuffers+0x198/0x1b8
[ 657.135431] [dec93c30] [c039ea84] remove_conflicting_framebuffers+0x48/0x6c
[ 657.135474] [dec93c50] [e2274d6c]
radeonfb_pci_register+0x184/0x1838 [radeonfb]
[ 657.135481] [dec93cb0] [c037e9fc] pci_device_probe+0x110/0x180
[ 657.135492] [dec93ce0] [c045be70] driver_probe_device+0x378/0x4a0
[ 657.135497] [dec93d10] [c045c0ac] __driver_attach+0x114/0x118
[ 657.135503] [dec93d30] [c04593dc] bus_for_each_dev+0x74/0xc0
[ 657.135508] [dec93d60] [c045acd4] bus_add_driver+0x18c/0x2a0
[ 657.135515] [dec93d80] [c045ce3c] driver_register+0x94/0x13c
[ 657.135524] [dec93d90] [c0004af4] do_one_initcall+0x4c/0x178
[ 657.135536] [dec93df0] [c00ced18] do_init_module+0x70/0x1ec
[ 657.135542] [dec93e10] [c00cdcb0] load_module+0x20d8/0x26b8
[ 657.135548] [dec93ec0] [c00ce500] SyS_finit_module+0xc4/0x120
[ 657.135555] [dec93f40] [c00181cc] ret_from_syscall+0x0/0x40
[ 657.135562] --- interrupt: c01 at 0x34d450
LR = 0x476108
[ 657.135566] Instruction dump:
[ 657.135572] 80010014 38210010 7c0803a6 4e800020 38600000 4e800020
7c0802a6 90010004
[ 657.135582] 60000000 9421fff0 7c0802a6 90010014 <0fe00000> 7d401828
314affff 7d40192d
[ 657.135593] ---[ end trace e0bf4192eb1c4f63 ]---
[ 657.135613] device: 'vtcon1': device_unregister
[ 657.135644] PM: Removing info for No Bus:vtcon1Full dmesg:
https://people.debian.org/~malat/dmesg_radeonfb.txt
Does that help at all? the call stack does not make much sense to me. I am accessing the Mac Mini over ssh.
For reference, the patch I used is:
https://github.com/malaterre/linux/commit/89fd7d4438c5200a1a4fcba1d60dd701fda4f40e.patch
Quoted 91 lines
Quoted 91 lines
Quoted 90 lines
Quoted 7 lines
Signed-off-by Mathieu Malaterre <[email protected]>Suggested-by Lennart Sorensen <[email protected]>---
v2: Only fails whenCONFIG_PCCis not set
v3: Only fails whenCONFIG_FB_OFis not set,CONFIG_PCCwas too broad. Since the conflicts in region is due to OFfb explicitly refers to it.It seems that there may still be configurations when this is incorrect -> when offb drives primary (non-radeon) card and radeonfb drives secondary (radeon) card..
Quoted 61 lines
drivers/video/fbdev/aty/radeon_base.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)drivers/video/fbdev/aty/radeon_base.c +24
-0@@ -2259,6 +2259,22 @@ static const struct bin_attribute edid2_attr = { .read = radeon_show_edid2, }; +static int radeon_kick_out_firmware_fb (struct pci_dev *pdev) +{ +struct apertures_struct *ap; + + ap =alloc_apertures (1 ); +if (!ap) +return -ENOMEM ; + + ap->ranges[0 ].base =pci_resource_start (pdev,0 ); + ap->ranges[0 ].size =pci_resource_len (pdev,0 ); + +remove_conflicting_framebuffers (ap,KBUILD_MODNAME , false); +kfree (ap); + +return 0 ; +}static int radeonfb_pci_register (struct pci_dev *pdev,const struct pci_device_id *ent)@@ -2312,19 +2328,27 @@ static int radeonfb_pci_register(struct pci_dev *pdev, rinfo->fb_base_phys =pci_resource_start (pdev,0 ); rinfo->mmio_base_phys =pci_resource_start (pdev,2 ); + ret =radeon_kick_out_firmware_fb (pdev); +if (ret) +return ret; +/* request the mem regions */ ret =pci_request_region (pdev,0 ,"radeonfb framebuffer" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 0.\n" ,pci_name (rinfo->pdev)); goto err_release_fb; +#endif } ret =pci_request_region (pdev,2 ,"radeonfb mmio" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 2.\n" ,pci_name (rinfo->pdev)); goto err_release_pci0; +#endif }/* map the regions */ @@ -2509,10 +2533,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,iounmap (rinfo->mmio_base); err_release_pci2:drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2544
Quoted 10 lines
drivers/video/fbdev/aty/radeon_base.c +2
-0pci_release_region (pdev,2 ); +#ifndef CONFIG_FB_OF err_release_pci0:pci_release_region (pdev,0 ); err_release_fb:framebuffer_release (info); +#endif err_disable: err_out:return ret;Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
Quoted 8 lines
Quoted 2 lines
Thanks,
-MBest regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
Thanks much !
Quoted 336 lines · Mathieu Malaterre
Bartlomiej,
Quoted 131 lines · Bartlomiej Zolnierkiewicz
Quoted 67 lines · Mathieu Malaterre
Bartlomiej,
Quoted 23 lines · Bartlomiej Zolnierkiewicz
Quoted 15 lines · Mathieu Malaterre
When the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=mThe offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16Quoted 5 lines
This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.
It should be noticed that
offb_destroyis never called which explain the need to skip error detection on the radeon side.Quoted 8 lines
This still needs to be explained more, from my last mail:
"The last
put_fb_info()onfb_infoshould call ->fb_destroy (offb_destroyin our case) andremove_conflicting_framebuffers()is callingput_fb_info()so there is some extra reference onfb_infosomewhere preventing it from going away.Please look into fixing this."
I am not familiar with the fb stuff internals but here is what I see:
# modprobe radeonfbleads to:
[ 52.058546] bus: 'pci': add driver radeonfb [ 52.058588] bus: 'pci': driver_probe_device: matched device 0000:00:10.0 with driver radeonfb [ 52.058595] bus: 'pci': really_probe: probing driver radeonfb with device 0000:00:10.0 [ 52.058608] devices_kset: Moving 0000:00:10.0 to end of list [ 52.058613] radeonfb_pci_register BEGIN [ 52.058634] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) <at this point radeon_kick_out_firmware_fb is called> [ 52.058666] checking generic (9c008000 96000) vs hw (98000000 8000000) [ 52.058667] fb: switching to radeonfb from OFfb ATY,RockHo [ 52.058844] Console: switching to colour dummy device 80x25 [ 52.058860] device: 'fb0': device_unregister [ 52.058956] PM: Removing info for No Bus:fb0 [ 52.059014] device: 'fb0': device_create_release <a call to do_unregister_framebuffer is done> <put_fb_info is done with a count=2 and dev=NULL> [ 52.059048] device: 'vtcon1': device_unregister [ 52.059076] PM: Removing info for No Bus:vtcon1 [ 52.059091] device: 'vtcon1': device_create_release [ 52.059107] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 52.256151] aper_base: 98000000 MC_FB_LOC to: 9bff9800, MC_AGP_LOC to: ffffa000 [ 52.256157] radeonfb (0000:00:10.0): Found 32768k of DDR 64 bitsQuoted 5 lines
wide videoram
I can confirm that
offb_destroyis never called (not sure exactly why), but in any case the call toradeon_kick_out_firmware_fbhappen much earlier, at least before theput_fb_info.It is okay,
put_fb_info()is called indirectly byradeon_kick_out_firmware_fb()
radeon_kick_out_firmware_fb()remove_conflicting_framebuffers() do_remove_conflicting_framebuffers() do_unregister_framebuffer() put_fb_info()
offb_destroy()is not called because there is an extra reference on oldfb_info(->count = 2):static void
put_fb_info(struct fb_info *fb_info){ if (!atomic_dec_and_test(&fb_info->count)) return; if (fb_info->fbops->fb_destroy) fb_info->fbops->fb_destroy(fb_info); }The question is why there is an extra reference, probably user-space is still holding the
fb_inforeference obtained infb_open()call andfb_release()is never called. Besides not callingfbops->fb_destroy()this also causes missing call offbops->fb_release()(infb_release()) which some fb drivers are implementing (but notoffb.c).Quoted 1 line
Could you describe a bit more the chain of calls you were thinking of ?
Please add
WARN_ON(1)toget_fb_info()andput_fb_info()so we can check from the stacktrace if it is actuallyfb_open()that holds the extra oldfb_inforeference.
drivers/video/fbdev/core/fbmem.c:static struct
fb_info*get_fb_info(unsigned int idx){ struct fb_info *fb_info; if (idx >= FB_MAX) return ERR_PTR(-ENODEV); mutex_lock(®istration_lock); fb_info = registered_fb[idx]; if (fb_info) atomic_inc(&fb_info->count);if (
fb_info)WARN_ON(1); mutex_unlock(®istration_lock); return fb_info; }static void
put_fb_info(struct fb_info *fb_info)
{WARN_ON(1);Quoted 5 lines
if (!atomic_dec_and_test(&fb_info->count)) return; if (fb_info->fbops->fb_destroy) fb_info->fbops->fb_destroy(fb_info); }Alright, here is what I see:
[ 18.961639] PM: Adding info for No Bus:vcs7 [ 18.966448] device: 'vcsa7': device_add [ 18.966496] PM: Adding info for No Bus:vcsa7 [ 19.001701] WARNING: CPU: 0 PID: 405 at drivers/video/fbdev/core/fbmem.c:68 get_fb_info.part.3+0x58/0x7c [ 19.001715] Modules linked in: uinput snd_aoa_codec_toonie
snd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 19.001773] CPU: 0 PID: 405 Comm: Xorg Not tainted 4.15.0+ #321 [ 19.001778] NIP: c039ef20 LR: c039eefc CTR: c039ef44 [ 19.001781] REGS: decc7c80 TRAP: 0700 Not tainted (4.15.0+) [ 19.001784] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 28222828 XER: 00000000 [ 19.001795] GPR00: c039eefc decc7d30 c147ab00 00000000 dc3ed8c0 df568a6c 00000001 c147ab00 GPR08: df568a6c 00000002 00000000 dc280c50 28222822 006f9ff4 006fff50 80000000 GPR16: 88000228 00000008 bfcb5b08 00000002 decc7e60 80000000 ffffffea 00000041 GPR24: 00000000 00000006 df568a6c dc3ed8c0 df5ef1e8 df568a40 c08f7c18 dc198800 [ 19.001835] NIP [c039ef20] get_fb_info.part.3+0x58/0x7c [ 19.001840] LR [c039eefc] get_fb_info.part.3+0x34/0x7c [ 19.001842] Call Trace: [ 19.001848] [decc7d30] [c039eefc] get_fb_info.part.3+0x34/0x7c (unreliable) [ 19.001854] [decc7d40] [c039efa0] fb_open+0x5c/0x18c [ 19.001866] [decc7d60] [c01e0e90] chrdev_open+0xb8/0x19c [ 19.001872] [decc7d90] [c01d7994] do_dentry_open+0x24c/0x398 [ 19.001881] [decc7dc0] [c01ec378] path_openat+0x4c4/0x11b8 [ 19.001888] [decc7e50] [c01ee0d8] do_filp_open+0xbc/0x10c [ 19.001893] [decc7f00] [c01d93b0] do_sys_open+0x158/0x228 [ 19.001901] [decc7f40] [c00181cc] ret_from_syscall+0x0/0x40 [ 19.001908] --- interrupt: c01 at 0xb751b940 LR = 0xb751b8dc [ 19.001912] Instruction dump: [ 19.001917] 7fc3f378 57ff103a 482cc171 3d20c093 39291a84 7fe9f82e 2f9f0000 419e0018 [ 19.001927] 7d20f828 31290001 7d20f92d 40a2fff4 <0fe00000> 7fc3f378 482cca69 7fe3fb78 [ 19.001938] ---[ end trace e0bf4192eb1c4f60 ]--- [ 19.001985] WARNING: CPU: 0 PID: 405 at drivers/video/fbdev/core/fbmem.c:77 put_fb_info+0x18/0x68 [ 19.001988] Modules linked in: uinput snd_aoa_codec_toonie
snd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 19.002028] CPU: 0 PID: 405 Comm: Xorg Tainted: G W 4.15.0+ #321 [ 19.002031] NIP: c039e6ec LR: c039eeb0 CTR: c039ee48 [ 19.002035] REGS: decc7e10 TRAP: 0700 Tainted: G W (4.15.0+) [ 19.002037] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 28000222 XER: 20000000 [ 19.002047] GPR00: c039eeb0 decc7ec0 c147ab00 dc198800 dc3ed8c0 dc3ed8c8 00000001 c147ab00 GPR08: 00000000 c08fa6f8 00000000 dc280c50 28000228 006f9ff4 006fff50 00000000 GPR16: 007001a8 00000008 bfcb5b08 007001a4 00000000 0070d0c4 00000002 00000000 GPR24: b6ad8b1c dc3ed8c8 df5ef1e8 df3e4ee0 dc280c50 df5ef1e8 dc19880c dc198800 [ 19.002086] NIP [c039e6ec] put_fb_info+0x18/0x68 [ 19.002091] LR [c039eeb0] fb_release+0x68/0x80 [ 19.002093] Call Trace: [ 19.002096] [decc7ec0] [df5ef1e8] 0xdf5ef1e8 (unreliable) [ 19.002102] [decc7ed0] [c039eeb0] fb_release+0x68/0x80 [ 19.002108] [decc7ee0] [c01dd2e8] __fput+0xb4/0x260 [ 19.002118] [decc7f10] [c006e088] task_work_run+0xc0/0xe8 [ 19.002129] [decc7f30] [c000aa90] do_notify_resume+0xb4/0xb8 [ 19.002135] [decc7f40] [c0018b4c] do_user_signal+0x7c/0xcc [ 19.002140] --- interrupt: c00 at 0xb751a7d8 LR = 0xb751a7ac [ 19.002144] Instruction dump: [ 19.002147] 80010014 38210010 7c0803a6 4e800020 38600000 4e800020 7c0802a6 90010004 [ 19.002157] 60000000 9421fff0 7c0802a6 90010014 <0fe00000> 7d401828 314affff 7d40192d [ 19.002168] ---[ end trace e0bf4192eb1c4f61 ]--- [ 19.002595] WARNING: CPU: 0 PID: 405 at drivers/video/fbdev/core/fbmem.c:68 get_fb_info.part.3+0x58/0x7c [ 19.002601] Modules linked in: uinput snd_aoa_codec_toonie
snd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 19.002645] CPU: 0 PID: 405 Comm: Xorg Tainted: G W 4.15.0+ #321 [ 19.002649] NIP: c039ef20 LR: c039eefc CTR: c039ef44 [ 19.002652] REGS: decc7c80 TRAP: 0700 Tainted: G W (4.15.0+) [ 19.002655] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 28222248 XER: 00000000 [ 19.002664] GPR00: c039eefc decc7d30 c147ab00 00000000 deca0340 deca0348 00000001 00000000 GPR08: 00000000 00000002 00000000 dc280c50 28222842 006f9ff4 006fff50 80000000 GPR16: 88000448 00000001 00000000 00000002 decc7e60 80000000 ffffffea 00000041 GPR24: 00000000 00000006 c01e0dd8 deca0340 df5ef1e8 df568a40 c08f7c18 dc198800 [ 19.002704] NIP [c039ef20] get_fb_info.part.3+0x58/0x7c [ 19.002708] LR [c039eefc] get_fb_info.part.3+0x34/0x7c [ 19.002711] Call Trace: [ 19.002716] [decc7d30] [c039eefc] get_fb_info.part.3+0x34/0x7c (unreliable) [ 19.002722] [decc7d40] [c039efa0] fb_open+0x5c/0x18c [ 19.002730] [decc7d60] [c01e0e90] chrdev_open+0xb8/0x19c [ 19.002735] [decc7d90] [c01d7994] do_dentry_open+0x24c/0x398 [ 19.002743] [decc7dc0] [c01ec378] path_openat+0x4c4/0x11b8 [ 19.002748] [decc7e50] [c01ee0d8] do_filp_open+0xbc/0x10c [ 19.002754] [decc7f00] [c01d93b0] do_sys_open+0x158/0x228 [ 19.002760] [decc7f40] [c00181cc] ret_from_syscall+0x0/0x40 [ 19.002766] --- interrupt: c01 at 0xb751b940 LR = 0xb751b8dc [ 19.002770] Instruction dump: [ 19.002774] 7fc3f378 57ff103a 482cc171 3d20c093 39291a84 7fe9f82e 2f9f0000 419e0018 [ 19.002784] 7d20f828 31290001 7d20f92d 40a2fff4 <0fe00000> 7fc3f378 482cca69 7fe3fb78 [ 19.002795] ---[ end trace e0bf4192eb1c4f62 ]--- [ 19.011629] gem 0002:20:0f.0 eth0: Link is up at 100 Mbps, full-duplex [ 19.011746] gem 0002:20:0f.0 eth0: Pause is disabled [ 19.011846] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 19.018954] device: 'input3': device_add [ 19.019031] PM: Adding info for No Bus:input3Then later on (after modprobe radeonfb):
[ 657.135105] PM: Removing info for No Bus:fb0 [ 657.135164] device: 'fb0': device_create_release [ 657.135279] WARNING: CPU: 0 PID: 475 at drivers/video/fbdev/core/fbmem.c:77 put_fb_info+0x18/0x68 [ 657.135284] Modules linked in: radeonfb(+) uinput
snd_aoa_codec_tooniesnd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 657.135344] CPU: 0 PID: 475 Comm: modprobe Tainted: G W 4.15.0+ #321 [ 657.135348] NIP: c039e6ec LR: c039e834 CTR: 00000000 [ 657.135352] REGS: dec93af0 TRAP: 0700 Tainted: G W (4.15.0+) [ 657.135355] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 24228822 XER: 20000000 [ 657.135365] GPR00: c039e834 dec93ba0 dc28eaa0 dc198800 00000000 000005c0 00000002 00000000 GPR08: 00001032 c08c2c2c 00000000 c08c1ab0 28228424 0049ce6c e2287b5c 00000000 GPR16: c06974dc 00000007 e2284384 00000001 dec9852c e2282610 00000000 000a0000 GPR24: c07c9d60 c07c9d2c dc19880c 00000000 dec93bb8 00000000 c0931a84 dc198800 [ 657.135405] NIP [c039e6ec] put_fb_info+0x18/0x68 [ 657.135411] LR [c039e834] do_unregister_framebuffer+0xf8/0x148 [ 657.135413] Call Trace: [ 657.135419] [dec93bb0] [c039e834] do_unregister_framebuffer+0xf8/0x148 [ 657.135425] [dec93be0] [c039ea1c] do_remove_conflicting_framebuffers+0x198/0x1b8 [ 657.135431] [dec93c30] [c039ea84] remove_conflicting_framebuffers+0x48/0x6c [ 657.135474] [dec93c50] [e2274d6c] radeonfb_pci_register+0x184/0x1838 [radeonfb] [ 657.135481] [dec93cb0] [c037e9fc] pci_device_probe+0x110/0x180 [ 657.135492] [dec93ce0] [c045be70] driver_probe_device+0x378/0x4a0 [ 657.135497] [dec93d10] [c045c0ac] __driver_attach+0x114/0x118 [ 657.135503] [dec93d30] [c04593dc] bus_for_each_dev+0x74/0xc0 [ 657.135508] [dec93d60] [c045acd4] bus_add_driver+0x18c/0x2a0 [ 657.135515] [dec93d80] [c045ce3c] driver_register+0x94/0x13c [ 657.135524] [dec93d90] [c0004af4] do_one_initcall+0x4c/0x178 [ 657.135536] [dec93df0] [c00ced18] do_init_module+0x70/0x1ec [ 657.135542] [dec93e10] [c00cdcb0] load_module+0x20d8/0x26b8 [ 657.135548] [dec93ec0] [c00ce500] SyS_finit_module+0xc4/0x120 [ 657.135555] [dec93f40] [c00181cc] ret_from_syscall+0x0/0x40 [ 657.135562] --- interrupt: c01 at 0x34d450 LR = 0x476108 [ 657.135566] Instruction dump: [ 657.135572] 80010014 38210010 7c0803a6 4e800020 38600000 4e800020 7c0802a6 90010004 [ 657.135582] 60000000 9421fff0 7c0802a6 90010014 <0fe00000> 7d401828 314affff 7d40192d [ 657.135593] ---[ end trace e0bf4192eb1c4f63 ]--- [ 657.135613] device: 'vtcon1': device_unregister [ 657.135644] PM: Removing info for No Bus:vtcon1
Quoted 5 lines
Full dmesg:
https://people.debian.org/~malat/dmesg_radeonfb.txtDoes that help at all? the call stack does not make much sense to me. I am accessing the Mac Mini over ssh.
Thank you, it helps.
User-space is holding reference on the /dev/fb0 and old fb_info (from offb) while offb is being replaced by radeonfb (this is why ->fb_destroy is never called). You may try checking with lsof command to see what is holding /dev/fb0 open..
Quoted 88 lines
For reference, the patch I used is:
https://github.com/malaterre/linux/commit/89fd7d4438c5200a1a4fcba1d60dd701fda4f40e.patchQuoted 84 lines
Quoted 84 lines
Quoted 84 lines
Quoted 7 lines
Signed-off-by Mathieu Malaterre <[email protected]>Suggested-by Lennart Sorensen <[email protected]>---
v2: Only fails whenCONFIG_PCCis not set
v3: Only fails whenCONFIG_FB_OFis not set,CONFIG_PCCwas too broad. Since the conflicts in region is due to OFfb explicitly refers to it.It seems that there may still be configurations when this is incorrect -> when offb drives primary (non-radeon) card and radeonfb drives secondary (radeon) card..
Quoted 71 lines
drivers/video/fbdev/aty/radeon_base.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)drivers/video/fbdev/aty/radeon_base.c +26
-0@@ -2259,6 +2259,22 @@ static const struct bin_attribute edid2_attr = { .read = radeon_show_edid2, }; +static int radeon_kick_out_firmware_fb (struct pci_dev *pdev) +{ +struct apertures_struct *ap; + + ap =alloc_apertures (1 ); +if (!ap) +return -ENOMEM ; + + ap->ranges[0 ].base =pci_resource_start (pdev,0 ); + ap->ranges[0 ].size =pci_resource_len (pdev,0 ); + +remove_conflicting_framebuffers (ap,KBUILD_MODNAME , false); +kfree (ap); + +return 0 ; +}static int radeonfb_pci_register (struct pci_dev *pdev,const struct pci_device_id *ent)@@ -2312,19 +2328,27 @@ static int radeonfb_pci_register(struct pci_dev *pdev, rinfo->fb_base_phys =pci_resource_start (pdev,0 ); rinfo->mmio_base_phys =pci_resource_start (pdev,2 ); + ret =radeon_kick_out_firmware_fb (pdev); +if (ret) +return ret; +/* request the mem regions */ ret =pci_request_region (pdev,0 ,"radeonfb framebuffer" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 0.\n" ,pci_name (rinfo->pdev)); goto err_release_fb; +#endif } ret =pci_request_region (pdev,2 ,"radeonfb mmio" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 2.\n" ,pci_name (rinfo->pdev)); goto err_release_pci0; +#endif }/* map the regions */ @@ -2509,10 +2533,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,iounmap (rinfo->mmio_base); err_release_pci2:pci_release_region (pdev,2 ); +#ifndef CONFIG_FB_OF err_release_pci0:pci_release_region (pdev,0 ); err_release_fb:framebuffer_release (info); +#endif err_disable: err_out:return ret;
Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
Hi,
Quoted 343 lines · Bartlomiej Zolnierkiewicz
Quoted 336 lines · Mathieu Malaterre
Bartlomiej,
Quoted 131 lines · Bartlomiej Zolnierkiewicz
Quoted 67 lines · Mathieu Malaterre
Bartlomiej,
Quoted 23 lines · Bartlomiej Zolnierkiewicz
Quoted 15 lines · Mathieu Malaterre
When the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=mThe offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16Quoted 5 lines
This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.
It should be noticed that
offb_destroyis never called which explain the need to skip error detection on the radeon side.Quoted 8 lines
This still needs to be explained more, from my last mail:
"The last
put_fb_info()onfb_infoshould call ->fb_destroy (offb_destroyin our case) andremove_conflicting_framebuffers()is callingput_fb_info()so there is some extra reference onfb_infosomewhere preventing it from going away.Please look into fixing this."
I am not familiar with the fb stuff internals but here is what I see:
# modprobe radeonfbleads to:
[ 52.058546] bus: 'pci': add driver radeonfb [ 52.058588] bus: 'pci': driver_probe_device: matched device 0000:00:10.0 with driver radeonfb [ 52.058595] bus: 'pci': really_probe: probing driver radeonfb with device 0000:00:10.0 [ 52.058608] devices_kset: Moving 0000:00:10.0 to end of list [ 52.058613] radeonfb_pci_register BEGIN [ 52.058634] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) <at this point radeon_kick_out_firmware_fb is called> [ 52.058666] checking generic (9c008000 96000) vs hw (98000000 8000000) [ 52.058667] fb: switching to radeonfb from OFfb ATY,RockHo [ 52.058844] Console: switching to colour dummy device 80x25 [ 52.058860] device: 'fb0': device_unregister [ 52.058956] PM: Removing info for No Bus:fb0 [ 52.059014] device: 'fb0': device_create_release <a call to do_unregister_framebuffer is done> <put_fb_info is done with a count=2 and dev=NULL> [ 52.059048] device: 'vtcon1': device_unregister [ 52.059076] PM: Removing info for No Bus:vtcon1 [ 52.059091] device: 'vtcon1': device_create_release [ 52.059107] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 52.256151] aper_base: 98000000 MC_FB_LOC to: 9bff9800, MC_AGP_LOC to: ffffa000 [ 52.256157] radeonfb (0000:00:10.0): Found 32768k of DDR 64 bitsQuoted 5 lines
wide videoram
I can confirm that
offb_destroyis never called (not sure exactly why), but in any case the call toradeon_kick_out_firmware_fbhappen much earlier, at least before theput_fb_info.It is okay,
put_fb_info()is called indirectly byradeon_kick_out_firmware_fb()
radeon_kick_out_firmware_fb()remove_conflicting_framebuffers() do_remove_conflicting_framebuffers() do_unregister_framebuffer() put_fb_info()
offb_destroy()is not called because there is an extra reference on oldfb_info(->count == 2):static void
put_fb_info(struct fb_info *fb_info){ if (!atomic_dec_and_test(&fb_info->count)) return; if (fb_info->fbops->fb_destroy) fb_info->fbops->fb_destroy(fb_info); }The question is why there is an extra reference, probably user-space is still holding the
fb_inforeference obtained infb_open()call andfb_release()is never called. Besides not callingfbops->fb_destroy()this also causes missing call offbops->fb_release()(infb_release()) which some fb drivers are implementing (but notoffb.c).Quoted 1 line
Could you describe a bit more the chain of calls you were thinking of ?
Please add
WARN_ON(1)toget_fb_info()andput_fb_info()so we can check from the stacktrace if it is actuallyfb_open()that holds the extra oldfb_inforeference.
drivers/video/fbdev/core/fbmem.c:static struct
fb_info*get_fb_info(unsigned int idx){ struct fb_info *fb_info; if (idx >= FB_MAX) return ERR_PTR(-ENODEV); mutex_lock(®istration_lock); fb_info = registered_fb[idx]; if (fb_info) atomic_inc(&fb_info->count);if (
fb_info)WARN_ON(1); mutex_unlock(®istration_lock); return fb_info; }static void
put_fb_info(struct fb_info *fb_info)
{WARN_ON(1);Quoted 5 lines
if (!atomic_dec_and_test(&fb_info->count)) return; if (fb_info->fbops->fb_destroy) fb_info->fbops->fb_destroy(fb_info); }Alright, here is what I see:
[ 18.961639] PM: Adding info for No Bus:vcs7 [ 18.966448] device: 'vcsa7': device_add [ 18.966496] PM: Adding info for No Bus:vcsa7 [ 19.001701] WARNING: CPU: 0 PID: 405 at drivers/video/fbdev/core/fbmem.c:68 get_fb_info.part.3+0x58/0x7c [ 19.001715] Modules linked in: uinput snd_aoa_codec_toonie
snd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 19.001773] CPU: 0 PID: 405 Comm: Xorg Not tainted 4.15.0+ #321 [ 19.001778] NIP: c039ef20 LR: c039eefc CTR: c039ef44 [ 19.001781] REGS: decc7c80 TRAP: 0700 Not tainted (4.15.0+) [ 19.001784] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 28222828 XER: 00000000 [ 19.001795] GPR00: c039eefc decc7d30 c147ab00 00000000 dc3ed8c0 df568a6c 00000001 c147ab00 GPR08: df568a6c 00000002 00000000 dc280c50 28222822 006f9ff4 006fff50 80000000 GPR16: 88000228 00000008 bfcb5b08 00000002 decc7e60 80000000 ffffffea 00000041 GPR24: 00000000 00000006 df568a6c dc3ed8c0 df5ef1e8 df568a40 c08f7c18 dc198800 [ 19.001835] NIP [c039ef20] get_fb_info.part.3+0x58/0x7c [ 19.001840] LR [c039eefc] get_fb_info.part.3+0x34/0x7c [ 19.001842] Call Trace: [ 19.001848] [decc7d30] [c039eefc] get_fb_info.part.3+0x34/0x7c (unreliable) [ 19.001854] [decc7d40] [c039efa0] fb_open+0x5c/0x18c [ 19.001866] [decc7d60] [c01e0e90] chrdev_open+0xb8/0x19c [ 19.001872] [decc7d90] [c01d7994] do_dentry_open+0x24c/0x398 [ 19.001881] [decc7dc0] [c01ec378] path_openat+0x4c4/0x11b8 [ 19.001888] [decc7e50] [c01ee0d8] do_filp_open+0xbc/0x10c [ 19.001893] [decc7f00] [c01d93b0] do_sys_open+0x158/0x228 [ 19.001901] [decc7f40] [c00181cc] ret_from_syscall+0x0/0x40 [ 19.001908] --- interrupt: c01 at 0xb751b940 LR = 0xb751b8dc [ 19.001912] Instruction dump: [ 19.001917] 7fc3f378 57ff103a 482cc171 3d20c093 39291a84 7fe9f82e 2f9f0000 419e0018 [ 19.001927] 7d20f828 31290001 7d20f92d 40a2fff4 <0fe00000> 7fc3f378 482cca69 7fe3fb78 [ 19.001938] ---[ end trace e0bf4192eb1c4f60 ]--- [ 19.001985] WARNING: CPU: 0 PID: 405 at drivers/video/fbdev/core/fbmem.c:77 put_fb_info+0x18/0x68 [ 19.001988] Modules linked in: uinput snd_aoa_codec_toonie
snd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 19.002028] CPU: 0 PID: 405 Comm: Xorg Tainted: G W 4.15.0+ #321 [ 19.002031] NIP: c039e6ec LR: c039eeb0 CTR: c039ee48 [ 19.002035] REGS: decc7e10 TRAP: 0700 Tainted: G W (4.15.0+) [ 19.002037] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 28000222 XER: 20000000 [ 19.002047] GPR00: c039eeb0 decc7ec0 c147ab00 dc198800 dc3ed8c0 dc3ed8c8 00000001 c147ab00 GPR08: 00000000 c08fa6f8 00000000 dc280c50 28000228 006f9ff4 006fff50 00000000 GPR16: 007001a8 00000008 bfcb5b08 007001a4 00000000 0070d0c4 00000002 00000000 GPR24: b6ad8b1c dc3ed8c8 df5ef1e8 df3e4ee0 dc280c50 df5ef1e8 dc19880c dc198800 [ 19.002086] NIP [c039e6ec] put_fb_info+0x18/0x68 [ 19.002091] LR [c039eeb0] fb_release+0x68/0x80 [ 19.002093] Call Trace: [ 19.002096] [decc7ec0] [df5ef1e8] 0xdf5ef1e8 (unreliable) [ 19.002102] [decc7ed0] [c039eeb0] fb_release+0x68/0x80 [ 19.002108] [decc7ee0] [c01dd2e8] __fput+0xb4/0x260 [ 19.002118] [decc7f10] [c006e088] task_work_run+0xc0/0xe8 [ 19.002129] [decc7f30] [c000aa90] do_notify_resume+0xb4/0xb8 [ 19.002135] [decc7f40] [c0018b4c] do_user_signal+0x7c/0xcc [ 19.002140] --- interrupt: c00 at 0xb751a7d8 LR = 0xb751a7ac [ 19.002144] Instruction dump: [ 19.002147] 80010014 38210010 7c0803a6 4e800020 38600000 4e800020 7c0802a6 90010004 [ 19.002157] 60000000 9421fff0 7c0802a6 90010014 <0fe00000> 7d401828 314affff 7d40192d [ 19.002168] ---[ end trace e0bf4192eb1c4f61 ]--- [ 19.002595] WARNING: CPU: 0 PID: 405 at drivers/video/fbdev/core/fbmem.c:68 get_fb_info.part.3+0x58/0x7c [ 19.002601] Modules linked in: uinput snd_aoa_codec_toonie
snd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 19.002645] CPU: 0 PID: 405 Comm: Xorg Tainted: G W 4.15.0+ #321 [ 19.002649] NIP: c039ef20 LR: c039eefc CTR: c039ef44 [ 19.002652] REGS: decc7c80 TRAP: 0700 Tainted: G W (4.15.0+) [ 19.002655] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 28222248 XER: 00000000 [ 19.002664] GPR00: c039eefc decc7d30 c147ab00 00000000 deca0340 deca0348 00000001 00000000 GPR08: 00000000 00000002 00000000 dc280c50 28222842 006f9ff4 006fff50 80000000 GPR16: 88000448 00000001 00000000 00000002 decc7e60 80000000 ffffffea 00000041 GPR24: 00000000 00000006 c01e0dd8 deca0340 df5ef1e8 df568a40 c08f7c18 dc198800 [ 19.002704] NIP [c039ef20] get_fb_info.part.3+0x58/0x7c [ 19.002708] LR [c039eefc] get_fb_info.part.3+0x34/0x7c [ 19.002711] Call Trace: [ 19.002716] [decc7d30] [c039eefc] get_fb_info.part.3+0x34/0x7c (unreliable) [ 19.002722] [decc7d40] [c039efa0] fb_open+0x5c/0x18c [ 19.002730] [decc7d60] [c01e0e90] chrdev_open+0xb8/0x19c [ 19.002735] [decc7d90] [c01d7994] do_dentry_open+0x24c/0x398 [ 19.002743] [decc7dc0] [c01ec378] path_openat+0x4c4/0x11b8 [ 19.002748] [decc7e50] [c01ee0d8] do_filp_open+0xbc/0x10c [ 19.002754] [decc7f00] [c01d93b0] do_sys_open+0x158/0x228 [ 19.002760] [decc7f40] [c00181cc] ret_from_syscall+0x0/0x40 [ 19.002766] --- interrupt: c01 at 0xb751b940 LR = 0xb751b8dc [ 19.002770] Instruction dump: [ 19.002774] 7fc3f378 57ff103a 482cc171 3d20c093 39291a84 7fe9f82e 2f9f0000 419e0018 [ 19.002784] 7d20f828 31290001 7d20f92d 40a2fff4 <0fe00000> 7fc3f378 482cca69 7fe3fb78 [ 19.002795] ---[ end trace e0bf4192eb1c4f62 ]--- [ 19.011629] gem 0002:20:0f.0 eth0: Link is up at 100 Mbps, full-duplex [ 19.011746] gem 0002:20:0f.0 eth0: Pause is disabled [ 19.011846] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 19.018954] device: 'input3': device_add [ 19.019031] PM: Adding info for No Bus:input3Then later on (after modprobe radeonfb):
[ 657.135105] PM: Removing info for No Bus:fb0 [ 657.135164] device: 'fb0': device_create_release [ 657.135279] WARNING: CPU: 0 PID: 475 at drivers/video/fbdev/core/fbmem.c:77 put_fb_info+0x18/0x68 [ 657.135284] Modules linked in: radeonfb(+) uinput
snd_aoa_codec_tooniesnd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 657.135344] CPU: 0 PID: 475 Comm: modprobe Tainted: G W 4.15.0+ #321 [ 657.135348] NIP: c039e6ec LR: c039e834 CTR: 00000000 [ 657.135352] REGS: dec93af0 TRAP: 0700 Tainted: G W (4.15.0+) [ 657.135355] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 24228822 XER: 20000000 [ 657.135365] GPR00: c039e834 dec93ba0 dc28eaa0 dc198800 00000000 000005c0 00000002 00000000 GPR08: 00001032 c08c2c2c 00000000 c08c1ab0 28228424 0049ce6c e2287b5c 00000000 GPR16: c06974dc 00000007 e2284384 00000001 dec9852c e2282610 00000000 000a0000 GPR24: c07c9d60 c07c9d2c dc19880c 00000000 dec93bb8 00000000 c0931a84 dc198800 [ 657.135405] NIP [c039e6ec] put_fb_info+0x18/0x68 [ 657.135411] LR [c039e834] do_unregister_framebuffer+0xf8/0x148 [ 657.135413] Call Trace: [ 657.135419] [dec93bb0] [c039e834] do_unregister_framebuffer+0xf8/0x148 [ 657.135425] [dec93be0] [c039ea1c] do_remove_conflicting_framebuffers+0x198/0x1b8 [ 657.135431] [dec93c30] [c039ea84] remove_conflicting_framebuffers+0x48/0x6c [ 657.135474] [dec93c50] [e2274d6c] radeonfb_pci_register+0x184/0x1838 [radeonfb] [ 657.135481] [dec93cb0] [c037e9fc] pci_device_probe+0x110/0x180 [ 657.135492] [dec93ce0] [c045be70] driver_probe_device+0x378/0x4a0 [ 657.135497] [dec93d10] [c045c0ac] __driver_attach+0x114/0x118 [ 657.135503] [dec93d30] [c04593dc] bus_for_each_dev+0x74/0xc0 [ 657.135508] [dec93d60] [c045acd4] bus_add_driver+0x18c/0x2a0 [ 657.135515] [dec93d80] [c045ce3c] driver_register+0x94/0x13c [ 657.135524] [dec93d90] [c0004af4] do_one_initcall+0x4c/0x178 [ 657.135536] [dec93df0] [c00ced18] do_init_module+0x70/0x1ec [ 657.135542] [dec93e10] [c00cdcb0] load_module+0x20d8/0x26b8 [ 657.135548] [dec93ec0] [c00ce500] SyS_finit_module+0xc4/0x120 [ 657.135555] [dec93f40] [c00181cc] ret_from_syscall+0x0/0x40 [ 657.135562] --- interrupt: c01 at 0x34d450 LR = 0x476108 [ 657.135566] Instruction dump: [ 657.135572] 80010014 38210010 7c0803a6 4e800020 38600000 4e800020 7c0802a6 90010004 [ 657.135582] 60000000 9421fff0 7c0802a6 90010014 <0fe00000> 7d401828 314affff 7d40192d [ 657.135593] ---[ end trace e0bf4192eb1c4f63 ]--- [ 657.135613] device: 'vtcon1': device_unregister [ 657.135644] PM: Removing info for No Bus:vtcon1Quoted 5 lines
Full dmesg:
https://people.debian.org/~malat/dmesg_radeonfb.txtDoes that help at all? the call stack does not make much sense to me. I am accessing the Mac Mini over ssh.
Quoted 6 lines
Thank you, it helps.
User-space is holding reference on the
/dev/fb0and oldfb_info(from offb) while offb is being replaced by radeonfb (this is why ->fb_destroy is never called). You may try checking with lsof command to see what is holding/dev/fb0open..
Right, I totally missed that X was running:
$ sudo lsof /dev/fb0 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME Xorg 469 root mem CHR 29,0 6500 /dev/fb0 Xorg 469 root 12u CHR 29,0 0t0 6500 /dev/fb0
so I simply:
$ dmesg > before_xdm_stop $ sudo service xdm stop $ dmesg > after_xdm_stop $ sudo lsof /dev/fb0 -> nothing
And I can verify in dmesg the call to put_fb_info:
$ diff -u before_xdm_stop after_xdm_stop @@ -1589,3 +1589,31 @@ [ 19.650088] gem 0002:20:0f.0 eth0: Link is up at 100 Mbps, full-duplex [ 19.650211] gem 0002:20:0f.0 eth0: Pause is disabled [ 19.650245] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready +[ 38.545478] WARNING: CPU: 0 PID: 468 at drivers/video/fbdev/core/fbmem.c:77 put_fb_info+0x18/0x68 +[ 38.545772] Modules linked in: uinput arc4 b43 bcma mac80211 snd_aoa_codec_toonie snd_aoa_fabric_layout snd_aoa sha256_generic cfg80211 evdev sg snd_aoa_i2sbus snd_aoa_soundbus snd_pcm snd_timer snd soundcore ssb usb_storage autofs4 ext4 crc16 mbcache jbd2 fscrypto usbhid ohci_pci ehci_pci ohci_hcd ehci_hcd sungem firewire_ohci sungem_phy firewire_core crc_itu_t sr_mod usbcore cdrom sd_mod nls_base usb_common +[ 38.546894] CPU: 0 PID: 468 Comm: Xorg Tainted: G W 4.15.0+ #31 +[ 38.547103] NIP: c03083ec LR: c0308bb0 CTR: c0308b48 +[ 38.547252] REGS: de661dc0 TRAP: 0700 Tainted: G W (4.15.0+) +[ 38.547459] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 22002222 XER: 20000000 +[ 38.547661] + GPR00: c0308bb0 de661e70 ddd108c0 dee02c00 de0febe0 de0febe8 00000001 ddd108c0 + GPR08: 00000000 c07b0a40 00000000 df501e10 22002428 007e0ff4 00000000 00000000 + GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 + GPR24: ddd108c0 de0febe8 dede1c10 df30bbb0 df501e10 dede1c10 dee02c10 dee02c00 +[ 38.548684] NIP [c03083ec] put_fb_info+0x18/0x68 +[ 38.548821] LR [c0308bb0] fb_release+0x68/0x80 +[ 38.548951] Call Trace: +[ 38.549026] [de661e70] [dede1c10] 0xdede1c10 (unreliable) +[ 38.549186] [de661e80] [c0308bb0] fb_release+0x68/0x80 +[ 38.549344] [de661e90] [c01c1198] __fput+0xac/0x20c +[ 38.553889] [de661ec0] [c0062140] task_work_run+0xc0/0xe8 +[ 38.558437] [de661ee0] [c0048918] do_exit+0x268/0x964 +[ 38.562960] [de661f20] [c00490b4] do_group_exit+0x4c/0xb0 +[ 38.567400] [de661f30] [c0049138] __wake_up_parent+0x0/0x3c +[ 38.571740] [de661f40] [c00151bc] ret_from_syscall+0x0/0x38 +[ 38.575965] --- interrupt: c01 at 0xb794a778 + LR = 0xb794a748 +[ 38.584039] Instruction dump: +[ 38.587878] 80010014 38210010 7c0803a6 4e800020 38600000 4e800020 7c0802a6 90010004 +[ 38.595537] 60000000 9421fff0 7c0802a6 90010014 <0fe00000> 7d401828 314affff 7d40192d +[ 38.603316] ---[ end trace ee2e036160cab00c ]---
Now with your WARN_ON patch and xdm service stopped, here is what I get:
https://people.debian.org/~malat/full_xdm_stop_offb_without.log
You'll see that modprobe to radeonfb still fails.
If you now compare with the patch (v4) applied (+ WARN_ON and xdm service stopped):
https://people.debian.org/~malat/full_xdm_stop_offb_with.log
You'll see a printk INFO for the call to offb_destroy:
...
[ 48.025983] MM calling offb_destroy
...
offb_destroy is called too late, which explains the failure for loading radeonfb without the patch.
-M
Quoted 95 lines
Quoted 88 lines
For reference, the patch I used is:
https://github.com/malaterre/linux/commit/89fd7d4438c5200a1a4fcba1d60dd701fda4f40e.patchQuoted 84 lines
Quoted 84 lines
Quoted 84 lines
Quoted 7 lines
Signed-off-by Mathieu Malaterre <[email protected]>Suggested-by Lennart Sorensen <[email protected]>---
v2: Only fails whenCONFIG_PCCis not set
v3: Only fails whenCONFIG_FB_OFis not set,CONFIG_PCCwas too broad. Since the conflicts in region is due to OFfb explicitly refers to it.It seems that there may still be configurations when this is incorrect -> when offb drives primary (non-radeon) card and radeonfb drives secondary (radeon) card..
Quoted 71 lines
drivers/video/fbdev/aty/radeon_base.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)drivers/video/fbdev/aty/radeon_base.c +26
-0@@ -2259,6 +2259,22 @@ static const struct bin_attribute edid2_attr = { .read = radeon_show_edid2, }; +static int radeon_kick_out_firmware_fb (struct pci_dev *pdev) +{ +struct apertures_struct *ap; + + ap =alloc_apertures (1 ); +if (!ap) +return -ENOMEM ; + + ap->ranges[0 ].base =pci_resource_start (pdev,0 ); + ap->ranges[0 ].size =pci_resource_len (pdev,0 ); + +remove_conflicting_framebuffers (ap,KBUILD_MODNAME , false); +kfree (ap); + +return 0 ; +}static int radeonfb_pci_register (struct pci_dev *pdev,const struct pci_device_id *ent)@@ -2312,19 +2328,27 @@ static int radeonfb_pci_register(struct pci_dev *pdev, rinfo->fb_base_phys =pci_resource_start (pdev,0 ); rinfo->mmio_base_phys =pci_resource_start (pdev,2 ); + ret =radeon_kick_out_firmware_fb (pdev); +if (ret) +return ret; +/* request the mem regions */ ret =pci_request_region (pdev,0 ,"radeonfb framebuffer" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 0.\n" ,pci_name (rinfo->pdev)); goto err_release_fb; +#endif } ret =pci_request_region (pdev,2 ,"radeonfb mmio" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 2.\n" ,pci_name (rinfo->pdev)); goto err_release_pci0; +#endif }/* map the regions */ @@ -2509,10 +2533,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,iounmap (rinfo->mmio_base); err_release_pci2:pci_release_region (pdev,2 ); +#ifndef CONFIG_FB_OF err_release_pci0:pci_release_region (pdev,0 ); err_release_fb:framebuffer_release (info); +#endif err_disable: err_out:return ret;Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
Quoted 432 lines · Mathieu Malaterre
Hi,
Quoted 343 lines · Bartlomiej Zolnierkiewicz
Quoted 336 lines · Mathieu Malaterre
Bartlomiej,
Quoted 131 lines · Bartlomiej Zolnierkiewicz
Quoted 67 lines · Mathieu Malaterre
Bartlomiej,
Quoted 23 lines · Bartlomiej Zolnierkiewicz
Quoted 15 lines · Mathieu Malaterre
When the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=mThe offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16Quoted 5 lines
This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.
It should be noticed that
offb_destroyis never called which explain the need to skip error detection on the radeon side.Quoted 8 lines
This still needs to be explained more, from my last mail:
"The last
put_fb_info()onfb_infoshould call ->fb_destroy (offb_destroyin our case) andremove_conflicting_framebuffers()is callingput_fb_info()so there is some extra reference onfb_infosomewhere preventing it from going away.Please look into fixing this."
I am not familiar with the fb stuff internals but here is what I see:
# modprobe radeonfbleads to:
[ 52.058546] bus: 'pci': add driver radeonfb [ 52.058588] bus: 'pci': driver_probe_device: matched device 0000:00:10.0 with driver radeonfb [ 52.058595] bus: 'pci': really_probe: probing driver radeonfb with device 0000:00:10.0 [ 52.058608] devices_kset: Moving 0000:00:10.0 to end of list [ 52.058613] radeonfb_pci_register BEGIN [ 52.058634] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) <at this point radeon_kick_out_firmware_fb is called> [ 52.058666] checking generic (9c008000 96000) vs hw (98000000 8000000) [ 52.058667] fb: switching to radeonfb from OFfb ATY,RockHo [ 52.058844] Console: switching to colour dummy device 80x25 [ 52.058860] device: 'fb0': device_unregister [ 52.058956] PM: Removing info for No Bus:fb0 [ 52.059014] device: 'fb0': device_create_release <a call to do_unregister_framebuffer is done> <put_fb_info is done with a count=2 and dev=NULL> [ 52.059048] device: 'vtcon1': device_unregister [ 52.059076] PM: Removing info for No Bus:vtcon1 [ 52.059091] device: 'vtcon1': device_create_release [ 52.059107] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 52.256151] aper_base: 98000000 MC_FB_LOC to: 9bff9800, MC_AGP_LOC to: ffffa000 [ 52.256157] radeonfb (0000:00:10.0): Found 32768k of DDR 64 bitsQuoted 5 lines
wide videoram
I can confirm that
offb_destroyis never called (not sure exactly why), but in any case the call toradeon_kick_out_firmware_fbhappen much earlier, at least before theput_fb_info.It is okay,
put_fb_info()is called indirectly byradeon_kick_out_firmware_fb()
radeon_kick_out_firmware_fb()remove_conflicting_framebuffers() do_remove_conflicting_framebuffers() do_unregister_framebuffer() put_fb_info()
offb_destroy()is not called because there is an extra reference on oldfb_info(->count == 2):static void
put_fb_info(struct fb_info *fb_info){ if (!atomic_dec_and_test(&fb_info->count)) return; if (fb_info->fbops->fb_destroy) fb_info->fbops->fb_destroy(fb_info); }The question is why there is an extra reference, probably user-space is still holding the
fb_inforeference obtained infb_open()call andfb_release()is never called. Besides not callingfbops->fb_destroy()this also causes missing call offbops->fb_release()(infb_release()) which some fb drivers are implementing (but notoffb.c).Quoted 1 line
Could you describe a bit more the chain of calls you were thinking of ?
Please add
WARN_ON(1)toget_fb_info()andput_fb_info()so we can check from the stacktrace if it is actuallyfb_open()that holds the extra oldfb_inforeference.
drivers/video/fbdev/core/fbmem.c:static struct
fb_info*get_fb_info(unsigned int idx){ struct fb_info *fb_info; if (idx >= FB_MAX) return ERR_PTR(-ENODEV); mutex_lock(®istration_lock); fb_info = registered_fb[idx]; if (fb_info) atomic_inc(&fb_info->count);if (
fb_info)WARN_ON(1); mutex_unlock(®istration_lock); return fb_info; }static void
put_fb_info(struct fb_info *fb_info)
{WARN_ON(1);Quoted 5 lines
if (!atomic_dec_and_test(&fb_info->count)) return; if (fb_info->fbops->fb_destroy) fb_info->fbops->fb_destroy(fb_info); }Alright, here is what I see:
[ 18.961639] PM: Adding info for No Bus:vcs7 [ 18.966448] device: 'vcsa7': device_add [ 18.966496] PM: Adding info for No Bus:vcsa7 [ 19.001701] WARNING: CPU: 0 PID: 405 at drivers/video/fbdev/core/fbmem.c:68 get_fb_info.part.3+0x58/0x7c [ 19.001715] Modules linked in: uinput snd_aoa_codec_toonie
snd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 19.001773] CPU: 0 PID: 405 Comm: Xorg Not tainted 4.15.0+ #321 [ 19.001778] NIP: c039ef20 LR: c039eefc CTR: c039ef44 [ 19.001781] REGS: decc7c80 TRAP: 0700 Not tainted (4.15.0+) [ 19.001784] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 28222828 XER: 00000000 [ 19.001795] GPR00: c039eefc decc7d30 c147ab00 00000000 dc3ed8c0 df568a6c 00000001 c147ab00 GPR08: df568a6c 00000002 00000000 dc280c50 28222822 006f9ff4 006fff50 80000000 GPR16: 88000228 00000008 bfcb5b08 00000002 decc7e60 80000000 ffffffea 00000041 GPR24: 00000000 00000006 df568a6c dc3ed8c0 df5ef1e8 df568a40 c08f7c18 dc198800 [ 19.001835] NIP [c039ef20] get_fb_info.part.3+0x58/0x7c [ 19.001840] LR [c039eefc] get_fb_info.part.3+0x34/0x7c [ 19.001842] Call Trace: [ 19.001848] [decc7d30] [c039eefc] get_fb_info.part.3+0x34/0x7c (unreliable) [ 19.001854] [decc7d40] [c039efa0] fb_open+0x5c/0x18c [ 19.001866] [decc7d60] [c01e0e90] chrdev_open+0xb8/0x19c [ 19.001872] [decc7d90] [c01d7994] do_dentry_open+0x24c/0x398 [ 19.001881] [decc7dc0] [c01ec378] path_openat+0x4c4/0x11b8 [ 19.001888] [decc7e50] [c01ee0d8] do_filp_open+0xbc/0x10c [ 19.001893] [decc7f00] [c01d93b0] do_sys_open+0x158/0x228 [ 19.001901] [decc7f40] [c00181cc] ret_from_syscall+0x0/0x40 [ 19.001908] --- interrupt: c01 at 0xb751b940 LR = 0xb751b8dc [ 19.001912] Instruction dump: [ 19.001917] 7fc3f378 57ff103a 482cc171 3d20c093 39291a84 7fe9f82e 2f9f0000 419e0018 [ 19.001927] 7d20f828 31290001 7d20f92d 40a2fff4 <0fe00000> 7fc3f378 482cca69 7fe3fb78 [ 19.001938] ---[ end trace e0bf4192eb1c4f60 ]--- [ 19.001985] WARNING: CPU: 0 PID: 405 at drivers/video/fbdev/core/fbmem.c:77 put_fb_info+0x18/0x68 [ 19.001988] Modules linked in: uinput snd_aoa_codec_toonie
snd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 19.002028] CPU: 0 PID: 405 Comm: Xorg Tainted: G W 4.15.0+ #321 [ 19.002031] NIP: c039e6ec LR: c039eeb0 CTR: c039ee48 [ 19.002035] REGS: decc7e10 TRAP: 0700 Tainted: G W (4.15.0+) [ 19.002037] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 28000222 XER: 20000000 [ 19.002047] GPR00: c039eeb0 decc7ec0 c147ab00 dc198800 dc3ed8c0 dc3ed8c8 00000001 c147ab00 GPR08: 00000000 c08fa6f8 00000000 dc280c50 28000228 006f9ff4 006fff50 00000000 GPR16: 007001a8 00000008 bfcb5b08 007001a4 00000000 0070d0c4 00000002 00000000 GPR24: b6ad8b1c dc3ed8c8 df5ef1e8 df3e4ee0 dc280c50 df5ef1e8 dc19880c dc198800 [ 19.002086] NIP [c039e6ec] put_fb_info+0x18/0x68 [ 19.002091] LR [c039eeb0] fb_release+0x68/0x80 [ 19.002093] Call Trace: [ 19.002096] [decc7ec0] [df5ef1e8] 0xdf5ef1e8 (unreliable) [ 19.002102] [decc7ed0] [c039eeb0] fb_release+0x68/0x80 [ 19.002108] [decc7ee0] [c01dd2e8] __fput+0xb4/0x260 [ 19.002118] [decc7f10] [c006e088] task_work_run+0xc0/0xe8 [ 19.002129] [decc7f30] [c000aa90] do_notify_resume+0xb4/0xb8 [ 19.002135] [decc7f40] [c0018b4c] do_user_signal+0x7c/0xcc [ 19.002140] --- interrupt: c00 at 0xb751a7d8 LR = 0xb751a7ac [ 19.002144] Instruction dump: [ 19.002147] 80010014 38210010 7c0803a6 4e800020 38600000 4e800020 7c0802a6 90010004 [ 19.002157] 60000000 9421fff0 7c0802a6 90010014 <0fe00000> 7d401828 314affff 7d40192d [ 19.002168] ---[ end trace e0bf4192eb1c4f61 ]--- [ 19.002595] WARNING: CPU: 0 PID: 405 at drivers/video/fbdev/core/fbmem.c:68 get_fb_info.part.3+0x58/0x7c [ 19.002601] Modules linked in: uinput snd_aoa_codec_toonie
snd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 19.002645] CPU: 0 PID: 405 Comm: Xorg Tainted: G W 4.15.0+ #321 [ 19.002649] NIP: c039ef20 LR: c039eefc CTR: c039ef44 [ 19.002652] REGS: decc7c80 TRAP: 0700 Tainted: G W (4.15.0+) [ 19.002655] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 28222248 XER: 00000000 [ 19.002664] GPR00: c039eefc decc7d30 c147ab00 00000000 deca0340 deca0348 00000001 00000000 GPR08: 00000000 00000002 00000000 dc280c50 28222842 006f9ff4 006fff50 80000000 GPR16: 88000448 00000001 00000000 00000002 decc7e60 80000000 ffffffea 00000041 GPR24: 00000000 00000006 c01e0dd8 deca0340 df5ef1e8 df568a40 c08f7c18 dc198800 [ 19.002704] NIP [c039ef20] get_fb_info.part.3+0x58/0x7c [ 19.002708] LR [c039eefc] get_fb_info.part.3+0x34/0x7c [ 19.002711] Call Trace: [ 19.002716] [decc7d30] [c039eefc] get_fb_info.part.3+0x34/0x7c (unreliable) [ 19.002722] [decc7d40] [c039efa0] fb_open+0x5c/0x18c [ 19.002730] [decc7d60] [c01e0e90] chrdev_open+0xb8/0x19c [ 19.002735] [decc7d90] [c01d7994] do_dentry_open+0x24c/0x398 [ 19.002743] [decc7dc0] [c01ec378] path_openat+0x4c4/0x11b8 [ 19.002748] [decc7e50] [c01ee0d8] do_filp_open+0xbc/0x10c [ 19.002754] [decc7f00] [c01d93b0] do_sys_open+0x158/0x228 [ 19.002760] [decc7f40] [c00181cc] ret_from_syscall+0x0/0x40 [ 19.002766] --- interrupt: c01 at 0xb751b940 LR = 0xb751b8dc [ 19.002770] Instruction dump: [ 19.002774] 7fc3f378 57ff103a 482cc171 3d20c093 39291a84 7fe9f82e 2f9f0000 419e0018 [ 19.002784] 7d20f828 31290001 7d20f92d 40a2fff4 <0fe00000> 7fc3f378 482cca69 7fe3fb78 [ 19.002795] ---[ end trace e0bf4192eb1c4f62 ]--- [ 19.011629] gem 0002:20:0f.0 eth0: Link is up at 100 Mbps, full-duplex [ 19.011746] gem 0002:20:0f.0 eth0: Pause is disabled [ 19.011846] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 19.018954] device: 'input3': device_add [ 19.019031] PM: Adding info for No Bus:input3Then later on (after modprobe radeonfb):
[ 657.135105] PM: Removing info for No Bus:fb0 [ 657.135164] device: 'fb0': device_create_release [ 657.135279] WARNING: CPU: 0 PID: 475 at drivers/video/fbdev/core/fbmem.c:77 put_fb_info+0x18/0x68 [ 657.135284] Modules linked in: radeonfb(+) uinput
snd_aoa_codec_tooniesnd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 657.135344] CPU: 0 PID: 475 Comm: modprobe Tainted: G W 4.15.0+ #321 [ 657.135348] NIP: c039e6ec LR: c039e834 CTR: 00000000 [ 657.135352] REGS: dec93af0 TRAP: 0700 Tainted: G W (4.15.0+) [ 657.135355] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 24228822 XER: 20000000 [ 657.135365] GPR00: c039e834 dec93ba0 dc28eaa0 dc198800 00000000 000005c0 00000002 00000000 GPR08: 00001032 c08c2c2c 00000000 c08c1ab0 28228424 0049ce6c e2287b5c 00000000 GPR16: c06974dc 00000007 e2284384 00000001 dec9852c e2282610 00000000 000a0000 GPR24: c07c9d60 c07c9d2c dc19880c 00000000 dec93bb8 00000000 c0931a84 dc198800 [ 657.135405] NIP [c039e6ec] put_fb_info+0x18/0x68 [ 657.135411] LR [c039e834] do_unregister_framebuffer+0xf8/0x148 [ 657.135413] Call Trace: [ 657.135419] [dec93bb0] [c039e834] do_unregister_framebuffer+0xf8/0x148 [ 657.135425] [dec93be0] [c039ea1c] do_remove_conflicting_framebuffers+0x198/0x1b8 [ 657.135431] [dec93c30] [c039ea84] remove_conflicting_framebuffers+0x48/0x6c [ 657.135474] [dec93c50] [e2274d6c] radeonfb_pci_register+0x184/0x1838 [radeonfb] [ 657.135481] [dec93cb0] [c037e9fc] pci_device_probe+0x110/0x180 [ 657.135492] [dec93ce0] [c045be70] driver_probe_device+0x378/0x4a0 [ 657.135497] [dec93d10] [c045c0ac] __driver_attach+0x114/0x118 [ 657.135503] [dec93d30] [c04593dc] bus_for_each_dev+0x74/0xc0 [ 657.135508] [dec93d60] [c045acd4] bus_add_driver+0x18c/0x2a0 [ 657.135515] [dec93d80] [c045ce3c] driver_register+0x94/0x13c [ 657.135524] [dec93d90] [c0004af4] do_one_initcall+0x4c/0x178 [ 657.135536] [dec93df0] [c00ced18] do_init_module+0x70/0x1ec [ 657.135542] [dec93e10] [c00cdcb0] load_module+0x20d8/0x26b8 [ 657.135548] [dec93ec0] [c00ce500] SyS_finit_module+0xc4/0x120 [ 657.135555] [dec93f40] [c00181cc] ret_from_syscall+0x0/0x40 [ 657.135562] --- interrupt: c01 at 0x34d450 LR = 0x476108 [ 657.135566] Instruction dump: [ 657.135572] 80010014 38210010 7c0803a6 4e800020 38600000 4e800020 7c0802a6 90010004 [ 657.135582] 60000000 9421fff0 7c0802a6 90010014 <0fe00000> 7d401828 314affff 7d40192d [ 657.135593] ---[ end trace e0bf4192eb1c4f63 ]--- [ 657.135613] device: 'vtcon1': device_unregister [ 657.135644] PM: Removing info for No Bus:vtcon1Quoted 5 lines
Full dmesg:
https://people.debian.org/~malat/dmesg_radeonfb.txtDoes that help at all? the call stack does not make much sense to me. I am accessing the Mac Mini over ssh.
Quoted 6 lines
Thank you, it helps.
User-space is holding reference on the
/dev/fb0and oldfb_info(from offb) while offb is being replaced by radeonfb (this is why ->fb_destroy is never called). You may try checking with lsof command to see what is holding/dev/fb0open..Right, I totally missed that X was running:
$ sudo lsof /dev/fb0 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME Xorg 469 root mem CHR 29,0 6500 /dev/fb0 Xorg 469 root 12u CHR 29,0 0t0 6500 /dev/fb0so I simply:
$ dmesg > before_xdm_stop $ sudo service xdm stop $ dmesg > after_xdm_stop $ sudo lsof /dev/fb0 -> nothingAnd I can verify in dmesg the call to
put_fb_info:$ diff -u before_xdm_stop after_xdm_stop(quoted diff) +1
-0@@ -1589,3 +1589,31 @@ [ 19.650088] gem 0002:20:0f.0 eth0: Link is up at 100 Mbps, full-duplex [ 19.650211] gem 0002:20:0f.0 eth0: Pause is disabled [ 19.650245] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready +[ 38.545478] WARNING: CPU: 0 PID: 468 at
drivers/video/fbdev/core/fbmem.c:77put_fb_info+0x18/0x68
+[ 38.545772] Modules linked in: uinput arc4 b43 bcma mac80211snd_aoa_codec_tooniesnd_aoa_fabric_layoutsnd_aoasha256_genericcfg80211 evdev sgsnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcore ssbusb_storageautofs4 ext4 crc16 mbcache jbd2 fscrypto usbhidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_phyfirewire_corecrc_itu_tsr_modusbcore cdromsd_modnls_baseusb_common
+[ 38.546894] CPU: 0 PID: 468 Comm: Xorg Tainted: G W
4.15.0+ #31
+[ 38.547103] NIP:c03083ecLR:c0308bb0CTR:c0308b48
+[ 38.547252] REGS:de661dc0TRAP: 0700 Tainted: G W
(4.15.0+)
+[ 38.547459] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 22002222 XER: 20000000
+[ 38.547661]
+ GPR00:c0308bb0de661e70ddd108c0dee02c00de0febe0de0febe800000001ddd108c0
+ GPR08: 00000000c07b0a4000000000df501e1022002428007e0ff400000000 00000000
+ GPR16: 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000
+ GPR24:ddd108c0de0febe8dede1c10df30bbb0df501e10dede1c10dee02c10dee02c00+[ 38.548684] NIP [c03083ec] put_fb_info+0x18/0x68 +[ 38.548821] LR [c0308bb0] fb_release+0x68/0x80 +[ 38.548951] Call Trace: +[ 38.549026] [de661e70] [dede1c10] 0xdede1c10 (unreliable) +[ 38.549186] [de661e80] [c0308bb0] fb_release+0x68/0x80 +[ 38.549344] [de661e90] [c01c1198] __fput+0xac/0x20c +[ 38.553889] [de661ec0] [c0062140] task_work_run+0xc0/0xe8 +[ 38.558437] [de661ee0] [c0048918] do_exit+0x268/0x964 +[ 38.562960] [de661f20] [c00490b4] do_group_exit+0x4c/0xb0 +[ 38.567400] [de661f30] [c0049138] __wake_up_parent+0x0/0x3c +[ 38.571740] [de661f40] [c00151bc] ret_from_syscall+0x0/0x38 +[ 38.575965] --- interrupt: c01 at 0xb794a778+ LR =
0xb794a748
+[ 38.584039] Instruction dump:
+[ 38.587878] 80010014 382100107c0803a64e800020386000004e8000207c0802a690010004
+[ 38.595537] 600000009421fff07c0802a690010014 <0fe00000>7d401828314affff7d40192d
+[ 38.603316] ---[ end traceee2e036160cab00c]---Now with your
WARN_ONpatch and xdm service stopped, here is what I get:https://people.debian.org/~malat/full_xdm_stop_offb_without.log
You'll see that modprobe to radeonfb still fails.
If you now compare with the patch (v4) applied (+
WARN_ONand xdm service stopped):https://people.debian.org/~malat/full_xdm_stop_offb_with.log
Quoted 8 lines
You'll see a printk INFO for the call to
offb_destroy:...
[ 48.025983] MM calling offb_destroy...
offb_destroyis called too late, which explains the failure for loading radeonfb without the patch.
offb_destroy() seems to be called in the right place but we still need to kick out offb. IOW your patch is needed but with xdm stop sequence it should be possible to drop ifdef hacks.
PS switch to drm_fb_helper_remove_conflicting_framebuffers() in v4 should be reverted to just use remove_conflicting_framebuffers() as the former one is for DRM subsystem only.
Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
Quoted 75 lines
-M
Quoted 73 lines
Quoted 73 lines
For reference, the patch I used is:
https://github.com/malaterre/linux/commit/89fd7d4438c5200a1a4fcba1d60dd701fda4f40e.patchQuoted 69 lines
Quoted 69 lines
Quoted 69 lines
Quoted 7 lines
Signed-off-by Mathieu Malaterre <[email protected]>Suggested-by Lennart Sorensen <[email protected]>---
v2: Only fails whenCONFIG_PCCis not set
v3: Only fails whenCONFIG_FB_OFis not set,CONFIG_PCCwas too broad. Since the conflicts in region is due to OFfb explicitly refers to it.It seems that there may still be configurations when this is incorrect -> when offb drives primary (non-radeon) card and radeonfb drives secondary (radeon) card..
Quoted 57 lines
drivers/video/fbdev/aty/radeon_base.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)drivers/video/fbdev/aty/radeon_base.c +24
-0@@ -2259,6 +2259,22 @@ static const struct bin_attribute edid2_attr = { .read = radeon_show_edid2, }; +static int radeon_kick_out_firmware_fb (struct pci_dev *pdev) +{ +struct apertures_struct *ap; + + ap =alloc_apertures (1 ); +if (!ap) +return -ENOMEM ; + + ap->ranges[0 ].base =pci_resource_start (pdev,0 ); + ap->ranges[0 ].size =pci_resource_len (pdev,0 ); + +remove_conflicting_framebuffers (ap,KBUILD_MODNAME , false); +kfree (ap); + +return 0 ; +}static int radeonfb_pci_register (struct pci_dev *pdev,const struct pci_device_id *ent)@@ -2312,19 +2328,27 @@ static int radeonfb_pci_register(struct pci_dev *pdev, rinfo->fb_base_phys =pci_resource_start (pdev,0 ); rinfo->mmio_base_phys =pci_resource_start (pdev,2 ); + ret =radeon_kick_out_firmware_fb (pdev); +if (ret) +return ret; +/* request the mem regions */ ret =pci_request_region (pdev,0 ,"radeonfb framebuffer" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 0.\n" ,pci_name (rinfo->pdev)); goto err_release_fb; +#endif } ret =pci_request_region (pdev,2 ,"radeonfb mmio" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 2.\n" ,pci_name (rinfo->pdev)); goto err_release_pci0; +#endif }
Quoted 14 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
drivers/video/fbdev/aty/radeon_base.c +1
-0/* map the regions */ @@ -2509,10 +2533,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,iounmap (rinfo->mmio_base); err_release_pci2:pci_release_region (pdev,2 ); +#ifndef CONFIG_FB_OF Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2544
Quoted 8 lines
drivers/video/fbdev/aty/radeon_base.c +1
-0err_release_pci0:pci_release_region (pdev,0 ); err_release_fb:framebuffer_release (info); +#endif err_disable: err_out:return ret;
Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
Quoted 439 lines · Bartlomiej Zolnierkiewicz
Quoted 438 lines · Mathieu Malaterre
Hi,
Quoted 343 lines · Bartlomiej Zolnierkiewicz
Quoted 336 lines · Mathieu Malaterre
Bartlomiej,
Quoted 131 lines · Bartlomiej Zolnierkiewicz
Quoted 67 lines · Mathieu Malaterre
Bartlomiej,
Quoted 23 lines · Bartlomiej Zolnierkiewicz
Quoted 15 lines · Mathieu Malaterre
When the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=mThe offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16Quoted 5 lines
This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded.
It should be noticed that
offb_destroyis never called which explain the need to skip error detection on the radeon side.Quoted 8 lines
This still needs to be explained more, from my last mail:
"The last
put_fb_info()onfb_infoshould call ->fb_destroy (offb_destroyin our case) andremove_conflicting_framebuffers()is callingput_fb_info()so there is some extra reference onfb_infosomewhere preventing it from going away.Please look into fixing this."
I am not familiar with the fb stuff internals but here is what I see:
# modprobe radeonfbleads to:
[ 52.058546] bus: 'pci': add driver radeonfb [ 52.058588] bus: 'pci': driver_probe_device: matched device 0000:00:10.0 with driver radeonfb [ 52.058595] bus: 'pci': really_probe: probing driver radeonfb with device 0000:00:10.0 [ 52.058608] devices_kset: Moving 0000:00:10.0 to end of list [ 52.058613] radeonfb_pci_register BEGIN [ 52.058634] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) <at this point radeon_kick_out_firmware_fb is called> [ 52.058666] checking generic (9c008000 96000) vs hw (98000000 8000000) [ 52.058667] fb: switching to radeonfb from OFfb ATY,RockHo [ 52.058844] Console: switching to colour dummy device 80x25 [ 52.058860] device: 'fb0': device_unregister [ 52.058956] PM: Removing info for No Bus:fb0 [ 52.059014] device: 'fb0': device_create_release <a call to do_unregister_framebuffer is done> <put_fb_info is done with a count=2 and dev=NULL> [ 52.059048] device: 'vtcon1': device_unregister [ 52.059076] PM: Removing info for No Bus:vtcon1 [ 52.059091] device: 'vtcon1': device_create_release [ 52.059107] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 52.256151] aper_base: 98000000 MC_FB_LOC to: 9bff9800, MC_AGP_LOC to: ffffa000 [ 52.256157] radeonfb (0000:00:10.0): Found 32768k of DDR 64 bitsQuoted 5 lines
wide videoram
I can confirm that
offb_destroyis never called (not sure exactly why), but in any case the call toradeon_kick_out_firmware_fbhappen much earlier, at least before theput_fb_info.It is okay,
put_fb_info()is called indirectly byradeon_kick_out_firmware_fb()
radeon_kick_out_firmware_fb()remove_conflicting_framebuffers() do_remove_conflicting_framebuffers() do_unregister_framebuffer() put_fb_info()
offb_destroy()is not called because there is an extra reference on oldfb_info(->count == 2):static void
put_fb_info(struct fb_info *fb_info){ if (!atomic_dec_and_test(&fb_info->count)) return; if (fb_info->fbops->fb_destroy) fb_info->fbops->fb_destroy(fb_info); }The question is why there is an extra reference, probably user-space is still holding the
fb_inforeference obtained infb_open()call andfb_release()is never called. Besides not callingfbops->fb_destroy()this also causes missing call offbops->fb_release()(infb_release()) which some fb drivers are implementing (but notoffb.c).Quoted 1 line
Could you describe a bit more the chain of calls you were thinking of ?
Please add
WARN_ON(1)toget_fb_info()andput_fb_info()so we can check from the stacktrace if it is actuallyfb_open()that holds the extra oldfb_inforeference.
drivers/video/fbdev/core/fbmem.c:static struct
fb_info*get_fb_info(unsigned int idx){ struct fb_info *fb_info; if (idx >= FB_MAX) return ERR_PTR(-ENODEV); mutex_lock(®istration_lock); fb_info = registered_fb[idx]; if (fb_info) atomic_inc(&fb_info->count);if (
fb_info)WARN_ON(1); mutex_unlock(®istration_lock); return fb_info; }static void
put_fb_info(struct fb_info *fb_info)
{WARN_ON(1);Quoted 5 lines
if (!atomic_dec_and_test(&fb_info->count)) return; if (fb_info->fbops->fb_destroy) fb_info->fbops->fb_destroy(fb_info); }Alright, here is what I see:
[ 18.961639] PM: Adding info for No Bus:vcs7 [ 18.966448] device: 'vcsa7': device_add [ 18.966496] PM: Adding info for No Bus:vcsa7 [ 19.001701] WARNING: CPU: 0 PID: 405 at drivers/video/fbdev/core/fbmem.c:68 get_fb_info.part.3+0x58/0x7c [ 19.001715] Modules linked in: uinput snd_aoa_codec_toonie
snd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 19.001773] CPU: 0 PID: 405 Comm: Xorg Not tainted 4.15.0+ #321 [ 19.001778] NIP: c039ef20 LR: c039eefc CTR: c039ef44 [ 19.001781] REGS: decc7c80 TRAP: 0700 Not tainted (4.15.0+) [ 19.001784] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 28222828 XER: 00000000 [ 19.001795] GPR00: c039eefc decc7d30 c147ab00 00000000 dc3ed8c0 df568a6c 00000001 c147ab00 GPR08: df568a6c 00000002 00000000 dc280c50 28222822 006f9ff4 006fff50 80000000 GPR16: 88000228 00000008 bfcb5b08 00000002 decc7e60 80000000 ffffffea 00000041 GPR24: 00000000 00000006 df568a6c dc3ed8c0 df5ef1e8 df568a40 c08f7c18 dc198800 [ 19.001835] NIP [c039ef20] get_fb_info.part.3+0x58/0x7c [ 19.001840] LR [c039eefc] get_fb_info.part.3+0x34/0x7c [ 19.001842] Call Trace: [ 19.001848] [decc7d30] [c039eefc] get_fb_info.part.3+0x34/0x7c (unreliable) [ 19.001854] [decc7d40] [c039efa0] fb_open+0x5c/0x18c [ 19.001866] [decc7d60] [c01e0e90] chrdev_open+0xb8/0x19c [ 19.001872] [decc7d90] [c01d7994] do_dentry_open+0x24c/0x398 [ 19.001881] [decc7dc0] [c01ec378] path_openat+0x4c4/0x11b8 [ 19.001888] [decc7e50] [c01ee0d8] do_filp_open+0xbc/0x10c [ 19.001893] [decc7f00] [c01d93b0] do_sys_open+0x158/0x228 [ 19.001901] [decc7f40] [c00181cc] ret_from_syscall+0x0/0x40 [ 19.001908] --- interrupt: c01 at 0xb751b940 LR = 0xb751b8dc [ 19.001912] Instruction dump: [ 19.001917] 7fc3f378 57ff103a 482cc171 3d20c093 39291a84 7fe9f82e 2f9f0000 419e0018 [ 19.001927] 7d20f828 31290001 7d20f92d 40a2fff4 <0fe00000> 7fc3f378 482cca69 7fe3fb78 [ 19.001938] ---[ end trace e0bf4192eb1c4f60 ]--- [ 19.001985] WARNING: CPU: 0 PID: 405 at drivers/video/fbdev/core/fbmem.c:77 put_fb_info+0x18/0x68 [ 19.001988] Modules linked in: uinput snd_aoa_codec_toonie
snd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 19.002028] CPU: 0 PID: 405 Comm: Xorg Tainted: G W 4.15.0+ #321 [ 19.002031] NIP: c039e6ec LR: c039eeb0 CTR: c039ee48 [ 19.002035] REGS: decc7e10 TRAP: 0700 Tainted: G W (4.15.0+) [ 19.002037] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 28000222 XER: 20000000 [ 19.002047] GPR00: c039eeb0 decc7ec0 c147ab00 dc198800 dc3ed8c0 dc3ed8c8 00000001 c147ab00 GPR08: 00000000 c08fa6f8 00000000 dc280c50 28000228 006f9ff4 006fff50 00000000 GPR16: 007001a8 00000008 bfcb5b08 007001a4 00000000 0070d0c4 00000002 00000000 GPR24: b6ad8b1c dc3ed8c8 df5ef1e8 df3e4ee0 dc280c50 df5ef1e8 dc19880c dc198800 [ 19.002086] NIP [c039e6ec] put_fb_info+0x18/0x68 [ 19.002091] LR [c039eeb0] fb_release+0x68/0x80 [ 19.002093] Call Trace: [ 19.002096] [decc7ec0] [df5ef1e8] 0xdf5ef1e8 (unreliable) [ 19.002102] [decc7ed0] [c039eeb0] fb_release+0x68/0x80 [ 19.002108] [decc7ee0] [c01dd2e8] __fput+0xb4/0x260 [ 19.002118] [decc7f10] [c006e088] task_work_run+0xc0/0xe8 [ 19.002129] [decc7f30] [c000aa90] do_notify_resume+0xb4/0xb8 [ 19.002135] [decc7f40] [c0018b4c] do_user_signal+0x7c/0xcc [ 19.002140] --- interrupt: c00 at 0xb751a7d8 LR = 0xb751a7ac [ 19.002144] Instruction dump: [ 19.002147] 80010014 38210010 7c0803a6 4e800020 38600000 4e800020 7c0802a6 90010004 [ 19.002157] 60000000 9421fff0 7c0802a6 90010014 <0fe00000> 7d401828 314affff 7d40192d [ 19.002168] ---[ end trace e0bf4192eb1c4f61 ]--- [ 19.002595] WARNING: CPU: 0 PID: 405 at drivers/video/fbdev/core/fbmem.c:68 get_fb_info.part.3+0x58/0x7c [ 19.002601] Modules linked in: uinput snd_aoa_codec_toonie
snd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 19.002645] CPU: 0 PID: 405 Comm: Xorg Tainted: G W 4.15.0+ #321 [ 19.002649] NIP: c039ef20 LR: c039eefc CTR: c039ef44 [ 19.002652] REGS: decc7c80 TRAP: 0700 Tainted: G W (4.15.0+) [ 19.002655] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 28222248 XER: 00000000 [ 19.002664] GPR00: c039eefc decc7d30 c147ab00 00000000 deca0340 deca0348 00000001 00000000 GPR08: 00000000 00000002 00000000 dc280c50 28222842 006f9ff4 006fff50 80000000 GPR16: 88000448 00000001 00000000 00000002 decc7e60 80000000 ffffffea 00000041 GPR24: 00000000 00000006 c01e0dd8 deca0340 df5ef1e8 df568a40 c08f7c18 dc198800 [ 19.002704] NIP [c039ef20] get_fb_info.part.3+0x58/0x7c [ 19.002708] LR [c039eefc] get_fb_info.part.3+0x34/0x7c [ 19.002711] Call Trace: [ 19.002716] [decc7d30] [c039eefc] get_fb_info.part.3+0x34/0x7c (unreliable) [ 19.002722] [decc7d40] [c039efa0] fb_open+0x5c/0x18c [ 19.002730] [decc7d60] [c01e0e90] chrdev_open+0xb8/0x19c [ 19.002735] [decc7d90] [c01d7994] do_dentry_open+0x24c/0x398 [ 19.002743] [decc7dc0] [c01ec378] path_openat+0x4c4/0x11b8 [ 19.002748] [decc7e50] [c01ee0d8] do_filp_open+0xbc/0x10c [ 19.002754] [decc7f00] [c01d93b0] do_sys_open+0x158/0x228 [ 19.002760] [decc7f40] [c00181cc] ret_from_syscall+0x0/0x40 [ 19.002766] --- interrupt: c01 at 0xb751b940 LR = 0xb751b8dc [ 19.002770] Instruction dump: [ 19.002774] 7fc3f378 57ff103a 482cc171 3d20c093 39291a84 7fe9f82e 2f9f0000 419e0018 [ 19.002784] 7d20f828 31290001 7d20f92d 40a2fff4 <0fe00000> 7fc3f378 482cca69 7fe3fb78 [ 19.002795] ---[ end trace e0bf4192eb1c4f62 ]--- [ 19.011629] gem 0002:20:0f.0 eth0: Link is up at 100 Mbps, full-duplex [ 19.011746] gem 0002:20:0f.0 eth0: Pause is disabled [ 19.011846] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 19.018954] device: 'input3': device_add [ 19.019031] PM: Adding info for No Bus:input3Then later on (after modprobe radeonfb):
[ 657.135105] PM: Removing info for No Bus:fb0 [ 657.135164] device: 'fb0': device_create_release [ 657.135279] WARNING: CPU: 0 PID: 475 at drivers/video/fbdev/core/fbmem.c:77 put_fb_info+0x18/0x68 [ 657.135284] Modules linked in: radeonfb(+) uinput
snd_aoa_codec_tooniesnd_aoa_fabric_layoutsnd_aoasnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcorerack_meterevdevi2c_devsgusb_storageip_tablesx_tablesautofs4 ext4 crc16 mbcache jbd2 fscryptohid_genericusbhid hidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_physr_modfirewire_corecrc_itu_tcdromsd_modusbcore[ 657.135344] CPU: 0 PID: 475 Comm: modprobe Tainted: G W 4.15.0+ #321 [ 657.135348] NIP: c039e6ec LR: c039e834 CTR: 00000000 [ 657.135352] REGS: dec93af0 TRAP: 0700 Tainted: G W (4.15.0+) [ 657.135355] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 24228822 XER: 20000000 [ 657.135365] GPR00: c039e834 dec93ba0 dc28eaa0 dc198800 00000000 000005c0 00000002 00000000 GPR08: 00001032 c08c2c2c 00000000 c08c1ab0 28228424 0049ce6c e2287b5c 00000000 GPR16: c06974dc 00000007 e2284384 00000001 dec9852c e2282610 00000000 000a0000 GPR24: c07c9d60 c07c9d2c dc19880c 00000000 dec93bb8 00000000 c0931a84 dc198800 [ 657.135405] NIP [c039e6ec] put_fb_info+0x18/0x68 [ 657.135411] LR [c039e834] do_unregister_framebuffer+0xf8/0x148 [ 657.135413] Call Trace: [ 657.135419] [dec93bb0] [c039e834] do_unregister_framebuffer+0xf8/0x148 [ 657.135425] [dec93be0] [c039ea1c] do_remove_conflicting_framebuffers+0x198/0x1b8 [ 657.135431] [dec93c30] [c039ea84] remove_conflicting_framebuffers+0x48/0x6c [ 657.135474] [dec93c50] [e2274d6c] radeonfb_pci_register+0x184/0x1838 [radeonfb] [ 657.135481] [dec93cb0] [c037e9fc] pci_device_probe+0x110/0x180 [ 657.135492] [dec93ce0] [c045be70] driver_probe_device+0x378/0x4a0 [ 657.135497] [dec93d10] [c045c0ac] __driver_attach+0x114/0x118 [ 657.135503] [dec93d30] [c04593dc] bus_for_each_dev+0x74/0xc0 [ 657.135508] [dec93d60] [c045acd4] bus_add_driver+0x18c/0x2a0 [ 657.135515] [dec93d80] [c045ce3c] driver_register+0x94/0x13c [ 657.135524] [dec93d90] [c0004af4] do_one_initcall+0x4c/0x178 [ 657.135536] [dec93df0] [c00ced18] do_init_module+0x70/0x1ec [ 657.135542] [dec93e10] [c00cdcb0] load_module+0x20d8/0x26b8 [ 657.135548] [dec93ec0] [c00ce500] SyS_finit_module+0xc4/0x120 [ 657.135555] [dec93f40] [c00181cc] ret_from_syscall+0x0/0x40 [ 657.135562] --- interrupt: c01 at 0x34d450 LR = 0x476108 [ 657.135566] Instruction dump: [ 657.135572] 80010014 38210010 7c0803a6 4e800020 38600000 4e800020 7c0802a6 90010004 [ 657.135582] 60000000 9421fff0 7c0802a6 90010014 <0fe00000> 7d401828 314affff 7d40192d [ 657.135593] ---[ end trace e0bf4192eb1c4f63 ]--- [ 657.135613] device: 'vtcon1': device_unregister [ 657.135644] PM: Removing info for No Bus:vtcon1Quoted 5 lines
Full dmesg:
https://people.debian.org/~malat/dmesg_radeonfb.txtDoes that help at all? the call stack does not make much sense to me. I am accessing the Mac Mini over ssh.
Quoted 6 lines
Thank you, it helps.
User-space is holding reference on the
/dev/fb0and oldfb_info(from offb) while offb is being replaced by radeonfb (this is why ->fb_destroy is never called). You may try checking with lsof command to see what is holding/dev/fb0open..Right, I totally missed that X was running:
$ sudo lsof /dev/fb0 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME Xorg 469 root mem CHR 29,0 6500 /dev/fb0 Xorg 469 root 12u CHR 29,0 0t0 6500 /dev/fb0so I simply:
$ dmesg > before_xdm_stop $ sudo service xdm stop $ dmesg > after_xdm_stop $ sudo lsof /dev/fb0 -> nothingAnd I can verify in dmesg the call to
put_fb_info:$ diff -u before_xdm_stop after_xdm_stop(quoted diff) +1
-0@@ -1589,3 +1589,31 @@ [ 19.650088] gem 0002:20:0f.0 eth0: Link is up at 100 Mbps, full-duplex [ 19.650211] gem 0002:20:0f.0 eth0: Pause is disabled [ 19.650245] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready +[ 38.545478] WARNING: CPU: 0 PID: 468 at
drivers/video/fbdev/core/fbmem.c:77put_fb_info+0x18/0x68
+[ 38.545772] Modules linked in: uinput arc4 b43 bcma mac80211snd_aoa_codec_tooniesnd_aoa_fabric_layoutsnd_aoasha256_genericcfg80211 evdev sgsnd_aoa_i2sbussnd_aoa_soundbussnd_pcmsnd_timersnd soundcore ssbusb_storageautofs4 ext4 crc16 mbcache jbd2 fscrypto usbhidohci_pciehci_pciohci_hcdehci_hcdsungemfirewire_ohcisungem_phyfirewire_corecrc_itu_tsr_modusbcore cdromsd_modnls_baseusb_common
+[ 38.546894] CPU: 0 PID: 468 Comm: Xorg Tainted: G W
4.15.0+ #31
+[ 38.547103] NIP:c03083ecLR:c0308bb0CTR:c0308b48
+[ 38.547252] REGS:de661dc0TRAP: 0700 Tainted: G W
(4.15.0+)
+[ 38.547459] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 22002222 XER: 20000000
+[ 38.547661]
+ GPR00:c0308bb0de661e70ddd108c0dee02c00de0febe0de0febe800000001ddd108c0
+ GPR08: 00000000c07b0a4000000000df501e1022002428007e0ff400000000 00000000
+ GPR16: 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000
+ GPR24:ddd108c0de0febe8dede1c10df30bbb0df501e10dede1c10dee02c10dee02c00+[ 38.548684] NIP [c03083ec] put_fb_info+0x18/0x68 +[ 38.548821] LR [c0308bb0] fb_release+0x68/0x80 +[ 38.548951] Call Trace: +[ 38.549026] [de661e70] [dede1c10] 0xdede1c10 (unreliable) +[ 38.549186] [de661e80] [c0308bb0] fb_release+0x68/0x80 +[ 38.549344] [de661e90] [c01c1198] __fput+0xac/0x20c +[ 38.553889] [de661ec0] [c0062140] task_work_run+0xc0/0xe8 +[ 38.558437] [de661ee0] [c0048918] do_exit+0x268/0x964 +[ 38.562960] [de661f20] [c00490b4] do_group_exit+0x4c/0xb0 +[ 38.567400] [de661f30] [c0049138] __wake_up_parent+0x0/0x3c +[ 38.571740] [de661f40] [c00151bc] ret_from_syscall+0x0/0x38 +[ 38.575965] --- interrupt: c01 at 0xb794a778+ LR =
0xb794a748
+[ 38.584039] Instruction dump:
+[ 38.587878] 80010014 382100107c0803a64e800020386000004e8000207c0802a690010004
+[ 38.595537] 600000009421fff07c0802a690010014 <0fe00000>7d401828314affff7d40192d
+[ 38.603316] ---[ end traceee2e036160cab00c]---Now with your
WARN_ONpatch and xdm service stopped, here is what I get:https://people.debian.org/~malat/full_xdm_stop_offb_without.log
You'll see that modprobe to radeonfb still fails.
If you now compare with the patch (v4) applied (+
WARN_ONand xdm service stopped):https://people.debian.org/~malat/full_xdm_stop_offb_with.log
You'll see a printk INFO for the call to
offb_destroy:...
[ 48.025983] MM calling offb_destroy...
Quoted 6 lines
Quoted 2 lines
offb_destroyis called too late, which explains the failure for loading radeonfb without the patch.
offb_destroy()seems to be called in the right place but we still need to kick out offb. IOW your patch is needed but with xdm stop sequence it should be possible to drop ifdef hacks.
/facepalm/ I can't believe the solution was in front of me from day one.
Quoted 3 lines
PS switch to
drm_fb_helper_remove_conflicting_framebuffers()in v4 should be reverted to just useremove_conflicting_framebuffers()as the former one is for DRM subsystem only.
Ah, great ! Thanks for the clarification. v5 sent.
Thanks much !
Quoted 102 lines
Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung ElectronicsQuoted 75 lines
-M
Quoted 73 lines
Quoted 73 lines
For reference, the patch I used is:
https://github.com/malaterre/linux/commit/89fd7d4438c5200a1a4fcba1d60dd701fda4f40e.patchQuoted 69 lines
Quoted 69 lines
Quoted 69 lines
Quoted 7 lines
Signed-off-by Mathieu Malaterre <[email protected]>Suggested-by Lennart Sorensen <[email protected]>---
v2: Only fails whenCONFIG_PCCis not set
v3: Only fails whenCONFIG_FB_OFis not set,CONFIG_PCCwas too broad. Since the conflicts in region is due to OFfb explicitly refers to it.It seems that there may still be configurations when this is incorrect -> when offb drives primary (non-radeon) card and radeonfb drives secondary (radeon) card..
Quoted 57 lines
drivers/video/fbdev/aty/radeon_base.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)drivers/video/fbdev/aty/radeon_base.c +24
-0@@ -2259,6 +2259,22 @@ static const struct bin_attribute edid2_attr = { .read = radeon_show_edid2, }; +static int radeon_kick_out_firmware_fb (struct pci_dev *pdev) +{ +struct apertures_struct *ap; + + ap =alloc_apertures (1 ); +if (!ap) +return -ENOMEM ; + + ap->ranges[0 ].base =pci_resource_start (pdev,0 ); + ap->ranges[0 ].size =pci_resource_len (pdev,0 ); + +remove_conflicting_framebuffers (ap,KBUILD_MODNAME , false); +kfree (ap); + +return 0 ; +}static int radeonfb_pci_register (struct pci_dev *pdev,const struct pci_device_id *ent)@@ -2312,19 +2328,27 @@ static int radeonfb_pci_register(struct pci_dev *pdev, rinfo->fb_base_phys =pci_resource_start (pdev,0 ); rinfo->mmio_base_phys =pci_resource_start (pdev,2 ); + ret =radeon_kick_out_firmware_fb (pdev); +if (ret) +return ret; +/* request the mem regions */ ret =pci_request_region (pdev,0 ,"radeonfb framebuffer" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 0.\n" ,pci_name (rinfo->pdev)); goto err_release_fb; +#endif } ret =pci_request_region (pdev,2 ,"radeonfb mmio" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 2.\n" ,pci_name (rinfo->pdev)); goto err_release_pci0; +#endif }Quoted 14 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
drivers/video/fbdev/aty/radeon_base.c +1
-0/* map the regions */ @@ -2509,10 +2533,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,iounmap (rinfo->mmio_base); err_release_pci2:pci_release_region (pdev,2 ); +#ifndef CONFIG_FB_OF Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
drivers/video/fbdev/aty/radeon_base.c static int radeonfb_pci_register(struct pci_dev *pdev, · line 2544
Quoted 8 lines
drivers/video/fbdev/aty/radeon_base.c +1
-0err_release_pci0:pci_release_region (pdev,0 ); err_release_fb:framebuffer_release (info); +#endif err_disable: err_out:return ret;Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
PATCH v4 1/1 Fix loading of module radeonfb on PowerMac
In reply to Mathieu MalaterreWhen the linux kernel is build with (typical kernel ship with Debian installer):
CONFIG_FB_OF=yCONFIG_VT_HW_CONSOLE_BINDING=yCONFIG_FB_RADEON=m
The offb driver takes precedence over module radeonfb. It is then impossible to load the module, error reported is:
[ 96.551486] radeonfb 0000:00:10.0: enabling device (0006 -> 0007) [ 96.551526] radeonfb 0000:00:10.0: BAR 0: can't reserve [mem 0x98000000-0x9fffffff pref] [ 96.551531] radeonfb (0000:00:10.0): cannot request region 0. [ 96.551545] radeonfb: probe of 0000:00:10.0 failed with error -16
This patch reproduce the behavior of the module radeon, so as to make it possible to load radeonfb when offb is first loaded, see commit a56f7428d753 ("drm/radeon: Add early unregister of firmware fb's").
It should be noticed that offb_destroy is never called which explain the need to skip error detection on the radeon side.
---
v2: Only fails when CONFIG_PCC is not set
v3: Only fails when CONFIG_FB_OF is not set, CONFIG_PCC was too broad. Since the conflicts in region is due to OFfb explicitly refers to it.
v4: Use drm_fb_helper_remove_conflicting_framebuffers from drm_fb_helper
drivers/video/fbdev/aty/radeon_base.c | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+)
drivers/video/fbdev/aty/radeon_base.c +28 -0
@@ -70,6 +70,7 @@#include <linux/pci.h> #include <linux/vmalloc.h> #include <linux/device.h> +#include <drm/drm_fb_helper.h> #include <asm/io.h> #include <linux/uaccess.h>
@@ -2259,6 +2260,23 @@ static const struct bin_attribute edid2_attr = { .read = radeon_show_edid2, }; +static int radeon_kick_out_firmware_fb (struct pci_dev *pdev) +{ +struct apertures_struct *ap; + + ap =alloc_apertures (1 ); +if (!ap) +return -ENOMEM ; + + ap->ranges[0 ].base =pci_resource_start (pdev,0 ); + ap->ranges[0 ].size =pci_resource_len (pdev,0 ); + +drm_fb_helper_remove_conflicting_framebuffers (ap,KBUILD_MODNAME , false); + +kfree (ap); + +return 0 ; +}static int radeonfb_pci_register (struct pci_dev *pdev,const struct pci_device_id *ent)
@@ -2312,19 +2330,27 @@ static int radeonfb_pci_register(struct pci_dev *pdev, rinfo->fb_base_phys =pci_resource_start (pdev,0 ); rinfo->mmio_base_phys =pci_resource_start (pdev,2 ); + ret =radeon_kick_out_firmware_fb (pdev); +if (ret) +return ret; +/* request the mem regions */ ret =pci_request_region (pdev,0 ,"radeonfb framebuffer" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 0.\n" ,pci_name (rinfo->pdev)); goto err_release_fb; +#endif } ret =pci_request_region (pdev,2 ,"radeonfb mmio" );if (ret <0 ) { +#ifndef CONFIG_FB_OF printk (KERN_ERR "radeonfb (%s): cannot request region 2.\n" ,pci_name (rinfo->pdev)); goto err_release_pci0; +#endif }/* map the regions */
@@ -2509,10 +2535,12 @@ static int radeonfb_pci_register(struct pci_dev *pdev,iounmap (rinfo->mmio_base); err_release_pci2:pci_release_region (pdev,2 ); +#ifndef CONFIG_FB_OF err_release_pci0:pci_release_region (pdev,0 ); err_release_fb:framebuffer_release (info); +#endif err_disable: err_out:return ret;
Signature · 1 line
2.11.0
kbuild test robot
build botThank you for the patch! Perhaps something to improve:
Hi Mathieu,
Thank you for the patch! Perhaps something to improve:
[auto build test WARNING on linus/master]
[also build test WARNING on v4.15 next-20180202]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Mathieu-Malaterre/Fix-loading-of-module-radeonfb-on-PowerMac/20180203-085907
config: x86_64-randconfig-x009-201804 (attached as .config)
compiler: gcc-7 (Debian 7.2.0-12) 7.2.1 20171025 reproduce:
# save the attached .config to linux build tree
make ARCH=x86_64 All warnings (new ones prefixed by >>):
In file included from drivers/video/fbdev/aty/radeon_base.c:91:0:
>> drivers/video/fbdev/aty/../edid.h:21:0: warning: "EDID_LENGTH" redefined
#define EDID_LENGTH 0x80 In file included from include/drm/drm_crtc.h:44:0,
from include/drm/drm_fb_helper.h:35,
from drivers/video/fbdev/aty/radeon_base.c:73:
include/drm/drm_edid.h:32:0: note: this is the location of the previous definition
#define EDID_LENGTH 128
Cyclomatic Complexity 1 arch/x86/include/asm/bitops.h:fls64
Cyclomatic Complexity 1 include/linux/log2.h:__ilog2_u64
Cyclomatic Complexity 1 include/asm-generic/getorder.h:__get_order
Cyclomatic Complexity 1 include/linux/string.h:strnlen
Cyclomatic Complexity 4 include/linux/string.h:strlen
Cyclomatic Complexity 6 include/linux/string.h:strlcpy
Cyclomatic Complexity 4 include/linux/string.h:memcpy
Cyclomatic Complexity 1 arch/x86/include/asm/paravirt.h:arch_local_irq_disable Cyclomatic Complexity 1 arch/x86/include/asm/paravirt.h:arch_local_irq_enable Cyclomatic Complexity 1 include/linux/spinlock.h:spinlock_check
Cyclomatic Complexity 1 include/linux/spinlock.h:spin_unlock_irqrestore Cyclomatic Complexity 1 include/linux/jiffies.h:_msecs_to_jiffies
Cyclomatic Complexity 3 include/linux/jiffies.h:msecs_to_jiffies
Cyclomatic Complexity 1 arch/x86/include/asm/io.h:readb
Cyclomatic Complexity 1 arch/x86/include/asm/io.h:readw
Cyclomatic Complexity 1 arch/x86/include/asm/io.h:readl
Cyclomatic Complexity 1 arch/x86/include/asm/io.h:writeb
Cyclomatic Complexity 1 arch/x86/include/asm/io.h:writel
Cyclomatic Complexity 1 arch/x86/include/asm/io.h:ioremap
Cyclomatic Complexity 1 include/linux/kobject.h:kobject_name
Cyclomatic Complexity 2 include/linux/device.h:dev_name
Cyclomatic Complexity 1 include/linux/device.h:dev_get_drvdata
Cyclomatic Complexity 1 include/linux/device.h:dev_set_drvdata
Cyclomatic Complexity 1 include/linux/io.h:arch_phys_wc_add
Cyclomatic Complexity 1 include/linux/io.h:arch_phys_wc_del
Cyclomatic Complexity 68 include/linux/slab.h:kmalloc_large
Cyclomatic Complexity 3 include/linux/slab.h:kmalloc
Cyclomatic Complexity 1 include/linux/slab.h:kzalloc
Cyclomatic Complexity 1 include/linux/pci.h:pci_get_drvdata
Cyclomatic Complexity 1 include/linux/pci.h:pci_set_drvdata
Cyclomatic Complexity 1 include/linux/pci.h:pci_name
Cyclomatic Complexity 2 include/linux/fb.h:alloc_apertures
Cyclomatic Complexity 2 drivers/video/fbdev/aty/radeonfb.h:radeon_pll_errata_after_index Cyclomatic Complexity 2 drivers/video/fbdev/aty/radeonfb.h:radeon_pll_errata_after_data Cyclomatic Complexity 1 drivers/video/fbdev/aty/radeonfb.h:round_div
Cyclomatic Complexity 3 drivers/video/fbdev/aty/radeonfb.h:var_to_depth Cyclomatic Complexity 5 drivers/video/fbdev/aty/radeonfb.h:radeon_get_dstbpp Cyclomatic Complexity 1 drivers/video/fbdev/aty/radeonfb.h:radeonfb_bl_init Cyclomatic Complexity 1 drivers/video/fbdev/aty/radeonfb.h:radeonfb_bl_exit Cyclomatic Complexity 1 include/drm/drm_fb_helper.h:drm_fb_helper_remove_conflicting_framebuffers Cyclomatic Complexity 21 drivers/video/fbdev/aty/radeon_base.c:radeon_calc_pll_regs Cyclomatic Complexity 1 drivers/video/fbdev/aty/radeon_base.c:radeonfb_exit Cyclomatic Complexity 6 drivers/video/fbdev/aty/radeon_base.c:radeon_find_mem_vbios Cyclomatic Complexity 4 drivers/video/fbdev/aty/radeon_base.c:radeon_kick_out_firmware_fb Cyclomatic Complexity 5 drivers/video/fbdev/aty/radeon_base.c:radeonfb_pci_unregister Cyclomatic Complexity 1 drivers/video/fbdev/aty/radeon_base.c:radeon_show_one_edid Cyclomatic Complexity 3 drivers/video/fbdev/aty/radeon_base.c:radeon_show_edid2 Cyclomatic Complexity 3 drivers/video/fbdev/aty/radeon_base.c:radeon_show_edid1 Cyclomatic Complexity 2 drivers/video/fbdev/aty/radeon_base.c:radeon_set_fbinfo Cyclomatic Complexity 18 drivers/video/fbdev/aty/radeon_base.c:radeonfb_check_var Cyclomatic Complexity 2 drivers/video/fbdev/aty/radeon_base.c:radeon_unmap_ROM Cyclomatic Complexity 7 drivers/video/fbdev/aty/radeon_base.c:radeon_map_ROM Cyclomatic Complexity 16 drivers/video/fbdev/aty/radeon_base.c:radeonfb_setup Cyclomatic Complexity 2 drivers/video/fbdev/aty/radeon_base.c:radeonfb_init Cyclomatic Complexity 8 drivers/video/fbdev/aty/radeon_base.c:_radeon_msleep Cyclomatic Complexity 1 drivers/video/fbdev/aty/radeon_base.c:radeon_pll_errata_after_index_slow Cyclomatic Complexity 3 drivers/video/fbdev/aty/radeon_base.c:radeon_pll_errata_after_data_slow Cyclomatic Complexity 1 drivers/video/fbdev/aty/radeon_base.c:_OUTREGP
Cyclomatic Complexity 1 drivers/video/fbdev/aty/radeon_base.c:__INPLL
Cyclomatic Complexity 20 drivers/video/fbdev/aty/radeon_base.c:radeon_probe_pll_params Cyclomatic Complexity 10 drivers/video/fbdev/aty/radeon_base.c:radeon_get_pllinfo Cyclomatic Complexity 1 drivers/video/fbdev/aty/radeon_base.c:radeon_save_state Cyclomatic Complexity 1 drivers/video/fbdev/aty/radeon_base.c:__OUTPLL
Cyclomatic Complexity 1 drivers/video/fbdev/aty/radeon_base.c:__OUTPLLP Cyclomatic Complexity 3 drivers/video/fbdev/aty/radeon_base.c:_radeon_fifo_wait Cyclomatic Complexity 17 drivers/video/fbdev/aty/radeon_base.c:radeon_write_pll_regs Cyclomatic Complexity 25 drivers/video/fbdev/aty/radeon_base.c:radeon_identify_vram Cyclomatic Complexity 31 drivers/video/fbdev/aty/radeon_base.c:radeonfb_pci_register Cyclomatic Complexity 10 drivers/video/fbdev/aty/radeon_base.c:radeonfb_ioctl Cyclomatic Complexity 4 drivers/video/fbdev/aty/radeon_base.c:radeonfb_pan_display Cyclomatic Complexity 16 drivers/video/fbdev/aty/radeon_base.c:radeon_setcolreg Cyclomatic Complexity 9 drivers/video/fbdev/aty/radeon_base.c:radeonfb_setcmap Cyclomatic Complexity 6 drivers/video/fbdev/aty/radeon_base.c:radeonfb_setcolreg Cyclomatic Complexity 3 drivers/video/fbdev/aty/radeon_base.c:radeon_engine_flush Cyclomatic Complexity 3 drivers/video/fbdev/aty/radeon_base.c:_radeon_engine_idle Cyclomatic Complexity 2 drivers/video/fbdev/aty/radeon_base.c:radeon_lvds_timer_func Cyclomatic Complexity 17 drivers/video/fbdev/aty/radeon_base.c:radeon_screen_blank Cyclomatic Complexity 2 drivers/video/fbdev/aty/radeon_base.c:radeonfb_blank Cyclomatic Complexity 7 drivers/video/fbdev/aty/radeon_base.c:radeon_write_mode Cyclomatic Complexity 42 drivers/video/fbdev/aty/radeon_base.c:radeonfb_set_par In file included from drivers/video/fbdev/aty/radeon_base.c:91:0:
>> drivers/video/fbdev/aty/../edid.h:21:0: warning: "EDID_LENGTH" redefined
#define EDID_LENGTH 0x80 In file included from include/drm/drm_crtc.h:44:0,
from include/drm/drm_fb_helper.h:35,
from drivers/video/fbdev/aty/radeon_base.c:73:
include/drm/drm_edid.h:32:0: note: this is the location of the previous definition
#define EDID_LENGTH 128
vim +/EDID_LENGTH +21 drivers/video/fbdev/aty/../edid.h
^1da177e drivers/video/edid.h Linus Torvalds 2005-04-16 20
^1da177e drivers/video/edid.h Linus Torvalds 2005-04-16 @21 #define EDID_LENGTH 0x80 ^1da177e drivers/video/edid.h Linus Torvalds 2005-04-16 22 #define EDID_HEADER 0x00 ^1da177e drivers/video/edid.h Linus Torvalds 2005-04-16 23 #define EDID_HEADER_END 0x07
^1da177e drivers/video/edid.h Linus Torvalds 2005-04-16 24
:::::: The code at line 21 was first introduced by commit :::::: 1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 Linux-2.6.12-rc2
:::::: TO: Linus Torvalds <[email protected]> :::::: CC: Linus Torvalds <[email protected]>
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation