r8a77995 D3 DU and LVDS support
Subsystems (7)
cover r8a77995 D3 DU and LVDS support
From: Kieran Bingham <[email protected]>
Provide the PFC groups for the DU pin controls, and update the bindings for both the DU and LVDS to cover the r8a77995.
Add dt nodes for the DU, and LVDS, and enable VGA on the Draak board. Provide support for HDMI out through the ADV7511 component, on the LVDS channel.
Finally provide a 'proof-of-concept' patch for the ADV7612 device which shares the same bus and demonstrates setting the I2C slave maps such that they do not conflict with the ADV7511.
This series is dependant upon the LVDS rework from Laurent which is not yet finalised, however the DU only patches are not blocked by this.
Kieran Bingham (8):
pinctrl: sh-pfc: r8a77995: Add DU support
dt-bindings: display: renesas,du: Document r8a77995 bindings
dt-bindings: display: renesas,lvds: Add LVDS binding for D3
arm64: dts: renesas: r8a77995: add DU support
arm64: dts: renesas: r8a77995: Add LVDS support
arm64: dts: renesas: r8a77995-draak: Enable DU
arm64: dts: renesas: r8a77995-draak: Add HDMI Out through ADV7511 [PoC] arm64: dts: renesas: r8a77995-draak: Add ADV7612
.../bindings/display/bridge/renesas,lvds.txt | 1 + .../devicetree/bindings/display/renesas,du.txt | 2 + arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 150 +++++++++++++++++++++ arch/arm64/boot/dts/renesas/r8a77995.dtsi | 87 ++++++++++++ drivers/pinctrl/sh-pfc/pfc-r8a77995.c | 101 ++++++++++++++ 5 files changed, 341 insertions(+)
Signature · 1 line
2.7.4
PATCH 1/8 pinctrl: sh-pfc: r8a77995: Add DU support
From: Kieran Bingham <[email protected]>
Provide pin control support for the DU parallel RGB output signals.
--- drivers/pinctrl/sh-pfc/pfc-r8a77995.c | 101 ++++++++++++++++++++++++++++++++++ 1 file changed, 101 insertions(+)
drivers/pinctrl/sh-pfc/pfc-r8a77995.c +101 -0
@@ -1114,6 +1114,87 @@ static const unsigned int canfd1_data_mux[] = { CANFD1_TX_MARK, CANFD1_RX_MARK, }; +/* - DU --------------------------------------------------------------------- */ +static const unsigned int du_rgb666_pins[] = { +/* R[7:2], G[7:2], B[7:2] */ +RCAR_GP_PIN (1 ,23 ),RCAR_GP_PIN (1 ,22 ),RCAR_GP_PIN (1 ,21 ), +RCAR_GP_PIN (1 ,20 ),RCAR_GP_PIN (1 ,19 ),RCAR_GP_PIN (1 ,18 ), +RCAR_GP_PIN (1 ,15 ),RCAR_GP_PIN (1 ,14 ),RCAR_GP_PIN (1 ,13 ), +RCAR_GP_PIN (1 ,12 ),RCAR_GP_PIN (1 ,11 ),RCAR_GP_PIN (1 ,10 ), +RCAR_GP_PIN (1 ,7 ),RCAR_GP_PIN (1 ,6 ),RCAR_GP_PIN (1 ,5 ), +RCAR_GP_PIN (1 ,4 ),RCAR_GP_PIN (1 ,3 ),RCAR_GP_PIN (1 ,2 ), +}; +static const unsigned int du_rgb666_mux[] = { +DU_DR7_MARK ,DU_DR6_MARK ,DU_DR5_MARK ,DU_DR4_MARK , +DU_DR3_MARK ,DU_DR2_MARK , +DU_DG7_MARK ,DU_DG6_MARK ,DU_DG5_MARK ,DU_DG4_MARK , +DU_DG3_MARK ,DU_DG2_MARK , +DU_DB7_MARK ,DU_DB6_MARK ,DU_DB5_MARK ,DU_DB4_MARK , +DU_DB3_MARK ,DU_DB2_MARK , +}; +static const unsigned int du_rgb888_pins[] = { +/* R[7:0], G[7:0], B[7:0] */ +RCAR_GP_PIN (1 ,23 ),RCAR_GP_PIN (1 ,22 ),RCAR_GP_PIN (1 ,21 ), +RCAR_GP_PIN (1 ,20 ),RCAR_GP_PIN (1 ,19 ),RCAR_GP_PIN (1 ,18 ), +RCAR_GP_PIN (1 ,17 ),RCAR_GP_PIN (1 ,16 ), +RCAR_GP_PIN (1 ,15 ),RCAR_GP_PIN (1 ,14 ),RCAR_GP_PIN (1 ,13 ), +RCAR_GP_PIN (1 ,12 ),RCAR_GP_PIN (1 ,11 ),RCAR_GP_PIN (1 ,10 ), +RCAR_GP_PIN (1 ,9 ),RCAR_GP_PIN (1 ,8 ), +RCAR_GP_PIN (1 ,7 ),RCAR_GP_PIN (1 ,6 ),RCAR_GP_PIN (1 ,5 ), +RCAR_GP_PIN (1 ,4 ),RCAR_GP_PIN (1 ,3 ),RCAR_GP_PIN (1 ,2 ), +RCAR_GP_PIN (1 ,1 ),RCAR_GP_PIN (1 ,0 ), +}; +static const unsigned int du_rgb888_mux[] = { +DU_DR7_MARK ,DU_DR6_MARK ,DU_DR5_MARK ,DU_DR4_MARK , +DU_DR3_MARK ,DU_DR2_MARK ,DU_DR1_MARK ,DU_DR0_MARK , +DU_DG7_MARK ,DU_DG6_MARK ,DU_DG5_MARK ,DU_DG4_MARK , +DU_DG3_MARK ,DU_DG2_MARK ,DU_DG1_MARK ,DU_DG0_MARK , +DU_DB7_MARK ,DU_DB6_MARK ,DU_DB5_MARK ,DU_DB4_MARK , +DU_DB3_MARK ,DU_DB2_MARK ,DU_DB1_MARK ,DU_DB0_MARK , +}; +static const unsigned int du_dotclkout0_pins[] = { +/* CLKOUT */ +RCAR_GP_PIN (1 ,24 ), +}; +static const unsigned int du_dotclkout0_mux[] = { +DU_DOTCLKOUT0_MARK +}; +static const unsigned int du_sync_pins[] = { +/* HSYNC, VSYNC */ +RCAR_GP_PIN (1 ,25 ),RCAR_GP_PIN (1 ,26 ), +}; +static const unsigned int du_sync_mux[] = { +DU_HSYNC_MARK ,DU_VSYNC_MARK +}; +static const unsigned int du_disp_pins[] = { +/* DISP */ +RCAR_GP_PIN (2 ,1 ), +}; +static const unsigned int du_disp_mux[] = { +DU_DISP_MARK , +}; +static const unsigned int du_dotclkin1_pins[] = { +/* DOTCLKOUT0 */ +RCAR_GP_PIN (1 ,28 ), +}; +static const unsigned int du_dotclkin1_mux[] = { +DU_DOTCLKIN1_MARK , +}; +static const unsigned int du_disp_cde_pins[] = { +/* DISP/CDE */ +RCAR_GP_PIN (1 ,28 ), +}; +static const unsigned int du_disp_cde_mux[] = { +DU_DISP_CDE_MARK , +}; +static const unsigned int du_cde_pins[] = { +/* CDE */ +RCAR_GP_PIN (1 ,29 ), +}; +static const unsigned int du_cde_mux[] = { +DU_CDE_MARK , +}; +/* - I2C -------------------------------------------------------------------- */ static const unsigned int i2c0_pins[] = {/* SCL, SDA */
@@ -1568,6 +1649,14 @@ static const struct sh_pfc_pin_group pinmux_groups[] = {SH_PFC_PIN_GROUP (can_clk),SH_PFC_PIN_GROUP (canfd0_data),SH_PFC_PIN_GROUP (canfd1_data), +SH_PFC_PIN_GROUP (du_rgb666), +SH_PFC_PIN_GROUP (du_rgb888), +SH_PFC_PIN_GROUP (du_dotclkout0), +SH_PFC_PIN_GROUP (du_sync), +SH_PFC_PIN_GROUP (du_disp), +SH_PFC_PIN_GROUP (du_dotclkin1), +SH_PFC_PIN_GROUP (du_disp_cde), +SH_PFC_PIN_GROUP (du_cde),SH_PFC_PIN_GROUP (i2c0),SH_PFC_PIN_GROUP (i2c1), SH_PFC_PIN_GROUP(i2c2_a),
@@ -1664,6 +1753,17 @@ static const char * const canfd1_groups[] = { "canfd1_data", }; +static const char *const du_groups[] = { +"du_rgb666" , +"du_rgb888" , +"du_dotclk_out_0" , +"du_sync" , +"du_disp" , +"du_dotclk_in_1" , +"du_disp_cde" , +"du_cde" , +}; +static const char *const i2c0_groups[] = {"i2c0" , };
@@ -1779,6 +1879,7 @@ static const struct sh_pfc_function pinmux_functions[] = {SH_PFC_FUNCTION (can_clk),SH_PFC_FUNCTION (canfd0),SH_PFC_FUNCTION (canfd1), +SH_PFC_FUNCTION (du),SH_PFC_FUNCTION (i2c0),SH_PFC_FUNCTION (i2c1), SH_PFC_FUNCTION(i2c2),
Signature · 1 line
2.7.4
Re: [PATCH 1/8] pinctrl: sh-pfc: r8a77995: Add DU support
This patch duplicates work performed by Ulrich.
Please consider this patch dropped, and no need for review.
(especially the obvious error in the pin-values)
Oh well - it was a fun exercise to go through :-)
--
Regards
Kieran
Quoted 143 lines · Kieran Bingham
From: Kieran Bingham <[email protected]>
Provide pin control support for the DU parallel RGB output signals.
Signed-off-by Kieran Bingham <[email protected]>--- drivers/pinctrl/sh-pfc/pfc-r8a77995.c | 101 ++++++++++++++++++++++++++++++++++ 1 file changed, 101 insertions(+)drivers/pinctrl/sh-pfc/pfc-r8a77995.c +101
-0@@ -1114,6 +1114,87 @@ static const unsigned int canfd1_data_mux[] = { CANFD1_TX_MARK, CANFD1_RX_MARK, }; +/* - DU --------------------------------------------------------------------- */ +static const unsigned int du_rgb666_pins[] = { +/* R[7:2], G[7:2], B[7:2] */ +RCAR_GP_PIN (1 ,23 ),RCAR_GP_PIN (1 ,22 ),RCAR_GP_PIN (1 ,21 ), +RCAR_GP_PIN (1 ,20 ),RCAR_GP_PIN (1 ,19 ),RCAR_GP_PIN (1 ,18 ), +RCAR_GP_PIN (1 ,15 ),RCAR_GP_PIN (1 ,14 ),RCAR_GP_PIN (1 ,13 ), +RCAR_GP_PIN (1 ,12 ),RCAR_GP_PIN (1 ,11 ),RCAR_GP_PIN (1 ,10 ), +RCAR_GP_PIN (1 ,7 ),RCAR_GP_PIN (1 ,6 ),RCAR_GP_PIN (1 ,5 ), +RCAR_GP_PIN (1 ,4 ),RCAR_GP_PIN (1 ,3 ),RCAR_GP_PIN (1 ,2 ), +}; +static const unsigned int du_rgb666_mux[] = { +DU_DR7_MARK ,DU_DR6_MARK ,DU_DR5_MARK ,DU_DR4_MARK , +DU_DR3_MARK ,DU_DR2_MARK , +DU_DG7_MARK ,DU_DG6_MARK ,DU_DG5_MARK ,DU_DG4_MARK , +DU_DG3_MARK ,DU_DG2_MARK , +DU_DB7_MARK ,DU_DB6_MARK ,DU_DB5_MARK ,DU_DB4_MARK , +DU_DB3_MARK ,DU_DB2_MARK , +}; +static const unsigned int du_rgb888_pins[] = { +/* R[7:0], G[7:0], B[7:0] */ +RCAR_GP_PIN (1 ,23 ),RCAR_GP_PIN (1 ,22 ),RCAR_GP_PIN (1 ,21 ), +RCAR_GP_PIN (1 ,20 ),RCAR_GP_PIN (1 ,19 ),RCAR_GP_PIN (1 ,18 ), +RCAR_GP_PIN (1 ,17 ),RCAR_GP_PIN (1 ,16 ), +RCAR_GP_PIN (1 ,15 ),RCAR_GP_PIN (1 ,14 ),RCAR_GP_PIN (1 ,13 ), +RCAR_GP_PIN (1 ,12 ),RCAR_GP_PIN (1 ,11 ),RCAR_GP_PIN (1 ,10 ), +RCAR_GP_PIN (1 ,9 ),RCAR_GP_PIN (1 ,8 ), +RCAR_GP_PIN (1 ,7 ),RCAR_GP_PIN (1 ,6 ),RCAR_GP_PIN (1 ,5 ), +RCAR_GP_PIN (1 ,4 ),RCAR_GP_PIN (1 ,3 ),RCAR_GP_PIN (1 ,2 ), +RCAR_GP_PIN (1 ,1 ),RCAR_GP_PIN (1 ,0 ), +}; +static const unsigned int du_rgb888_mux[] = { +DU_DR7_MARK ,DU_DR6_MARK ,DU_DR5_MARK ,DU_DR4_MARK , +DU_DR3_MARK ,DU_DR2_MARK ,DU_DR1_MARK ,DU_DR0_MARK , +DU_DG7_MARK ,DU_DG6_MARK ,DU_DG5_MARK ,DU_DG4_MARK , +DU_DG3_MARK ,DU_DG2_MARK ,DU_DG1_MARK ,DU_DG0_MARK , +DU_DB7_MARK ,DU_DB6_MARK ,DU_DB5_MARK ,DU_DB4_MARK , +DU_DB3_MARK ,DU_DB2_MARK ,DU_DB1_MARK ,DU_DB0_MARK , +}; +static const unsigned int du_dotclkout0_pins[] = { +/* CLKOUT */ +RCAR_GP_PIN (1 ,24 ), +}; +static const unsigned int du_dotclkout0_mux[] = { +DU_DOTCLKOUT0_MARK +}; +static const unsigned int du_sync_pins[] = { +/* HSYNC, VSYNC */ +RCAR_GP_PIN (1 ,25 ),RCAR_GP_PIN (1 ,26 ), +}; +static const unsigned int du_sync_mux[] = { +DU_HSYNC_MARK ,DU_VSYNC_MARK +}; +static const unsigned int du_disp_pins[] = { +/* DISP */ +RCAR_GP_PIN (2 ,1 ), +}; +static const unsigned int du_disp_mux[] = { +DU_DISP_MARK , +}; +static const unsigned int du_dotclkin1_pins[] = { +/* DOTCLKOUT0 */ +RCAR_GP_PIN (1 ,28 ), +}; +static const unsigned int du_dotclkin1_mux[] = { +DU_DOTCLKIN1_MARK , +}; +static const unsigned int du_disp_cde_pins[] = { +/* DISP/CDE */ +RCAR_GP_PIN (1 ,28 ), +}; +static const unsigned int du_disp_cde_mux[] = { +DU_DISP_CDE_MARK , +}; +static const unsigned int du_cde_pins[] = { +/* CDE */ +RCAR_GP_PIN (1 ,29 ), +}; +static const unsigned int du_cde_mux[] = { +DU_CDE_MARK , +}; +/* - I2C -------------------------------------------------------------------- */ static const unsigned int i2c0_pins[] = {/* SCL, SDA */ @@ -1568,6 +1649,14 @@ static const struct sh_pfc_pin_group pinmux_groups[] = {SH_PFC_PIN_GROUP (can_clk),SH_PFC_PIN_GROUP (canfd0_data),SH_PFC_PIN_GROUP (canfd1_data), +SH_PFC_PIN_GROUP (du_rgb666), +SH_PFC_PIN_GROUP (du_rgb888), +SH_PFC_PIN_GROUP (du_dotclkout0), +SH_PFC_PIN_GROUP (du_sync), +SH_PFC_PIN_GROUP (du_disp), +SH_PFC_PIN_GROUP (du_dotclkin1), +SH_PFC_PIN_GROUP (du_disp_cde), +SH_PFC_PIN_GROUP (du_cde),SH_PFC_PIN_GROUP (i2c0),SH_PFC_PIN_GROUP (i2c1), SH_PFC_PIN_GROUP(i2c2_a),@@ -1664,6 +1753,17 @@ static const char * const canfd1_groups[] = { "canfd1_data", }; +static const char *const du_groups[] = { +"du_rgb666" , +"du_rgb888" , +"du_dotclk_out_0" , +"du_sync" , +"du_disp" , +"du_dotclk_in_1" , +"du_disp_cde" , +"du_cde" , +}; +static const char *const i2c0_groups[] = {"i2c0" , };@@ -1779,6 +1879,7 @@ static const struct sh_pfc_function pinmux_functions[] = {SH_PFC_FUNCTION (can_clk),SH_PFC_FUNCTION (canfd0),SH_PFC_FUNCTION (canfd1), +SH_PFC_FUNCTION (du),SH_PFC_FUNCTION (i2c0),SH_PFC_FUNCTION (i2c1), SH_PFC_FUNCTION(i2c2),
PATCH 2/8 dt-bindings: display: renesas,du: Document r8a77995 bindings
In reply to Kieran BinghamFrom: Kieran Bingham <[email protected]>
Document the D3 (r8a77995) SoC in the R-Car DU bindings.
--- Documentation/devicetree/bindings/display/renesas,du.txt | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/display/renesas,du.txt +2 -0
@@ -13,6 +13,7 @@ Required Properties: - "renesas,du-r8a7794" for R8A7794 (R-Car E2) compatible DU - "renesas,du-r8a7795" for R8A7795 (R-Car H3) compatible DU - "renesas,du-r8a7796" for R8A7796 (R-Car M3-W) compatible DU + - "renesas,du-r8a77995" for R8A77995 (R-Car D3) compatible DU - reg: A list of base address and length of each memory resource, one for each entry in the reg-names property.
@@ -60,6 +61,7 @@ corresponding to each DU output. R8A7794 (R-Car E2) DPAD 0 DPAD 1 - - R8A7795 (R-Car H3) DPAD 0 HDMI 0 HDMI 1 LVDS 0 R8A7796 (R-Car M3-W) DPAD 0 HDMI 0 LVDS 0 - + R8A77995 (R-Car D3) DPAD 0 LVDS 0 LVDS 1 - Example: R8A7795 (R-Car H3) ES2.0 DU
Signature · 1 line
2.7.4
Re: [PATCH 2/8] dt-bindings: display: renesas,du: Document r8a77995 bindings
Hi Kieran,
Thank you for the patch.
Quoted 5 lines · On Thursday, 15 February 2018 10:38:17 EET Kieran Bingham wrote:
From: Kieran Bingham <[email protected]>
Document the D3 (r8a77995) SoC in the R-Car DU bindings.
Signed-off-by Kieran Bingham <[email protected]>
and applied to my tree.
Quoted 25 lines
--- Documentation/devicetree/bindings/display/renesas,du.txt | 2 ++ 1 file changed, 2 insertions(+)(quoted diff) +0
-0
b/Documentation/devicetree/bindings/display/renesas,du.txtindex8f6e0e118e3e..56f67453b9aa100644Documentation/devicetree/bindings/display/renesas,du.txt +1
-0@@ -13,6 +13,7 @@ Required Properties: - "renesas,du-r8a7794" for R8A7794 (R-Car E2) compatible DU - "renesas,du-r8a7795" for R8A7795 (R-Car H3) compatible DU - "renesas,du-r8a7796" for R8A7796 (R-Car M3-W) compatible DU + - "renesas,du-r8a77995" for R8A77995 (R-Car D3) compatible DU - reg: A list of base address and length of each memory resource, one foreach entry in the reg-names property.
Documentation/devicetree/bindings/display/renesas,du.txt +1
-0@@ -60,6 +61,7 @@ corresponding to each DU output. R8A7794 (R-Car E2) DPAD 0 DPAD 1 - - R8A7795 (R-Car H3) DPAD 0 HDMI 0 HDMI 1 LVDS 0 R8A7796 (R-Car M3-W) DPAD 0 HDMI 0 LVDS 0 - + R8A77995 (R-Car D3) DPAD 0 LVDS 0 LVDS 1 - Example: R8A7795 (R-Car H3) ES2.0 DU
Signature · 8 lines
Regards, Laurent Pinchart _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH 3/8 dt-bindings: display: renesas,lvds: Add LVDS binding for D3
In reply to Kieran BinghamFrom: Kieran Bingham <[email protected]>
The D3 supports two LVDS channels. Extend the binding to support them.
--- Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt +1 -0
@@ -14,6 +14,7 @@ Required properties: - compatible : Shall contain one of - "renesas,lvds-r8a7795" for R8A7795 (R-Car H3) compatible LVDS encoders - "renesas,lvds-r8a7796" for R8A7796 (R-Car M3-W) compatible LVDS encoders + - "renesas,lvds-r8a77995" for R8A77995 (R-Car D3) compatible LVDS encoders - reg: Base address and length for the memory-mapped registers - clocks: A phandle + clock-specifier pair for the functional clock
Signature · 1 line
2.7.4
Re: [PATCH 3/8] dt-bindings: display: renesas,lvds: Add LVDS binding for D3
Quoted 14 lines · Kieran Bingham
From: Kieran Bingham <[email protected]>
The D3 supports two LVDS channels. Extend the binding to support them.
Signed-off-by Kieran Bingham <[email protected]>--- Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt | 1 + 1 file changed, 1 insertion(+)Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt +0
-0
Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt Required properties: · line 17
Quoted 4 lines
Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt +1
-0@@ -14,6 +14,7 @@ Required properties: - compatible : Shall contain one of - "renesas,lvds-r8a7795" for R8A7795 (R-Car H3) compatible LVDS encoders - "renesas,lvds-r8a7796" for R8A7796 (R-Car M3-W) compatible LVDS encoders + - "renesas,lvds-r8a77995" for R8A77995 (R-Car D3) compatible LVDS encoders
Hi Laurent,
Are we unable to have a generic lvds-gen3 here?
(Although to perhaps answer my own question I see that the D3/E3 have extra registers)
Also "lets pretend" that I intentionally separated out the LVDS updates to the rcar_lvds_of_table :)
--
Kieran
Quoted 4 lines
Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt +0
-0- reg: Base address and length for the memory-mapped registers - clocks: A phandle + clock-specifier pair for the functional clock
Laurent Pinchart
reviewerRe: [PATCH 3/8] dt-bindings: display: renesas,lvds: Add LVDS binding for D3
Hi Kieran,
Quoted 29 lines · On Thursday, 15 February 2018 10:45:33 EET Kieran Bingham wrote:
Quoted 24 lines · Kieran Bingham
From: Kieran Bingham <[email protected]>
The D3 supports two LVDS channels. Extend the binding to support them.
Signed-off-by Kieran Bingham <[email protected]>---
Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt | 1 + 1 file changed, 1 insertion(+)diff --git
a/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txtb/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txtindex79860f58a7ad..0dcf488b70df100644Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt +1
-0@@ -14,6 +14,7 @@ Required properties: - compatible : Shall contain one of - "renesas,lvds-r8a7795" for R8A7795 (R-Car H3) compatible LVDS encoders - "renesas,lvds-r8a7796" for R8A7796 (R-Car M3-W) compatible LVDS encoders + - "renesas,lvds-r8a77995" for R8A77995 (R-Car D3) compatible LVDSQuoted 1 line
encoders
Hi Laurent,
Quoted 7 lines
Are we unable to have a generic lvds-gen3 here?
(Although to perhaps answer my own question I see that the D3/E3 have extra registers)
Also "lets pretend" that I intentionally separated out the LVDS updates to the
rcar_lvds_of_table:)
We could for H3 and M3-W, but as you've noticed D3/E3 differ, and so does V3M.
Quoted 2 lines
Quoted 2 lines
- reg: Base address and length for the memory-mapped registers
- clocks: A phandle + clock-specifier pair for the functional clock
Signature · 8 lines
Regards, Laurent Pinchart _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH 3/8] dt-bindings: display: renesas,lvds: Add LVDS binding for D3
In reply to Kieran BinghamHi Kieran,
Thank you for the patch.
Quoted 19 lines · On Thursday, 15 February 2018 10:38:18 EET Kieran Bingham wrote:
From: Kieran Bingham <[email protected]>
The D3 supports two LVDS channels. Extend the binding to support them.
Signed-off-by Kieran Bingham <[email protected]>--- Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt | 1 + 1 file changed, 1 insertion(+)diff --git
a/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txtb/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txtindex79860f58a7ad..0dcf488b70df100644Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt +0
-0@@ -14,6 +14,7 @@ Required properties: - compatible : Shall contain one of - "renesas,lvds-r8a7795" for R8A7795 (R-Car H3) compatible LVDS encoders - "renesas,lvds-r8a7796" for R8A7796 (R-Car M3-W) compatible LVDS
Quoted 3 lines
encoders
+ - "renesas,lvds-r8a77995" for R8A77995 (R-Car D3) compatible LVDS encoders
This should be "renesas,r8a77995-lvds". I've already fixed the series you've based this patch on.
Apart from this,
and taken in my tree with the compatible string fixed.
Quoted 3 lines
- reg: Base address and length for the memory-mapped registers
- clocks: A phandle + clock-specifier pair for the functional clock
Signature · 3 lines
Regards, Laurent Pinchart
PATCH 4/8 arm64: dts: renesas: r8a77995: add DU support
In reply to Kieran BinghamFrom: Kieran Bingham <[email protected]>
Define the generic r8a77995 part of the DU device node.
--- arch/arm64/boot/dts/renesas/r8a77995.dtsi | 35 +++++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995.dtsi +35 -0
@@ -748,6 +748,41 @@ resets = <&cpg 602>; iommus = <&ipmmu_vi0 9>; }; + + du: display at feb00000 { + compatible = "renesas,du-r8a77995"; + reg = <0 0xfeb00000 0 0x80000>; + interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 724>, + <&cpg CPG_MOD 723>; + clock-names = "du.0", "du.1"; + vsps = <&vspd0 0 &vspd1 0>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + du_out_rgb: endpoint { + }; + }; + + port at 1 { + reg = <1>; + du_out_lvds0: endpoint { + }; + }; + + port at 2 { + reg = <2>; + du_out_lvds1: endpoint { + }; + }; + }; + }; }; timer {
Signature · 1 line
2.7.4
Re: [PATCH 4/8] arm64: dts: renesas: r8a77995: add DU support
Hi Kieran,
Thank you for the patch.
Quoted 5 lines · On Thursday, 15 February 2018 10:38:19 EET Kieran Bingham wrote:
From: Kieran Bingham <[email protected]>
Define the generic r8a77995 part of the DU device node.
Signed-off-by Kieran Bingham <[email protected]>
I assume Simon will take care of this patch.
Quoted 51 lines
--- arch/arm64/boot/dts/renesas/r8a77995.dtsi | 35 ++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)(quoted diff) +0
-0
b/arch/arm64/boot/dts/renesas/r8a77995.dtsiindex0db242114bc5..a57d5fecf79c100644arch/arm64/boot/dts/renesas/r8a77995.dtsi +35
-0@@ -748,6 +748,41 @@ resets = <&cpg 602>; iommus = <&ipmmu_vi0 9>; }; + + du: display@feb00000 { + compatible = "renesas,du-r8a77995"; + reg = <0 0xfeb00000 0 0x80000>; + interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 724>, + <&cpg CPG_MOD 723>; + clock-names = "du.0", "du.1"; + vsps = <&vspd0 0 &vspd1 0>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + du_out_rgb: endpoint { + }; + }; + + port@1 { + reg = <1>; + du_out_lvds0: endpoint { + }; + }; + + port@2 { + reg = <2>; + du_out_lvds1: endpoint { + }; + }; + }; + }; }; timer {
Signature · 3 lines
Regards, Laurent Pinchart
Simon Horman
AppliedRe: [PATCH 4/8] arm64: dts: renesas: r8a77995: add DU support
Quoted 7 lines · Laurent Pinchart
Hi Kieran,
Thank you for the patch.
Quoted 2 lines · On Thursday, 15 February 2018 10:38:19 EET Kieran Bingham wrote:
From: Kieran Bingham <[email protected]>
Quoted 7 lines
Quoted 3 lines
Define the generic r8a77995 part of the DU device node.
Signed-off-by Kieran Bingham <[email protected]>Reviewed-by Laurent Pinchart <[email protected]>I assume Simon will take care of this patch.
Thanks, applied.
PATCH 5/8 arm64: dts: renesas: r8a77995: Add LVDS support
In reply to Kieran BinghamFrom: Kieran Bingham <[email protected]>
The r8a77995 D3 platform has 2 LVDS channels connected to the DU.
--- arch/arm64/boot/dts/renesas/r8a77995.dtsi | 52 +++++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995.dtsi +52 -0
@@ -773,18 +773,70 @@ port at 1 { reg = <1>; du_out_lvds0: endpoint { + remote-endpoint = <&du_out_lvds0>; }; }; port at 2 { reg = <2>; du_out_lvds1: endpoint { + remote-endpoint = <&du_out_lvds1>; }; }; }; }; }; + lvds0: lvds at feb90000 { + compatible = "renesas,lvds-r8a77995"; + reg = <0 0xfeb90000 0 0x20>; + clocks = <&cpg CPG_MOD 727>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + lvds0_in: endpoint { + remote-endpoint = <&du_out_lvds0>; + }; + }; + + port at 1 { + reg = <1>; + lvds0_out: endpoint { + }; + }; + }; + }; + + lvds1: lvds at feb90100 { + compatible = "renesas,lvds-r8a77995"; + reg = <0 0xfeb90100 0 0x20>; + clocks = <&cpg CPG_MOD 727>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + lvds1_in: endpoint { + remote-endpoint = <&du_out_lvds1>; + }; + }; + + port at 1 { + reg = <1>; + lvds1_out: endpoint { + }; + }; + }; + }; + timer { compatible = "arm,armv8-timer"; interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
Signature · 1 line
2.7.4
Re: [PATCH 5/8] arm64: dts: renesas: r8a77995: Add LVDS support
Hi Kieran,
Quoted 5 lines · Kieran Bingham
From: Kieran Bingham <[email protected]>
The r8a77995 D3 platform has 2 LVDS channels connected to the DU.
Signed-off-by Kieran Bingham <[email protected]>
I love your patch!
Yet something to improve...
Quoted 15 lines
arch/arm64/boot/dts/renesas/r8a77995.dtsi +2
-0@@ -773,18 +773,70 @@ port at 1 { reg = <1>; du_out_lvds0: endpoint { + remote-endpoint = <&du_out_lvds0>; }; }; port at 2 { reg = <2>; du_out_lvds1: endpoint { + remote-endpoint = <&du_out_lvds1>; };
arch/arm64/boot/dts/renesas/r8a77995.dtsi line 794
Quoted 10 lines
arch/arm64/boot/dts/renesas/r8a77995.dtsi +5
-0}; }; }; }; + lvds0: lvds at feb90000 { + compatible = "renesas,lvds-r8a77995"; + reg = <0 0xfeb90000 0 0x20>; + clocks = <&cpg CPG_MOD 727>; + status = "disabled";
Missing resets, power-domains
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Re: [PATCH 5/8] arm64: dts: renesas: r8a77995: Add LVDS support
Hi Geert,
Quoted 32 lines · Geert Uytterhoeven
Hi Kieran,
Quoted 5 lines · Kieran Bingham
From: Kieran Bingham <[email protected]>
The r8a77995 D3 platform has 2 LVDS channels connected to the DU.
Signed-off-by Kieran Bingham <[email protected]>I love your patch!
Yet something to improve...Quoted 20 lines
arch/arm64/boot/dts/renesas/r8a77995.dtsi +2
-0@@ -773,18 +773,70 @@ port at 1 { reg = <1>; du_out_lvds0: endpoint { + remote-endpoint = <&du_out_lvds0>; }; }; port at 2 { reg = <2>; du_out_lvds1: endpoint { + remote-endpoint = <&du_out_lvds1>; }; }; }; }; };
Quoted 7 lines
arch/arm64/boot/dts/renesas/r8a77995.dtsi line 794
Quoted 5 lines
arch/arm64/boot/dts/renesas/r8a77995.dtsi +5
-0+ lvds0: lvds at feb90000 { + compatible = "renesas,lvds-r8a77995"; + reg = <0 0xfeb90000 0 0x20>; + clocks = <&cpg CPG_MOD 727>; + status = "disabled";Missing resets, power-domains
Both lvds0, and lvds1 are actually the same 'module' (just different mappings within the same IP block).
That means they will share clock, reset etc.
Will specifying the resets cause one to affect the other unduly?
like if one becomes un-used, will it power down? or is it refcounted, and will gracefully handle both device nodes from the same device?
I'm already fairly sure clocks is fine for this - but it's just the reset's that worry me. If the reset module tries to reset lvds0 for some reason - would lvds1 get reset as a side effect ...
Or perhaps that won't ever happen with an :
power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; resets = <&cpg 727>;
Regards
--
Kieran
Quoted 12 lines
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.orgIn personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Re: [PATCH 5/8] arm64: dts: renesas: r8a77995: Add LVDS support
Hi Kieran,
Quoted 44 lines · Kieran Bingham
Quoted 30 lines · Geert Uytterhoeven
Quoted 5 lines · Kieran Bingham
From: Kieran Bingham <[email protected]>
The r8a77995 D3 platform has 2 LVDS channels connected to the DU.
Signed-off-by Kieran Bingham <[email protected]>I love your patch!
Yet something to improve...Quoted 20 lines
arch/arm64/boot/dts/renesas/r8a77995.dtsi +2
-0@@ -773,18 +773,70 @@ port at 1 { reg = <1>; du_out_lvds0: endpoint { + remote-endpoint = <&du_out_lvds0>; }; }; port at 2 { reg = <2>; du_out_lvds1: endpoint { + remote-endpoint = <&du_out_lvds1>; }; }; }; }; };Quoted 7 lines
arch/arm64/boot/dts/renesas/r8a77995.dtsi line 794
Quoted 5 lines
arch/arm64/boot/dts/renesas/r8a77995.dtsi +5
-0+ lvds0: lvds at feb90000 { + compatible = "renesas,lvds-r8a77995"; + reg = <0 0xfeb90000 0 0x20>; + clocks = <&cpg CPG_MOD 727>; + status = "disabled";Missing resets, power-domains
Both lvds0, and lvds1 are actually the same 'module' (just different mappings within the same IP block).
That means they will share clock, reset etc.
Quoted 8 lines
Will specifying the resets cause one to affect the other unduly?
like if one becomes un-used, will it power down? or is it refcounted, and will gracefully handle both device nodes from the same device?
I'm already fairly sure clocks is fine for this - but it's just the reset's that worry me. If the reset module tries to reset lvds0 for some reason - would lvds1 get reset as a side effect ...
Clocks handle sharing fine, they do refcounting.
For resets, there is some sharing/exclusive support, but we don't have that much experience with resets as we don't use it that much yet (USB uses it). So for now it's mostly about "describing the hardware".
Triggering a reset will indeed reset all modules using the same reset. The same is true for e.g. PWM.
Quoted 4 lines
Or perhaps that won't ever happen with an :
power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; resets = <&cpg 727>;
The power-domains property is related to power management (in this case clock domain only, as it's the "always-on" domain), not reset.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Laurent Pinchart
reviewerRe: [PATCH 5/8] arm64: dts: renesas: r8a77995: Add LVDS support
In reply to Kieran BinghamHi Kieran,
Thank you for the patch.
Quoted 16 lines · On Thursday, 15 February 2018 10:38:20 EET Kieran Bingham wrote:
From: Kieran Bingham <[email protected]>
The r8a77995 D3 platform has 2 LVDS channels connected to the DU.
Signed-off-by Kieran Bingham <[email protected]>--- arch/arm64/boot/dts/renesas/r8a77995.dtsi | 52 ++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+)(quoted diff) +0
-0
b/arch/arm64/boot/dts/renesas/r8a77995.dtsiindexa57d5fecf79c..7851e37cfff1100644arch/arm64/boot/dts/renesas/r8a77995.dtsi +0
-0@@ -773,18 +773,70 @@ port@1 {
arch/arm64/boot/dts/renesas/r8a77995.dtsi line 783
Quoted 10 lines
arch/arm64/boot/dts/renesas/r8a77995.dtsi +2
-0reg = <1>; du_out_lvds0: endpoint { + remote-endpoint = <&du_out_lvds0>; }; }; port@2 { reg = <2>; du_out_lvds1: endpoint { + remote-endpoint = <&du_out_lvds1>;
It's interesting how the DU ports reference themselves :-)
Quoted 60 lines
arch/arm64/boot/dts/renesas/r8a77995.dtsi +50
-0}; }; }; }; }; + lvds0: lvds@feb90000 { + compatible = "renesas,lvds-r8a77995"; + reg = <0 0xfeb90000 0 0x20>; + clocks = <&cpg CPG_MOD 727>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + lvds0_in: endpoint { + remote-endpoint = <&du_out_lvds0>; + }; + }; + + port@1 { + reg = <1>; + lvds0_out: endpoint { + }; + }; + }; + }; + + lvds1: lvds@feb90100 { + compatible = "renesas,lvds-r8a77995"; + reg = <0 0xfeb90100 0 0x20>; + clocks = <&cpg CPG_MOD 727>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + lvds1_in: endpoint { + remote-endpoint = <&du_out_lvds1>; + }; + }; + + port@1 { + reg = <1>; + lvds1_out: endpoint { + }; + }; + }; + }; + timer { compatible = "arm,armv8-timer"; interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) |
IRQ_TYPE_LEVEL_LOW)>,
Signature · 3 lines
Regards, Laurent Pinchart
Re: [PATCH 5/8] arm64: dts: renesas: r8a77995: Add LVDS support
Quoted 27 lines · Laurent Pinchart
Hi Kieran,
Thank you for the patch.
Quoted 22 lines · On Thursday, 15 February 2018 10:38:20 EET Kieran Bingham wrote:
From: Kieran Bingham <[email protected]>
The r8a77995 D3 platform has 2 LVDS channels connected to the DU.
Signed-off-by Kieran Bingham <[email protected]>--- arch/arm64/boot/dts/renesas/r8a77995.dtsi | 52 ++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+)(quoted diff) +0
-0
b/arch/arm64/boot/dts/renesas/r8a77995.dtsiindexa57d5fecf79c..7851e37cfff1100644arch/arm64/boot/dts/renesas/r8a77995.dtsi +1
-0@@ -773,18 +773,70 @@ port at 1 { reg = <1>; du_out_lvds0: endpoint { + remote-endpoint = <&du_out_lvds0>; }; };
Quoted 6 lines
arch/arm64/boot/dts/renesas/r8a77995.dtsi line 783
Quoted 4 lines
arch/arm64/boot/dts/renesas/r8a77995.dtsi +1
-0port at 2 { reg = <2>; du_out_lvds1: endpoint { + remote-endpoint = <&du_out_lvds1>;It's interesting how the DU ports reference themselves :-)
Ah, yes - that's ... that's a feature...
--
Kieran
Quoted 61 lines
Quoted 60 lines
arch/arm64/boot/dts/renesas/r8a77995.dtsi +50
-0}; }; }; }; }; + lvds0: lvds at feb90000 { + compatible = "renesas,lvds-r8a77995"; + reg = <0 0xfeb90000 0 0x20>; + clocks = <&cpg CPG_MOD 727>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + lvds0_in: endpoint { + remote-endpoint = <&du_out_lvds0>; + }; + }; + + port at 1 { + reg = <1>; + lvds0_out: endpoint { + }; + }; + }; + }; + + lvds1: lvds at feb90100 { + compatible = "renesas,lvds-r8a77995"; + reg = <0 0xfeb90100 0 0x20>; + clocks = <&cpg CPG_MOD 727>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + lvds1_in: endpoint { + remote-endpoint = <&du_out_lvds1>; + }; + }; + + port at 1 { + reg = <1>; + lvds1_out: endpoint { + }; + }; + }; + }; + timer { compatible = "arm,armv8-timer"; interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) |
IRQ_TYPE_LEVEL_LOW)>,
Re: [PATCH 5/8] arm64: dts: renesas: r8a77995: Add LVDS support
In reply to Kieran BinghamQuoted 5 lines · Kieran Bingham
From: Kieran Bingham <[email protected]>
The r8a77995 D3 platform has 2 LVDS channels connected to the DU.
Signed-off-by Kieran Bingham <[email protected]>
It looks like there has been some review of this patch that needs addressing, I've marked it as "Changes Requested".
PATCH 6/8 arm64: dts: renesas: r8a77995-draak: Enable DU
In reply to Kieran BinghamFrom: Kieran Bingham <[email protected]>
Enable the DU, providing only the VGA output for now.
--- arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 51 ++++++++++++++++++++++++++ 1 file changed, 51 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +51 -0
@@ -27,6 +27,38 @@ stdout-path = "serial0:115200n8"; }; + vga { + compatible = "vga-connector"; + + port { + vga_in: endpoint { + remote-endpoint = <&adv7123_out>; + }; + }; + }; + + vga-encoder { + compatible = "adi,adv7123"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + adv7123_in: endpoint { + remote-endpoint = <&du_out_rgb>; + }; + }; + port at 1 { + reg = <1>; + adv7123_out: endpoint { + remote-endpoint = <&vga_in>; + }; + }; + }; + }; + memory at 48000000 { device_type = "memory"; /* first 128MB is reserved for secure area. */
@@ -46,6 +78,11 @@ }; }; + du_pins: du { + groups = "du_rgb888", "du_sync", "du_disp", "du_dotclkout0"; + function = "du"; + }; + i2c0_pins: i2c0 { groups = "i2c0"; function = "i2c0";
@@ -95,6 +132,20 @@ status = "okay"; }; +&du { + pinctrl-0 = <&du_pins>; + pinctrl-names = "default"; + status = "okay"; + + ports { + port at 0 { + endpoint { + remote-endpoint = <&adv7123_in>; + }; + }; + }; +}; + &ehci0 { status = "okay"; };
Signature · 1 line
2.7.4
Re: [PATCH 6/8] arm64: dts: renesas: r8a77995-draak: Enable DU
Hi Kieran,
Thank you for the patch.
Quoted 5 lines · On Thursday, 15 February 2018 10:38:21 EET Kieran Bingham wrote:
From: Kieran Bingham <[email protected]>
Enable the DU, providing only the VGA output for now.
Signed-off-by Kieran Bingham <[email protected]>
I assume Simon will take care of this patch.
Quoted 81 lines
--- arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 51 +++++++++++++++++++++++ 1 file changed, 51 insertions(+)(quoted diff) +0
-0
b/arch/arm64/boot/dts/renesas/r8a77995-draak.dtsindexaf07da240be0..668e246dfc5d100644arch/arm64/boot/dts/renesas/r8a77995-draak.dts +51
-0@@ -27,6 +27,38 @@ stdout-path = "serial0:115200n8"; }; + vga { + compatible = "vga-connector"; + + port { + vga_in: endpoint { + remote-endpoint = <&adv7123_out>; + }; + }; + }; + + vga-encoder { + compatible = "adi,adv7123"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7123_in: endpoint { + remote-endpoint = <&du_out_rgb>; + }; + }; + port@1 { + reg = <1>; + adv7123_out: endpoint { + remote-endpoint = <&vga_in>; + }; + }; + }; + }; + memory@48000000 { device_type = "memory"; /* first 128MB is reserved for secure area. */@@ -46,6 +78,11 @@ }; }; + du_pins: du { + groups = "du_rgb888", "du_sync", "du_disp", "du_dotclkout0"; + function = "du"; + }; + i2c0_pins: i2c0 { groups = "i2c0"; function = "i2c0";@@ -95,6 +132,20 @@ status = "okay"; }; +&du { + pinctrl-0 = <&du_pins>; + pinctrl-names = "default"; + status = "okay"; + + ports { + port@0 { + endpoint { + remote-endpoint = <&adv7123_in>; + }; + }; + }; +}; + &ehci0 { status = "okay"; };
Signature · 3 lines
Regards, Laurent Pinchart
Re: [PATCH 6/8] arm64: dts: renesas: r8a77995-draak: Enable DU
Hi Laurent, Simon,
Quoted 7 lines · Laurent Pinchart
Hi Kieran,
Thank you for the patch.
Quoted 2 lines · On Thursday, 15 February 2018 10:38:21 EET Kieran Bingham wrote:
From: Kieran Bingham <[email protected]>
Quoted 7 lines
Quoted 3 lines
Enable the DU, providing only the VGA output for now.
Signed-off-by Kieran Bingham <[email protected]>Reviewed-by Laurent Pinchart <[email protected]>I assume Simon will take care of this patch.
That will be great, - One small caveat on this patch though:
Quoted 52 lines
Quoted 52 lines
--- arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 51 +++++++++++++++++++++++ 1 file changed, 51 insertions(+)(quoted diff) +0
-0
b/arch/arm64/boot/dts/renesas/r8a77995-draak.dtsindexaf07da240be0..668e246dfc5d100644arch/arm64/boot/dts/renesas/r8a77995-draak.dts +32
-0@@ -27,6 +27,38 @@ stdout-path = "serial0:115200n8"; }; + vga { + compatible = "vga-connector"; + + port { + vga_in: endpoint { + remote-endpoint = <&adv7123_out>; + }; + }; + }; + + vga-encoder { + compatible = "adi,adv7123"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + adv7123_in: endpoint { + remote-endpoint = <&du_out_rgb>; + }; + }; + port at 1 { + reg = <1>; + adv7123_out: endpoint { + remote-endpoint = <&vga_in>; + }; + }; + }; + }; + memory at 48000000 { device_type = "memory"; /* first 128MB is reserved for secure area. */@@ -46,6 +78,11 @@ }; };
Quoted 2 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts line 82
Quoted 2 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +2
-0+ du_pins: du { + groups = "du_rgb888", "du_sync", "du_disp", "du_dotclkout0";
The du_dotclkout0 is named differently in Uli's patch. (Of course I believe my version is correct, but there is some precedent set it would seem).
Anyway, If Uli's version of the PFC is accepted (Which I'm sure it will be), then I will have to re-spin this patch with the 'different' "du_clk_out_0" value in the groups.
--
Kieran
Quoted 29 lines
Quoted 27 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +17
-0+ function = "du"; + }; + i2c0_pins: i2c0 { groups = "i2c0"; function = "i2c0";@@ -95,6 +132,20 @@ status = "okay"; }; +&du { + pinctrl-0 = <&du_pins>; + pinctrl-names = "default"; + status = "okay"; + + ports { + port at 0 { + endpoint { + remote-endpoint = <&adv7123_in>; + }; + }; + }; +}; + &ehci0 { status = "okay"; };
Re: [PATCH 6/8] arm64: dts: renesas: r8a77995-draak: Enable DU
Quoted 79 lines · Kieran Bingham
Hi Laurent, Simon,
Quoted 7 lines · Laurent Pinchart
Hi Kieran,
Thank you for the patch.
Quoted 2 lines · On Thursday, 15 February 2018 10:38:21 EET Kieran Bingham wrote:
From: Kieran Bingham <[email protected]>
Quoted 7 lines
Quoted 3 lines
Enable the DU, providing only the VGA output for now.
Signed-off-by Kieran Bingham <[email protected]>Reviewed-by Laurent Pinchart <[email protected]>I assume Simon will take care of this patch.
That will be great, - One small caveat on this patch though:
Quoted 52 lines
Quoted 52 lines
--- arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 51 +++++++++++++++++++++++ 1 file changed, 51 insertions(+)(quoted diff) +0
-0
b/arch/arm64/boot/dts/renesas/r8a77995-draak.dtsindexaf07da240be0..668e246dfc5d100644arch/arm64/boot/dts/renesas/r8a77995-draak.dts +32
-0@@ -27,6 +27,38 @@ stdout-path = "serial0:115200n8"; }; + vga { + compatible = "vga-connector"; + + port { + vga_in: endpoint { + remote-endpoint = <&adv7123_out>; + }; + }; + }; + + vga-encoder { + compatible = "adi,adv7123"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + adv7123_in: endpoint { + remote-endpoint = <&du_out_rgb>; + }; + }; + port at 1 { + reg = <1>; + adv7123_out: endpoint { + remote-endpoint = <&vga_in>; + }; + }; + }; + }; + memory at 48000000 { device_type = "memory"; /* first 128MB is reserved for secure area. */@@ -46,6 +78,11 @@ }; };Quoted 2 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts line 82
Quoted 2 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +2
-0+ du_pins: du { + groups = "du_rgb888", "du_sync", "du_disp", "du_dotclkout0";The
du_dotclkout0is named differently in Uli's patch. (Of course I believe my version is correct, but there is some precedent set it would seem).
Quoted 3 lines
Anyway, If Uli's version of the PFC is accepted (Which I'm sure it will be), then I will have to re-spin this patch with the 'different' "
du_clk_out_0" value in the groups.
Thanks, please repost once this has been shaken out.
PATCH v2 1/1 arm64: dts: renesas: r8a77995-draak: Enable DU
In reply to Kieran BinghamFrom: Kieran Bingham <[email protected]>
Enable the DU, providing only the VGA output for now.
---
Just a v2 update to fix the PFC name, and collect Laurent's RB tag. The remainder of the series will likely be postponed due to dependencies on LVDS changes etc.
v2:
- Update du_dot_clk_0 name to match Ulrich's PFC configuration.
arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 51 ++++++++++++++++++++++++++ 1 file changed, 51 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +51 -0
@@ -27,6 +27,38 @@ stdout-path = "serial0:115200n8"; }; + vga { + compatible = "vga-connector"; + + port { + vga_in: endpoint { + remote-endpoint = <&adv7123_out>; + }; + }; + }; + + vga-encoder { + compatible = "adi,adv7123"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + adv7123_in: endpoint { + remote-endpoint = <&du_out_rgb>; + }; + }; + port at 1 { + reg = <1>; + adv7123_out: endpoint { + remote-endpoint = <&vga_in>; + }; + }; + }; + }; + memory at 48000000 { device_type = "memory"; /* first 128MB is reserved for secure area. */
@@ -46,6 +78,11 @@ }; }; + du_pins: du { + groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0"; + function = "du"; + }; + i2c0_pins: i2c0 { groups = "i2c0"; function = "i2c0";
@@ -95,6 +132,20 @@ status = "okay"; }; +&du { + pinctrl-0 = <&du_pins>; + pinctrl-names = "default"; + status = "okay"; + + ports { + port at 0 { + endpoint { + remote-endpoint = <&adv7123_in>; + }; + }; + }; +}; + &ehci0 { status = "okay"; };
Signature · 1 line
2.7.4
Simon Horman
AppliedRe: [PATCH v2] arm64: dts: renesas: r8a77995-draak: Enable DU
Quoted 6 lines · Kieran Bingham
From: Kieran Bingham <[email protected]>
Enable the DU, providing only the VGA output for now.
Signed-off-by Kieran Bingham <[email protected]>Reviewed-by Laurent Pinchart <[email protected]>
Quoted 8 lines
---
Just a v2 update to fix the PFC name, and collect Laurent's RB tag. The remainder of the series will likely be postponed due to dependencies on LVDS changes etc.
v2:
- Updatedu_dot_clk_0name to match Ulrich's PFC configuration.
Thanks, applied with s/r8a77995-// adjustment to the subject.
PATCH 7/8 arm64: dts: renesas: r8a77995-draak: Add HDMI Out through ADV7511
In reply to Kieran BinghamFrom: Kieran Bingham <[email protected]>
Provide a device node for the ADV7511 as found on the Draak D3 platform.
The ADV7511 is connected to the DU through a parallel mux chip, and is configurable in hardware whether it is connected to LVDS0 or LVDS1.
Connect through to LVDS0 as a default implementation.
--- arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 56 ++++++++++++++++++++++++++ 1 file changed, 56 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +56 -0
@@ -27,6 +27,17 @@ stdout-path = "serial0:115200n8"; }; + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_out: endpoint { + remote-endpoint = <&adv7511_out>; + }; + }; + }; + vga { compatible = "vga-connector";
@@ -124,6 +135,39 @@ reg = <0x50>; pagesize = <8>; }; + + hdmi at 39 { + compatible = "adi,adv7511w"; + reg = <0x39>, <0x3f>, <0x38>, <0x3c>; + reg-names = "main", "edid", "packet", "cec"; + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_LEVEL_LOW>; + + adi,input-depth = <8>; + adi,input-colorspace = "rgb"; + adi,input-clock = "1x"; + adi,input-style = <1>; + adi,input-justification = "evenly"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + adv7511_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + + port at 1 { + reg = <1>; + adv7511_out: endpoint { + remote-endpoint = <&hdmi_con_out>; + }; + }; + }; + }; }; &i2c1 {
@@ -146,6 +190,18 @@ }; }; +&lvds0 { + status = "okay"; + + ports { + port at 1 { + endpoint { + remote-endpoint = <&adv7511_in>; + }; + }; + }; +}; + &ehci0 { status = "okay"; };
Signature · 1 line
2.7.4
Laurent Pinchart
reviewerRe: [PATCH 7/8] arm64: dts: renesas: r8a77995-draak: Add HDMI Out through ADV7511
Hi Kieran,
Thank you for the patch.
Quoted 8 lines · On Thursday, 15 February 2018 10:38:22 EET Kieran Bingham wrote:
From: Kieran Bingham <[email protected]>
Provide a device node for the ADV7511 as found on the Draak D3 platform.
The ADV7511 is connected to the DU through a parallel mux chip, and is configurable in hardware whether it is connected to LVDS0 or LVDS1.
Connect through to LVDS0 as a default implementation.
You need to model the LVDS decoder in DT too. I know that no driver and no DT bindings are available at the moment, and I'm aware that this patch enables the HDMI output on the Draak board, but I don't think it's upstreamable as-is.
Quoted 87 lines
Signed-off-by Kieran Bingham <[email protected]>--- arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 56 +++++++++++++++++++++++ 1 file changed, 56 insertions(+)(quoted diff) +0
-0
b/arch/arm64/boot/dts/renesas/r8a77995-draak.dtsindex668e246dfc5d..df0c7773cb7d100644arch/arm64/boot/dts/renesas/r8a77995-draak.dts +56
-0@@ -27,6 +27,17 @@ stdout-path = "serial0:115200n8"; }; + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_out: endpoint { + remote-endpoint = <&adv7511_out>; + }; + }; + }; + vga { compatible = "vga-connector";@@ -124,6 +135,39 @@ reg = <0x50>; pagesize = <8>; }; + + hdmi@39 { + compatible = "adi,adv7511w"; + reg = <0x39>, <0x3f>, <0x38>, <0x3c>; + reg-names = "main", "edid", "packet", "cec"; + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_LEVEL_LOW>; + + adi,input-depth = <8>; + adi,input-colorspace = "rgb"; + adi,input-clock = "1x"; + adi,input-style = <1>; + adi,input-justification = "evenly"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7511_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + + port@1 { + reg = <1>; + adv7511_out: endpoint { + remote-endpoint = <&hdmi_con_out>; + }; + }; + }; + }; }; &i2c1 {@@ -146,6 +190,18 @@ }; }; +&lvds0 { + status = "okay"; + + ports { + port@1 { + endpoint { + remote-endpoint = <&adv7511_in>; + }; + }; + }; +}; + &ehci0 { status = "okay"; };
Signature · 3 lines
Regards, Laurent Pinchart
Re: [PATCH 7/8] arm64: dts: renesas: r8a77995-draak: Add HDMI Out through ADV7511
Quoted 9 lines · Laurent Pinchart
Hi Kieran,
Thank you for the patch.
Quoted 4 lines · On Thursday, 15 February 2018 10:38:22 EET Kieran Bingham wrote:
From: Kieran Bingham <[email protected]>
Provide a device node for the ADV7511 as found on the Draak D3 platform.
Quoted 8 lines
Quoted 4 lines
The ADV7511 is connected to the DU through a parallel mux chip, and is configurable in hardware whether it is connected to LVDS0 or LVDS1.
Connect through to LVDS0 as a default implementation.
You need to model the LVDS decoder in DT too. I know that no driver and no DT bindings are available at the moment, and I'm aware that this patch enables the HDMI output on the Draak board, but I don't think it's upstreamable as-is.
Thanks, I've marked this as "Changes Requested".
Re: [PATCH 7/8] arm64: dts: renesas: r8a77995-draak: Add HDMI Out through ADV7511
In reply to Laurent PinchartHi Laurent,
Quoted 9 lines · Laurent Pinchart
Hi Kieran,
Thank you for the patch.
Quoted 4 lines · On Thursday, 15 February 2018 10:38:22 EET Kieran Bingham wrote:
From: Kieran Bingham <[email protected]>
Provide a device node for the ADV7511 as found on the Draak D3 platform.
Quoted 8 lines
Quoted 4 lines
The ADV7511 is connected to the DU through a parallel mux chip, and is configurable in hardware whether it is connected to LVDS0 or LVDS1.
Connect through to LVDS0 as a default implementation.
You need to model the LVDS decoder in DT too. I know that no driver and no DT bindings are available at the moment, and I'm aware that this patch enables the HDMI output on the Draak board, but I don't think it's upstreamable as-is.
Ok, understood. - I'll drop this patch for now until we can schedule time to dedicate to looking into this.
I'm sure the archive's will hold on to this patch for us as a starting point :-)
--
Regards
Kieran
Quoted 90 lines
Quoted 88 lines
Signed-off-by Kieran Bingham <[email protected]>--- arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 56 +++++++++++++++++++++++ 1 file changed, 56 insertions(+)(quoted diff) +0
-0
b/arch/arm64/boot/dts/renesas/r8a77995-draak.dtsindex668e246dfc5d..df0c7773cb7d100644arch/arm64/boot/dts/renesas/r8a77995-draak.dts +56
-0@@ -27,6 +27,17 @@ stdout-path = "serial0:115200n8"; }; + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_out: endpoint { + remote-endpoint = <&adv7511_out>; + }; + }; + }; + vga { compatible = "vga-connector";@@ -124,6 +135,39 @@ reg = <0x50>; pagesize = <8>; }; + + hdmi at 39 { + compatible = "adi,adv7511w"; + reg = <0x39>, <0x3f>, <0x38>, <0x3c>; + reg-names = "main", "edid", "packet", "cec"; + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_LEVEL_LOW>; + + adi,input-depth = <8>; + adi,input-colorspace = "rgb"; + adi,input-clock = "1x"; + adi,input-style = <1>; + adi,input-justification = "evenly"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + adv7511_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + + port at 1 { + reg = <1>; + adv7511_out: endpoint { + remote-endpoint = <&hdmi_con_out>; + }; + }; + }; + }; }; &i2c1 {@@ -146,6 +190,18 @@ }; }; +&lvds0 { + status = "okay"; + + ports { + port at 1 { + endpoint { + remote-endpoint = <&adv7511_in>; + }; + }; + }; +}; + &ehci0 { status = "okay"; };
PATCH 8/8 arm64: dts: renesas: r8a77995-draak: Add ADV7612
In reply to Kieran BinghamFrom: Kieran Bingham <[email protected]>
Provide a node for the ADV7612. There is no VIN support yet, so this node will only instantiate the device on the I2C bus for I2C address testing.
--- arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 43 ++++++++++++++++++++++++++ 1 file changed, 43 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +43 -0
@@ -27,6 +27,17 @@ stdout-path = "serial0:115200n8"; }; + hdmi-in { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&adv7612_in>; + }; + }; + }; + hdmi-out { compatible = "hdmi-connector"; type = "a";
@@ -168,6 +179,38 @@ }; }; }; + + hdmi-in at 4c { + compatible = "adi,adv7612"; + reg = <0x4c>, <0x5a>, <0x5b>, <0x5c>, <0x5d>, <0x5e>, <0x5f>, + <0x6a>, <0x6b>, <0x6c>, <0x6d>, <0x6e>, <0x6f>; + reg-names = "main", "avlink", "cec", "infoframe", "esdp", + "dpp", "afe", "rep", "edid", "hdmi", "test", + "cp", "vdp"; + + /* ADV7612_INTn connected only to test point CP56. */ + + default-input = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + adv7612_in: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; + }; + + port at 2 { + reg = <2>; + adv7612_out: endpoint { + // remote-endpoint = <&vin0ep2>; + }; + }; + }; + }; }; &i2c1 {
Signature · 1 line
2.7.4