Skip to contentSkip to conversation

Patch "net/mlx4_en: Change default QoS settings" has been added to the 4.15-stable tree

PATCH [email protected] 1 participant 1 message Apr 9, 2018

Subsystems (4)
lore
Share & tools
lore

[email protected]

author maintainer Applied
#0 lore raw

This is a note to let you know that I've just added the patch titled

net/mlx4_en: Change default QoS settings

to the 4.15-stable tree which can be found at:
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
net-mlx4_en-change-default-qos-settings.patch
and it can be found in the queue-4.15 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree, please let <[email protected]> know about it.

Quoted 1 line

From foo@baz Mon Apr 9 10:16:32 CEST 2018

From: Moni Shoua <[email protected]>
Date: Thu, 28 Dec 2017 16:26:11 +0200
Subject: net/mlx4_en: Change default QoS settings

From: Moni Shoua <[email protected]>

[ Upstream commit a42b63c1ac1986f17f71bc91a6b0aaa14d4dae71 ]

Change the default mapping between TC and TCG as follows:

Prio     |             TC/TCG
         |      from             to
         |    (set by FW)      (set by SW)
---------+-----------------------------------
0        |      0/0              0/7
1        |      1/0              0/6
2        |      2/0              0/5
3        |      3/0              0/4
4        |      4/0              0/3
5        |      5/0              0/2
6        |      6/0              0/1
7        |      7/0              0/0

These new settings cause that a pause frame for any prio stops traffic for all prios.

Fixes 564c274c3df0 ("net/mlx4_en: DCB QoS support")
---
 drivers/net/ethernet/mellanox/mlx4/en_dcb_nl.c |    5 +++++
 drivers/net/ethernet/mellanox/mlx4/en_netdev.c |    7 +++++++
 drivers/net/ethernet/mellanox/mlx4/mlx4_en.h   |    1 +
 3 files changed, 13 insertions(+)
drivers/net/ethernet/mellanox/mlx4/en_dcb_nl.c +5 -0
@@ -310,6 +310,7 @@ static int mlx4_en_ets_validate(struct m
 		}
 
 		switch (ets->tc_tsa[i]) {
+		case IEEE_8021QAZ_TSA_VENDOR:
 		case IEEE_8021QAZ_TSA_STRICT:
 			break;
 		case IEEE_8021QAZ_TSA_ETS:
@@ -347,6 +348,10 @@ static int mlx4_en_config_port_scheduler
 	/* higher TC means higher priority => lower pg */
 	for (i = IEEE_8021QAZ_MAX_TCS - 1; i >= 0; i--) {
 		switch (ets->tc_tsa[i]) {
+		case IEEE_8021QAZ_TSA_VENDOR:
+			pg[i] = MLX4_EN_TC_VENDOR;
+			tc_tx_bw[i] = MLX4_EN_BW_MAX;
+			break;
 		case IEEE_8021QAZ_TSA_STRICT:
 			pg[i] = num_strict++;
 			tc_tx_bw[i] = MLX4_EN_BW_MAX;
drivers/net/ethernet/mellanox/mlx4/en_netdev.c +7 -0
@@ -3336,6 +3336,13 @@ int mlx4_en_init_netdev(struct mlx4_en_d
 	priv->msg_enable = MLX4_EN_MSG_LEVEL;
 #ifdef CONFIG_MLX4_EN_DCB
 	if (!mlx4_is_slave(priv->mdev->dev)) {
+		u8 prio;
+
+		for (prio = 0; prio < IEEE_8021QAZ_MAX_TCS; ++prio) {
+			priv->ets.prio_tc[prio] = prio;
+			priv->ets.tc_tsa[prio]  = IEEE_8021QAZ_TSA_VENDOR;
+		}
+
 		priv->dcbx_cap = DCB_CAP_DCBX_VER_CEE | DCB_CAP_DCBX_HOST |
 			DCB_CAP_DCBX_VER_IEEE;
 		priv->flags |= MLX4_EN_DCB_ENABLED;
drivers/net/ethernet/mellanox/mlx4/mlx4_en.h +1 -0
@@ -479,6 +479,7 @@ struct mlx4_en_frag_info {
 #define MLX4_EN_BW_MIN 1
 #define MLX4_EN_BW_MAX 100 /* Utilize 100% of the line */
 
+#define MLX4_EN_TC_VENDOR 0
 #define MLX4_EN_TC_ETS 7
 
 enum dcb_pfc_type {

Patches currently in stable-queue which might be from [email protected] are

queue-4.15/net-mlx4_en-change-default-qos-settings.patch