Kryo CPU scaling driver
Subsystems (4)
v13 cover Kryo CPU scaling driver
[v13]
* Addressed comment from Sudeep about DT compatible check on init
[v12]
* Addressed comments from Sudeep and Viresh about the single init
[v11]
* Addressed comment from Russel about device_node reference
* Addressed comment from Sudeep about the late_initcall
* Transformed init into probe to take care of deferals
[v10]
* Split the series into domains
* Addressed comments from Viresh and Sudeep about logical CPU numbering.
The qcom-cpufreq-kryo driver is aimed to support different SOC versions. The driver reads eFuse information and chooses the required OPP subset by passing the OPP supported-hw parameter.
The series depends on the series from Viresh:
https://patchwork.kernel.org/patch/10418139/
The previous spin was here:
https://patchwork.kernel.org/patch/10423137/
Ilia Lin (2):
cpufreq: Add Kryo CPU scaling driver
dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu
.../devicetree/bindings/opp/kryo-cpufreq.txt | 680 +++++++++++++++++++++ drivers/cpufreq/Kconfig.arm | 10 + drivers/cpufreq/Makefile | 1 + drivers/cpufreq/cpufreq-dt-platdev.c | 3 + drivers/cpufreq/qcom-cpufreq-kryo.c | 206 +++++++ 5 files changed, 900 insertions(+) create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c
Signature · 1 line
1.9.1
PATCH v13 1/2 cpufreq: Add Kryo CPU scaling driver
In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors, the CPU frequency subset and voltage value of each OPP varies based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables defines the voltage and frequency value based on the msm-id in SMEM and speedbin blown in the efuse combination.
The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of operating-points-v2 table when it is parsed by the OPP framework.
Signed-off-by Ilia Lin <[email protected]>
--- drivers/cpufreq/Kconfig.arm | 10 ++ drivers/cpufreq/Makefile | 1 + drivers/cpufreq/cpufreq-dt-platdev.c | 3 + drivers/cpufreq/qcom-cpufreq-kryo.c | 206 +++++++++++++++++++++++++++++++++++ 4 files changed, 220 insertions(+) create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c
drivers/cpufreq/Kconfig.arm +10 -0
@@ -124,6 +124,16 @@ config ARM_OMAP2PLUS_CPUFREQ depends on ARCH_OMAP2PLUS default ARCH_OMAP2PLUS +config ARM_QCOM_CPUFREQ_KRYO + bool "Qualcomm Kryo based CPUFreq" + depends on QCOM_QFPROM + depends on QCOM_SMEM + select PM_OPP + help + This adds the CPUFreq driver for Qualcomm Kryo SoC based boards. + + If in doubt, say N. + config ARM_S3C_CPUFREQ bool help
drivers/cpufreq/Makefile +1 -0
@@ -65,6 +65,7 @@ obj-$(CONFIG_MACH_MVEBU_V7) += mvebu-cpufreq.o obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ) += omap-cpufreq.o obj-$(CONFIG_ARM_PXA2xx_CPUFREQ) += pxa2xx-cpufreq.o obj-$(CONFIG_PXA3xx) += pxa3xx-cpufreq.o +obj-$(CONFIG_ARM_QCOM_CPUFREQ_KRYO) += qcom-cpufreq-kryo.o obj-$(CONFIG_ARM_S3C2410_CPUFREQ) += s3c2410-cpufreq.o obj-$(CONFIG_ARM_S3C2412_CPUFREQ) += s3c2412-cpufreq.o obj-$(CONFIG_ARM_S3C2416_CPUFREQ) += s3c2416-cpufreq.o
drivers/cpufreq/cpufreq-dt-platdev.c +3 -0
@@ -118,6 +118,9 @@ { .compatible = "nvidia,tegra124", }, + { .compatible = "qcom,apq8096", }, + { .compatible = "qcom,msm8996", }, + { .compatible = "st,stih407", }, { .compatible = "st,stih410", },
drivers/cpufreq/qcom-cpufreq-kryo.c new file +206 -0
206 lines not on this page · raw message
Signature · 1 line
1.9.1
Viresh Kumar
maintainerRe: [PATCH v13 1/2] cpufreq: Add Kryo CPU scaling driver
Quoted 9 lines · Ilia Lin
drivers/cpufreq/qcom-cpufreq-kryo.c new file +9
-0+static int __init qcom_cpufreq_kryo_init (void ) +{ +struct device_node *np; +struct device *cpu_dev; +int ret; + + cpu_dev =get_cpu_device (0 ); +if (NULL == cpu_dev) + ret = -ENODEV ;
drivers/cpufreq/qcom-cpufreq-kryo.c line 190
Quoted 10 lines
drivers/cpufreq/qcom-cpufreq-kryo.c new file +10
-0+ + np =dev_pm_opp_of_get_opp_desc_node (cpu_dev); +if (IS_ERR (np)) +return PTR_ERR (np); + + ret =of_device_is_compatible (np,"operating-points-v2-kryo-cpu" ); +of_node_put (np); +if (!ret) +return -ENOENT ; +
I hate the fact that it is taking so long to get done with this. But can't you just check machine compatibility instead of this complicated setup to check OPP node ? Like:
if (!of_device_is_compatible("qcom,apq8096") &&
!of_device_is_compatible("qcom,msm8996"))
return;And please see if you can add an entry in MAINTAINERS and add your working email id there.
Signature · 1 line
viresh
Re: [PATCH v13 1/2] cpufreq: Add Kryo CPU scaling driver
Quoted 27 lines · Viresh Kumar
Quoted 9 lines · Ilia Lin
drivers/cpufreq/qcom-cpufreq-kryo.c new file +9
-0+static int __init qcom_cpufreq_kryo_init (void ) +{ +struct device_node *np; +struct device *cpu_dev; +int ret; + + cpu_dev =get_cpu_device (0 ); +if (NULL == cpu_dev) + ret = -ENODEV ;drivers/cpufreq/qcom-cpufreq-kryo.c line 190
Quoted 10 lines
drivers/cpufreq/qcom-cpufreq-kryo.c new file +10
-0+ + np =dev_pm_opp_of_get_opp_desc_node (cpu_dev); +if (IS_ERR (np)) +return PTR_ERR (np); + + ret =of_device_is_compatible (np,"operating-points-v2-kryo-cpu" ); +of_node_put (np); +if (!ret) +return -ENOENT ; +I hate the fact that it is taking so long to get done with this. But can't you
just check machine compatibility instead of this complicated setup to check OPP
node ? Like:
Quoted 3 lines
if (!of_device_is_compatible("qcom,apq8096") &&
!of_device_is_compatible("qcom,msm8996"))
return;I have to check the "operating-points-v2-kryo-cpu" anyway, so I moved it from probe to the init.
Quoted 4 lines
And please see if you can add an entry in
MAINTAINERSand add your working email
id there.
Sure. Should this be part of the patch itself?
Viresh Kumar
maintainerRe: [PATCH v13 1/2] cpufreq: Add Kryo CPU scaling driver
Quoted 30 lines · Ilia Lin
Quoted 27 lines · Viresh Kumar
Quoted 9 lines · Ilia Lin
drivers/cpufreq/qcom-cpufreq-kryo.c new file +9
-0+static int __init qcom_cpufreq_kryo_init (void ) +{ +struct device_node *np; +struct device *cpu_dev; +int ret; + + cpu_dev =get_cpu_device (0 ); +if (NULL == cpu_dev) + ret = -ENODEV ;drivers/cpufreq/qcom-cpufreq-kryo.c line 190
Quoted 10 lines
drivers/cpufreq/qcom-cpufreq-kryo.c new file +10
-0+ + np =dev_pm_opp_of_get_opp_desc_node (cpu_dev); +if (IS_ERR (np)) +return PTR_ERR (np); + + ret =of_device_is_compatible (np,"operating-points-v2-kryo-cpu" ); +of_node_put (np); +if (!ret) +return -ENOENT ; +I hate the fact that it is taking so long to get done with this. But can't you
just check machine compatibility instead of this complicated setup to check OPP
node ? Like:
Quoted 5 lines
Quoted 3 lines
if (!of_device_is_compatible("qcom,apq8096") && !of_device_is_compatible("qcom,msm8996")) return;I have to check the "operating-points-v2-kryo-cpu" anyway, so I moved it from probe to the init.
Okay, leave it as is then. Don't send anything yet and wait for Sudeep to respond.
Quoted 6 lines
Quoted 4 lines
And please see if you can add an entry in
MAINTAINERSand add your working email
id there.Sure. Should this be part of the patch itself?
If you need to send another version of this series, then add it to this patch itself. Else send it separately and don't resend this stuff.
Signature · 1 line
viresh
Re: [PATCH v13 1/2] cpufreq: Add Kryo CPU scaling driver
Quoted 31 lines · Viresh Kumar
Quoted 30 lines · Ilia Lin
Quoted 27 lines · Viresh Kumar
Quoted 9 lines · Ilia Lin
drivers/cpufreq/qcom-cpufreq-kryo.c new file +9
-0+static int __init qcom_cpufreq_kryo_init (void ) +{ +struct device_node *np; +struct device *cpu_dev; +int ret; + + cpu_dev =get_cpu_device (0 ); +if (NULL == cpu_dev) + ret = -ENODEV ;drivers/cpufreq/qcom-cpufreq-kryo.c line 190
Quoted 10 lines
drivers/cpufreq/qcom-cpufreq-kryo.c new file +10
-0+ + np =dev_pm_opp_of_get_opp_desc_node (cpu_dev); +if (IS_ERR (np)) +return PTR_ERR (np); + + ret =of_device_is_compatible (np,"operating-points-v2-kryo-cpu" ); +of_node_put (np); +if (!ret) +return -ENOENT ; +I hate the fact that it is taking so long to get done with this. But can't you
just check machine compatibility instead of this complicated setup to check OPP
node ? Like:
Quoted 9 lines
Quoted 5 lines
Quoted 3 lines
if (!of_device_is_compatible("qcom,apq8096") && !of_device_is_compatible("qcom,msm8996")) return;I have to check the "operating-points-v2-kryo-cpu" anyway, so I moved it from probe to the init.
Okay, leave it as is then. Don't send anything yet and wait for Sudeep to respond.
I have already mentioned that I can't suggest since I don't have much knowledge on QCOM PM. I see lots of patches flying around these days with multiple people doing same things in different ways. That's why I suggested Ilia to check with Taniya or Saravana or SBoyd to see what's the best thing to do in this context. I don't prefer using OPP compatible and would go with machine compatibility as you suggested. But I am fine with OPP, just wanted to make sure it won't clash with anything else.
Signature · 2 lines
Regards, Sudeep
PATCH v13 2/2 dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu
In reply to Ilia LinThe qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of operating-points-v2 table when it is parsed by the OPP framework.
This change adds documentation for the DT bindings.
The "operating-points-v2-kryo-cpu" DT extends the "operating-points-v2" with following parameters:
- nvmem-cells (NVMEM area containig the speedbin information)
- opp-supported-hw: A single 32 bit bitmap value, representing compatible HW:
0: MSM8996 V3, speedbin 0 1: MSM8996 V3, speedbin 1 2: MSM8996 V3, speedbin 2 3: unused 4: MSM8996 SG, speedbin 0 5: MSM8996 SG, speedbin 1 6: MSM8996 SG, speedbin 2 7-31: unused
Signed-off-by Ilia Lin <[email protected]>
Reviewed-by Rob Herring <[email protected]>
Acked-by Viresh Kumar <[email protected]>
--- .../devicetree/bindings/opp/kryo-cpufreq.txt | 680 +++++++++++++++++++++ 1 file changed, 680 insertions(+) create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
Documentation/devicetree/bindings/opp/kryo-cpufreq.txt new file +680 -0
@@ -0,0 +1,680 @@ +Qualcomm Technologies, Inc. KRYO CPUFreq and OPP bindings +=================================== + +In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996 +that have KRYO processors, the CPU ferequencies subset and voltage value +of each OPP varies based on the silicon variant in use. +Qualcomm Technologies, Inc. Process Voltage Scaling Tables +defines the voltage and frequency value based on the msm-id in SMEM +and speedbin blown in the efuse combination. +The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC +to provide the OPP framework with required information (existing HW bitmap). +This is used to determine the voltage and frequency value for each OPP of +operating-points-v2 table when it is parsed by the OPP framework. + +Required properties: +-------------------- +In 'cpus' nodes: +- operating-points-v2: Phandle to the operating-points-v2 table to use. + +In 'operating-points-v2' table: +- compatible: Should be + - 'operating-points-v2-kryo-cpu' for apq8096 and msm8996. +- nvmem-cells: A phandle pointing to a nvmem-cells node representing the + efuse registers that has information about the + speedbin that is used to select the right frequency/voltage + value pair. + Please refer the for nvmem-cells + bindings Documentation/devicetree/bindings/nvmem/nvmem.txt + and also examples below. + +In every OPP node: +- opp-supported-hw: A single 32 bit bitmap value, representing compatible HW. + Bitmap: + 0: MSM8996 V3, speedbin 0 + 1: MSM8996 V3, speedbin 1 + 2: MSM8996 V3, speedbin 2 + 3: unused + 4: MSM8996 SG, speedbin 0 + 5: MSM8996 SG, speedbin 1 + 6: MSM8996 SG, speedbin 2 + 7-31: unused + +Example 1: +--------- + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x0>; + enable-method = "psci"; + clocks = <&kryocc 0>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + compatible = "cache"; + cache-level = <2>; + }; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x1>; + enable-method = "psci"; + clocks = <&kryocc 0>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_0>; + }; + + CPU2: cpu@100 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x100>; + enable-method = "psci"; + clocks = <&kryocc 1>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster1_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_1>; + L2_1: l2-cache { + compatible = "cache"; + cache-level = <2>; + }; + }; + + CPU3: cpu@101 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x101>; + enable-method = "psci"; + clocks = <&kryocc 1>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster1_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_1>; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&CPU0>; + }; + + core1 { + cpu = <&CPU1>; + }; + }; + + cluster1 { + core0 { + cpu = <&CPU2>; + }; + + core1 { + cpu = <&CPU3>; + }; + }; + }; + }; + + cluster0_opp: opp_table0 { + compatible = "operating-points-v2-kryo-cpu"; + nvmem-cells = <&speedbin_efuse>; + opp-shared; + + opp-307200000 { + opp-hz = /bits/ 64 <307200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x77>; + clock-latency-ns = <200000>; + }; + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-422400000 { + opp-hz = /bits/ 64 <422400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-460800000 { + opp-hz = /bits/ 64 <460800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-480000000 { + opp-hz = /bits/ 64 <480000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-537600000 { + opp-hz = /bits/ 64 <537600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-556800000 { + opp-hz = /bits/ 64 <556800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-614400000 { + opp-hz = /bits/ 64 <614400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-652800000 { + opp-hz = /bits/ 64 <652800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-691200000 { + opp-hz = /bits/ 64 <691200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-729600000 { + opp-hz = /bits/ 64 <729600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-768000000 { + opp-hz = /bits/ 64 <768000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-844800000 { + opp-hz = /bits/ 64 <844800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x77>; + clock-latency-ns = <200000>; + }; + opp-902400000 { + opp-hz = /bits/ 64 <902400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-960000000 { + opp-hz = /bits/ 64 <960000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-979200000 { + opp-hz = /bits/ 64 <979200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1036800000 { + opp-hz = /bits/ 64 <1036800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1056000000 { + opp-hz = /bits/ 64 <1056000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1113600000 { + opp-hz = /bits/ 64 <1113600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1132800000 { + opp-hz = /bits/ 64 <1132800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1190400000 { + opp-hz = /bits/ 64 <1190400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1209600000 { + opp-hz = /bits/ 64 <1209600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1228800000 { + opp-hz = /bits/ 64 <1228800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1286400000 { + opp-hz = /bits/ 64 <1286400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1324800000 { + opp-hz = /bits/ 64 <1324800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x5>; + clock-latency-ns = <200000>; + }; + opp-1363200000 { + opp-hz = /bits/ 64 <1363200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x72>; + clock-latency-ns = <200000>; + }; + opp-1401600000 { + opp-hz = /bits/ 64 <1401600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x5>; + clock-latency-ns = <200000>; + }; + opp-1440000000 { + opp-hz = /bits/ 64 <1440000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1478400000 { + opp-hz = /bits/ 64 <1478400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-1497600000 { + opp-hz = /bits/ 64 <1497600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x4>; + clock-latency-ns = <200000>; + }; + opp-1516800000 { + opp-hz = /bits/ 64 <1516800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1593600000 { + opp-hz = /bits/ 64 <1593600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x71>; + clock-latency-ns = <200000>; + }; + opp-1996800000 { + opp-hz = /bits/ 64 <1996800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x20>; + clock-latency-ns = <200000>; + }; + opp-2188800000 { + opp-hz = /bits/ 64 <2188800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x10>; + clock-latency-ns = <200000>; + }; + }; + + cluster1_opp: opp_table1 { + compatible = "operating-points-v2-kryo-cpu"; + nvmem-cells = <&speedbin_efuse>; + opp-shared; + + opp-307200000 { + opp-hz = /bits/ 64 <307200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x77>; + clock-latency-ns = <200000>; + }; + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-403200000 { + opp-hz = /bits/ 64 <403200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-460800000 { + opp-hz = /bits/ 64 <460800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-480000000 { + opp-hz = /bits/ 64 <480000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-537600000 { + opp-hz = /bits/ 64 <537600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-556800000 { + opp-hz = /bits/ 64 <556800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-614400000 { + opp-hz = /bits/ 64 <614400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-652800000 { + opp-hz = /bits/ 64 <652800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-691200000 { + opp-hz = /bits/ 64 <691200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-729600000 { + opp-hz = /bits/ 64 <729600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-748800000 { + opp-hz = /bits/ 64 <748800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-806400000 { + opp-hz = /bits/ 64 <806400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-825600000 { + opp-hz = /bits/ 64 <825600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-883200000 { + opp-hz = /bits/ 64 <883200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-902400000 { + opp-hz = /bits/ 64 <902400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-940800000 { + opp-hz = /bits/ 64 <940800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-979200000 { + opp-hz = /bits/ 64 <979200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1036800000 { + opp-hz = /bits/ 64 <1036800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1056000000 { + opp-hz = /bits/ 64 <1056000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1113600000 { + opp-hz = /bits/ 64 <1113600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1132800000 { + opp-hz = /bits/ 64 <1132800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1190400000 { + opp-hz = /bits/ 64 <1190400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1209600000 { + opp-hz = /bits/ 64 <1209600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1248000000 { + opp-hz = /bits/ 64 <1248000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1286400000 { + opp-hz = /bits/ 64 <1286400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1324800000 { + opp-hz = /bits/ 64 <1324800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1363200000 { + opp-hz = /bits/ 64 <1363200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1401600000 { + opp-hz = /bits/ 64 <1401600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1440000000 { + opp-hz = /bits/ 64 <1440000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1478400000 { + opp-hz = /bits/ 64 <1478400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1516800000 { + opp-hz = /bits/ 64 <1516800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1555200000 { + opp-hz = /bits/ 64 <1555200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1593600000 { + opp-hz = /bits/ 64 <1593600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1632000000 { + opp-hz = /bits/ 64 <1632000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1670400000 { + opp-hz = /bits/ 64 <1670400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1708800000 { + opp-hz = /bits/ 64 <1708800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1747200000 { + opp-hz = /bits/ 64 <1747200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1785600000 { + opp-hz = /bits/ 64 <1785600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1804800000 { + opp-hz = /bits/ 64 <1804800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x6>; + clock-latency-ns = <200000>; + }; + opp-1824000000 { + opp-hz = /bits/ 64 <1824000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x71>; + clock-latency-ns = <200000>; + }; + opp-1900800000 { + opp-hz = /bits/ 64 <1900800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x74>; + clock-latency-ns = <200000>; + }; + opp-1920000000 { + opp-hz = /bits/ 64 <1920000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-1977600000 { + opp-hz = /bits/ 64 <1977600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x30>; + clock-latency-ns = <200000>; + }; + opp-1996800000 { + opp-hz = /bits/ 64 <1996800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-2054400000 { + opp-hz = /bits/ 64 <2054400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x30>; + clock-latency-ns = <200000>; + }; + opp-2073600000 { + opp-hz = /bits/ 64 <2073600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-2150400000 { + opp-hz = /bits/ 64 <2150400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x31>; + clock-latency-ns = <200000>; + }; + opp-2246400000 { + opp-hz = /bits/ 64 <2246400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x10>; + clock-latency-ns = <200000>; + }; + opp-2342400000 { + opp-hz = /bits/ 64 <2342400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x10>; + clock-latency-ns = <200000>; + }; + }; + +.... + +reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; +.... + smem_mem: smem-mem@86000000 { + reg = <0x0 0x86000000 0x0 0x200000>; + no-map; + }; +.... +}; + +smem { + compatible = "qcom,smem"; + memory-region = <&smem_mem>; + hwlocks = <&tcsr_mutex 3>; +}; + +soc { +.... + qfprom: qfprom@74000 { + compatible = "qcom,qfprom"; + reg = <0x00074000 0x8ff>; + #address-cells = <1>; + #size-cells = <1>; + .... + speedbin_efuse: speedbin@133 { + reg = <0x133 0x1>; + bits = <5 3>; + }; + }; +};
Signature · 1 line
1.9.1