Skip to contentSkip to conversation

Kryo CPU scaling driver

PATCH Superseded Ilia Lin 4 participants 7 messages May 25, 2018 – May 30, 2018

Subsystems (4)
Device tree bindings Arm Qualcomm mailing list CPU frequency scaling framework Operating performance points (OPP)

v14 of 15 Superseded Latest is v15 →

lore
Share & tools
lore

Ilia Lin

author
#0 lore raw

v14 cover Kryo CPU scaling driver

[v14]
* Addressed comment from Sudeep about DT compatible
* Added MAINTAINERS entry

[v13]
* Addressed comment from Sudeep about DT compatible check on init

[v12]
* Addressed comments from Sudeep and Viresh about the single init

[v11]
* Addressed comment from Russel about device_node reference
* Addressed comment from Sudeep about the late_initcall
* Transformed init into probe to take care of deferals

[v10]
* Split the series into domains
* Addressed comments from Viresh and Sudeep about logical CPU numbering.

The qcom-cpufreq-kryo driver is aimed to support different SOC versions. The driver reads eFuse information and chooses the required OPP subset by passing the OPP supported-hw parameter.

The series depends on the series from Viresh:
https://patchwork.kernel.org/patch/10418139/

The previous spin was here:
https://patchwork.kernel.org/patch/10424949/

Ilia Lin (2):
cpufreq: Add Kryo CPU scaling driver
dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu

 .../devicetree/bindings/opp/kryo-cpufreq.txt       | 680 +++++++++++++++++++++
 MAINTAINERS                                        |   7 +
 drivers/cpufreq/Kconfig.arm                        |  10 +
 drivers/cpufreq/Makefile                           |   1 +
 drivers/cpufreq/cpufreq-dt-platdev.c               |   3 +
 drivers/cpufreq/qcom-cpufreq-kryo.c                | 206 +++++++
 6 files changed, 907 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
 create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c
Signature · 1 line
1.9.1
author
#1 lore raw

PATCH v14 1/2 cpufreq: Add Kryo CPU scaling driver

In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors, the CPU frequency subset and voltage value of each OPP varies based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables defines the voltage and frequency value based on the msm-id in SMEM and speedbin blown in the efuse combination.
The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of operating-points-v2 table when it is parsed by the OPP framework.

Signed-off-by Ilia Lin <[email protected]>
---
 MAINTAINERS                          |   7 ++
 drivers/cpufreq/Kconfig.arm          |  10 ++
 drivers/cpufreq/Makefile             |   1 +
 drivers/cpufreq/cpufreq-dt-platdev.c |   3 +
 drivers/cpufreq/qcom-cpufreq-kryo.c  | 206 +++++++++++++++++++++++++++++++++++
 5 files changed, 227 insertions(+)
 create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c
MAINTAINERS +7 -0
index ba0adcb..648e0c8 100644
@@ -11687,6 +11687,13 @@ F:	Documentation/devicetree/bindings/media/qcom,camss.txt
 F:	Documentation/media/v4l-drivers/qcom_camss.rst
 F:	drivers/media/platform/qcom/camss-8x16/
 
+QUALCOMM CPUFREQ DRIVER MSM8996/APQ8096
+M:  Ilia Lin <[email protected]>
+L:  [email protected]
+S:  Maintained
+F:  Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
+F:  drivers/cpufreq/qcom-cpufreq-kryo.c
+
 QUALCOMM EMAC GIGABIT ETHERNET DRIVER
 M:	Timur Tabi <[email protected]>
 L:	[email protected]
drivers/cpufreq/Kconfig.arm +10 -0
index de55c7d..0bfd40e 100644
@@ -124,6 +124,16 @@ config ARM_OMAP2PLUS_CPUFREQ
 	depends on ARCH_OMAP2PLUS
 	default ARCH_OMAP2PLUS
 
+config ARM_QCOM_CPUFREQ_KRYO
+	bool "Qualcomm Kryo based CPUFreq"
+	depends on QCOM_QFPROM
+	depends on QCOM_SMEM
+	select PM_OPP
+	help
+	  This adds the CPUFreq driver for Qualcomm Kryo SoC based boards.
+
+	  If in doubt, say N.
+
 config ARM_S3C_CPUFREQ
 	bool
 	help
drivers/cpufreq/Makefile +1 -0
index 8d24ade..fb4a2ec 100644
@@ -65,6 +65,7 @@ obj-$(CONFIG_MACH_MVEBU_V7)		+= mvebu-cpufreq.o
 obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ)	+= omap-cpufreq.o
 obj-$(CONFIG_ARM_PXA2xx_CPUFREQ)	+= pxa2xx-cpufreq.o
 obj-$(CONFIG_PXA3xx)			+= pxa3xx-cpufreq.o
+obj-$(CONFIG_ARM_QCOM_CPUFREQ_KRYO)	+= qcom-cpufreq-kryo.o
 obj-$(CONFIG_ARM_S3C2410_CPUFREQ)	+= s3c2410-cpufreq.o
 obj-$(CONFIG_ARM_S3C2412_CPUFREQ)	+= s3c2412-cpufreq.o
 obj-$(CONFIG_ARM_S3C2416_CPUFREQ)	+= s3c2416-cpufreq.o
drivers/cpufreq/cpufreq-dt-platdev.c +3 -0
index 3b585e4..77d6ab8 100644
@@ -118,6 +118,9 @@
 
 	{ .compatible = "nvidia,tegra124", },
 
+	{ .compatible = "qcom,apq8096", },
+	{ .compatible = "qcom,msm8996", },
+
 	{ .compatible = "st,stih407", },
 	{ .compatible = "st,stih410", },
drivers/cpufreq/qcom-cpufreq-kryo.c new file +206 -0

206 lines not on this page · raw message

Signature · 1 line
1.9.1
author
#2 lore raw

PATCH v14 2/2 dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu

In reply to Ilia Lin

The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of operating-points-v2 table when it is parsed by the OPP framework.

This change adds documentation for the DT bindings.
The "operating-points-v2-kryo-cpu" DT extends the "operating-points-v2" with following parameters:
- nvmem-cells (NVMEM area containig the speedbin information)
- opp-supported-hw: A single 32 bit bitmap value, representing compatible HW:

			0:	MSM8996 V3, speedbin 0
			1:	MSM8996 V3, speedbin 1
			2:	MSM8996 V3, speedbin 2
			3:	unused
			4:	MSM8996 SG, speedbin 0
			5:	MSM8996 SG, speedbin 1
			6:	MSM8996 SG, speedbin 2
			7-31:	unused
Signed-off-by Ilia Lin <[email protected]>
Reviewed-by Rob Herring <[email protected]>
Acked-by Viresh Kumar <[email protected]>
---
 .../devicetree/bindings/opp/kryo-cpufreq.txt       | 680 +++++++++++++++++++++
 1 file changed, 680 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
Documentation/devicetree/bindings/opp/kryo-cpufreq.txt new file +680 -0
new file mode 100644
index 0000000..c2127b9
@@ -0,0 +1,680 @@
+Qualcomm Technologies, Inc. KRYO CPUFreq and OPP bindings
+===================================
+
+In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996
+that have KRYO processors, the CPU ferequencies subset and voltage value
+of each OPP varies based on the silicon variant in use.
+Qualcomm Technologies, Inc. Process Voltage Scaling Tables
+defines the voltage and frequency value based on the msm-id in SMEM
+and speedbin blown in the efuse combination.
+The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
+to provide the OPP framework with required information (existing HW bitmap).
+This is used to determine the voltage and frequency value for each OPP of
+operating-points-v2 table when it is parsed by the OPP framework.
+
+Required properties:
+--------------------
+In 'cpus' nodes:
+- operating-points-v2: Phandle to the operating-points-v2 table to use.
+
+In 'operating-points-v2' table:
+- compatible: Should be
+	- 'operating-points-v2-kryo-cpu' for apq8096 and msm8996.
+- nvmem-cells: A phandle pointing to a nvmem-cells node representing the
+		efuse registers that has information about the
+		speedbin that is used to select the right frequency/voltage
+		value pair.
+		Please refer the for nvmem-cells
+		bindings Documentation/devicetree/bindings/nvmem/nvmem.txt
+		and also examples below.
+
+In every OPP node:
+- opp-supported-hw: A single 32 bit bitmap value, representing compatible HW.
+		    Bitmap:
+			0:	MSM8996 V3, speedbin 0
+			1:	MSM8996 V3, speedbin 1
+			2:	MSM8996 V3, speedbin 2
+			3:	unused
+			4:	MSM8996 SG, speedbin 0
+			5:	MSM8996 SG, speedbin 1
+			6:	MSM8996 SG, speedbin 2
+			7-31:	unused
+
+Example 1:
+---------
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			clocks = <&kryocc 0>;
+			cpu-supply = <&pm8994_s11_saw>;
+			operating-points-v2 = <&cluster0_opp>;
+			#cooling-cells = <2>;
+			next-level-cache = <&L2_0>;
+			L2_0: l2-cache {
+			      compatible = "cache";
+			      cache-level = <2>;
+			};
+		};
+
+		CPU1: cpu@1 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+			clocks = <&kryocc 0>;
+			cpu-supply = <&pm8994_s11_saw>;
+			operating-points-v2 = <&cluster0_opp>;
+			#cooling-cells = <2>;
+			next-level-cache = <&L2_0>;
+		};
+
+		CPU2: cpu@100 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			clocks = <&kryocc 1>;
+			cpu-supply = <&pm8994_s11_saw>;
+			operating-points-v2 = <&cluster1_opp>;
+			#cooling-cells = <2>;
+			next-level-cache = <&L2_1>;
+			L2_1: l2-cache {
+			      compatible = "cache";
+			      cache-level = <2>;
+			};
+		};
+
+		CPU3: cpu@101 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x101>;
+			enable-method = "psci";
+			clocks = <&kryocc 1>;
+			cpu-supply = <&pm8994_s11_saw>;
+			operating-points-v2 = <&cluster1_opp>;
+			#cooling-cells = <2>;
+			next-level-cache = <&L2_1>;
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&CPU0>;
+				};
+
+				core1 {
+					cpu = <&CPU1>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&CPU2>;
+				};
+
+				core1 {
+					cpu = <&CPU3>;
+				};
+			};
+		};
+	};
+
+	cluster0_opp: opp_table0 {
+		compatible = "operating-points-v2-kryo-cpu";
+		nvmem-cells = <&speedbin_efuse>;
+		opp-shared;
+
+		opp-307200000 {
+			opp-hz = /bits/ 64 <307200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x77>;
+			clock-latency-ns = <200000>;
+		};
+		opp-384000000 {
+			opp-hz = /bits/ 64 <384000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-422400000 {
+			opp-hz = /bits/ 64 <422400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-460800000 {
+			opp-hz = /bits/ 64 <460800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-480000000 {
+			opp-hz = /bits/ 64 <480000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-537600000 {
+			opp-hz = /bits/ 64 <537600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-556800000 {
+			opp-hz = /bits/ 64 <556800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-614400000 {
+			opp-hz = /bits/ 64 <614400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-652800000 {
+			opp-hz = /bits/ 64 <652800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-691200000 {
+			opp-hz = /bits/ 64 <691200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-729600000 {
+			opp-hz = /bits/ 64 <729600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-768000000 {
+			opp-hz = /bits/ 64 <768000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-844800000 {
+			opp-hz = /bits/ 64 <844800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x77>;
+			clock-latency-ns = <200000>;
+		};
+		opp-902400000 {
+			opp-hz = /bits/ 64 <902400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-960000000 {
+			opp-hz = /bits/ 64 <960000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-979200000 {
+			opp-hz = /bits/ 64 <979200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1036800000 {
+			opp-hz = /bits/ 64 <1036800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1056000000 {
+			opp-hz = /bits/ 64 <1056000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1113600000 {
+			opp-hz = /bits/ 64 <1113600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1132800000 {
+			opp-hz = /bits/ 64 <1132800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1190400000 {
+			opp-hz = /bits/ 64 <1190400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1209600000 {
+			opp-hz = /bits/ 64 <1209600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1228800000 {
+			opp-hz = /bits/ 64 <1228800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1286400000 {
+			opp-hz = /bits/ 64 <1286400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1324800000 {
+			opp-hz = /bits/ 64 <1324800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x5>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1363200000 {
+			opp-hz = /bits/ 64 <1363200000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x72>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1401600000 {
+			opp-hz = /bits/ 64 <1401600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x5>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1440000000 {
+			opp-hz = /bits/ 64 <1440000000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1478400000 {
+			opp-hz = /bits/ 64 <1478400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1497600000 {
+			opp-hz = /bits/ 64 <1497600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x4>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1593600000 {
+			opp-hz = /bits/ 64 <1593600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x71>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1996800000 {
+			opp-hz = /bits/ 64 <1996800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x20>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2188800000 {
+			opp-hz = /bits/ 64 <2188800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x10>;
+			clock-latency-ns = <200000>;
+		};
+	};
+
+	cluster1_opp: opp_table1 {
+		compatible = "operating-points-v2-kryo-cpu";
+		nvmem-cells = <&speedbin_efuse>;
+		opp-shared;
+
+		opp-307200000 {
+			opp-hz = /bits/ 64 <307200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x77>;
+			clock-latency-ns = <200000>;
+		};
+		opp-384000000 {
+			opp-hz = /bits/ 64 <384000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-403200000 {
+			opp-hz = /bits/ 64 <403200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-460800000 {
+			opp-hz = /bits/ 64 <460800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-480000000 {
+			opp-hz = /bits/ 64 <480000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-537600000 {
+			opp-hz = /bits/ 64 <537600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-556800000 {
+			opp-hz = /bits/ 64 <556800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-614400000 {
+			opp-hz = /bits/ 64 <614400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-652800000 {
+			opp-hz = /bits/ 64 <652800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-691200000 {
+			opp-hz = /bits/ 64 <691200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-729600000 {
+			opp-hz = /bits/ 64 <729600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-748800000 {
+			opp-hz = /bits/ 64 <748800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-806400000 {
+			opp-hz = /bits/ 64 <806400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-825600000 {
+			opp-hz = /bits/ 64 <825600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-883200000 {
+			opp-hz = /bits/ 64 <883200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-902400000 {
+			opp-hz = /bits/ 64 <902400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-940800000 {
+			opp-hz = /bits/ 64 <940800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-979200000 {
+			opp-hz = /bits/ 64 <979200000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1036800000 {
+			opp-hz = /bits/ 64 <1036800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1056000000 {
+			opp-hz = /bits/ 64 <1056000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1113600000 {
+			opp-hz = /bits/ 64 <1113600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1132800000 {
+			opp-hz = /bits/ 64 <1132800000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1190400000 {
+			opp-hz = /bits/ 64 <1190400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1209600000 {
+			opp-hz = /bits/ 64 <1209600000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1248000000 {
+			opp-hz = /bits/ 64 <1248000000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1286400000 {
+			opp-hz = /bits/ 64 <1286400000>;
+			opp-microvolt = <905000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1324800000 {
+			opp-hz = /bits/ 64 <1324800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1363200000 {
+			opp-hz = /bits/ 64 <1363200000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1401600000 {
+			opp-hz = /bits/ 64 <1401600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1440000000 {
+			opp-hz = /bits/ 64 <1440000000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1478400000 {
+			opp-hz = /bits/ 64 <1478400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1555200000 {
+			opp-hz = /bits/ 64 <1555200000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1593600000 {
+			opp-hz = /bits/ 64 <1593600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1632000000 {
+			opp-hz = /bits/ 64 <1632000000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1670400000 {
+			opp-hz = /bits/ 64 <1670400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1708800000 {
+			opp-hz = /bits/ 64 <1708800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1747200000 {
+			opp-hz = /bits/ 64 <1747200000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x70>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1785600000 {
+			opp-hz = /bits/ 64 <1785600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1804800000 {
+			opp-hz = /bits/ 64 <1804800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x6>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1824000000 {
+			opp-hz = /bits/ 64 <1824000000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x71>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1900800000 {
+			opp-hz = /bits/ 64 <1900800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x74>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1920000000 {
+			opp-hz = /bits/ 64 <1920000000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1977600000 {
+			opp-hz = /bits/ 64 <1977600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x30>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1996800000 {
+			opp-hz = /bits/ 64 <1996800000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2054400000 {
+			opp-hz = /bits/ 64 <2054400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x30>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2073600000 {
+			opp-hz = /bits/ 64 <2073600000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2150400000 {
+			opp-hz = /bits/ 64 <2150400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x31>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2246400000 {
+			opp-hz = /bits/ 64 <2246400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x10>;
+			clock-latency-ns = <200000>;
+		};
+		opp-2342400000 {
+			opp-hz = /bits/ 64 <2342400000>;
+			opp-microvolt = <1140000 905000 1140000>;
+			opp-supported-hw = <0x10>;
+			clock-latency-ns = <200000>;
+		};
+	};
+
+....
+
+reserved-memory {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	ranges;
+....
+	smem_mem: smem-mem@86000000 {
+		reg = <0x0 0x86000000 0x0 0x200000>;
+		no-map;
+	};
+....
+};
+
+smem {
+	compatible = "qcom,smem";
+	memory-region = <&smem_mem>;
+	hwlocks = <&tcsr_mutex 3>;
+};
+
+soc {
+....
+	qfprom: qfprom@74000 {
+		compatible = "qcom,qfprom";
+		reg = <0x00074000 0x8ff>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		....
+		speedbin_efuse: speedbin@133 {
+			reg = <0x133 0x1>;
+			bits = <5 3>;
+		};
+	};
+};
Signature · 1 line
1.9.1
Reviewed-by Tested-by on the v14 series
#3 lore raw
In reply to Ilia Lin
Quoted 33 lines · Ilia Lin

[v14]
* Addressed comment from Sudeep about DT compatible
* Added MAINTAINERS entry

[v13]
* Addressed comment from Sudeep about DT compatible check on init

[v12]
* Addressed comments from Sudeep and Viresh about the single init

[v11]
* Addressed comment from Russel about device_node reference
* Addressed comment from Sudeep about the late_initcall
* Transformed init into probe to take care of deferals

[v10]
* Split the series into domains
* Addressed comments from Viresh and Sudeep about logical CPU numbering.

The qcom-cpufreq-kryo driver is aimed to support different SOC versions. The driver reads eFuse information and chooses the required OPP subset by passing the OPP supported-hw parameter.

The series depends on the series from Viresh:
https://patchwork.kernel.org/patch/10418139/

The previous spin was here:
https://patchwork.kernel.org/patch/10424949/

Ilia Lin (2):
cpufreq: Add Kryo CPU scaling driver
dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu

Quoted 10 lines
 .../devicetree/bindings/opp/kryo-cpufreq.txt       | 680 +++++++++++++++++++++
 MAINTAINERS                                        |   7 +
 drivers/cpufreq/Kconfig.arm                        |  10 +
 drivers/cpufreq/Makefile                           |   1 +
 drivers/cpufreq/cpufreq-dt-platdev.c               |   3 +
 drivers/cpufreq/qcom-cpufreq-kryo.c                | 206 +++++++
 6 files changed, 907 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
 create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c

FWIW,

Reviewed-by Amit Kucheria <[email protected]>
Tested-by Amit Kucheria <[email protected]>
maintainer
#4 lore raw
In reply to Ilia Lin
Quoted 3 lines · Ilia Lin

[v14]
* Addressed comment from Sudeep about DT compatible
* Added MAINTAINERS entry

This causes a build issue to occur in my bleeding-edge branch.

Does it depend on anything new in arm-soc?

Thanks,
Rafael

maintainer
#5 lore raw
Quoted 8 lines · Rafael J. Wysocki
Quoted 3 lines · Ilia Lin

[v14]
* Addressed comment from Sudeep about DT compatible
* Added MAINTAINERS entry

This causes a build issue to occur in my bleeding-edge branch.

Does it depend on anything new in arm-soc?

He already sent a v15 and the changelog suggest he fixed that build issue.

Signature · 1 line
viresh
author
#6 lore raw

Just like Viresh said, this is fixed in the v15.

Quoted 13 lines · Viresh Kumar
Quoted 1 line · Rafael J. Wysocki

On Fri, May 25, 2018 at 2:07 PM, Ilia Lin <[email protected]>

Quoted 7 lines · wrote:
Quoted 3 lines

[v14]
* Addressed comment from Sudeep about DT compatible
* Added MAINTAINERS entry

This causes a build issue to occur in my bleeding-edge branch.

Does it depend on anything new in arm-soc?

He already sent a v15 and the changelog suggest he fixed that build issue.

Signature · 1 line
Sent from my Android device with K-9 Mail. Please excuse my brevity.