spi: designware_spi: Add reset ctrl to driver
PATCH v2 1/1 spi: designware_spi: Add reset ctrl to driver
Add code to reset all reset signals as in SPI DT node. A reset property is an optional feature, so only print out a warning and do not fail if a reset property is not present.
If a reset property is discovered, then use it to deassert, thus bringing the IP out of reset.
Release reset when _remove().
---
v2:
- Fix multi-lines comment style
--- drivers/spi/designware_spi.c | 43 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 43 insertions(+)
drivers/spi/designware_spi.c +43 -0
@@ -17,6 +17,7 @@#include <malloc.h> #include <spi.h> #include <fdtdec.h> +#include <reset.h> #include <linux/compat.h> #include <linux/iopoll.h> #include <asm/io.h>
@@ -111,6 +112,8 @@ struct dw_spi_priv {void *tx_end;void *rx;void *rx_end; + +struct reset_ctl_bulk resets; };static inline u32 dw_read (struct dw_spi_priv *priv,u32 offset)
@@ -231,6 +234,34 @@ err_rate:return -EINVAL ; } +static int dw_spi_reset (struct udevice *bus) +{ +int ret; +struct dw_spi_priv *priv =dev_get_priv (bus); + + ret =reset_get_bulk (bus, &priv->resets); +if (ret) { +/* +* Return 0 if error due to !CONFIG_DM_RESET and reset +* DT property is not present. +*/ +if (ret == -ENOENT || ret == -ENOTSUPP ) +return 0 ; + +dev_warn (bus,"Can't get reset: %d\n" , ret); +return ret; + } + + ret =reset_deassert_bulk (&priv->resets); +if (ret) { +reset_release_bulk (&priv->resets); +dev_err (bus,"Failed to reset: %d\n" , ret); +return ret; + } + +return 0 ; +} +static int dw_spi_probe (struct udevice *bus) {struct dw_spi_platdata *plat =dev_get_platdata (bus);
@@ -244,6 +275,10 @@ static int dw_spi_probe(struct udevice *bus)if (ret)return ret; + ret =dw_spi_reset (bus); +if (ret) +return ret; +/* Currently only bits_per_word == 8 supported */ priv->bits_per_word =8 ;
@@ -478,6 +513,13 @@ static int dw_spi_set_mode(struct udevice *bus, uint mode)return 0 ; } +static int dw_spi_remove (struct udevice *bus) +{ +struct dw_spi_priv *priv =dev_get_priv (bus); + +return reset_release_bulk (&priv->resets); +} +static const struct dm_spi_ops dw_spi_ops = { .xfer = dw_spi_xfer, .set_speed = dw_spi_set_speed,
@@ -502,4 +544,5 @@ U_BOOT_DRIVER(dw_spi) = { .platdata_auto_alloc_size = sizeof(struct dw_spi_platdata), .priv_auto_alloc_size = sizeof(struct dw_spi_priv), .probe = dw_spi_probe, + .remove = dw_spi_remove, };
Signature · 1 line
2.2.2
PATCH v2 1/1 spi: designware_spi: Add reset ctrl to driver
Quoted 4 lines · Ley Foon Tan
Add code to reset all reset signals as in SPI DT node. A reset property is an optional feature, so only print out a warning and do not fail if a reset property is not present.
Quoted 8 lines
If a reset property is discovered, then use it to deassert, thus bringing the IP out of reset.
Release reset when
_remove().Signed-off-by Ley Foon Tan <[email protected]>Acked-by Marek Vasut <[email protected]>Reviewed-by Jagan Teki <[email protected]>
Applied to u-boot-spi/master