Skip to contentSkip to conversation

ASoC: q6afe: dt-bindings: Update input range for qcom,sd-lines

PATCH In review Rohit kumar 2 participants 2 messages Sep 19, 2018

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ASoC: q6afe: dt-bindings: Update input range for qcom,sd-lines

Input to qcom,sd-lines should be between 0 and 3 instead of 1 to 4 as 0 corresponds to BIT(0) which is MI2S_SD0 line. Bit 1 to 3 corresponds to SD1 to SD3 lines respectively. Updated documentation for the same.

---
 Documentation/devicetree/bindings/sound/qcom,q6afe.txt | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)
Documentation/devicetree/bindings/sound/qcom,q6afe.txt +9 -9
index a817940..d74888b 100644
@@ -49,7 +49,7 @@ configuration of each dai. Must contain the following properties.
 	Usage: required for mi2s interface
 	Value type: <prop-encoded-array>
 	Definition: Must be list of serial data lines used by this dai.
-	should be one or more of the 1-4 sd lines.
+	should be one or more of the 0-3 sd lines.
 
  - qcom,tdm-sync-mode:
 	Usage: required for tdm interface
@@ -137,42 +137,42 @@ q6afe@4 {
 
 		prim-mi2s-rx@16 {
 			reg = <16>;
-			qcom,sd-lines = <1 3>;
+			qcom,sd-lines = <0 2>;
 		};
 
 		prim-mi2s-tx@17 {
 			reg = <17>;
-			qcom,sd-lines = <2>;
+			qcom,sd-lines = <1>;
 		};
 
 		sec-mi2s-rx@18 {
 			reg = <18>;
-			qcom,sd-lines = <1 4>;
+			qcom,sd-lines = <0 3>;
 		};
 
 		sec-mi2s-tx@19 {
 			reg = <19>;
-			qcom,sd-lines = <2>;
+			qcom,sd-lines = <1>;
 		};
 
 		tert-mi2s-rx@20 {
 			reg = <20>;
-			qcom,sd-lines = <2 4>;
+			qcom,sd-lines = <1 3>;
 		};
 
 		tert-mi2s-tx@21 {
 			reg = <21>;
-			qcom,sd-lines = <1>;
+			qcom,sd-lines = <0>;
 		};
 
 		quat-mi2s-rx@22 {
 			reg = <22>;
-			qcom,sd-lines = <1>;
+			qcom,sd-lines = <0>;
 		};
 
 		quat-mi2s-tx@23 {
 			reg = <23>;
-			qcom,sd-lines = <2>;
+			qcom,sd-lines = <1>;
 		};
 	};
 };
Signature · 2 lines
Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center, Inc.,
is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.
maintainer
#1 lore raw

Applied "ASoC: q6afe: dt-bindings: Update input range for qcom,sd-lines" to the asoc tree

The patch

ASoC: q6afe: dt-bindings: Update input range for qcom,sd-lines

has been applied to the asoc tree at

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark

Quoted 1 line

From 3a6818c771671c34b090244c92ab5aea6176d6da Mon Sep 17 00:00:00 2001

From: Rohit kumar <[email protected]>
Date: Wed, 19 Sep 2018 11:41:21 +0530
Subject: [PATCH] ASoC: q6afe: dt-bindings: Update input range for
qcom,sd-lines

Input to qcom,sd-lines should be between 0 and 3 instead of 1 to 4 as 0 corresponds to BIT(0) which is MI2S_SD0 line. Bit 1 to 3 corresponds to SD1 to SD3 lines respectively. Updated documentation for the same.

---
 .../devicetree/bindings/sound/qcom,q6afe.txt   | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)
Documentation/devicetree/bindings/sound/qcom,q6afe.txt +9 -9
index a8179409c194..d74888b9f1bb 100644
@@ -49,7 +49,7 @@ configuration of each dai. Must contain the following properties.
 	Usage: required for mi2s interface
 	Value type: <prop-encoded-array>
 	Definition: Must be list of serial data lines used by this dai.
-	should be one or more of the 1-4 sd lines.
+	should be one or more of the 0-3 sd lines.
 
  - qcom,tdm-sync-mode:
 	Usage: required for tdm interface
@@ -137,42 +137,42 @@ q6afe@4 {
 
 		prim-mi2s-rx@16 {
 			reg = <16>;
-			qcom,sd-lines = <1 3>;
+			qcom,sd-lines = <0 2>;
 		};
 
 		prim-mi2s-tx@17 {
 			reg = <17>;
-			qcom,sd-lines = <2>;
+			qcom,sd-lines = <1>;
 		};
 
 		sec-mi2s-rx@18 {
 			reg = <18>;
-			qcom,sd-lines = <1 4>;
+			qcom,sd-lines = <0 3>;
 		};
 
 		sec-mi2s-tx@19 {
 			reg = <19>;
-			qcom,sd-lines = <2>;
+			qcom,sd-lines = <1>;
 		};
 
 		tert-mi2s-rx@20 {
 			reg = <20>;
-			qcom,sd-lines = <2 4>;
+			qcom,sd-lines = <1 3>;
 		};
 
 		tert-mi2s-tx@21 {
 			reg = <21>;
-			qcom,sd-lines = <1>;
+			qcom,sd-lines = <0>;
 		};
 
 		quat-mi2s-rx@22 {
 			reg = <22>;
-			qcom,sd-lines = <1>;
+			qcom,sd-lines = <0>;
 		};
 
 		quat-mi2s-tx@23 {
 			reg = <23>;
-			qcom,sd-lines = <2>;
+			qcom,sd-lines = <1>;
 		};
 	};
 };
Signature · 1 line
2.19.0